Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, and holds up to 6.8kg! (15 pounds) Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features 6.8KG Strong Hold - Sticks to smooth and rough surfaces.* Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How much weight will Gorilla Mounting Tape hold? Gorilla Black Mounting Tape will hold up to 30 (13.6KG) pounds per project. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface. If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur. If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.
$17.95
Dunlop Revive & Shine Dunlop Revive & Shine is a neutral, multipurpose cleaner and maintainer that enhances the appearance of sealed floors. Designed for use on timber, vinyl, and laminate floors, this product reduces the appearance of scuffing, increases durability, and improves gloss levels. For best results, use monthly to keep your floors looking their best. Key Benefits: Cleans and maintains timber, vinyl, and laminate flooring Provides extra durability, wear resistance, and shine Increases slip resistance Reduces the appearance of scuffing Ideal for monthly maintenance Suitable For Use On: Timber, vinyl, and laminate flooring Surface Type: Floors Location: Indoor Colour & Sizes: Colour: Milky (Dries Clear) Size: 500ml Item Code: 19882 Directions for Use: Dilution: Mix 20mL of Dunlop Revive & Shine per 1L of warm water in a bucket. Cleaning: Mop the floor with the solution. Spills: For spills, hose down the area and wash with large amounts of water. Note: The use of Personal Protective Equipment is recommended during application. Dunlop Revive & Shine is perfect for keeping your timber, vinyl, and laminate floors looking like new, providing enhanced shine, durability, and slip resistance.
$21.46
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$9.16
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
Selleys All Fix Big Jobs is a convenient all-rounder adhesive that sticks just about anything to anything. It provides virtually instant grab on dry porous surfaces eliminating the need for nails and screws on many jobs. It is a heavy-duty adhesive that will bond a wide variety of materials, has low fumes, and conveniently cleans up with water. Features Fast - virtually instant grab on dry porous surfaces eliminates the need for nails and screws on many jobs Fast grab minimises the need for clamping Strong - Heavy-duty adhesive that will bond a wide variety of materials Safe - Low odour, low fumes and non-flammable Dries white and is able to be painted over once dry Lots of working time - bonds can be repositioned within 5-10 minutes Easy to use Fills minor gaps in uneven surfaces (bridges gaps up to 9mm) Strong bond on porous surfaces after 24 hours, cures to maximum strength over a few days Where can this product be used? Re-adhering carpet House numbers to brickwork Wooden furniture repairs Repairing damaged plasterboard Building a dog house Skirting boards Attaching architraves Attaching wall panelling Attaching chair (dado) rails Attaching or building a shelf Use for larger interior projects What materials is this product suitable for? Plasterboard Cabinet Plaster coving Carpet Wood Particleboard Metals (other surface must be porous) Glass (other surface must be porous) Ceramics (other surface must be porous) Brick (other surface must be porous) Concrete Cork Polystyrene foam (other surface must be porous) UPVC (other surface must be porous) Many rigid plastics* (other surface must be porous) Loose wall tiles (in non-wet areas) How to Use Surfaces to be bonded must be dry, sound and free from grease/oil and dust. Work tube between fingers for several seconds to loosen contents. Cut the tip of the nozzle and squeeze to apply adhesive onto one surface. Immediately press parts firmly together. Bonds can be repositioned for up to 5 minutes. If adhesive surfaces form a skin no bond will form. The bond will usually have good strength after 24 hours and will continue to strengthen for a few days. Application Tips For long narrow attachments (e.g. skirting boards) apply one or two continuous beads. For larger flat areas use beads approximately 30cm apart. For small items (e.g. tiles) spots of adhesive may be used. Wipe away excess adhesive with a damp cloth. Dried adhesive is best removed by scraping. Limitations: Not suitable for permanently wet or damp areas. Not suitable for fixing mirrors. Use Selleys Liquid Nails Mirror Metal & Glass. *Not suitable for polyethylene and polypropylene. Use Selleys All Plastic Fix. Bonds are not water-resistant. Protect bonds from water penetration if used in exterior applications. Not resistant to strong acids and strong organic solvents. Do not apply below 10°C. When used near brass or copper, the immediate area of contact will discolour to a blue tone. Handy Tips At least one surface must be porous for effective bonding. If both surfaces are non-porous, drying time is greatly increased. Clamping may be necessary until adhesive dries. Wet, damp and cold weather will increase drying time Wipe away excess with a damp rag. Use temporary supports when bonding a heavy load - support until adhesive dries. Particularly on uneven or smooth or non-porous surfaces. Good for gap filling - i.e. sticking two rough surfaces together. All Fix Big Jobs may stain slightly and colour can be paler than the surrounding area, squeeze out should be wiped off if intending to stain. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping.
