Mixing Nozzles

Sika AnchorFix 3001 Epoxy Chemical Anchoring Adhesive 250 ml Sika AnchorFix 3001 is a two part, high performance epoxy anchoring adhesive for fixing threaded rods, bolts, and reinforcement bars into cracked or uncracked concrete and other solid substrates. It delivers very high load capacity, reliable performance in damp concrete, and a long open time that makes placement simple on site. Why choose AnchorFix 3001 High load capacity with shrinkage free cure Works in dry or damp concrete and overhead locations Long open time for easier installation Seismic tested C1 and fire resistant Styrene free and low wastage Approved for contact with drinking water Typical uses Rebar and threaded rod anchoring in new builds and refurbishments Fixing balustrades, handrails, supports, and railings Securing window and door frames and general metalwork Suitable substrates Concrete cracked or uncracked Solid and hollow masonry Natural and reconstituted stone Wood and solid rock Key approvals Complies with NCC reference to AS 5216 design of post installed fastenings in concrete Potable water approved to AS 4020 ICC-ES ESR-3608 for anchoring in cracked concrete under static, wind, and earthquake loading Specifications Chemistry Epoxy, two part 1 to 1 by volume Colour Mixed grey Density Approx 1.49 kg per L Service temperature Long term from minus 40 °C to plus 40 °C Compressive strength Approx 85 N per mm² at 7 days Tensile strength Approx 23 N per mm² at 7 days Mixing Static mixer nozzle supplied, standard sealant gun for 250 ml Packaging 250 ml cartridge Shelf life 24 months unopened at 10 to 25 °C in dry storage Open time and cure guide Substrate or ambient temperature Open time Full cure +25 to +30 °C About 8 minutes About 6 hours +20 to +25 °C About 11 minutes About 7 hours +15 to +20 °C About 15 minutes About 8 hours +10 to +15 °C About 20 minutes About 12 hours +5 to +10 °C Use with warmed cartridge minimum 10 °C About 24 hours How to use Drill the hole to the specified diameter and depth for the anchor size. Clean thoroughly. Blow out dust with oil free compressed air and brush with a steel hole cleaning brush. Repeat the blow and brush steps to remove all fines. Fit the static mixer. Dispense material until a uniform grey appears and discard the first small amount. Inject from the bottom of the hole while withdrawing the nozzle to avoid trapping air. For deep holes use an extension tube. In hollow masonry use a perforated sleeve. Insert the anchor with a slow rotary motion until set at depth. Excess resin should slightly extrude. Do not disturb or load until the full cure time has elapsed for the temperature. Good to know Non sag formula for overhead applications Ensure substrate is sound, clean, and at least 3 °C above dew point Clean tools immediately after use. Cured material must be removed mechanically What is included One 250 ml cartridge with static mixer nozzle. Applicator gun not included. Storage Store sealed in a cool, dry place between 10 and 25 °C. Keep out of direct sun and away from moisture. Safety Read the Safety Data Sheet before use. Wear suitable PPE and provide ventilation. Keep out of reach of children.

