Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.
$73.08
Selleys Araldite Rapid Epoxy Adhesive 14 mL Fast-setting, two-part epoxy for quick, durable repairs at home, in the workshop, or on site. The self-mixing syringe makes application clean and precise, setting in about 90 seconds and reaching handling strength soon after. Dries translucent for a neat finish. Key benefits Sets in approximately 90 seconds for rapid fixes High strength bond up to 75 kg/cm² when fully cured Dries translucent for low-visibility repairs Self-mixing nozzle for easy, accurate application Versatile bonding across common materials Best for Everyday repairs and small assemblies Fixing chipped ceramics and china Metal, glass, leather, rubber, and many plastics Suitable materials China, metal, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. How to use Prep Abrade, clean, and dry both surfaces. Attach nozzle Remove cap, fit and lock the self-mixing nozzle, then purge a small amount until evenly mixed. Apply Spread adhesive on both surfaces and join within 1 minute. Hold Support the bond for about 10 minutes to prevent movement. Cure Maximum strength develops after about 16 hours. Allow longer in cold conditions. Clean up Wipe away uncured adhesive with acetone. Remove and dispose of the used mixing nozzle before the adhesive sets in the tip. Technical details Technology Two-part epoxy Set time About 90 seconds Handling time Approximately 10 minutes Full cure About 16 hours Colour when dry Translucent Temperature resistance Up to 60 °C Pack size 14 mL self-mixing syringe Good to know Bond may soften above 60 °C and regains strength when cooled. Pre-test on leather and rubber to confirm suitability. May discolor with prolonged UV exposure. Store in a cool, dry place. Replace cap after removing the used nozzle. Safety Follow the safety directions on the packaging. Use in a well-ventilated area and avoid skin contact. Keep out of reach of children.
$19.26
Tuff Turf Synthetic Grass Adhesive 320 g Overview Tuff Turf Synthetic Grass Adhesive 320 g is a high quality synthetic grass adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials synthetic turf backing seaming tape concrete compacted base plywood Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Install in dry conditions between 10°C and 30°C, avoiding heavy dew or rain. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Working time varies with conditions. Allow sufficient cure before foot traffic. Full strength typically within 24 to 48 hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean tools while wet with a suitable solvent or soapy water depending on formulation. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$13.40
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$13.39
Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.
$11.56
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$35.34 - $39.95
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects. Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions. T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger. Key Features: All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications. Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in. Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold. Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan. Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox. Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability. Usage Applications: Home repairs, including fixing broken items and sealing leaks. Crafting and DIY projects, offering creative flexibility. Outdoor applications, including camping gear repairs. Professional job site tasks, providing reliability and strength. Why Choose T-Rex® Tape? When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project. In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
$16.48
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Longer work time (10 minutes)
$23.70
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
SikaSeal® Super-200 is great for sealing of connection joints with moderate movement Good UV resistance Low odour For exterior and interior use USE Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling Filling of cracks on interior and exterior walls (with no permanent water immersion) CHARACTERISTICS AND ADVANTAGES For exterior and interior use High movement capability ±12.5% Good UV resistance Solvent-free, low odour Overpaintable Very good adhesion on most construction materials such as concrete, plaster, wood Possible storage at -10°C for short period of time (max 24h) Conforms to EN 15651-1 F INT EXT
$9.36
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](http://gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic
$5.82
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.98
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
![Sika Sikaflex 118 Extreme Grab 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use. Very high initial grab Fixing of heavy objects without temporary fixation Good workability Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors* Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking Packaging 290 ml cartridge, 12 cartridges per box Colour White Composition Silane terminated polymer Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging. Density ~1.40 kg/l Technical Information Shore A hardness ~50 (after 28 d) Tensile strength ~2.2 N/mm2 Tear propagation resistance ~10.0 N/mm Service temperature −40 °C min. / +80 °C max. SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive. For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush. Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours). For more detailed advice and instructions contact Sika Technical Services. Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically. For cleaning skin use Sika® Hand Wipes.