$34.32
Glitz Furniture and Surface Polish Protective Shine 250g Bring dull furniture back to life with Glitz Furniture and Surface Polish. This quick spray-on polish lifts dust, reduces fingerprints, and leaves a smooth, protective shine that helps repel everyday grime. Ideal for busy homes and workspaces that want clean surfaces with a polished finish in minutes. Why you will love it Fast clean and shine: wipe away dust and light marks while restoring a bright finish. Protective layer: helps resist smears and fingerprints for surfaces that stay cleaner for longer. Versatile use: suitable for sealed timber furniture, laminates, vinyl, stainless steel, chrome, and sealed stone benchtops. Streak smart: designed to buff off clean so the surface looks fresh, not oily. Fresh finish: leaves a pleasant just cleaned feel. Best for Coffee tables, dining tables, sideboards, entertainment units Cabinet doors, shelves, desks, office furniture Appliance exteriors like stainless steel fridges and dishwashers Sealed stone and laminate benchtops How to use Shake well before use. Spray lightly onto the surface from about 20 to 25 cm, or spray onto a clean soft cloth. Wipe evenly to lift dust and light soil. Buff with a dry microfiber cloth to reveal a smooth, protective shine. Pro tips Test on a small hidden area first, especially on delicate or unusual finishes. For heavily soiled areas, clean first with a suitable surface cleaner, then polish. Use a dedicated microfiber cloth for polishing to avoid streaks. What to avoid Do not use on unsealed or raw timber. Do not use on floors, glass, fabrics, or screens. Avoid overspray near slippery walkways. Product details Brand Glitz Product Furniture and Surface Polish Protective Shine Format Aerosol spray Size 250 g Finish Smooth polished sheen Suitable Surfaces Sealed timber, laminate, vinyl, stainless steel, chrome, sealed stone benchtops Country of Use Australia Safety and storage Use in a well ventilated area and keep away from heat and open flames. Keep out of reach of children and pets. Store upright in a cool dry place. Frequently asked questions Will it make surfaces slippery It is not for floors. When used on furniture and benchtops as directed, buff to a dry finish to avoid slick residue. Can I use it on raw timber No. Seal or finish the timber first, then polish. Does it remove heavy stains It is a maintenance polish. For heavy grime, clean with an appropriate cleaner first, then apply this polish for protection and shine. Good to pair with Microfiber cleaning cloths for lint free buffing Everyday surface cleaner for pre clean on sticky or greasy areas Glues Australia keeps Australia together with trusted cleaning and care essentials. Order today for fast dispatch.
