SikaSeal® Kitchen and Bathroom SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Uses Glass and enamel Ceramics and tiles Aluminium, steel, zinc, copper Plastic laminates Rubber Stainless steel Concrete and grouts Characteristics / Advantages Excellent adhesion Great weatherability Non-sag Great tooling characteristics Long-term mould resistance Interior and exterior usage Fast curing Colours White Beige Black Charcoal Transparent Alabaster Almond Ivory Off White Stone Pewter Grey Mid Grey Stone Brown Packaging 300ml cartridges, 12 cartridges per box Shelf Life 12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base: Neutral curing Density: 0.98 g/cm³ @ 23ºC Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h. Curing Rate: 72 hours @ 23ºC/50% r.h. Consistency: Non-sag Mechanical/Physical Properties Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h. Shore A Hardness: 20 SHA E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h. Ultimate Elongation: 300% Anti-mildew Property: 0 level
$14.00 - $17.33
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/add6c9293f9448a0b56570405080097d.jpg?v=1757756088&width=645)
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. SafetyTips Uncured product may irritate eyes. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Refer to the Safety Data Sheet (SDS) for full details.Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$16.00 - $20.16
Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.
$20.15 - $20.18$0.03/g
Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.
$70.50
Selleys Wet Area Silicone is a high-quality, neutral cure silicone sealant designed specifically for areas exposed to moisture, such as kitchens, bathrooms, and laundries. This 100% silicone formula provides a long-lasting waterproof seal that won’t shrink, crack, or peel for up to 25 years, making it ideal for sealing around showers, sinks, bathtubs, and other wet areas. Its anti-mould properties ensure that your bathroom stays hygienic and clean for longer. The 90ml tube is perfect for smaller jobs or touch-ups, offering easy handling for precise application in tight spaces. Selleys Wet Area Silicone adheres to a wide range of materials, including ceramics, glass, stainless steel, metal fittings, and plastic laminates, ensuring a secure, flexible seal in high-humidity environments. Whether you’re sealing around a kitchen sink or maintaining the edges of a shower enclosure, this product guarantees professional results every time. Where can this product be used? Showers screens Baths Spas Sinks Plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Clean surface with mineral turpentine and dry. Cut cartridge, fit and cut nozzle at 45° angle and fit into a caulking gun. Apply with steady pressure, ensuring sealant is pushed into joint. Tool with a spatula dipped in detergent water within 5-10 mins of application. Clean up with mineral turpentine before product skins. Sealant will cure in 72hrs. Limitations: Not paintable. Complete painting 7 days prior to applying sealant. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. Not suitable for aquariums. Not suitable for food or drinking water contact. Not suitable for permanent water immersion. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. *Warranty Information Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$13.62
Selleys Rapid Mould Killer is a fast-acting spray that tackles stubborn mould and mildew in and around the home. Formulated for busy bathrooms, laundries and other damp, mould-prone areas, it gets to work almost immediately, destroying visible mould in as little as 30 seconds and eliminating 99.9% of germs on treated surfaces. The 750ml trigger pack delivers plenty of product for larger jobs, with a twist nozzle that switches between a fine spray and a targeted stream. Key features Effectively eradicates stubborn mould and mildew Fast acting – destroys visible mould in around 30 seconds Eliminates 99.9% of germs on hard surfaces Adjustable spray/stream trigger nozzle for controlled application Generous 750ml size for larger and more frequent jobs Where to use it Indoors: Ideal throughout the bathroom and laundry – on tiles and grout, shower screens, shower curtains, toilets, rubber bath mats, plastic surfaces and other mould-affected areas. Outdoors: Suitable for spot-treating mould-affected exterior surfaces where staining and mould have taken hold. How to use Twist the nozzle to either SPRAY or STREAM. Spot test on an inconspicuous area first. Spray directly onto the mould-affected surface. Leave for about 30 seconds, then rinse, wipe or scrub off. Important notes On some matt-finish tiles or in hard-water areas, staining may occur – always patch test first. Not suitable for fabric, mirror tiles, metallic surfaces, or older baths and basins. Do not mix with other cleaners. Specifications Brand Selleys Product Rapid Mould Killer Size 750ml Format Ready-to-use trigger spray Action Destroys mould in ~30 seconds; kills 99.9% of germs Best for Bathrooms, laundries, toilets and other mould-prone areas Suitable surfaces Tiles, grout, shower screens, shower curtains, plastic, rubber bath mats Safety This is a bleach-based (sodium hypochlorite) mould killer. Use in a well-ventilated area and wear suitable gloves and eye protection. Avoid contact with skin, eyes and clothing. Never mix with other cleaning products or acids, as hazardous chlorine gas can be released. Keep out of reach of children, rinse treated surfaces after use, and store upright in a cool place away from direct sunlight. Always read the label and refer to the manufacturer’s Safety Data Sheet before use.
