Professional Use

Show previous products

• 

  View options

  Selleys Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $18.00

  View options

• 

  View options

  Loxeal Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts, bolts and studs of all types that may need to be dismantled later with standard hand tools. It tolerates minor oil contamination on the parts, so it keeps performing where threads are not perfectly clean. Once cured it resists vibration, corrosion, water, gas, oils, hydrocarbons and many other chemicals, and it holds its sealing properties from -55°C to +200°C (up to +250°C for short periods), with proven unscrewing resistance at +200°C. Why choose Loxeal 55-03? Medium strength – assemblies can be dismantled with normal tools when servicing is needed Tolerates light oil contamination on threads Locks and seals fasteners in one step, stopping loosening caused by vibration Wide service temperature range of -55°C to +200°C Blue colour, fluorescent under blue light, for easy inspection on the production line Seals the thread against ingress, helping prevent rust and fretting corrosion Certified and approved Approved as a gas-tight sealant for threaded fittings to European norm EN 751-1 (DVGW and Gaz de France) WRAS approved – suitable for use in contact with potable water Compliant with the UBA (German Environment Agency) declaration for potable water applications NSF registered in category S4 as acceptable for use as an adhesive in and around food processing areas Typical applications Securing nuts, bolts, studs and screws on machinery, vehicles and equipment subject to vibration Sealing threaded fittings on gas, water and compressed air lines Automotive, plumbing and general maintenance work where later disassembly must remain possible How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before putting the joint into service. On passive surfaces (e.g. stainless steel, plated parts) or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure (this may slightly reduce final strength). Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Viscosity (+25°C) 1,700–9,000 mPa·s, thixotropic Specific gravity (+25°C) 1.07 Max thread size / gap fill M36 / 0.25 mm Shear strength (ISO 10123) 9–13 N/mm² Breakaway torque (ISO 10964) 18–23 N·m Prevailing torque (ISO 10964) 9–16 N·m Service temperature -55°C to +200°C (+250°C short term) Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel, with good resistance to petrol, brake fluid, 50% water/glycol and acetone after 1,000 hours of exposure. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. Not approved for use with pure oxygen or oxygen-rich systems, and not suitable for sealing chlorine or other strong oxidising agents. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $29.95

  View options

• Sale -21%

  View options

  Gorilla Gorilla Black Mounting Tape Strong 60lbs Indoor Hold 3.04m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Gorilla Black Mounting Tape delivers a fast, permanent bond for indoor projects. This industrial strength double sided tape grips to a wide range of smooth and lightly textured surfaces, helping you mount, fix, and build without screws or nails. Why you will love it Strong indoor hold with permanent bond Double sided for clean, hidden mounting Works on smooth and lightly textured surfaces Easy, tool free application Weather resistant carrier helps resist moisture and temperature changes indoors Great for Mounting hooks, signs, cable clips, and décor Fixing skirting trims and craft fixtures Securing powerboards and small organisers to walls or furniture DIY quick fixes where drilling is not an option Works on Metal, glass, finished wood, plastic, tiles, painted drywall, stone, and more. Not recommended on delicate, recently painted, dusty, oily, or damp surfaces. How to use Clean surfaces with isopropyl alcohol and let dry. Measure and cut the length you need. Press tape firmly onto the back of the object. Peel liner to expose the adhesive. Position once and press firmly for 30 to 60 seconds to activate the bond. Load gradually. Full bond strength develops after proper pressure and dwell time. Pro tips Use enough tape to support the weight of the item. As a guide, allow generous coverage across the mounting area. For painted surfaces, test in a small area first. Removal may damage paint. Avoid repositioning after contact. This reduces bond strength. Specifications Brand Gorilla Product type Double sided mounting tape Colour Black Length 3.04 m Use Indoor Bond Permanent Care and safety Keep out of reach of children. Do not use as a load bearing safety device. Store in a cool, dry place with liner intact.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $36.07 $28.44

  View options

• Sale -19%

  View options

  Grunt Grunt Flashing Tape for Roofs and Gutters 50mm x 10m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Seal leaks fast and protect exposed joins with Grunt Flashing Tape. This heavy duty self adhesive tape conforms to uneven surfaces, creates a long lasting waterproof barrier, and is ideal for quick fixes and preventative maintenance across roofs, gutters, and outdoor fixtures. Why choose this tape Weatherproof seal that helps stop water ingress at laps, seams, and penetrations. Strong tack for reliable adhesion on metal, plastic, and painted surfaces. Flexible backing that moulds to contours, ridges, and fasteners. UV and outdoor ready for Australian conditions. Clean finish suitable for temporary and permanent repairs. Common uses Sealing gutter joins, end caps, and mitres Flashing around skylights, flues, and vents Stopping drips at roof sheet overlaps Repairing small cracks in downpipes and rainwater fittings Protecting fasteners and exposed fixings from water General waterproofing on caravans, sheds, pergolas, and trailers Surface compatibility Works on most clean, dry, and sound substrates including coated metal roofing, painted timber, rigid plastics, fibreglass, and masonry that has been sealed. Not recommended for silicone contaminated surfaces or areas that remain permanently submerged. How to apply Prepare the area. Remove dust, old flaking coatings, oil, and loose rust. Dry the surface thoroughly. Measure and cut the tape to length with a knife or scissors. Peel and stick. Remove the release liner as you apply, pressing the tape down firmly. Roll with a hand roller or the back of a cloth to eliminate air pockets and ensure full contact. Overlap adjoining pieces by at least 25 mm for a continuous seal. Finish edges with extra pressure. Avoid applying in rain or onto wet surfaces. Pro tips For porous substrates, prime with a suitable primer and allow to dry before taping. Cold weather can reduce tack. Warm the tape and surface slightly to improve bond. Ensure water can shed over the tape rather than against the lap direction. Specifications Brand Grunt Product type Self adhesive flashing and sealing tape Size 50 mm width x 10 m length Use Exterior and interior repairs, roofs, gutters, and general waterproofing Application temperature Apply in dry conditions on clean and sound surfaces Cleanup Wipe tools with mineral turpentine or adhesive remover as suitable for the substrate Frequently asked questions Can I paint over itYes, most solvent based and acrylic paints will adhere. Test a small area first. Is it suitable for potable waterNot intended for potable water contact. Will it work on damp surfacesBest results are achieved on dry surfaces. Dry the area before application.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $15.20 $12.25