$31.22
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$21.47
Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages Fast curing. Will not damage plastic shower liners. Panels can be relocated for up to 30 minutes after positioning. Excellent adhesion to most common building materials. Easy to apply and clean up. Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining. Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive. Brace the lining as required in the shower manufacturer's installation instructions. Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.
$21.37
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application. Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Wallboard Wood Masonry Plaster Primed nail heads Plasterboard Colours White Technology Water Based Use Interior Exterior (when painted) How To Use Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications). Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions. Handy Tips Painting with oil-based paints is not recommended until 24 hours after filler has been applied. Water based paints may be used immediately after filler has set. If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping or sanding.
$25.02
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$7.19
![Selleys No More Gaps Exterior & Weatherboard 430g [White]](http://gluesaustralia.com.au/cdn/shop/files/8a8dbfbe2151431e9a3365cd49a9be75.jpg?v=1757753104&width=645)
Selleys No More Gaps Exterior & Weatherboard is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. Has good resistance to weathering Contains a titanium compound for superior UV resistance. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application).. Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack. Is formulated for long term resistance to cracking and crumbling. Is water based, so can be cleaned up with water. Will not stain building materials. Where can this product be used? Between exterior window and door frames Fascia boards and eaves Masonry Walls Tiling Timber & synthetic weatherboards Brickwork Fences Where shrinkage or movement has caused rigid fillers to crack Gaps with a maximum width of 25mm & depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Fibre cement sheeting, plasterboard Masonry Ceramic Tiles Glass Aluminium & other metals Many other building surfaces
$17.87
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$10.55
Selleys Liquid Nails Exterior: The Builder's Choice for Durable Outdoor Bonds Key Features Adheres up to 3 tonnes per m² after just 4 hours on timber Water, heat, and UV-resistant Long-lasting bond that won't crack or go brittle Fast and easy water clean-up Compliant with Australian Standard AS 2329(1999) and Green Building Council VOC limits Suitable Materials This adhesive is ideal for the following materials: Timber Plasterboard MDF LOSP Treated Timber Concrete Masonry Plastics (pre-test for compatibility) Tiles Glass Ceramics Directions for Use Follow these simple steps for optimal performance: Ensure surfaces are clean and free from grease or loose particles. Cut cartridge tip, fit nozzle, and cut to 5mm opening. Apply adhesive along the material's length or in beads on flat surfaces. Press pieces firmly together, securing with fasteners or clamps. Allow to set for a minimum of 4 hours before removing any temporary fasteners. Limitations Not suitable for use on PFTE, PE, or PP. Cleaning & Safety Clean up is easy with warm soapy water or a damp cloth for wet adhesive, and a scraper or sandpaper for dried adhesive. Product Specifications Available in 350g cartridges, in white color, and uses Self-crosslinking acrylic technology.
$12.00
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
Features Simply sticks almost anything without screws or clamps* Instantly holds even on vertical surfaces* Adjustable for up to 15 minutes UV & water-resistant Holds up to 360kg/ m² Where can this product be used? Indoors and outdoors for any bonding applications What materials is this product suitable for? Glass Metals Timber Brick Concrete / masonry Tiles Not for polyethylene, polypropylene or teflon Colours White Technology Sil-X® Use Interior Exterior How to use Make sure surfaces are clean, free from grease, girt and grime. Sand back any loose or peeling surfaces. Pull off cap, unscrew nozzle and pierce membrane with the tip of the nozzle. Replace nozzle and cut along the second ridge. Cover one surface in the adhesive in long vertical strips. After applying the adhesive, press surfaces together firmly, ensuring the adhesive spreads. Clean up any excess product with methylated spirits.
$17.58
$52.00
Selleys All Clear Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for: Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Application & Safety Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. How to Apply The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam Additional Information *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C.
$13.59
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$26.95
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$13.53
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
Interior and exterior use Acetic cure Excellent bond to glass Parfix Window & Glass Silicone is suitable for use on windows, glass partitions and glass blocks. Ideal for both interior and exterior use, Parfix Window & Glass Silicone is an acetic cure silicone with that bonds securely to glass, providing a water tight and UV resistant seal.
