Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
Bonds most materials within 30 seconds High-viscosity allows for greater accuracy and detail Large 100ml container Integrated nozzle for easy application Ritetite Control is a one-component gel super glue that bonds extremely quickly. It’s made with a specially designed thixotropic formula that instantly polymerises (hardens) by absorbing surface moisture. Its fast-curing properties make it an excellent choice for high-speed industrial applications that require a gel-like, viscous adhesive that does not spread or leak like traditional super glue. Ritetite Control works exceptionally well in poor-fitting applications such as rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber bonding due to its thick gel consistency. Surface Preparation prior to bonding with RITETITE CONTROL Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE CONTROL Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$54.39
Ultra-High strength supa glue that dries clear. Gives great strength as well as flexibility and heat resistance. Performance above and beyond normal Supa Glue. Features Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve an initial bond Self-piercing, clog-free cap Forms a strong, flexible bond Impact Resistant – 4 times greater impact resistance than normal supa glues Superior bond on metals – up to 6 times stronger bond on steel than normal supa glue. Up to 4 times stronger bond on aluminium than normal supa glues Heat Resistant to 120°C permanently, 150°C intermittently Comes with a nozzle for easy, accurate application Appearance Clear thick liquid dries to a colourless film. Where can this product be used? Ideal for small repair jobs or when immediate results are required Fixing a broken door knocker Refixing wooden or metal door handles Repairing crockery safe to put in the dishwasher Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or other materials containing alkaline elements Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals Wood China Rubber Leather (test first as leather may become hardened or discoloured) Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Refer to handy hints for cleaning tips. Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. Allow 12 hours for sufficient bond strength for practical use. Handy tips Supa Glue can create a white residue on the surface of materials if the area is not well ventilated. Clean the affected area with acetone to remove (most nail polish removers) residue. Excellent when used with other adhesives, as the temporary tack. For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. In the event that fingers get stuck together – don’t panic! Slowly twist fingers in the opposite direction in hot soapy water. Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from the skin. While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin is soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary to apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. Do not use near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$7.00
An all purpose, high strength household glue that unlike standard superglues is extremely ‘infinitely’ more flexible. It can repair and bond a variety of surfaces and withstand the most extreme/rough conditions whilst providing the ultimate bond. Features Strong Bond Ultra Flexible – infinitely more flexible* Extreme Resistance to: Shocks & Vibration, Torsion & Movement, Water and Extreme Temperatures Dishwasher Safe Gap Filling (works on uneven surfaces) Paintable Adjustable for 1min Non-Drip (great for vertical surfaces) Interior/Exterior Easy to use Heat resistant -15°C to +120°C Solvent free, no shrinkage Colour Dries translucent What materials is this product suitable for? Metal Wood Glass Rubber China Leather Ceramics Masonry Fibreglass Vinyl Cardboard Fabric Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place Safety Tips On contact, uncured adhesive can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice. Avoid contact with skim. If contact occurs, wipe off and wash with detergent. Avoid breathing vapours. Use in a well ventilated area
$12.00
Quick Fix No Mess Stand Up Tube is the Supa Smart Supa Glue. The tube controls the flow of adhesive for precise applications and will retract partly dispensed glue from the nozzle so it will never clog up and dry out between uses. The stand up feature also means you don’t end up with messy drops of glue on the benchtop! Features -Free standing tube prevents leaks and retracts party dispensed glue -Prevents squeeze out and provides maximum application control -Bonds a variety of surfaces -Extremely fast setting, sets in 10 seconds -Maximum strength achieved in 12 hours -Dries clear for clean, neat results -Water resistant -No clamping necessary -Self piercing, clog free cap -Forms a rigid bond Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Pierce seal at end of tube by attaching nozzle and cap and turning clockwise. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. The product grabs within 2-30 seconds, depending on environmental conditions and materials to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Handy tips Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone (most nail polish removers) to remove residue. Excellent when used with other adhesives, as the temporary tack. For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from skin. While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Hand Kleen Wipes nearby for a quick and effective cleanup. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$6.00