$8.21 $6.22
Strengthen critical junctions and stop leaks before they start. Crommelin Waterproofing Tape is a flexible, self-adhesive reinforcing tape designed to bridge cracks, joints, and movement-prone areas so your waterproofing membranes and sealants perform at their best. Why you will like it Reinforces weak points at wall to floor junctions, around drains, over hairline cracks, and along internal corners. Excellent adhesion to common building surfaces when used with compatible primers and membranes. Flexible backing conforms to corners and curves to maintain a continuous seal. Moisture barrier assist helps reduce the risk of water ingress beneath tiles and finishes. Easy to cut and apply for fast prep on bathrooms, balconies, laundries, and wet areas. Ideal for Showers, bathrooms, and laundries Balconies and terraces before tiling Planter boxes and upstands Penetrations such as pipes and wastes Internal corners, junctions, and small static cracks Quick specs Product Waterproofing reinforcement tape Length 5 m Finish Flexible tape for embedment into compatible membranes Typical surfaces Concrete, rendered masonry, fibre cement, primed timber, sealed gypsum, existing compatible membranes Application Hand applied, press firmly with roller or trowel How to use Prepare the area. Surface must be clean, dry, sound, and free of dust, oils, and loose material. Prime as required by your chosen waterproofing membrane system. Measure and cut lengths to suit corners, junctions, and penetrations. Pre fit to check placement. Bed the tape into the first wet coat of compatible membrane or approved adhesive. Press firmly to remove air pockets and ensure full contact. Overlap joins by at least 50 mm. At corners, mitre or fold neatly so the tape remains flat without creases that could trap water. Topcoat with additional coats of membrane to fully encapsulate the tape, observing required dry times between coats. Cure the membrane system as directed before tiling or finishing. Good to know Cover the tape with a compatible liquid membrane. Do not leave exposed to prolonged UV. Always follow the membrane manufacturer instructions for primers, coat thickness, and cure times. If in doubt about compatibility, perform a small adhesion test on your substrate and membrane. Storage and safety Store in a cool, dry place away from direct sunlight. Wear gloves and eye protection during surface prep and membrane application. Dispose of offcuts and packaging according to local regulations. What is in the box 1 roll Crommelin Waterproofing Tape, 5 m length Glues Australia helps Australians fix and protect with confidence. If you need help choosing a compatible membrane or primer for this tape, contact our team.
$39.15 $30.48
Bear PVC Duct Tape is a tough, reliable, all purpose tape that delivers a strong hold and a clean finish for quick fixes. Ideal for sealing, bundling, patching, and general repairs at home, on site, and in the workshop. Its PVC backing resists moisture and abrasion, while the high tack adhesive bonds to a wide range of surfaces for dependable results. Why you will love it Fast grab for instant hold on contact Durable PVC backing resists scuffs, tears, and everyday wear Moisture resistant for confident indoor and short term outdoor use Conformable backing wraps neatly around pipes, ducts, and irregular shapes Easy to tear by hand for quick application without tools Low residue when removed from most clean surfaces Great for Sealing HVAC duct joins and flexible ducting Temporary patching of plastic sheeting, tarps, and covers Bundling cables, mats, and lightweight components Edge protection on cartons and packing jobs Quick fixes on site and around the home Works on Metal, plastic, vinyl, painted surfaces, cardboard, glass, masonry, timber, and more. For best results, surfaces should be clean, dry, and free of dust or oils. How to use Prepare the surface by cleaning off dust, grease, and moisture. Measure and tear the required length. Scissors are optional. Apply the tape with firm pressure, smoothing from the center outward to remove air pockets. Reinforce high stress areas with overlapping strips as needed. Pro tips Apply at room temperature for the best initial tack. On porous or rough surfaces, use extra pressure or a primer for maximum bond. For long term outdoor exposure, consider overcoating edges to limit water ingress. Typical specifications Backing PVC Adhesive Rubber based Total thickness Approx. 0.16 to 0.20 mm Temperature range Approx. −10 °C to +60 °C Finish Matte PVC Common sizes 48 mm width, 30 m length and other widths as available Colour Silver or Black depending on variant Values above are typical for PVC duct tapes and may vary by batch and width. FAQs Can I use it outdoorsYes for short term jobs. For permanent outdoor sealing, select a tape rated for UV and long term weather exposure. Will it remove cleanlyOn smooth, sealed surfaces it often removes with minimal residue. Always test on an inconspicuous area first. Is it suitable for high heatPVC duct tape is best within the stated temperature range. For sustained high temperature applications, choose a foil or specialty HVAC tape. Safety Use in a well ventilated area. Press firmly during application to avoid edge lift. Keep out of reach of children. What is in the pack 1 roll of Bear PVC Duct Tape in the selected width and length Why buy from Glues Australia Trusted Australian supplier with fast dispatch Helpful support if you need sizing or product advice
