Marathon Scale and Rust Remover CONCENTRATED 2L Bottle Tough on calcium, rust and scale deposits. Ideal to use on tiles, porcelain, sinks, showers and baths
$7.00
PC-Crete™ Epoxy is a hand-mixable, fast-setting epoxy putty that quickly repairs concrete and masonry. After mixing, it forms a concrete repair polymer that cures to a concrete-like color and texture. The mixture readily sticks to concrete and masonry surfaces and is easily shaped. It will stick to ceramics, glass, metals and some plastics. It cures within 60 minutes. Each stick contains pre-measured portions of activator and base — no measuring or mixing tools are necessary. Here are just a few specific uses (there are hundreds of other uses): Quickly rebuild small missing pieces of concrete Fill holes in concrete and masonry Rebuild missing pieces of statues and birdbaths Seal hole for wire or conduit thru cinder block Fill chip or spall in concrete furniture Reattach loose or popped decorative stone Fill crack in stone fireplace Fill holes in brick or concrete walls; Apartment complexes, schools, government buildings etc. Fill cracks in concrete or stucco wall before painting Attach address numbers to brick or stone Attach hardware to brick or stone Fill abandoned screw holes and mounting holes in brick or cinderblock Replace missing mortar Seal rodent hole in cinderblock or concrete How to prepare a surface for bonding with PC-Crete™ Old concrete must be clean and profiled or textured. Surface must be clean and sound. It may be dry or damp, but free of standing water. Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Crete™ application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. Can PC-Crete™ be used to repair a crack in a fountain? PC-Crete™ looks like concrete and is excellent for repairing concrete fountains, statues and lawn decorations. Will PC-Crete™ adhere to a concrete step? Can it be shaped to match a corner? PC- Crete™ is excellent to repairs on concrete surfaces such as steps. It shapes easily and can be sanded to match the look and texture of the concrete surface. Is PC-Crete™ suitable for filling a small crack or spall in a sidewalk or deck? Small crack repairs in concrete are easily made with or without the use of tools using PC-Crete™. PC-Crete™ is excellent for replacing missing or loose mortar between bricks and stones. Can PC-Crete™ be used in a fish tank or pond? PC-Crete™ is not recommended for aquatic use. Do not use this product in aquariums or ponds. The PC-Crete™ is not easily grabbing or sticking to the concrete surface. It pulls away lifting loose stones The putty wants to stick to the fingers more than the concrete surface. Wet the fingers with alcohol and then press, shape and smooth the applied putty. Also, loose stones can be wire brushed away to provide a sound surface. PC-Crete™ does not have a smooth texture. It has particles throughout The particles in PC-Crete™ are used to simulate the appearance of concrete.
$16.17
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
Interior and exterior use Acetic cure Excellent bond to glass Parfix Window & Glass Silicone is suitable for use on windows, glass partitions and glass blocks. Ideal for both interior and exterior use, Parfix Window & Glass Silicone is an acetic cure silicone with that bonds securely to glass, providing a water tight and UV resistant seal.
$11.57
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$9.35
Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, and holds up to 6.8kg! (15 pounds) Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features 6.8KG Strong Hold - Sticks to smooth and rough surfaces.* Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How much weight will Gorilla Mounting Tape hold? Gorilla Black Mounting Tape will hold up to 30 (13.6KG) pounds per project. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface. If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur. If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.
