Polyfilla Rapid 30 340g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 340g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 340g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$36.88
Polyfilla Rapid 30 140g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 140g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 140g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$21.59
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$38.10
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick. Water, weather, UV, algae and mould resistant Can be tooled to a render texture or sanded to a smooth finish. For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 500g and 2.2kg Colour: Cement grey in colour but can be painted over with both oil and water based paints • Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap. • Rinse thoroughly and allow surface to dry. • Use flexible filling blade to press filler into hole, or trowel to spread a thin layer over surface, and tool to a feathered edge. • Allow to dry (2–3 hours in thin 2–3mm applications, depending on temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. • Protect from rain until dry. If required, paint with a quality exterior coating. • For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$22.91
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$46.15
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
$4.19
The Monarch Mini Skeleton caulking gun is a smaller size caulking gun matched to the range of Monarch Mini sealant cartridges. This compact design provides easier access to tight spaces where conventional size guns find it difficult. Featuring an inbuilt cartridge opener, the mini caulking gun can open a cartridge safely without using a knife for quick & easy use. FEATURES Small, lightweight design Inbuilt cartridge opener Dripless BENEFITS Lightweight Swivel head for easy storage Comfortable design
$8.95
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$18.73
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$48.79
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$77.97
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.80
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal Metalox Metal Repair Epoxy 25ml Bi-Syringe (Single) Loxeal Metalox is a solvent-free, fast-curing, metal-filled two-part epoxy engineered for repairing and bonding metal components. This listing is for a single 25ml bi-syringe supplied with a mixing nozzle, so you can buy exactly what one job needs without committing to a trade pack. Its thixotropic (non-sag) paste works as an adhesive filler, rebuilding metal castings, pipework and flanges, and once cured it can be machined, sanded and painted, typically within a few hours of application. Why choose Loxeal Metalox? Single 25ml bi-syringe with mixing nozzle, accurately proportioned 1:1 dispensing on every repair Fast cure, handling strength in around 15 minutes, sandable in about 5 hours at room temperature Strong on steel, lap shear strength of 21 N/mm² on grit-blasted mild steel Machinable, sandable and paintable after polymerisation, even for outdoor repairs Non-sag thixotropic paste stays put on vertical and overhead surfaces Excellent resistance to water and many chemical agents Heat cure option: 1 hour at +60°C speeds cure and boosts final strength Typical applications Repairing metal castings, pipework and flanges Automotive body repair and panel filling Bonding metal substrates, plus concrete, wood and other rigid materials Maintenance and plant repairs where downtime must be kept short How to use Scratch or abrade the surface, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the bi-syringe and discard the first 3 to 5 cm of extruded product. Apply the mixed adhesive directly to the repair area; work at temperatures above +15°C. Assemble or shape immediately and leave undisturbed until cured. Once cured (sandable after about 5 hours at +25°C), machine, sand or paint as required. Cure times Pot life: approximately 5 minutes at +25°C Handling strength: approximately 15 minutes Sandable: about 5 hours at +25°C (90% of final hardness) Accelerated cure: 1 hour at +60°C for full resistance sooner Specifications Chemistry Two-part epoxy (resin / amine hardener), metal-filled Colour Part A metallic grey / Part B black Mixing ratio 1:1 by volume Pot life (+25°C) Approx. 5 minutes Handling strength Approx. 15 minutes Lap shear strength (ISO 4587) 21 N/mm² (grit-blasted mild steel); 18 N/mm² (stainless steel) Compression strength (ASTM D695) 60 N/mm² Hardness (ISO 868) Shore D 65 Pack size 1 x 25ml bi-syringe with mixing nozzle Shelf life 24 months unopened at +5°C to +25°C Buying more than one? If you go through Metalox regularly, the Metalox trade pack of 10 x 25ml bi-syringes works out cheaper per syringe. Important notes Apply at temperatures above +15°C; higher temperatures and large mixed quantities reduce pot life Avoid mixing excess product, the curing reaction generates heat Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Wear suitable gloves, avoid skin and eye contact, and work in a well-ventilated area. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$39.95
