UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$18.00
Red, permanent Thread Locker prevents loosening by filling in the inner spaces in threaded metal parts to form a tough solid assembly. Pacer Technology Super Glue Red Threadlocker (15191) is a high strength premium grade product used to permanently lock or seal metal threaded components or for metal fasteners up to 1” in diameter. Also prevents loosening due to high vibration. Appearance – red liquid with mild odour. Use Instructions: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow curing 24 hours for maximum strength. The excess adhesive on the outside of parts will not cure and can be removed with a solvent-soaked cloth. Storage and shelf life: Recap for storage. A one-year shelf life can be expected. CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$9.95
Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists.KEEP OUT OF REACH OF CHILDREN.
$12.50
Tarzan's Grip Shockproof Super Glue is a high strength, rubber toughened adhesive that dries clear for a multitude of applications. In addition to offering a superior bond on metals, it is ideal for use with wood, rubber, leather, china, paper and most plastics. It resists extreme temperatures of up to 150C. Sets in around 2 to 3 minutes Impact resistant Heat resistant Superior bond on metals
$10.44
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
Sika AnchorFix®-1 is a high-performance, styrene-free chemical anchoring adhesive designed for fast and reliable installations in both construction and DIY projects. This two-component, solvent-free, polyester-based adhesive is ideal for securing rebars, threaded rods, bolts, and special fastening systems in concrete, hollow and solid masonry, hard natural stone, and solid rock. It cures rapidly, even in low temperatures, and can be applied using standard guns. Advantages: Fast curing Compatible with standard guns Usable in low temperatures High load capacity ETA approved Non-sag, even overhead Styrene-free Low odor and wastage Technical Information: Compressive Strength: ~60 N/mm² (7 days, +20°C) Modulus of Elasticity in Compression: ~3,500 N/mm² Tensile Strength in Flexure: ~28 N/mm² Tensile Strength: ~12 N/mm² Temperature Resistance: +50°C (long-term), +80°C (short-term) Glass Transition Temperature: +60°C Color: Component A: White Component B: Black Mixed: Light grey Usage: Ideal for various grades of rebars, threaded rods, bolts, and special fastening systems. Substrates may vary, so testing is recommended to ensure suitability, especially with natural stones. Always ensure the substrate is clean, dry, and free of contaminants. Perform pull-out tests if the substrate strength is unknown. Mixing and Application: Mix the components in a 10:1 ratio by volume. The material must be between +5°C and +40°C for application. Ensure the substrate temperature is between -10°C and +40°C. Shelf Life and Storage: Shelf life is 12 months from the date of production when stored properly. Store in unopened, sealed, and undamaged packaging in dry conditions between +5°C and +25°C. Curing Times: +30°C: Open time 4 minutes, Curing time 35 minutes +25°C: Open time 4 minutes, Curing time 40 minutes +20°C: Open time 5 minutes, Curing time 50 minutes +10°C: Open time 6 minutes, Curing time 85 minutes +5°C: Open time 10 minutes, Curing time 145 minutes -10°C: Open time 30 minutes, Curing time 24 hours Approvals and Certifications: Complies with NCC 2019 reference to AS 5216:2018 for post-installed and cast-in fastenings in concrete. ETA-approved for use in masonry and non-cracked concrete, with CE marking. Cleaning of Equipment: Clean tools with Sika® Colma Cleaner immediately after use. Hardened material can only be removed mechanically. For detailed design considerations, refer to "Technical Documentation Sika AnchorFix®-1" (Ref: 870 43 01).
