A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$48.79
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0fda3f36-74b9-4f76-87c5-eecf1c56afcc.jpg?v=1754715680&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_3922d4f4-2f1d-4263-a2de-14b767df10ba.jpg?v=1754715681&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e4f50d8f-e0a6-4255-a242-9c3e7590f0f3.jpg?v=1754715675&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e401b93c-d8cb-46ff-be50-3f30c2495024.jpg?v=1754715675&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_84aa9bc6-f55e-40c0-afbe-820db6fddb04.jpg?v=1754715673&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0c7f6c0e-695e-4545-a57c-1e5bf7ca1f0c.jpg?v=1754715673&width=645)
$9.49
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$16.78
Cut through stubborn limescale, soap scum, and rust stains with Glitz Calcium Scale and Rust Remover. This powerful bathroom cleaner is formulated to lift mineral build up fast so sinks, taps, tiles, glass, and shower screens look clean and fresh again. The generous 2L size is ideal for whole home maintenance or trade use. Why you will love it Targets tough mineral deposits like calcium, lime, and rust Breaks down soap scum for a brighter, streak free finish Works on ceramic, porcelain, glass, chrome, stainless steel, and most bathroom surfaces Fast acting formula helps reduce scrubbing time 2L value size for households, cleaners, and facilities teams Best for Shower screens and doors Wall tiles and grout surrounds Basins, baths, and toilets on the exterior porcelain Taps, shower heads, and chrome fittings Not recommended for Avoid natural stone like marble, limestone, travertine, or terrazzo. Avoid enamel cookware, unsealed or damaged surfaces, and any surface that states not to use acidic cleaners. If unsure, test on a small hidden area first. How to use Preparation Remove loose debris and pre rinse the surface with warm water. Light scale and soap scum Dilute 1 part product to 4 parts water. Apply with a sponge or spray bottle. Heavy scale and rust stains Use undiluted. Apply directly to the stain and let it sit for 2 to 5 minutes. Do not allow to dry on the surface. Agitate Wipe or scrub with a non scratch pad or soft brush. Rinse well Flush thoroughly with clean water until the surface is neutral and residue free. Repeat if needed For very stubborn deposits, repeat the process in short contact times. Pro tips For shower heads with internal scale, remove the head and soak in a diluted solution. Rinse well before refitting. Squeegee shower glass after each use to slow future build up. Always spot test first. Some finishes are more delicate than others. Safety and handling Wear gloves and eye protection during use Use in a well ventilated area and avoid inhaling mist Do not mix with bleach or ammonia Keep out of reach of children and pets Store upright in a cool, dry place with cap closed After care Once deposits are removed, maintain surfaces with a neutral pH daily cleaner. Regular rinsing and drying will help prevent new mineral build up. Product details Brand Glitz Product Calcium Scale and Rust Remover Bathroom Deep Clean Size 2L Form Liquid Suitable surfaces Ceramic, porcelain, glass, chrome, stainless steel, most glazed tiles Do not use on Natural stone, terrazzo, unsealed or damaged surfaces, acid sensitive finishes Cleanup Rinse with plenty of clean water What is in the box 1 x Glitz Calcium Scale and Rust Remover 2L Good to know Contact time should be short. Rinse thoroughly to protect finishes. For vertical surfaces, apply with a sponge to reduce run off. For regular maintenance, switch to a gentle daily cleaner between deep cleans.
$23.66 $20.12
Glitz Spray On Wipe Off is your quick daily cleaner for busy kitchens, bathrooms, and high touch areas. Just spray, wipe, and you are done. It cuts through everyday grease, food splatter, soap scum, and dust to leave surfaces fresh and streak free. Why you will love it Fast spray and wipe action for daily clean ups Lifts light grease, grime, and sticky residues Streak free finish on most hard household surfaces Fresh clean scent that does not linger Ready to use 750ml trigger bottle for easy coverage Ideal for Benchtops and splashbacks Stainless steel appliances and rangehood exteriors Cooktops when cool, microwaves, fridges, and pantry shelves Bathroom vanities, taps, tiles, and shower glass Tables, desks, cabinet doors, light switches, and door handles Not recommended for Unsealed or waxed surfaces Natural stone such as marble, limestone, or travertine Untreated wood, leather, or fabrics Plasma or non glass coated display screens How to use Turn nozzle to the ON position. Spray directly onto the surface from about 20 cm away. Wipe with a clean damp cloth or paper towel. For stuck on grime, leave for 30 to 60 seconds before wiping. Buff with a dry cloth for a clear finish. Return nozzle to OFF after use. Pro tips Always test on an inconspicuous spot first. For food preparation areas, wipe with a clean damp cloth after cleaning. Use a microfiber cloth for best streak control on glass and stainless steel. Product details Brand Glitz Product type Everyday spray cleaner Format Ready to use Fragrance Fresh clean Bottle size 750 ml Surface compatibility Most sealed hard surfaces including laminate, ceramic, porcelain, stainless steel, glass, and finished wood What is in the box 1 x Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml with trigger Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other chemicals. FAQs Can I use it on stone benchtopsUse only on sealed engineered stone. For natural stone like marble or limestone, use a stone specific cleaner. Does it leave residueIt is designed to wipe clean. For food areas, finish with a damp cloth to remove any remaining cleaner. Is it suitable for glassYes for quick touch ups. For crystal clear windows, follow with a dry microfiber buff. Good to know Great for daily resets after cooking and bath time Trigger head lets you choose between stream and spray patterns Pairs well with microfiber cloths and paper towels
$6.71 $5.27
Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml Glitz Spray On Wipe Off is your quick daily cleaner for busy kitchens, bathrooms, and high touch areas. Just spray, wipe, and you are done. It cuts through everyday grease, food splatter, soap scum, and dust to leave surfaces fresh and streak free. Why you will love it Fast spray and wipe action for daily clean ups Lifts light grease, grime, and sticky residues Streak free finish on most hard household surfaces Fresh clean scent that does not linger Ready to use 750ml trigger bottle for easy coverage Ideal for Benchtops and splashbacks Stainless steel appliances and rangehood exteriors Cooktops when cool, microwaves, fridges, and pantry shelves Bathroom vanities, taps, tiles, and shower glass Tables, desks, cabinet doors, light switches, and door handles Not recommended for Unsealed or waxed surfaces Natural stone such as marble, limestone, or travertine Untreated wood, leather, or fabrics Plasma or non glass coated display screens How to use Turn nozzle to the ON position. Spray directly onto the surface from about 20 cm away. Wipe with a clean damp cloth or paper towel. For stuck on grime, leave for 30 to 60 seconds before wiping. Buff with a dry cloth for a clear finish. Return nozzle to OFF