$11.57
Parfix super glue is a fast setting cyanoacrylate-based adhesive that dries clear with a strong bond Instant strong bond Sets in 10 seconds Dries clear
$3.41
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$9.35
Parfix Fast Grip is a solvent-based contact adhesive that is heat and water-resistant, making it suitable for use in kitchens and bathrooms. Immediate strong bond Heat and water resistant Brush application
$21.22
The Loctite Super Glue Creative Pen offers the ultimate solution for precise, fast, and reliable bonding. Its ergonomic pen design ensures a controlled application, perfect for intricate tasks like crafting, DIY projects, or quick household repairs. The pen tip provides pinpoint accuracy, so you can apply just the right amount of glue, reducing mess and waste. Loctite’s fast-drying formula creates a strong bond on materials such as wood, plastic, metal, ceramic, and leather, making it versatile for any project. Whether you're fixing a broken ornament, assembling models, or working on craft projects with the kids, Loctite Super Glue Creative Pen guarantees a professional finish every time. LOCTITE® Super Glue Creative Pen Precision bonding on wood, metal, plastic, rubber, and more. Waterproof, weather-resistant, and shock-resistant. Equipped with a long nozzle and easy-grip squeeze bottle for fast and accurate application. Characteristics: LOCTITE® Super Glue Creative Pen is a one-part instant gel adhesive in a convenient dispenser, perfect for home use. It forms strong bonds between a wide range of common materials, including plastics, rubbers, metals, wood, ceramics, leather, fabrics, cardboard, and paper. Its non-drip formula allows for use on vertical or overhead surfaces. The ergonomic pack design ensures precise application, ideal for bonding smaller items. Bonding Speed: Initial adhesion in 5 to 30 seconds, depending on the substrate. Bond Strength (ISO 4587): 10 to 20 N/mm² (tensile shear) in 12 to 24 hours, depending on the substrate. Water-resistant to EN204-D3 standard. Ceramic bonds can withstand over 50 dishwasher cycles under controlled laboratory conditions. Instructions for Use: Ensure all surfaces to be bonded are clean, dry, and fit closely. Twist the cap clockwise onto the pack until you hear a clicking sound. Do not overtighten; a three-quarter turn is sufficient. Avoid skin contact with the glue. Gently squeeze the rubber panels and apply a minimal amount of adhesive to one surface. Press parts together immediately and hold with hand pressure for at least 1 minute. Allow the bond to set undisturbed for 10 minutes, or preferably overnight, to achieve full bond strength. Protect work surfaces and avoid spills. Remove cured glue with LOCTITE® Glue Remover. For best results, apply at room temperature (15-30°C) with at least 30% relative humidity. After use, wipe the nozzle clean with a tissue, replace the cap, and store in a cool, dry place. Technical Data: Composition: Ethyl cyanoacrylate Appearance: Clear gel Density: 1.1 g/cm³ @ 20°C Viscosity: Gel Safety: Refer to SDS 2669372 Shelf Life: 30 months unopened (stored at 2-8°C) Limitations: Do not use on dusty, dirty, or wet surfaces. Not suitable for bonding polypropylene, polyethylene, PTFE, silicone rubber, glass, glazed surfaces, very soft leather, or foams. Do not use for bonding items exposed to hot liquids or high temperatures for extended periods. Optimum performance is achieved in dry conditions. Storage: Store in a cool, dry place, out of reach of children. Why choose Glues Australia? We provide premium-quality adhesives like Loctite, backed by our exceptional customer service. With fast, reliable delivery across Australia, you’ll get the products you need when you need them. Shop confidently with Glues Australia, your trusted adhesive supplier!
