Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/9300697125507_63bd7334-f271-415d-b592-e87a61393893.png?v=1754711822&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$19.36
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/9300697125491_a8d0ece3-568d-4821-8809-5e34c2a6b17a.png?v=1754711824&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$19.36
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/9300697125477_ccd4da12-d606-410c-8ff3-ba3179929f1c.png?v=1754711825&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$19.36
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$17.85
![Selleys No More Gaps Multipurpose Sealant Filler 475g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115263_d81e146e-2bcf-410a-bcad-ef2cdb518343.png?v=1754711828&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$14.11
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697128966_f7f1ad95-c5c9-4fcb-b790-2ec77b1fecc0.jpg?v=1754711830&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$8.83
![Selleys No More Gaps Filler Sealant Fast Dry [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697123251_8547a626-b098-4c8e-9dee-9c36f9b972a8.png?v=1754711833&width=645)
Selleys No More Gaps Fast Dry has been designed to be painted over in just 20 minutes so that you can finish the job sooner! No More Gaps Fast Dry also provides superior crack resistance with high flexibility and low shrinkage. Features Paint over in 20 minutes* Superior crack resistance Superior adhesion to a broad range of surfaces, resulting in a lasting finish A smooth flawless finish and minimal shrinkage Can be cleaned up easily and quickly with water Will not stain building materials Can be used indoors and outdoors *Allow longer drying times before painting with flat or ceiling paints or in cooler weather. Where can this product be used? Architraves Skirting boards Cornices Window and door frames Wall joints What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Painted surfaces Many other building materials How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into caulking gun such as Selleys Light Speed Caulking gun. Apply with caulking gun, forcing product into gap. For a smooth finish, smooth with a finger dipped in water. For a professional finish use a paint scraper such as a 50mm Soft Grip Scraper. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow to skin (about 20 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Limitations: For gaps between tongue and groove boards and weatherboards use No More Gaps® Exterior & Weatherboard. Where movement is excessive or for areas where contact with water is frequent, use the appropriate Selleys® Silicone Sealant. Handy Tips To avoid paint cracking, apply at temperatures above 10°C and do not apply paint too thick. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler, and a perfect finish. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to skin prior to painting, which is approximately 20 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. For exterior applications protect from rain until firmly skinned. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$9.35
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697123718_ba862328-1e1f-4607-80f6-dbe7568e7040.png?v=1754711835&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.96
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$12.17
Selleys Liquid Nails Instant Hold is a high performance advanced polymer construction adhesive that delivers an instant hold on any building material*, even vertical surfaces. It is heat, UV and water resistant and doesn’t require fasteners or clamps for many applications so you can get on with the next job. Powered by Sil-X Advanced Polymer Technology. Features Instant Hold on any building material* Up to 400kgs M2 No need to clamp* High Strength & flexibility Indoor/Outdoor Adheres to wet and damp surfaces and can be applied on wet surface^ Cure time of 48 hours Paintable after 24 hours with water based paints. Solvent based paints may be used after first painting with a water based paint Adjustable e.g. can be straightened for up to 15 minutes Powered by Sil-X Advanced Polymer Technology *Holds instantly but must not be disturbed until fully cured. Weight is restricted for non-porous substrates including metal & glass – support may be required where the object exceeds 5kgs. ^Not for permanent water immersion What Materials is this product suitable for? Timber MDF Plasterboard Some plastics Masonry Concrete Particleboard Metals Glass Tiles & ceramics How to use the product Ensure surfaces are clean and free from grease or loose particles Use a high thrust caulking gun and the supplied V-notch nozzle to apply in vertical stripes 5cm apart. Ensure the V shape is angled upward when applying. Position materials and press together firmly. Due to the high initial hold of the product support during curing is not necessary (subject to weight limitations for non-porous surfaces). Holds instantly but must not be disturbed until cured (up to 48 hours). Adjustable e.g. can be straightened for up to 15 minutes Handy Tips Clean up with turps before the adhesive cures Safety Information KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well ventilated area. Wash hands after use. If on skin: Wash with soap and water. Product releases methanol during cure. Refer to Safety Data Sheet. Storage & re-use Cure product before disposal Store in a cool place. The adhesive should be used within 6 months after opening. If the adhesive is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess adhesive from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be disposed.
