![Selleys Wet Area Sealant EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens. Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away Mould resistant Precision application for the best finish Where can this product be used? Showers Baths Spas Sinks Metal, copper and brass plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Powder coated aluminium Aluminium Plastic laminates Rubber Glass Stainless steel Concrete Size 100g Aerosol can Technology Neutral Cure Silicone Use Interior How to Use Use in a well ventilated area. Avoid contact with skin and eyes. 1. Throughly clean and dry surface from oil, dirt and grease with mineral turps. 2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. 3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap 4. Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Sealant is not paintable.Complete painting 7days prior to applying sealant. • Not for aquariums or contact with food, eating utensils or drinking water.
$14.77
![Selleys Wet Area Sealant EZI Press [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens. Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away Mould resistant Precision application for the best finish Where can this product be used? Showers Baths Spas Sinks Metal, copper and brass plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Powder coated aluminium Aluminium Plastic laminates Rubber Glass Stainless steel Concrete Size 100g Aerosol can Technology Neutral Cure Silicone Use Interior How to Use Use in a well ventilated area. Avoid contact with skin and eyes. 1. Throughly clean and dry surface from oil, dirt and grease with mineral turps. 2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. 3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap 4. Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Sealant is not paintable.Complete painting 7days prior to applying sealant. • Not for aquariums or contact with food, eating utensils or drinking water.
$21.37
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$22.44
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697132673_9813d4fc-b7c0-4502-8c30-7f4b7f7d7408.webp?v=1754716190&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697132673_a62141c0-14b4-4be3-9f3d-e9bbf8e3ce89.webp?v=1754716190&width=645)
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout) The product also contains fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour so can be used in any environment without discomfort. Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam. Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. Temperature resistance – approximately -60°C +150°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Where can this product be used? Showers and sinks. Metal, copper and brass fittings. Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper and brass fitiings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal. Handy tips Tips for Using a Silicone Sealant in a Wet Area Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$13.74
Sil-X advanced polymer technology is formulated to deliver superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Sil-X has been specially developed to withstand the tough Australian and New Zealand conditions. Selleys THE ONE Adhesive delivers superior bond strength on any building surface. Can be applied to wet or dry, interior or exterior, porous or non porous surfaces*. Extreme versatility that takes the guess work out of DIY. Features Strong bond on any building material Can be applied to wet or dry surfaces Suitable for interior and exterior applications Can be used on porous and non-porous materials Will adhere to oily surfaces Low VOC Excellent weather resistance Flexible and long lasting Paintable with water-based paints What materials is this product suitable for? Suitable for all building materials* How to use this product Ensure surfaces are clean and free from grease or loose particles. Cut tip of cartridge, fit nozzle and cut at 45ºangle to desired size before placing in a cartridge gun such as Selleys Light Speed Caulking Gun. Apply with a caulking gun, pushing adhesive onto the surface. Position pieces and press firmly together. Larger, heavier materials may need to be supported until the adhesive cures. If painting, paint with water-based paint. Handy tips Keep a pack of SELLEYS Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. Limitations *Not for PE, PP, PTFE, or permanent water immersion Clean up Clean up with turps before the adhesive cures. Safety tips Keep out of reach of children. Avoid skin and eye contact and breathing vapours. Use in a well ventilated area. Wear protective clothing, gloves and eye protection. If on skin, wash with soap and water. Cure product before disposal. Product releases methanol during cure.
