Professional Use

• 

  View options

  30 ml Adhesive Syringe Blunt Tip Fill Needle

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Get clean, precise application of glues, epoxies, resins, oils, inks, and other liquids with this easy to use 30 ml syringe and blunt tip fill needle. Ideal for workshop, craft room, electronics bench, and on site repair jobs where accuracy matters and mess is not an option. Why you'll like it Controlled dispensing for dots, lines, seams, and small cavities 30 ml capacity for longer runs without constant refilling Graduated barrel with clear volume markings for repeatable dosing Luer lock connection keeps the needle securely attached during use Reusable barrel when used with compatible liquids and cleaned after use Blunt tip needle for safe, non piercing filling and application Common uses Injecting Fix-A-Floor through grout lines to re bond hollow or loose tiles Precision placement of two part epoxies and cyanoacrylate gels Applying PVA wood glue into tight joints and dowel holes Wicking thin adhesives along hairline cracks Filling small voids and seams before clamping Electronics work with flux, solder paste, and conformal coatings Craft, model making, leatherwork, and jewellery repairs Tile repair tip: A blunt tip of about 2 mm to 3 mm fits most grout lines. Drill a small hole in the grout as directed by the adhesive manufacturer, inject until the cavity is filled, then clean any squeeze out promptly. What is included 1 × 30 ml syringe barrel with plunger 1 × blunt tip fill needle with luer lock hub 1 × protective cap for storage Specs Capacity 30 ml Connection Luer lock Needle style Blunt tip, non piercing Barrel material Transparent polypropylene Plunger seal Latex free elastomer Use For adhesives and shop liquids only, not for medical use How to use Attach the blunt tip needle by twisting it onto the luer lock until snug. Pull back the plunger, draw in your adhesive, then tap the barrel to release trapped air. Dispense with slow, steady pressure for consistent beads and dots. For Fix-A-Floor, inject through the grout holes until filled and follow the cure steps on the product label. After use, expel remaining liquid if suitable, then flush the barrel and needle using a cleaner compatible with your adhesive. Dry completely and cap for storage. Compatibility tips Works well with PVA, polyurethane, epoxy, acrylic, latex, and many hobby liquids. For solvent based products, confirm compatibility with polypropylene before use. Do not store reactive two part mixes inside the syringe after they begin to cure. Safety Not sterile and not for medical, food, or body use. Wear gloves and eye protection when handling chemicals. Keep out of reach of children. FAQ Can I reuse itYes, if your adhesive and cleaner are compatible with polypropylene and the luer lock needle. Clean immediately after use for best results. Will it work with thick glueYes, but very thick products may require more pressure and a wider blunt tip size. Does it come sterileNo. This set is for industrial, workshop, and hobby applications only.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $18.00

  View options

• 

  View options

  Timbermate Timbermate Woodfiller putty crack filler Interior

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time."  You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $0.00 - $89.00

  View options

• 

  View options

  Loctite Loctite Super Glue Professional Water Resistant 20g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $23.00

  View options

• 

  View options

  Timbermate Earl's MulTfill Multi-Purpose Paintable Putty Interior & Exterior Filler

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $6.00 - $54.64

  View options

• Last stock!

  View options

  Weldbond Weldbond Steel Tough Welbond Universal Adhesive Tube 3Lt

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $103.00

  View options

• 

  View options

  Sika Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikasil® Pool Neutral-Cure Silicone Sealant – 300 ml Cartridge Designed for use in demanding aquatic environments, Sikasil® Pool is a one-part, neutral-curing silicone sealant formulated specifically for swimming pools, wet areas, and permanently submerged joints. With exceptional resistance to chlorinated water, high elasticity, and outstanding fungal resistance, this sealant delivers durable, long-lasting performance. Key Features Excellent resistance to chlorinated water and common pool chemicals Movement accommodation of ± 25 % Neutral cure — non-corrosive, safe on most metals and tile systems High elasticity and recovery Very good resistance to fungal attack Suitable for interior and exterior applications Typical Applications Underwater joints in swimming pools Wet areas, such as spas, splash zones, and shower recesses Sealing between tiles, concrete, glass, and metal substrates Technical Highlights Service temperature range: –40 °C to +80 °C Shore A hardness (28 days): ~20 Elastic recovery: > 90% Typical curing speed: ~2 mm per 24 h Skinning time: ~5 minutes (23 °C / 50% RH) Available in White, Grey, and Transparent shades Shelf life: 15 months (when stored unopened between 5 °C and 25 °C) Usage & Application Tips Ensure surfaces are clean, dry, and free from contaminants (oil, dust, grease). Roughen smooth, non-porous surfaces (e.g. metal, glazed tile) before application. Use appropriate primers (e.g. Sika Aktivator-205, Primer-3 N) on metals, PVC, or porous substrates as recommended. Apply a closed-cell foam backing rod to control joint depth. Insert sealant by cartridge gun, avoiding air entrapment. Tool the bead within the skin formation time. Allow full cure (minimum 7 days) before filling pool with water. Limitations & Precautions This product is not suitable for: Joints in direct contact with potable food or drink Overpainting Use on substrates that leach oils, plasticisers or solvents (e.g. bitumen, EPDM rubber) Always consult the current Product Data Sheet (PDS) and Safety Data Sheet (SDS) for full technical, safety, and application details before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $29.76 $0.10/ml

