In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects.
Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes
Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color
Full Cure: 24 Hours
Application
For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.
Clamping
The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.
Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.
Cure Time (amount of time for glue to reach total bonding strength): 24 hours
Clean Up
Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse.
Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.
Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.
To remove Gorilla Wood Glue from hands, wash with warm soap and water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects.
Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes
Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color
Full Cure: 24 Hours
Application
For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.
Clamping
The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.
Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.
Cure Time (amount of time for glue to reach total bonding strength): 24 hours
Clean Up
Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse.
Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.
Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.
To remove Gorilla Wood Glue from hands, wash with warm soap and water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Seal leaks fast and protect exposed joins with Grunt Flashing Tape. This heavy duty self adhesive tape conforms to uneven surfaces, creates a long lasting waterproof barrier, and is ideal for quick fixes and preventative maintenance across roofs, gutters, and outdoor fixtures.
Why choose this tape
Weatherproof seal that helps stop water ingress at laps, seams, and penetrations.
Strong tack for reliable adhesion on metal, plastic, and painted surfaces.
Flexible backing that moulds to contours, ridges, and fasteners.
UV and outdoor ready for Australian conditions.
Clean finish suitable for temporary and permanent repairs.
Common uses
Sealing gutter joins, end caps, and mitres
Flashing around skylights, flues, and vents
Stopping drips at roof sheet overlaps
Repairing small cracks in downpipes and rainwater fittings
Protecting fasteners and exposed fixings from water
General waterproofing on caravans, sheds, pergolas, and trailers
Surface compatibility
Works on most clean, dry, and sound substrates including coated metal roofing, painted timber, rigid plastics, fibreglass, and masonry that has been sealed. Not recommended for silicone contaminated surfaces or areas that remain permanently submerged.
How to apply
Prepare the area. Remove dust, old flaking coatings, oil, and loose rust. Dry the surface thoroughly.
Measure and cut the tape to length with a knife or scissors.
Peel and stick. Remove the release liner as you apply, pressing the tape down firmly.
Roll with a hand roller or the back of a cloth to eliminate air pockets and ensure full contact.
Overlap adjoining pieces by at least 25 mm for a continuous seal.
Finish edges with extra pressure. Avoid applying in rain or onto wet surfaces.
Pro tips
For porous substrates, prime with a suitable primer and allow to dry before taping.
Cold weather can reduce tack. Warm the tape and surface slightly to improve bond.
Ensure water can shed over the tape rather than against the lap direction.
Specifications
Brand
Grunt
Product type
Self adhesive flashing and sealing tape
Size
50 mm width x 10 m length
Use
Exterior and interior repairs, roofs, gutters, and general waterproofing
Application temperature
Apply in dry conditions on clean and sound surfaces
Cleanup
Wipe tools with mineral turpentine or adhesive remover as suitable for the substrate
Frequently asked questions
Can I paint over itYes, most solvent based and acrylic paints will adhere. Test a small area first.
Is it suitable for potable waterNot intended for potable water contact.
Will it work on damp surfacesBest results are achieved on dry surfaces. Dry the area before application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gyprock CSR Acrylic Stud Adhesive 1 kg is a reliable acrylic stud adhesive for secure plasterboard fixing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 1 kg pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Gyprock CSR CSR for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Gyprock CSR Acrylic Stud Adhesive 1 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Fixing plasterboard to studs and battens
Reducing the chance of nail pops and drumminess
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Timber framing and battens
Metal studs as directed by code
Back of plasterboard
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of install sheets within the wet time window. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Apply daubs as specified, then fix sheets with screws or nails. Adhesive cures to a resilient bond that complements mechanical fastening.
Temperature and environmental performance
Use in moderate temperatures for consistent cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean fresh residue with a damp cloth. Scrape away cured beads before setting coats. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Keep sealed. Do not allow to skin in the tub. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Achieve smooth, long lasting plasterboard joints with Gyprock CSR FibaFuse Joint Tape. This premium paperless tape bonds beautifully with both setting and drying compounds to reinforce seams, reduce the risk of cracks, and deliver a professional finish on walls and ceilings.
Why choose FibaFuse
Stronger joints thanks to an open fiber structure that integrates with joint compound for excellent reinforcement.
Smooth finishing with feathered edges that sand and paint cleanly.
No bubbling when properly embedded in compound for a flat, reliable seam.
Works with most compounds including setting type and ready mixed formulas.
Ideal for pros and DIY on new installs, repairs, and patchwork.
Best for
Joining plasterboard sheets on walls and ceilings
Butt and tapered edge joints
Repairs to cracked or previously patched seams
High traffic areas that need extra durability
How to use
Prep Ensure surfaces are clean, dry, and free of dust. Lightly bevel cut edges if required.
Bed coat Apply an even layer of joint compound over the seam at least the width of the tape.
Embed Place the FibaFuse tape into the wet compound and press firmly with a taping knife to remove air pockets.
Cover Apply a thin coat over the tape to fully conceal the mesh. Allow to dry or set as per the compound directions.
Build Apply one or two wider coats, feathering the edges for a flat transition. Let each coat dry before the next.
Finish Lightly sand, prime, and paint.
Pro tips
Keep knife pressure firm during embedding to avoid bubbles.
Use a wider knife for second and third coats to reduce sanding.
Prime before painting for a consistent sheen across joints and boards.
Product details
Brand
Gyprock CSR
Type
Paperless joint tape for plasterboard seams
Compatibility
Setting and ready mixed joint compounds
Applications
Walls, ceilings, butt joints, tapered edges, repairs
Frequently asked questions
Do I need to pre soak the tapeNo. Embed the tape directly into wet compound.
Can I use it with ready mixed compoundYes. It works with ready mixed and with setting type compounds. Follow the compound instructions for drying or set times.
Will it show through paintNot when properly covered with compound, sanded smooth, and primed before painting.
Good to know
Store flat and dry to maintain tape integrity.
Always wear appropriate PPE when sanding joint compound.
Glues Australia helps you get a strong, professional finish without the fuss. Why buy new when you can fix
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Get pro level finishes without the fuss. Gyprock CSR Less Mess Joint Compound is a pre mixed, easy sanding compound that helps you achieve smooth, paint ready walls with less splatter and minimal clean up. The handy 2.25kg tub is perfect for repairs, patching, jointing, and touch ups around the home or on site.