$17.00
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/9300697128881_05baffa7-20d9-4ff2-9039-79bd0c8a796b.png?v=1754711779&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/9300697126047_24fe6e74-fe07-4d10-9db0-38dc98c383c8.png?v=1754711781&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
Selleys Storm Waterproof Tape is a quick and easy way to seal and patch most objects*. It can be applied in the rain to stop leaks in an instant. Storm Waterproof Tape stops water leaks for 48 hours, making it ideal for emergency fixes until permanent repairs can be made. Features Waterproof & airtight seal* – Wet or Dry Stops active water leaks for up to 48 hours* Sticks to wet surfaces* Removable Suitable for interior and exterior Suitable for fresh, salt & chlorinated water Easy-to-use, DIY optimised format Where can this product be used? Can be used on gutters & flashing, down pipes, caravans, tents & tarps, rubber/plastic/vinyl pool liners, PVC piping, inflatable pool toys, small boats & kayaks air mattresses, umbrellas and more! Suitable for Aluminium, Galvanised Steel, Colorbond® Steel, Copper, Brass, Fibreglass, some rubbers and plastics* Ensure surface is free of dirt, grease and oil Cut tape or patch to desired size. Ensure there is at least 2-3cm of tape extending beyond each edge of the hole Remove backing paper, position carefully and press down firmly Once in position, rub firmly to ensure no air or water bubbles are left under the tape, and ensure good contact between the tape and substrate Leave tape until permanent repairs can be made
$25.00
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$12.46
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$40.95
![Selleys Roof and Gutter EZI Press [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
Selleys Roof & Gutter Ezi Press is easy to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and excellent UV and weather resistance. Ideal for roofing, guttering and flashing outside the home. Best for: Aluminium, Sheet Metal, Copper, Brass, Galvanised Metals, Rigid PVC and most plastics including polystyrene, Terracotta, Concrete, Glazed tiles, BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away UV and weather resistant Precision application for the best finish Where can this product be used? Metal and tile roofing Colorbond roofs and fences Guttering and flashings Skylights Around air conditioning units What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Galvanised Metals Rigid PVC and most plastics including polystyrene Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND Use in a well ventilated are. Avoid contact with skin and eyes. Throughly clean and dry surface from oil, dirt and grease with mineral turps. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Do not use in below ground applications. • Sealant is not paintable. Complete painting 7d prior to applying sealant.
$29.04
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$10.84
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$7.40
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697128836_d8030407-bb46-4243-8f8f-670a3627cc7e.png?v=1754711816&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$18.09
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697128843_fcf51f23-ec41-4a49-aaee-70cab0a2903b.jpg?v=1754711818&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$18.09
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697128812_e6db645e-770f-466e-b839-e1436d775f7c.jpg?v=1754716162&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/93006971288_e5c72006-3593-4105-a377-2e2ef8783219.png?v=1754716162&width=645)
$22.84
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697128805_ad4032a6-f03b-4931-a88d-54b5bfce27d3.jpg?v=1754716159&width=645)
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/93006971288.png?v=1754716159&width=645)
$22.84
This multipurpose silicone is a neutral (non-acid) curing, one part sealant for interior and exterior use. It is specially formulated to seal out water in a wide variety of situations, where an excellent quality flexible seal with outstanding adhesion is required. Superior adhesion. Non shrinking. Mould resistant. Low odour. Non corrosive.
$19.00
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
$27.01
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$9.73
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to respond to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. If there is old difficult to remove residue such as old flaky paint, we recommend using paint stripper such as SELLEYS KWIK STRIP SMART, and allow to dry. On wet timber pooled water should be wiped off. Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/ Course grain, as the construction adhesive will adhere more readily to a scratched up surface. Cut the seal at the top of the cartridge. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of work which requires a caulking gun. Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining. The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days. When the product is still wet it can be removed with mineral turpetine, otherwise if the product is dry it can be removed by sanding or scraping, we recommend using a 50mm ROTA COTA Soft Grip Scraper. Clean any excess from your hands with SELLEYS Hand Kleen Wipes. To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid nails into the groove or each board when installing. Handy tips When applying to one surface, ensure sufficient LIQUID NAILS Original is used so that some adhesive extrudes out when surfaces are brought together then wipe off excess if necessary. If glue is not visible, then insufficient contact may not have been made between the surfaces and a weak joint may result. LIQUID NAILS Original should always be used in conjunction with mechanical fasteners in structural, critical or high stress applications. LIQUID NAILS Original is sometimes called LIQUID NAILS (SOLVENT) to differentiate it from the other Liquid Nails products. LIQUID NAILS Original shrinks slightly on curing. Cured LIQUID NAILS Original residues can be removed by holding a rag soaked in Mineral Turps against the residue, then rubbing the residue once softened. Mineral Turps penetrates in this way at approximately 1 mm per hour. When Liquid Nails Original joints are directly exposed to the weather, it is recommended to seal around the edges with a silicone sealant to prevent water ponding inside the joint and thus weaken the joint. LIQUID NAILS Original is NOT recommended for use on mirrors or polystyrene. Use LIQUID NAILS MIRROR METAL GLASS for mirrors and LIQUID NAILS FAST for polystyrene. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
$5.45
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$13.10
Selleys KwikGrip Spray 350g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 350g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$28.46
Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 150g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$13.60
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$28.95
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$12.78
Selleys Liquid Nails Instant Hold is a high performance advanced polymer construction adhesive that delivers an instant hold on any building material*, even vertical surfaces. It is heat, UV and water resistant and doesn’t require fasteners or clamps for many applications so you can get on with the next job. Powered by Sil-X Advanced Polymer Technology. Features Instant Hold on any building material* Up to 400kgs M2 No need to clamp* High Strength & flexibility Indoor/Outdoor Adheres to wet and damp surfaces and can be applied on wet surface^ Cure time of 48 hours Paintable after 24 hours with water based paints. Solvent based paints may be used after first painting with a water based paint Adjustable e.g. can be straightened for up to 15 minutes Powered by Sil-X Advanced Polymer Technology *Holds instantly but must not be disturbed until fully cured. Weight is restricted for non-porous substrates including metal & glass – support may be required where the object exceeds 5kgs. ^Not for permanent water immersion What Materials is this product suitable for? Timber MDF Plasterboard Some plastics Masonry Concrete Particleboard Metals Glass Tiles & ceramics How to use the product Ensure surfaces are clean and free from grease or loose particles Use a high thrust caulking gun and the supplied V-notch nozzle to apply in vertical stripes 5cm apart. Ensure the V shape is angled upward when applying. Position materials and press together firmly. Due to the high initial hold of the product support during curing is not necessary (subject to weight limitations for non-porous surfaces). Holds instantly but must not be disturbed until cured (up to 48 hours). Adjustable e.g. can be straightened for up to 15 minutes Handy Tips Clean up with turps before the adhesive cures Safety Information KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well ventilated area. Wash hands after use. If on skin: Wash with soap and water. Product releases methanol during cure. Refer to Safety Data Sheet. Storage & re-use Cure product before disposal Store in a cool place. The adhesive should be used within 6 months after opening. If the adhesive is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess adhesive from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be disposed.
$18.00
Features Simply sticks almost anything without screws or clamps* Instantly holds even on vertical surfaces* Adjustable for up to 15 minutes UV & water-resistant Holds up to 360kg/ m² Where can this product be used? Indoors and outdoors for any bonding applications What materials is this product suitable for? Glass Metals Timber Brick Concrete / masonry Tiles Not for polyethylene, polypropylene or teflon Colours White Technology Sil-X® Use Interior Exterior How to use Make sure surfaces are clean, free from grease, girt and grime. Sand back any loose or peeling surfaces. Pull off cap, unscrew nozzle and pierce membrane with the tip of the nozzle. Replace nozzle and cut along the second ridge. Cover one surface in the adhesive in long vertical strips. After applying the adhesive, press surfaces together firmly, ensuring the adhesive spreads. Clean up any excess product with methylated spirits.
$20.78
Features Simply sticks almost anything without screws or clamps* Instantly holds even on vertical surfaces* Adjustable for up to 15 minutes UV & water-resistant Holds up to 360kg/ m² Where can this product be used? Indoors and outdoors for any bonding applications What materials is this product suitable for? Glass Metals Timber Brick Concrete / masonry Tiles Not for polyethylene, polypropylene or teflon Colours White Technology Sil-X® Use Interior Exterior How to use Make sure surfaces are clean, free from grease, girt and grime. Sand back any loose or peeling surfaces. Pull off cap, unscrew nozzle and pierce membrane with the tip of the nozzle. Replace nozzle and cut along the second ridge. Cover one surface in the adhesive in long vertical strips. After applying the adhesive, press surfaces together firmly, ensuring the adhesive spreads. Clean up any excess product with methylated spirits.