Read more less

For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: clean and degrease the plastics first for a stronger bond (no primer required). Loxeal Superlox Polyolefin Bonder 25ml Bi-Syringe (Single) Loxeal Superlox is a two-part acrylic adhesive developed to bond polyolefins, polypropylene (PP), polyethylene (PE), HDPE and LDPE, and other notoriously difficult low-surface-energy plastics, without primers, flame treatment or other expensive surface pre-treatments. This listing is for a single 25ml bi-syringe supplied with a mixing nozzle, dispensing the two components at a simple 1:1 ratio, so you can buy just what one job needs. It joins polyolefins to each other and to other plastics such as ABS and PVC, and to metals, producing structural joints with high shear and peel strength. Why choose Loxeal Superlox? Bonds the "unbondable", PP, PE, HDPE and LDPE plus other low-surface-energy plastics No primer or surface pre-treatment required, clean, apply, assemble Single 25ml bi-syringe with mixing nozzle, fresh adhesive for the job at hand Simple 1:1 mixing ratio through the supplied static mixing nozzle Structural performance, high shear and peel strength on plastics and mixed-material joints Also bonds polyolefins to other plastics (ABS, PVC) and to metals Typical applications Repairing and fabricating PP and PE components: tanks, housings, containers, piping and trim Joining polyolefin parts to dissimilar plastics or metal brackets and fittings Manufacturing and maintenance work on low-surface-energy plastic assemblies How to use Clean the surfaces to remove dust, oil and grease (for example with Loxeal Cleaner 10) and allow to dry. Fit the static mixing nozzle to the bi-syringe and discard the first few centimetres of extruded adhesive. Apply the mixed adhesive to one surface. Assemble the parts promptly and hold or clamp them without movement while the adhesive sets. Leave the joint undisturbed until fully cured before applying load. Cure times Fast curing at room temperature, parts typically fixture within minutes of assembly Allow 24 hours for full strength before placing joints under working load Refer to the Technical Data Sheet for precise fixture and cure data for your conditions Specifications Chemistry Two-part structural acrylic, polyolefin bonder Mixing ratio 1:1 by volume via static mixing nozzle Key substrates PP, PE, HDPE, LDPE and other low-surface-energy plastics; also ABS, PVC and metals Surface preparation No primer or pre-treatment required, clean and dry surfaces only Strength profile High shear and peel strength Pack size 1 x 25ml bi-syringe with mixing nozzle Buying more than one? If you use Superlox regularly, the Superlox trade pack of 10 x 25ml bi-syringes works out cheaper per syringe. Important notes Work at room temperature; low temperatures slow the cure Use each mixing nozzle for one continuous application, fit a fresh nozzle if work is interrupted Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and avoid skin and eye contact. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal Metalox Metal Repair Epoxy 25ml Bi-Syringe (Single) Loxeal Metalox is a solvent-free, fast-curing, metal-filled two-part epoxy engineered for repairing and bonding metal components. This listing is for a single 25ml bi-syringe supplied with a mixing nozzle, so you can buy exactly what one job needs without committing to a trade pack. Its thixotropic (non-sag) paste works as an adhesive filler, rebuilding metal castings, pipework and flanges, and once cured it can be machined, sanded and painted, typically within a few hours of application. Why choose Loxeal Metalox? Single 25ml bi-syringe with mixing nozzle, accurately proportioned 1:1 dispensing on every repair Fast cure, handling strength in around 15 minutes, sandable in about 5 hours at room temperature Strong on steel, lap shear strength of 21 N/mm² on grit-blasted mild steel Machinable, sandable and paintable after polymerisation, even for outdoor repairs Non-sag thixotropic paste stays put on vertical and overhead surfaces Excellent resistance to water and many chemical agents Heat cure option: 1 hour at +60°C speeds cure and boosts final strength Typical applications Repairing metal castings, pipework and flanges Automotive body repair and panel filling Bonding metal substrates, plus concrete, wood and other rigid materials Maintenance and plant repairs where downtime must be kept short How to use Scratch or abrade the surface, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the bi-syringe and discard the first 3 to 5 cm of extruded product. Apply the mixed adhesive directly to the repair area; work at temperatures above +15°C. Assemble or shape immediately and leave undisturbed until cured. Once cured (sandable after about 5 hours at +25°C), machine, sand or paint as required. Cure times Pot life: approximately 5 minutes at +25°C Handling strength: approximately 15 minutes Sandable: about 5 hours at +25°C (90% of final hardness) Accelerated cure: 1 hour at +60°C for full resistance sooner Specifications Chemistry Two-part epoxy (resin / amine hardener), metal-filled Colour Part A metallic grey / Part B black Mixing ratio 1:1 by volume Pot life (+25°C) Approx. 5 minutes Handling strength Approx. 15 minutes Lap shear strength (ISO 4587) 21 N/mm² (grit-blasted mild steel); 18 N/mm² (stainless steel) Compression strength (ASTM D695) 60 N/mm² Hardness (ISO 868) Shore D 65 Pack size 1 x 25ml bi-syringe with mixing nozzle Shelf life 24 months unopened at +5°C to +25°C Buying more than one? If you go through Metalox regularly, the Metalox trade pack of 10 x 25ml bi-syringes works out cheaper per syringe. Important notes Apply at temperatures above +15°C; higher temperatures and large mixed quantities reduce pot life Avoid mixing excess product, the curing reaction generates heat Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Wear suitable gloves, avoid skin and eye contact, and work in a well-ventilated area. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal 31-42 Clear 5-Minute Epoxy Adhesive 50ml Dual Cartridge Loxeal 31-42 is a two-part, fast-setting structural epoxy that cures colourless and transparent, making it ideal for repairs where the glue line needs to stay invisible. Supplied in a convenient 50ml dual cartridge (1:1 ratio) with a mixing nozzle, it dispenses perfectly proportioned adhesive with no weighing or hand mixing. With a working time of around 5 minutes and handling strength in 20–30 minutes, it bonds metals, ferrite, ceramic, marble, glass, concrete, wood and some rigid plastics. Why choose Loxeal 31-42? Dries clear – colourless, transparent bond line suits glass, ceramics and visible repairs Fast 5-minute set – 3–8 minute working time, functional strength in 20–30 minutes No-mess 1:1 dual cartridge with mixing nozzle for accurate, on-part dispensing Gap filling from 0.1 to 2.0 mm for less-than-perfect joints Durable bonds with excellent resistance to water, gasoline, motor oil and cooling gas Easy enough for DIY, strong enough for the workshop Typical applications Structural bonding of metals, ferrite, ceramic, marble, glass, concrete and wood Bonding some rigid plastics such as polyester, ABS and rigid PVC Joining dissimilar materials in one fast operation Household, automotive, hobby and workshop repairs needing a clear, rigid bond How to use Lightly abrade the surfaces, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the cartridge and discard the first 3–5 cm of extruded adhesive. Apply the mixed adhesive directly to one surface. Assemble the parts immediately and hold them together, without mechanical stress, until handling strength is reached. Remove uncured excess with acetone or a compatible solvent-based cleaner; cured adhesive can only be removed mechanically. Cure times Pot life (working time): 3–8 minutes at +25°C Functional cure: 20–30 minutes at +25°C Strength continues to develop over the following hours; gentle heat accelerates cure Specifications Chemistry Two-part epoxy (resin / amine hardener) Colour (mixed) Colourless / transparent Mixing ratio 1:1 by volume Pot life (+25°C) 3–8 minutes Functional cure 20–30 minutes Shear strength (steel, ISO 4587) 12–14 N/mm² Peel strength (ISO 4578) 4–20 N/25mm Hardness Shore D 65–75 Gap fill 0.1–2.0 mm Service temperature -40°C to +80°C Pack size 50ml dual cartridge (DCT) with mixing nozzle Shelf life 1 year unopened at +5°C to +25°C Important notes Not suitable for rubber, soft materials, polyethylene (PE), polypropylene (PP) or PTFE Apply at temperatures above +15°C; higher temperatures shorten pot life Avoid mixing large volumes at once – the chemical reaction generates heat Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Work in a well-ventilated area, avoid skin and eye contact, and keep out of reach of children. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