  View options

• 

  View options

  Selleys Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $0.00 - $20.16

  View options

• 

  View options

  Sika Sikaflex 291 Tube Black Marine-Grade Polyurethane Sealant 150ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance. Features & Benefits Marine-grade polyurethane formula with superior adhesion Excellent weathering and saltwater resistance Elastic and vibration-resistant for long-lasting seals Low odour and non-corrosive composition Can be sanded and overpainted after curing Maintains flexibility across wide temperature ranges Where to Use Sealing and bonding on boats, yachts, and marine structures Deck fittings, hatches, and hardware installations Elastic, vibration-resistant joints above and below deck Bonding wood, metals, primers, coatings, ceramics, and GRP plastics Important Notes Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate Surfaces must be clean, dry, and free from grease or dust before application Recommended application temperature: 5°C to 40°C Technical Details Chemical Base 1-component polyurethane Colour Black Cure Mechanism Moisture-curing Density (uncured) Approx. 1.3 kg/L Shore A Hardness 40 Tensile Strength 1.8 MPa Elongation at Break 500% Temperature Resistance -50°C to +90°C (up to 180°C short term) Skin Time Approx. 60 minutes Shelf Life 12 months (stored below 25°C) Packaging 150 mL Tube For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $19.27 $0.13/ml

  View options

• 

  View options

  Selleys Selleys Araldite Super Strength Epoxy Adhesive Holds 150kg Big Pack x 200ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Araldite Two-Part Epoxy Adhesive delivers maximum strength bonding for a wide range of materials. The mixed product gels in 2 hours, achieves initial bonding within 6–8 hours, and reaches full strength after 3 days. Features Chemical reaction of the two parts provides superior strength Bonds a wide variety of surfaces Dries clear for a clean finish Extremely strong and durable Highly water resistant – suitable for fixing tiles around pools (not below the waterline) Forms a rigid, long-lasting bond Fills small gaps – surfaces do not need to fit perfectly Excellent chemical and heat resistance Clamping recommended for a stronger bond Not suitable for Polypropylene or Polyethylene plastics Bond strength weakens above 80°C but recovers when cooled Appearance Translucent Where to Use Load-bearing repairs Fixing loose table or chair legs Reattaching hammer heads Bonding aluminium sheets Timber repairs on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets or skis Securing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastic (except Polyethylene and Polypropylene) Crystal Leather Directions for Use Ensure all surfaces are clean, dry, and free of grease, rust, and paint. For best results, roughen smooth surfaces after cleaning. Dispense equal parts of Part A and Part B onto a clean, disposable surface (e.g. polyethylene or cardboard). Mix thoroughly using a spatula, nail, or stick. Apply immediately to both surfaces and press together. Clamp for 6–8 hours while the bond sets. Remove excess adhesive and clean tools immediately. Replace the correct caps on each tube to prevent hardening. Handy Tips Mix in small quantities for maximum working time – larger mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover. Do not swap caps between tubes – lids and tubes are colour coded. Uncured Araldite can be wiped off with acetone or nail polish remover. Once cured, remove mechanically by scraping or sanding – solvents will not dissolve it. To reposition a cured bond, heat gradually to 150°C (if the item is heat resistant), reposition, and allow to cool. For surface prep: use Selleys Liquid Sugar Soap on porous materials, or Methylated Spirits on non-porous surfaces. Use Selleys Kwik Strip Smart to remove tough residues if needed. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapours. Do not use solvents near eyes or open wounds. In case of eye contact, rinse with water for at least 15 minutes and seek medical advice. Non-toxic once fully cured. Refer to the Material Safety Data Sheet for more details. Storage & Reuse Ensure caps are replaced tightly after use and store in a cool, dry place.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $76.88

  View options

• 

  View options

  PC Products PC11 Waterproof Marine White Epoxy cures underwater Syringe 28g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $16.24

  View options

• 

  View options

  Loctite Loctite Super Glue ALL PLASTICS 4ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $10.67

  View options

• 

  View options

  Selleys Araldite Ultra Clear Epoxy Adhesive Dries Crystal Clear Holds Up to 130Kg Ideal for Glass 24ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts. -Bonds a variety of surfaces -Dries Crystal Clear so there’s no visible evidence of repair -Quick setting in 5 minutes -No clamping necessary -High water resistance -Forms a rigid, durable bond -Can be used for gap filling (Surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Doesn’t yellow over time so is ideal for use on glassware Appearance: Crystal Clear Where can this product be used? -Fixing a broken glass vase -Repairing jewellery -Toy repairs -Fixing ornaments or crockery -Fixing your handbag strap -Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic -Crystal -Leather How to use this product: -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. -When using tube kit, ensure correct caps are replaced on each tube or they will adhere. Handy tips: -A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). -Clamping is recommended for a stronger bond. -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set. Storage and re-use: Ensure caps or lids are replaced and product stored in a cool dry place.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $21.85