after use. Pro tips Always test on an inconspicuous spot first. For food preparation areas, wipe with a clean damp cloth after cleaning. Use a microfiber cloth for best streak control on glass and stainless steel. Product details Brand Glitz Product type Everyday spray cleaner Format Ready to use Fragrance Fresh clean Bottle size 750 ml Surface compatibility Most sealed hard surfaces including laminate, ceramic, porcelain, stainless steel, glass, and finished wood What is in the box 1 x Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml with trigger Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other chemicals. FAQs Can I use it on stone benchtops Use only on sealed engineered stone. For natural stone like marble or limestone, use a stone specific cleaner. Does it leave residue It is designed to wipe clean. For food areas, finish with a damp cloth to remove any remaining cleaner. Is it suitable for glass Yes for quick touch ups. For crystal clear windows, follow with a dry microfiber buff. Good to know Great for daily resets after cooking and bath time Trigger head lets you choose between stream and spray patterns Pairs well with microfiber cloths and paper towels
$33.11 $26.17
Glitz Sugar Soap for Floors Heavy Duty Cleaner Power through ground-in dirt, grease, and everyday grime with Glitz Sugar Soap for Floors. This heavy duty formula lifts stubborn residues and leaves floors fresh, streak free, and ready for living. Ideal for high traffic areas in homes, workshops, and commercial spaces. Why you will love it Heavy duty clean that cuts through grease, scuff marks, and sticky spills Low foam for a streak free finish on most sealed floors Fast acting formula reduces scrubbing time Residue free so finishes and sealers look their best Fresh, low odour for comfortable indoor use Best for these surfaces Use on most sealed and washable floors, including: Ceramic and porcelain tiles Vinyl and hybrid floors Laminate and sealed timber Sealed concrete and epoxy coated floors Do not use on unsealed timber, unsealed cork, natural stone that is unsealed, or waxed finishes. Always test in a small inconspicuous area first. How to use Sweep or vacuum to remove dust and grit. Dilute in warm water: General cleaning: 1 capful per 5 L bucket Heavy duty cleaning: 2 to 3 capfuls per 5 L bucket Apply with a mop or sponge. Work in sections. For stubborn spots, apply a little solution directly, wait 2 to 3 minutes, then gently agitate. Rinse mop frequently in clean water. Allow floor to dry before walking. Pro tips Change the bucket water when it turns cloudy to avoid streaks. Use heavy duty dilution before repainting or resealing floors to remove grease and prep the surface. For gloss finishes, wring the mop well to prevent pooling. Product details Brand Glitz Product type Sugar soap floor cleaner Format Liquid concentrate Appearance Clear to light solution, low foam Suitable surfaces Most sealed hard floors Clean up Rinse tools and mops in clean water Storage Keep tightly closed in a cool, dry place Safety Wear gloves if you have sensitive skin. Avoid contact with eyes. If splashed, rinse with water. Keep out of reach of children and pets. FAQs Do I need to rinse after cleaning Rinsing is generally not required on sealed floors when diluted as directed. If using heavy duty strength, a light rinse with clean water can help achieve a streak free finish. Can I use it in a spray mop Yes. Pre dilute following the general cleaning ratio and avoid over wetting the floor. Good to know Compatible with most microfiber and cotton mops Great prep step before resealing or repainting floors Helps remove oily residues that make floors feel slippery
$5.27 $4.94
Glitz Daily Shower Cleaner Prevents Soap Scum Build Up 750ml Keep your shower looking fresh with this easy daily spray. Glitz Daily Shower Cleaner helps prevent soap scum and mineral build up so glass, tiles, and fittings stay clearer for longer. No heavy scrubbing required. Just spray and go as part of your routine. Key benefits Helps stop soap scum forming between deep cleans Cuts through light residue from body wash and shampoo Streak free finish on shower screens when used as directed Fast application for busy bathrooms Fresh clean scent that leaves the space smelling pleasant Where to use Shower glass and screens Ceramic tiles and grout surrounds Fibreglass and acrylic bases Chrome and stainless steel fittings Sealed stone and laminate surfaces in wet areas Always test first on an inconspicuous spot. Avoid unsealed stone, marble that is not sealed, brass, copper, and any surface that is not water safe. How to use After showering, quickly rinse surfaces with warm water. Set nozzle to spray. Mist evenly over glass, tiles, and fittings. Leave to work. No rinse required on light residue. For heavier build up, wipe with a soft cloth or squeegee. Use daily to help prevent soap scum returning. Pro tips Keep a squeegee in the shower and pull down glass before spraying for the best clarity. Ventilate the bathroom to reduce fogging and moisture marks. Pair with a weekly deep clean for grout lines and corners. Good to know Non abrasive formula suitable for regular use Safe for most sealed surfaces when used as directed Family friendly routine cleaner for shared bathrooms Specifications Product Daily shower maintenance spray Size 750 ml trigger bottle Suitable surfaces Glass, ceramic tile, acrylic, fibreglass, chrome, stainless steel, sealed stone Finish Clear streak free when wiped or squeegeed Use frequency Daily after showering Safety Read label before use. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other cleaners. Store upright in a cool dry place. Frequently asked questions Do I need to rinse after spraying For light daily residue, no rinse is needed. For visible build up, wipe or squeegee for a clear finish. Will it remove heavy limescale It is designed to prevent and control light residue. For stubborn limescale, use a suitable descaler first then maintain with daily use. Is it safe on natural stone Use only on sealed stone. Test first and avoid unsealed or delicate stone surfaces. What is in the box 1 x 750 ml Glitz Daily Shower Cleaner with adjustable trigger
$11.61 $10.44
Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25L is your everyday helper for a fast, streak free clean. Spray, wipe, and enjoy a bright finish on benches, tables, appliances, and other sealed surfaces around the home. Why you will love it Cuts through daily grime and light grease with ease Leaves a streak free shine on most sealed surfaces Fresh, clean household scent that does not linger No rinsing required on lightly soiled areas Ready to use for quick jobs or dilute for larger areas to save cost Best for Kitchen benches, tables, cupboards, splashbacks Bathroom vanities, tiles, taps, glass shower screens outside surface only Door handles, light switches, appliances exterior, bins Floors when diluted in a bucket for general freshen ups Do not use on Unsealed or waxed timber Natural stone that is unsealed or acid sensitive such as marble and limestone Screen displays or electronics Delicate finishes. Always spot test in a hidden area first How to use Light cleaning. Spray directly onto the surface and wipe with a clean cloth Heavier soil. Let sit for 30 to 60 seconds then wipe. Repeat if required Floors. Add 60 to 100 ml per 