$38.30
Selleys Urethane Bond Is a high strength shock proof, water and chemical resistant polyurethane adhesive. Features High strength Achieves maximum bond in 48 hours Shockproof Flexible, shatterproof and impact resistant so it can take knocks Durable Lasts a long time Chemical resistant Wont break down by temporary exposure to most chemicals i.e. solvents Waterproof and weatherproof Good for bonds exposed to the elements When curing, Urethane Bond expands, filling voids and strengthening the bond Easy to use Requires no mixing, ready to use straight from the pack Only need to apply adhesive to one surface Versatile Can be used inside or outside Sandable and paintable after dries
$25.00
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$9.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7ce782d52b264c1db0e928662698e299.jpg?v=1757753227&width=645)
$16.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/51345fd2ddf64a74a03e2c6b9e0d7e1a.jpg?v=1757753232&width=645)
$17.26
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/81e21d7d520d41a280976d39a403b5c9.jpg?v=1757753238&width=645)
$16.00
Flexiseal FC is a fast curing polyurethane Adhesive and Sealant with high flexibility and excellent adhesion. Waterproof+, suitable for indoor and outdoor applications^, paintable after it has cured. Best for : Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. Product Details Where can this product be used? External wall and cladding joints Weatherproofing joints between brickwork, masonry, wood concrete or metal frames Joints in walls, balconies, around window or door frames Joints in bridge and balcony parapets Retaining walls Roofing Acoustic rated walls What materials is this product suitable for? Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. How to Use AS AN ADHESIVE: Apply a bead or small blobs on surface. Assemble parts together and clamp firmly to hold until cured. Remove excess immediately. Initial bond achieved in 24 hours depending on temperature and humidity. Bond strength increases over a few days. AS A SEALANT: Extrude sealant into the joint ensuring full contact with the sides of joint. Avoid entrapment of air. Smooth sealant with spatula forcing it into the joint. For best performance, install joint backing rod (polyethylene or polyurethane foam rod) in the joint to control depth and ensure joint movement. Suitable for +/- 25% joint movement. Complies with ISO11600/F/25HM. Limitations: *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. ^To maximise durability in outdoor applications paint with a suitable exterior paint. Some colours may discolour after exposure to UV radiation. +Not suitable for permanent water immersion or below water line use. Clean Up Mineral turps. Cured product can only be removed mechanically
$19.00
D-MASTIC is an oil-based sealant that forms a skin on exposure to air but remains soft underneath. Designed for sealing windscreens in cars, boats, trucks, and buses, and for metal lap joints in white goods, caravans, bus and truck bodies. Features Forms a surface skin, preventing transfer by touch and dirt pick-up on exposed surfaces Paintable with most alkyd and water-based paints (after the skin has formed). Easy clean-up off non-porous surfaces with mineral turpentine. Convenient to use non-slumping from vertical joints and easily extrudable. Long "open" time assists in the assembly of lap joints. Where can this product be used? Metals Paintwork Lacquered Work Machinery and Engines Sealing windscreens Metal lap joints in whitegoods and automotive bodies What materials is this product suitable for? Metal Glass Painted Surfaces Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as mineral turps. Cut nozzle supplied at an angle and to the required opening. Cut tip off cartridge, fit nozzle and insert in suitable caulking gun such as Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply D-Mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps or kerosene. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Maximum service is achieved when used within joints; it is not recommended to be used as a"skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with a spatula dipped into mineral turps. Uncured product may be removed with mineral turps or kerosene. Cured product can be removed by cutting and scraping.
$21.55
![Selleys Butyl Mastic Rubber Caulking Compound for Vehicles [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697101495_09a144af-33d1-46e0-9c47-6910c6f2672a.jpg?v=1754711927&width=645)
Selleys Butyl Mastic is a synthetic resin, butyl rubber based mastic which forms a smooth tough skin, but remains permanently plastic underneath. It is available Off White. Features Remains permanently plastic under a smooth tough skin Versatile sealant with excellent adhesion to a variety of substrates without the necessity to prime Will not bleed into porous surfaces Non-sag in joints up to 12mm vertical joint Wide service temperature: –35° to +65°C Excellent weathering characteristics Does not corrode metals Good water resistance Life expectancy is approximately 5 years in a thick joint. It is recommended to use silicone sealant in thinner joints Easy smoothing and clean-up with mineral turps or white spirits Where can this product be used? Sealing aluminium windows to masonry. Sealing joints between pre-cast concrete panels or porcelain enamelled panels. Sealing edges of all types of wallboards or wherever a permanent waterproof seal is required. Sealing lap joints between metal applications with the inclusion of fasteners. Ideal for dust proofing cars, trucks, caravans, boats, etc. and is suitable for sealing cracks and gaps around brickwork, roofing and cladding. What materials is this product suitable for? Please contact your store to confirm avaliability, as some stores may have a limited range. The following should only be used as a guide and the installer should apply all Australian Standards, BCA/NZBC requirements, and best practices when installing. Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as white spirits. Cut nozzle supplied at an angle and to the required opening. Cut end off nipple on cartridge, fit nozzle and insert in suitable caulking gun such as the Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of Butyl Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply Butyl Mastic by forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Should not be used where joint movement will exceed ±8%. Maximum service is achieved when used within joints; it is not recommended to be used as a "skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. Surfaces must be clean and dry. Life expectancy in joints is approximately 5 years Interior applications may have greatly extended skin over time due to the reduced presence of sunlight. Allow surface to skin before painting, i.e. approximately 24 hours after application. Butyl Mastic can be painted over using oil or water based paints after the surface has skinned.