  View options

• 

  View options

  Loxeal Loxeal 58-11 Thread Sealant Anaerobic Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Loxeal 58-11 Anaerobic Thread Sealant Loxeal 58-11 is a high performance anaerobic sealant designed for metal thread joints only. It replaces PTFE tape and cord, delivers instant sealing against moderate pressure, and cures to form a shock and vibration resistant seal that remains reliable from -55°C to +150°C. Why choose Loxeal 58-11 Instant sealing against moderate pressure to get systems back in service fast. Thixotropic formulation stays where you put it and resists migration on threads. Wide chemical compatibility including gas, water, LPG, hydrocarbons, oils and more. Shock and vibration resistant for durable, leak free joints. Temperature range from -55°C to +150°C for tough Australian conditions. Certified and approved Gas approvals: DVGW and DIN EN 751-1, plus Australian Gas Association for working pressure up to 20 bar. Oxygen service: Approved for gaseous oxygen up to 10 bar at +60°C. Potable water: WRAS listed and suitable for contact with wholesome water. Also approved for contact with drinking water by Global Mark. Food area use: NSF registered category S4 for use as an adhesive in and around food processing areas. Hydrogen: Tested by KIWA as a sealant for use with pure hydrogen to EN 751-1. Typical applications Sealing tapered and parallel metal threaded fittings in plumbing, HVAC, gas and hydraulic systems. Replacing PTFE tape or thread cord on metal pipework where a permanent, pressure resistant seal is needed. Directions Clean and degrease threads thoroughly. Cut the nozzle to the required bead size. Apply a continuous bead 1 to 2 threads back from the leading edge. Ensure full coverage around the circumference. Assemble and tighten the joint. Wipe away excess uncured material. Allow to cure (see Cure times). Cure speed can be accelerated on passive metals or at low temperature with an appropriate activator. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Time to water service for potable water systems at +21.1°C Brass, copper, cast iron: 24 hours Stainless steel, aluminium: 7 days Technical data Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity at +25°C 20,000 to 80,000 mPa·s, thixotropic Specific gravity Approx. 1.1 g/ml Gap filling Up to 0.30 mm (M56 / 2 inch) Flash point Greater than +100°C Shear strength 6 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 24 N·m (ISO 10964) Prevailing torque 7 to 14 N·m (ISO 10964) Service temperature -55°C to +150°C Shelf life 1 year in unopened packaging at ? +25°C Chemical resistance Excellent resistance to motor oil, gearbox oil, gasoline and hydraulic oil. Excellent to good resistance in 50 percent water glycol at elevated temperature. Limitations and notes For metal to metal threaded joints only. Not suitable for plastic threads or rubber components. Liquid product can attack some coatings and plastics. Pre test if unsure. For disassembly, use normal tools. Heat components to approximately +150°C to +250°C if required, then remove cured residue mechanically and clean with solvent. Store in a cool, dry place at or below +25°C. Do not return unused product to the bottle. All technical information is provided as a guide only. Always verify suitability with your specific materials, operating pressures and local regulations before use. Follow all safety and handling instructions on the product label and safety data sheet.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $18.77

  View options

• 

  View options

  Dunlop Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $16.30 - $20.18$0.03/g

  View options

• 

  View options

  Selleys Selleys No More Gaps Coloured Caulk Sealant 450g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  No More Gaps Coloured Gaps No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability. Key Features Long-lasting, colour-matched finish Suitable for Interior & Exterior use Available in a great colour range, with no need to paint over (Paintable if required) Superior flexibility to cope with building movement, hiding cracks and gaps longer Greater than 350% elongation/stretch and up to +/- 20% movement capability Good resistance to weathering Superior adhesion to a broad range of surfaces, resulting in a lasting finish Mould and mildew resistant Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles (not exposed to water) In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How to Use Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk. Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun. Hold the caulking gun at a 45° angle and apply, forcing the product into the gap. Smooth with a wet finger or spatula. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured – 72 hours or longer in cold weather. Limitations Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup. When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler. If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth. Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned. Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting. Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup. Clean Up Water-based, so clean up with water. Uncured product may be removed with water. Cured product can be removed by sanding and scraping. Size 450g Cartridge Colours Black Brilliant White Brown Cedar Charcoal Coffee Cream Ivory Light Grey Technology Water-Based Use Interior & Exterior

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $0.00 - $18.72

  View options

• 

  View options

  Sika SikaSeal Appliance Silicone Sealant Thermal Seal 300g Black

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses  Fridge and freezer sealing  Pizza oven sealing  Oven sealing  Aluminium  Glass Characteristics / Advantages  High temperature resistance (-50 - 250°C)  Excellent adhesion  Heat proof  Gap Filling properties  Vibration resistant  Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only. 