  View options

• Sale -18%

  View options

  Paint Parner Paint Partner Thick Masking Tape for Crisp Paint Lines 24mm x 27m - 6 Pack

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Get sharp, clean paint edges with Paint Partner Thick Masking Tape. This reliable painter’s tape is designed to stick firmly, remove cleanly within the recommended time, and resist paint bleed for professional looking results on walls, ceilings, trims, doors, and furniture. Crisp paint lines with reduced bleed on properly prepared surfaces Thicker construction for easy handling, straight tearing, and consistent edging Clean removal within the recommended timeframe to help reduce residue Suitable for most interior paint systems including acrylic and enamel Value 6 pack for multi room or multi day projects Ideal For Masking skirting boards, window frames, architraves, and cornices Two tone feature walls and colour blocking Furniture upcycling and detailed trim work Protecting hardware and fixtures during repainting Specifications Brand Paint Partner Product Thick Masking Tape for Crisp Paint Lines Width 24 mm Length per roll 27 m Pack size 6 rolls Adhesive type Pressure sensitive Surface types Painted drywall, timber trim, metal, glass, and sealed surfaces Use Interior masking and edge definition Removal window Remove within the recommended project timeframe for clean results Colour Neutral masking tape How to Use Prep the surface Ensure it is clean, dry, and free of dust or grease. Lightly sand and wipe where needed. Apply the tape Align to the paint edge and press down firmly, smoothing along the full length to seal the edge. Paint Apply paint in light coats, brushing or rolling away from the tape edge to reduce bleed. Remove While paint is still slightly tacky or once fully dry per paint instructions, peel the tape back on itself at a 45 degree angle. Pro Tips Burnish the tape edge with a clean cloth or plastic card for the sharpest lines. For textured walls, apply a very light coat of the base colour along the tape edge, let it set, then apply the top colour. Test in a small, hidden area on delicate or freshly painted surfaces. What’s in the Pack 6 rolls of Paint Partner Thick Masking Tape, each 24 mm x 27 m. Storage and Safety Store in a cool, dry place away from direct sunlight. Use on fully cured paint only. Always test before full application. Dispose of used tape in household waste according to local guidelines. Frequently Asked Questions Will it pull off existing paintWhen applied to properly cured paint and removed within the recommended timeframe, it is designed for clean removal. Always test on a small area first. Can I use it outdoorsBest suited for interior projects. For extended outdoor exposure consider a UV resistant painter’s tape. How do I get the sharpest edgePress the tape down firmly along the edge and remove at a 45 degree angle while paint is slightly tacky or fully cured as directed by the paint manufacturer. Why Buy From Glues Australia Australian based support and fast dispatch Carefully curated paint preparation range Competitive pricing on multi pack project essentials

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $9.65 $7.87

  View options

• 

  View options

  Crommelin Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $16.45

  View options

• 

  View options

  RLA RLA Polymers Aftek MDF Adhesive 250ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Aftek MDF Adhesive 250 ml Overview Aftek MDF Adhesive 250 ml is a high quality fast setting MDF adhesive set designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials MDF timber trims decorative profiles Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Use in ventilated areas between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Activator accelerates set in seconds to minutes. Full strength develops over several hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Remove overspray and uncured adhesive with suitable solvent. Use carefully to avoid staining. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $12.53

  View options

• 

  View options

  Dunlop Dunlop Multipurpose Carpet & Cork Adhesive 1L

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  High strength, water based adhesive for carpet and cork Dunlop Multipurpose Carpet & Cork Adhesive is a water based, high strength adhesive designed for installing smooth or textured backed carpets and cork tiles. It delivers excellent wet grab and reliable bond on prepared subfloors. Suitable Surfaces Concrete Marine plywood Fibre cement sheet Key Features Water based and low odour High initial grab for reduced slippage Repositioning window up to 60 minutes Install immediately into wet adhesive for most carpets For cork or stiff backings, allow 10 to 15 minutes tack time before laying Coverage Approx. 2.5 m² per litre with a 3.2 mm V notch trowel Approx. 3.5 m² per litre with a 2.4 mm V notch trowel Application Ensure subfloor is dry, smooth, clean and protected from moisture. Prime highly porous concrete or timber before applying. Spread an even coat with the recommended V notch trowel. Lay carpet into the wet film. For cork or stiff backings, wait until the adhesive becomes tacky. Roll in both directions with a suitable drum roller to ensure full transfer. Set and Traffic Times No foot traffic for 24 hours Heavy traffic after 48 hours Avoid water and cleaning for 48 hours Clean Up Clean tools immediately with warm soapy water Remove dried residue with mineral turps Storage Shelf life up to 12 months in an unopened container stored at around 23°C. Good To Know Apply between 10°C and 30°C. Coverage varies with subfloor condition and trowel technique.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $54.95

  View options

• 

  View options

  Selleys Selleys Araldite Extra Time Epoxy Adhesive 200ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $79.51

  View options

• 

  View options

  Timbermate Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler (No Waste, Easy Sand)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $10.92 - $175.00

  View options

• 

  View options

  Uni-Pro Uni-Pro Carbon Steel Flexible Scraper Wooden Handle 50mm

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $5.64

  View options

• 

  View options

  Sika SikaBond TechGrip High Strenght Multipurpose Polyurethane Adhesive Bottle 500g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SikaBond®  -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond®  -TechGrip can be used on most substrates due to its excellent adhesion. These include:  Wood  Stone  Metals  Glass  Ceramics  Concrete  Brick  Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond®  -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.  A full Material Safety Data sheet is available from Sika on request. 