Selleys FlexiSeal (ProSeries) is a high-strength, fast-curing polyurethane sealant and adhesive built for tough construction jobs. It seals and bonds expansion and construction joints in both vertical and horizontal applications, staying highly flexible once cured so it can absorb the natural movement of a building without cracking or pulling away. This 600ml grey sausage pack suits a standard sausage gun and is ideal for larger trade and DIY jobs. Key features High-strength, flexible grey polyurethane adhesive and sealant Handles up to ±25% joint movement Non-slumping, low-modulus formula Fast curing and weatherproof for indoor and outdoor use Paintable after cure with no primer needed on most surfaces Excellent adhesion to most common building materials Where to use it Bonds and seals most building materials including concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics. Suitable for indoor and outdoor sealing of expansion and construction joints, around window and door frames, and general weatherproofing. How to use Prepare joints so they are clean, dry and free from oil, dust and curing agents. Use a backing rod for deeper joints. Cut the nozzle, load the sausage into a suitable gun and extrude the sealant, ensuring full contact with both joint sides and avoiding air entrapment. Tool and smooth off with a spatula. Once fully cured, paint if required using water-based paint. For solvent-based paints, undercoat with a water-based primer first. Important notes Applies and cures best at moderate temperatures (around 20°C), especially in cold weather. Will not adhere to PE, PP or PTFE; test other plastics and rubber before use. Not recommended for continuous submersion or below-water-line use. Not ideal over old or incompatible sealants, which may affect cure. Specifications Brand Selleys Product FlexiSeal (ProSeries) Multipurpose Sealant & Adhesive Technology Polyurethane joint sealant Colour Grey Size 600ml sausage Joint movement Up to ±25% Finish Paintable after cure Use Indoor and outdoor Safety Use in a well-ventilated area and avoid prolonged skin contact; wear suitable gloves and eye protection. Uncured polyurethane sealant may cause skin and eye irritation and can sensitise some users, so wash off any residue promptly. Keep out of reach of children. Always read the label and refer to the manufacturer’s Safety Data Sheet before use.
$27.25
The Sika WT-215 is a high-quality trade cartridge gun designed for professionals caulking large volumes daily. Strong and robust, it is built to withstand everyday use.Features & Benefits Dispenses 300–310 ml cartridges Swivel frame for continuous beading High-end professional applicator Robust construction for increased reliability Specifications Type Cartridge caulking gun Model WT-215 Cartridge size 300–310 ml Frame Swivel Grade Trade / professional
$72.94
The Sika WT-250XL is a professional-quality sausage and cartridge application gun with top-quality construction and an easy trigger action, dispensing sealants and adhesives in both sausage and cartridge forms.Features & Benefits Dispenses both sausages and cartridges 600 ml sausage capacity Easy trigger action with 12:1 pressure ratio Spare parts available Specifications Type Sausage / cartridge caulking gun Model WT-250XL Sausage capacity 600 ml Pressure ratio 12:1 Grade Professional
$111.98
Dunlop Wide Joint Grout is a cement-based tile grout purpose-made for the big joints that standard grouts can't handle, filling gaps from 5mm right up to 50mm wide. In a practical Mid Grey colour, it suits rustic and heavy-duty tiling styles where wide grout lines are part of the look, curing to a hard-wearing finish indoors and out.Where to use itUse it on walls and floors, indoors and outdoors, over ceramic tiles, terrazzo, quarry tiles and sealed terracotta and slate. It is the go-to grout for terracotta paving, quarry tile floors, feature walls and any tiled area with generous joint widths.How to useMix the powder with clean water to a firm, workable consistency and work it into the joints with a grout float, compacting well so the full joint depth is filled. Strike off excess on the diagonal, then clean the tile faces with a damp sponge once the grout has firmed. Porous tiles such as terracotta and slate should be sealed before grouting to prevent staining.Important notesDesigned for joints 5-50mm wide; for narrower joints use Dunlop Flexible Coloured Grout. Coverage varies with tile size and joint dimensions. Protect fresh grout from rain and frost while curing.Specifications Size 15kg bag Colour Mid Grey Joint width 5-50mm Tile types Ceramic, terrazzo, terracotta, slate, quarry tiles Coverage Approx. 9m² (200x200x10mm tiles, 8mm joint) to 11m² (600x600x10mm, 20mm joint) per 15kg Location Indoor and outdoor, walls and floors SafetyCement-based powder - alkaline when wet. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the work area ventilated, avoid prolonged skin contact and wash hands after use. Keep out of reach of children.