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $24.26

  View options

• 

  View options

  Poly Polyfilla F20 Gap Filler - High Flexibility, Superior Durability & Smooth Finish for Interior & Exterior Gaps with Up to 20% Joint Movement

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Polyfilla F20 Gap Filler: The Ultimate Gap Solution for High-Stress Applications Features Highly Durable High Flexibility Smooth Finish +/- 20% Joint Movement Capability Product Description Polyfilla F20 Gap Filler has been specially formulated to offer superior flexibility in high-stress interior and exterior applications. With up to +/- 20% joint movement capability, this gap filler is ideal for filling gaps around cornices, wall joints, skirting boards, as well as window and door frames. Application This product is extremely easy to use. Simply ensure the area is clean and dry, apply the filler, and allow it to dry. It adheres well to multiple surfaces and offers long-lasting results. Use Cases Cornices Wall Joints Skirting Boards Window & Door Frames

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $8.69

  View options

• 

  View options

  PC Products PC Marine Epoxy Putty 15 Minutes Cures Underwater 57g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  PC-Marine™ Epoxy Putty Stick is a specially formulated epoxy putty suitable for wet or underwater applications. Incredibly it has an extended open time (20 – 30 minutes) but cures hard within 60 minutes for a fast return to service and emergency repairs. It sticks great to metals, fibreglass, tile, wood and some plastics such as ABS and rigid PVC. Here are just a few specific uses (there are hundreds of other uses): Seal holes and waterproof fittings Shape and form missing corners or holes in ceramic or fibreglass fixtures Re-attach and secure loose hardware Fill cracks and dings in fibreglass Seal leaks in water tanks How to prepare a surface for bonding with PC-Marine™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Marine™ application Wear disposable gloves to minimize contact with the skin. Use denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner to cleanup before PC-Marine cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying paint remover or paint stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-Marine™ be applied underwater? Yes, application underwater is possible. PC-Marine™ will adhere and cure underwater. However, it is preferable to apply it in dry conditions. Is PC-Marine™ suitable for repairing canoes? PC-Marine™ is excellent for repairs to aluminium and fibreglass canoes but not when they are made with Hypalon. How much time does it take for PC-Marine™ to cure? PC-Marine™ has an extended application or open time of 20 minutes. Most repairs made with PC-Marine™ can be returned to service after 60 minutes. Some applications may require a full 24-hour cure. Is PC-Marine™ green? PC-Marine™ Epoxy Putty stick is white on the inside and green on the outside. The green colour disappears when mixed with the white. The result is an off-white colour when it cures. What is the maximum thickness that PC-Marine™ Epoxy Putty can be applied? PC-Marine™ can be applied thick or thin. There isn’t a thickness limit. It cures from the within via a chemical reaction. It does not need to dry or be exposed to air. How much PC-Marine™ can be mixed at a single time? PC-Marine™ is slower curing than other epoxy putties allowing larger portions to be mixed at one time. Small quantities can be mixed more thoroughly and with less effort. Can PC-Marine™ cure in a freezer? PC-Marine™ is not recommended for sub-freezing temperatures. We recommend an application temperature of 2°C or higher. Does PC-Marine shrink? PC-Marine™ does not shrink.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $16.17

  View options

• 

  View options

  Dunlop Dunlop Tile Adhesive Wall & Floor Indoor & Outdoor 2Kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  This versatile adhesive is specially formulated for fixing most tile types, offering excellent flexibility and suitability for various surfaces. Key Features: Suitable for most tile types Can be applied over a variety of surfaces Suitable for interior timber (with proper preparation) Highly flexible Tile Types: Ceramic tiles Fully vitrified tiles Mosaics Porcelain tiles Natural stone (excluding moisture-sensitive stone) Suitable Surfaces: Cement render and concrete Fibre-cement sheets Existing ceramic and vinyl tiles Dunlop Undertile Waterproofing Metal surfaces Oil-based painted surfaces Plasterboard Indoor timber (must be adequately prepared) Application Areas: Walls and floors Indoor and outdoor use (as long as there’s no standing water and proper water run-off is ensured) Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.8m²/kg 250 x 250mm and larger 10-12mm 0.5m²/kg

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $39.01

  View options

• 

  View options

  Selleys Araldite Super Strenght Expoxy Adhesive Holds Heavy Loads Up to 150Kg 24ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6–8 hours, with maximum bond strength after 3 days. Features Stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries clear Very strong and durable bonding High water resistance (suitable for tiles around pools, but not below the water line  for that use Selleys Knead It Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat resistant Clamping recommended for stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but is regained when temperature drops Appearance Translucent Where Can This Product Be Used? Load-bearing repairs Gluing the head back on a hammer Fixing loose table or chair legs Bonding aluminium sheeting Bonding timber on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets Repairing skis Fixing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastics (except Polyethylene and Polypropylene) Crystal Leather How to Use Ensure all surfaces are clean, dry, and free from grease, rust, or paint. For best results, roughen smooth surfaces after solvent cleaning. Dispense equal volumes of Part A and Part B onto a clean disposable surface (e.g. cardboard or polyethylene) and mix thoroughly. Apply adhesive immediately to both surfaces and press together. Clamp the bond for 6–8 hours while setting. Scrape off excess adhesive and clean utensils immediately. Handy Tips Mix in small quantities for longer working time — large mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover before sealing. Ensure caps are placed on the correct tubes (they are colour-coded). Remove uncured adhesive with acetone or nail polish remover. Once cured, remove by mechanical scraping or sanding — solvents will not dissolve the product. To reposition a cured bond, heat slowly to at least 150°C (if safe for the material), then scrape off excess and reposition carefully. For cleaning surfaces before use: Porous surfaces use Selleys Liquid Sugar Soap Non-porous surfaces (e.g. glass, metal) — clean with methylated spirits For stubborn residue use Selleys Kwik Strip Smart Ensure the surface is dry before applying. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of eye contact, flush with water for 15 minutes and seek medical attention. Non-toxic when set. Refer to the Material Safety Data Sheet (MSDS) for more information. Storage & Reuse Replace caps tightly after use. Store in a cool, dry place.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $24.50