Why you will love it
Pre mixed convenience that is ready to use straight from the tub
Less mess formula that helps reduce splatter and clean up time
Easy to apply, easy to feather, and easy to sand smooth
Low shrinkage for fewer repeat passes
Paintable finish that accepts most interior paints
Great for joints, screw head covering, corner repairs, and small patches
Best suited for
Interior plasterboard joints and repairs
Skim coating small areas to blend texture
Covering fasteners and minor cracks
DIY touch ups and trade maintenance work
How to use
Surface prep: Ensure the area is clean, dry, dust free, and sound. Remove loose material and lightly scuff glossy paint.
Application: Stir gently. Apply with a broad knife or trowel in thin, even coats. Feather edges well.
Drying: Allow each coat to dry fully before recoating. Dry time varies with film thickness, temperature, and humidity.
Sanding: Sand lightly with fine paper for a smooth finish. Remove dust before painting.
Paint: Seal with a suitable primer then finish with your chosen interior paint.
Tips for a flawless finish
Work in thin passes rather than one heavy fill
Keep your knife clean and slightly flexible for smooth feathering
Use a dry sanding block or pole sander and avoid over sanding
For deeper holes, build up in multiple coats
Frequently asked questions
Is it sandable and paintable? Yes. Once fully dry, sand lightly and prime before painting.
Can I use it on previously painted walls? Yes, provided the paint is sound, clean, and lightly keyed.
Is it suitable for wet areas? Use in dry interior spaces. For wet areas, follow local building guidelines and use appropriate systems.
Specifications
Brand
Gyprock CSR
Product
Less Mess Joint Compound
Pack size
2.25kg tub
Colour
Off white
Use
Interior plasterboard jointing and patching
Cleanup
Water while wet
Finish
Sandable and paintable
Storage
Reseal tightly. Store cool and dry. Do not allow to freeze.
Good to know
Coverage varies with joint size, substrate, and application method
Dry times depend on thickness, temperature, and humidity
Always test on a small area when working over sensitive or unknown coatings
Safety
Use in a well ventilated area
Avoid breathing sanding dust. Wear a suitable mask and eye protection
Keep out of reach of children
Why buy from Glues Australia
Fast dispatch Australia wide
Careful packaging to protect your order
Local support when you need advice
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The HandyPal GripWrap 100mm x 250m Mini Shrink Wrap is your go-to solution for all packaging needs, offering unmatched durability and ease of use. Made from high-quality, tear-resistant material, this shrink wrap is designed to withstand the toughest handling during moving, shipping, or storage. The compact and ergonomic design ensures a comfortable grip, making it ideal for wrapping both small and irregular-shaped items with precision. The clear, transparent film allows for easy identification of contents without the need to remove the wrap, saving time and ensuring efficiency.
Perfect for bundling items, securing packages, and protecting goods from dust and moisture, the HandyPal GripWrap offers versatile applications in both personal and professional settings. With an impressive 250m length, this wrap is built for long-term use, making it the perfect choice for large projects or ongoing packaging needs. Whether you're a DIY enthusiast or a professional, the HandyPal GripWrap provides reliable, high-quality protection you can count on.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A water-based timber and grain filler, suitable for both interior and exterior use. Woodblend sands to an extremely fine, smooth finish. Woodblend can be coated with water or oil-based timber finishes and paints. Available in six inter-mixable colours.
KEY PRODUCT INFORMATIONCoverage: 5m2/LRecoat: 2hrsFull cure: N/AClean up: WaterSheen: N/A
USAGE INSTRUCTIONS
WHERE TO USEAreas: All interior timber, Exterior timberSubstrates: All interior timberLocations: Interior, Exterior
APPLICATIONMethods: Filling blade or knife
1. Apply WoodBlend with a flexible filling blade or knife. Fill deep holes in approx. 10mm stages, allowing two hours drying time between each stage.2. To ease application, dampen blade with water.3. Wipe off excess with a slightly damp sponge. When dry, sand to a smooth finish.4. When using clear finishes, apply WoodBlend after the first coat of clear to minimise smudging.5. For use as a grain filler, thin WoodBlend with 5-10% water to achieve the required consistency. Apply with a flexible filling blade or knife and allow to dry. When dry, sand back to bare timber, leaving filler only in the grain.
IMPORTANT: Keep container tightly closed when not in use.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey color. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured.
Great For:
Household Repairs
Automotive
Plumbing
Marine
Crafts & More
STRENGTH: 3960 PSI
SET TIME: 4-6 Hours
CURE TIME: 15-24 Hours
CURE COLOR: Dark Grey
Use On:
Automotive
Brick
Concrete
Epoxy & Adhesives
Fiberglass
J-B Weld
Metal
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
ExtremeHeat™ is formulated to allow for repairs to iron, steel and metal in high temperature environments (2400°F / 1300°C). When fully cured, this metallic compound can be drilled, machined or sanded. It is great for repairing cracks, small gaps, seam connections or holes in exhaust manifolds, pipe connections, mufflers, catalytic converters, outdoor grills, fire boxes, gas and commercial furnaces and water heaters. This product is water based, non-flammable and contains no solvents or Volatile Organic Compounds (VOCs).
GREAT FOR
Exhaust Manifolds
Tail Pipes
Mufflers
Engine Blocks
Duct Work
Heat Exchange Units
Fire Box / Fire Place
Outdoor Grills
USE ON
Automotive
Metal
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
HighHeat™ is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat™ is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat exposure of 400ºF and intermittent heat exposure to 550ºF
GREAT FOR
Exhaust Manifolds
Tail Pipes
Mufflers
Engine Blocks
Duct Work
Machinery
High Temperature Projects
USE ON
Automotive
Metal
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
KwikWeld™ is a fast-setting version of The Original J-B Weld two-part epoxy cold weld system that provides strong, lasting repairs to metal and multiple other surface types. After mixing, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. KwikWeld™ has a 1:1 mixing ratio, sets in 6 minutes and is fully cured in 4-6 hours. KwikWeld™ cures to a dark grey color, is rated at a tensile strength of 2424 PSI and will withstand temperatures up to 300ºF.