$16.76
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$17.30
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$20.98
Fast setting supa glue that dries colourless and sets in 10 seconds. Features Bonds a variety of surfaces Quick setting – only takes 10 seconds Dries clear, therefore no mess No mixing required No clamping necessary Heat resistant: approx 80C maximum Non toxic when set Water resistant Application range: -55°C to +80°C Where can this product be used? Ideal for small repair jobs or when immediate results are required Supa Glue will bond non-porous surfaces Supa Glue is water resistant not water proof, so do not use in areas continually exposed to moisture as it will weaken the bond. Supa Glue is generally not flexible and has low impact resistance. ie will probably shatter if dropped. For these applications use SELLEYS Quick Fix Shock Proof or SELLEYS Urethane Bond. Supa Glue’s bond strength is excellent where surfaces to be bonded are a good close fit. Where gap filling is required use SELLEYS URETHANE BOND or ARALDITE or for very minor gap filling you can use SELLEYS Quick Fix Gel. Supa Glue is not recommended for use on paper. Not suitable for bonding plastics such as polyethylene, polypropylene or Teflon?. Supa Glue will not permanently bond glass or materials containing alkaline elements. What materials is this product suitable for? Rubber Some plastics Wood Metals How to use this product The seal at the end of the metal tube should be pierced carefully with the reverse end of the cap. Ensure that the tube is not squeezed while the seal is being pierced. Replace plastic nozzle. Surfaces to be bonded should fit exactly and should be clean, dry and free of dust, dirt and grease. Apply a drop of Supa Glue to only one of the surfaces to be joined. Use sparingly. Do NOT spread. (Note: One drop covers an area 25mm x 25mm)KEEP FINGERS AWAY FROM EXCESS ADHESIVE SO THEY WILL NOT STICK TOGETHER. Quickly align both surfaces and apply slight pressure to ensure effective spreading and bond. Should you fail to align the surfaces correctly, do not attempt to re-align them and bond together again. Keep apart and completely clean the surfaces (with acetone or nail polish remover). When dry, re-apply adhesive, re-align and bond again. (Please Note: NOT ALL Nail Polish Removers are ACETONE.) Although the adhesive will grab after several minutes to provide sufficient bond strength for practical use, maximum bond strength is achieved after 12 hours. Wipe tip of tube and replace cap. Handy tips Once open, Supa Glue has a limited shelf life (i.e. up to 1 year provided the tip is wiped clean and the cap replaced securely after each use). Supa Glue vapour can produce a whitening effect in enclosed spaces. To avoid this use in well ventilated areas. The whitening effect can be removed by wiping with acetone (first check that the acetone will not damage the surface). To remove from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Note: This method should only be used for substrates NOT adversely affected by exposure to solvents. Check a small area before use. Storing in a refrigerator can reduce the risk of hardening in the tube. Also leaving a pin stuck in the (cleaned) nozzle during storage can reduce the risk of the nozzle becoming clogged with cured adhesive which is difficult to clear. One drop covers an area 25mm x 25mm Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. Since Supa Glue cures with moisture set times may be extended on very dry surfaces or under dry conditions. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Avoid contact with skin and eyes and avoid breathing its vapour. Supa Glue bonds on contact. Should fingers stick together, apply a solvent such as acetone to contact areas, then wash skin with water. Do NOT use solvents in contact with eyes or open wounds. In case of eye contact, immediately flush with water and seek medical attention. When removing Supa Glue from the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. If poisoning occurs, seek medical attention. Cured material is considered to be non-hazardous. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use Ensure cap is replaced and store in a cool dry place. Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$15.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$7.42
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$16.79
Selleys Ezy Tack – Sticking things together, modelling, holding small objects, filling small gaps – people use Ezy Tack in hundreds of different ways. It is ideal for non-porous surfaces such as glass or metal, painted surfaces, vinyl coated wallpaper etc. Ideal for: Sticks memos & posters Position table/office deco Holds wall hanging & craft Features: Ezy Tack can be reused. Simply roll into a ball in your hand. Non-toxic Directions: Ensure surfaces are clean, dry, free from grease and lose materials. Tear off the amount you require, knead until supple. Roll into a ball. Place between surfaces to be fastened and press firmly, Ezy Tack performs best on non-porous surfaces, vinyl coated wallpapers, painted surfaces, glass, metal, etc. To remove Ezy Tack, ROLL IT OFF CAREFULLY from the surface. Any remaining shreds can be removed by rolling or dabbing a bigger piece of Ezy Tack over the area. Handy Tips: Do not use Ezy Tack on absorbent, silk-screen printed, hand-stencilled wallpaper, or recently decorated surfaces. On some surfaces, Ezy Tack may leave a faint oily mark but this can be removed using a citrus based stain remover. The adhesive qualities of Ezy Tack increase with time, so take extra care when removing it after a period of time.