$33.47
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
![Selleys Armour Flex High Performance Adhesive [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125262_5e542168-6518-4fbd-97ab-586ab182d6e9.jpg?v=1754711932&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
![Selleys Armour Flex High Performance Adhesive [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125293_a1f282bb-e154-4d4c-812a-1cc8034e1e80.jpg?v=1754711935&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$23.14
![Selleys Armour Flex High Performance Adhesive [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125286_24a1028f-4655-4200-8859-8e45b8c9ab19.jpg?v=1754711936&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$20.00
Selleys Seal Fix forms gaskets/seals directly from the tube; any size, any shape. Selleys Seal Fix cures to a tough durable silicone rubber, and is ideal for repairing or replacing worn our seals in domestic ovens, fridges and freezer doors, as well as automotive and appliance gaskets. Seal fix is resistant to chemicals, oil, water, detergent etc. It is safe for incidental contact with food. Features: -High-Temperature resistance up to 260°C** -Durable clear rubber seal -Ideal for vertical applications -Impact resistant -Safe for incidental food contact. Where can this product be used? -Replacing oven door seals -Replacing refrigerator door seals -Dishwasher door seals -Washing machines -Automotive gaskets and seals -Heating and air conditioners -Flanges of all kinds What materials is this product suitable for? -Metal* -Paint/coated surfaces -Glass -Fibreglass How to use this product -Clear surfaces with Selleys BBQ Tough Wipes or Oven Wipes and allow to dry. -Pierce tube seal, fit nozzle and cut to size. -For repair or replacement of oven door seal or oven door glass: Apply Seal Fix to repair or replace seal or glass. -Once the seal or oven glass is fixed in place the repair should be allowed to cure for 7 days before using the oven. -For repair or replacement of refrigerator door seal: Apply Seal Fix to door, bring surfaces together and close door. -Once the seal is glued in place the door needs to be held firmly closed with tape. -Due to the strong magnetic hold of the door seal to the refrigerator body, the repair must be allowed 24 hours to cure before opening the door or subjecting to any stress For repair or replacement of gaskets: -Remove old gasket/seal material and thoroughly clean surfaces with mineral turpentine and dry. If adhesion of gasket is not required wipe mating surfaces with an oily cloth. -Pierce seal in the tube, fit nozzle and cut to size. Squeeze the bead of sealant onto one of the surfaces to be joined, around the perimeter of the part and around bolt holes. -Join parts together within 10 minutes and bolt down to the desired torque. If a thicker gasket is required assemble but do not tighten bolts for 24 hours. Material cures in 24 hours. (When disassembly is required, pry two flanges apart and remove old sealant before reassembly.) Clean Up -Uncured product may be removed with mineral turpentine. Cured product can be removed with Selleys Silicone Remover or by mechanical action. Handy tips -When eliminating cork gaskets, ensure that adequate clearance remains for mechanical parts e.g. valve rocker covers (do not fully tighten until sealant has cured) Limitations *Not for copper brass or galvanised metal surfaces **Not suitable for continuous exposure to temperatures above 205°C or intermittent (more than 2 hours) expose to temperatures above 260°C Not for exhaust manifold or for contact with gasoline or distillate Safety tips -Avoid contact with skin and eyes and breathing vapour -On contact, the uncured sealant can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice -May irritate sensitive skin. If skin contact occurs, wipe off immediately and wash with plenty of soap and water -Ensure use in a well-ventilated area -Product releases acetic acid while curing -For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764 766) or a doctor -For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site Storage and re-use -Store in a cool, dry, well-ventilated place and out of direct sunlight -Keep containers closed when not in use – check regularly for leaks
$13.00
Holds up to 13.6kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 1.2 cm Overall Width (Metric) 5 cm Product Colour Black Product Type Rolls Size 5cm x 1.2m Details For your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.6kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for Drywall Waterproof once bonded to surface Uses 3M VHB™ Tape, Extreme strength and high conformability
$17.19