GREAT FOR
Household Repairs
Automotive
Plumbing
Marine
Crafts & More
USE ON
Automotive
Brick
Ceramic
Concrete
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
MarineWeld™ is a specially formulated two-part epoxy cold weld system that provides for strong, lasting repairs for bonding different or similar surfaces, such as aluminium, metal, composites, fibreglass and others. MarineWeld™ sets in 4-6 hours at room temperature and is fully cured to a dark grey colour in 15-24 hours. Once cured, it can be shaped, tapped, filed, sanded and drilled and will retain its strength above or below the waters' surface. MarineWeld™ has a 1:1 mixing ratio and tensile strength of 5020 PSI.
GREAT FOR
Boats
Personal Watercraft
In/Outboard Engines
Deck & Hull Accessories
USE ON
Fibreglass
Under Water/Wet
And More
STRENGTH 5020 PSI
SET TIME 4-6 Hours
CURE TIME 15-24 Hours
CURE COLOR Dark Gray
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Plastic Bonder is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. Plastic Bonder has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, Plastic Bonder sets to a tan colour and cures to a hard, permanent bond.
GREAT FOR
Filling Dents
Bumpers
Automotive Trim
Composite Panels
Interior & Exterior Plastic Parts
Fibreglass
USE ON
Automotive
Brick
Ceramic
Concrete
Epoxy & Adhesives
Fibreglass
Plastic/Composite/PVC
Wood
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
PlasticBonder™ is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. PlasticBonder™ has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder™ sets to a tan colour and cures to a hard, permanent bond.
GREAT FOR
Filling Dents
Bumpers
Automotive Trim
Composite Panels
Interior & Exterior Plastic Parts
Fibreglass
USE ON
Automotive
Brick
Ceramic
Concrete
Fibreglass
Plastic/Composite/PVC
Wood
And More
PREPARE
Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair.
MIX
After removing the replaceable cap, press down on the plunger and squeeze equal amounts onto a disposable surface and mix thoroughly.
APPLY
Apply with appropriate tool in an even coat, weld bead or extruded shape as needed.
DRY
Sets in 15 minutes. Cures in 30 minutes. If the temperature is below 40ºF, then set time is longer.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
PlasticWeld is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. *After mixing, it forms a polymer compound that can be moulded or used to build up and repair just about anything made from plastic. When cured, it can be sawed, drilled, carved, sanded and painted. PlasticWeld has a 20-25 minute work life; functional cure occurs in 2-3 hours. PlasticWeld cures to an off-white colour, is rated at a tensile strength of 350 PSI. Does not adhere to polyethylene, polypropylene or some other plastics. Test for adhesion first.
GREAT FOR
Rigid & Semi-flexible Plastic
ABS, PVC & CPVC Pipes
Automotive Trim & Bumpers
Fibreglass Parts
Vinyl Siding
STRENGTH: 350 PSI
SET TIME: 25 Minutes
CURE TIME: 3 Hours
CURE COLOR: Off White
Drinking Water Safe
USE ON
Automotive
Ceramic
Epoxy Putty Sticks
Fiberglass
Plastic/Composite/PVC
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
PlasticWeld is a specially formulated two-part adhesive and epoxy filler system that provides for strong, lasting repairs. PlasticWeld will bond a variety of surfaces, such as metal, composites, fiberglass and others. PlasticWeld sets in 5 minutes at room temperature and is fully cured in 1 hour. Using a 1:1 mixing ratio, PlasticWeld combines to a tensile strength of 3200 PSI and cures to an off-white color.
GREAT FOR
Most Hard Plastics
ABS
Fibreglass
PVC
Glass
Vinyl
STRENGTH 3200 PSI
SET TIME 5 Minutes
CURE TIME 1 Hour
CURE COLOR Off White
USE ON
Automotive
Ceramic
Epoxy & Adhesives
Fibreglass
Plastic/Composite/PVC
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey colour. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured.
Great For:
Household Repairs
Automotive
Plumbing
Marine
Crafts & More
Strenght: 3960 PSI
Set Time: 4-6 Hours
Cure Time: 15-24 Hours
Cure Colour: Dark Grey
Use on:
Automotive
Brick
Concrete
Epoxy & Adhesives
J-B Weld
Metal
Pro Sizes
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
SteelStik is a hand-mixable, steel-reinforced, non-rusting epoxy putty that quickly repairs or rebuilds anything made of metal. After mixing, it forms an industrial-strength polymer compound that can be moulded into shapes or used to build up patch and repair steel components. SteelStik sets in 3-5 minutes and after 60 minutes, can be drilled, tapped, machined, ground, filed and painted. SteelStik cures to a dark grey colour is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF.
GREAT FOR
Automotive & Machine Parts
Exhaust Systems
Plumbing
Stripped Threads
Rust Damage
Household Repairs
STRENGTH 900 PSI
SET TIME 5 Minutes
CURE TIME 1 Hour
CURE COLOR Dark Grey
USE ON
Automotive
Brick
Ceramic
Concrete
Epoxy Putty Sticks
Metal
Under Water/Wet
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
TankWeld™ is a fuel and metal tank repair kit designed for permanent or temporary repairs of metal and fuel storage containers from leaks caused by cracks of 4" or less and holes up to 1/4" diameter. This kit is not recommended for plastic repairs of for use with polyethylene or polypropylene plastic parts.
GREAT FOR
Metal Gas Tanks
Metal Tanks & Oil Pans
USE ON
Metal
And More
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
WaterWeld will plug or seal leaks and patch holes and cracks in almost anything. Ideal for repairing plumbing, fuel tanks, tub and shower, drains, pool and spa, boats and potable water tanks; setup occurs even under water. After curing, it can be drilled, tapped, filed, sanded and painted. WaterWeld has a set time of 15-25 minutes and sets hard in one hour. WaterWeld cures to an off-white color, is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF.
Great For:
-Plumbing, Tub, Shower & Drains
-Fuel Tanks
-Marine & Boats
-Potable Water Tanks
Strenght: H900 PSI
Set Time: 25 Minutes
Cure Time: 1 Hour
Cure Colours: Off White
Use On:
-Automotive
-Ceramic
-Epoxy Putty Sticks
-Fibreglass
-Metal
-Plastic/Composite/PVC
-Under Water/Wet
-And More
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Improve energy efficiency and protect your pipes with K-Flex Self Adhesive Pipe Insulation Tape. Designed to prevent heat loss and condensation, this high quality insulation tape provides a secure, long lasting seal around hot and cold water pipes, air conditioning lines, and refrigeration systems. The self adhesive backing makes installation quick and mess free, ensuring a tight bond without the need for extra adhesives or fasteners.