$41.19
The Hotwire Floor Heating Mat delivers all the comfort of Hotwire under tile heating with the heating cable already pre-spaced on a self-adhesive fibreglass mesh. Instead of fixing a loose cable, you simply roll the mat out across the floor — installation is fast, spacing is guaranteed even, and the finished system is invisible, silent, dust-free and energy efficient. At just 3.6 mm thick, the mat adds almost no height to the floor build-up, and the single cold tail keeps wiring simple. Every mat is supplied as a complete system with a fully programmable touch screen thermostat, floor temperature probe, installation alarm, tape and manual; WiFi and dual thermostats are available as upgrades.Where to use itPerfect for bathrooms, ensuites, laundries, kitchens and living areas under tile or stone. The ultra-thin profile makes it equally suited to new builds and retrofits in existing homes where floor height is limited, and the gentle radiant heat also dries wet-area floors, helping keep mould at bay.How to useMeasure the free floor area, roll the mat out and press the adhesive mesh onto a clean, primed subfloor, cutting the mesh (never the cable) to turn at walls. Fit the floor probe, then tile directly over the mat. All wiring, thermostat connection and testing must be completed by a licensed electrician, with resistance readings recorded before, during and after tiling.Important notesSize the mat to the open floor area only, excluding vanities, baths and fixed cabinetry. The heating cable must not be cut or shortened. Register your warranty after installation; the heating element is covered by a lifetime warranty (conditions apply).Specifications Wattage Coverage 300 W 2 m² 450 W 3 m² 600 W 4 m² 900 W 6 m² 1200 W 8 m² 1500 W 10 m² SafetyIndoor use only. This mat connects to 230–240 V mains and must be installed and wired by a licensed electrician to AS/NZS wiring rules on an RCD-protected circuit. Hotwire systems are independently tested to AS/NZS standards.
$873.06 - $1,723.38
The Hotwire Under Tile Heating Kit is a complete electric floor heating system built for Australian homes. A slim 4 mm heating cable is laid directly over the subfloor before tiling, so the warmth sits just below the floor surface and the room heats up in around 30–60 minutes. Each kit ships with everything needed for a professional result: the heating element, a fully programmable touch screen thermostat with floor temperature probe, installation alarm, fixing tape and manual. Running costs can be as low as a couple of cents per square metre per hour, and a WiFi thermostat upgrade is available.Where to use itIdeal for bathrooms, ensuites, laundries, kitchens and living areas — anywhere tiled floors feel cold underfoot. Because the heating warms and dries wet-area floors, it also helps reduce mould and cleaning. It suits renovations particularly well, since only the floor covering needs to be replaced to install it, and systems scale from a compact 1 m² zone up to large open-plan spaces.How to usePlan the heated area, fix the cable evenly across the subfloor at the spacing shown in the manual, position the floor probe, then tile or screed over the element. All electrical connections and the final wiring of the thermostat must be carried out by a licensed electrician, and continuity/resistance tests should be logged before, during and after installation.Important notesChoose the kit wattage to match the free floor area, excluding fixtures such as vanities, baths and cabinetry. Do not shorten or cut the heating cable. Register the warranty after installation; the heating element carries a lifetime warranty (conditions apply).Specifications Wattage Coverage (approx.) 300 W 1.4–2 m² 600 W 3.4–4 m² 1000 W 6.1–7 m² 1500 W 9–10.7 m² 3000 W 17.9–21.4 m² 6000 W up to approx. 42 m² SafetyIndoor use only. This is a 230–240 V fixed-wiring appliance: installation and connection must be performed by a licensed electrician in accordance with AS/NZS wiring rules, with the circuit protected by an RCD. Independently tested to AS/NZS standards.
$0.00 - $2,756.05
The Dunlop Non-Slip Bucket Base is a simple but genuinely useful trade accessory made from high-strength rubber. It cradles the bottom of a Dunlop 10L pail and grips the ground beneath it, so your bucket stays planted while you scoop, stir or trowel out product. No more chasing a sliding pail across a smooth floor or steadying it between your feet while you work one-handed.Where to use itSlip it under Dunlop 10L pails and buckets on any job where the pail needs to stay put: mixing and dispensing tile pointing, grouts, renders and adhesives, or working on slick surfaces such as tiled floors, sheet flooring and concrete slabs. It is especially handy with Dunlop Tile Pointing pails on roofs and other awkward spots, indoors or outdoors.Features High-strength rubber construction Sturdy, reliable grip keeps 10L pails stable while you work Sized to suit Dunlop 10L pails and buckets Ideal companion for Dunlop Tile Pointing pails Durable, quality trade accessory CareWipe off spilt render, grout or adhesive before it cures so the rubber keeps its grip. Rinse with clean water when dirty, let it dry completely, and store it flat away from direct sunlight to prevent the rubber degrading.
