PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$8.28
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$19.95
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$8.12
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$185.00
Directions: Spray affected area Allow penetrating for 5 to 10 minutes with a damp cloth Wipe over Allow drying Uses: Household, motor vehicles, boating & office carpets
$7.00
Directions: Spray affected area Allow penetrating for 5 to 10 minutes with a damp cloth Wipe over Allow drying Uses: Household, motor vehicles, boating & office carpets
$4.00
A blend of nut and citrus oils specially formulated to create a drying oil to maintain and rejuvenate wooden items that come into regular contact with food or water which can cause the timber to swell and dry out. Simple wipe on and wipe off application to make timber look & feel nourished. Maintain wood items that come in contact with food & water. Ideal for wooden chopping boards, serving bowls and utensils. 250mL Simple wipe on and wipe off with a rag
$16.88
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$14.76
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$8.89
Loctite Super Glue Longneck Bottle features a precision tip which allows controlled application without dripping, thus less mess. It has an easy-open cap with a metal pin that cleans and seals the nozzle for a clog-free performance. The long nozzle is ideal for gluing hard to reach surfaces. The ''finger friendly'' bottle keeps fingers glue free, as well as allows for a continuous flow or a precise drop of glue. It bonds a variety of materials including leather, ceramic, rubber, paper, metal, china, wood and most plastics. Loctite Super Glue Longneck Bottle dries clear and sets without clamping. Loctite Super Glue Longneck Bottle is resistant to moisture, most chemicals and freezing temperatures. Recommended For Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings Not Recommended For Use in dishwasher, oven or microwave Use on repairs needing high flexibility Glazed surfaces Exterior Applications Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene Safety Precautions Apply in a well-ventilated area. Wear gloves and wash hands after use. Preparation Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup Cured adhesive may be cut away with caution using a sharp blade, acetone or with boiling water.
$8.44
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$18.13
Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$18.73
GORILLA SUPER GLUE GEL Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. PRODUCT FEATURES NO RUN CONTROL GEL FORMULA ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use. IMPACT TOUGH: Increase impact resistance and strength FAST-SETTING: Dries in 10-45 seconds, no clamping required VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more! *Not recommended for use on polyethylene or polypropylene plastic or similar materials. DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Prepare Gorilla Super Glue Gel With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle. Apply Gorilla Super Glue Gel Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. Secure Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure. TECHNICAL SPECS APPLICATION TEMPERATURE – Room temperature SERVICE TEMPERATURE – -53.9°C to 104.4°C OUTDOOR – No PAINTABLE – No SANDABLE – Yes STAINABLE – No EXPANDS WHEN CURED – No CURED COLOR – Clear STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator GAP FILLING – No FAQS Why isn’t my bottle of Gorilla Super Glue filled to the top? For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle. How is Gorilla Super Glue different than Gorilla Glue? Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed. What does Impact Tough mean? Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond. Will Gorilla Super Glue bond plastic/vinyl/rubber? Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds. How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin? To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal. How do I remove Gorilla Super Glue from my surface? To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first. Is Gorilla Super Glue food safe? Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation. What should I do if I think a human or animal ingested Gorilla Super Glue? Additional product safety and first aid information can be found here. How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue? Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key. Why do I need to shake and tap the bottle? Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
$10.04