$10.79
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-wet-area-bathroom-kitchen-sealant-90ml-clear-2.jpg?v=1792406361&width=645)
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout) The product also contains fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour so can be used in any environment without discomfort. Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam. Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. Temperature resistance – approximately -60°C +150°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Where can this product be used? Showers and sinks. Metal, copper and brass fittings. Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper and brass fitiings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal. Handy tips Tips for Using a Silicone Sealant in a Wet Area Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safetytips Uncured product may irritate eyes. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$13.62
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-sealant-waterproof-white-2.png?v=1792406184&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$23.83
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
Selleys White For Life Ready To Use Grout is a premium-quality, pre-mixed grout designed to deliver a brilliant, long-lasting white finish for wall and floor tiles. Suitable for interior applications with joints up to 5mm, this product is ideal for both new tile installations and regrouting jobs. Surface Preparation: Ensure all surfaces are clean, dry, and free from dust, oil, old grout, and other contaminants. For new tiling jobs, let tile adhesive set for at least 24 hours. For regrouting, completely remove old grout and thoroughly clean the joints. Application Instructions: Cut the cartridge tip and attach the nozzle. Trim to desired bead width. Using a caulking gun, apply grout into joints, pressing it in to eliminate air gaps. Smooth grout using a rubber float or grout applicator, working diagonally. After 15–20 minutes (depending on temperature), gently wipe tile surfaces with a damp sponge to remove excess grout and haze. Avoid over-wetting and excessive wiping, which can weaken the grout lines. After 24 hours, polish tile surfaces with a soft dry cloth to remove any remaining haze. Coverage: Approx. 2m² per 410g cartridge (based on 300x300mm tiles with 3mm x 5mm joints) Drying Time: Touch dry in 30 minutes Allow 72 hours before exposing to water in wet areas such as showers Clean-Up: Clean tools and tile surfaces with water before the grout cures Once dry, remove excess grout by mechanical means Technical Data: Colour: White Appearance: Smooth, creamy paste Joint Width: Up to 5mm Water Clean-Up: Yes (before curing) Shelf Life: 12 months if stored unopened in a cool, dry place
$19.72
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.80
Dunlop Ready-to-Go Tile & Grout 250g (White) is a clever 2-in-1 product that works as both a tile adhesive and a grout, straight from the tube. There is nothing to mix and very little mess, which makes it a go-to for small tiling jobs, mosaics and quick repairs or touch-ups around the home. Backed by Dunlop's 10 year guarantee. 2-in-1 ready-to-use tile adhesive and grout No mixing, no fuss, less mess Contains Grout Shield antifungal protection Ideal for mosaics, repairs and touch-ups Suitable for joint widths of 1-5 mm Indoor and outdoor wall use About the formula This white, pre-mixed paste bonds wall tiles and then fills the joints with the same material, so a single tube handles the whole repair. The built-in Grout Shield technology helps resist mould and bacteria, keeping finished joints looking cleaner for longer. Excess can simply be wiped away with a damp cloth while still fresh, and the resealable tube makes it easy to store for future touch-ups. Where to use it Indoors: wall tiles and mosaics in kitchens, splashbacks, laundries and living areas, plus general tile and grout repairs. Suitable over concrete, cement render, fibre-cement sheet, plasterboard and prepared painted surfaces. Outdoors: exterior wall tiles and mosaics. When grouting outdoors, protect the area from extremes of weather for 7 days while it cures. Tile types: ceramic, porcelain and marble wall tiles and mosaics (excluding moisture-sensitive stone). How to use it Prepare the surface so it is flat, firmly fixed, clean and dry, free of dust, oil, grease and loose material. Prime surfaces with Dunlop Primer & Additive and allow to dry. Spread the adhesive with a 4.5-6 mm notched trowel to a minimum 1 mm bed. Press and slide each tile into position for full contact, adjusting within 60 minutes (at 23°C, 50% humidity). Joints can be grouted immediately. Squeeze the material firmly into the joints and compact with a grout float or squeegee, scraping off excess from the tile face. After about 15 minutes, wipe back excess with a damp, small-pored sponge, rinsing often. Once the joint has hardened (approx. 6-24 hours), buff and polish the tiles with a clean, dry cloth. Important notes Not suitable for use in wet areas such as a shower recess, over Dunlop Waterproofing membrane, or in continuously immersed conditions. Do not use the grout in expansion or movement joints. For textured or matt tiles, test ease of cleaning on a spare tile first. Designed for wall tiles and mosaics rather than heavy floor tiling. Specifications Brand Dunlop Product Ready-to-Go Tile & Grout (2-in-1) Colour White Size 250 g Form Pre-mixed, ready-to-use paste Tile types Ceramic, porcelain, marble, mosaics (excl. moisture-sensitive stone) Surfaces Walls Location Indoor and outdoor Joint width 1-5 mm Clean up Water (while fresh) Guarantee 10 year (Ardex Australia) Safety Causes skin irritation and may cause an allergic skin reaction. Causes serious eye damage and may cause respiratory irritation. Use only outdoors or in a well-ventilated area, and wear protective gloves, clothing, eye and face protection. Avoid breathing any mist, vapour or spray. Refer to the Safety Data Sheet (SDS) for full details.