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $24.20

  View options

• 

  View options

  Sika Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SIKASIL® -670 FIRE | JOINT SEALANT Fire-rated joint sealant Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Easy to smooth and very good workability DESCRIPTION Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant. USES Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. CHARACTERISTICS / ADVANTAGES ▪ Up to 4 hours fire resistance according to EN 1366-4 ▪ Very good resistance to weathering ▪ Movement capability of ± 35% (ASTM C 719) ▪ Easy to smooth and very good workability ▪ Good adhesion to many different substrates ▪ Neutral curing ENVIRONMENTAL INFORMATION ▪ LEED® EQc 4.1 ▪ SCAQMD, Rule 1168 ▪ BAAQMD, Reg. 8, Rule 51 APPROVALS / STANDARDS ▪ EN 15651-1 F EXT-INT CC 25 LM ▪ EN 15651-4 PW INT ▪ ISO 11600 F 25 LM & G 25 LM ▪ ASTM C 920, class 35 ▪ EN 1366-4 assessment report ▪ ETAG 026 assessment report ▪ EN 13501-2 classification report ▪ EN 140-3 ▪ EN 13501-1 class B-s2-d0 PRODUCT INFORMATION Chemical Base Neutral cure silicone Colour: Grey Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C. Density 1.35 kg/l approx. (ISO 1183-1) TECHNICAL INFORMATION Shore A Hardness 16 approx. (after 28 days) (ISO 868) Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339) 0.50 N/mm2 approx. at 100% elongation (−20 °C) Elongation at Break 650% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719) Service Temperature −40 °C to +150 °C Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below). Backing Material Use polyethylene foam backing rods. Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390) Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature Substrate Temperature +5 °C to +40 °C Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2) Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1) Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2) APPLICATION INSTRUCTIONS SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without primers and/or activators APPLICATION METHOD / TOOLS Sikasil®-670 Fire is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically. FURTHER DOCUMENTS ▪ Safety Data Sheet (SDS) ▪ EN 13501-2 classification report ▪ ETAG 026 assessment report ▪ Brochure Sika Fire Protection Solutions LIMITATIONS ▪ Sikasil®-670 Fire cannot be overpainted. Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product. ▪ Do not use Sikasil®-670 Fire on natural stone. Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant. ▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools. ▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion. ▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.  

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.15

  View options

• 

  View options

  Selleys Selleys Sugar Soap Cleaner Concentrate 1L Makes 80 litres

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $8.50

  View options

• 

  View options

  Selleys Selleys Liquid Nails Original Adhesive All Weather High Strength 320g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to respond to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces   How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. If there is old difficult to remove residue such as old flaky paint, we recommend using paint stripper such as SELLEYS KWIK STRIP SMART, and allow to dry. On wet timber pooled water should be wiped off. Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/ Course grain, as the construction adhesive will adhere more readily to a scratched up surface. Cut the seal at the top of the cartridge. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of work which requires a caulking gun. Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining. The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days. When the product is still wet it can be removed with mineral turpetine, otherwise if the product is dry it can be removed by sanding or scraping, we recommend using a 50mm ROTA COTA Soft Grip Scraper. Clean any excess from your hands with SELLEYS Hand Kleen Wipes. To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid nails into the groove or each board when installing. Handy tips When applying to one surface, ensure sufficient LIQUID NAILS Original is used so that some adhesive extrudes out when surfaces are brought together then wipe off excess if necessary. If glue is not visible, then insufficient contact may not have been made between the surfaces and a weak joint may result. LIQUID NAILS Original should always be used in conjunction with mechanical fasteners in structural, critical or high stress applications. LIQUID NAILS Original is sometimes called LIQUID NAILS (SOLVENT) to differentiate it from the other Liquid Nails products. LIQUID NAILS Original shrinks slightly on curing. Cured LIQUID NAILS Original residues can be removed by holding a rag soaked in Mineral Turps against the residue, then rubbing the residue once softened. Mineral Turps penetrates in this way at approximately 1 mm per hour. When Liquid Nails Original joints are directly exposed to the weather, it is recommended to seal around the edges with a silicone sealant to prevent water ponding inside the joint and thus weaken the joint. LIQUID NAILS Original is NOT recommended for use on mirrors or polystyrene. Use LIQUID NAILS MIRROR METAL GLASS for mirrors and LIQUID NAILS FAST for polystyrene. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $6.73

  View options

• 

  View options

  Rite RiteTack InvisiFix Crystal Clear Adhesive 290ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $9.95

  View options

• Last stock!