GORILLA SUPER GLUE GEL Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. PRODUCT FEATURES NO RUN CONTROL GEL FORMULA ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use. IMPACT TOUGH: Increase impact resistance and strength FAST-SETTING: Dries in 10-45 seconds, no clamping required VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more! *Not recommended for use on polyethylene or polypropylene plastic or similar materials. DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Prepare Gorilla Super Glue Gel With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle. Apply Gorilla Super Glue Gel Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. Secure Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure. TECHNICAL SPECS APPLICATION TEMPERATURE – Room temperature SERVICE TEMPERATURE – -53.9°C to 104.4°C OUTDOOR – No PAINTABLE – No SANDABLE – Yes STAINABLE – No EXPANDS WHEN CURED – No CURED COLOR – Clear STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator GAP FILLING – No FAQS Why isn’t my bottle of Gorilla Super Glue filled to the top? For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle. How is Gorilla Super Glue different than Gorilla Glue? Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed. What does Impact Tough mean? Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond. Will Gorilla Super Glue bond plastic/vinyl/rubber? Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds. How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin? To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal. How do I remove Gorilla Super Glue from my surface? To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first. Is Gorilla Super Glue food safe? Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation. What should I do if I think a human or animal ingested Gorilla Super Glue? Additional product safety and first aid information can be found here. How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue? Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key. Why do I need to shake and tap the bottle? Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
$14.99
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$9.53
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$48.79
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$77.97
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0fda3f36-74b9-4f76-87c5-eecf1c56afcc.jpg?v=1754715680&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_3922d4f4-2f1d-4263-a2de-14b767df10ba.jpg?v=1754715681&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e4f50d8f-e0a6-4255-a242-9c3e7590f0f3.jpg?v=1754715675&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e401b93c-d8cb-46ff-be50-3f30c2495024.jpg?v=1754715675&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_84aa9bc6-f55e-40c0-afbe-820db6fddb04.jpg?v=1754715673&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0c7f6c0e-695e-4545-a57c-1e5bf7ca1f0c.jpg?v=1754715673&width=645)
$9.49
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$26.80
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$18.30
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
Selleys Rapid Mould Killer is a fast-acting spray that tackles stubborn mould and mildew in and around the home. Formulated for busy bathrooms, laundries and other damp, mould-prone areas, it gets to work almost immediately, destroying visible mould in as little as 30 seconds and eliminating 99.9% of germs on treated surfaces. The 750ml trigger pack delivers plenty of product for larger jobs, with a twist nozzle that switches between a fine spray and a targeted stream. Key features Effectively eradicates stubborn mould and mildew Fast acting – destroys visible mould in around 30 seconds Eliminates 99.9% of germs on hard surfaces Adjustable spray/stream trigger nozzle for controlled application Generous 750ml size for larger and more frequent jobs Where to use it Indoors: Ideal throughout the bathroom and laundry – on tiles and grout, shower screens, shower curtains, toilets, rubber bath mats, plastic surfaces and other mould-affected areas. Outdoors: Suitable for spot-treating mould-affected exterior surfaces where staining and mould have taken hold. How to use Twist the nozzle to either SPRAY or STREAM. Spot test on an inconspicuous area first. Spray directly onto the mould-affected surface. Leave for about 30 seconds, then rinse, wipe or scrub off. Important notes On some matt-finish tiles or in hard-water areas, staining may occur – always patch test first. Not suitable for fabric, mirror tiles, metallic surfaces, or older baths and basins. Do not mix with other cleaners. Specifications Brand Selleys Product Rapid Mould Killer Size 750ml Format Ready-to-use trigger spray Action Destroys mould in ~30 seconds; kills 99.9% of germs Best for Bathrooms, laundries, toilets and other mould-prone areas Suitable surfaces Tiles, grout, shower screens, shower curtains, plastic, rubber bath mats Safety This is a bleach-based (sodium hypochlorite) mould killer. Use in a well-ventilated area and wear suitable gloves and eye protection. Avoid contact with skin, eyes and clothing. Never mix with other cleaning products or acids, as hazardous chlorine gas can be released. Keep out of reach of children, rinse treated surfaces after use, and store upright in a cool place away from direct sunlight. Always read the label and refer to the manufacturer’s Safety Data Sheet before use.
