Hold It Australia T72 STUDLOCK High Temp High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T72 Studlock is a High Strength-High Temperature Threadlocker. This red, single component, anaerobic adhesive is ideal for joining threaded parts exposed to operating temperatures up to 232°C. Its enhanced chemistry allows superior performance at temperatures significantly higher than other thread locking products. Applications T72 is perfect for high-temperature locking and sealing of studs, nuts, screws, bolts, and fittings. It effectively locks and seals parts against leakage, contamination, and corrosion, particularly suitable for larger diameter, coarse-threaded parts. Recommended for components not requiring routine maintenance, as disassembly can be challenging and may require heat. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T71 THREADLOCK High Strength, Low Viscosity - 50ml Description: HOLDIT AUSTRALIA T71 Threadlock is a high-strength, anaerobic thread locking compound. T71 is developed for the permanent locking of threaded fasteners and performs well on aluminium, steel, plated fasteners, stainless steel, and special alloy parts. It boasts good temperature stability and solvent resistance. Applications T71 is designed to lock and seal large fasteners, especially in applications where shock and vibration might cause loosening. Its high strength ensures a reliable lock in demanding environments. Instructions for Use Clean all surfaces with a cleaning solvent and let them dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or to the internal threads of a blind hole. Assemble the components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia STUDLOCK Mid Strength Lubricated for Torque Assembly - 50ml Description: HOLDIT AUSTRALIA T62 Lubricated Thread Locker is a medium strength, anaerobic thread locking compound, perfect for permanent locking of threaded fasteners. T62 is effective on aluminium, steel, plated, stainless steel, and special alloy parts. It is characterized by its good temperature and solvent resistance. Applications Designed for locking and sealing large fasteners (1 and larger), T62 is ideal for applications where shock and vibration may cause fasteners to loosen, ensuring a stable and permanent lock. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal adhesion. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying any load. Active & Inactive Metal Table Consult the Active and Inactive Metal Table for specific application guidance on different metal types.
$34.86
Hold It Australia T43 NUTLOCK Medium Strength (Oil Tolerant) - 50ml Description: HOLDIT AUSTRALIA T43 Nutlock is an oil tolerant, medium viscosity, Thixotropic, anaerobic thread locking adhesive suitable for all types of metal threaded fasteners. The cured adhesive offers controlled medium strength, excellent temperature, and solvent resistance, particularly against water and nonpolar solvents. It rapidly cures on plated, oily metal surfaces or inactive surfaces. Applications Ideal for replacing lock washers and plastic inserts, NUTLOCK locks machine tool access bolts, studs, hydraulic system bolts, gear box bolts/drive shaft, bearing cover cap screws, counter sunk screws, conveyor roller bolts, and is suitable for construction equipment. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal bonding. If metal is inactive or cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Please consult the Active and Inactive Metal Table for specific application guidance.
$34.86
Hold It Australia T22 SCREWLOCK Low Strength for Easy Disassembly - 50ml Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance. Applications T22 is specifically formulated to lock and seal small screws (less than ¼), including set screws with long engagement lengths. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal results. If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow to fully cure before applying load. Properties of Uncured Material Chemical Type: Anaerobic Colour: Purple Toxicity: Low Solid Content: 100% Viscosity @ 25°C, cPs: 900-1,500 cps Specific Gravity: 1.05 Shelf Life: 24 months Performance of Cured Material Fixture Speed: 15-20 Min @ 22°C Full Cure: 24 Hours @ 22°C Temperature Range: -50°C to 150°C Product Conformity: MIL-S-46163A, ASTM D-5363, NSF Technical Datasheet The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm 9Nm on 3/8 plain steel nut & bolt after 1 hour and 5Nm 11Nm after 24 hours. On a 3/8 zinc nut & bolt, the strength is 1Nm 4Nm after 24 hours. Environmental and Fluid Resistance Heat Age: 100% retention in Engine oil @ 150°C Brake Fluid @ 150°C: 85% retention ATF @ 150°C: 85% retention 50/50 water/ethylene glycol @ 120°C: 80% retention Water @ 100°C: 80% retention Gasoline @ 25°C: 95% retention Diesel Fuel @ 25°C: 100% retention Ethyl Alcohol @ 25°C: 90% retention Active & Inactive Metal Table Category Cure Speed Metals Super Active Very Fast Cure Brass, Copper, Magnesium Active Fast Cure Iron, Steel, Nickel, Aluminium Inactive Slow Cure Stainless Steel, Titanium, Zinc Passive Primer Necessary Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes
$34.86