Fast setting ethyl cyanoacrylate (supa glue) based adhesive with a non-drip gel consistency which dries clear. Features -Bonds a variety of surfaces -Extremely fast setting -Dries Clear for clean, neat results -Water resistant -No clamping necessary -No mixing required -Maximum strength achieved in 12 hours -Only takes 45 seconds to achieve an initial bond -Self-piercing, clog-free cap -Forms a rigid bond -The non-drip gel consistency is ideal for vertical jobs -Can be used for gap filling due to the gel consistency Where can this product be used? -The non-drip gel consistency makes it particularly useful on vertical surfaces -Ideal for small repair jobs or when immediate results are required -For interior projects and repairs. -Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Leather may become hardened or discoloured -Not suitable for repairing items that are in direct contact with hot liquids eg saucepans -Will not permanently bond glass or materials containing alkaline elements What materials is this product suitable for? -Bonds a variety of porous and non-porous surfaces -Metals -Wood -China -Rubber -Leather (test first as some leather may become hardened or discoloured) -Some plastics How to use this product -Supa Glue non-drip gel works best when the surfaces to be bonded are close fitting, but a small amount of gap filling is possible. -Surfaces to be bonded should be clean, dry and free of dust. -Pierce seal at end of tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. -The product grabs within 2-30 seconds, depending on environmental conditions and substrates to be bonded. -Allow 30 minutes for sufficient bond strength for practical use. Handy tips -Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone, to remove residue. -Use Quick Fix Gel on vertical surfaces. -Excellent when used with other adhesives, as the temporary tack. -For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. -After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. -Quickfix gel is good for use on wood & porous surfaces (e.g terracotta pots) as it doesn’t soak into the surface like a liquid would. -Acetone ( most nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. -Since Quick Fix cures with moisture, set times may be extended on very dry surfaces or under dry conditions. -Super glues cure more slowly when large amounts are used. For faster cure use sparingly. -While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. -Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. Safety tips -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. -Do not use near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non toxic when set -For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$7.00
Fast setting ethyl cyanoacrylate (suclog-freebased adhesive with a non-drip gel consistency which dries clear. Features: -Bonds a variety of surfaces -Extremely fast setting -Dries Clear for clean, neat results -Water resistant -No clamping necessary -No mixing required -Maximum strength achieved in 12 hours -Only takes 45 seconds to achieve an initial bond -Self-piercing, clog-free cap -Forms a rigid bond -The non-drip gel consistency is ideal for vertical jobs -Can be used for gap filling due to a gel consistency Where can this product be used? -The non-drip gel consistency makes it particularly useful on vertical surfaces -Ideal for small repair jobs or when immediate results are required -For interior projects and repairs. -Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Leather may become hardened or discoloured -Not suitable for repairing items that are in direct contact with hot liquids eg saucepans -Will not permanently bond glass or materials containing alkaline elements What materials is this product suitable for? -Bonds a variety of porous and non-porous surfaces -Metals -Wood -China -Rubber -Leather (test first as some leather may become hardened or discoloured) -Some plastics How to use this product -Supa Glue non-drip gel works best when the surfaces to be bonded are close fitting, but a small amount of gap filling is possible. -Surfaces to be bonded should be clean, dry and free of dust. -Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. -The product grabs within 2-30 seconds, depending on environmental conditions and substrates to be bonded. -Allow 30 minutes for sufficient bond strength for practical use. Handy tips -Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone, to remove residue. -Use Quick Fix Gel on vertical surfaces. -Excellent when used with other adhesives, as the temporary tack. -For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. -After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. -Quickfix gel is good for use on wood & porous surfaces (e.g terracotta pots) as it doesn’t soak into the surface like a liquid would. -Acetone ( most nail polish remover) or Olive oil can also be used to remove Quick Fix from the skin. -Since Quick Fix cures with moisture, set times may be extended on very dry surfaces or under dry conditions. -Super glues cure more slowly when large amounts are used. For faster cure use sparingly. -While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbent material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use. Safety tips -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. -Do not use near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set -For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use -After use, wipe excess product from the nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. -Ensure cap is replaced and store in a cool dry place. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$3.78
Permanently joins metals, wood, plastics, ceramics, glass, vulcanized rubber, leather, fabrics, and plaster Pliobond sets fast, is Permanent Stays flexible and won't become brittle
$25.00
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER! PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour. Here are just a few specific uses (there are hundreds of other uses): Fasten galvanized steel to a concrete floor. Bond sheet metal to wood or masonry. Seal and insulate electrical connections and electronic boards. Protect electronic components from vibration and moisture. Repair porcelain or sculptures. Reattach multiple broken pieces in a vase. How to prepare a surface for bonding with PC-Clear™ Epoxy Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Clear™ Epoxy application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. FAQ Is PC-Clear™ Epoxy different from other clear epoxies? Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing. How does PC-Clear™ Epoxy’s strength compare to other epoxies? PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi. Is PC-Clear™ Epoxy brittle? PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies. How does outdoor exposure affect cured PC-Clear™? Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing. What is the best way to mix PC-Clear™? How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life. Why does PC-Clear™ Epoxy have a strong odor? The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing. Does PC-Clear™ Epoxy self-level? PC-Clear Epoxy™ is a liquid and is self-levelling. How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense? PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead. Can PC-Clear™ Epoxy be colored or tinted? PC-Clear™ Epoxy can be tinted.