$10.79
Selleys BBQ Tough Grease & Grime Cleaner is a fast-acting spray made for the quick clean-up that keeps a barbecue in good shape. It lifts cooking grease, baked-on food and general grime from hotplates and grills so the cooking surface stays clean and hygienic, without the hard scrubbing a wire brush needs. The 500mL trigger bottle sprays an even coat straight onto the surface and is ready to use with no mixing or dilution. Formula overview The cleaner uses a surfactant-based, non-caustic formula, so it powers through fat and oily build-up while being easier to handle than harsh caustic products. It goes to work in two to three minutes, loosening the grease so it wipes away instead of needing to be scoured off. Because it is water based, any residue rinses and wipes off easily with a damp cloth. Where to use it Outdoors: BBQ hotplates, grills and racks are the main job, ideal as an after-cook clean while the plate is still slightly warm. It also works well on outdoor furniture and many other outdoor surfaces where grease and grime gather. Indoors: the same grease-cutting action can help on other greasy cooking-area surfaces, as long as they are not on the unsuitable list below. The product is formulated first and foremost for barbecue and exterior clean-up. How to use Warm the hotplate or grill slightly, then turn the BBQ off and check it is cool enough to touch. Spray directly onto the surface. Leave for two to three minutes so the formula can break down the grease. Wipe clean with a damp cloth or a Selleys BBQ Tough Wipe, then wipe again with a clean cloth to remove any residue. For heavier build-up, spray on and scrub lightly before wiping off. Cleaning each time you barbecue helps stop stubborn grime from forming. Important notes Do not use on BBQ decals, prints, signs, dial marks or clear plastics. Wipe off brass and painted surfaces straight away. Spot test on an inconspicuous area if you are unsure about a surface. Keep out of reach of children. Specifications Brand Selleys Product BBQ Tough Grease & Grime Cleaner Size 500mL Format Trigger spray bottle, ready to use Base Water based, surfactant based Appearance Colourless liquid Caustic No (non-caustic) Action time 2 to 3 minutes Clean-up Damp cloth and water Suitable surfaces BBQ hotplates, grills and racks; outdoor furniture Not suitable for Decals, prints, signs, dial marks, clear plastics; avoid leaving on brass or painted surfaces Safety According to the manufacturer's Safety Data Sheet, this product is classified as hazardous under Safe Work Australia criteria, with the signal word Warning. It can cause skin irritation and serious eye irritation and is harmful to aquatic life. Wear protective gloves and eye protection, wash your hands thoroughly after use, and avoid releasing it to the environment. If it contacts skin, wash with plenty of soap and water. If it gets in eyes, rinse cautiously with water for several minutes, remove contact lenses if present and easy to do, and keep rinsing; get medical advice if irritation persists. Keep out of reach of children and read the label before use. The product is not classified as a Dangerous Good for transport by road, rail, sea or air. If poisoning occurs, contact a doctor or the Poisons Information Centre (Australia 13 11 26).
$9.13
Dunlop Grout Paint is the quick, budget-friendly way to make a tiled area look new again without raking out old or discoloured grout. The acrylic formula paints straight over existing grout lines with the built-in brush applicator, offering excellent opacity that covers even dark colours in a coat or two. Clean-up is easy, and a single 250ml bottle refreshes a surprisingly large area.Where to use itUse it over old or discoloured cement grout on indoor walls and floors and on outdoor walls. It is perfect for freshening bathrooms, kitchen splashbacks and laundry tiling, or for switching grout colour - brightening joints with Ultrawhite or going darker with Slate Grey or Jet Black for a modern contrast.How to useClean the grout thoroughly (Dunlop Tile & Grout Cleaner works well) and let it dry. Shake the bottle, then brush the paint along the grout line with the applicator, overlapping slightly onto the tile edge. Once touch dry - about 15-20 minutes at 23°C - wipe the overpainted edges off the tile faces with a damp cloth. Allow 2 hours' cure after cleaning, then polish the area with a soft cloth. The paint is fully set after 24 hours, after which showers can be exposed to water.Important notesNot suitable for swimming pools or external floors. Expect faster wear in areas with regular foot traffic or frequent exposure to water, soaps and chemicals such as shower floors. Coverage varies enormously with joint width and tile size - from about 1m² on small mosaic tiles with wide joints up to 200m² on large-format tiles with fine joints.Specifications Use on Old or discoloured grout joints Coverage guide Approx. 60m² per 250ml for 330 x 330mm tiles at 3mm joints Tile types Grout joints between most glazed ceramic and porcelain tiles Location Indoor walls and floors, outdoor walls SafetyAvoid contact with eyes and prolonged skin contact; wear gloves if desired and wash hands after use. Use with adequate ventilation, keep out of reach of children and refer to the Safety Data Sheet.
$18.71
Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.