GorillaWeld is an incredibly strong, heavy duty two-part adhesive. The tough, steel bond epoxy formula has a 4250 PSI bond strength and sets in just 10 minutes. GorillaWeld is waterproof and versatile, creating a long-lasting, permanent bond to metal, plastics*, concrete, ceramics, PVC, fibreglass and more! Features: INCREDIBLY STRONG: 4250 PSI STEEL BOND EPOXY SETS IN 10 MINUTES WATERPROOF** FORMS PERMANENT BOND DRIES DARK GRAY EASY TO USE BONDS: Metal, Plastic*, Concrete, PVC, Fiberglass, Ceramic & More! *Not recommended for use on polyethylene or polypropylene plastics. **Bonded wood materials should not be submerged or soaked in water. Directions All surfaces should be clean and free of debris. To improve adhesion, roughen smooth surfaces with sandpaper before gluing. Remove cap from each tube and use top of cap to puncture foil seal. Dispense equal parts from each tube onto a clean, disposable surface. Mix with disposable mixing tool for approximately 20 seconds until the colour is uniform. Apply mixture to surface within 3 minutes. Clamp surfaces together and leave undisturbed for 10 to 30 minutes. Full cure in 24 hours. Cure time dependent on temperature, humidity and quantity applied. *Note: Not recommended for use on polyethylene, polypropylene or similar plastics. Specs: APPLICATION TEMPERATURE: 32°F to 90°F SERVICE TEMPERATURE: -40°F to 300°F SET TIME: 10 minutes CURE MECHANISM: 2 Part Reaction, requires mixing OUTDOOR: Yes FREEZE/THAW STABLE: Yes WATERPROOF: Yes* PAINTABLE: Yes SANDABLE: Yes DRILLABLE: Yes SHAPEABLE: Yes STAINABLE: No CHEMICAL RESISTANT: Limited EXPANDS WHEN CURED: No SHRINKS WHEN CURED: No CURED COLOR: Dark grey GAP FILLING: Yes *Not suggested to use on wood materials submerged or soaked in water Will GorillaWeld bond plastic/vinyl/rubber? Gorilla Weld will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP), polyethylene (PE) or similar plastics, or any type of rubber with high oil or plasticizer content. What does GorillaWeld work best for? GorillaWeld is ideal for metal and plastic (see above) substrates. GorillaWeld does not sag so it is ideal for vertical surfaces How should GorillaWeld be stored? GorillaWeld should be stored in a cool, dry place. Store away from children and animals. How do I mix GorillaWeld? GorillaWeld should be mixed 1:1 for 20 seconds or until uniform prior to application. Does GorillaWeld become hot during cure? Yes, mixing the hardener and resin together creates an exothermic reaction and will generate heat during cure. Consideration should be taken on mixing vessel as not to melt. How long do I have before GorillaWeld begins to harden? GorillaWeld will begin to harden after 3 minutes. Adhesive should be applied prior. What surfaces will GorillaWeld bond to? GorillaWeld is particularly suited for metal, plastic and other rigid surface bonding. Is GorillaWeld Food Safe? GorillaWeld is not recommended for direct or indirect food contact and should not be considered food safe. Why is GorillaWeld odour so strong? GorillaWeld is based on methyl methacrylate chemistry which has a naturally strong odour. We suggest using in a well-ventilated area. How do I remove GorillaWeld from body/skin? Uncured: GorillaWeld can be harmful through skin absorption and it is strongly recommended that you wear gloves during use. If GorillaWeld is on the skin, try removing with a dry cloth or paper towel and then wash the area thoroughly with soap and water. Cured: Cured material can be rolled off the skin. Remove as much cured material as possible and wash the area thoroughly with soap and water. For medical emergencies, call 1-800-420-7186 anytime How do I remove GorillaWeld from my surface? Uncured: Wipe up as much material as possible with a dry cloth and clean any remaining product/residue with Isopropyl alcohol (IPA) or acetone following solvent manufacturer’s instructions. Cured: For removing cured/dried GorillaWeld, mechanical means such as sanding or chiselling. What should I do if I think a human or animal has ingested GorillaWeld? For medical emergencies, call 1-800-420-7186 anytime
$15.82
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. PRODUCT FEATURES CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More APPLICATION TEMPERATURE – 0°C to 37.8° C, best at room temperature SERVICE TEMPERATURE – -28.9° to 82.2° C OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – Minimal What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight fitting joints. It’s perfect for a fix you need done fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also minimally gap filling, which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant, and can withstand intermittent exposures, however is not meant for a constant soak. Original Gorilla Glue is 100% waterproof and can withstand soaking and longer term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$14.92
Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles. Surface Preparation: Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded. Mixing: Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing. Application: Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates. Coverage: Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel. Drying Time: Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools. Clean-up: Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically. Technical Data: Classification: C2S1TE Pot life: 1.5 hours Open time: 30 minutes Adjustability time: 20 minutes VOC content: Low Appearance: White powder
$30.14
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$28.96
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$16.00
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$11.05
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.00
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams. Very high strength Watertight bonds Above/Below waterline use Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour
$55.00
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams. Very high strength Watertight bonds Above/Below waterline use Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour
$55.00
You have seen 111 out of 111 products
Formulations that maintain bond integrity under vibration and shock, ideal for vehicles, machinery and equipment. Consider threadlockers for fasteners and toughened systems for bonded joints. Use filters to refine by chemistry and temperature rating. Always review the product page and TDS/SDS.