$14.34
Parfix super glue is a fast setting cyanoacrylate-based adhesive that dries clear with a strong bond Instant strong bond Sets in 10 seconds Dries clear
$2.59
Parfix is a two-part epoxy adhesive designed to give high bond strength to most common household materials. Strong Bond Easy mix Rigid bond
$12.00
Parfix is a two-part epoxy adhesive designed to give high bond strength to most common household materials. Fast setting Easy mix Rigid bond
$11.94
Parfix everyday adhesive is an easy mix, two-part epoxy adhesive provides a strong, rigid bond, designed for use with most common household materials including china, metal, glass, leather, rubber, wood and most plastics. Fast setting Easy mix Rigid bond
$5.00
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted. Recommended For Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fibreglass composite, china, stone, marble and many rigid plastics Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete Not Recommended For Potable water systems. Applications above 121°C (250°F). Polyethylene and polypropylene. Structural applications. Safety Precautions Wear gloves. Preparation Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed. Application Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted. Cleanup Cured putty may be cut away with caution using a sharp blade.
$35.00
![Loctite Kintsuglue Flexible Putty 3 x 5g [Black]](http://gluesaustralia.com.au/cdn/shop/files/5010305059165_7b1ca3d2-d36e-4090-b9b6-2eae8421c80d.jpg?v=1754715955&width=645)
![Loctite Kintsuglue Flexible Putty 3 x 5g [Black]](http://gluesaustralia.com.au/cdn/shop/files/5010305059165_048877d1-353e-447d-a42c-df19d2e12c4a.jpg?v=1754715955&width=645)
Kintsuglue is an amazing paste created to fix almost any broken object. Shapeable, strong and flexible after curing, it can be applied to all the things you want to repair, reconstruct, protect or enhance. It restores the functionality of objects and treats repair as part of an object´s life, rather than replacing them. Take it Clean your hands and make sure all surfaces are dry and free of dust and grease. Shape it Knead Kintsuglue for about 10 seconds and then give the paste the desired shape before applying. Apply it Apply the paste to the surface you want to bond or protect. You have up to 30 minutes to adjust it before it starts curing! To get the best result, let it harden overnight.
$19.86
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on Great for crafting projects Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone Can be combined with fiberglass cloth for a durable patch Properties High impact resistance: won’t crack when drilled Can be tinted to match surrounding materials Water resistant and can be used outdoors Does not shrink Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 40 to 60 seconds Quick completion of project HOW TO USE: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$7.91
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications. LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications. LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs. Universal instant adhesive gel Will not drip or run Non-wicking, especially suited to porous materials Perfect for all quick repairs Ideal for overhead application and vertical faces Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics Technical Information Colour Clear: Ultra Clear Fixture Time 5 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose Physical Form Gel Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F
$7.50
Bonds metals, ceramics, concrete, fibreglass, marble and wood. Syringe dispenser accurately measures equal amounts of resin and hardener to prevent wastage. Fast curing, cure commences in five minutes and reaches full cure in one hour. When cured, the bond is transparent and virtually colourless. Loctite 5 Minute Epoxy Adhesive's premium formulation is solvent-free and 100% solids providing a non-shrink, environmentally friendly bond. High viscosity provides a good gap-filling ability. DIRECTIONS FOR USE: 1. Surfaces must be clean and dry. If possible, roughen surface with sandpaper to improve keying and bonding. 2. Cut tips of twin nozzle with a sharp knife and remove nozzle cap from syringe plunger. 3. Push the twin plunger to squeeze out equal amounts of resin and hardener in the amounts required. 4. Mix the resin and hardener for one or two minutes until the colour is completely uniform. 5. Apply immediately to both surfaces and press together. Pressure clamping is not necessary, but allow the adhesive to set for at least 5 minutes before moving. Remove any excess adhesive immediately. 6. Important. After dispensing product be certain to insert plug supplied in the nozzle of the syringe to prevent waste. Preferably store in an upright position as packaged. Structural Bonding - Fast Cure. Sets in 5 minutes. Sets in 5 minutes. Good chemical resistance. Fixture time: 4-6 min Temperature Resistance: Up to 180°F (82°C)