$67.73
Dunlop Multipurpose Primer in the 4 litre pack is the job-sized version of Dunlop's water-based bonding primer, made for whole-room and whole-house preparation work. It improves the bond between the substrate and Dunlop floor levellers, renders, tile adhesives and waterproofing membranes, turning dusty, porous surfaces into a reliable base. It suits new and old concrete, particleboard and compressed fibre-cement sheets alike.Where to use itUse indoors or outdoors, on walls and floors. It is at home on fibre-cement sheeting, concrete slabs, masonry and lightweight concrete blocks, particleboard, renders and screeds, before levelling, rendering, tiling or waterproofing with Dunlop systems.How to usePrepare the surface so it is clean, dry and free of dust, grease and loose material. Pour out the primer and spread an even coat with a brush or roller, working it into the surface. Let it dry clear before applying the next product in your system. Wash tools in water immediately after use.Important notesOn very porous substrates a second coat is required to achieve a continuous primed film. The white-on, clear-dry formula shows exactly where you have coated. Actual coverage depends on substrate porosity and site conditions.Specifications Size 4 litres Coverage Approx. 6m² per litre (up to approx. 24m² per pack) Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyWear gloves and eye protection, keep the work area ventilated, and avoid prolonged skin contact. Keep away from children and refer to the Safety Data Sheet before starting.
$60.26
Dunlop Multipurpose Primer is a water-based primer engineered to strengthen the bond between a substrate and the Dunlop product applied over it. It is the go-to preparation step for flooring work, priming ahead of floor levellers, renders, tile adhesives and waterproofing membranes, and it performs equally well on new or old concrete, particleboard and compressed fibre-cement sheeting.Where to use itApproved for indoor and outdoor use on both walls and floors. Typical substrates include fibre-cement sheets, concrete, masonry and lightweight concrete blocks, particleboard, renders and screeds. Prime before levelling a slab, rendering a wall, waterproofing a bathroom or laying tiles.How to useSweep or vacuum the surface so it is clean, sound and free of dust, oil and curing compounds. Apply an even coat by brush or roller and allow it to dry clear before applying your leveller, render, adhesive or membrane. Because it is water-based, brushes and rollers wash out in water straight after use.Important notesVery porous substrates will drink in the first coat, so a second coat is required to build a proper film. The primer applies white and dries clear, making coverage easy to track. Coverage figures are a guide only and vary with surface condition.Specifications Size 1 litre Coverage Approx. 6m² per litre Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyKeep off skin and out of eyes, wear gloves, and ensure good ventilation while working. Store sealed and away from children. Consult the Safety Data Sheet for full handling guidance.
$34.59
Dunlop Primer & Additive is a ready-to-use liquid primer that boosts the grip between your substrate and the Dunlop products that go on top of it. Whether you are about to level a floor, lay tiles or roll out a waterproofing membrane, a quick coat of this milky-white liquid seals porous surfaces and gives adhesives, levellers and membranes a far stronger key to bond to. It doubles as a grout additive, improving flexibility, adhesion, colour depth and resistance to abrasion and staining.Where to use itSuitable for both indoor and outdoor projects, on walls and floors. Use it over concrete, cement sheet, fibre-cement, plasterboard, sheeting and timber before applying Dunlop tile adhesives, floor preparation products or waterproofing membranes.How to useMake sure the surface is clean, dry and free of dust or contaminants. Apply undiluted before waterproofing, tiling and timber floor preparation; dilute it for priming wall board. On large floor areas a household broom works well to spread the primer and push it into the surface. Allow it to dry clear before continuing with your adhesive, leveller or membrane. Tools rinse out in water while the product is still wet.Important notesCoverage varies with the porosity of the substrate. The primer goes on white and dries clear, so you can easily see where you have already coated. Highly porous surfaces may need extra material.Specifications Size 1 litre bottle Coverage Approx. 4m² per litre undiluted; approx. 8m² per litre diluted Substrates Concrete, cement sheet, fibre-cement, plasterboard, timber Colour Applies white, dries clear SafetyWork in a ventilated area, avoid contact with skin and eyes, and keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.50