Key Features
Reduces heat loss in hot water and heating pipes
Prevents condensation and moisture build up on cold pipes
Self adhesive for easy and fast installation
Durable closed cell elastomeric foam construction
Excellent thermal insulation and flexibility
Suitable for copper, steel, and plastic pipes
Resistant to mould, mildew, and environmental wear
Best For
Insulating hot and cold water lines
Preventing energy loss in heating systems
Air conditioning and refrigeration pipework
Reducing condensation on exposed pipe surfaces
Improving system efficiency in residential and commercial buildings
Product Specifications
Brand
K-Flex
Product
Self Adhesive Pipe Insulation Tape
Material
Elastomeric foam
Adhesive Type
Pressure sensitive acrylic adhesive
Colour
Black
Temperature Range
-40°C to +85°C
Applications
Thermal insulation, condensation control, energy saving
Water Absorption
Low, closed cell structure resists moisture
How To Use
Ensure the pipe surface is clean, dry, and free from dust or oil.
Peel away a section of the backing paper to expose the adhesive.
Wrap the tape tightly around the pipe, overlapping each layer by at least 10 mm.
Press firmly to ensure full adhesion and an airtight seal.
Trim any excess tape with a sharp blade for a clean finish.
Tips
For maximum efficiency, insulate all exposed pipe joints and fittings.
Use in conjunction with K-Flex insulation tubing for full coverage.
Store in a cool, dry place when not in use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Kwik Grip Crystal Clear applies clear and dries crystal clear for less mess and invisible bond lines. Excellent for achieving a neat, clear finish when bonding large, flat close-fitting surfaces such as veneers and laminates for bench or table tops. Forms a durable, heat and water-resistant bond.
Features
Solvent based contact adhesive
Applies clear and dries crystal clear
Strong, durable bond on broad surfaces
Easy to spread
Heat resistant – up to 80°C
Water resistant
Where can this product be used?
Applications where invisible bond lines are needed such as adhering decorative strips to a mirror
Bonding veneers of timber and laminated plastics (e.g. Laminex and Formica) to bench or table tops
Patching vinyl flooring or replacing a vinyl tile
Cork tiling and laying a vinyl floor
Fixing shoes or laminate to tables, benchtops, etc.
Leather shoe and leather repairs, handbags, and leather work
Adhering flexible or other materials to aluminium
Joining or repairing holes in tents, car covers, and other outdoor equipment
Seek advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Waterbased is safe to use for all these applications and will provide excellent bonding.
Not suitable for bonding rough, ill-fitting surfaces. Consider using alternative products such as Selleys Liquid Nails for these applications.
What materials is this product suitable for?
Veneers
Rubber
Cork
Felt
Leather
Canvas
Metals
Timber
How to use this product
Use only in a well-ventilated area.
Contact Bonding
Hold down lid while opening can.
Ensure surfaces are clean and dry. For porous surfaces, apply a thin coat to seal surface and allow to dry for approx. 40 minutes.
Using an applicator, completely cover both surfaces with adhesive and keep apart until touch dry (approx. 15 minutes, no more than 30 minutes).
Position items carefully, still keeping surfaces apart with dowels. When edges are perfectly aligned, remove dowels and press surfaces firmly together from one edge to the other.
Secure the bond by running a roller over the bonded surfaces or by hammering from the centre outwards using a padded block.
Maximum bond strength is reached after 24 hours. Clamping may be necessary for warped or curled surfaces.
Wet Bonding (for small areas or porous surfaces)
Ensure surfaces are clean and dry.
Apply Kwik Grip to one surface, then bring the surfaces together and clamp until dry.
Handy Tips
Test plastics before use as solvents may attack some polystyrene and sheet vinyls.
500mL covers up to 2.5m² of one surface, depending on porosity.
For vertical surfaces use Selleys Kwik Grip Vertical Gel.
For confined or low-ventilation areas, use Selleys Kwik Grip Waterbased, which is non-toxic and fume-free.
Use a brush, knife, or serrated scraper for application.
Bonding is immediate once the two surfaces are joined.
Keep container sealed when not in use.
Surface Preparation and Cleanup
For porous surfaces, clean with Selleys Liquid Sugar Soap.
For non-porous surfaces (e.g. glass or metal), clean with mineral turpentine followed by methylated spirits.
For old paint or residue, use Selleys Kwik Strip Smart and ensure surface is dry before applying adhesive.
While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove.
Tools can be cleaned by soaking in toluol or lacquer thinner.
Keep Selleys Sugar Soap Wipes handy for quick cleanup.
Safety: Contains highly flammable solvents. Ensure all fire precautions are observed. As an alternative, Kwik Grip Waterbased is non-flammable.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A heat resistant, solvent-based, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces.
Features;
Heat resistance up to 130C
No clamping required
Suitable for interior and exterior jobs
Cured adhesive is resistant to dilute acids and alkalis
Grabs immediately on contact
Easy to spread
Appearance:
Yellowish to beige coloured opaque liquid with strong solvent odour.
Where can this product be used?
Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops
Areas where clamping or pressing facilities are either not available or difficult to use
Patching vinyl flooring
Replacing a vinyl tile
Cork tiling
Laying a vinyl floor
Fixing shoes
Fixing laminate to tables, benchtops etc
Leather shoe and leather repairs, leather work eg handbags
Repairing tents and outdoor equipment
Adhering flexible or other material to Aluminium
Joining, repairing holes in tents, car covers and other outdoor equipment
Attaching rubbers to your fridge door
Repairing your wetsuit
Some plastics such as vinyl sheeting and polystyrene are attacked by Kwik Grip Solvent. Test in an inconspicuous area prior to application.
Seek the advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Advanced is safe to use for all these applications and will provide excellent bonding.
Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Advanced is non-flammable.
Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications).
What materials is this product suitable for?
Cork
Rubber
Felt
Canvas
Leather
Metals
Timber
Laminated plastics (laminex, formica)
Hardboard
Compressed board
How to use this product:
When bonding laminated plastics, ensure that surfaces to be bonded are clean, dry and free from grease or paint.