5 L of warm water, mop, then allow to dry Glass and glossy areas. Use a lint free cloth and buff dry for best results Quick tips Use separate cloths for kitchen and bathroom to avoid cross contamination For stainless steel, always wipe with the grain and finish with a dry cloth On painted surfaces, apply to cloth first, not directly to the wall Specifications Brand Glitz Product Domestic Cleaner Multi Purpose Surface Shine Format Ready to use liquid. Dilutable for floors Pack size 1.25 L bottle Fragrance Fresh household scent Surface compatibility Most sealed hard surfaces including laminates, sealed stone, ceramic tile, porcelain, stainless steel, enamel, and sealed timber Country of use Suitable for Australian homes and water conditions What is in the box 1 x Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25 L Storage and safety Store upright in a cool, dry place away from direct sunlight Keep out of reach of children and pets Avoid contact with eyes. If in eyes rinse with water Do not ingest. If swallowed seek medical advice Frequently asked questions Can I use it on food contact areas Yes. Clean the surface, then wipe with a damp cloth and allow to dry before food preparation Will it leave residue No when used as directed. Buff with a dry cloth on glass or glossy areas for a crystal finish Is rinsing required Not for light soil. For heavy soil or floors, rinse the mop head regularly for best results Good to know Ideal for quick daily resets in kitchens and bathrooms Economical size that suits family households and shared spaces
$6.51 $6.04
Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 2L, Make light work of dishes with a refreshing lemon clean. Glitz Citrus Dishwashing Liquid delivers rich suds that lift grease and food residues fast, leaving plates, glasses, and cookware spotless with a fresh citrus finish. The generous 2L, bulk pack is ideal for busy family homes, offices, cafes, and community kitchens that want reliable performance and great value. Why you will love it Powerful everyday clean that breaks down oils and baked on residues Fresh lemon fragrance for a just cleaned scent Stable foam for longer sink time and fewer top ups Rinses easily to help reduce spotting and streaks Cost effective 2L, format for regular high volume washing Versatile for hand washing dishes, cutlery, glassware, and cookware Best for Daily sink loads at home or in shared kitchens Cafes, lunchrooms, clubs, and community events Rental properties and short stay turnovers How to use Fill sink with warm water. Add dishwashing liquid. Start with 1 to 2 teaspoons per 2L, of water for light to normal soils. Increase for heavy grease. Wash using a sponge or brush. Soak stubborn items for a few minutes. Rinse thoroughly with clean water and allow to air dry or towel dry. Tips For glassware, use hot water and a soft sponge to help prevent water spots. Change solution when suds begin to collapse or water appears cloudy. Do not use in automatic dishwashers. This formula is for manual washing. Product details Brand Glitz Product Citrus Dishwashing Liquid Fragrance Fresh Lemon Format Liquid Size 2L, Use Manual dishwashing and general sink cleaning Suitable surfaces Dishes, cutlery, glassware, ceramics, stainless steel cookware Country of use Australia What is in the box 1 x Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 2L, Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If product gets in eyes rinse with water. If irritation occurs discontinue use. Sustainability note Use the recommended dose to minimise waste and water use. Recycle the container where local facilities allow. Frequently asked Can I use it on non stick cookware Yes, use a soft sponge and follow the cookware care instructions. Is it safe for septic systems This hand dishwashing liquid is designed for general household use. As with any cleaner, use as directed and follow local guidance for septic systems.
$13.69 $10.99
Glitz Eucalyptus Oil Natural Antibacterial Cleaner 250ml Bring a fresh, clean finish to kitchens, bathrooms, floors and everyday surfaces. This eucalyptus oil based cleaner cuts through grease and grime while leaving a naturally crisp fragrance. Ideal for quick wipe downs or deeper cleans where you want plant based antibacterial action without harsh bleaching agents. Why you will love it Natural antibacterial action from eucalyptus oil for hygienic everyday cleaning Multi surface formula suitable for benches, tiles, stainless steel, sealed stone and more Residue free finish that dries fast and leaves a fresh eucalyptus scent Versatile use for spot cleaning sticky residues, deodorising bins and refreshing soft surfaces Compact 250ml size that is easy to store at home, in the office or on the go Best for Kitchen benches, splashbacks and sinks Bathroom fixtures, tiles and grout surrounds Stainless steel appliances and rangehoods Doorknobs, light switches and high touch areas Removing sticky label residue from glass and metal How to use General surface clean: Add 1 to 2 capfuls to 1 litre of warm water. Dampen a cloth or mop, wring out well and wipe the surface. Allow to air dry. Spot clean and adhesive removal: Apply a small amount to a soft cloth, gently rub the area, then wipe with a damp cloth. Deodorise: Add a few drops to a cloth and wipe bins or pet areas, then rinse surfaces that contact food. Always test on a hidden spot first. Rinse food contact surfaces with potable water after use. What is inside Eucalyptus oil based cleaner with fresh fragrance No chlorine bleach No added dyes Good to know Fast drying formula helps reduce streaks on glossy finishes Plant derived solvent helps cut through greasy marks A little goes a long way thanks to a concentrated base Safety and storage Keep out of reach of children and pets Use in a well ventilated area Flammable liquid and vapour. Keep away from heat, sparks and open flames Avoid contact with eyes and prolonged skin contact Do not use on unsealed wood, raw stone or painted surfaces that are not colourfast Store upright in a cool, dry place with the cap tightly closed Specifications Brand Glitz Product Eucalyptus Oil Natural Antibacterial Cleaner Size 250 ml Fragrance Fresh eucalyptus Suitable surfaces Benchtops, tiles, laminate, sealed stone, stainless steel, glass Not recommended for Unsealed wood, raw stone, leather, silk, unfinished surfaces Country of use Australia Tips for great results For shiny surfaces, buff dry with a clean microfiber cloth after wiping On stubborn residue, allow the product to sit for 30 seconds before wiping Use separate cloths for kitchen and bathroom zones to avoid cross contamination Frequently asked questions Can I use it on stone benches Yes, on sealed stone. Always test first and avoid soaking grout lines. Is it safe around food prep areas Yes, when used as directed. Rinse food contact surfaces with clean water after cleaning. Will it remove sticker residue Yes. Apply a small amount to a cloth, rub gently, then wipe clean with a damp cloth. What you get 1 x Glitz Eucalyptus Oil Natural Antibacterial Cleaner 250ml Shipping and returns Fast dispatch Australia wide from our Melbourne warehouse Tracked delivery with email updates Hassle free returns according to Glues Australia policy Glues Australia keeps Australia clean and together with trusted brands, practical advice and fast shipping.