Use before bonding polyolefins with a Loxeal super glue: Prime the surface, then bond with Istant 23, Istant 25, Istant 27 or Istant 43. Loxeal Primer 7 Polyolefin Primer 20ml Loxeal Primer 7 is a solvent-based surface primer that makes the “unglueable” plastics glueable. Applied before a cyanoacrylate super glue, it raises the surface energy of polyethylene (PE), polypropylene (PP), thermoplastic rubbers, EPDM, PTFE and silicones, transforming bond strength on these notoriously low-energy materials. It dries in seconds, is fluorescent under blue light so coverage can be checked, and is recommended for use with Loxeal Istant 34 and other ethyl cyanoacrylate adhesives. Supplied in a 20ml bottle. Why choose Loxeal Primer 7? Unlocks polyolefins – makes PP, PE, PTFE, EPDM and silicone bondable with standard super glues Fast and simple – brush on a thin coat, wait a few seconds, then glue as normal Verifiable coverage – fluoresces under a blue lamp for quality control Long working window – primed surfaces stay active for up to one hour Ultra-thin, fluid consistency – roughly 1.5 mPa·s for even wetting of the surface Typical applications Bonding polypropylene and polyethylene parts, containers and housings PTFE, silicone rubber and EPDM components that resist ordinary adhesives Thermoplastic rubber grips, seals and trims Production and repair work on low surface energy plastics How to use Ensure surfaces are clean and dry. Brush a thin coat of Primer 7 onto the surfaces to be bonded and let it dry for a few seconds. Apply your cyanoacrylate adhesive and press the parts together – handling strength develops within seconds. Bond within one hour of priming for best results; reapply primer if more than eight hours pass. Reseal the bottle immediately after use. Usage notes Primer 7 is intended only for difficult, low surface energy materials – do not use it on substrates that bond readily without priming. Best adhesion is achieved when parts are joined within an hour of application. Specifications Chemistry Aliphatic amine in organic solvent Appearance Colourless; fluorescent under blue light Viscosity (+25°C) 1.5 mPa·s Specific weight (+25°C) 0.7 g/ml On-part life Bond within 1 hour; reapply after 8 hours Shelf life 1 year in original unopened packaging at +25°C Pack size 20ml bottle Important notes Solvent based – use in a well-ventilated area away from ignition sources. Store in a cool, dry place below +20°C and do not refill containers with used product. Seal the bottle immediately after each use to preserve the contents. Safety Consult the Safety Data Sheet (SDS) before use and wear suitable protection when handling. This information is provided as a general guide only. Always test on your specific materials and refer to the manufacturer's technical documentation before use.
$24.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 100g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. This 100g workshop bottle is the economical choice for production lines, maintenance teams and busy workshops that go through super glue regularly. Why choose Loxeal Istant 23? Trade-size 100g bottle – keeps high-use workshops and production benches running Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Solvent-free, single part – clear cure with tensile strength of 12–25 N/mm² Typical applications Production assembly and repetitive bonding tasks O-rings, seals and neoprene/NBR rubber components Maintenance and repair across rubber, metal and plastic parts Workshops and trades that need a reliable everyday instant adhesive in volume How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 100g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$54.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 25 Super Glue Medium Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 25 is a medium-to-high viscosity super glue based on ethyl cyanoacrylate, designed for bonding plastic, rubber, metal and ceramic – including slightly irregular surfaces where a runny glue would simply drain away. At 350–450 mPa·s it stays where you put it, fills gaps up to 150 microns and fixtures in seconds, with a medium setting speed that gives you a moment to position parts. Supplied in a 20g bottle. Why choose Loxeal Istant 25? Medium viscosity – controllable application that stays put on the joint Handles imperfect surfaces – fills gaps of 10–150 microns Broad substrate range – plastic, rubber, metal and ceramic with one product Fast, strong fixture – tensile strength of 15–23 N/mm² when cured Solvent-free, single part – clean, clear bond line with no mixing Typical applications Repairs on ceramics, ornaments and household items Bonding rubber and plastic parts with less-than-perfect mating surfaces Metal-to-plastic and metal-to-rubber assemblies General workshop, trade and hobby bonding How to use Clean and degrease both surfaces and allow them to dry fully. Apply a modest bead or drops to one surface only. Assemble the parts promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; phenolic resin 5–20 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 350–450 mPa·s (medium) Gap fill 10–150 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 15–23 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$22.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 20g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. Supplied in a 20g bottle that suits both the workbench and the kitchen drawer. Why choose Loxeal Istant 23? Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Clear, strong bond line – colourless cure with tensile strength of 12–25 N/mm² Solvent-free, single part – no mixing, no clamping hardware, straight from the bottle Typical applications Everyday repairs across rubber, metal and plastic parts O-rings, seals and neoprene/NBR rubber components Small component assembly in production and maintenance work Household and hobby fixes where a fast, tidy bond is needed How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$17.