  View options

• 

  View options

  Timbermate Earl's Wood Hardener Water-Based Rotten Timber Consolidator

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Earl’s Wood Hardener - Restore Soft, Rotted Timber Like New Bring weakened, decayed timber back to life with Earl’s Wood Hardener. This water-based consolidator penetrates deep into soft, rotted fibres and bonds them into a tough, stable base that’s ready for filling, sanding, and painting. Use it to save windowsills, frames, posts, decking boards, furniture, fences, and more—without costly tear-outs or replacements. Why Customers Love It Repairs instead of replacing: Restores soft, crumbly timber to near original strength so you can patch and repaint. Water-based formulation: Low odour, no volatile organic compounds, and non-toxic when cured. Ready to use: Pre-mixed; just shake and apply—no diluting or measuring. Works inside and out: Ideal for interior and exterior timber exposed to weathering. Versatile application: Pour, brush, spray, or syringe to saturate deep into affected areas. Long shelf life: Stays usable for extended periods when stored correctly. Proudly Australian made: Developed for local conditions and everyday DIY and trade use. Where to Use Window sills and sashes, door frames, posts, fences, balustrades, fascia boards, decking edges, outdoor furniture, indoor furniture, trims, mouldings—any non-structural timber showing soft rot or fibre breakdown. How It Works The thin, penetrating formula wicks into softened timber fibres. As it cures, it binds those fibres together to form a firm, stable base that can be filled, sanded, and coated. No need to carve out all the rot—thorough saturation does the heavy lifting. Directions Prep: Ensure the area is dry. Remove dirt, dust, grease, loose paint, varnish, and flaky wood. Mask adjacent finishes if needed. Apply: Shake well. Generously pour, brush, spray, or syringe the hardener into the affected timber. Repeatedly saturate to drive product deep into fibres. Cure: Allow to cure until solid and no longer tacky to the touch. Extremely soft timber may need multiple treatments. Repair: Fill voids with a compatible wood filler, let set, then sand smooth. Finish: Prime/seal and paint or coat as desired. Pro Tip For deep penetration around a localized patch of rot, mark approximately 75 mm either side of the soft area and drill small holes between those points. Brush, spray, or syringe the hardener into the holes until saturation is achieved. Clean-Up & Safety Clean tools and drips with water while wet. Use above 7 °C and in well-ventilated areas. Non-toxic when cured. Always follow label directions and keep out of reach of children. Compatibility Once cured, the hardened substrate accepts most timber fillers and putties. After filling and sanding, it can be primed and top-coated with typical timber paints and finishes. Always test on a small area for compatibility. Limitations Not for structural load-bearing repairs. Not recommended for constant water immersion or areas that cannot be dried prior to application. Timber must be reasonably sound after consolidation; heavily degraded material may require multiple treatments or replacement. Specifications Type Water-based timber consolidant / hardener Use Restoring soft, rotted, non-structural timber prior to filling and painting Appearance Low viscosity liquid; dries clear/transparent Odour / VOC Low odour; no volatile organic compounds Application Methods Pour, brush, spray, or syringe to saturate fibres Interior / Exterior Suitable for both Minimum Application Temperature Above 7 °C Cure Indicator Ready for filling when firm and not tacky to the touch Clean-Up Water while wet Shelf Life In excess of 2 years when stored sealed in a cool, dry place Substrates Soft or rotted timber (non-structural), interior and exterior Country of Manufacture Australia Packaging Ready-to-use container What’s in the Box Earl’s Wood Hardener (ready to use) Storage Keep container tightly closed. Store upright in a cool, dry location away from freezing and direct heat. Do not allow product to dry out in the container. Disposal Allow residual product to cure before disposal. Follow local waste regulations. Important Notes Always read and follow the product label before use. Test on a discreet area to confirm adhesion and finish compatibility. The consolidated timber is not structural and should not be relied upon for load-bearing applications.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $25.00 - $160.00

  View options

• 

  View options

  Timbermate Agnews Water Putty - Multi-Purpose Filler & Floor Leveler (Interior/Exterior Grade)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $8.39 - $86.00

  View options

• 

  View options

  Loctite Loctite Super Glue XXL for frequent usage Multi material 20g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $27.65

  View options

• 

  View options

  Selleys Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $0.00 - $20.92

  View options

• 

  View options

  Selleys Selleys Marine Flex For Boats Pools and Spas Water Proof [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $27.66