Surfaces to be bonded should be relatively smooth and/or close fitting.
Both surfaces should be completely covered with adhesive and kept apart till “touch dry” – no more than 40 minutes.
Position the items carefully, still keeping surfaces apart. Remember once joined they cannot be repositioned. When edges are perfectly aligned, press surfaces firmly together.
Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block.
For bonding other materials, apply as for laminated plastics above.
When small surface areas are to be joined a wet bond may be used. Simply apply Kwik Grip Solvent to one surface then bring the surfaces together and clamp until dry.
Handy tips:
-Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls.
-Up to 5sq.m/litre (bonded area 2.5sq.m/litre) depending on the porosity of surfaces.
-For vertical surfaces, we recommend using SELLEYS Kwik Grip Gel Vertical.
-For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes.
-Use a brush, knife or serrated scraper for application.
-When using the contact method REMEMBER bonding is immediate once the two surfaces are joined.
-Keep container sealed when not in use.
-For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
-While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Horizontal has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent.
-Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips:
-Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. We recommend you use Kwik Grip Waterbased in these circumstances.
-Highly flammable. Do NOT use in the same area as flame, fire or spark producing apparatus or machinery.
-This product should not be accessible to juveniles, because of its solvent content. Intentional misuse by deliberately inhaling vapours from this product can be harmful or fatal.
-Contact with skin and eyes should be avoided and avoid breathing vapour.
-If in eyes flush with plenty of water for 15 minutes and seek medical advice.
-If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do NOT induce vomiting. Give a glass of water and seek medical advice.
-For further information refer to the Safety Data Sheet (MSDS).
Storage and re-use
Store in a cool area away from ignition sources and out of direct sunlight.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results.
Features
High Strength (Stronger than Kwik Grip or Kwik Grip Gel)
Easy to use – Applies white, and turns clear when ready to join surfaces
Easy to clean up – Cleans up with water
Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car.
Dries clear – For seamless repairs
Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required)
Suitable for use on horizontal or vertical surfaces
Can be used in same method as other adhesives (wet bond) for small repairs.
Heat resistant to 130oC
Non-flammable
Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity
Where can this product be used?
Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture.
Areas where clamping or pressing facilities are either not available or difficult to use.
Patching vinyl flooring
Replacing a vinyl tile
Cork tiling
Laying a vinyl floor
Leather work eg handbags
Adhering flexible or other material to Aluminium
Joining, repairing holes in tents, car covers and other outdoor equipment
Replacing lifting edges or laying lino
Attaching rubbers to your fridge door
Bonding labels to tins
Repairing your wetsuit
Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use
What materials is this product suitable for?
Fabric
Laminated plastics
Veneers
Hard board
Polystyrene foam
Fibrous cement sheet
Aluminium
Polyurethane foam
Rubber
Cork
Leather
Canvas
Felt
Metals
Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue )
How to use this product
General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp.
Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc.
Contact bonding:
1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles.
2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart
3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact.
4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours.
Note: Drying time may be extended in cold and wet weather conditions. Wet bonding:
Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles.
Apply to one surface then bring surfaces together and clamp until dry.
Clean up application tools and excess adhesive with damp cloth & water before it dries.
Handy tips
What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required)
Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based..
Can be used on horizontal or vertical surfaces
In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours.
What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results.
Features
High Strength (Stronger than Kwik Grip or Kwik Grip Gel)
Easy to use – Applies white, and turns clear when ready to join surfaces
Easy to clean up – Cleans up with water
Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car.
Dries clear – For seamless repairs
Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required)
Suitable for use on horizontal or vertical surfaces
Can be used in same method as other adhesives (wet bond) for small repairs.
Heat resistant to 130oC
Non-flammable
Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity
Where can this product be used?
Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture.
Areas where clamping or pressing facilities are either not available or difficult to use.
Patching vinyl flooring
Replacing a vinyl tile
Cork tiling
Laying a vinyl floor
Leather work eg handbags
Adhering flexible or other material to Aluminium
Joining, repairing holes in tents, car covers and other outdoor equipment
Replacing lifting edges or laying lino
Attaching rubbers to your fridge door
Bonding labels to tins
Repairing your wetsuit
Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use
What materials is this product suitable for?
Fabric
Laminated plastics
Veneers
Hard board
Polystyrene foam
Fibrous cement sheet
Aluminium
Polyurethane foam
Rubber
Cork
Leather
Canvas
Felt
Metals
Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue )
How to use this product
General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp.
Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc.
Contact bonding:
1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles.
2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart
3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact.
4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours.
Note: Drying time may be extended in cold and wet weather conditions. Wet bonding:
Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles.
Apply to one surface then bring surfaces together and clamp until dry.
Clean up application tools and excess adhesive with damp cloth & water before it dries.
Handy tips
What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required)
Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based..
Can be used on horizontal or vertical surfaces
In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours.
What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T22 SCREWLOCK
Low Strength for Easy Disassembly - 50ml
Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance.
Applications
T22 is specifically formulated to lock and seal small screws (less than ¼), including set screws with long engagement lengths.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry for optimal results.
If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole.
Assemble components and tighten to the required torque level.
Allow to fully cure before applying load.
Properties of Uncured Material
Chemical Type: Anaerobic
Colour: Purple
Toxicity: Low
Solid Content: 100%
Viscosity @ 25°C, cPs: 900-1,500 cps
Specific Gravity: 1.05
Shelf Life: 24 months
Performance of Cured Material
Fixture Speed: 15-20 Min @ 22°C
Full Cure: 24 Hours @ 22°C
Temperature Range: -50°C to 150°C
Product Conformity: MIL-S-46163A, ASTM D-5363, NSF
Technical Datasheet
The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm 9Nm on 3/8 plain steel nut & bolt after 1 hour and 5Nm 11Nm after 24 hours. On a 3/8 zinc nut & bolt, the strength is 1Nm 4Nm after 24 hours.