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 27 Super Glue High Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 27 is a high viscosity, gap-filling super glue based on ethyl cyanoacrylate, made for irregular surfaces on plastic, rubber, metal and ceramic. Its thick 1,200–1,800 mPa·s consistency bridges gaps up to 200 microns without running, and its deliberately slower fixture time lets you adjust and align parts during assembly before the bond locks in. Supplied in a 20g bottle. Why choose Loxeal Istant 27? High viscosity, gap-filling formula – fills gaps of 10–200 microns on uneven surfaces Stays where applied – thick consistency will not run out of the joint or drip Repositioning window – slower fixture allows parts to be adjusted during assembly Strong final bond – tensile strength of 18–25 N/mm² when cured Solvent-free, single part – clear cure straight from the bottle Typical applications Bonding rough, porous or poorly matched surfaces Plastic and rubber parts with irregular mating faces Ceramic repairs where a runnier glue would soak away or drip Assemblies that need a few extra seconds of alignment time How to use Clean and degrease both surfaces and allow them to dry fully. Apply a bead of adhesive to one surface only. Assemble the parts, adjust alignment while the slower fixture time allows, then hold with light pressure. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; phenolic resin 10–40 seconds; aluminium 10–30 seconds; ABS 15–40 seconds; PVC 20–50 seconds; steel 20–50 seconds; zinc 40–100 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 1,200–1,800 mPa·s (high) Gap fill 10–200 microns Fixture time 5–100 seconds, substrate dependent Tensile strength 18–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$22.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 43 Speciale Super Glue Cyanoacrylate Adhesive 50g Loxeal Istant 43 Speciale (43S) is a surface-insensitive, general purpose super glue based on modified ethyl cyanoacrylate. Unfazed by acidic and porous surfaces, it excels at bonding leather, wood, fabric, ceramic and metals where ordinary super glues struggle. It offers proven heat resistance to +120°C (short peaks to +150°C) and is NSF registered for use in and around food processing areas, making it a favourite for demanding trade and industrial work. Supplied in a 50g bottle. Why choose Loxeal Istant 43 Speciale? Surface insensitive – cures reliably on acidic and porous substrates like leather, wood and paper Heat resistant – holds strength up to +120°C, with short-term peaks to +150°C NSF registered – acceptable for use as an instant adhesive in and around food processing areas Very fast on hard-to-glue materials – fabric in 2–20 seconds, leather in 5–15 seconds Strong all-rounder – medium viscosity with tensile strength of 15–25 N/mm² Typical applications Leather goods, footwear and upholstery repairs Woodworking, trim and joinery fixes across many timber species Equipment maintenance around commercial kitchens and food processing plants Fabric, ceramic, metal and rubber bonding in workshops and on site How to use Clean and degrease all surfaces and allow them to dry before applying the adhesive. For low-energy plastics such as PE, PP or PTFE, apply Loxeal Primer 7 first and let it dry. Apply the adhesive sparingly to one surface, then bring the parts together quickly and correctly aligned – the fast cure leaves little room for repositioning. Press firmly for a few seconds until fixed, and keep parts clamped until fully set. Wait 24–72 hours for full cure before applying any mechanical stress. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: paper 1–5 seconds; fabric 2–20 seconds; PVC, ABS and phenolic resin 2–10 seconds; aluminium 2–10 seconds; steel 5–20 seconds; leather 5–15 seconds; ceramic 5–30 seconds; softwoods 5–20 seconds; oak 90–180 seconds. Loxeal Activator 9 can be used to accelerate slow joints. Full cure in 24–72 hours. Specifications Chemistry Modified ethyl cyanoacrylate Colour Clear Viscosity (+25°C) 80–150 mPa·s (medium) Gap fill 10–150 microns Fixture time 1–180 seconds, substrate dependent Full cure 24–72 hours Tensile strength 15–25 N/mm² (ISO 6922) Service temperature -50°C to +120°C (peaks to +150°C) Approvals NSF registered for food processing areas Shelf life 12 months in original unopened packaging Pack size 50g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Not approved for use with pure or gaseous oxygen. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$29.95