  View options

• 

  View options

  Selleys Selleys Shoefix Repair Clear Adhesive Flexible Bond 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A strong, weather and impact resistant adhesive that is ideal for most shoe repairs. Features Easy to use Strong Flexible Bond Weather resistant Impact resistant Appearance Dries yellowish/beige Where can this product be used? Sole Tongue Strap Inner sole Attach beads, jewels, decorative items Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles. What materials is this product suitable for? Leather Canvas Fabric Rubber Cork Most Plastics EVA foam (e.g Desert boots sole) How to use this product Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal. For larger area repairs such as shoe soles, we recommend you use the contact bond method: For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes). Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications. For smaller areas, either use the contact method as above, or join with a wet bond: Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry. Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s. Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries. Handy tips A piece of plastic from a takeaway container makes a good applicator for shoe soles. Bulldog clips are handy to use for clamping straps and other small areas. Pack includes a removable nozzle for easy application.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $8.21

  View options

• 

  View options

  PC Products PC11 Waterproof Marine White Epoxy cures underwater Multipurpose 56g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $21.95

  View options

• 

  View options

  Parfix Parfix 4L PVA Wood Glue High Strength Dries Clear

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  This product is a quality PVA glue suitable for general woodworking. It is non-toxic, will not stain timber and dries clear. Suitable for Wood, Particle Board, Unglazed Pottery, Laminating, veneers, paper, cardboard, leather, foam and cloth Directions: Ensure all surfaces are clean, dry and free of oil, grease and wax Shake well before use Only apply to one surface Press surfaces together while the adhesive is still wet and clamp lightly (approx 2 to 4 hours in normal conditions) Remove excess glue with a damp cloth Great strength is achieved when dried overnight Cleaning: Clean up with water. Wash hands after use

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $52.43

  View options

• 

  View options

  Selleys Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $18.00

  View options

• Sale -2%

  View options

  Loctite Loctite Super Glue Glass 3g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Instant, crystal clear bonds that are water and dishwasher-resistant. Formulated to work on all types of glass. Recommended on:Glass, Crystal, Tinted Glass, Glass Works, Opaque Glass, Blown Glass. Properties:Bonds glass to glassGlass to metalStained glassCrystal and tinted glassWater and dishwasher resistantBonds in secondsDries transparent for invisible bondsEasy to open, self-piercing and anti-clog capSolvent-free Step by Step: Ensure surfaces to be joined are clean, completely dry and close fitting Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set Replace the cap immediately and store upright in a cool dry place. How to Repair a Glass Water Jug?Loctite Super Glue Glass has been specially formulated to repair glassware, delivering a sparkling performance every time. Once dry it forms crystal clear bonds on all types of glass breakages and cracks, delivering water and dishwasher resistant seals that are not only neat and free from unsightly white glue marks but also strong enough to resist pressure from temperature changes and water. Loctite Super Glue Glass is designed to work on all kinds of glass: glass, crystal, tinted glass, glass works, opaque glass and blown glass, and has a high strength formula that ensures you get long-lasting durability. Follow the step by step application guide:1.Wash the broken area with water (avoid using detergent as this can affect the glue's performance) and dry thoroughly. Ensure that the surfaces to be joined are close fitting.2.Carefully squeeze a small drop onto one of the broken parts. Press both surfaces together firmly and wait until they is set.3.Do not move until the surfaces are set.  Don’t worry if there is some excess glue, this can be easily removed once dry (see point 5)4.Allow at least 1-2 hours to fully cure before using. For best results leave overnight.5.Once dry, if there is any excess residue, gently wipe with a tissue dipped in Loctite Glue Remover or nail varnish remover containing acetone.6.Replace the cap immediately and store the glue upright in a cool dry place.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $8.95 $8.78

  View options

• Sale -19%

  View options

  Grunt Grunt Flashing Tape for Roofs and Gutters 50mm x 10m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Seal leaks fast and protect exposed joins with Grunt Flashing Tape. This heavy duty self adhesive tape conforms to uneven surfaces, creates a long lasting waterproof barrier, and is ideal for quick fixes and preventative maintenance across roofs, gutters, and outdoor fixtures. Why choose this tape Weatherproof seal that helps stop water ingress at laps, seams, and penetrations. Strong tack for reliable adhesion on metal, plastic, and painted surfaces. Flexible backing that moulds to contours, ridges, and fasteners. UV and outdoor ready for Australian conditions. Clean finish suitable for temporary and permanent repairs. Common uses Sealing gutter joins, end caps, and mitres Flashing around skylights, flues, and vents Stopping drips at roof sheet overlaps Repairing small cracks in downpipes and rainwater fittings Protecting fasteners and exposed fixings from water General waterproofing on caravans, sheds, pergolas, and trailers Surface compatibility Works on most clean, dry, and sound substrates including coated metal roofing, painted timber, rigid plastics, fibreglass, and masonry that has been sealed. Not recommended for silicone contaminated surfaces or areas that remain permanently submerged. How to apply Prepare the area. Remove dust, old flaking coatings, oil, and loose rust. Dry the surface thoroughly. Measure and cut the tape to length with a knife or scissors. Peel and stick. Remove the release liner as you apply, pressing the tape down firmly. Roll with a hand roller or the back of a cloth to eliminate air pockets and ensure full contact. Overlap adjoining pieces by at least 25 mm for a continuous seal. Finish edges with extra pressure. Avoid applying in rain or onto wet surfaces. Pro tips For porous substrates, prime with a suitable primer and allow to dry before taping. Cold weather can reduce tack. Warm the tape and surface slightly to improve bond. Ensure water can shed over the tape rather than against the lap direction. Specifications Brand Grunt Product type Self adhesive flashing and sealing tape Size 50 mm width x 10 m length Use Exterior and interior repairs, roofs, gutters, and general waterproofing Application temperature Apply in dry conditions on clean and sound surfaces Cleanup Wipe tools with mineral turpentine or adhesive remover as suitable for the substrate Frequently asked questions Can I paint over itYes, most solvent based and acrylic paints will adhere. Test a small area first. Is it suitable for potable waterNot intended for potable water contact. Will it work on damp surfacesBest results are achieved on dry surfaces. Dry the area before application.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $15.20 $12.25