$17.95
Betta Tilecare Tile & Grout Sealer waterproofs porous tiles and grout without leaving a slippery film coating, making it perfect for kitchens, bathrooms, and other tiled areas. Drying Time: Recoat: 15 minutes Full Dry: 24 hours Coverage: 1L covers 5-10m² Available Sizes: 1L, 4L, 300g Aerosol, 500ml Wheel Applicator, 750ml Trigger Application Method & Cleanup: Tools: Paint brush, roller, or pump spray Features: Water-based formula Clear penetrating finish Invisible, moisture-repellent coating Easy to use Proven technology Non-slip finish Preparation: Remove any silicone sealant strips and soap build-up. Clean mould off tiles and grout using Betta Tilecare Mould Rid™ or bleach. Rinse thoroughly with water after cleaning. Remove and patch all loose or missing tile grout. For improved results, add Bondall HydroCrete to the grout mix. Ensure the application area is dry for 12-24 hours before applying the sealer. For porous surfaces or after high-pressure washing, allow 3-4 days drying time before sealing. Application: Start from the top of the wall, applying Tile & Grout Sealer liberally over tiles and grout. Finish by applying the sealer to the shower base or floor. Ensure even coverage across all surfaces. Drying: Wait at least 15 minutes for the first application to react before reapplying. After the second application, wait another 15 minutes, then use a dry cloth to remove any excess from the tile surface. Allow 24 hours before using the sealed area. Tips & FAQs: Not for Water Holding Vessels: This product is not intended for waterproofing items like ponds or fish tanks. Test Before Use: Always test on a small, inconspicuous area to ensure it provides the desired result. Avoid Over-application: If the sealer runs or pools, wipe down with a clean, dry, low-lint cloth. Apply Evenly: Take care to apply evenly, especially on pitted surfaces. Pre-treat Stains & Mould: Ensure stains, moss, and mould are treated prior to sealing. Avoid Pooling: Do not allow the product to pool or over-apply on surfaces. Betta Tilecare Tile & Grout Sealer is a reliable and easy-to-use product for waterproofing and protecting your tiles and grout, providing long-lasting protection without altering the natural appearance of your surfaces.
$27.91
Betta Tile Care Tile & Grout Sealer Betta Tilecare Tile & Grout Sealer waterproofs porous tiles and grout without leaving a slippery film coating. Drying Time: Recoat: 15 minutes Full Dry: 24 hours Coverage: 1L covers 5-10m² Finishes: White in the pail, dries clear Ideal For: New & old grout (clean) Unsealed and/or porous tiles Application Method & Cleanup: Tools: Paint brush, roller, pump spray Features: Water-based Clear penetrating finish Invisible moisture-repellent Easy to use Proven technology Non-slip Preparation: Remove silicone sealant strips and soap build-up. Clean mould off tiles and grout using Betta Tilecare Mould Rid™ or bleach. Rinse thoroughly with water after cleaning. Patch any loose or missing tile grout. For improved results, use Bondall HydroCrete as a grout additive. Ensure the application area is dry for 12-24 hours before applying Tile & Grout Sealer. For porous surfaces or after high-pressure washing, allow 3-4 days drying time before applying the sealer. Application: Start at the top of the wall and brush Tile & Grout Sealer liberally over the tiles and grout. Finish with the shower base or floor, ensuring thorough application to all surfaces. Drying: Allow 15 minutes for the first application to react, then reapply over the entire area. After the second application, wait 15 minutes for penetration, then wipe off any excess with a dry cloth. Allow 24 hours for full drying before use. Betta Tilecare Tile & Grout Sealer is the perfect solution for sealing and protecting both new and old grout, ensuring your surfaces stay waterproof and protected without compromising safety.
$26.77
Selleys Rapid Mould Killer is a fast-acting spray that tackles stubborn mould and mildew in and around the home. Formulated for busy bathrooms, laundries and other damp, mould-prone areas, it gets to work almost immediately, destroying visible mould in as little as 30 seconds and eliminating 99.9% of germs on treated surfaces. The 750ml trigger pack delivers plenty of product for larger jobs, with a twist nozzle that switches between a fine spray and a targeted stream. Key features Effectively eradicates stubborn mould and mildew Fast acting – destroys visible mould in around 30 seconds Eliminates 99.9% of germs on hard surfaces Adjustable spray/stream trigger nozzle for controlled application Generous 750ml size for larger and more frequent jobs Where to use it Indoors: Ideal throughout the bathroom and laundry – on tiles and grout, shower screens, shower curtains, toilets, rubber bath mats, plastic surfaces and other mould-affected areas. Outdoors: Suitable for spot-treating mould-affected exterior surfaces where staining and mould have taken hold. How to use Twist the nozzle to either SPRAY or STREAM. Spot test on an inconspicuous area first. Spray directly onto the mould-affected surface. Leave for about 30 seconds, then rinse, wipe or scrub off. Important notes On some matt-finish tiles or in hard-water areas, staining may occur – always patch test first. Not suitable for fabric, mirror tiles, metallic surfaces, or older baths and basins. Do not mix with other cleaners. Specifications Brand Selleys Product Rapid Mould Killer Size 750ml Format Ready-to-use trigger spray Action Destroys mould in ~30 seconds; kills 99.9% of germs Best for Bathrooms, laundries, toilets and other mould-prone areas Suitable surfaces Tiles, grout, shower screens, shower curtains, plastic, rubber bath mats Safety This is a bleach-based (sodium hypochlorite) mould killer. Use in a well-ventilated area and wear suitable gloves and eye protection. Avoid contact with skin, eyes and clothing. Never mix with other cleaning products or acids, as hazardous chlorine gas can be released. Keep out of reach of children, rinse treated surfaces after use, and store upright in a cool place away from direct sunlight. Always read the label and refer to the manufacturer’s Safety Data Sheet before use.