Holds up to 5.4kg, 17cm holds 1kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 2.5 cm Overall Width (Metric) 7.6 cm Product Colour Black Product Type Strips Size 2.5cm x 7.6cm Details For your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 5.4kg, 17cm holds 1kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for Drywall Waterproof once bonded to surface Uses 3M VHB™ Tape, Extreme strength and high conformability
$11.29
![RiteTack Instant Grab Construction Adhesive 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/0799439671669_6c8563d0-64cb-499e-a564-d2d4a62e9ce2.png?v=1754712007&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/0793591712994_c9bef70a-42d0-408c-8b14-e176578d110d.png?v=1754712009&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/0793591712987_0ace0873-9628-42fc-9b06-c64c93c74c40.png?v=1754712010&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
Ultra-High strength supa glue that dries clear. Gives great strength as well as flexibility and heat resistance. Performance above and beyond normal Supa Glue. Features Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve an initial bond Self-piercing, clog-free cap Forms a strong, flexible bond Impact Resistant – 4 times greater impact resistance than normal supa glues Superior bond on metals – up to 6 times stronger bond on steel than normal supa glue. Up to 4 times stronger bond on aluminium than normal supa glues Heat Resistant to 120°C permanently, 150°C intermittently Comes with a nozzle for easy, accurate application Appearance Clear thick liquid dries to a colourless film. Where can this product be used? Ideal for small repair jobs or when immediate results are required Fixing a broken door knocker Refixing wooden or metal door handles Repairing crockery safe to put in the dishwasher Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or other materials containing alkaline elements Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals Wood China Rubber Leather (test first as leather may become hardened or discoloured) Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Refer to handy hints for cleaning tips. Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. Allow 12 hours for sufficient bond strength for practical use. Handy tips Supa Glue can create a white residue on the surface of materials if the area is not well ventilated. Clean the affected area with acetone to remove (most nail polish removers) residue. Excellent when used with other adhesives, as the temporary tack. For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. In the event that fingers get stuck together – don’t panic! Slowly twist fingers in the opposite direction in hot soapy water. Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from the skin. While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin is soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary to apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. Do not use near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$7.00
An all purpose, high strength household glue that unlike standard superglues is extremely ‘infinitely’ more flexible. It can repair and bond a variety of surfaces and withstand the most extreme/rough conditions whilst providing the ultimate bond. Features Strong Bond Ultra Flexible – infinitely more flexible* Extreme Resistance to: Shocks & Vibration, Torsion & Movement, Water and Extreme Temperatures Dishwasher Safe Gap Filling (works on uneven surfaces) Paintable Adjustable for 1min Non-Drip (great for vertical surfaces) Interior/Exterior Easy to use Heat resistant -15°C to +120°C Solvent free, no shrinkage Colour Dries translucent What materials is this product suitable for? Metal Wood Glass Rubber China Leather Ceramics Masonry Fibreglass Vinyl Cardboard Fabric Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place Safety Tips On contact, uncured adhesive can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice. Avoid contact with skim. If contact occurs, wipe off and wash with detergent. Avoid breathing vapours. Use in a well ventilated area
$12.00
Permanently joins metals, wood, plastics, ceramics, glass, vulcanized rubber, leather, fabrics, and plaster Pliobond sets fast, is Permanent Stays flexible and won't become brittle
$25.00
Multi-use liquid super glue Water-resistant, dishwasher, shock and temperature resistant Bonds in seconds Strength to withstand heavy loads Dries transparent Product Marketing Has the handle of your favourite mug broken off? Are you looking for a strong glue to mend precious china? Look no further than Loctite Universal Super Glue! This multi-purpose glue helps you to easily handle any kind of small daily repair job around the house! Providing instant strength, transparent drying technology, and an anti-clog cap, Loctite Universal ensures durable, long-lasting, and invisible repairs. This practical, transparent glue works on a variety of materials - from wood, rubber, plastic, and more - it even works as a leather glue. Thanks to its self-piercing anti-clog cap, the repair glue is super easy to use and does not dry out, ensuring long-term reusability. This instant glue not only withstands heavy loads but is also shock-resistant and serves as a waterproof and heatproof glue, proving reliable for a huge range of requirements and uses. When ready to use ensure surfaces to be joined are clean, completely dry, and close-fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$9.95