  View options

• Sale -18%

  View options

  Paint Parner Paint Partner Thick Masking Tape for Crisp Paint Lines 24mm x 27m - 6 Pack

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Get sharp, clean paint edges with Paint Partner Thick Masking Tape. This reliable painter’s tape is designed to stick firmly, remove cleanly within the recommended time, and resist paint bleed for professional looking results on walls, ceilings, trims, doors, and furniture. Crisp paint lines with reduced bleed on properly prepared surfaces Thicker construction for easy handling, straight tearing, and consistent edging Clean removal within the recommended timeframe to help reduce residue Suitable for most interior paint systems including acrylic and enamel Value 6 pack for multi room or multi day projects Ideal For Masking skirting boards, window frames, architraves, and cornices Two tone feature walls and colour blocking Furniture upcycling and detailed trim work Protecting hardware and fixtures during repainting Specifications Brand Paint Partner Product Thick Masking Tape for Crisp Paint Lines Width 24 mm Length per roll 27 m Pack size 6 rolls Adhesive type Pressure sensitive Surface types Painted drywall, timber trim, metal, glass, and sealed surfaces Use Interior masking and edge definition Removal window Remove within the recommended project timeframe for clean results Colour Neutral masking tape How to Use Prep the surface Ensure it is clean, dry, and free of dust or grease. Lightly sand and wipe where needed. Apply the tape Align to the paint edge and press down firmly, smoothing along the full length to seal the edge. Paint Apply paint in light coats, brushing or rolling away from the tape edge to reduce bleed. Remove While paint is still slightly tacky or once fully dry per paint instructions, peel the tape back on itself at a 45 degree angle. Pro Tips Burnish the tape edge with a clean cloth or plastic card for the sharpest lines. For textured walls, apply a very light coat of the base colour along the tape edge, let it set, then apply the top colour. Test in a small, hidden area on delicate or freshly painted surfaces. What’s in the Pack 6 rolls of Paint Partner Thick Masking Tape, each 24 mm x 27 m. Storage and Safety Store in a cool, dry place away from direct sunlight. Use on fully cured paint only. Always test before full application. Dispose of used tape in household waste according to local guidelines. Frequently Asked Questions Will it pull off existing paintWhen applied to properly cured paint and removed within the recommended timeframe, it is designed for clean removal. Always test on a small area first. Can I use it outdoorsBest suited for interior projects. For extended outdoor exposure consider a UV resistant painter’s tape. How do I get the sharpest edgePress the tape down firmly along the edge and remove at a 45 degree angle while paint is slightly tacky or fully cured as directed by the paint manufacturer. Why Buy From Glues Australia Australian based support and fast dispatch Carefully curated paint preparation range Competitive pricing on multi pack project essentials

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $9.65 $7.87

  View options

• 

  View options

  Timbermate Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler (No Waste, Easy Sand)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $10.50 - $175.00

  View options

• 

  View options

  Tricleanium Tricleanium Ultra Concentrated Cleaner Sugar Soap 400g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $9.70

  View options

• 

  View options

  Tricleanium Tricleanium Ultra Concentrated Cleaner Sugar Soap 2Kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $28.21

  View options

• 

  View options

  Sika SikaBond TechGrip High Strenght Multipurpose Polyurethane Adhesive Bottle 500g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SikaBond®  -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond®  -TechGrip can be used on most substrates due to its excellent adhesion. These include:  Wood  Stone  Metals  Glass  Ceramics  Concrete  Brick  Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond®  -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.  A full Material Safety Data sheet is available from Sika on request. 