$15.11
PlasticWeld is a specially formulated two-part adhesive and epoxy filler system that provides for strong, lasting repairs. PlasticWeld will bond a variety of surfaces, such as metal, composites, fiberglass and others. PlasticWeld sets in 5 minutes at room temperature and is fully cured in 1 hour. Using a 1:1 mixing ratio, PlasticWeld combines to a tensile strength of 3200 PSI and cures to an off-white color. GREAT FOR Most Hard Plastics ABS Fibreglass PVC Glass Vinyl STRENGTH 3200 PSI SET TIME 5 Minutes CURE TIME 1 Hour CURE COLOR Off White USE ON Automotive Ceramic Epoxy & Adhesives Fibreglass Plastic/Composite/PVC And More
$14.95
PlasticWeld is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. *After mixing, it forms a polymer compound that can be moulded or used to build up and repair just about anything made from plastic. When cured, it can be sawed, drilled, carved, sanded and painted. PlasticWeld has a 20-25 minute work life; functional cure occurs in 2-3 hours. PlasticWeld cures to an off-white colour, is rated at a tensile strength of 350 PSI. Does not adhere to polyethylene, polypropylene or some other plastics. Test for adhesion first. GREAT FOR Rigid & Semi-flexible Plastic ABS, PVC & CPVC Pipes Automotive Trim & Bumpers Fibreglass Parts Vinyl Siding STRENGTH: 350 PSI SET TIME: 25 Minutes CURE TIME: 3 Hours CURE COLOR: Off White Drinking Water Safe USE ON Automotive Ceramic Epoxy Putty Sticks Fiberglass Plastic/Composite/PVC And More
$21.00
PlasticBonder™ is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. PlasticBonder™ has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder™ sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Fibreglass Plastic/Composite/PVC Wood And More PREPARE Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. MIX After removing the replaceable cap, press down on the plunger and squeeze equal amounts onto a disposable surface and mix thoroughly. APPLY Apply with appropriate tool in an even coat, weld bead or extruded shape as needed. DRY Sets in 15 minutes. Cures in 30 minutes. If the temperature is below 40ºF, then set time is longer.
$18.00
Plastic Bonder is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. Plastic Bonder has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, Plastic Bonder sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Epoxy & Adhesives Fibreglass Plastic/Composite/PVC Wood And More
$19.95
KwikWeld™ is a fast-setting version of The Original J-B Weld two-part epoxy cold weld system that provides strong, lasting repairs to metal and multiple other surface types. After mixing, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. KwikWeld™ has a 1:1 mixing ratio, sets in 6 minutes and is fully cured in 4-6 hours. KwikWeld™ cures to a dark grey color, is rated at a tensile strength of 2424 PSI and will withstand temperatures up to 300ºF. GREAT FOR Household Repairs Automotive Plumbing Marine Crafts & More USE ON Automotive Brick Ceramic Concrete And More
$16.00
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$22.51
GorillaWeld is an incredibly strong, heavy duty two-part adhesive. The tough, steel bond epoxy formula has a 4250 PSI bond strength and sets in just 10 minutes. GorillaWeld is waterproof and versatile, creating a long-lasting, permanent bond to metal, plastics*, concrete, ceramics, PVC, fibreglass and more! Features: INCREDIBLY STRONG: 4250 PSI STEEL BOND EPOXY SETS IN 10 MINUTES WATERPROOF** FORMS PERMANENT BOND DRIES DARK GRAY EASY TO USE BONDS: Metal, Plastic*, Concrete, PVC, Fiberglass, Ceramic & More! *Not recommended for use on polyethylene or polypropylene plastics. **Bonded wood materials should not be submerged or soaked in water. Directions All surfaces should be clean and free of debris. To improve adhesion, roughen smooth surfaces with sandpaper before gluing. Remove cap from each tube and use top of cap to puncture foil seal. Dispense equal parts from each tube onto a clean, disposable surface. Mix with disposable mixing tool for approximately 20 seconds until the colour is uniform. Apply mixture to surface within 3 minutes. Clamp surfaces together and leave undisturbed for 10 to 30 minutes. Full cure in 24 hours. Cure time dependent on temperature, humidity and quantity applied. *Note: Not recommended for use on polyethylene, polypropylene or similar plastics. Specs: APPLICATION TEMPERATURE: 32°F to 90°F SERVICE TEMPERATURE: -40°F to 300°F SET TIME: 10 minutes CURE MECHANISM: 2 Part Reaction, requires mixing OUTDOOR: Yes FREEZE/THAW STABLE: Yes WATERPROOF: Yes* PAINTABLE: Yes SANDABLE: Yes DRILLABLE: Yes SHAPEABLE: Yes STAINABLE: No CHEMICAL RESISTANT: Limited EXPANDS WHEN CURED: No SHRINKS WHEN CURED: No CURED COLOR: Dark grey GAP FILLING: Yes *Not suggested to use on wood materials submerged or soaked in water Will GorillaWeld bond plastic/vinyl/rubber? Gorilla Weld will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP), polyethylene (PE) or similar plastics, or any type of rubber with high oil or plasticizer content. What does GorillaWeld work best for? GorillaWeld is ideal for metal and plastic (see above) substrates. GorillaWeld does not sag so it is ideal for vertical surfaces How should GorillaWeld be stored? GorillaWeld should be stored in a cool, dry place. Store away from children and animals. How do I mix GorillaWeld? GorillaWeld should be mixed 1:1 for 20 seconds or until uniform prior to application. Does GorillaWeld become hot during cure? Yes, mixing the hardener and resin together creates an exothermic reaction and will generate heat during cure. Consideration should be taken on mixing vessel as not to melt. How long do I have before GorillaWeld begins to harden? GorillaWeld will begin to harden after 3 minutes. Adhesive should be applied prior. What surfaces will GorillaWeld bond to? GorillaWeld is particularly suited for metal, plastic and other rigid surface bonding. Is GorillaWeld Food Safe? GorillaWeld is not recommended for direct or indirect food contact and should not be considered food safe. Why is GorillaWeld odour so strong? GorillaWeld is based on methyl methacrylate chemistry which has a naturally strong odour. We suggest using in a well-ventilated area. How do I remove GorillaWeld from body/skin? Uncured: GorillaWeld can be harmful through skin absorption and it is strongly recommended that you wear gloves during use. If GorillaWeld is on the skin, try removing with a dry cloth or paper towel and then wash the area thoroughly with soap and water. Cured: Cured material can be rolled off the skin. Remove as much cured material as possible and wash the area thoroughly with soap and water. For medical emergencies, call 1-800-420-7186 anytime How do I remove GorillaWeld from my surface? Uncured: Wipe up as much material as possible with a dry cloth and clean any remaining product/residue with Isopropyl alcohol (IPA) or acetone following solvent manufacturer’s instructions. Cured: For removing cured/dried GorillaWeld, mechanical means such as sanding or chiselling. What should I do if I think a human or animal has ingested GorillaWeld? For medical emergencies, call 1-800-420-7186 anytime
$15.82
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless. Features: Dries Clear: Ideal for clean, easy finishing 5 Minute Set: Plenty of repositioning time for the perfect fit. Gap-Filling: Fills voids and bonds uneven and vertical surfaces. Water Resistant: Withstands moderate exposure to water Solvent resistant Non-Toxic once cured Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses. Directions Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Prepare Your Work Area and the Surface If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Mixing Gorilla Epoxy Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio. Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine. Application After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. Clamping To reach maximum bond strength, clamp project together and leave undisturbed. Important Cure Times Set: 5 minutes to apply and position Handling: Allow to cure for 30 minutes undisturbed (no weight or handling) Final Cure: Allow 24 hours for load-bearing weight Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more. FAQ Is Gorilla Epoxy gap filling? Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight. What is the shelf life? Are there storage tips to extend the shelf life? Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix. What is the best application temperature? For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time. Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C Do I need to use clamps with Gorilla Epoxy? How long? Clamps are recommended for use during setup to ensure the bond sets correctly. Set Time: 5 minutes to mix, apply and position Handling Time: Leave 30 minutes undisturbed (clamping is recommended) Full Cure Time: 24 hours for load-bearing weight How much Gorilla Epoxy do I apply? Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond. Average coverage from our 25 mL epoxy syringe will cover 100 square inches. What can I use as a mixing tray or stir stick? A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing. What is Gorilla Epoxy? Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results. How do I remove Gorilla Epoxy? Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding. Uncured Removal: Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps. Hair: Isopropyl alcohol Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric. What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more! What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®. How do I dispense Gorilla Epoxy? Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