LOCTITE® SI 598™ cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. This product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers. This product is typically used in applications with an operating range of -54 °C to 260 °C. Metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. LOCTITE® SI 598 is a metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. It cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. It resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. This product is typically used in applications with an operating range of -54 to +260°C. Excellent resistance to automotive motor oils Enhances load bearing & shock absorbing characteristics of the bond area Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers Technical Information Color Black Fixture Time 30 Fixture Time Temperature 30 °C Physical Form Paste Technology Silicone TYPICAL ENVIRONMENTAL RESISTANCE The product retains effective properties in contact with automotive fluids, such as motor oil, transmission fluids, alcohol and antifreeze solutions. NOTE: Not recommended for parts in contact with gasoline. Directions for use: 1. For best performance bond surfaces should be clean and free from grease. 2. Full performance properties will develop over 72 hours. 3. Moisture curing begins immediately after the product is exposed to the atmosphere, therefore parts to be assembled should be mated within a few minutes after the product is dispensed. 4. Excess material can be easily wiped away with non-polar solvents. NOTE: LOCTITE® SI 598™ is not recommended for use as a cylinder head gasket or head gasket sealant. 5. For full automatic applications a volumetric dispensing system is recommended.
$15.52
Adhesive permanently remounts mirrors to windshields LOCTITE® Rearview Mirror Adhesive is approved and used by GM, Ford and Daimler-Chrysler. Permanently remounts mirrors to windshields. Achieves handling strength in seconds; mirror-mounting strength in 15 minutes. Mounting rearview mirrors to windshields.
$25.00
LOCTITE® 249 is a blue, dimethacrylate ester acrylic film thread locker. It is supplied in a low tack film to provide a convenient and easy to use package, especially where a liquid product may be too fluid to stay on a part or be difficult to apply. This product can be used for immediate assembly or days later and provide consistent strength on a variety of metal substrates. Dimethacrylate ester acrylic film threadlocker. It is supplied in a low tack film to provide a convenient and easy to use package. Designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand tools Supplied in a low tack film to provide a convenient and easy to use package Can be used for immediate assembly or days later Provides consistent strength on a variety of metal substrates Technical Information Color Blue Cure Type Activator Cure, Anaerobic Cure Full Cure Temperature 77 °F Key Characteristics No Mix Number of Components 1 Part Physical Form Film Storage Temperature 46 - 69 °F Technology Acrylic Temperature -65 - 300 °F Thread Size (Maximum) R3/4" Torque Break on M10 Steel 74 in./lb. Torque Prevail on M10 Steel 47 in./lb. Viscosity 8700 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$16.08
Loctite Go2 Gel contains a revolutionary FLEXTEC® formulation that bonds multi-materials when projects or repairs require higher viscosity, tremendous bond strength, and resistance to extreme conditions. It is a versatile, gap-filling adhesive that bonds, seals and repairs almost all materials. It is ideal for bonds subject to harsh or extreme conditions or for situations where constant flexing is a problem. It can be used indoors and outdoors, has excellent adhesion and high initial grab that cures quickly. Loctite Go2 Gel dries clear and creates a flexible and durable bond which is dishwasher safe and has excellent resistance to vibration, impact, moisture, UV and extreme temperatures, offering long reliability anywhere it is used. Recommended For NOTE: 1See limitations below in the 'not recommended for' section. Compatible with many porous and non-porous materials such as metals1 (aluminum, stainless steel, steel, copper, brass, bronze, zinc, etc.), glass, concrete, ceramic, tiles, natural