$16.88
Glitz Daily Shower Cleaner Prevents Soap Scum Build Up 750ml Keep your shower looking fresh with this easy daily spray. Glitz Daily Shower Cleaner helps prevent soap scum and mineral build up so glass, tiles, and fittings stay clearer for longer. No heavy scrubbing required. Just spray and go as part of your routine. Key benefits Helps stop soap scum forming between deep cleans Cuts through light residue from body wash and shampoo Streak free finish on shower screens when used as directed Fast application for busy bathrooms Fresh clean scent that leaves the space smelling pleasant Where to use Shower glass and screens Ceramic tiles and grout surrounds Fibreglass and acrylic bases Chrome and stainless steel fittings Sealed stone and laminate surfaces in wet areas Always test first on an inconspicuous spot. Avoid unsealed stone, marble that is not sealed, brass, copper, and any surface that is not water safe. How to use After showering, quickly rinse surfaces with warm water. Set nozzle to spray. Mist evenly over glass, tiles, and fittings. Leave to work. No rinse required on light residue. For heavier build up, wipe with a soft cloth or squeegee. Use daily to help prevent soap scum returning. Pro tips Keep a squeegee in the shower and pull down glass before spraying for the best clarity. Ventilate the bathroom to reduce fogging and moisture marks. Pair with a weekly deep clean for grout lines and corners. Good to know Non abrasive formula suitable for regular use Safe for most sealed surfaces when used as directed Family friendly routine cleaner for shared bathrooms Specifications Product Daily shower maintenance spray Size 750 ml trigger bottle Suitable surfaces Glass, ceramic tile, acrylic, fibreglass, chrome, stainless steel, sealed stone Finish Clear streak free when wiped or squeegeed Use frequency Daily after showering Safety Read label before use. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other cleaners. Store upright in a cool dry place. Frequently asked questions Do I need to rinse after spraying For light daily residue, no rinse is needed. For visible build up, wipe or squeegee for a clear finish. Will it remove heavy limescale It is designed to prevent and control light residue. For stubborn limescale, use a suitable descaler first then maintain with daily use. Is it safe on natural stone Use only on sealed stone. Test first and avoid unsealed or delicate stone surfaces. What is in the box 1 x 750 ml Glitz Daily Shower Cleaner with adjustable trigger
$11.61 $11.28
Protite Mould Defender Anti-Fungal Paint Additive 75 mL is a reliable liquid paint additive that helps inhibit mould growth in humid areas chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 75 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Protite Mould for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Protite Mould Defender Anti-Fungal Paint Additive 75 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms and laundries Kitchens and food prep zones Rental refresh and maintenance work Suitable surfaces The adhesive works well on the following surface types when properly prepared: Walls and ceilings coated with water based paint Suitable primers as per paint maker guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of Work to normal paint tray timelines. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix thoroughly into your chosen paint and apply as directed by that paint. Dry and recoat times follow the paint system. Temperature and environmental performance Use within the temperature window recommended for the host paint. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean rollers and brushes according to the paint manufacturer's advice. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store upright with cap tight. Do not allow to freeze or overheat. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.64
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$24.57
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
![Selleys No Mould Silicone Selant 100ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-selant-100ml-white-2.png?v=1792406202&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
![Selleys No Mould Silicone Selant 100ml [Translucent] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-selant-100ml-translucent-2.png?v=1792406193&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-more-gaps-filler-bathroom-and-kitchen-white-2.jpg?v=1792406110&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$14.99
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$9.33
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$185.00
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.61
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