$17.25
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$6.50
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$4.50
Overview Tired of unreliable glues that fall apart? Meet our game-changing Epoxy Adhesive, a powerhouse in bonding technology. In just a single 25mL package, this epoxy adhesive promises unparalleled durability and convenience. It dispenses effortlessly, ensuring a precise ratio for maximum strength. With a fast-acting formula that's perfect for bonding a variety of materials, your DIY or repair projects just became hassle-free! Features Automatic Self-Mixing Nozzle No more guesswork! Our self-mixing nozzle automatically dispenses epoxy and hardener in the exact ratio for optimal performance. Fast Setting & Long-Lasting Sets in just 5 minutes. Can be safely handled within 30 minutes. Attains full strength after 16 hours. Versatile Usage Ideal for bonding ceramics, glass, leather, wood, plastic, and metal. Your go-to solution for a myriad of projects. Superior Formulation 50% Epoxy Resin 50% Modified Amine Produces a high-strength bond resistant to temperature fluctuations between -40°C and 80°C. How to Use Preparation Safety First: Always wear protective gloves and safety glasses. Surface Preparation: Ensure the surface is clean, dry, and free from dust, oil, and grease. Application Air Removal: Hold the dispenser, nozzle end up, for 30 seconds to release entrapped air. Cut the tip carefully. Dispensing: Press the plunger slowly to dispense equal parts of resin and hardener. Mixing: Mix thoroughly before applying. Bonding: Apply adhesive to the surface and hold until set. Use tape or clamps if necessary. Post-Application Cleanup: Use acetone for cleaning. Storage: Store in a cool, dry place with the nozzle end up.
$9.95
Bostik Super Glue is a multipurpose glue that bonds most non-porous materials in seconds. It dries to a clear, permanent bond with exceptional tensile strength up to 210 kg per square cm. Recommended Uses: -Precision work -DIY projects -Home handyman projects -Electrical -Optical -Watch -Jewellery -Car accessories -Materials Designed to stick: -Metal -Ceramic -Wood -Most plastics - (not polyethylene or polypropylene) -Natural and synthetic rubber -Leather Features: -Dries clear -Exceptional tensile strength up to 210kg per square cm -Enables precision work due to its small size
$5.20
Fast, strong and resistant super glue gel Product overview Bostik Fix & Glue Gel is the latest technology available in the market, which sticks in a few seconds and provides a strong, long-lasting bond. Its gel consistency makes it suitable for vertical surfaces. It is easy to use through its precise nozzle, in which the product will remain liquid for up to 12 months. Most importantly, Fix & Glue Gel is solvent-free and odourless – making it a safer option. Product Details Flexible and durable bond resists knocks and drops Water & temperature resistant Solvent-free Non-irritant, and odourless No respiratory allergens Recommended Uses Bostik Fix & Glue Gel is a great repair solution, in particular for vertical surfaces. Bonds almost all materials, including: Porcelain Ceramic Glass Mirror Leather Wood Paper Metal Fabric Hard plastic Tiles Concrete Brick Stone
$3.99
Fast, strong and resistant super glue gel Product overview Bostik Fix & Glue Gel is the latest technology available in the market, which sticks in a few seconds and provides a strong, long-lasting bond. Its gel consistency makes it suitable for vertical surfaces. It is easy to use through its precise nozzle, in which the product will remain liquid for up to 12 months. Most importantly, Fix & Glue Gel is solvent-free and odourless – making it a safer option. Product Details Flexible and durable bond resists knocks and drops Water & temperature resistant Solvent-free Non-irritant, and odourless No respiratory allergens Recommended Uses Bostik Fix & Glue Gel is a great repair solution, in particular for vertical surfaces. Bonds almost all materials, including: Porcelain Ceramic Glass Mirror Leather Wood Paper Metal Fabric Hard plastic Tiles Concrete Brick Stone
$9.21
Bostik Super Glue is a multipurpose glue that bonds most non-porous materials in seconds. It dries to a clear, permanent bond with exceptional tensile strength up to 210 kg per square cm. Recommended Uses: -Precision work -DIY projects -Home handyman projects -Electrical -Optical -Watch -Jewellery -Car accessories -Materials Designed to stick: -Metal -Ceramic -Wood -Most plastics - (not polyethylene or polypropylene) -Natural and synthetic rubber -Leather Features: -Dries clear -Exceptional tensile strength up to 210kg per square cm -Enables precision work due to its small size