  View options

  PC Products PC-7 Epoxy Waterproof Heavy Duty 56g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  PC-7® is the original tough job epoxy! This paste epoxy was originally formulated more than 60 years ago for the maximum in bonding power. Professionals to the do-it-yourselfers select PC-7® because of its exceptional adhesion to metals, ceramics, masonry and many plastics. PC-7® is designed for permanent repairs. Where other adhesives fail…PC-7® won’t! Choose PC-7® if you want to: seal a crack in a wall, attach a hanger to a ceramic plaque, seal a leak in an oil pan, repair a granite monument, fix a leak in PVC pipe connection, create a multimedia sculpture, and thousands of other repairs. When mixed, part A (gray) and the hardener part B (black) react to form a bond of tremendous strength. The PC-7® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 60 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-7® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Thicker than peanut butter but not as thick as bubble gum. Here are just a few specific uses (there are hundreds of other uses): Bond metal electrical boxes to concrete wall. Fill cracks in basement walls. Rebuild vintage Bakelite steering wheels. Seal holes in oil and transmission pans or fuel tank. Bond and repair stainless steel. Attach transition strips on concrete floor. Attach firing strips to concrete wall. Bond to and rebuild hard rubber bumper. How to prepare a surface for bonding with PC-7 Epoxy Paste Remove contaminants such as dust, dirt, oil and grime with solvents such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be scuffed using sandpaper to increase adhesion. How to clean-up after PC-7 Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-7® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. How thick can I apply PC-7®? PC-7® can be applied in any thickness. It does not require drying or exposure to air. It will cure from the inside out. I made a repair with PC-7® but need to build the area up more. Can I apply more epoxy? PC-7® sticks to PC-7® Can I use PC-7® for a vertical repair? PC-7® can be applied vertically and overhead. Because of its high viscosity it will not drip or sag. How long does it take PC-7® to harden? Normally, at 70F, PC-7® will cure in 24 hours but full hardness can take up to 48 hours. Cooler conditions will extend the cure time. Working in a garage or outside in temperatures between 50F and 60F may double the length of time needed for full cure. Applying PC-7® to a cool surface such as an exterior facing wall will slow down the cure. Can I paint over PC-7® and if so how? PC-7® should be primed then painted. Use Zinser Bullseye® 1,2,3 Stain Sealing Primer or Kilz® Premium Stain Sealing Primer or INSL-X® Stix Bonding Primer. Priming/sealing is important to separate and protect the finish coat from the epoxy/amine surface. Can I use PC-7® on a finished surface? Smooth, glossy or shiny surfaces should be roughened or scuffed with sandpaper to provide maximum adhesion. Use 80 or 120 grit sandpaper. A roughened surface has much more surface area than a smooth surface. PC-7® is very thick. Can I smooth it out or thin it out? Use a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol or Lacquer thinner to smooth applied PC-7®. Be-cause PC-7® is very thick and gooey, it is necessary to apply alcohol or acetone to the tool or gloved fingertips in order to lubricate the surface and shape or feather the applied epoxy. Can I use more of one part of PC-7® in order to speed the curing? Adding additional hardener does not make PC-7® cure faster. It is best to mix PC-7® one part of A to one part of B. However, PC-7® is probably the only epoxy that does not require precisely a 1:1 mix ratio. Plus or minus 25% A or B does not affect the performance. Adding additional PC-7® (+50%) part B hardener (black) can improve the adhesion to difficult surfaces such as PVC pipe and fittings. Measure equal volumes of part A epoxy (gray) and part B hardener (black) then measure an additional half portion of hardener (black). This will make the mix ratio (1 : 1.5, A : B). Can I tint PC-7® to match a surrounding color? PC-7® can be tinted with iron oxide or carbon pigments. Powdered pigments are used to color stucco or concrete and can be found at art supply stores. Universal tints that are used to color paint are compatible with PC-7®. Too much tint may affect the performance of PC-7®. I want to do a repair outdoors and the epoxy seems really stiff? PC-7® becomes more viscous in cool temperatures. Set the containers in a warm place prior to mixing. Acetone has been used to reduce the viscosity of PC-7®. The addition of acetone will contribute to shrinking and slow down the cure rate. PC-7® performs best without the addition of solvents. What will PC-7® bond to? It is easier to say what PC-7® will NOT bond to: Wax paper, Teflon, Plexiglass, vinyl and some softer plastics. Test an area if in doubt and always rough up shiny, smooth surfaces with sandpaper.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $17.86

  View options

• 

  View options

  Parfix Parfix PVA 1L Wood Glue High Strength for Woodworking Dries Clear

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $19.67

  View options

• 

  View options

  Parfix Parfix All Purpose Highly Flexible Silicone Sealant Clear 300g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters. Highly flexible Mould and UV resistant Neutral cure Non-corrosive

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $10.20

  View options

• 

  View options

  Nordsjo Nordsjo Professional Super Filler - Exterior 500ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result.   Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces   Tools Needed: Filling Knife   Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey   How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.66

  View options

• 

  View options

  Monarch Monarch Mini Skeleton Caulking Gun

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  The Monarch Mini Skeleton caulking gun is a smaller size caulking gun matched to the range of Monarch Mini sealant cartridges. This compact design provides easier access to tight spaces where conventional size guns find difficult. Featuring an inbuilt cartridge opener, the mini caulking gun can open a cartridge safely without using a knife for quick & easy use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $7.20

  View options

• 

  View options

  Loctite Loctite 263 Threadlocker Super Stud Lock 10ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole.  For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours.  Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush.  For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $19.84

  View options

• 

  View options

  Loctite Loctite 243 Threadlocker Super Nut Lock Medium Strenght 10ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies. LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids. Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces). Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Permits disassembly with hand tools for servicing Technology: Acrylic Chemical Type: Dimethacrylate ester Appearance (uncured) Blue liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity Medium, thixotropic Cure Anaerobic Secondary Cure Activator Application Threadlocking Strength Medium LOCTITE®  243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE®  243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. Shake the product thoroughly before use 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 8. Assemble and tighten as required For Disassembly 1. Remove with standard hand tools 2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot 3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $18.78

  View options

• 

  View options

  Davco Davco Sanitized Tile & Grout Sealer - Solvent-Based, 500ml, Water Repellent

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $20.98

  View options

• 

  View options

  Selleys Araldite Super Strenght Expoxy Adhesive Maximum Bond 35ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $29.36