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $24.20

  View options

• 

  View options

  Selleys Selleys All Clear Crystal Multipurpose Sealant for Wet, Oily & Dirty Surfaces Paint, Mould & Water Resistant

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $17.30

  View options

• 

  View options

  Rite RiteTack InvisiFix Crystal Clear Adhesive 290ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $9.95

  View options

• 

  View options

  PC Products PC Fahrenheit Epoxy Putty 8 Minutes High Temperature Waterproof 28.5g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. -  Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $16.17

  View options

• 

  View options

  Parfix Parfix PVA 1L Wood Glue High Strength for Woodworking Dries Clear

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $19.67

  View options

• 

  View options

  Parfix Parfix All Purpose Highly Flexible Silicone Sealant Clear 300g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters. Highly flexible Mould and UV resistant Neutral cure Non-corrosive

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $10.20

  View options

• 

  View options

  Nordsjo Nordsjo Professional Super Filler - Exterior 500ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result.   Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces   Tools Needed: Filling Knife   Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey   How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.66

  View options

• 

  View options

  Monarch Monarch Mini Skeleton Caulking Gun

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  The Monarch Mini Skeleton caulking gun is a smaller size caulking gun matched to the range of Monarch Mini sealant cartridges. This compact design provides easier access to tight spaces where conventional size guns find difficult. Featuring an inbuilt cartridge opener, the mini caulking gun can open a cartridge safely without using a knife for quick & easy use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $7.20

  View options

• 

  View options

  Gorilla Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Black]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $27.91

  View options

• 

  View options

  Selleys Araldite Super Strenght Expoxy Adhesive Maximum Bond 35ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $29.36

  View options

• Sale -23%

  View options

  Foilboard Foilboard Silver Insulation Tape for Joining Panels 48mm x 50m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Seal, reinforce, and finish Foilboard panel joins with this bright silver insulation tape. It creates a clean, professional finish while helping maintain a continuous moisture and air barrier across your installation. Key Features Strong adhesive for secure bonds on Foilboard and reflective insulation surfaces Aluminium foil backing for a neat, reflective finish Helps maintain vapor barrier continuity at seams and penetrations Conformable backing that sits flat on corners and edges Low residue when removed from clean, sound surfaces Suitable for indoor and sheltered outdoor applications Best For Joining Foilboard insulation panel seams Sealing butt joints, corners, and cut edges Patching minor nicks in foil facing General purpose foil tape tasks around HVAC plenums and reflective barriers How To Use Ensure surfaces are clean, dry, and free from dust or release agents. Position panels with tight, aligned seams. Apply tape centered over the joint with at least 12 mm coverage on each side. Press down firmly with a squeegee or cloth to remove air and ensure full contact. Overlap tape ends by at least 25 mm for continuous sealing. Specifications Backing Aluminium foil, silver finish Adhesive High tack pressure sensitive Width 48 mm Length 50 m Application Temperature Apply to clean, dry surfaces above 10°C for best results Colour Silver Tips For Best Results Wipe seams with a clean cloth to remove dust before taping. Use firm pressure along the full tape width to activate the adhesive. Store the roll in a cool, dry place and keep the edge protected from debris. Frequently Asked Questions Can I use this on non foil surfacesIt bonds best to foil faced insulation, reflective barriers, and other clean, non porous surfaces. For porous substrates, prime or seal first. Is it suitable outdoorsSuitable for indoor and sheltered outdoor areas. For direct weather or UV exposure choose a tape designed for full exterior exposure.  

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.79 $17.55

  View options

• Sale -24%

  View options

  Gorilla Gorilla Black Mounting Tape Strong 60lbs Indoor Hold 3.04m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Gorilla Black Mounting Tape delivers a fast, permanent bond for indoor projects. This industrial strength double sided tape grips to a wide range of smooth and lightly textured surfaces, helping you mount, fix, and build without screws or nails. Why you will love it Strong indoor hold with permanent bond Double sided for clean, hidden mounting Works on smooth and lightly textured surfaces Easy, tool free application Weather resistant carrier helps resist moisture and temperature changes indoors Great for Mounting hooks, signs, cable clips, and décor Fixing skirting trims and craft fixtures Securing powerboards and small organisers to walls or furniture DIY quick fixes where drilling is not an option Works on Metal, glass, finished wood, plastic, tiles, painted drywall, stone, and more. Not recommended on delicate, recently painted, dusty, oily, or damp surfaces. How to use Clean surfaces with isopropyl alcohol and let dry. Measure and cut the length you need. Press tape firmly onto the back of the object. Peel liner to expose the adhesive. Position once and press firmly for 30 to 60 seconds to activate the bond. Load gradually. Full bond strength develops after proper pressure and dwell time. Pro tips Use enough tape to support the weight of the item. As a guide, allow generous coverage across the mounting area. For painted surfaces, test in a small area first. Removal may damage paint. Avoid repositioning after contact. This reduces bond strength. Specifications Brand Gorilla Product type Double sided mounting tape Colour Black Length 3.04 m Use Indoor Bond Permanent Care and safety Keep out of reach of children. Do not use as a load bearing safety device. Store in a cool, dry place with liner intact.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $36.07 $27.45

  View options

• 

  View options

  Selleys Selleys Liquid Nails Construction Adhesive 320g (3 Pack)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $19.50

  View options

Show more products

Trade-grade adhesives, sealants and repair systems designed for durability, productivity and compliance on site. Expect higher strength, specific temperature/chemical resistance and precise application methods (e.g., static-mix nozzles, trowel spreads). Verify standards/approvals where required and follow measured mix ratios, bead sizes and cure schedules. Use filters to refine by chemistry, pot life and service rating. Always consult the product page and TDS/SDS, and observe PPE/safety practices.