$22.59 $17.15
Glitz Pine Disinfectant Commercial Grade Sanitiser 5L Refresh and sanitise high traffic areas with the classic clean of pine. Glitz Pine Disinfectant is a commercial grade cleaner that cuts through everyday grime, removes unpleasant odours, and leaves a crisp pine aroma. Ideal for homes, workplaces, schools, gyms, and hospitality areas where a fast, reliable clean is needed. Why you will love it Commercial grade performance for large and small areas Deodorises while it cleans with a fresh pine scent Versatile on sealed floors, benches, walls, bathrooms, and bins Low effort mop and wipe application Economical 5L size suited to frequent use and refill stations Where it works Sealed hard floors including tiles, vinyl, sealed concrete, and sealed timber Bathrooms, toilets, showers, and change rooms Kitchen and lunchroom benches, splashbacks, and cupboards Door handles, railings, desks, and other high touch points Bins and pet areas surfaces only, avoid direct contact with food How to use Always test on a small inconspicuous area first. Do not use on unsealed or porous stone. Avoid prolonged contact with natural marble and other acid sensitive surfaces. Application Dilution guide Directions General mopping and daily clean 1:80 to 1:100 (50 to 100 mL per 8 L bucket) Add to warm water, mop the surface, then allow to air dry. No rinse required on lightly soiled, non food contact areas. Bathrooms and heavy soil 1:10 to 1:20 Apply with sponge or cloth, scrub if needed, allow contact for 5 minutes, then rinse with clean water. Spray and wipe 1:20 in a trigger bottle Spray onto surface, wipe with a clean microfibre cloth, and let dry. Rinse food contact surfaces with potable water. Deodorising bins and drains Neat or 1:5 Rinse the area first, apply, allow contact time, then rinse away. Pro tips Use separate colour coded cloths and mops for bathrooms and kitchens to reduce cross contamination. For streak free floors, wring the mop well and change the solution when it becomes visibly dirty. Store the concentrate upright with the cap sealed to preserve freshness. Product details Brand Glitz Product type Pine disinfectant and sanitising cleaner Fragrance Pine Form Liquid concentrate Container size 5 litres Suitable surfaces Sealed hard floors, tiles, vinyl, sealed concrete, bathrooms, benches, walls Do not use on Unsealed stone, natural marble, unfinished timber, fabrics, or screens Safety and handling Read label before use. Keep out of reach of children. Use in well ventilated areas. Avoid breathing spray. Wear gloves if you have sensitive skin or prolonged contact is expected. Avoid contact with eyes. If in eyes, rinse with water for several minutes. Do not ingest. If swallowed, seek medical advice. Store in a cool, dry place away from direct sunlight. Frequently asked questions Can I use this on food contact surfaces Yes, but after cleaning you must rinse those surfaces with potable water. Will it leave a sticky residue When used at the recommended dilutions and allowed to dry, it leaves a fresh, clean finish without tackiness. Is it pet friendly Allow surfaces to dry completely before pets return. Do not allow pets to ingest the solution. Good to pair with Microfibre cloths for streak free wipe downs Colour coded mop heads and buckets for hygiene zones Trigger spray bottles for quick touch up cleans
$27.62 $20.89
Glitz Pine Disinfectant Household Germ Killer 750ml Bring a fresh pine clean to kitchens, bathrooms, floors, and bins with Glitz Pine Disinfectant. This ready to use household disinfectant helps kill household germs, deodorises problem areas, and leaves a classic pine scent that says clean. Ideal for everyday wipe downs or quick sanitising between deeper cleans. Why you will love it Household germ killer for hard, non porous surfaces Fresh pine fragrance that neutralises odours Versatile cleaner for kitchens, bathrooms, floors, and bins Streak free finish on tiles, vinyl, sealed stone, and laminate Convenient 750ml size for grab and go cleaning Best for Benchtops, splashbacks, sinks, and taps Toilets, showers, baths, and tiles Floors, entryways, and high touch areas Bins, pet zones, and outdoor furniture made from hard, washable materials How to use Remove loose dirt and debris first. Apply directly to the surface or onto a clean cloth or mop. Spread to cover the area evenly and allow a short contact time. Wipe clean. For food contact areas, rinse with potable water after disinfecting. Tips For heavy soil, pre clean, then reapply and allow extra contact time. Test on an inconspicuous area of delicate finishes before full use. Use a fresh cloth or mop head for hygienic results. What not to do Do not use on unsealed wood, fabric, or porous stone. Do not mix with other chemicals, especially ammonia or bleach products. Frequently asked questions Can I use it on stone benchtopsYes, on sealed stone only. Rinse food prep areas with potable water after disinfecting. Is it suitable for floorsYes. Apply lightly to tiles, vinyl, or sealed laminate and mop evenly. Does it remove odoursYes. The pine fragrance helps neutralise household odours as it cleans. Safety Keep out of reach of children. Avoid contact with eyes and prolonged skin contact. Wash hands after use. If product enters eyes, rinse with water. Store upright in a cool, dry place away from direct sunlight. Product details Brand Glitz Product Pine Disinfectant Household Germ Killer Format Ready to use liquid Fragrance Pine Size 750ml Surfaces Hard, non porous washable surfaces Country Australia Disposal Dispose of contents in accordance with local regulations. Rinse and recycle the empty bottle where facilities exist. Good to know Everyday strength suitable for regular home use Leaves rooms smelling clean and refreshed
$6.07 $5.23
Glitz Glass Cleaner for Crystal Clear Surfaces Give windows, mirrors, and glass splashbacks a streak free shine with Glitz Glass Cleaner. This fast drying spray cuts through fingerprints, water spots, and everyday grime so you can enjoy a spotless, crystal clear finish in seconds. Why you will love it Streak free clarity for windows, mirrors, and glass doors Fast acting formula lifts fingerprints and smudges Quick drying finish helps resist new marks Ideal for stainless trims, ceramic cooktops, and glossy tiles test first Fresh, clean scent that leaves surfaces looking like new Where to use Windows, mirrors, shower screens, glass tables Car and caravan interior glass use sparingly on tinted film and test in a small area first Kitchen splashbacks and glossy surfaces not suitable for unfinished stone or porous surfaces How to use Spray a light, even mist onto the surface. Wipe immediately with a clean, lint free cloth or paper towel. For best results, finish with a dry microfiber cloth using circular motions. For heavy build up, repeat the application as needed. Pro tips Work out of direct sunlight to reduce rapid evaporation. Use one cloth to clean and a second dry cloth to buff for a showroom shine. Replace cloths when damp to avoid streaks. Key details Surface type Glass, mirror, glazed ceramic, glossy tiles Finish Clear, streak free Use Household, office, automotive interior glass Fragrance Fresh clean scent Application Spray and wipe Good to know Always test on an inconspicuous area before full use. Do not use on unsealed stone or porous surfaces. Keep out of reach of children. Avoid contact with eyes. Store upright in a cool, dry place with the cap closed. What is in the box 1 x Glitz Glass Cleaner FAQs Will it leave streaksUsed with a clean, dry microfiber cloth, the finish is clear and streak free. Can I use it on tinted windowsTest first on a small area of the film. Apply to the cloth, not directly to the film, and wipe gently.