  View options

• 

  View options

  Selleys AllFix Big Jobs MultiGrip Sticks Anything Adhesive Multipurpose 250g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys All Fix Big Jobs is a convenient all-rounder adhesive that sticks just about anything to anything. It provides virtually instant grab on dry porous surfaces eliminating the need for nails and screws on many jobs. It is a heavy-duty adhesive that will bond a wide variety of materials, has low fumes, and conveniently cleans up with water.  Features Fast - virtually instant grab on dry porous surfaces eliminates the need for nails and screws on many jobs Fast grab minimises the need for clamping Strong - Heavy-duty adhesive that will bond a wide variety of materials Safe - Low odour, low fumes and non-flammable Dries white and is able to be painted over once dry Lots of working time - bonds can be repositioned within 5-10 minutes Easy to use Fills minor gaps in uneven surfaces (bridges gaps up to 9mm) Strong bond on porous surfaces after 24 hours, cures to maximum strength over a few days Where can this product be used? Re-adhering carpet House numbers to brickwork Wooden furniture repairs Repairing damaged plasterboard Building a dog house Skirting boards Attaching architraves Attaching wall panelling Attaching chair (dado) rails Attaching or building a shelf Use for larger interior projects What materials is this product suitable for? Plasterboard Cabinet Plaster coving Carpet Wood Particleboard Metals (other surface must be porous) Glass (other surface must be porous) Ceramics (other surface must be porous) Brick (other surface must be porous) Concrete Cork Polystyrene foam (other surface must be porous) UPVC (other surface must be porous) Many rigid plastics* (other surface must be porous) Loose wall tiles (in non-wet areas) How to Use Surfaces to be bonded must be dry, sound and free from grease/oil and dust. Work tube between fingers for several seconds to loosen contents. Cut the tip of the nozzle and squeeze to apply adhesive onto one surface. Immediately press parts firmly together. Bonds can be repositioned for up to 5 minutes. If adhesive surfaces form a skin no bond will form. The bond will usually have good strength after 24 hours and will continue to strengthen for a few days. Application Tips For long narrow attachments (e.g. skirting boards) apply one or two continuous beads. For larger flat areas use beads approximately 30cm apart. For small items (e.g. tiles) spots of adhesive may be used. Wipe away excess adhesive with a damp cloth. Dried adhesive is best removed by scraping. Limitations: Not suitable for permanently wet or damp areas. Not suitable for fixing mirrors. Use Selleys Liquid Nails Mirror Metal & Glass. *Not suitable for polyethylene and polypropylene. Use Selleys All Plastic Fix. Bonds are not water-resistant. Protect bonds from water penetration if used in exterior applications. Not resistant to strong acids and strong organic solvents. Do not apply below 10°C. When used near brass or copper, the immediate area of contact will discolour to a blue tone. Handy Tips At least one surface must be porous for effective bonding. If both surfaces are non-porous, drying time is greatly increased. Clamping may be necessary until adhesive dries. Wet, damp and cold weather will increase drying time Wipe away excess with a damp rag. Use temporary supports when bonding a heavy load - support until adhesive dries. Particularly on uneven or smooth or non-porous surfaces. Good for gap filling - i.e. sticking two rough surfaces together. All Fix Big Jobs may stain slightly and colour can be paler than the surrounding area, squeeze out should be wiped off if intending to stain. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping. 

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $34.32

  View options

• 

  View options

  Loxeal Loxeal Superlox Polyolefin Bonder 25ml Bi-Syringe (Single)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: clean and degrease the plastics first for a stronger bond (no primer required). Loxeal Superlox Polyolefin Bonder 25ml Bi-Syringe (Single) Loxeal Superlox is a two-part acrylic adhesive developed to bond polyolefins, polypropylene (PP), polyethylene (PE), HDPE and LDPE, and other notoriously difficult low-surface-energy plastics, without primers, flame treatment or other expensive surface pre-treatments. This listing is for a single 25ml bi-syringe supplied with a mixing nozzle, dispensing the two components at a simple 1:1 ratio, so you can buy just what one job needs. It joins polyolefins to each other and to other plastics such as ABS and PVC, and to metals, producing structural joints with high shear and peel strength. Why choose Loxeal Superlox? Bonds the "unbondable", PP, PE, HDPE and LDPE plus other low-surface-energy plastics No primer or surface pre-treatment required, clean, apply, assemble Single 25ml bi-syringe with mixing nozzle, fresh adhesive for the job at hand Simple 1:1 mixing ratio through the supplied static mixing nozzle Structural performance, high shear and peel strength on plastics and mixed-material joints Also bonds polyolefins to other plastics (ABS, PVC) and to metals Typical applications Repairing and fabricating PP and PE components: tanks, housings, containers, piping and trim Joining polyolefin parts to dissimilar plastics or metal brackets and fittings Manufacturing and maintenance work on low-surface-energy plastic assemblies How to use Clean the surfaces to remove dust, oil and grease (for example with Loxeal Cleaner 10) and allow to dry. Fit the static mixing nozzle to the bi-syringe and discard the first few centimetres of extruded adhesive. Apply the mixed adhesive to one surface. Assemble the parts promptly and hold or clamp them without movement while the adhesive sets. Leave the joint undisturbed until fully cured before applying load. Cure times Fast curing at room temperature, parts typically fixture within minutes of assembly Allow 24 hours for full strength before placing joints under working load Refer to the Technical Data Sheet for precise fixture and cure data for your conditions Specifications Chemistry Two-part structural acrylic, polyolefin bonder Mixing ratio 1:1 by volume via static mixing nozzle Key substrates PP, PE, HDPE, LDPE and other low-surface-energy plastics; also ABS, PVC and metals Surface preparation No primer or pre-treatment required, clean and dry surfaces only Strength profile High shear and peel strength Pack size 1 x 25ml bi-syringe with mixing nozzle Buying more than one? If you use Superlox regularly, the Superlox trade pack of 10 x 25ml bi-syringes works out cheaper per syringe. Important notes Work at room temperature; low temperatures slow the cure Use each mixing nozzle for one continuous application, fit a fresh nozzle if work is interrupted Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and avoid skin and eye contact. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $54.95