$11.57
Introducing Gorilla Clear Grip® - Your Ultimate Adhesive Solution! Are you tired of struggling with weak bonds that don't stand the test of time? Say goodbye to ordinary adhesives and embrace the power of Gorilla Clear Grip® - the flexible, fast-setting, and crystal clear contact adhesive that creates an unbreakable bond! Unleash your creativity with Gorilla Clear Grip®! Whether you're building, repairing, or crafting, this heavy-duty adhesive is your go-to companion. Its no-run formula ensures a clean and easy application, while the fast grab feature holds your project in place within seconds, saving you precious time and effort. Worried about the unpredictable weather? Fear not! Gorilla Clear Grip® is fully waterproof, making it ideal for both indoor and outdoor projects. Rain or shine, your creations will stay intact and look flawless for years to come. What sets Gorilla Clear Grip® apart is its remarkable versatility. It forms a permanent bond on a wide range of materials, including metal, glass, fabric, wood, ceramic, leather, paper, plastic, and more. With Gorilla Clear Grip®, you can confidently tackle any project, big or small. Concerned about safety? Worry not! Gorilla Clear Grip® is photo-safe and washer/dryer safe, ensuring that your precious memories and fabrics remain unharmed during the bonding process. Using Gorilla Clear Grip® is a breeze! Just ensure that the surfaces are clean and apply the adhesive to each surface to be bonded. For maximum bond strength, wait a couple of minutes for the adhesive to partially dry before joining the surfaces. The bond forms immediately, ensuring a strong connection. Store your Gorilla Clear Grip® in a cool, dry location after each use, away from children and animals. The flammable adhesive requires extra care, so keep it away from heat, sparks, flames, or smoking. For easy re-opening, apply a thin coat of petroleum jelly to the threads before replacing the cap. Frequently Asked Questions: Q: What surfaces does Gorilla Clear Grip® adhere to? A: Gorilla Clear Grip® adheres to a wide variety of surfaces, including wood, metal, stone, ceramic, glass, plastic, PVC, brick, concrete, foam, paper, rubber, fabric, and laminate. However, it is not recommended for use on polystyrene, polypropylene, or polyethylene products, and it should not be used around food. Q: How do you clean up Gorilla Clear Grip®? A: To clean uncured adhesive, wipe it with a dry cloth and then use acetone, isopropyl alcohol, or citrus-based solvents according to the manufacturer's instructions. Cured adhesive can be removed by scraping it from the surface. Q: Is Gorilla Clear Grip® UV resistant? A: Yes, it is UV resistant, making it ideal for outdoor applications. Experience the Gorilla Clear Grip® difference today! Unleash your creativity, achieve impeccable results, and make your projects stand the test of time. Join the countless satisfied customers who have discovered the power of Gorilla Clear Grip®. Build, Repair, Craft™ with confidence!
$20.51
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 9.1m x 48mm [White]](http://gluesaustralia.com.au/cdn/shop/files/052427601001N_6bf5df2b-2379-4b95-849b-de69b5185a52.jpg?v=1754712477&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$14.99
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 27.4m x 48mm [White]](http://gluesaustralia.com.au/cdn/shop/files/052427840585N_07d2cff7-275f-4461-91ba-a3bace52b8c5.jpg?v=1754712482&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$29.62
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$26.68
Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, and holds up to 6.8kg! (15 pounds) Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features 6.8KG Strong Hold - Sticks to smooth and rough surfaces.* Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How much weight will Gorilla Mounting Tape hold? Gorilla Black Mounting Tape will hold up to 30 (13.6KG) pounds per project. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface. If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur. If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.
$17.95
Attach items to paper, wood, cloth, pottery, and more with the non-toxic adhesive of Elmer's Washable School Glue. Specially formulated to be washable and easy to use, Elmer's School Glue perfect for school projects and home arts and crafts. Elmer’s School Glue is adjustable before setting and does not run, delivering reliable results with every use. You can also use your liquid glue to create glue slime! Four 5-ounce bottle of Elmer's Clear Washable School Glue. How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$4.79
Dunlop Revive & Shine Dunlop Revive & Shine is a neutral, multipurpose cleaner and maintainer that enhances the appearance of sealed floors. Designed for use on timber, vinyl, and laminate floors, this product reduces the appearance of scuffing, increases durability, and improves gloss levels. For best results, use monthly to keep your floors looking their best. Key Benefits: Cleans and maintains timber, vinyl, and laminate flooring Provides extra durability, wear resistance, and shine Increases slip resistance Reduces the appearance of scuffing Ideal for monthly maintenance Suitable For Use On: Timber, vinyl, and laminate flooring Surface Type: Floors Location: Indoor Colour & Sizes: Colour: Milky (Dries Clear) Size: 500ml Item Code: 19882 Directions for Use: Dilution: Mix 20mL of Dunlop Revive & Shine per 1L of warm water in a bucket. Cleaning: Mop the floor with the solution. Spills: For spills, hose down the area and wash with large amounts of water. Note: The use of Personal Protective Equipment is recommended during application. Dunlop Revive & Shine is perfect for keeping your timber, vinyl, and laminate floors looking like new, providing enhanced shine, durability, and slip resistance.