$10.79
Dunlop Flexible Coloured Grout is a smooth-finish, flexible cement-based grout available in a wide palette of popular colours to complement almost any tile. Its stronger colour formula gives rich, consistent joints, while built-in Grout Shield anti-mould and anti-bacteria technology resists mould and bacteria growth to keep wet areas looking fresher for longer. Easy to work and forgiving to clean off, it ensures flush joints with no pin holes.Where to use itUse it on walls and floors, indoors and outdoors, with ceramic, porcelain, marble, granite and mosaic tiles. It handles joints from 1mm right up to 8mm, so one product covers both fine wall joints and wider floor joints. For swimming pools, use the White 200 colour mixed with Dunlop Primer & Additive.How to useMake sure joints are clean, dry and raked clear of adhesive. Mix the powder with clean water (or with Dunlop Primer & Additive for extra flexibility, adhesion and stain resistance) to a smooth paste. Spread diagonally across the tiles with a rubber float, packing joints full, then sponge the surface clean once firm and buff off the haze. Initial set occurs after about 24 hours; showers can be exposed to water after 3 days, the grout can be sealed after 3 days and full cure is reached in 7 days.Important notesCoverage depends on tile size, joint width and depth - allow around 15% wastage. Colour can vary slightly with water content and curing conditions, so mix consistently between batches.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing mixing dust, and wash after use. Keep out of reach of children; refer to the Safety Data Sheet.
$15.23 - $15.24
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $11.03
Glitz Daily Shower Cleaner Prevents Soap Scum Build Up 750ml Keep your shower looking fresh with this easy daily spray. Glitz Daily Shower Cleaner helps prevent soap scum and mineral build up so glass, tiles, and fittings stay clearer for longer. No heavy scrubbing required. Just spray and go as part of your routine. Key benefits Helps stop soap scum forming between deep cleans Cuts through light residue from body wash and shampoo Streak free finish on shower screens when used as directed Fast application for busy bathrooms Fresh clean scent that leaves the space smelling pleasant Where to use Shower glass and screens Ceramic tiles and grout surrounds Fibreglass and acrylic bases Chrome and stainless steel fittings Sealed stone and laminate surfaces in wet areas Always test first on an inconspicuous spot. Avoid unsealed stone, marble that is not sealed, brass, copper, and any surface that is not water safe. How to use After showering, quickly rinse surfaces with warm water. Set nozzle to spray. Mist evenly over glass, tiles, and fittings. Leave to work. No rinse required on light residue. For heavier build up, wipe with a soft cloth or squeegee. Use daily to help prevent soap scum returning. Pro tips Keep a squeegee in the shower and pull down glass before spraying for the best clarity. Ventilate the bathroom to reduce fogging and moisture marks. Pair with a weekly deep clean for grout lines and corners. Good to know Non abrasive formula suitable for regular use Safe for most sealed surfaces when used as directed Family friendly routine cleaner for shared bathrooms Specifications Product Daily shower maintenance spray Size 750 ml trigger bottle Suitable surfaces Glass, ceramic tile, acrylic, fibreglass, chrome, stainless steel, sealed stone Finish Clear streak free when wiped or squeegeed Use frequency Daily after showering Safety Read label before use. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other cleaners. Store upright in a cool dry place. Frequently asked questions Do I need to rinse after spraying For light daily residue, no rinse is needed. For visible build up, wipe or squeegee for a clear finish. Will it remove heavy limescale It is designed to prevent and control light residue. For stubborn limescale, use a suitable descaler first then maintain with daily use. Is it safe on natural stone Use only on sealed stone. Test first and avoid unsealed or delicate stone surfaces. What is in the box 1 x 750 ml Glitz Daily Shower Cleaner with adjustable trigger
$11.61 $10.44
Glitz Sugar Spray Soap Paint Prep and Surface Cleaner 450g Get surfaces paint ready with a fast acting sugar soap spray that cuts through everyday grime, grease, and fingerprints. Glitz Sugar Spray Soap makes prep quick and consistent so your paint, sealant, or wallpaper has a clean base for better adhesion and a smooth finish. Why you will love it Ready to use spray for quick coverage on walls, doors, trims, and tiles Lifts grease and grime to help paint stick and level more evenly Low streak formula wipes off clean and rinses easily Great for general household cleaning between projects Convenient 450 g can for easy storage in the toolkit or under the sink Ideal surfaces Painted plasterboard and brick Doors, skirting, window frames Tiles, laminate, vinyl, benches sealed against moisture Outdoor furniture and exterior trims that are sound and sealed Not recommended on Unsealed or raw timber Natural stone that is unsealed Waxed, oiled, or polished finishes Delicate plastics or lacquered metals that may mark How to use for paint prep Shake well. Protect floors and nearby furnishings. Spray a light, even coat on the area to be cleaned. Allow 1 to 2 minutes to penetrate built up grime. Wipe with a clean damp cloth or non scratch pad. Rinse the surface with clean water and allow to dry fully before sanding or painting. Tip: Always test on a small hidden spot first to confirm compatibility. General cleaning For everyday mess, spray, wipe, and rinse. For stubborn marks, repeat as needed. Product details Brand Glitz Product Sugar Spray Soap Paint Prep and Surface Cleaner Pack size 450 g Format Ready to use spray Appearance Clear liquid cleaner Suitable for Interior and exterior cleaning prior to painting Clean up Wipe and rinse with water Safety Wear gloves for extended use. Avoid contact with eyes and skin. Use in a well ventilated area. Do not inhale spray. Keep out of reach of children and pets. Do not mix with other cleaners or chemicals. Storage and disposal Store upright in a cool, dry place away from direct sunlight. Dispose of empty container in accordance with local regulations. Frequently asked questions Do I still need to rinse before paintingYes. Rinsing removes any remaining residue and helps paint adhere better. Can I use it on glossy trimsYes, but rinse well and allow to dry, then lightly sand if your paint system recommends it. Will it remove mould stainsIt removes general grime. For mould staining, clean first with a dedicated mould remover, then prep with this spray, rinse, and dry fully. Good to know Perfect as the first step in any repainting job Helps reduce fisheyes and adhesion issues caused by hidden grease Glues Australia ships fast Australia wide. Order today to get your prep done right.