$4.98
Bostik Soft Plastics Adhesive is a strong water-resistant polyurethane-based adhesive, designed for long-lasting repairs of objects made from common soft and flexible plastics. It is quick-drying leaving a clear and almost invisible glue line. Ideal for repair of inflatable swimming pool toys. APPLICATIONS Repair of inflatable toys, plastic raincoats, lilos and vinyl swimming pools. Also suitable as a general-purpose glue for DIY repairs around the house and for arts and craft. ADHESION Adheres to rigid and soft (plasticized) PVC, ABS, Perspex, Polystyrene (solid), Formica polyurethane, and fibreglass. Also bonds a variety of other materials such as metal, glass, porcelain, ceramic, leather, most rubbers, felt, cork, fabric, cardboard, paper, coated and uncoated wood. LIMITATIONS - Not suitable on plastics such as polypropylene, polyethylene. - Not suitable on expanded polystyrene, rayon and acetate fabrics, EPDM and silicone rubber. SURFACE PREPARATION Surfaces must be clean, dry and free from all loose materials, dust, dirt, oil, rust and any other contaminants. For improved adhesion, surfaces should be lightly abraded and then wiped with a solvent such as acetone. Poor surface preparation may result in a weak bond and delamination of the substrates along the glue line. HOW TO USE 1. Ensure that surfaces are prepared as above. Wet stick method: 2. Spread an even film of adhesive onto both surfaces. If required, use the PVC patch provided. 3. Leave the surfaces open for approximately 5 minutes, until almost dry. 4. Bring surfaces together firmly until bonded. If necessary, hold together with a clamp or tape. 5. Full strength develops after 24 hours. Dry stick method: 6. This application method achieves the strongest and fastest bond. It is ideal for heavy-duty repairs or when initial high bond strength is required. 7. Spread an even film of adhesive onto both surfaces. Allow drying completely. 8. Re-activate the glue by applying a suitable heat source over the surfaces, e.g. a hairdryer. 9. Once the surfaces are very hot, bring together and press firmly to ensure good contact for about 2 minutes. 10. Depending on the application, the object may be handled immediately. 11. Full strength develops after 24 hours. CLEANING - Wet adhesive can be cleaned with acetone. - Dried adhesive can be removed mechanically or with acetone. If using acetone, check for substrate compatibility prior to use. PRODUCT CHARACTERISTICS Type Polyurethane Appearance Clear viscous liquid Density (g/cm³) Approximately 0.9 Odour Mildly pungent odour Solids (%) Approximately 15 Viscosity (cps) Approximately 3500 TYPICAL PERFORMANCE DATA Initial setting time 10 minutes to 2 hours (depending on porosity of substrate) Final setting time 24 hours Temperature resistance Approximately -20 to 80°C Water resistance Excellent
$7.04
Bostik Multi Bond is a general purpose solvent based Nitrile Rubber Adhesive. It is nearly clear in colour and will give excellent bonds that are both chemical and temperature resistant. It is packaged in a convenient aluminium tube for ease of use. Where to Use Residential Commercial Industrial Substrates Toys Leather Goods Furniture Upholstery Jewellery Materials Leather Metals Wood Canvas PVC Plastics Features Quick bonding Easy to use Chemical and temperature resistant It has many household and industrial uses and is particularly suitable for bonding leather, metals, wood, canvas PVC and other plastics. It is widely used in the repair of toys, leather goods, furniture, upholstery, jewellery and in the handicraft making areas. This is an excellent product where quick bonding and a clear bond line is required especially in the DIY market. Instructions Surface Preparation Surfaces to be bonded must be dry, clean and free of grease. If surfaces are non-porous, smooth and glossy, roughen with glass paper (preferably) or apply solvent suck as Acetone As a two way dry stick: Apply an even film onto both substrates, leave 5-10 minutes then join together with as much as possible taking care not to trap any air. As a one way wet stick: Usually, this technique is employed when either one or both of substrates to be bonded are porous (e.g. fabrics, cardboard). Clean Up Any wet or partially wet adhesive can be removed with scraping and Bostik Solvent 9901. The dried adhesive is best removed with a scraper or by sanding. STORAGE AND SHELF LIFE A minimum of 12 months in original sealed packaging if stored under cover away from heat.