![Monarch Mini Silicone Mould Resistant [Translucent] (2)](http://gluesaustralia.com.au/cdn/shop/files/monarch-mini-silicone-mould-resistant-translucent-2.png?v=1792405534&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$6.28
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Crommelin Silicone WP Plus is a neutral cure silicone sealant made for wet areas, and it doubles as a bond breaker in Crommelin liquid applied waterproofing systems. This white 300g cartridge suits kitchens, bathrooms, laundries and similar jobs. It stays permanently flexible once cured and contains a mould and mildew inhibitor, so it holds up well in damp, steamy spaces.About the formulaA one-part, neutral cure silicone, so there is no mixing. The neutral cure chemistry will not corrode concrete or zinc coated and galvanised steel. It has a sag resistant body that can be used in vertical and overhead joints. Once cured it resists weathering, UV and vibration, and it is suitable for contact with aluminium shower screens. It can be used as a bond breaking sealant at joints, junctions and corners under waterproofing membranes, or as a durable finishing sealant.Where to use itIndoors: around showers, bath tubs, sinks, laundry fixtures, sanitary ware and spas, plus bond breaking joints in wet area waterproofing.Outdoors: exterior finishing joints and roof and gutter sealing, where the sealant is exposed to weather.Suitable materials include glass, glazed tiles and ceramics, steel and aluminium (suitably prepared), concrete, render, brickwork and blockwork, natural stone, fibre cement sheet and plasterboard. Use it only on clean, sound surfaces.How to use itMake sure the joint is clean, dry and free of dust, grease, soap residue and loose material. Cut the nozzle to suit the joint size, load the cartridge into a caulking gun and apply a continuous bead, then tool it smooth. Where it is used as a bond breaker in a waterproofing system, apply it at all joints, junctions, angles and internal corners before the membrane goes on. Refer to the Crommelin technical data sheet for full application guidance.Important notesThe cured silicone is not paintable, and it should not be used on freshly painted surfaces. Do not use it where it will contact food or potable water. Avoid materials that bleed oils, plasticisers or solvents, because they can affect adhesion. Keep it away from the silver backing of mirrors, such as at mirror edges. It is not a fire rated sealant. Silicone needs moisture in the air to cure, so it will not cure in a sealed, moisture-free environment.Specifications Brand Crommelin Product Silicone WP Plus (Silicone & Bond Breaker) Pack 1 x 300g cartridge (300ml) Colour White Base Neutral cure silicone, one part Application Cartridge, via caulking gun Features Mould and mildew resistant, permanently flexible, UV and weather resistant, sag resistant Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses where sensible. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$16.71
Soudal Bathroom & Kitchen Neutral Cure Silicone in clear is a pure silicone sanitary sealant for wet areas, supplied as a 300ml cartridge for use in a standard caulking gun. It is built for the joints that take the most punishment around showers, baths, sinks and benchtops, giving a waterproof seal that stays flexible and resists mould and mildew.About the formulaA neutral cure, non-corrosive silicone made from pure silicone with no extenders. It contains fungicides to help the seal resist mould and mildew in demanding sanitary conditions. It is easy to apply and tool, has a longer working time for smoothing joints, and stays permanently elastic once cured. The cured seal is colourfast and UV resistant, with a low modulus and a joint movement capability of +/- 25%.Where to use itIndoors: joints around bathtubs, vanities, shower screens, sinks, basins and toilets, kitchen splashbacks and benchtop joints, and sealing around plumbing fixtures in kitchens, bathrooms and laundries.Outdoors: not specifically recommended by the manufacturer for this product. Check the manufacturer data sheet or choose a product made for exterior use.Suitable materials include glass, tiles, fibreglass, vitreous enamel and many other common building and sanitary surfaces. Test an inconspicuous area first on any surface you are unsure about.How to use itMake sure the joint is clean, dry and free of dust, grease, soap scum and old sealant. Cut the nozzle to suit the joint, load the cartridge into a caulking gun and apply a steady, continuous bead. Smooth the bead with a profiling tool or a soapy water solution before the surface skins over, then remove any masking tape. Wipe away uncured excess promptly. Once cured, silicone has to be cut or scraped away.Important notesCure time depends on temperature, humidity and bead thickness, so allow plenty of time before exposing