$5.40 $4.83
Glitz Cleaning Vinegar Natural Eco Multi Purpose Cleaner 2L Make everyday cleaning simple with this powerful plant based vinegar cleaner. It cuts through grease, soap scum, water marks and light mineral deposits while leaving hard surfaces streak free. Ideal for kitchens, bathrooms, windows and floors, all in one generous 2L value pack. Why you will love it Natural cleaning power that tackles grime without harsh chlorine or ammonia. Streak free finish on glass, stainless steel and glossy tiles. Deodorises bins, laundry and pet areas with a fresh, clean scent. Concentrated value that you can use neat for tough spots or dilute for everyday mopping. Family friendly fragrance free formula suitable for regular cleaning. Eco mindful choice in a recyclable bottle. Where to use Kitchen benches, splashbacks and sinks Cooktops and stainless steel appliances Showers, taps, tiles and grout Windows, mirrors and glass doors Floors including sealed vinyl, sealed timber and tiles Laundry deodorising and general wipe downs Not recommended on Natural stone such as marble, limestone, travertine or unsealed granite. Avoid use on waxed or oiled timber, unfinished metals, electronics and any surface that is not water safe. Always spot test in a hidden area first. How to use General spray and wipe: Add to a trigger bottle. Light soils 1 part vinegar to 3 parts water. Spray, wipe clean, then dry with a lint free cloth. Glass and mirrors: Dilute 1 part vinegar to 4 parts water. Spray lightly and polish dry. Bathrooms: Use neat on soap scum and tapware. Apply, leave 2 to 3 minutes, scrub if needed and rinse well. Dry metal surfaces after rinsing. Floors: Add 1 cup to a 5L bucket of warm water. Mop and allow to air dry. Deodorise: Lightly mist bins or laundry tubs, then rinse or wipe after a few minutes. Tips for best results Do not mix with bleach or products containing bleach. Rinse natural rubber and metals after contact. Use microfiber cloths for a streak free finish. Product details Brand Glitz Product Cleaning Vinegar Natural Eco Multi Purpose Cleaner Size 2L Format Ready to use or dilute as directed Fragrance Fragrance free with mild vinegar scent Surface compatibility Glass, stainless steel, ceramic, enamel, chrome, sealed tiles, sealed timber, vinyl Bottle HDPE recyclable Safety Keep out of reach of children and pets. Avoid contact with eyes and prolonged skin contact. If in eyes, rinse with water. Do not ingest. Do not mix with other chemicals. Store upright in a cool, dry place with cap closed. Frequently asked questions Can I use it on stone benchtops? No. Acids can etch natural stone. Use a stone safe neutral cleaner for marble, limestone, travertine or unsealed granite. Is it safe for stainless steel? Yes for quick wipe downs. Spray onto a cloth, wipe, then buff dry. Always rinse and dry taps and fittings. Can I use it in a steam mop? Check the appliance instructions. If additives are not recommended, use the floor dilution in a regular bucket and mop instead. What is included 1 x Glitz Cleaning Vinegar Natural Eco Multi Purpose Cleaner 2L Shipping and pickup Fast dispatch Australia wide from our Melbourne warehouse. Click and Collect available on request. Contact us to arrange a pickup time.
$3.89 $3.29
Strengthen critical junctions and stop leaks before they start. Crommelin Waterproofing Tape is a flexible, self-adhesive reinforcing tape designed to bridge cracks, joints, and movement-prone areas so your waterproofing membranes and sealants perform at their best. Why you will like it Reinforces weak points at wall to floor junctions, around drains, over hairline cracks, and along internal corners. Excellent adhesion to common building surfaces when used with compatible primers and membranes. Flexible backing conforms to corners and curves to maintain a continuous seal. Moisture barrier assist helps reduce the risk of water ingress beneath tiles and finishes. Easy to cut and apply for fast prep on bathrooms, balconies, laundries, and wet areas. Ideal for Showers, bathrooms, and laundries Balconies and terraces before tiling Planter boxes and upstands Penetrations such as pipes and wastes Internal corners, junctions, and small static cracks Quick specs Product Waterproofing reinforcement tape Length 5 m Finish Flexible tape for embedment into compatible membranes Typical surfaces Concrete, rendered masonry, fibre cement, primed timber, sealed gypsum, existing compatible membranes Application Hand applied, press firmly with roller or trowel How to use Prepare the area. Surface must be clean, dry, sound, and free of dust, oils, and loose material. Prime as required by your chosen waterproofing membrane system. Measure and cut lengths to suit corners, junctions, and penetrations. Pre fit to check placement. Bed the tape into the first wet coat of compatible membrane or approved adhesive. Press firmly to remove air pockets and ensure full contact. Overlap joins by at least 50 mm. At corners, mitre or fold neatly so the tape remains flat without creases that could trap water. Topcoat with additional coats of membrane to fully encapsulate the tape, observing required dry times between coats. Cure the membrane system as directed before tiling or finishing. Good to know Cover the tape with a compatible liquid membrane. Do not leave exposed to prolonged UV. Always follow the membrane manufacturer instructions for primers, coat thickness, and cure times. If in doubt about compatibility, perform a small adhesion test on your substrate and membrane. Storage and safety Store in a cool, dry place away from direct sunlight. Wear gloves and eye protection during surface prep and membrane application. Dispose of offcuts and packaging according to local regulations. What is in the box 1 roll Crommelin Waterproofing Tape, 5 m length Glues Australia helps Australians fix and protect with confidence. If you need help choosing a compatible membrane or primer for this tape, contact our team.