$18.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$7.42
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$16.79
Selleys Ezi Press Liquid Nails Fast water based high strength construction adhesive is the NEW easy to use application system that does not require a caulking gun. Simply apply at the press of a lever. Perfect for sticking materials together such as architraves and skirting. Key Benefits No caulking gun required Easily applied with a press of a lever Flow control for precise application and finish with no run on Features Fast grab minimises slippage when adhering on vertical surfaces and minimises the need to support joints while it cures. Water based, so it is faster to clean up. Less mess and fuss. Low odour making it ideal for indoor jobs. Heat resistant meaning the integrity of the bond will remain when exposed to direct sunlight. Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Paintable after 12 hours. Cures and works best on porous surfaces, which makes it ideal for sticking wall panels to masonry. Doesn’t drip, sag or string, so there is less mess when you are using the product Bridges gaps on rough and ill fitting construction material Not for use on polyethylene, polypropylene, Teflon or silicone. Perfect for indoor projects: Timber panelling to walls Skirting boards Styrene foam panels and blocks Architraves Particle board to masonry surfaces Tasks where nailing is not desirable For sheet timber flooring to flat surfaces LIQUID NAILS High Strength is recommended. Not suitable for use for polyethylene and polypropylene. Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. What materials is this product suitable for? MDF Particleboard Plasterboard Rubber & Glass Architraves Skirting boards Cornices Timber Polystyrene Foam Concrete and Masonry Tiles and ceramics Most plastic – pre test plastic to determine compatibility How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. Surfaces should not be visibly wet or constantly damp. Oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, as the construction adhesive will adhere more readily to a scratched up surface. Ezi Press remove cap Remove tab lock and nozzle cap. Twist collar clockwise towards MAX and adjust between MIN and MAX to control flow. Ezi Press application Simply press lever gently to dispense filler to surface. On broad flat surfaces apply beads every 40cm, on smaller surfaces apply dots. Bring surfaces together as soon as possible (within first 5 mins). Fix with sufficient nails, screws or clamping to hold load. Ezi Press min max Clean up with a damp cloth, twist collar back to MIN and replace nozzle cap. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For higher initial grab, apply to one surface only, press together and pull apart. Allow to dry for up to 5 min (no longer) before firmly joining. For porous substrates, a good bond strength is achieved after 24 hours and will continue to strengthen over a 2-3 day period. The time it takes to form a strong bond depends on the nature and conditions of the application. In cold or damp weather and between non porous materials, the drying time is greatly extended. When the product is still wet it can be removed with warm soapy water or a damp cloth, otherwise if the product is dry it can be removed by sanding or scraping.
$14.58
Selleys Craft Glue is a water-based PVA adhesive specially formulated for quick adhesion for craft work. The product is an off-white paste which is clear when dry. Features Easy to use – no mixing ready to use straight from the pack and only need to apply to one surface Fast Drying – initial bond can usually be achieved in a few seconds Dries clear Spills don’t stain and it’s easy to clean up with a wet rag Non-toxic – low odour and environmentally friendly Contains no flammable solvents Solvent-free – no fumes and non-flammable Appearance White milky liquid that dries clear Where can this product be used? Re-attach book cover/spine or repair torn bindings Craft/hobby work On very porous or open weave fabrics extra adhesive may be required for optimum bond strength Craft glue has limited water resistance In very cold or damp conditions the adhesive is slower setting What materials is this product suitable for? Fabrics Felt Cardboard Leather Suede Wood Paper Most plastic films (other than polyethylene and polypropylene) Sequins How to use this product Ensure surfaces to be joined are clean, dust and lint free. Shake bottle well before use. Unscrew cap to expose nozzle. Apply a thin coat of Selleys Craft Glue to one surface and press together. Hold in position with light pressure for a few seconds, or longer for very absorbent surfaces. Clean up excess glue quickly with a damp cloth. Wipe nozzle clean and replace cap after use. Handy tips On very porous surfaces applying a thin layer to each side and allowing it to soak in before applying a second layer to one side only may result in a stronger bond. Glue can be resoftened by soaking the item in warm water or by application of acetone. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. Safety tips Avoid eye contact, if contact occurs flush with plenty of water for 15 minutes and seek medical advice. Storage and re-use Clean up excess glue quickly with a damp cloth. Wipe nozzle clean and replace cap after use.
$15.00
Selleys MarineFlex delivers a waterproof seal for joints & gaps, even under water*. Suitable for boats, pools & spas. MarineFlex high-performance adhesive sealant can be used on boats, pools & spas, where you need a waterproof seal or bond, even underwater* It can be applied & will cure under water – no need to drain your pool or spa. Compared to traditional polyurethanes it provides a more durable seal & bond with superior UV resistance. Features Salt, fresh & chlorinated water (pools/spas)^ Above and below the waterline No primer required Shock absorbing & vibration dampening Solvent & isocyanate free Sandable when fully cured Powered by Sil-X advanced polymer technology Limitations #Not suitable for PP, PE or PTFE *critical seals/repairs underwater should be regularly checked & repaired if required. Not for polycarbonate and Perspex underwater ^Gelcoat must be lightly sanded prior to product application Where can this product be used? Suitable for boats, pools & spas^ What materials is this product suitable for? Metals Glass Ceramic Tiles Sealed/painted timber & concrete Fibreglass Gelcoat* Most plastics# (pre-test before use)
$23.20
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$32.27
![Selleys Armour Flex High Performance Adhesive [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125286_24a1028f-4655-4200-8859-8e45b8c9ab19.jpg?v=1754711936&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
Selleys Aquadhere Quick Set is a quick setting PVA wood glue that is suitable for all types of wood, sets twice as fast compared to normal PVAs and requires no clamping in many situations*. It will bond almost anything your craft work calls for! Features Fast bonding No clamping* Convenient and easy to use Non-toxic, water clean-up Dries clear *No need for clamping where joints are not under stress and timber is not bowed, warped etc Where can this product be used? School projects Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window frame Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Decorating What materials is this product suitable for? Interior wood Carboard Paper Fabric Felt Leather How to Use Surfaces to be bonded must be close fitting, dry and clean. Shake bottle and apply thinly to one surface. Press surfaces together firmly for 1-2 minutes. Wipe off excess adhesive with a damp cloth whilst still wet If joint is under stress or timber is bowed or warped, clamp until adhesive sets. Adhesive strength will be sufficient for object to be handled after 5-10 minutes for softwoods and 15-20 minutes for hardwoods. Allow 30-60 minutes before working with object. Maximum strength is attained in 4-8 hours. Allow longer setting/bonding time in cold or humid conditions. Limitations: Not for exterior use. Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere Quick Set is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Selleys Aquadhere exterior or Selleys Aquadhere Durabond). Will not take timber stains. Aquadhere Quick Set is not recommended for joints that are subjected to constant high stress. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Selleys Aquadhere Exterior.