  View options

• 

  View options

  Loxeal Loxeal Activator 11 Anaerobic Accelerator Spray 200ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Speeds the cure of Loxeal anaerobic products, including: Threadlockers 55-03 and 83-54, thread sealants 55-14 and 85-86, retaining compounds 53-11 and 82-21, and gasketing 58-14, 58-31 and 59-10. Loxeal Activator 11 Anaerobic Accelerator Spray 200ml Loxeal Activator 11 cleans, degreases and dramatically accelerates the cure of anaerobic adhesives and sealants – threadlockers, threadsealants, retaining compounds and gasketing products. It is the answer when anaerobic products cure slowly or unreliably: on passive surfaces (such as stainless steel, plated finishes and many alloys), at low temperatures, or across larger gaps. Spray one surface, let the solvent flash off for a few seconds, and fixture is typically achieved in 20–120 seconds. Supplied as a 200ml aerosol for fast, even coverage. Why choose Loxeal Activator 11? Speeds anaerobic fixture time to 20–120 seconds depending on adhesive, gap and temperature Cleans and degreases the joint in the same step Reliable curing in tough conditions – passive metals, cold workshops, larger gaps Long-lasting activation – treated parts remain active for up to three months when protected from dust and weathering Suitable for both threaded and flange joints Convenient 200ml aerosol spray application Typical applications Pre-treating stainless steel, zinc-plated and other passive fasteners before threadlocking or threadsealing Accelerating retaining compounds on bearings, bushes and cylindrical assemblies Speeding gasket and flange sealant cure in cold conditions or production settings How to use Spray Activator 11 onto one of the surfaces to be joined. Allow the solvent to evaporate for a few seconds until the surface is dry. Apply the anaerobic adhesive or sealant to the other surface. Assemble the parts; fixture typically occurs within 20–120 seconds. Specifications Composition Organic activating agents in solvent carrier Appearance Green liquid Viscosity (+25°C) 1–2 mPa·s Specific weight (+25°C) 0.8 g/ml Flash point (COC/DIN/ISO 2592) +21°C Cure acceleration Fixture in 20–120 seconds (adhesive, gap and temperature dependent) On-part activation life 24 hours; up to 3 months if parts are protected from dust and atmospheric agents Breakaway torque (ISO 10964, ref. 83-54) >5 Nm after 5 minutes Pack size 200ml aerosol spray Shelf life 1 year unopened at +25°C Important notes Use of an activator may reduce the final mechanical strength of the anaerobic bond Wait for the solvent to fully evaporate before assembling parts Flammable – keep away from ignition sources and use with good ventilation Store in a cool, dry place at no more than +25°C; do not refill containers with used product Safety Consult the Safety Data Sheet (SDS) before use. Flammable aerosol: keep away from heat, sparks and open flames, use in a well-ventilated area and avoid inhaling vapours. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $54.95

  View options

• 

  View options

  Loxeal Loxeal Cleaner 10 Degreaser Spray 400ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  The recommended surface prep for Loxeal adhesives and sealants: Use before threadlockers, retaining compounds, gasketing, epoxies, structural acrylics and instant adhesives for maximum bond strength. Often paired with Activator 11 for anaerobics or Activator 9 for super glues. Loxeal Cleaner 10 Degreaser Spray 400ml Loxeal Cleaner 10 is a non-CFC, solvent-based cleaner and degreaser for preparing surfaces before bonding or sealing with adhesives and sealants. This 400ml aerosol puts fast, controlled surface prep straight in your hand: spray, wipe, and the solvent flashes off in around 60 seconds leaving a clean, dry, non-corroded surface ready for adhesive. Cleaner 10 has no effect on the cure speed or final strength of Loxeal adhesives and sealants – but a dirty joint certainly will. Why choose Loxeal Cleaner 10 spray? Convenient aerosol application – even coverage on parts, threads and hard-to-reach areas Fast flash-off – dries in about 60 seconds at room temperature Non-corrosive and residue-free on metals Does not interfere with adhesive cure speed or bond strength Ideal partner for threadlockers, retainers, epoxies, structural acrylics and instant adhesives Non-CFC solvent formulation Typical applications Spray-degreasing fasteners, threads and machined parts before threadlocking or retaining Cleaning oil- and grease-contaminated surfaces in maintenance and assembly work Preparing treated, coated or plastic substrates prior to bonding (check compatibility first) How to use Spray Cleaner 10 directly onto the surfaces to be bonded. While still wet, wipe with a clean cloth to remove heavy contamination. Allow the solvent to evaporate until the surface is completely dry (about 60 seconds). Apply the adhesive or sealant immediately after drying and assemble the joint. Specifications Formulation Non-CFC solvent blend Appearance Colourless liquid Boiling range +92°C to +102°C Flash point (COC/DIN/ISO 2592) -1°C (highly flammable) Density (+25°C, DIN 51757) 0.70 g/ml Drying time (+25°C) Approx. 60 seconds Water solubility Not soluble Corrosivity None Pack size 400ml aerosol spray Shelf life 12 months at +5°C to +25°C Important notes The solvent can affect certain plastics and coatings – check compatibility on a hidden area first Unclean or partially cleaned surfaces can significantly reduce adhesive performance Pressurised container – protect from sunlight and do not expose to temperatures above +50°C Store between +5°C and +25°C in a cool, dry place Safety Consult the Safety Data Sheet (SDS) before use. Highly flammable aerosol: keep away from naked flames, sparks and non-flameproof electrical equipment, use only in well-ventilated areas, avoid prolonged skin contact and do not smoke near the product. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $46.95