$4.02
Liquid Nails Heavy Duty is a multipurpose construction adhesive that delivers extreme strength in a shorter space of time. The product is specifically designed for those demanding high performance applications, like attaching heavy or bulky materials, panelling, stone tiles, timber and furniture. Best of all it delivers heavy duty adhesion faster so you can get on with the next job. Features 2 X more strength than Liquid Nails Original in less than half the time Speed of cure means mechanical fasteners can be removed after 8 hours compared to 24 hours for Liquid Nails Original No slump or stringing, even when applying a bead to overhead surfaces Excellent resistance to water and weather makes it suitable for interior and exterior applications Easy to extrude from the cartridge at low winter temperatures Where can this product be used? Sheet flooring to joists Metal or aluminium door strips to floors and walls Timber or fibre cement sheeting to cement block or brick walls Masonite / hardboard to timber or floorboards Wallboard or panelling to wood or metal frames Cork tiles to timber, fibre cement or plaster Timber flooring to yellow tongue in conjunction with mechanical fixings to avoid later squeaking What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Glass Tiles & ceramics How to use this product Avoid contact with skin and eyes. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. Cut cartridge tip, fit nozzle and cut end to desired opening. (Approx 5 mm diameter). WET BOND METHOD Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40 cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are repositionable for up to 15 mins after fitting. Allow adhesives to set (at least 8 hours) before removing any temporary fasteners or clamping.(Refer to Bond Strength Time.) CONTACT BOND METHOD – for faster grab Apply a bead to one surface only, press together and pull apart. Allow surfaces to dry 2-4 minutes before firmly joining. Surfaces should not be kept apart for longer than 10 minutes as to do so will impair bond strength Flooring: When fixing sheet flooring (e.g. particleboard), use in conjunction with flooring manufacturer’s installation specifications for minimum nailing requirements. Note: To eliminate squeaks in tongue and groove flooring, use Liquid Nails Heavy Duty in conjunction with mechanical fixings. Handy tips Time for strong bond depends on nature and condition of application. In most situations^ strong bond can be achieved after 8 hours and will continue to strengthen over a 2-3 day period. Full cure can take up to 7 days. ^Curing is achieved by evaporation of solvent. The time required to achieve the bond’s full strength is increased by: constant low temperatures; thick applications (joints) are used; wide areas are bonded; and when bonded surfaces are impervious (e.g. metals and dense timbers).
$11.01
D-MASTIC is an oil-based sealant that forms a skin on exposure to air but remains soft underneath. Designed for sealing windscreens in cars, boats, trucks, and buses, and for metal lap joints in white goods, caravans, bus and truck bodies. Features Forms a surface skin, preventing transfer by touch and dirt pick-up on exposed surfaces Paintable with most alkyd and water-based paints (after the skin has formed). Easy clean-up off non-porous surfaces with mineral turpentine. Convenient to use non-slumping from vertical joints and easily extrudable. Long "open" time assists in the assembly of lap joints. Where can this product be used? Metals Paintwork Lacquered Work Machinery and Engines Sealing windscreens Metal lap joints in whitegoods and automotive bodies What materials is this product suitable for? Metal Glass Painted Surfaces Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as mineral turps. Cut nozzle supplied at an angle and to the required opening. Cut tip off cartridge, fit nozzle and insert in suitable caulking gun such as Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply D-Mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps or kerosene. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Maximum service is achieved when used within joints; it is not recommended to be used as a"skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with a spatula dipped into mineral turps. Uncured product may be removed with mineral turps or kerosene. Cured product can be removed by cutting and scraping.