$19.75
The Dunlop Mixing Paddle is a cost-effective drill-driven paddle that takes the hard work out of blending cement-based products to a smooth, lump-free consistency. Its blade profile is shaped to pull dry powder up from the sides and bottom of the bucket, so every batch is fully combined and ready to apply, with no wasted material left clinging to the pail.Where to use itAttach it to a suitable mixing drill whenever you are preparing mortars, tile adhesives, floor levellers, render, plaster or screeds. It is the natural partner for bagged Dunlop products across tiling, rendering and floor-levelling jobs, and works just as well for small DIY batches as it does for repeated trade mixing on site, indoors or outdoors.Features Mixes mortars, tile adhesives, floor levellers, render, plaster and screeds Blade design lifts dry powder from the bucket sides and base for a complete mix Helps achieve a consistent, lump-free result every batch Cost-effective trade-quality paddle Fits standard mixing drills CareImmediately after mixing, spin the paddle in a bucket of clean water to flush off wet product, then wipe it down before anything sets on the shaft or blades. Dry the paddle before storage to prevent corrosion and check the shaft is straight before each use.
$28.80
The Dunlop Sponge Float is a high-quality finishing float built to produce the classic sponge-finished render surface. Its clever design pairs a sponge face with a perforated aluminium backing plate that allows water to transfer through the back of the float, keeping the sponge working wet so it glides across the render and lifts a fine, even texture rather than tearing the surface.Where to use itUse the sponge float in the final stage of rendering, once the render has firmed enough to be rubbed up. Worked in light circular motions with clean water, it evens out the surface and produces the uniform sponge texture popular on rendered exterior walls. It suits professional renderers chasing a consistent finish as well as DIY users rendering fences, feature walls and home exteriors.Features High-quality sponge float for a sponge-textured render finish Perforated aluminium plate allows water transfer through the back of the float Unique ErgoGrip handle for comfortable, controlled use Ideal for render projects large and small Trade-quality Dunlop construction CareRinse the sponge thoroughly after every session so render particles do not cure inside it, and flush the perforated plate clear at the same time. Squeeze out excess water, let the float air-dry sponge-side up, and store it away from sunlight to stop the sponge hardening or crumbling.
$32.88
The Dunlop Scoop is a high-strength steel scoop designed for renderers and plasterers who need to move, measure and load mixed product quickly and cleanly. Fitted with Dunlop's ErgoGrip handle, it sits comfortably in the hand and stands up to the daily punishment of scooping heavy render, plaster and dry powders on site, helping you keep the job moving with less mess and less strain.Where to use itUse the scoop to transfer dry render, plaster and cement-based powders from bags into mixing buckets, to load mixed product onto a hawk, or to portion material during batching. It is equally handy for tiling and floor-levelling work where accurate, tidy handling of powders and mixed product saves time and reduces waste on both indoor and outdoor jobs.Features High-strength steel construction for lasting durability Comfortable ErgoGrip handle Ideal for renderers and plasterers Makes batching and transferring product faster and cleaner Quality trade-grade tool CareScrape and rinse off render or plaster before it cures, since set material is hard to remove and adds weight to the tool. Dry the steel thoroughly after washing to prevent surface rust, and store it in a dry place with your other rendering tools.
$36.38
The Dunlop Finishing Trowel is a premium stainless steel trowel built to deliver a smooth, professional-grade finish on rendered and screeded surfaces. Its high-strength blade holds a true, flat edge under pressure, while the exposed rivets give visible reassurance of the tool's build quality. The moulded ErgoGrip handle keeps your wrist comfortable through long passes across walls and floors, making it a reliable everyday trowel for renderers, plasterers and serious DIYers alike.Where to use itReach for this trowel whenever you are applying or finishing renders and screeds, indoors or out. It is ideally suited to smoothing acrylic and cement-based renders on walls, flattening floor screeds, and achieving that final glass-smooth pass that separates a professional job from an average one. It pairs naturally with Dunlop render products and a renderer's hawk.Features High-strength stainless steel blade for a superior finish Exposed rivets for visible strength and durability Comfortable ErgoGrip handle reduces hand fatigue Ideal for renders and screeds Premium trade-quality construction CareWash render or screed residue off the blade with clean water before it sets, as cured material is difficult to remove and can pit the surface. Wipe the trowel dry after cleaning and store it flat in a dry place to keep the blade true and rust-free.