  View options

• Sale -7%

  View options

  Glitz Glitz Calcium Scale and Rust Remover Bathroom Deep Clean 2L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Cut through stubborn limescale, soap scum, and rust stains with Glitz Calcium Scale and Rust Remover. This powerful bathroom cleaner is formulated to lift mineral build up fast so sinks, taps, tiles, glass, and shower screens look clean and fresh again. The generous 2L size is ideal for whole home maintenance or trade use. Why you will love it Targets tough mineral deposits like calcium, lime, and rust Breaks down soap scum for a brighter, streak free finish Works on ceramic, porcelain, glass, chrome, stainless steel, and most bathroom surfaces Fast acting formula helps reduce scrubbing time 2L value size for households, cleaners, and facilities teams Best for Shower screens and doors Wall tiles and grout surrounds Basins, baths, and toilets on the exterior porcelain Taps, shower heads, and chrome fittings Not recommended for Avoid natural stone like marble, limestone, travertine, or terrazzo. Avoid enamel cookware, unsealed or damaged surfaces, and any surface that states not to use acidic cleaners. If unsure, test on a small hidden area first. How to use Preparation Remove loose debris and pre rinse the surface with warm water. Light scale and soap scum Dilute 1 part product to 4 parts water. Apply with a sponge or spray bottle. Heavy scale and rust stains Use undiluted. Apply directly to the stain and let it sit for 2 to 5 minutes. Do not allow to dry on the surface. Agitate Wipe or scrub with a non scratch pad or soft brush. Rinse well Flush thoroughly with clean water until the surface is neutral and residue free. Repeat if needed For very stubborn deposits, repeat the process in short contact times. Pro tips For shower heads with internal scale, remove the head and soak in a diluted solution. Rinse well before refitting. Squeegee shower glass after each use to slow future build up. Always spot test first. Some finishes are more delicate than others. Safety and handling Wear gloves and eye protection during use Use in a well ventilated area and avoid inhaling mist Do not mix with bleach or ammonia Keep out of reach of children and pets Store upright in a cool, dry place with cap closed After care Once deposits are removed, maintain surfaces with a neutral pH daily cleaner. Regular rinsing and drying will help prevent new mineral build up. Product details Brand Glitz Product Calcium Scale and Rust Remover Bathroom Deep Clean Size 2L Form Liquid Suitable surfaces Ceramic, porcelain, glass, chrome, stainless steel, most glazed tiles Do not use on Natural stone, terrazzo, unsealed or damaged surfaces, acid sensitive finishes Cleanup Rinse with plenty of clean water What is in the box 1 x Glitz Calcium Scale and Rust Remover 2L Good to know Contact time should be short. Rinse thoroughly to protect finishes. For vertical surfaces, apply with a sponge to reduce run off. For regular maintenance, switch to a gentle daily cleaner between deep cleans.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $23.66 $22.00

  View options

• Sale -25%

  View options

  Gorilla Gorilla Double Sided Tape Mount and Bond Instantly 7.3m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Get a fast, permanent hold without screws, nails, or messy liquid glues. Gorilla Double Sided Tape delivers an instant tack and a strong bond on smooth and slightly rough surfaces so you can mount, fix, and create with confidence. Why you will love it Instant grab for quick, clean mounting jobs Heavy duty hold with a long lasting bond No tools needed just press to stick Works indoors and outdoors in normal Australian conditions Cleaner finish compared to visible fasteners Great for Fixing signs, hooks, cable clips, and small fixtures Mounting lightweight décor, trims, and name plates DIY repairs around the home, office, classroom, and workshop Craft projects and display boards Suitable surfaces Painted walls*, metal, sealed wood, glass, tiles, plastics, and smooth masonry. *Always test first on painted or delicate surfaces. Fresh paint must cure fully. How to use Clean both surfaces. Remove dust, oil, and moisture for best adhesion. Cut to length. Use sharp scissors or a utility knife. Apply tape to the first surface and press firmly along the full length. Peel the liner to expose the second side. Mate surfaces and press hard for 30 to 60 seconds to set the bond. Full strength develops after proper pressure. Avoid load for a short period where possible. Removal tip: lift slowly from one corner. On delicate finishes, use a plastic scraper and take care. Product details Brand Gorilla Type Double sided mounting tape Length 7.3 m Adhesive Permanent pressure sensitive Use Interior and exterior in typical household conditions Solvent free Yes Pro tips for the best hold Adhesion improves with firm pressure. Roll or press along the tape after application. For porous or chalky surfaces, seal first for a stronger bond. Cut multiple shorter strips to cover more area on larger items. Avoid contact with dust or fingers once the liner is removed. FAQ Is it removableThe bond is permanent and removal can damage delicate finishes. Test first. Will it hold in damp areasIt bonds in normal household humidity. For constantly wet or submerged applications choose a waterproof sealant or specialty tape. Shipping and returns Fast dispatch Australia wide from Glues Australia Carefully packed to protect your order Change of mind returns available if unopened and in resalable condition Always follow the instructions on the retail pack. Performance varies with surface, preparation, and load. If in doubt, test before full application.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.87 $17.08

  View options

• 

  View options

  Selleys Selleys Liquid Nails Construction Adhesive 320g (3 Pack)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $19.50