$21.46
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent-free and non-toxic. Bostik Glu Dots are also available in an extra strength version, for permanent applications. Ket Features: -Repositionable -Transparent, non-visible -Solvent-free and non-toxic -Acid and lingin free, suitable for photographs Description Bostik Extra Strength Glu Dots are little circles of double-sided, clear adhesive which exhibit high tack, offering secure bonds to almost anything including paper, wood, plastic, metal, glass and painted surfaces. These non-yellowing dots are designed to provide a permanent hold and the bond strength will increase over time. They are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent free and non-toxic. Bostik Glu Dots are also available in a REMOVABLE version, for non-permanent applications. Applications - Holding up posters, cards, certificates, notices, maps, menus, calendars, messages, timetables, learning aids, children paintings, decorations, etc. - Keeping in place telephones, mouse pads, pens, candles, figurines, vases, calculators, ornaments, etc. - Keeping picture frames straight. - Sticking photos in an album. - Ideal for school projects, scrapbooking, art and craft projects. Adhesion Bostik Extra Strength Glu Dots Stick extremely well to non-porous surfaces such as metal, glass, plastics, vinyl coated and painted surfaces and porous surfaces such as paper, boards, cloth, and wood. Limitations - Not suitable for highly absorbent, damp or dusty surfaces. - Not suitable for holding up heavy objects. - May damage delicate papers on removal. Safety Instructions Bostik Extra Strength Glu Dots is non-toxic. The product poses a choking hazard if ingested. In the event of ingestion, the mouth should be washed with water. Seek medical assistance if irritation or discomfort persists. Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions. Surface Preparation Ensure that surfaces are clean, dry and free of any dust, grease and loose materials. How to use 1. Tear along the perforations. 2. Peel off the paper backing. 3. Press the dot firmly onto the first surface. 4. Remove the clear film. 5. Press the second surface firmly onto the dot.
$7.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$18.70
Glitz Furniture and Surface Polish Protective Shine 250g Bring dull furniture back to life with Glitz Furniture and Surface Polish. This quick spray-on polish lifts dust, reduces fingerprints, and leaves a smooth, protective shine that helps repel everyday grime. Ideal for busy homes and workspaces that want clean surfaces with a polished finish in minutes. Why you will love it Fast clean and shine: wipe away dust and light marks while restoring a bright finish. Protective layer: helps resist smears and fingerprints for surfaces that stay cleaner for longer. Versatile use: suitable for sealed timber furniture, laminates, vinyl, stainless steel, chrome, and sealed stone benchtops. Streak smart: designed to buff off clean so the surface looks fresh, not oily. Fresh finish: leaves a pleasant just cleaned feel. Best for Coffee tables, dining tables, sideboards, entertainment units Cabinet doors, shelves, desks, office furniture Appliance exteriors like stainless steel fridges and dishwashers Sealed stone and laminate benchtops How to use Shake well before use. Spray lightly onto the surface from about 20 to 25 cm, or spray onto a clean soft cloth. Wipe evenly to lift dust and light soil. Buff with a dry microfiber cloth to reveal a smooth, protective shine. Pro tips Test on a small hidden area first, especially on delicate or unusual finishes. For heavily soiled areas, clean first with a suitable surface cleaner, then polish. Use a dedicated microfiber cloth for polishing to avoid streaks. What to avoid Do not use on unsealed or raw timber. Do not use on floors, glass, fabrics, or screens. Avoid overspray near slippery walkways. Product details Brand Glitz Product Furniture and Surface Polish Protective Shine Format Aerosol spray Size 250 g Finish Smooth polished sheen Suitable Surfaces Sealed timber, laminate, vinyl, stainless steel, chrome, sealed stone benchtops Country of Use Australia Safety and storage Use in a well ventilated area and keep away from heat and open flames. Keep out of reach of children and pets. Store upright in a cool dry place. Frequently asked questions Will it make surfaces slippery It is not for floors. When used on furniture and benchtops as directed, buff to a dry finish to avoid slick residue. Can I use it on raw timber No. Seal or finish the timber first, then polish. Does it remove heavy stains It is a maintenance polish. For heavy grime, clean with an appropriate cleaner first, then apply this polish for protection and shine. Good to pair with Microfiber cleaning cloths for lint free buffing Everyday surface cleaner for pre clean on sticky or greasy areas Glues Australia keeps Australia together with trusted cleaning and care essentials. Order today for fast dispatch.