$9.95
DESCRIPTION Bostik Hard Plastics Adhesive is a solvent-borne adhesive based on SBS polyurethane. It has the advantages of easy application, by comb or brush and immediate strength on contact. YOUR SMART ADVANTAGES - Clear and water-resistant - Easy to apply - Immediate strength on contact - For tough repairs USES Bostik Hard Plastics Adhesive is suitable for bonding the following plastics to themselves and each other: PVC-U, ABS, High Impact Polystyrene. It has wide range of uses for repairing household objects. Bostik Hard Plastics adhesive is also useful for sticking most clear plastics, wood, metal and leather. PRODUCT CHARACTERISTICS Colour Transparent Form Mobile liquid Specific Gravity 0.92 approx. Composition Synthetic resin Viscosity Low Solids Content 27% approx. Odor Ketonic PREPARATION 1. Make sure all surfaces to be bonded are clean and dry, free from dust, dirt and grease. APPLICATION 2. Remove tube cap and spread the adhesive evenly over both surfaces. 3. Leave the coated surfaces until the adhesive is just tacky, approximately 4 minutes at normal room temperature. 4. Ensure the surfaces are accurately aligned and then press firmly together. They will stick immediately. CLEANING 5. After use, wipe the nozzle with a clean dry cloth (avoiding skin contact). 7. Bostik Hard Plastics adhesive can be removed using acetone before set. Solvents can damage some surfaces, therefore carry out a test on a small area first. PRECAUTIONS IN USE Bostik Hard Plastics adhesive is not suitable for polyolefins e.g. polythene, polypropylene or PTFE. It should not be used for repairing items that hold hot liquids.
$7.04
Bostik Epoxy Bond is a special two-part adhesive which, when mixed and allowed to set, produces bonds of immense strength. This resin based epoxy sets in approximately 5 minutes to give a permanent and colourless bond. It will adhere to pottery, china, metals, glass, wood, rigid and semi-rigid plastics and cardboard, etc. where an Industrial strength bond is required by handymen, hobbyists and tradesmen. FEATURES AND BENEFITS 1. Quick setting – will bond in 5 minutes 2. When fully cured, the adhesive can withstand boiling water for short periods of time. 3. Heat resistance rating of 60ºC temperature continuously. 4. Adhesive shear strength of up to 800 psi for metal/metal bonds APPLICATION 1. Surfaces to be joined must be clean, dry and free from dirt and grease. Metals should be abraded and washed with a petroleum solvent. China and pottery should be washed in detergent, rinsed and dried. 2. Dispense and mix thoroughly, sufficient material of the two parts to carry out the job at hand with a matchstick, screwdriver or similar implement. Reseal the nozzles of the syringe with the enclosed plug and tube with cap and store in an upright position (nozzles upward). 3. Apply a thin film of adhesive to one or both of the surfaces to be joined, press together and do not move until the adhesive has set - usually 5 minutes @ 20ºC. Very good handling strength is obtained after 20 minutes and maximum adhesion is achieved after 24 hours
$9.00
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product: General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$13.17
A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts. -Bonds a variety of surfaces -Dries Crystal Clear so there’s no visible evidence of repair -Quick setting in 5 minutes -No clamping necessary -High water resistance -Forms a rigid, durable bond -Can be used for gap filling (Surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Doesn’t yellow over time so is ideal for use on glassware Appearance: Crystal Clear Where can this product be used? -Fixing a broken glass vase -Repairing jewellery -Toy repairs -Fixing ornaments or crockery -Fixing your handbag strap -Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene -What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic – refer to Selley's plastic guide for more info -Crystal -Leather How to use this product: -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. -When using tube kit, ensure correct caps are replaced on each tube or they will adhere. Handy tips: -A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). -Clamping is recommended for a stronger bond. -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set. Storage and re-use: Ensure caps or lids are replaced and product stored in a cool dry place.
$16.58
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$28.96
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$16.00
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$11.05
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.00
You have seen 91 out of 91 products
Adhesives tagged for plastic repair, suited to cracked housings, trims, toys and fixtures. Compare instant cyanoacrylates for close-fit parts with gap-filling epoxies for structural fixes. For glossy or contaminated plastics, clean/degrease and lightly abrade before bonding. Some plastics may still need primers/activators, see product notes. Use filters to refine by set speed, clarity, flexibility and application method. Always review the product page and TDS/SDS for prep and cure guidance.