$23.07
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$6.65
$51.95
$29.03
$81.92
$40.16
Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.
$17.82
Selleys 655FC: Crystal Clear Sealant & Adhesive with Instant Grab Key Features Superior Strength & Instant Grab 100% Clear Finish Fast Curing Adhesion to Wet Surfaces* Applications Can be used for sealing, bonding, and filling on both interior and exterior surfaces such as concrete, timber, metal, and more. Compatibility Suitable for a wide range of building materials including concrete, timber, metals, and most plastics. How to Use Ensure surfaces are clean and dry. Cut the nozzle at an angle and apply using a sealant gun. Tool with a round spatula within 10 minutes for best results. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Handy Tips Paintable immediately with water-based paints. Adhesion improves as the sealant dries.
$22.79
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$22.79
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$19.25
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$15.92
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/0799439671669_6c8563d0-64cb-499e-a564-d2d4a62e9ce2.png?v=1754712007&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/0793591712994_c9bef70a-42d0-408c-8b14-e176578d110d.png?v=1754712009&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/0793591712987_0ace0873-9628-42fc-9b06-c64c93c74c40.png?v=1754712010&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$46.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$7.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$28.90
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$4.43
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$13.50
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$15.74
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$68.31
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$11.52
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$22.98
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$8.12
Polyfilla Ultra Nails 320g: The All-in-One Construction Adhesive Features & Benefits High-strength bonding for a wide range of materials Repositionable for up to 20 minutes Waterproof For use on concrete, brick, plasterboard, and more Coverage: 15 meters of 5mm bead Dry time: Initial bond within 24 hours Application Guidelines For best results, ensure surfaces are clean and free from dust, grease, and pooled water. Apply as per directions for wall panelling, flooring, and contact bonds. Mechanical fasteners are recommended for heavy loads. Safety Precautions Use in a well-ventilated area and wear protective gloves and eye protection. Keep away from heat sources. If swallowed, seek medical advice immediately. Available Sizes and Colours Available in: 320g Colour: Brown Cleanup Use mineral turpentine for cleanup.
$5.85
Polyfilla P10 Gap Filler Rapid: The Ultra-Fast Solution for Perfect Fills Features Flexible Smooth Finish Rapid Drying Paintable in 10 minutes* Low Shrinkage Crack-Resistant* Applications Ideal for filling gaps around cornices, wall joints, skirting boards, as well as inside windows and door frames. Usage Instructions *To avoid paint cracking, apply to gaps no larger than 5mm deep and 10mm wide at temperatures above 20°C. Allow the sealant to dry before painting. Avoid applying paint too thickly. When to Use Paintable in just 10 minutes, allowing for fast project completion.
$7.35
Polyfilla F20 Gap Filler: The Ultimate Gap Solution for High-Stress Applications Features Highly Durable High Flexibility Smooth Finish +/- 20% Joint Movement Capability Product Description Polyfilla F20 Gap Filler has been specially formulated to offer superior flexibility in high-stress interior and exterior applications. With up to +/- 20% joint movement capability, this gap filler is ideal for filling gaps around cornices, wall joints, skirting boards, as well as window and door frames. Application This product is extremely easy to use. Simply ensure the area is clean and dry, apply the filler, and allow it to dry. It adheres well to multiple surfaces and offers long-lasting results. Use Cases Cornices Wall Joints Skirting Boards Window & Door Frames
$8.10
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
$5.00
You have seen 96 out of 160 products
Products formulated to reduce smell during application and cure, perfect for indoor projects and tight spaces. Ventilation is still recommended. Use filters to refine by chemistry, set speed and temperature rating. Always review the product page and TDS/SDS for handling and cure guidance.