$8.21 $6.22
Strengthen critical junctions and stop leaks before they start. Crommelin Waterproofing Tape is a flexible, self-adhesive reinforcing tape designed to bridge cracks, joints, and movement-prone areas so your waterproofing membranes and sealants perform at their best. Why you will like it Reinforces weak points at wall to floor junctions, around drains, over hairline cracks, and along internal corners. Excellent adhesion to common building surfaces when used with compatible primers and membranes. Flexible backing conforms to corners and curves to maintain a continuous seal. Moisture barrier assist helps reduce the risk of water ingress beneath tiles and finishes. Easy to cut and apply for fast prep on bathrooms, balconies, laundries, and wet areas. Ideal for Showers, bathrooms, and laundries Balconies and terraces before tiling Planter boxes and upstands Penetrations such as pipes and wastes Internal corners, junctions, and small static cracks Quick specs Product Waterproofing reinforcement tape Length 5 m Finish Flexible tape for embedment into compatible membranes Typical surfaces Concrete, rendered masonry, fibre cement, primed timber, sealed gypsum, existing compatible membranes Application Hand applied, press firmly with roller or trowel How to use Prepare the area. Surface must be clean, dry, sound, and free of dust, oils, and loose material. Prime as required by your chosen waterproofing membrane system. Measure and cut lengths to suit corners, junctions, and penetrations. Pre fit to check placement. Bed the tape into the first wet coat of compatible membrane or approved adhesive. Press firmly to remove air pockets and ensure full contact. Overlap joins by at least 50 mm. At corners, mitre or fold neatly so the tape remains flat without creases that could trap water. Topcoat with additional coats of membrane to fully encapsulate the tape, observing required dry times between coats. Cure the membrane system as directed before tiling or finishing. Good to know Cover the tape with a compatible liquid membrane. Do not leave exposed to prolonged UV. Always follow the membrane manufacturer instructions for primers, coat thickness, and cure times. If in doubt about compatibility, perform a small adhesion test on your substrate and membrane. Storage and safety Store in a cool, dry place away from direct sunlight. Wear gloves and eye protection during surface prep and membrane application. Dispose of offcuts and packaging according to local regulations. What is in the box 1 roll Crommelin Waterproofing Tape, 5 m length Glues Australia helps Australians fix and protect with confidence. If you need help choosing a compatible membrane or primer for this tape, contact our team.