$39.15 $30.48
Stop leaks fast with Fastfix Waterproof Repair Tape. This heavy duty, self-sealing tape forms a tough barrier that helps block water, air and moisture on a wide range of materials. Keep a roll in the toolbox, the ute or the caravan for quick fixes at home or on site. Creates a waterproof seal on clean, dry surfaces Extra thick backing with strong adhesive for a reliable hold Sticks to PVC, metals, plastics, rubber, vinyl, glass, ceramics and more Great for gutters, downpipes, garden hoses, pool gear, tents and tarps Easy to apply by hand with no special tools required Suitable for indoor and outdoor use Where it works Gutters and roof flashings Downpipes and irrigation fittings Garden hoses and pool hoses Camping gear such as tents and tarps Boat covers and awnings Plastic bins, storage tubs and general repairs How to use Clean and dry the area. Remove dust, oil and loose paint. Cut a piece of tape that overlaps the repair by at least 25 mm on all sides. Peel the liner and position the tape carefully. Avoid touching the adhesive. Press down firmly from the centre out to the edges to remove air bubbles. For higher pressure or larger repairs, apply a second layer with the seam offset. Allow time under firm pressure to achieve the best bond. Good to know Best adhesion on smooth, non-porous surfaces. Not a substitute for structural repairs. For wet or submerged applications, bond strength can vary depending on surface and water pressure. Test on a small area first if surface is delicate or freshly painted. Specifications Brand Fastfix Product type Waterproof repair tape Size 50 mm width x 5 m length Colour Black Adhesive Pressure-sensitive Finish Flexible, conformable backing Suitable environments Indoor and outdoor Storage Store cool and dry, out of direct sunlight. Keep liner on until use.
$21.52 $18.69
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$9.49
Wet-area rated hanging solution for towels and robes. Water-resistant adhesive Designed for bathrooms and laundries Simple, tool-free install Examples of use: Add a towel point near a vanity Place a robe hook by the shower Create a guest towel spot
$8.81
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$17.01
Replacement adhesive strips to reuse your existing Command hooks and hangers. Fresh adhesive for reliable hold Easy to apply and remove cleanly Sized to fit matching hooks Examples of use: Refresh worn strips on bathroom hooks Swap seasonal decor without new hardware Rehang key rails and caddies
$5.29
Clear mini hooks sized for kitchen tools and lightweight accessories. Food-area friendly surfaces Removes cleanly Compact, clear design Examples of use: Hang measuring spoons by the stove Hold tea towels or oven mitts Store small gadgets on a splashback
$18.06
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$10.79
Picture hanger engineered for wire-back or sawtooth frames with stable support. Quick stick-on install Clean removal with no wall damage Keeps frames level Examples of use: Hang framed art and certificates Display mirrors within weight rating Mount signage in halls
$8.56
Wet-area rated hanging solution for towels and robes. Water-resistant adhesive Designed for bathrooms and laundries Simple, tool-free install Examples of use: Add a towel point near a vanity Place a robe hook by the shower Create a guest towel spot
$23.60
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$16.95
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$11.00
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$6.76
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$7.34
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$7.34
Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.