$15.07 $11.65
Glitz Hand Wash Gentle Moisturising Formula 5L Keep hands fresh and cared for with Glitz Hand Wash Gentle Moisturising Formula. This generous 5 litre refill is perfect for homes, offices, gyms, schools, hospitality venues, and anywhere high hand hygiene is essential. The balanced formula cleans effectively while helping to maintain the skin’s natural moisture. Why you will love it Gentle everyday clean that is kind to skin Moisturising formula that helps prevent dryness with frequent washing Rich lather that rinses quickly to leave hands feeling soft Light, pleasant fragrance suitable for shared spaces Economical 5L size for easy refills and reduced plastic waste Ideal for liquid soap dispensers and pump bottles Best for High traffic bathrooms and kitchens Reception areas, classrooms, healthcare waiting rooms, warehouses, and workshops Refilling counter top and wall mounted dispensers How to use Decant into a clean, dry dispenser or pump bottle. Wet hands with clean water and apply one pump of hand wash. Rub palms, backs of hands, between fingers, and around thumbs for at least 20 seconds. Rinse thoroughly and dry with a clean towel or paper towel. Good to know Suitable for frequent use on most skin types Clear liquid designed to minimise dispenser staining Bulk size helps lower cost per refill Product details Brand Glitz Product Hand Wash Gentle Moisturising Formula Format Liquid hand wash Size 5 litres Use Everyday hand washing and dispenser refills Fragrance Light, fresh Colour Clear or lightly tinted Storage and shelf life Store upright in a cool, dry place away from direct sunlight Keep tightly closed between refills Safety For external use only Avoid contact with eyes. If contact occurs, rinse with water Keep out of reach of children Sustainability tips Refill existing pumps and dispensers to reduce plastic waste Rinse and recycle the bottle where local facilities allow
$36.87 $32.99
Glitz Degreaser Heavy Duty Kitchen Cleaner 500ml Cut through baked-on grease and everyday kitchen grime fast. Glitz Degreaser Heavy Duty Kitchen Cleaner is a ready to use spray designed for cooktops, rangehoods, splashbacks, benches, and more. It lifts fats, oils, and food residue so you get a clean, streak free finish with less scrubbing. Why you will love it Heavy duty action - breaks down stubborn grease, oils, and burnt on residue Ready to use - no mixing required, just spray, wait, and wipe Streak free finish - leaves hard kitchen surfaces looking fresh Versatile - ideal for stainless steel rangehood exteriors, ceramic and glass cooktops, tiled splashbacks, benches, cupboard doors, and BBQ exteriors Fast results - reduces scrubbing time on tough build up Best for these jobs Cutting grease on cooktops and around burners De gunking rangehood filters and exteriors Cleaning oven doors and surrounding panels Removing oily fingerprints on cupboard doors and fridges Wiping down tiled splashbacks and benchtops Directions Switch off appliances and allow surfaces to cool. Shake bottle gently. Turn nozzle to spray. Spray directly onto the soiled area from 15 to 20 cm. Allow 2 to 3 minutes contact time on heavy build up. Do not let dry on the surface. Wipe with a damp cloth or non scratch sponge. Rinse food contact surfaces with clean water and dry with a lint free cloth. Good to know Always test on an inconspicuous area first. Not recommended for unsealed or porous stone such as marble and limestone, unsealed timber, raw aluminium, brass, copper, or varnished surfaces. For painted surfaces, dilute on a cloth first and test. Do not use on hot surfaces. Avoid prolonged contact with stainless steel. Rinse and dry after cleaning. Do not mix with other cleaners or chemicals. Specifications Brand Glitz Product type Heavy duty kitchen degreaser Format Ready to use spray Size 500 ml Suitable surfaces Stainless steel exteriors, ceramic and glass cooktops, tiles, laminates, enamel, sealed stone, and most non porous hard surfaces Safety Wear gloves if you have sensitive skin. Use in a well ventilated area. Avoid breathing spray. Keep out of reach of children and pets. If product gets in eyes rinse with water for several minutes. If irritation persists seek medical advice. Frequently asked questions Can I use this on a hot plate or warm oven No. Always allow surfaces to cool before cleaning. Is it safe on food contact areas Yes, but after cleaning you must rinse the surface with clean water and dry. Will it remove baked on carbon inside an oven It helps on light to moderate build up. For heavy carbon you may need a dedicated oven cleaner. What is in the box 1 x Glitz Degreaser Heavy Duty Kitchen Cleaner 500ml spray bottle Glues Australia ships fast Australia wide. Questions about surface compatibility or bulk orders Contact our team and we will help you choose the right cleaner for the job.