$39.15 $30.48
Bear PVC Duct Tape is a tough, reliable, all purpose tape that delivers a strong hold and a clean finish for quick fixes. Ideal for sealing, bundling, patching, and general repairs at home, on site, and in the workshop. Its PVC backing resists moisture and abrasion, while the high tack adhesive bonds to a wide range of surfaces for dependable results. Why you will love it Fast grab for instant hold on contact Durable PVC backing resists scuffs, tears, and everyday wear Moisture resistant for confident indoor and short term outdoor use Conformable backing wraps neatly around pipes, ducts, and irregular shapes Easy to tear by hand for quick application without tools Low residue when removed from most clean surfaces Great for Sealing HVAC duct joins and flexible ducting Temporary patching of plastic sheeting, tarps, and covers Bundling cables, mats, and lightweight components Edge protection on cartons and packing jobs Quick fixes on site and around the home Works on Metal, plastic, vinyl, painted surfaces, cardboard, glass, masonry, timber, and more. For best results, surfaces should be clean, dry, and free of dust or oils. How to use Prepare the surface by cleaning off dust, grease, and moisture. Measure and tear the required length. Scissors are optional. Apply the tape with firm pressure, smoothing from the center outward to remove air pockets. Reinforce high stress areas with overlapping strips as needed. Pro tips Apply at room temperature for the best initial tack. On porous or rough surfaces, use extra pressure or a primer for maximum bond. For long term outdoor exposure, consider overcoating edges to limit water ingress. Typical specifications Backing PVC Adhesive Rubber based Total thickness Approx. 0.16 to 0.20 mm Temperature range Approx. −10 °C to +60 °C Finish Matte PVC Common sizes 48 mm width, 30 m length and other widths as available Colour Silver or Black depending on variant Values above are typical for PVC duct tapes and may vary by batch and width. FAQs Can I use it outdoorsYes for short term jobs. For permanent outdoor sealing, select a tape rated for UV and long term weather exposure. Will it remove cleanlyOn smooth, sealed surfaces it often removes with minimal residue. Always test on an inconspicuous area first. Is it suitable for high heatPVC duct tape is best within the stated temperature range. For sustained high temperature applications, choose a foil or specialty HVAC tape. Safety Use in a well ventilated area. Press firmly during application to avoid edge lift. Keep out of reach of children. What is in the pack 1 roll of Bear PVC Duct Tape in the selected width and length Why buy from Glues Australia Trusted Australian supplier with fast dispatch Helpful support if you need sizing or product advice
$11.98 $9.27
Get a fast, permanent hold without screws, nails, or messy liquid glues. Gorilla Double Sided Tape delivers an instant tack and a strong bond on smooth and slightly rough surfaces so you can mount, fix, and create with confidence. Why you will love it Instant grab for quick, clean mounting jobs Heavy duty hold with a long lasting bond No tools needed just press to stick Works indoors and outdoors in normal Australian conditions Cleaner finish compared to visible fasteners Great for Fixing signs, hooks, cable clips, and small fixtures Mounting lightweight décor, trims, and name plates DIY repairs around the home, office, classroom, and workshop Craft projects and display boards Suitable surfaces Painted walls*, metal, sealed wood, glass, tiles, plastics, and smooth masonry. *Always test first on painted or delicate surfaces. Fresh paint must cure fully. How to use Clean both surfaces. Remove dust, oil, and moisture for best adhesion. Cut to length. Use sharp scissors or a utility knife. Apply tape to the first surface and press firmly along the full length. Peel the liner to expose the second side. Mate surfaces and press hard for 30 to 60 seconds to set the bond. Full strength develops after proper pressure. Avoid load for a short period where possible. Removal tip: lift slowly from one corner. On delicate finishes, use a plastic scraper and take care. Product details Brand Gorilla Type Double sided mounting tape Length 7.3 m Adhesive Permanent pressure sensitive Use Interior and exterior in typical household conditions Solvent free Yes Pro tips for the best hold Adhesion improves with firm pressure. Roll or press along the tape after application. For porous or chalky surfaces, seal first for a stronger bond. Cut multiple shorter strips to cover more area on larger items. Avoid contact with dust or fingers once the liner is removed. FAQ Is it removableThe bond is permanent and removal can damage delicate finishes. Test first. Will it hold in damp areasIt bonds in normal household humidity. For constantly wet or submerged applications choose a waterproof sealant or specialty tape. Shipping and returns Fast dispatch Australia wide from Glues Australia Carefully packed to protect your order Change of mind returns available if unopened and in resalable condition Always follow the instructions on the retail pack. Performance varies with surface, preparation, and load. If in doubt, test before full application.
$22.87 $17.97
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$9.49
Wet-area rated hanging solution for towels and robes. Water-resistant adhesive Designed for bathrooms and laundries Simple, tool-free install Examples of use: Add a towel point near a vanity Place a robe hook by the shower Create a guest towel spot
$8.81
You have seen 144 out of 718 products
Find products tagged for use on wood. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on wood surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