$53.63
The Dunlop Wooden Float is crafted from hard-wearing European Beechwood, giving it the slightly open texture that renderers and concreters rely on to close up, flatten and evenly finish freshly applied surfaces. Combined with Dunlop's comfortable ErgoGrip handle, it is a simple, durable tool that helps you work render, concrete and screed to a consistent, professional standard without hand fatigue.Where to use itUse the wooden float for rubbing up and finishing renders on walls, smoothing concrete slabs and paths, and levelling floor screeds. The timber face is particularly good at bringing render to an even, uniform texture before a final sponge or steel-trowel pass, making it a staple for rendering, concreting and general masonry work indoors and outdoors.Features Hard-wearing European Beechwood face Comfortable ErgoGrip handle for extended use Ideal for renders, concrete and screeds Produces an even, consistent surface texture Trade-quality construction at a practical price CareRinse render and concrete off the timber face before it hardens, then allow the float to air-dry fully before storing. Avoid soaking the float for long periods, as excess water can swell or warp the timber. Store it flat in a dry spot away from direct heat.
$54.00
The Dunlop Plastic Float is a quality PVC finishing float designed to close up and smooth freshly applied render. Its lightweight plastic blade glides over the surface without dragging, helping you flatten trowel marks and bring the wall to an even, uniform texture ready for its final finish. Being PVC, it is easy to keep clean and will not rust or swell like some traditional float materials.Where to use itUse it as the render begins to firm up, working the float in even, circular passes to smooth and consolidate the surface. It is ideal for acrylic and cement-based render projects on exterior and interior walls, and its light weight and simple handling make it just as suitable for first-time DIY renderers as for the professionals who use it every day.Features Quality PVC construction for a smooth render finish Lightweight and comfortable to work with over large wall areas Non-rusting, easy-clean plastic blade Ideal for render projects and general finishing work Trade-quality Dunlop tool at a DIY-friendly price CareWash render residue off the blade with water immediately after use, before it can cure onto the plastic. Avoid scraping the face with metal tools, let the float dry fully, and store it flat away from heat so the blade stays straight and smooth.
$23.41
The Dunlop Poly Float is a trade-quality polyurethane float made for finishing renders and screeds to a superior, professional standard. The dense poly face works the surface firmly and evenly, closing pores and levelling small imperfections so walls and screeded floors come up with a consistent texture. It is a straightforward, reliable tool that earns a permanent spot in any renderer's kit.Where to use itUse the poly float once render or screed has been applied and has started to take up, moving it in steady circular or sweeping strokes to flatten and refine the surface. It is equally at home on rendered exterior walls, internal patching work, and sand-cement floor screeds, making it a versatile choice for tradespeople and confident DIYers alike.Features Quality trade poly float for finishing renders and screeds Delivers a superior, professional-standard finish Firm polyurethane face that levels and closes the surface evenly Comfortable to use over large areas Suits both wall render and floor screed applications CareRinse the float clean as soon as you finish a section, since render and screed set hard on the poly face and are difficult to remove later. Dry the tool before storing it, keep it flat, and inspect the face for gouges that could mark future work.
$25.36
The Dunlop Renderers Brush is a trade-quality wetting brush made with natural palm fibre bristles that hold plenty of water. Damping down a wall before render goes on is one of the simplest ways to improve adhesion and workability, and this brush makes that step quick and even, laying down consistent moisture across brick, block and other masonry surfaces before you start applying render.Where to use itReach for this brush at the start of any rendering job to wet down dry, porous substrates so they do not suck moisture out of the fresh render too quickly. It is equally handy for flicking water onto render while sponging and finishing, and suits both professional renderers and DIY users working on exterior or interior walls.Features Purpose-made renderer's wetting brush for damping down surfaces before render is applied Natural palm fibre bristles that hold a generous amount of water Plastic textured handle for a secure grip with wet hands Built-in bucket hook to hang the brush on the lip of your bucket Ideal companion for Dunlop render products CareRinse the bristles thoroughly in clean water after each use so no render slurry hardens in the fibres. Shake out excess water, hang the brush by its hook or lay it flat to dry, and store it out of direct sun to keep the natural bristles in good condition.