$7.93 $6.33
Glitz Outdoor Cleaner Concentrate Patio and Wall Wash 2L Bring paths, pavers, walls, decks and outdoor furniture back to life with this powerful yet easy to use outdoor cleaner. The concentrated formula lifts dirt, grime and green growth stains so surfaces look fresh and ready for entertaining. Why you will love it Concentrated performance for great value per clean Cuts through built up outdoor grime and weather stains Works on concrete, brick, pavers, render, tiles, Colorbond, vinyl cladding and painted exterior walls Ideal for patios, driveways, paths, fences, outdoor furniture and pergolas Foam or bucket application. Hose or pressure rinse Fresh outdoor scent that leaves areas looking and smelling clean Where to use Patios and courtyards Driveways and footpaths Exterior walls and fences Outdoor tables, benches and seating Garage floors and sheds Dilution guide Mix with clean water. Always test on a small hidden area first. Job Ratio How to apply General outdoor cleaning 1 part cleaner to 20 parts water Apply, scrub lightly, leave 3 to 5 minutes, rinse well Heavy soil and traffic marks 1 part cleaner to 10 parts water Apply, agitate with stiff broom, leave up to 10 minutes, rinse well Stubborn green growth staining 1 part cleaner to 4 parts water Apply to dry surface, scrub, leave up to 10 minutes, rinse thoroughly Directions Sweep or hose loose debris from the surface. Dilute according to the guide. Wear gloves and eye protection. Apply by watering can, pump sprayer or foam gun. Work in small sections. Agitate with a deck brush or stiff broom. Do not allow to dry on the surface. Wait the suggested dwell time, then rinse thoroughly with a garden hose or pressure washer on a low fan setting. For very stubborn areas, repeat the process or increase dwell time within the recommended limits. Coverage Up to 120 square metres per bottle when used at the general cleaning dilution. Actual coverage varies with surface porosity and soil load. Surface compatibility Suitable: concrete, pavers, brick, stone, render, tiles, grout, Colorbond, vinyl cladding, painted exterior walls, outdoor plastics and resin furniture Use caution: bare aluminium, raw timber and natural stone like marble or limestone. Always spot test first Good to know Do not mix with other chemicals or acids Keep pets and children away from the area until fully rinsed and dry Avoid runoff into garden beds and waterways. Rinse lawns and plants with fresh water if exposed Specifications Brand Glitz Product Outdoor Cleaner Concentrate Patio and Wall Wash Size 2L Format Concentrate Fragrance Fresh outdoor scent Country of use Suitable for Australian conditions Safety Wear gloves and eye protection during use Use in well ventilated outdoor areas Store upright in a cool dry place away from direct sunlight Keep out of reach of children Frequently asked questions Can I use it with a pressure washerYes. Pre treat with the recommended dilution, agitate, then rinse with a pressure washer on a low to medium fan setting to avoid surface damage. Will it remove oil stainsIt will lift light oil and grease residue. For deep set oil, use a dedicated degreaser first, then wash with this cleaner. Is it safe on painted wallsYes on most sound exterior paints. Always spot test and avoid prolonged dwell time. What is in the box 1 x Glitz Outdoor Cleaner Concentrate Patio and Wall Wash 2L Why buy from Glues Australia Australian based support and fast dispatch Carefully selected cleaning and maintenance range Advice you can trust for DIY and trade projects
$17.05 $14.18
Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Blast away built up grime, dirt, and weather stains across large outdoor areas with this powerful concentrate. Designed for Aussie backyards, it cuts through tough mess on concrete, pavers, brick, tiles, and timber or composite decks so outdoor spaces look fresh and inviting again. Why you will love it Heavy duty clean that tackles road film, mildew stains, leaf tannins, and greasy marks. Concentrated value so one bottle makes multiple buckets of ready to use solution. Fast results with minimal scrubbing on most surfaces. Versatile for driveways, decks, paths, patios, and outdoor walls. Hose or pressure washer friendly for quick coverage on big jobs. Ideal surfaces Concrete driveways and garage floors Pavers, brick, stone, and outdoor tiles Timber decks and composite decking Rendered walls and fencing Outdoor furniture settings made of hard materials Dilution guide Job type Mix ratio Where to use Heavy build up 1 part cleaner to 4 parts water Oil spots, mildew stains, leaf marks on concrete and pavers General cleaning 1 part cleaner to 10 parts water Routine driveway and deck washes Maintenance 1 part cleaner to 20 parts water Frequent quick cleans and large areas Coverage: A 5L concentrate can make many litres of solution and clean a large area depending on dilution, surface porosity, and soil level. How to use Sweep the area to remove loose debris. Mix to the required ratio in a bucket or pressure washer reservoir. Wet the surface, then apply generously with a garden sprayer, watering can, mop, or pressure washer. Allow 3 to 5 minutes contact time. Do not let the solution dry on the surface. Agitate stubborn spots with a stiff outdoor broom or deck brush. Rinse thoroughly with a hose or pressure washer, pushing residue to drainage. Tips for best results Test on a small hidden patch first to confirm surface compatibility and desired result. Work in the shade on cool surfaces for even cleaning. On timber decks, scrub along the grain and rinse well. Repeat a light application rather than over concentrate for delicate areas. Important information Not recommended for raw or polished natural stone that is sensitive to cleaners. Always patch test first. Avoid use on freshly sealed surfaces. Check sealer instructions before cleaning. Keep runoff away from ponds and delicate plants. Pre wet adjacent garden beds and rinse after cleaning. Safety Wear gloves and eye protection during mixing and application. Ensure good ventilation if using in semi enclosed areas. Store upright in a cool dry place out of reach of children and pets. Specifications Size 5L concentrate Form Liquid cleaner Application Bucket, sprayer, or pressure washer Suitable areas Driveways, decks, patios, paths, outdoor walls What is in the box 1 x Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Frequently asked Will it remove oil stains Heavy oil may require a second application and some scrubbing. For long standing or deep oil, use a degreaser first, then follow with this cleaner for an even finish. Can I use it with a pressure washer Yes. Mix in the detergent tank as per the dilution guide, apply from the bottom up, allow dwell time, then rinse from the top down. Is it safe for sealed decks Patch test first and follow the sealer brand care instructions. Rinse well after cleaning. Good to pair with Outdoor deck brush or stiff broom for agitation Garden sprayer or pressure washer for fast coverage Protective gloves and safety glasses for safe handling
$27.15 $20.89
Keep your surfaces clean with PREP Hospital Grade Lemon Disinfectant. This concentrated, hospital grade formula destroys germs fast and is ideal for general purpose cleaning at home, in offices, and in workplaces. Hospital grade disinfectant with fresh lemon fragrance Concentrated formula for effective sanitising and everyday cleaning Suitable for kitchens, bathrooms, floors, walls, and high touch points Economical, easy to dilute, and simple to use How to Use For hospital grade disinfecting: Dilute 1 part concentrate with 3 parts water (1:3). Apply to pre-cleaned hard, non-porous surfaces. Allow adequate contact time, then rinse if required. For light cleaning: Dilute 250 mL concentrate in 2.5 L water (approximately 1:10). Mop, wipe, or spray, then allow to dry. Rinse food contact surfaces with potable water after use. Where to Use Benchtops, sinks, taps, splashbacks Floors, walls, tiles, grout Toilets, bathrooms, showers Desks, door handles, handrails, shared touch points Good to Know Concentrate makes multiple ready to use bottles from one pack Lemon scent leaves areas smelling fresh after cleaning Versatile for both sanitising and routine maintenance cleans Dilution Guide Application Ratio Example Mix Hospital grade disinfecting 1:3 (concentrate:water) 250 mL + 750 mL water Light cleaning 1:10 (approx.) 250 mL + 2.5 L water Safety Use on hard, non-porous surfaces only Wear gloves for prolonged use and ensure good ventilation Avoid contact with eyes and skin. Do not ingest Keep out of reach of children and pets Specifications Brand Prep Productions Product Type Hospital grade disinfectant concentrate Size 1 Litre Fragrance Lemon Item Weight 1.2 kg Package Dimensions 19 cm x 13 cm x 7 cm Always follow label directions. Test on a small inconspicuous area before first use.