Loxeal 30-22 UV-Curable High Viscosity Adhesive 50ml Loxeal 30-22 is a fast-curing, high-strength UV adhesive with a thicker, higher-viscosity consistency designed for glass-to-glass and glass-to-metal bonding. The heavier body gives better control on the joint and lets it bridge gaps up to 2 mm, while its crystal-clear, non-yellowing finish with over 98% light transmittance keeps even generous bond lines virtually invisible — ideal for precious crystal work. Why choose Loxeal 30-22? High viscosity (5,500–7,500 mPa·s) resists flowing off the joint before cure Fills bond lines from 0.03 mm up to 2 mm — more forgiving on uneven parts Cures in seconds under UV light (365 nm) Clear, colourless joints with excellent optical clarity Strong bonds on glass-to-glass and glass-to-metal assemblies Typical applications Glass-to-glass and glass-to-metal bonding in glass furniture, decorative items and crystal ware — especially assemblies with larger or less uniform bond gaps where a runnier adhesive would drain away. How to use Ensure both parts are clean and completely dry. Apply the adhesive to one surface and bring the parts together. At least one part must be UV-transparent — position the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Extend the exposure for wider gaps or substrates that filter UV. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Cure time varies with lamp intensity, distance from the light source, bond-line gap and the light transmittance of the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 5,500–7,500 mPa·s Specific gravity 1.10 g/ml Gap fill 0.03–2 mm Tensile strength (ASTM D-2095-69) 8–12 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering substrates — extend exposure accordingly. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$69.95
Loxeal 30-20 UV-Curable Adhesive 50ml Loxeal 30-20 is a fast-curing, high-strength UV adhesive purpose-made for glass and crystal bonding. Under a suitable UV lamp it sets in as little as 6–10 seconds, and its water-clear finish with over 98% light transmittance makes joints all but invisible — the go-to choice for decorative tableware, household and furnishing accessories, giftware and fine crystal work. Why choose Loxeal 30-20? Cures in seconds under UV light (365 nm) — parts are handled almost immediately Exceptional optical clarity: clear, colourless, non-yellowing joints High bond strength on glass-to-glass and glass-to-metal assemblies Bridges bond lines from 0.03 mm up to 1.5 mm Convenient one-part product — no mixing, cures only where the light reaches Typical applications Bonding glass and crystal in decorative tableware, homewares, furnishing accessories, bonbonnières and gift articles; ideal for precious crystal pieces where the joint must stay invisible. How to use Ensure both parts are clean and completely dry. Apply a small amount of adhesive to one surface and bring the parts together. At least one part must be UV-transparent — align the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Allow slightly longer exposure for larger gaps or tinted substrates. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Actual cure time depends on lamp intensity, distance from the light source, bond-line gap and how much UV passes through the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 2,200–2,900 mPa·s Specific gravity 1.1 g/ml Gap fill 0.03–1.5 mm Tensile strength (ASTM D-2095-69) 10–14 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Cured Loxeal 30-20 shows excellent long-term resistance to alcohol and refrigerant gases and good resistance to gasoline. Sustained exposure to high humidity (90% RH at +40°C) reduces bond performance, so it is best suited to dry indoor service. Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering glass — extend exposure accordingly. Not recommended for permanently damp or wet environments. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$69.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 85-86 Thread Sealant High Temperature Anaerobic Adhesive 50ml Loxeal 85-86 is a high strength anaerobic adhesive for locking and sealing threaded joints on all metals, in both free and forced matings. It maintains its sealing performance up to +200°C and offers high resistance to thermal shock, vibration, water, gas, oils, fuels, refrigerant fluids and many other chemicals – making it the choice for hot pipework, gas lines and demanding sealing jobs where standard sealants fall short. Why choose Loxeal 85-86? Seals and locks in one step with high mechanical strength Keeps sealing up to +200°C (service range -55°C to +200°C) Works on all metals, including free and press-fit assemblies Resists thermal shock, vibration, fuels, refrigerants and many chemicals Generous gap fill up to 0.30 mm on threads up to M56 / 2″ Green colour, fluorescent under blue light, for easy inspection Certified and approved Approved for gas-tight threaded joints to EN 751-1 (DIN-DVGW) WRAS approved for contact with wholesome (potable) water Compliant with the UBA (German Environment Agency) declaration for potable water use BAM certified as a sealant in the presence of gaseous oxygen up to 20 bar at +60°C Typical applications Sealing threaded joints on gas, steam, hot water and heating pipework Potable water fittings (observe the potable-water cure times below) Refrigeration, fuel and industrial fluid lines exposed to heat and vibration How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a continuous bead circumferentially, 1–2 threads back from the leading edge, using enough product to give a complete seal. Assemble and tighten the joint, then wipe off any uncured excess. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 (this may reduce final strength). Cure times at +25°C Handling strength: 10–40 minutes Functional strength: 6–12 hours Full cure: 24–36 hours Before contact with potable water: allow 24 hours at +20°C for brass, copper and cast iron; 7 days for stainless steel and aluminium Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 2,200–4,000 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 15–25 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 40–55 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Recommended for metal thread joints only – contact a technical service before use on other materials. Do not contaminate the adhesive with metal; cut the nozzle to the required bead size. The liquid product can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. High strength – for disassembly, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts, bolts and studs of all types that may need to be dismantled later with standard hand tools. It tolerates minor oil contamination on the parts, so it keeps performing where threads are not perfectly clean. Once cured it resists vibration, corrosion, water, gas, oils, hydrocarbons and many other chemicals, and it holds its sealing properties from -55°C to +200°C (up to +250°C for short periods), with proven unscrewing resistance at +200°C. Why choose Loxeal 55-03? Medium strength – assemblies can be dismantled with normal tools when servicing is needed Tolerates light oil contamination on threads Locks and seals fasteners in one step, stopping loosening caused by vibration Wide service temperature range of -55°C to +200°C Blue colour, fluorescent under blue light, for easy inspection on the production line Seals the thread against ingress, helping prevent rust and fretting corrosion Certified and approved Approved as a gas-tight sealant for threaded fittings to European norm EN 751-1 (DVGW and Gaz de France) WRAS approved – suitable for use in contact with potable water Compliant with the UBA (German Environment Agency) declaration for potable water applications NSF registered in category S4 as acceptable for use as an adhesive in and around food processing areas Typical applications Securing nuts, bolts, studs and screws on machinery, vehicles and equipment subject to vibration Sealing threaded fittings on gas, water and compressed air lines Automotive, plumbing and general maintenance work where later disassembly must remain possible How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before putting the joint into service. On passive surfaces (e.g. stainless steel, plated parts) or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure (this may slightly reduce final strength). Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Viscosity (+25°C) 1,700–9,000 mPa·s, thixotropic Specific gravity (+25°C) 1.07 Max thread size / gap fill M36 / 0.25 mm Shear strength (ISO 10123) 9–13 N/mm² Breakaway torque (ISO 10964) 18–23 N·m Prevailing torque (ISO 10964) 9–16 N·m Service temperature -55°C to +200°C (+250°C short term) Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel, with good resistance to petrol, brake fluid, 50% water/glycol and acetone after 1,000 hours of exposure. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. Not approved for use with pure oxygen or oxygen-rich systems, and not suitable for sealing chlorine or other strong oxidising agents. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$14.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-14 Thread Sealant Anaerobic Adhesive 50ml Loxeal 55-14 is a medium strength anaerobic thread sealant for hydraulic and pneumatic threaded connectors up to 1-1/2″. It replaces PTFE tape and hemp for sealing against gases, water, LPG, hydrocarbons, oils and many other chemicals. A medium thixotropic consistency stops the sealant migrating out of the thread before or during cure, and the cured joint is highly resistant to heat, corrosion, shocks and vibration across a service range of -55°C to +150°C. Why choose Loxeal 55-14? General purpose sealer for hydraulic and pneumatic fittings up to 1-1/2″ Replaces PTFE tape and hemp – no shredding, no re-taping, no clogged valves Medium strength – joints can still be dismantled with normal tools Thixotropic formula stays on the thread instead of dripping or migrating Seals against gases, water, LPG, oils, hydrocarbons and many chemicals Resists shock, vibration and corrosion from -55°C to +150°C Typical applications Sealing threaded connectors on hydraulic and pneumatic systems Pipework carrying water, compressed air, LPG, oils and industrial fluids General plumbing and maintenance sealing of metal pipe threads How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a bead of sealant around the male thread so the gap is completely filled. Assemble and tighten the connection. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 2,500–12,000 mPa·s, thixotropic Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 12–18 N·m Prevailing torque (ISO 10964) 20–30 N·m Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Formulated for metal threads only – contact a technical service before use on other materials. The liquid sealant can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$34.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
You have seen 96 out of 214 products
Bottled adhesives with precision tips for controlled dots and lines on crafts, woodworking and assembly. Match open time and clamp needs to your project; store upright to avoid leaks. Use filters to refine by chemistry, cure speed and temperature rating. Always review the product page and TDS/SDS.