Environmental and Fluid Resistance
Heat Age: 100% retention in Engine oil @ 150°C
Brake Fluid @ 150°C: 85% retention
ATF @ 150°C: 85% retention
50/50 water/ethylene glycol @ 120°C: 80% retention
Water @ 100°C: 80% retention
Gasoline @ 25°C: 95% retention
Diesel Fuel @ 25°C: 100% retention
Ethyl Alcohol @ 25°C: 90% retention
Active & Inactive Metal Table
Category
Cure Speed
Metals
Super Active
Very Fast Cure
Brass, Copper, Magnesium
Active
Fast Cure
Iron, Steel, Nickel, Aluminium
Inactive
Slow Cure
Stainless Steel, Titanium, Zinc
Passive
Primer Necessary
Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch.
Recommended on
Low strength
Stops vibration loosening of screws and seals against leakage
Prevents thread corrosion
Dismantle with normal hand tools
How to Use:
Step 1: Safety Precautions
Keep out of reach of children.
Step 2: Preparation
Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface.
Step 3: Application
For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area.
For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole.
For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours.
Step 4: Cleanup
Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush.
For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T43 NUTLOCK
Medium Strength (Oil Tolerant) - 50ml
Description: HOLDIT AUSTRALIA T43 Nutlock is an oil tolerant, medium viscosity, Thixotropic, anaerobic thread locking adhesive suitable for all types of metal threaded fasteners. The cured adhesive offers controlled medium strength, excellent temperature, and solvent resistance, particularly against water and nonpolar solvents. It rapidly cures on plated, oily metal surfaces or inactive surfaces.
Applications
Ideal for replacing lock washers and plastic inserts, NUTLOCK locks machine tool access bolts, studs, hydraulic system bolts, gear box bolts/drive shaft, bearing cover cap screws, counter sunk screws, conveyor roller bolts, and is suitable for construction equipment.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry for optimal bonding.
If metal is inactive or cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply adhesive to the fixing position of the fastener or onto the internal threads of a blind hole.
Assemble components and tighten to the required torque level.
Allow the adhesive to fully cure before applying load.
Active & Inactive Metal Table
Please consult the Active and Inactive Metal Table for specific application guidance.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies.
LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids.
Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces).
Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids
Permits disassembly with hand tools for servicing
Technology: Acrylic
Chemical Type: Dimethacrylate ester
Appearance (uncured) Blue liquidLMS
Fluorescence Positive under UV lightLMS
Components One component -
requires no mixing
Viscosity Medium, thixotropic
Cure Anaerobic
Secondary Cure Activator
Application Threadlocking
Strength Medium
LOCTITE® 243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE® 243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids
GENERAL INFORMATION
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS).
Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive.
This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates.
Directions for use:
For Assembly
1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator.
Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed
3. Shake the product thoroughly before use
4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application
5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area
6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole
7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also
8. Assemble and tighten as required
For Disassembly
1. Remove with standard hand tools
2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot
3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot
For Cleanup
1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia STUDLOCK
Mid Strength Lubricated for Torque Assembly - 50ml
Description: HOLDIT AUSTRALIA T62 Lubricated Thread Locker is a medium strength, anaerobic thread locking compound, perfect for permanent locking of threaded fasteners. T62 is effective on aluminium, steel, plated, stainless steel, and special alloy parts. It is characterized by its good temperature and solvent resistance.
Applications
Designed for locking and sealing large fasteners (1 and larger), T62 is ideal for applications where shock and vibration may cause fasteners to loosen, ensuring a stable and permanent lock.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry for optimal adhesion.
If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole.
Assemble components and tighten to the required torque level.
Allow the adhesive to fully cure before applying any load.
Active & Inactive Metal Table
Consult the Active and Inactive Metal Table for specific application guidance on different metal types.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids.
Recommended on
High strength
Locks studs against vibration loosening
Controlled/torque tension
Prevents thread corrosion
Fast curing
How to use:
Step 1: Safety Precautions
Keep out of reach of children.
Step 2: Preparation
Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface.
Step 3: Application
For Thru Holes:
Apply several drops of the product onto the bolt at the nut engagement area.
For Blind Holes:
Apply several drops of the product down the internal threads to the bottom of the hole.
For Sealing Applications:
Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours.
Step 4: Cleanup
Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush.
For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
Directions for use:
For Assembly
1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry
2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed
3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application
4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area
5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the
blind hole
6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also
7. Assemble and tighten as required
For Disassembly
1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup
1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T71 THREADLOCK
High Strength, Low Viscosity - 50ml
Description: HOLDIT AUSTRALIA T71 Threadlock is a high-strength, anaerobic thread locking compound. T71 is developed for the permanent locking of threaded fasteners and performs well on aluminium, steel, plated fasteners, stainless steel, and special alloy parts. It boasts good temperature stability and solvent resistance.
Applications
T71 is designed to lock and seal large fasteners, especially in applications where shock and vibration might cause loosening. Its high strength ensures a reliable lock in demanding environments.
Instructions for Use
Clean all surfaces with a cleaning solvent and let them dry.
If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or to the internal threads of a blind hole.
Assemble the components and tighten to the required torque level.
Allow the adhesive to fully cure before applying load.
Active & Inactive Metal Table
Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium
Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel
Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T72 STUDLOCK
High Temp High Strength for Bolts 25mm and Above - 50ml
Description: HOLDIT AUSTRALIA T72 Studlock is a High Strength-High Temperature Threadlocker. This red, single component, anaerobic adhesive is ideal for joining threaded parts exposed to operating temperatures up to 232°C. Its enhanced chemistry allows superior performance at temperatures significantly higher than other thread locking products.
Applications
T72 is perfect for high-temperature locking and sealing of studs, nuts, screws, bolts, and fittings. It effectively locks and seals parts against leakage, contamination, and corrosion, particularly suitable for larger diameter, coarse-threaded parts. Recommended for components not requiring routine maintenance, as disassembly can be challenging and may require heat.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry.
If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole.
Assemble components and tighten to the required torque level.
Allow the adhesive to fully cure before applying load.
Active & Inactive Metal Table
Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium
Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel
Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T77 STUDLOCK
High Strength for Bolts 25mm and Above - 50ml
Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases.
Applications
Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry.
If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole.
Assemble components and tighten to the required torque level.
Allow the adhesive to fully cure before applying load.
Active & Inactive Metal Table
Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium
Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel
Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T90 PENETRATOR
Wicking Grade for Close Fitting Parts - 50ml
Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies.
Applications
T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry.
If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts.
Assemble components and tighten to the required torque level.