  View options

• 

  View options

  Selleys Selleys Sealant & Adhesive Remover 375g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys Sealant & Adhesive Remover 375g helps soften and lift old sealants and sticky residues so you can cleanly remove them and re-seal with confidence. The non-drip formula clings to joints and vertical surfaces, making bathroom and kitchen refreshes faster and easier. Key benefits Softens cured silicone and many common sealants to aid scraping and removal Helps break down adhesive residue, tapes and grime build-up Non-drip gel action for vertical joints, corners and trims Low mess application with excellent wetting of tight gaps Preps surfaces for fresh re-sealing and re-bonding Where to use Bathrooms: around showers, baths, basins and splashbacks Kitchens and laundries: benchtop perimeters, sinks and tiles Windows and doors: frames, trims and glazing edges Suitable substrates Glass, ceramic tiles, porcelain, enamel, stainless steel and many metals Some plastics and laminates (always test first in an inconspicuous spot) Not recommended on Natural stone, marble or porous tiles Freshly painted, delicate or lacquered surfaces Acrylic and polycarbonate sheets, mirror backings and other sensitive plastics Directions Cut away and remove as much old sealant as possible with a plastic scraper. Protect surrounding areas. Shake or stir if required, then apply a generous layer to remaining residue. Allow time for the remover to penetrate. Dwell time will vary by sealant type and thickness. Gently scrape and wipe away loosened material. Reapply if needed for stubborn spots. Wash the area with warm soapy water, rinse and dry thoroughly before re-sealing. Pro tips Score thick beads along the edges with a utility blade before application to help penetration. Work in manageable sections and avoid letting the remover dry on the surface. Always test on a small hidden area to check surface compatibility. Safety Use in a well ventilated area and wear gloves and eye protection. Avoid contact with skin and eyes. Keep out of reach of children. Product details Brand: Selleys Type: Sealant and adhesive remover Pack size: 375g

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $38.69

  View options

• 

  View options

  Dunlop Dunlop Vinyl Adhesive 1L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $27.85

  View options

• 

  View options

  Tuff Turf Tuff Turf Synthetic Grass Adhesive 320g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Tuff Turf Synthetic Grass Adhesive 320 g Overview Tuff Turf Synthetic Grass Adhesive 320 g is a high quality synthetic grass adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials synthetic turf backing seaming tape concrete compacted base plywood Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Install in dry conditions between 10°C and 30°C, avoiding heavy dew or rain. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Working time varies with conditions. Allow sufficient cure before foot traffic. Full strength typically within 24 to 48 hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean tools while wet with a suitable solvent or soapy water depending on formulation. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $13.40

  View options

• 

  View options

  Sika Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $35.34 - $39.95

  View options

• 

  View options

  Weldbond Weldbond Steel Tough Welbond Universal Adhesive Tube 60ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $8.13

  View options

• 

  View options

  T-Rex T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects. Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions. T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger. Key Features: All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications. Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in. Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold. Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan. Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox. Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability. Usage Applications: Home repairs, including fixing broken items and sealing leaks. Crafting and DIY projects, offering creative flexibility. Outdoor applications, including camping gear repairs. Professional job site tasks, providing reliability and strength. Why Choose T-Rex® Tape? When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project. In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $16.48

  View options

• 

  View options

  Sika Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics.   Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.  

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $53.62

  View options

• 

  View options

  Sika Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikaflex-227 is a one-component poly­­urethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $31.92

  View options

• 

  View options

  Sika Sika Sikasil Pool Silicone Water Resistance [Transparent]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $20.82

  View options

• 

  View options

  Sika Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $5.82

  View options

• 

  View options

  Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $23.98

  View options

• 

  View options

  Sika Sika Sikaflex 291 Marine Adhesive Sealant [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikaflex®-291 Marine Adhesive Sealant  Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).  

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $28.97

  View options

• 

  View options

  Sika Sika Sikaflex 118 Extreme Grab 290ml [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use.   Very high initial grab Fixing of heavy objects without temporary fixation Good workability   Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors*   Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking   Packaging 290 ml cartridge, 12 cartridges per box   Colour White   Composition Silane terminated polymer   Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging.   Density ~1.40 kg/l   Technical Information Shore A hardness ~50 (after 28 d)   Tensile strength ~2.2 N/mm2   Tear propagation resistance ~10.0 N/mm   Service temperature −40 °C min. / +80 °C max.   SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive.   For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed:   Non-porous substrates   Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth.   Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours).   Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing.   PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing.   Porous substrates   Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush.   Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours).   For more detailed advice and instructions contact Sika Technical Services.   Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint.   CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically.   For cleaning skin use Sika® Hand Wipes.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $31.22

  View options

• 

  View options

  Sika Sika Fine Surface Filler Filler-101 Interior Grade 0-3mm 400ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max.  Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika®  Filler-101 can fill ~ 1 m2  per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika®  Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika®  Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika®  Filler-105. When dried finish the surface with Sika®  Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. 

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $21.47

  View options

• 

  View options

  Sika Sika Showerbond shower wall lining adhesive fast curing 300ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages  Fast curing.  Will not damage plastic shower liners.  Panels can be relocated for up to 30 minutes after positioning.  Excellent adhesion to most common building materials.  Easy to apply and clean up.  Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application  Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining.  Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive.  Brace the lining as required in the shower manufacturer's installation instructions.  Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $21.37

  View options

• 

  View options

  Selleys Selleys No More Gaps Exterior & Weatherboard 430g [White]

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Selleys No More Gaps Exterior & Weatherboard is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. Has good resistance to weathering Contains a titanium compound for superior UV resistance. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application).. Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack. Is formulated for long term resistance to cracking and crumbling. Is water based, so can be cleaned up with water. Will not stain building materials. Where can this product be used? Between exterior window and door frames Fascia boards and eaves Masonry Walls Tiling Timber & synthetic weatherboards Brickwork Fences Where shrinkage or movement has caused rigid fillers to crack Gaps with a maximum width of 25mm & depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Fibre cement sheeting, plasterboard Masonry Ceramic Tiles Glass Aluminium & other metals Many other building surfaces

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $17.87

  View options

Show more products

Trade-grade adhesives, sealants and repair systems designed for durability, productivity and compliance on site. Expect higher strength, specific temperature/chemical resistance and precise application methods (e.g., static-mix nozzles, trowel spreads). Verify standards/approvals where required and follow measured mix ratios, bead sizes and cure schedules. Use filters to refine by chemistry, pot life and service rating. Always consult the product page and TDS/SDS, and observe PPE/safety practices.