$79.80
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Selleys Sealant & Adhesive Remover 375g helps soften and lift old sealants and sticky residues so you can cleanly remove them and re-seal with confidence. The non-drip formula clings to joints and vertical surfaces, making bathroom and kitchen refreshes faster and easier. Key benefits Softens cured silicone and many common sealants to aid scraping and removal Helps break down adhesive residue, tapes and grime build-up Non-drip gel action for vertical joints, corners and trims Low mess application with excellent wetting of tight gaps Preps surfaces for fresh re-sealing and re-bonding Where to use Bathrooms: around showers, baths, basins and splashbacks Kitchens and laundries: benchtop perimeters, sinks and tiles Windows and doors: frames, trims and glazing edges Suitable substrates Glass, ceramic tiles, porcelain, enamel, stainless steel and many metals Some plastics and laminates (always test first in an inconspicuous spot) Not recommended on Natural stone, marble or porous tiles Freshly painted, delicate or lacquered surfaces Acrylic and polycarbonate sheets, mirror backings and other sensitive plastics Directions Cut away and remove as much old sealant as possible with a plastic scraper. Protect surrounding areas. Shake or stir if required, then apply a generous layer to remaining residue. Allow time for the remover to penetrate. Dwell time will vary by sealant type and thickness. Gently scrape and wipe away loosened material. Reapply if needed for stubborn spots. Wash the area with warm soapy water, rinse and dry thoroughly before re-sealing. Pro tips Score thick beads along the edges with a utility blade before application to help penetration. Work in manageable sections and avoid letting the remover dry on the surface. Always test on a small hidden area to check surface compatibility. Safety Use in a well ventilated area and wear gloves and eye protection. Avoid contact with skin and eyes. Keep out of reach of children. Product details Brand: Selleys Type: Sealant and adhesive remover Pack size: 375g
$38.69
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.98
Tarzan's Grip Mounting Tape is a double sided, heavy duty, high strength tape that instantly grabs for easy, fast and permanent mounting. It is ideal for a multitude of surfaces, including metal, wood, rubber, leather, china, brick, stone, plasterboard and most plastics. Extremely strong Instant grab Solvent free Permanent
$12.42
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes. Easy mix Durable bond Dries clear Water resistant
$13.39
SikaBond Fast is a premium, water-based, multi-purpose construction adhesive providing strong initial grab and high bond strength. Uses: SikaBond Fast can be used on most substrates due to its excellent adhesion. These include: - Fixing polystyrene wall panels - Replacing loose tiles on walls - Skirting boards, architraves and trims to walls - Bonding panels to wall studs - Bonding particleboard, plywood, fibre cement and strip flooring to joists Advantages : - Complies to AS2329-1980, “Mastic Adhesives for Fixing Wallboards” - Natural wood colour - Reduces the number of mechanical fasteners required to install floors or walls. - Can be repositioned for up to 60 minutes after application - Reduces squeaking associated with nail ride in floors - Paintable with water-based surface coatings - Easy to use one component - Bridges gaps up to 9 mm - Strong adhesion to metal - No fumes - High bond strength and heat resistance - Flows easily at all temperatures - Easy cleanup - Fast initial grab – minimises slippage on vertical surfaces Storage and Shelf Life Stored in the original sealed packaging at temperatures of between 5oC and 35oC, this material will keep for at least two (2) years. Instructions for Use Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking material must be removed and light sanding is recommended. SikaBond Fast will adhere to damp (not wet) substrates but drying times may increase. Substrates should be above 5ºC. Do not bond 2 non-porous substrates ensure that one surface is porous. Application Apply a 5 mm bead of SikaBond Fast to one surface using a cartridge gun; ensure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges. Cleaning The uncured material can be cleaned with water. The hardened material can only be removed by mechanical means. Technical Data (Typical) Colour Pale Brown Specific Gravity ~ 1.4 Skinning Time 20 minutes Repositioning Time 60 minutes Full Cure 24 hours depending on conditions When both surfaces are porous firm, a slip-resistant bond will develop after 15 minutes at 30ºC and 60 minutes at 10ºC. Should one surface be non-porous or the substrate damp, a firm slip resistant bond will be achieved in approximately 8 hours. After 24 hours, 90% of the final strength will be achieved. (dependant on temperature, the porosity of the substrates, humidity and ventilation). Service temperature -5ºC to +90ºC Packaging 420 gram cartridge (12 cartridges per box)
$8.69
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$24.57
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.60
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$21.93
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$12.50
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. Safety tips If swallowed, do NOT induce vomiting. Avoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$20.69
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$16.56
You have seen 96 out of 381 products
Find products tagged for use on tiles. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on tiles surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