Allow the adhesive to fully cure before applying load.
Active & Inactive Metal Table
Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium
Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel
Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 290 is a medium/high strength, wicking grade threadlocking adhesive that is ideal for locking preassembled fasteners.
LOCTITE® 290 is a liquid medium/high-strength threadlocker designed for the locking and sealing of threaded fasteners. Because of its low viscosity and capillary action, the product wicks between engaged threads and eliminates the need for disassembly prior to application. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The product can also fill porosities in welds, castings and powdered metal parts.
Ideal for locking preassembled fasteners, e.g. instrumentation fasteners, electrical connectors and set screws
Works on metal only
Proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids
Requires heat for disassembly
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bonds metals, ceramics, concrete, fibreglass, marble and wood. Syringe dispenser accurately measures equal amounts of resin and hardener to prevent wastage. Fast curing, cure commences in five minutes and reaches full cure in one hour. When cured, the bond is transparent and virtually colourless.
Loctite 5 Minute Epoxy Adhesive's premium formulation is solvent-free and 100% solids providing a non-shrink, environmentally friendly bond. High viscosity provides a good gap-filling ability.
DIRECTIONS FOR USE:
1. Surfaces must be clean and dry. If possible, roughen surface with sandpaper to improve keying and bonding.
2. Cut tips of twin nozzle with a sharp knife and remove nozzle cap from syringe plunger.
3. Push the twin plunger to squeeze out equal amounts of resin and hardener in the amounts required. 4. Mix the resin and hardener for one or two minutes until the colour is completely uniform.
5. Apply immediately to both surfaces and press together. Pressure clamping is not necessary, but allow the adhesive to set for at least 5 minutes before moving. Remove any excess adhesive immediately. 6. Important. After dispensing product be certain to insert plug supplied in the nozzle of the syringe to prevent waste. Preferably store in an upright position as packaged.
Structural Bonding - Fast Cure.
Sets in 5 minutes. Sets in 5 minutes. Good chemical resistance.
Fixture time: 4-6 min
Temperature Resistance: Up to 180°F (82°C)
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates.
LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs.
Universal instant adhesive
Very high strength on close-fitting parts
Perfect for all quick repairs and all types of small emergency repairs.
Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics)
Technical Information
Colour Clear: Ultra Clear
Fixture Time 3 - 10 sec.
Full Cure Temperature 77 °F
Gap Fill 0.15 mm
Key Characteristics General Purpose, Viscosity: Low Viscosity
Shear Strength Unit, Grit Blasted Steel psi
Shear Strength, Grit Blasted Steel 3200
Specific Gravity 1.05 g/l
Specific Gravity Temperature 25 °C
Temperature -65 - 250 °F
Viscosity 110 mPa.s (cP) Brookfield
Viscosity Temperature 77 °F
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates.
LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs.
Universal instant adhesive
Very high strength on close-fitting parts
Perfect for all quick repairs and all types of small emergency repairs.
Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics)
Technical Information
Colour Clear: Ultra Clear
Fixture Time 3 - 10 sec.
Full Cure Temperature 77 °F
Gap Fill 0.15 mm
Key Characteristics General Purpose, Viscosity: Low Viscosity
Shear Strength Unit, Grit Blasted Steel psi
Shear Strength, Grit Blasted Steel 3200
Specific Gravity 1.05 g/l
Specific Gravity Temperature 25 °C
Temperature -65 - 250 °F
Viscosity 110 mPa.s (cP) Brookfield
Viscosity Temperature 77 °F
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 406 is a low viscosity, fast curing instant adhesive that is ideal for bonding plastics and elastomeric materials where very fast fixturing is required.
LOCTITE® 406 is an instant adhesive designed especially for the fast bonding of plastics and rubbers. This product offers exceptionally low viscosity. When combined with LOCTITE primers for cyanoacrylates, it can also be used on difficult-to-bond plastics.
Rapid bonding of plastic & rubber, including EPDM
LOCTITE 770 or LOCTITE 7239 primer improves adhesion of difficult-to-bond substrates
Technology Cyanoacrylate
Chemical Type Ethyl cyanoacrylate
Appearance (uncured) Transparent, colorless to straw
colored liquid LMS
Components One part - requires no mixing
Viscosity Low
Cure Humidity
Application Bonding
Key Substrates Plastics and Rubbers
TYPICAL CURING PERFORMANCE
Under normal conditions, atmospheric moisture initiates the curing process. Although full functional strength is developed in a relatively short time, curing continues for at least 24 hours before full chemical/solvent resistance is developed.
Technical Information
Colour Clear: Ultra Clear
Fixture Time 2.0 - 10.0 sec.
Gap Fill 0.05 mm
Key Characteristics Viscosity: Low Viscosity
Substrates Plastic, Rubber
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Black, toughened ethyl-based instant adhesive. Well suited to plastics, rubbers, metals as well as porous/acidic surfaces.
LOCTITE® 438 is a black, toughened ethyl-based instant adhesive. It has a fixture time of 10 - 20 secs., high impact resistance and is flexible. It is suitable for bonding plastics, rubber, metals, porous and absorbent substrates and acidic surfaces. Good resistance in humid environments.
Cures very quickly when confined between two surfaces
Ideal for bonding small to medium-size parts
Excellent adhesion to most substrates
Suitable for rubbers and plastics
Well suited to metals, porous and/or acidic surfaces
Fixture time of 10 - 20 secs.
Solvent-free
Toughened, black
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications.
LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications.
LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs.
Universal instant adhesive gel
Will not drip or run
Non-wicking, especially suited to porous materials
Perfect for all quick repairs
Ideal for overhead application and vertical faces
Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics
Technical Information
Colour Clear: Ultra Clear
Fixture Time 5 - 10 sec.
Full Cure Temperature 77 °F
Gap Fill 0.15 mm
Key Characteristics General Purpose
Physical Form Gel
Shear Strength Unit, Grit Blasted Steel psi
Shear Strength, Grit Blasted Steel 3200
Specific Gravity 1.05 g/l
Specific Gravity Temperature 25 °C
Temperature -65 - 250 °F
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications.
LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications.
LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs.
Universal instant adhesive gel
Will not drip or run
Non-wicking, especially suited to porous materials
Perfect for all quick repairs
Ideal for overhead application and vertical faces
Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics
Technical Information
Colour Clear: Ultra Clear
Fixture Time 5 - 10 sec.