$12.50
Boyle Gloss All in One Glue Sealer and Finish 236 ml Seal, glue and finish your craft projects with a single water based formula that dries clear and glossy. Boyle Gloss All in One is ideal for decoupage, paper craft, school projects and home decor. It brushes on smoothly, holds strongly and leaves a protective shine. Key benefits Three in one formula for gluing, sealing and top coating Gloss finish that dries clear and enhances colours Water based and low odour for indoor use Brushes on easily and levels well Great for beginners and experienced makers Best for Decoupage and collage Paper, card and photos Wood, MDF and craft boards Canvas and fabric accents Lightweight embellishments and mixed media Surface compatibility Use on clean, dry and dust free surfaces. Test on a small area first, especially on delicate papers, prints or dyed fabrics. How to use Prepare: Ensure the surface is clean and smooth. Cut and position your paper or embellishments. Glue: Apply a thin even coat to the surface with a soft brush. Press the item in place and smooth out any bubbles. Seal: After the glue layer sets to tack free, brush a light coat over the top. Allow to dry fully. Finish: Add 1 to 3 additional thin coats for a stronger, glossier finish. Lightly sand between coats if a super smooth result is desired. Dry time and coverage Touch dry in about 15 to 30 minutes depending on coat thickness and conditions Recoat after 30 to 60 minutes Allow 24 hours before light handling. Full cure develops over several days Coverage varies with technique. Thin coats give the best clarity and bond Clean up Wash brushes and tools with warm soapy water while wet Wipe any fresh drips with a damp cloth Tips for a glossy result Apply multiple thin coats rather than one heavy coat Work in one direction for the first coat, then cross coat for the second Use a soft synthetic brush or foam applicator to minimise brush marks Important information For indoor craft use Keep out of reach of children Avoid freezing. Store upright with the cap closed tightly Specifications Type: All in one glue, sealer and finish Finish: Gloss clear Base: Water based Size: 236 ml
$11.00
Davco Davelastic Tile Adhesive Additive 1 L is a reliable latex additive to upgrade cement based tile adhesive performance chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 1 L pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Davco Davelastic for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Davco Davelastic Tile Adhesive Additive 1 L has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Improving bond strength and flexibility Situations where extra deformability is required Wet area tiling as part of a system Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete, screeds, and renders Cement based adhesives and grouts as specified Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of follows the base adhesive behaviour. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Replace all or part of the mixing water with the additive as directed. Observe normal set and cure times for the base adhesive. Temperature and environmental performance Use within the recommended application window of the system you are modifying. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wash tools with water while the mix is fresh. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed. Protect from freezing. Shake before use. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.84
Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gorilla Ultimate for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Furniture build and repair Edge bonding and laminations Cabinetry and joinery where water resistance is valued Suitable surfaces The adhesive works well on the following surface types when properly prepared: Hardwoods and softwoods Plywood and MDF Veneers and end grain with correct technique Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured. Temperature and environmental performance Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$25.20
Key features Dries clear for a neat, invisible finish Non toxic and low odour Water based for easy clean up before curing Suitable for brush or nozzle application Paintable when dry Strong bond on porous surfaces Ideal for Paper, cardboard, photos, and scrapbooking Craft foam, felt, and fabric edge bonding Balsa wood and other light timbers School and hobby projects Directions Ensure surfaces are clean, dry, and free of dust or oil. Apply a thin, even coat to one surface. For very porous materials, coat both surfaces. Join pieces while the glue is wet and press firmly. Clamp or weight if needed. Wipe away excess with a damp cloth. Allow to set. Light handling is typically possible after 30 to 60 minutes. Full strength develops after 24 hours. Clean up Clean tools and fresh spills with a damp cloth. Once cured, scraping or sanding may be required. Handy tips For stronger joints on timber, lightly sand and dry fit pieces before gluing. Avoid excessive glue, which can lead to slow drying and warping on thin paper. Not suitable for continuous water immersion or load bearing joins. Storage Replace cap after use. Store upright in a cool, dry place away from frost and direct heat. Safety Non toxic formula. If irritation occurs, discontinue use. Technical details Base PVA emulsion Appearance White, dries clear Viscosity Medium, smooth flow Open time Up to 10 minutes depending on surface and coat weight Set time Approx. 30 to 60 minutes Full cure 24 hours Water resistance Not recommended for prolonged moisture exposure Paintable Yes, once fully dry
$11.30
Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.