stones, wood, cork, paper, cardboard, textiles, leather, varnished surfaces1, chipboard, MDF, fiberglass reinforced polyester, rigid PVC, polycarbonate, sanded ABS, and polystyrene foam/Styrofoam™. DIY repairs and modelling work in and around the house. Not Recommended For Before application, carry out tests to ensure the compatibility with non-ferrous metals such as aluminium, copper, bronze and brass as well as with different coatings such as paints, varnishes and powder coatings. Variations in the composition may affect adhesion. Aquariums or potable water systems Archival applications Applications requiring service temperatures below -58°F (-50°C) and above 248°F (120°C) Polyethylene (PE), polypropylene (PP) and polytetrafluoroethylene (PTFE) plastics, metal-to-metal (one surface should be porous) or rubber Applications requiring solvent resistance Applications with prolonged water immersion Safety Precautions Well-ventilated area, gloves. Preparation Use between 41°F (5°C) and 104°F (40°C). Protect work area. Surfaces must be clean and free of grease, dust and other contaminants. For improved adhesion, abrade very smooth surfaces (such as metal) prior to cleaning. Remove cap. Application Apply a thin layer of adhesive to one surface. Immediately position and press parts firmly together within 5 minutes. For difficult bonds, clamp parts or use tape to hold pieces together. Do not move or use parts for at least 2 hours. Full bond strength is achieved in 24 hours. Cure times will increase with lower temperatures and humidity and if bonding two non-porous surfaces. For Gap-Filling: Apply in a thick layer to fill gaps up to 5mm max. Fix or clamp the items together for 1-3 hours and do not touch or move them. In 24 hours, 70% of full adhesion and bond strength is achieved. Cure time is 24 hours for every 2mm of adhesive. To Get High Initial Grip: Apply on both surfaces in thin and even layers. Leave for 3-5 minutes. Use as a contact cement. After, GO2 gel has become tacky, bring the items together immediately and press firmly. Fixation is not necessary in many cases. Note that final strengths decrease when used as a contact glue. Two Non-Porous Surfaces: Bonding two non-porous surfaces can result in a slower cure time and is generally not recommended. If bonding two non-porous surfaces, surfaces can be wetted using a damp cloth, taking care to avoid wetness, pooling water or drop formation, to optimize cure time. Cleanup Clean tools and adhesive residue immediately with mineral spirits. Cured adhesive may be carefully cut away using a sharp-edged tool.
$11.70
Part N° 546018 (MA3) LOCTITE AUTOMOTIVE REARVIEW MIRROR ADHESIVE • Special Loctite bonding system for attaching metal rear-view mirror buttons to windscreens. Ideal for larger mounting brackets • Absorbs difference in thermal expansion - also recommended for metal locks and hinges on side windows and glass to metal applications on furniture. Contents: 1 piece of nylon mesh 40mm x 40mm - Diagram 1 Part B. 1 tube of Loctite adhesive - Diagram 1 Part A. Contents are sufficient for one rear-view mirror application. Note: the adhesive must be used with the special nylon mesh Directions for use: - Where convenient, remove the metal bracket from the mirror bracket. Do not damage the metal bracket Place the car in shade for at least one hour before commencing the repair. The ideal temperature for this 2 repair is between 15°C and 25°C Diagram 3: Mark an outline of the bracket on the outside of the windscreen with a marking pen Ensure the position of the bracket will result in the mirror hanging in the correct way. - Remove all old adhesive from the bracket with fine sandpaper, and from the screen with a sharp blade or razor blade. Wipe clean the inside of the screen with an ammonia-based detergent or LOCTITE SF 3 7850 Orange hand cleaner, then wipe again with a clean cloth dampened in Methylated Spirit. Allow drying. Cut the nylon mesh to the exact shape of the metal bracket that will fit onto the windscreen. Hands must be clean and oil-free while doing this. - Cut the tip from the adhesive tube (Dia. 1, Part A), apply the adhesive from the tube and spread over the entire area of the metal bracket - Place the cut to size nylon mesh onto the adhesive on the metal bracket. Important. The adhesive will begin curing within 30 seconds of contact with the nylon mesh. Diagram 7: Note Ensure the bracket is in the correct position (top and bottom front and back) With the nylon mesh and adhesive assembled, press the bracket and mesh against the inside of the windscreen aligned with the marked location and hold firm for a minimum of 30 seconds Wipe off any excess adhesive, Allow adhesive to cure for at least 15 minutes before mounting the mirror to the bracket. Warning: Adhesive may attack some painted surfaces.