Full Cure Temperature 77 °F
Gap Fill 0.15 mm
Key Characteristics General Purpose
Physical Form Gel
Shear Strength Unit, Grit Blasted Steel psi
Shear Strength, Grit Blasted Steel 3200
Specific Gravity 1.05 g/l
Specific Gravity Temperature 25 °C
Temperature -65 - 250 °F
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
LOCTITE 518 is a medium-strength, general purpose gasketing product with excellent contamination tolerance. Ideal for use on casted iron, steel and aluminum flanges.
LOCTITE® 518 cures when confined in the absence of air between close-fitting metal surfaces. It is an anaerobic gasketing material designed for use on rigid iron, aluminum, and steel flanged mating surfaces. LOCTITE 518 fills gaps up to 0.25mm and forms a flexible, chemical-resistant seal that will not tear or decay. Parts disassemble easily, even after extended service. Typical applications include sealing close-fitting joints between rigid metal faces and flanges. It is also used as a formed-in-place gasket on rigid flanged connections, e.g. transmissions and motor housings.
Semi-flexible, medium-strength anaerobic flange gasket
Easy to automate
Reduces process costs – eliminates manual assembly of conventional gaskets
NSF P1 Reg. No. 123758
For active and inactive rigid metal flanges
Cures through minor surface contamination
Adapts to flange surface irregularities and gaps up to 0.25 mm
Gel-type consistency
Seals instantly against low pressure
Reduces inventory costs – no need for large inventory of cut gaskets
Resists high pressure when fully cured
No compression set or misaligned gaskets
Technical Information
Applications Rigid Assembly Gasketing
Colour Red
Cure Schedule Temperature (Step 1) 200
Cure Schedule Temperature Unit (Step 1) °C
Fixture Time 25 min.
Fixture Time Temperature 25 °C
Full Cure Temperature 77 °F
Gap Fill 0.3 mm
Shelf Life Temperature -40 °C
Specific Gravity 1.1 g/l
Specific Gravity Temperature 25 °C
Substrates Metal: Aluminum
Temperature -65 - 300 °F
Tensile Shear Strength 7.5 N/mm²
Viscosity 500000 - 1000000 mPa.s (cP) Brookfield
Viscosity Temperature 77 °F
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing.
LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.
Ideal for fine threads as used in hydraulic, pneumatic & general fittings
Suitable for metal threads only
Instant low-pressure seal
Resistant to fuel, oil, coolants and hydraulic fluids
Locks connection against vibration loosening
PRODUCT DESCRIPTION
LOCTITE® 542 provides the following product characteristics:
Technology Acrylic
Chemical Type Dimethacrylate ester
Appearance (uncured) Brown liquidLMS
Components One component -
requires no mixing
Viscosity Low
Cure Anaerobic
Secondary Cure Activator
Application Thread sealing
Strength Medium
Directions for use:
For Assembly
1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry.
3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations.
5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours.
For Disassembly
1. Remove with standard hand tools.
2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot.
For Cleanup
1. Cured product can be removed with a combination of soaking in a Loctite solvent and mechanical abrasion such as a wire brush.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
When you have a minute - tackle even big repairs with the new Loctite 60 seconds All-Purpose Glue. It is fast, strong and repositionable. Perfect results in only 60 seconds.
Recommended on:
Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic*.
Properties:
-Fast: it bonds materials within ca. 60 seconds
-Extra strong: it builds up a strength of 100+ kg/cm² within a short time
-Repositionable: it gives time to reposition the parts that you want to glue
-Ideal for all home repairs, even mid-size and large surfaces
-Non-drip gel formula, suitable for vertical applications
-It dries transparent
-Suitable for use on most surfaces*
-Solvent-free
-Perfectly bonds non-porous to non-porous materials
*Except polyethylene (PE), polypropylene (PP), PTFE, glass, Styropor® and synthetic fibres
Step by Step:
1.Ensure surfaces to be bonded are clean, completely dry and close-fitting.
2.Twist the cap/nozzle clockwise onto the tube and remove the cap.
3.Carefully apply the glue on one surface. Press the surfaces together, reposition it as you wish, then press with strong and even pressure for few seconds and leave it undisturbed for 60 seconds.
4.Clean the nozzle, replace the cap and store upright in a cool dry place.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
High strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts.
LOCTITE® 609 is a green, high strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. The product cures in the absence of air between close-fitting metal surfaces. Typical applications include rotor to shafts in fractional and subfractional horsepower motors. Locks bushings and sleeves in housings on shafts.
Augments press fits.
Low viscosity
Prevents loosening and leakage from shock and vibration
Augments press fits
Tested to the lot requirements of Military Specification Mil-R-46082B (this is a regional approval)
Technical Information
Agency Approvals / Specifications ASTM D5363, CFIA Listed, MIL-R-46082B for existing designs
Application Method Pressure
Applications For Close Fitting Parts, Retaining
Colour Green
Cure Type Anaerobic Cure
Diametrical Clearance (Maximum) Unit in.
Fixture Time 10 min.
Fixture Time Temperature 10 °C
Full Cure Temperature 22 °C
Full Cure Time 24 hr.
Gap Fill 0.006 in.
Key Characteristics Fluorescent, Strength: High Strength, Viscosity: Low Viscosity
Number of Components 1 Part
Physical Form Liquid
Shear Strength Unit, Steel psi
Shear Strength, Steel 2300
Specific Gravity 1.1 g/l
Specific Gravity Temperature 25 °C
Substrates Metal
Technology Acrylic
Temperature -65 - 300 °F
Viscosity 125 mPa.s (cP) Brookfield
Viscosity (#7sp/20/rpm) 125 mPa.s (cP) Brookfield
Viscosity Temperature 25 °C
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Ash Meranti]](//gluesaustralia.com.au/cdn/shop/files/9300611329301.jpg?v=1754724101&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Cypress Cedar]](//gluesaustralia.com.au/cdn/shop/files/9300611329400.jpg?v=1754724101&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Ash Meranti]](http://gluesaustralia.com.au/cdn/shop/files/9300611329301.jpg?v=1754724101&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Cypress Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9300611329400.jpg?v=1754724101&width=645)