$8.50
Bostik Hobby Craft Dual Tip Liquid Glue 30ml is the perfect choice for creative projects, crafts, and schoolwork. Designed for precision and versatility, this liquid glue features two applicator tips, a fine tip for detailed work and a broad tip for larger surfaces. The smooth, clear formula ensures a clean, professional finish without clumping or streaks. Dual applicator design: Fine and broad tips for all craft needs Clear drying: Leaves no visible residue Ideal for: Paper, cardboard, photos, and light craft materials Easy to use: Non-toxic, washable, and child-friendly Perfect for school and home projects This handy 30ml bottle is compact and easy to store, making it a must-have for hobbyists, students, and anyone who loves crafting. Its dual-tip applicator provides control and convenience whether you're gluing delicate details or covering larger areas. Applications: Arts and crafts, card making, scrapbooking, paper modeling, and DIY projects. Brand: Bostik
$5.88
Power Through Soap Scum & Kill 99.9% of Germs Selleys Complete Clean Bathroom & Shower Spray is a household-grade disinfectant cleaner that cuts through tough soap scum, dirt and grime while killing 99.9% of common bathroom germs (S. aureus and E. coli). Ideal for showers, bathtubs and toilets for a sparkling clean finish. Disinfects effectively: Kills 99.9% of germs (S. aureus & E. coli). Fast soap scum removal: Powers through built-up residue on bathroom surfaces. Household-grade disinfectant: Designed for hard, non-porous bathroom surfaces. Where to Use Suitable for hard, non-porous surfaces such as: showers, bathtubs, toilets and similar bathroom fixtures. Not Suitable For Marble, natural stone, porous tiles or aluminium surfaces Polished, varnished or lacquered surfaces Skin (hard surface disinfectant only) Directions Turn nozzle to ON while directing trigger away from face. Spray directly onto the surface until fully covered. For cleaning: wipe with a clean damp cloth or rinse. For disinfecting: allow 10 minutes contact time, then wipe with a clean damp cloth. On food-contact areas: rinse or wipe with a clean damp cloth after 10 minutes. Good to Know Always test on an inconspicuous area first. Avoid prolonged contact with sensitive surfaces listed above. Keep out of reach of children. Read label before use. Product Details Brand: Selleys Range: Complete Clean Type: Bathroom & shower disinfectant spray Size: 750mL trigger spray
$5.79
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$33.00
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
The Original Super Glue® Corporation's newest product is the ACCUTOOL® . The ACCUTOOL® has a revolutionary, easy to hold design and features high-performance cyanoacrylate. The new ACCUTOOL® precisely applies the product where you want it, how you want it. You can get a continuous stream or drop-at-a-time application based on the amount of pressure you apply to the dispenser buttons. The Original Super Glue®: Fast. Easy. Effective. Pacer Technology Super Glue’s AccuToolTM (19025) is a quick-setting adhesive in a precision applicator that works on oily & dirty surfaces to bond most porous and non-porous materials, such as: Metal Leather Ceramic Wood Fabric Most plastics Porcelain Rubber Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Instructions: NOTE: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$15.50
Original formula Super Glue forms the strongest bonds in tight joints between clean breaks or smooth surfaces. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly and sets in seconds! Packaged in a 20-gram break-away tip bottle this product is ideal for larger projects that require greater amounts of Super Glue. Works best on: Metal Rubber Most Plastics Aluminium Ceramic China Wood Pottery Jewellery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) USE INSTRUCTIONS: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep container pointed away from face and body. Carefully follow opening directions on package. Unscrew cap while keeping container pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before resealing cap securely. Storage: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$12.50
See back of pack photo for indications and description
$12.00
High Performance Future Glue® Brush-On evenly and safely coats most surfaces while eliminating skin contact. Perfect for small and large surfaces needing a thorough coat of Future Glue®. Its instant bonding power can be used for almost all porous and non-porous materials. Its powerful adhesive formula works on dirty, greasy surfaces, and resists high and low temperatures as well as most chemicals. Pacer Technology Super Glue’s Future Glue Brush-On (14204, 15099, 15111) is a quick-setting adhesive that works on oily & dirty surfaces to bond materials, such as: Jewelry Metal Leather Ceramic Most Plastics Rubber Aluminum China Porcelain Hard & soft wood Pottery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820 C) Use: For best results, surfaces should be clean and dry. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. STORAGE AND SHELF LIFE: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$29.95
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40o F to +176oF (-40oC to +80oC) Instructions: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$29.95
Please refer to the photo of the back of the pack for indications and instructions
$15.00
Tarzan's Grip Shockproof Super Glue is a high strength, rubber toughened adhesive that dries clear for a multitude of applications. In addition to offering a superior bond on metals, it is ideal for use with wood, rubber, leather, china, paper and most plastics. It resists extreme temperatures of up to 150C. Sets in around 2 to 3 minutes Impact resistant Heat resistant Superior bond on metals
$10.44
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance. Incredible bond strength Waterproof Adheres to even visibly damp surfaces Fast curing - less than 30 minutes
$10.50
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$15.39
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$25.48
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$22.35
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$44.00
Instant set, low viscosity, multipurpose super glue Suitable for bonding substrates with very smooth surfaces Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood and other materials. It is especially suitable for bonding pieces with very smooth surfaces. Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Characteristics and advantages: One Component Easy to apply, low viscosity Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, leather Low consumption adhesive Versatile allows adhesion between different materials Colourless Durable COLOUR Clear Storage 12 months from date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +5ºC and +25ºC. Refrigeration to +5ºC gives optimum storage stability.
$28.00
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$7.70
Selleys Fibreglass Fix Repair Kit is a complete kit containing polyester resin, a hardener and fibreglass mat, for repairs to fibreglass and a variety of other surfaces. Where can this product be used? Boat repairs including hull repairs Surfboard / Surfski repairs Automotive repairs Repairing a leaky gutter Patching downpipes Patching metal roofs or grass catchers Not approved for contact with drinking water What materials is this product suitable for? Fibreglass Plywood Metal Fibro Sheeting Most Plastics How to use this product Wear rubber or plastic gloves when handling fibreglass Surface Preparation Surfaces should be clean and dry and free from paint, grease and rust. Cut the fibreglass mat to shape, allowing approximately 3cm overlap all round. Tease out the fibres along the edge of the mat to give a feathered edge. For wide holes, glue a piece of cardboard to the back of the hole to form a base. Mixing: For each tablespoon of resin, squeeze 5 drops of hardener from the small tube and mix together thoroughly. Do not prepare the mixture until required as only a limited time (20 minutes at 20°C) is available before the product gels. Application Position the mat and apply resin/hardener mixture with a clean, dry brush. Be sure to impregnate the mat completely, working out all air bubbles. Add more mat and resin/hardener mixture to build up or contour the patch as required. Finishing When the patch has completely hardened, (approximately 1-2 hours, depending on the temperature), it can be sanded to a smooth finish. Fill imperfections with more resin. Paint if required. Clean up product with Solvent Acetone before it cures Handy tips At higher temperatures, the working time decreases. Can only be tinted with iron oxide or other dry pigments .which must be mixed in very thoroughly. Surfaces to be joined should be clean and dry. If recommended amounts of hardener are not used, cure time will vary or an incomplete cure may result. A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). In large amounts, heat can be generated during cure. Care should be taken on heat-sensitive surfaces with large amounts. Use recommended levels of hardener and resin; variation may result in incomplete cure and variations in cure time. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Features Non-corrosive Weather resistant – resistant to water, weather or marine growth Rapid setting Impact resistant – can take knocks Sandable – can be sanded after 1-2 hours Can be painted over Extended working time – up to 20 minutes at 20°C Dries Opaque Heat resistant to 100°C
$41.01
You have seen 96 out of 183 products
Bottled adhesives with precision tips for controlled dots and lines on assemblies and crafts. Common choices include PVA wood glues and cyanoacrylates for quick bonds. Match open time and clamp needs to your project; store upright and avoid contaminating the tip. Use filters to refine by chemistry, cure speed and temperature rating. Always consult the product page and TDS/SDS.