$19.95
LOCTITE 660 is a high strength retaining compound with good gap filling properties, ideal for repairing worn-out seats, keys, splines, bearings or tapers without remachining. LOCTITE® 660 is designed for the bonding of cylindrical fitting parts, particularly where bond gaps occurs without the need for remachining. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. LOCTITE 660 exhibits excellent gap cure characteristics and is also suitable for retaining shims. Ideal for repairing worn parts without remachining Enables re-use of worn bearing seats, keys, splines or tapers Suitable for retaining shims P1 NSF Reg. No.: 123704 Technical Information Agency Approvals / Specifications NSF P1 Color Silver Diametrical Clearance (Maximum) Unit mm Fixture Time 15 min. Fixture Time Temperature 15 °C Gap Fill 0.5 mm Key Characteristics Thixotropic Substrates Metal: Steel
$10.59
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
High strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. LOCTITE® 609 is a green, high strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. The product cures in the absence of air between close-fitting metal surfaces. Typical applications include rotor to shafts in fractional and subfractional horsepower motors. Locks bushings and sleeves in housings on shafts. Augments press fits. Low viscosity Prevents loosening and leakage from shock and vibration Augments press fits Tested to the lot requirements of Military Specification Mil-R-46082B (this is a regional approval) Technical Information Agency Approvals / Specifications ASTM D5363, CFIA Listed, MIL-R-46082B for existing designs Application Method Pressure Applications For Close Fitting Parts, Retaining Colour Green Cure Type Anaerobic Cure Diametrical Clearance (Maximum) Unit in. Fixture Time 10 min. Fixture Time Temperature 10 °C Full Cure Temperature 22 °C Full Cure Time 24 hr. Gap Fill 0.006 in. Key Characteristics Fluorescent, Strength: High Strength, Viscosity: Low Viscosity Number of Components 1 Part Physical Form Liquid Shear Strength Unit, Steel psi Shear Strength, Steel 2300 Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal Technology Acrylic Temperature -65 - 300 °F Viscosity 125 mPa.s (cP) Brookfield Viscosity (#7sp/20/rpm) 125 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$12.12
Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing. LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part. Ideal for fine threads as used in hydraulic, pneumatic & general fittings Suitable for metal threads only Instant low-pressure seal Resistant to fuel, oil, coolants and hydraulic fluids Locks connection against vibration loosening PRODUCT DESCRIPTION LOCTITE® 542 provides the following product characteristics: Technology Acrylic Chemical Type Dimethacrylate ester Appearance (uncured) Brown liquidLMS Components One component - requires no mixing Viscosity Low Cure Anaerobic Secondary Cure Activator Application Thread sealing Strength Medium Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry. 3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also. 4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations. 5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours. For Disassembly 1. Remove with standard hand tools. 2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot. For Cleanup 1. Cured product can be removed with a combination of soaking in a Loctite solvent and mechanical abrasion such as a wire brush.
$12.26
Black, toughened ethyl-based instant adhesive. Well suited to plastics, rubbers, metals as well as porous/acidic surfaces. LOCTITE® 438 is a black, toughened ethyl-based instant adhesive. It has a fixture time of 10 - 20 secs., high impact resistance and is flexible. It is suitable for bonding plastics, rubber, metals, porous and absorbent substrates and acidic surfaces. Good resistance in humid environments. Cures very quickly when confined between two surfaces Ideal for bonding small to medium-size parts Excellent adhesion to most substrates Suitable for rubbers and plastics Well suited to metals, porous and/or acidic surfaces Fixture time of 10 - 20 secs. Solvent-free Toughened, black
$35.00
LOCTITE 290 is a medium/high strength, wicking grade threadlocking adhesive that is ideal for locking preassembled fasteners. LOCTITE® 290 is a liquid medium/high-strength threadlocker designed for the locking and sealing of threaded fasteners. Because of its low viscosity and capillary action, the product wicks between engaged threads and eliminates the need for disassembly prior to application. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The product can also fill porosities in welds, castings and powdered metal parts. Ideal for locking preassembled fasteners, e.g. instrumentation fasteners, electrical connectors and set screws Works on metal only Proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Requires heat for disassembly
$12.48
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$19.23
Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
You have seen 96 out of 111 products
Formulations that maintain bond integrity under vibration and shock, ideal for vehicles, machinery and equipment. Consider threadlockers for fasteners and toughened systems for bonded joints. Use filters to refine by chemistry and temperature rating. Always review the product page and TDS/SDS.