$38.11
The Dunlop Renderers Hawk is a trade-quality hand board built for carrying and working render on site. Its plate is made from strong, grooved aluminium that holds a load of render securely at your side, so you can move material from the mixing bucket to the wall smoothly and keep application flowing without constant trips back and forth. A flush plate and the unique ErgoGrip handle keep the tool balanced and comfortable in the hand through long stretches of work.Where to use itUse the hawk on any rendering project, indoors or out, wherever render, patching compounds or similar mortars need to be carried and fed onto a trowel. It suits professional renderers and plasterers as well as home renovators tackling their own walls, and pairs naturally with Dunlop acrylic and fine coat renders.Features Strong, grooved aluminium plate that supports the render during application Flush plate design for clean loading and scraping Unique ErgoGrip handle for comfort and control Ideal for render projects of all sizes Genuine trade-quality Dunlop tool CareScrape off excess render and rinse the plate with clean water before the material sets, as cured render is difficult to remove from the grooves. Wipe the tool dry, check the handle fixing occasionally, and store it flat in a dry place so the aluminium plate stays true.
$62.78
The Dunlop Concrete Edger is a quality stainless steel trade tool designed to put clean, rounded edges on fresh concrete for a truly professional finish. Running the edger along the perimeter of a pour compacts and shapes the edge, reducing the risk of chipping once the formwork comes off and giving slabs, paths and steps a neat, finished look.Where to use itUse the edger on any freshly placed concrete where a formed edge is exposed, such as driveways, footpaths, patios, garage slabs and step treads. Work it along the junction between the concrete and the formwork while the surface is still workable to create a smooth, uniform radius along every edge.Features Hard-wearing stainless steel construction Purpose-made for edging concrete Creates a rounded, chip-resistant edge Delivers a consistent, professional finish Comfortable and easy to control CareRinse the edger clean immediately after use so cement paste cannot cure on the working faces, paying attention to the curved lip. Dry the tool before putting it away and store it where the radius edge will not get knocked or bent, keeping your edges crisp job after job.
$35.53
The Dunlop Concrete Float is a hard-wearing, sides-up float made to deliver a smooth, professional finish on fresh concrete. The blade is manufactured from high-strength stainless steel with exposed rivets that show off the tool's robust construction, while the turned-up sides help the float glide over the surface without digging in. The ErgoGrip handle keeps the tool balanced and comfortable through long finishing sessions.Where to use itThis float is the go-to tool when finishing concrete slabs, paths, driveways and screeded surfaces. Use it after screeding to close up the surface, push down aggregate and bring fines to the top, leaving a flat, even face ready for edging, grooving or final trowelling.Features Hard-wearing sides-up float design High-strength stainless steel construction Exposed rivets for visible strength Comfortable ErgoGrip handle Ideal for concreting and screed finishing CareHose the float down as soon as you finish working, before any concrete hardens on the blade or in the rivets. Dry it off after cleaning and store it flat where the sole cannot get dented or scratched, so it continues to leave a flawless surface on the next pour.
$55.79
The Dunlop External Corner Tool is a stainless steel finishing tool that takes the guesswork out of shaping external corners on rendered surfaces. Its pre-formed angle lets you run a straight, uniform corner in one pass, delivering the kind of sharp, consistent line that is very hard to achieve freehand with a standard trowel. It is a simple tool that makes a visible difference to the quality of a rendering job.Where to use itUse it wherever two rendered walls meet at an outside corner, such as building facades, garden walls, window reveals, pillars and parapets. After applying render to both faces, draw the corner tool down the arris to true up and smooth the junction for a professional result on exterior and interior render work.Features Purpose-made finishing tool for external corners Durable stainless steel construction Produces straight, uniform corner lines Ideal for render projects of all sizes Simple to use for pros and DIYers alike CareWash render off the tool straight after use, before it hardens in the folded angle. Dry the stainless steel thoroughly and store the tool so the formed corner cannot be bent or crushed, as a true angle is what gives you clean corners next time.
$26.01
The Dunlop Gauging Trowel is a versatile hand tool that earns its place in any renderer's or concreter's kit. Built with a high-quality carbon steel blade and finished with Dunlop's distinctive ErgoGrip handle, it offers the strength to mix and scoop cement-based products and the comfort to keep working all day. Its rounded-nose blade shape makes it easy to gauge, transfer and apply material exactly where it is needed.Where to use itUse it across a wide range of jobs, including mixing and placing concrete, screeds, renders and mortar, patching masonry, and roof pointing work. It is just as handy for scooping product from the bucket as it is for working material into tight spots that larger trowels cannot reach, indoors or out.Features High-strength carbon steel blade Unique ErgoGrip handle for added comfort True multipurpose design Suited to concrete, screeds, renders, masonry and roof pointing Compact shape for detail and gauging work CareRinse render, mortar or concrete off the blade before it sets, using a stiff brush for stubborn residue. Because carbon steel can rust, dry the tool thoroughly after washing and consider a light wipe of oil on the blade before storing it in a dry toolbox.