$11.98 $9.27
Get a fast, permanent hold without screws, nails, or messy liquid glues. Gorilla Double Sided Tape delivers an instant tack and a strong bond on smooth and slightly rough surfaces so you can mount, fix, and create with confidence. Why you will love it Instant grab for quick, clean mounting jobs Heavy duty hold with a long lasting bond No tools needed just press to stick Works indoors and outdoors in normal Australian conditions Cleaner finish compared to visible fasteners Great for Fixing signs, hooks, cable clips, and small fixtures Mounting lightweight décor, trims, and name plates DIY repairs around the home, office, classroom, and workshop Craft projects and display boards Suitable surfaces Painted walls*, metal, sealed wood, glass, tiles, plastics, and smooth masonry. *Always test first on painted or delicate surfaces. Fresh paint must cure fully. How to use Clean both surfaces. Remove dust, oil, and moisture for best adhesion. Cut to length. Use sharp scissors or a utility knife. Apply tape to the first surface and press firmly along the full length. Peel the liner to expose the second side. Mate surfaces and press hard for 30 to 60 seconds to set the bond. Full strength develops after proper pressure. Avoid load for a short period where possible. Removal tip: lift slowly from one corner. On delicate finishes, use a plastic scraper and take care. Product details Brand Gorilla Type Double sided mounting tape Length 7.3 m Adhesive Permanent pressure sensitive Use Interior and exterior in typical household conditions Solvent free Yes Pro tips for the best hold Adhesion improves with firm pressure. Roll or press along the tape after application. For porous or chalky surfaces, seal first for a stronger bond. Cut multiple shorter strips to cover more area on larger items. Avoid contact with dust or fingers once the liner is removed. FAQ Is it removableThe bond is permanent and removal can damage delicate finishes. Test first. Will it hold in damp areasIt bonds in normal household humidity. For constantly wet or submerged applications choose a waterproof sealant or specialty tape. Shipping and returns Fast dispatch Australia wide from Glues Australia Carefully packed to protect your order Change of mind returns available if unopened and in resalable condition Always follow the instructions on the retail pack. Performance varies with surface, preparation, and load. If in doubt, test before full application.
$22.87 $17.97
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$9.49
Adhesive holder designed to hang standard trigger spray bottles securely. Space-saving vertical storage Water resistant No drilling required Examples of use: Hold glass cleaner in the kitchen Store disinfectant in the laundry Keep garden sprays in the shed
$7.88
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$17.01
Clear mini hooks sized for kitchen tools and lightweight accessories. Food-area friendly surfaces Removes cleanly Compact, clear design Examples of use: Hang measuring spoons by the stove Hold tea towels or oven mitts Store small gadgets on a splashback
$18.06
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$10.79
Wet-area rated hanging solution for towels and robes. Water-resistant adhesive Designed for bathrooms and laundries Simple, tool-free install Examples of use: Add a towel point near a vanity Place a robe hook by the shower Create a guest towel spot
$23.60
Spring-grip holder secures brooms and mops vertically to save floor space. Non-slip clamp holds 1.8 kg Adhesive mount removes cleanly Ideal for laundries and cupboards Examples of use: Hang a broom inside a pantry door Store a mop in the laundry Keep garden tools tidy in the shed
$15.53
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$11.00
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$6.76
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$7.34
Adhesive holders to support lightweight curtain rods on smooth walls. Tool-free install Damage-free removal Fits slim curtain poles Examples of use: Mount sheer curtains in rentals Create a cafe curtain over a sink Add a rod to a study nook
$15.55
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$19.97
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.