$21.55
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$19.06
![Selleys Butyl Mastic Rubber Caulking Compound for Vehicles [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697101495_09a144af-33d1-46e0-9c47-6910c6f2672a.jpg?v=1754711927&width=645)
Selleys Butyl Mastic is a synthetic resin, butyl rubber based mastic which forms a smooth tough skin, but remains permanently plastic underneath. It is available Off White. Features Remains permanently plastic under a smooth tough skin Versatile sealant with excellent adhesion to a variety of substrates without the necessity to prime Will not bleed into porous surfaces Non-sag in joints up to 12mm vertical joint Wide service temperature: –35° to +65°C Excellent weathering characteristics Does not corrode metals Good water resistance Life expectancy is approximately 5 years in a thick joint. It is recommended to use silicone sealant in thinner joints Easy smoothing and clean-up with mineral turps or white spirits Where can this product be used? Sealing aluminium windows to masonry. Sealing joints between pre-cast concrete panels or porcelain enamelled panels. Sealing edges of all types of wallboards or wherever a permanent waterproof seal is required. Sealing lap joints between metal applications with the inclusion of fasteners. Ideal for dust proofing cars, trucks, caravans, boats, etc. and is suitable for sealing cracks and gaps around brickwork, roofing and cladding. What materials is this product suitable for? Please contact your store to confirm avaliability, as some stores may have a limited range. The following should only be used as a guide and the installer should apply all Australian Standards, BCA/NZBC requirements, and best practices when installing. Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as white spirits. Cut nozzle supplied at an angle and to the required opening. Cut end off nipple on cartridge, fit nozzle and insert in suitable caulking gun such as the Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of Butyl Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply Butyl Mastic by forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Should not be used where joint movement will exceed ±8%. Maximum service is achieved when used within joints; it is not recommended to be used as a "skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. Surfaces must be clean and dry. Life expectancy in joints is approximately 5 years Interior applications may have greatly extended skin over time due to the reduced presence of sunlight. Allow surface to skin before painting, i.e. approximately 24 hours after application. Butyl Mastic can be painted over using oil or water based paints after the surface has skinned.
$33.47
Selleys MarineFlex delivers a waterproof seal for joints & gaps, even under water*. Suitable for boats, pools & spas. MarineFlex high-performance adhesive sealant can be used on boats, pools & spas, where you need a waterproof seal or bond, even underwater* It can be applied & will cure under water – no need to drain your pool or spa. Compared to traditional polyurethanes it provides a more durable seal & bond with superior UV resistance. Features Salt, fresh & chlorinated water (pools/spas)^ Above and below the waterline No primer required Shock absorbing & vibration dampening Solvent & isocyanate free Sandable when fully cured Powered by Sil-X advanced polymer technology Limitations #Not suitable for PP, PE or PTFE *critical seals/repairs underwater should be regularly checked & repaired if required. Not for polycarbonate and Perspex underwater ^Gelcoat must be lightly sanded prior to product application Where can this product be used? Suitable for boats, pools & spas^ What materials is this product suitable for? Metals Glass Ceramic Tiles Sealed/painted timber & concrete Fibreglass Gelcoat* Most plastics# (pre-test before use)
$23.20
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$32.27
![Selleys Armour Flex High Performance Adhesive [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125286_24a1028f-4655-4200-8859-8e45b8c9ab19.jpg?v=1754711936&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around the pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Appearance Translucent Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing a loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bonding sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquefy slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non-toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$70.21
A new high-performance epoxy adhesive that applies to wet or dry surfaces for complete waterproof bonding. Trust Selleys Aqua Fix to stick when wet – even underwater Features Can be applied to wet and dry surfaces 100% Water resistant Use on multiple surfaces Strong durable bonding Sticks and sets underwater Withstands thermal and mechanical shocks Temperature range -15°C (continuous) to +80°C (intermittent) Colour Dries off white What materials is this product suitable for? Tiles Metal Timber Rubber China Glass Leather Most plastics (not for polyethylene, polypropylene) How to use this product Ensure surfaces to be bonded are clean, free of grease, dirt and lose materials. For best results roughen bond area, prior to cleaning. Carefully cut the sealed tips at the end of the syringe nozzle. Dispense equal parts onto a clean disposable surface and mix together thoroughly to a uniform colour. Mixed glue remains usable for 1 hour. Apply mixed glue to both surfaces of the job then bring together. Do not apply undue strain to bond for 6-8 hours. Hold joint in place using tapes, clamps or weights if necessary for 24 hours. When applying underwater ensure mixed glue is pushed onto the surface firmly until the glue displaces water and adheres to surface. Handy tips For Aquariums allow to cure for at least 72 hours, then thoroughly wash out with water, drain and refill before introducing fish. Not approved for contact with drinking water – use Selleys Knead-It Aqua. Storage and re-use Place cap from plunger on the nozzle for storage Clean up uncured Aqua Repair Glue with acetone (nail polish remover) Safety tips KEEP OUT OF REACH OF CHILDREN Avoid contact with skin and eyes Avoid breathing vapour Wear eye protection and protective gloves when mixing or using. This product is classified as hazardous. Avoid contaminating waterways with uncured product. For frequent hobby or occupational use, refer to the Safety Data Sheet for more information before using the product.
$22.00
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$13.57
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$16.93
You have seen 96 out of 283 products
Find products tagged for use on glass. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on glass surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