Read more less

Sika AnchorFix®-1 is a high-performance, styrene-free chemical anchoring adhesive designed for fast and reliable installations in both construction and DIY projects. This two-component, solvent-free, polyester-based adhesive is ideal for securing rebars, threaded rods, bolts, and special fastening systems in concrete, hollow and solid masonry, hard natural stone, and solid rock. It cures rapidly, even in low temperatures, and can be applied using standard guns. Advantages: Fast curing Compatible with standard guns Usable in low temperatures High load capacity ETA approved Non-sag, even overhead Styrene-free Low odor and wastage Technical Information: Compressive Strength: ~60 N/mm² (7 days, +20°C) Modulus of Elasticity in Compression: ~3,500 N/mm² Tensile Strength in Flexure: ~28 N/mm² Tensile Strength: ~12 N/mm² Temperature Resistance: +50°C (long-term), +80°C (short-term) Glass Transition Temperature: +60°C Color: Component A: White Component B: Black Mixed: Light grey Usage: Ideal for various grades of rebars, threaded rods, bolts, and special fastening systems. Substrates may vary, so testing is recommended to ensure suitability, especially with natural stones. Always ensure the substrate is clean, dry, and free of contaminants. Perform pull-out tests if the substrate strength is unknown. Mixing and Application: Mix the components in a 10:1 ratio by volume. The material must be between +5°C and +40°C for application. Ensure the substrate temperature is between -10°C and +40°C. Shelf Life and Storage: Shelf life is 12 months from the date of production when stored properly. Store in unopened, sealed, and undamaged packaging in dry conditions between +5°C and +25°C. Curing Times: +30°C: Open time 4 minutes, Curing time 35 minutes +25°C: Open time 4 minutes, Curing time 40 minutes +20°C: Open time 5 minutes, Curing time 50 minutes +10°C: Open time 6 minutes, Curing time 85 minutes +5°C: Open time 10 minutes, Curing time 145 minutes -10°C: Open time 30 minutes, Curing time 24 hours Approvals and Certifications: Complies with NCC 2019 reference to AS 5216:2018 for post-installed and cast-in fastenings in concrete. ETA-approved for use in masonry and non-cracked concrete, with CE marking. Cleaning of Equipment: Clean tools with Sika® Colma Cleaner immediately after use. Hardened material can only be removed mechanically. For detailed design considerations, refer to "Technical Documentation Sika AnchorFix®-1" (Ref: 870 43 01).

Read more less