$89.23
Boyle Mosaic Craft Adhesive Glue Paste 120 g is a reliable ready to use craft adhesive paste for mosaic and small decor pieces chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 120 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Boyle Mosaic for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Boyle Mosaic Craft Adhesive Glue Paste 120 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Mounting glass tesserae and small tiles to bases Decorating frames, pots, and plaques Craft classes and school projects Suitable surfaces The adhesive works well on the following surface types when properly prepared: Terracotta and ceramic bases Primed timber Card and board Glass and stone pieces Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of workable for extended craft sessions. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial grab holds pieces in place while you continue working. Allow to dry fully before grouting or moving finished items. Temperature and environmental performance Use in dry indoor conditions for best results. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe away fresh squeeze out with a damp cloth. Wash brushes in warm soapy water. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close lid firmly after use to prevent skinning. Store at room temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$7.82
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$13.14
Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.
$12.72
Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.
$11.56
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.98
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au
$13.00
![Cabot's Wood Tone Putty Hole Filler 250g [Colour: Radiata Pine]](http://gluesaustralia.com.au/cdn/shop/files/9300611074089.jpg?v=1754724095&width=645)
![Cabot's Wood Tone Putty Hole Filler 90g [Colour: Antique Walnut]](http://gluesaustralia.com.au/cdn/shop/files/93355766.jpg?v=1754724095&width=645)
Cabot's Wood Tone Putty is ideal for filling holes, cracks and blemishes in all interior timber without shrinking. It is easy to apply and sands to a fine, smooth finish. Wood Tone Putty is compatible with water or oil based paints, stains and timber finishes. Areas All interior timber Clean Up Water Product Type Water Based
$14.71 - $18.92
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$18.48
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$28.21
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects. Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions. T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger. Key Features: All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications. Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in. Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold. Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan. Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox. Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability. Usage Applications: Home repairs, including fixing broken items and sealing leaks. Crafting and DIY projects, offering creative flexibility. Outdoor applications, including camping gear repairs. Professional job site tasks, providing reliability and strength. Why Choose T-Rex® Tape? When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project. In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
$16.48
Tarzan's Grip Mounting Tape is a double sided, heavy duty, high strength tape that instantly grabs for easy, fast and permanent mounting. It is ideal for a multitude of surfaces, including metal, wood, rubber, leather, china, brick, stone, plasterboard and most plastics. Extremely strong Instant grab Solvent free Permanent
$12.42
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$108.41
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
Instant set, high viscosity, multipurpose super glue Suitable for bonding substrates with irregular surfaces and in vertical applications Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, fabrics, wood, paper and other materials Can be used on porous substrates such as porcelain and china Small repairs to glasses, bonded shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Surfaces with small irregularities max. 0.5 mm On vertical surfaces Characteristics and Advantages One Component Easy to apply, non-sag, gel consistency Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper, card Low consumption adhesive Versatile, allows adhesion between different materials Colourless Durable Packaging 3 g Tube
$12.00
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
![Sika Sikaflex 118 Extreme Grab 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use. Very high initial grab Fixing of heavy objects without temporary fixation Good workability Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors* Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking Packaging 290 ml cartridge, 12 cartridges per box Colour White Composition Silane terminated polymer Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging. Density ~1.40 kg/l Technical Information Shore A hardness ~50 (after 28 d) Tensile strength ~2.2 N/mm2 Tear propagation resistance ~10.0 N/mm Service temperature −40 °C min. / +80 °C max. SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive. For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush. Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours). For more detailed advice and instructions contact Sika Technical Services. Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically. For cleaning skin use Sika® Hand Wipes.
$25.60
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$21.47
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$16.13
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$88.91
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$15.46
Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages Fast curing. Will not damage plastic shower liners. Panels can be relocated for up to 30 minutes after positioning. Excellent adhesion to most common building materials. Easy to apply and clean up. Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining. Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive. Brace the lining as required in the shower manufacturer's installation instructions. Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.
$19.07
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$8.21
You have seen 144 out of 689 products
Find products tagged for use on wood. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on wood surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