$26.26
The Dunlop Ardit Trowel is a purpose-built floor levelling trowel designed to help you spread and smooth self-levelling compounds to a clean, even finish. The blade is formed from high-strength stainless steel and is reinforced with multiple exposed rivets, so it stays rigid and true even under constant trade use. Dunlop's ErgoGrip handle keeps the tool comfortable in the hand over long stretches of floor, making it easier to maintain consistent pressure and achieve a professional result.Where to use itReach for this trowel when working with floor levellers, screeds and concrete surface repairs. It is ideal for smoothing freshly poured levelling compound before floor coverings go down, and works equally well for feathering out patch repairs on concrete slabs in homes, garages and commercial spaces.Features High-strength stainless steel blade Exposed rivet construction for visible durability Comfortable ErgoGrip handle Suited to concrete, screeds and levelling compounds Helps deliver a smooth, professional-grade finish CareWash levelling compound off the blade with water before it cures, as set material is difficult to remove and can pit the surface. Wipe the tool dry after cleaning, check rivets stay tight, and store it flat in a dry place to protect the blade edge.
$57.21
Dunlop Multipurpose Acrylic Render is a high-performance, polymer-modified render engineered for superior trowelability and a no-sag, no-crack result even at higher builds. It can be applied from 2mm right up to 10mm in thickness without slumping, which makes it equally at home as a levelling base coat over rough masonry or as a straightening coat before a fine or textured finish. One bag covers the jobs a standard sand-and-cement mix struggles with, while remaining easy to rule off and float.Where to use itFor indoor and outdoor rendering over AAC panels and blocks, brickwork, concrete blockwork and concrete walls. Use it to render new masonry, level uneven walls, and build out hollows before finishing with Dunlop Ready-to-Go Render, Fine Coat Render or Coloured Render Texture Coat.How to usePrepare a clean, sound, dust-free substrate and dampen very porous masonry or apply the recommended primer. Mix the powder with clean water to a smooth, workable consistency, then apply with a steel trowel at 2-10mm. Rule off with a straight edge, allow to firm, then float or sponge to the desired surface. The Dunlop Gauging Trowel helps achieve a professional finish. As a guide, 20kg covers approximately 6.5m² at 2mm, 2.6m² at 5mm or 1.3m² at 10mm thickness.Important notesDo not exceed 10mm per coat — build very deep sections in multiple passes. Avoid application in direct hot sun, high wind or onto frozen or saturated substrates, and protect fresh render from rapid drying. Allow to cure fully before over-coating or painting.Specifications Size 20kg bag Colour Light Grey Coverage 6.5m² at 2mm, 2.6m² at 5mm, 1.3m² at 10mm per bag Application thickness 2-10mm SafetyContains cement — wet render is alkaline and can irritate or burn skin and eyes. Wear gloves, eye protection and a dust mask when mixing, avoid breathing dust and wash skin promptly after contact. Read the Safety Data Sheet before use.
$23.55
Dunlop Flexible Fine Coat Render is a high-performance, fibre-reinforced, polymer-modified render that produces a fine, closed finish with superior adhesion and flexibility. The embedded fibres and flexible polymers allow the render to tolerate the minor movement common to sheeted and composite walls, dramatically reducing the risk of surface cracking. It can be applied by standard trowelling methods or by spray, and a variety of decorative finishes can be achieved depending on how it is floated or sponged.Where to use itSuitable for indoor and outdoor use over an unusually wide range of substrates: FC sheet and blueboard, concrete and blockwork, sound painted surfaces (alkali stable and water resistant), existing render, AAC panels and blocks, and EPS foam panels. It is the go-to finishing render where substrate movement or mixed materials would defeat a rigid render.How to useEnsure the substrate is clean, sound and free of dust, oil and loose coatings; prime where the system requires. Mix the powder with clean water to a smooth, lump-free consistency and apply by steel trowel or spray at 2-10mm thickness. Rule off, allow the render to firm, then float, sponge or texture to the desired finish. A 20kg bag covers approximately 6.5m² at 2mm or 2.6m² at 5mm thickness. Clean tools with water before the render sets.Important notesStay within the 2-10mm application range per coat. Avoid rendering in extreme heat, wind or imminent rain, and protect the fresh surface from rapid drying. Painted substrates must be firmly bonded, alkali-stable and water resistant.Specifications Size 20kg bag Colour Grey Coverage 6.5m² at 2mm or 2.6m² at 5mm per bag Application thickness 2-10mm Reinforcement Fibre-reinforced, polymer modified SafetyCement-based powder — the wet mix is alkaline and dust can irritate airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in ventilation and wash skin after contact. Refer to the Safety Data Sheet before use.
$39.21
Dunlop Render Joint & Patch in the 10L trade pail is a high-performance combination product that covers two essential preparation steps in one: jointing fibre cement sheet and blueboard ahead of rendering, and patching cracks and holes up to 5mm in existing rendered walls. Premixed to a smooth, light grey consistency, it goes straight from pail to trowel with no mixing, keeping preparation fast and consistent across large jobs. The 10L size is the economical choice for renderers and builders working across full elevations or multiple rooms.Where to use itIndoors and outdoors on walls. Use as a jointing compound over blueboard and fibre cement sheeting before render systems are applied, and as a patching compound over sound existing render to make good cracks, holes and surface defects up to 5mm deep or wide before re-rendering, texture coating or painting.How to usePrepare a clean, dry, sound surface free of dust, loose material and contaminants. Trowel the compound firmly across sheet joints, embedding jointing tape where required by the sheet manufacturer, and feather the edges flush. For patching, press the compound into the defect, strike off level and smooth the surface — the Dunlop Gauging Trowel helps achieve a professional finish. Allow to dry completely before over-coating, and clean tools with water while the product is still wet.Important notesRepairs deeper or wider than 5mm need staged applications or a dedicated repair mortar. Cold, damp or humid weather extends drying times. Do not use across designed movement joints — finish those with a flexible sealant.Specifications Size 10L pail Colour Light Grey Patch capacity Cracks and holes up to 5mm (depth or width) Location Indoor and outdoor walls SafetyWater-based product. Wear gloves and eye protection during use, avoid prolonged skin contact and wash exposed skin with water. Store sealed, keep away from children and consult the Safety Data Sheet before application.
$117.64
Dunlop Flexible FC Jointing Compound in the 8kg trade pail is a premixed, flexible jointing compound for fibre cement sheet and blueboard, formulated to prepare sheet joints before decorative coatings, texture finishes or render go on. Ready to use straight from the container, it removes mixing from the workflow entirely and keeps a consistent, workable body from the first trowel-load to the last. Its flexible acrylic formulation moves with the substrate to resist joint cracking, while strong adhesion keys the compound firmly to the sheet surface.Where to use itFor jointing fibre cement sheeting and blueboard on interior and exterior walls — cladding, facades, garage conversions, extensions and commercial sheeted walls — prior to painting, texture coating or rendering. The larger pail suits whole-wall and multi-room jobs where a 3kg pack would run short.How to useCheck that sheets are rigidly fixed and joints are clean, dry and dust-free. Apply the compound over each joint with a trowel or broad knife, embedding jointing tape where the sheet manufacturer requires it, then finish with a band approximately 75mm wide and 1mm thick, feathered smooth at the edges. Allow to dry completely before over-coating. Wet compound cleans off tools with water. Coverage is approximately 7 lineal metres per kilogram at 75mm width and 1mm thickness, so an 8kg pail joints in the order of 55 lineal metres.Important notesDesigned movement joints should be finished with a flexible sealant rather than jointing compound. Drying slows in cold or humid weather. Keep the lid sealed between uses and do not thin the product with water.Specifications Size 8kg pail Colour Grey Coverage Approx. 7Lm per kg (75mm wide at 1mm thick) Location Indoor and outdoor walls SafetyWater-based acrylic product. Wear gloves and eye protection during application, avoid prolonged skin contact and wash with water after use. Store sealed in a cool place away from children and refer to the Safety Data Sheet before starting.
$92.06
You have seen 192 out of 498 products
Professional-level performance for strength, durability and productivity on site. Expect defined movement capability, temperature/chemical ratings and precise application methods. Use filters to refine by chemistry and pot life. Always review the product page and TDS/SDS.