the joint to water. Keep joints well ventilated while curing. Always follow the manufacturer's instructions and test compatibility on sensitive materials before sealing.Specifications Brand Soudal Product Bathroom & Kitchen Neutral Cure Silicone Pack 300ml cartridge Colour Clear Base 100% silicone, neutral cure, no extenders Application Cartridge, via caulking gun Movement capability +/- 25% Key features Mould resistant, waterproof, non-corrosive, colourfast and UV resistant Use Bathrooms, kitchens and other wet areas SafetyWash exposed skin thoroughly after handling and wear suitable gloves and eye protection. Store locked up and dispose of contents and container in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$10.38
The Fix-It-Fast Roof Repair Kit for Metal Roofs & Gutters is a ready-to-go patch kit for stopping leaks in metal roofing and gutters, with everything needed for the repair packed together in one tube. It pairs a self-adhesive Smartform flashing patch with a brush-on Wet Shield compound, so a homeowner can seal a leak in roughly five minutes without specialist tools or a tradie callout.About the formulaThe kit is a three-part system: a 300mm x 300mm Smartform patch, a 125g tub of Fix-It-Fast Wet Shield and an application brush. Smartform is an ultra-thin, flexible flashing with an aluminium surface and a butyl backing, and it can stretch by up to 60% so it can follow corrugated and irregular metal profiles. Wet Shield is a resin-based, fibre-reinforced, solvent-based repair compound. It is brushed around the edges of the patch to help stop water tracking underneath and lifting it. It can be applied to wet or damp surfaces, bridges small cracks, dries to a flexible membrane that resists algae and fungal growth, and needs no primer on sound, non-porous surfaces.Where to use itIndoors: not intended for interior use.Outdoors: patching leaks, splits and failed joins in metal roof sheeting (including corrugated and Colorbond profiles), gutters and valleys, and sealing around damaged flashing. It suits both residential and commercial maintenance jobs.Designed mainly for metal roofing and gutters. For tiled roofs, Fix-It-Fast makes a separate Tile Roof kit with a reinforced Dakaflash patch.How to use itClear loose debris, dirt, moss and algae from the repair area so the surface is sound and clean. Position the self-adhesive Smartform patch over the leak and press it down firmly so it conforms to the roof profile. Then brush Wet Shield around all the edges of the patch, overlapping onto the surrounding roof, to seal the perimeter and protect it from uplift. Once the Wet Shield has fully cured, it can be painted with an outdoor water-based acrylic paint if you want the repair to blend in. Keep the tub closed when not in use and follow the instructions supplied in the pack.Important notesA patch repair cannot fix a roof that is structurally unsound or unstable, so secure loose sheets and fixings first. The kit is built for localised repairs; for larger areas, Fix-It-Fast also sells flashing in longer lengths and Wet Shield in larger tins. Cure and recoat times are not confirmed here, so check the pack instructions. Wet Shield is solvent-based, so apply it in a well-ventilated outdoor area and keep it away from ignition sources.Specifications Brand Fix-It-Fast Product Roof Repair Kit for Metal Roofs & Gutters Pack 1 kit (patch, Wet Shield tub, brush) Patch Smartform flashing, 300mm x 300mm Patch stretch Up to 60% Wet Shield 125g tub Wet Shield base Resin-based, fibre-reinforced, solvent-based Application Self-adhesive patch plus brush-applied Wet Shield Pack dimensions Approx. 72mm x 72mm x 320mm tube Use Outdoor, residential and commercial SafetyThe Wet Shield in this kit is classified as a flammable liquid (Category 3) that may cause drowsiness or dizziness and is harmful to aquatic life with long-lasting effects. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Avoid breathing the vapours and wear protective clothing and eye and face protection. Do not eat, drink or smoke while using it, and wash hands after use. Refer to the Safety Data Sheet (SDS) for full details.
$44.59
Gyprock Wet Area Acrylic Sealant is a white, paintable acrylic sealant made for bathrooms, laundries and other wet area builds, supplied here as a single 450g tube. It is designed to give plasterboard and wet area linings a long-lasting, flexible seal where they meet shower bases, baths and plumbing fittings, and it also works as a general purpose gap filler.About the formulaA ready-to-use acrylic sealant that stays flexible once cured, so it can move with the joint instead of cracking. It contains an antifungal agent to help resist mould and mildew, and it has moisture resistant properties for use in damp rooms. It can be painted over once fully cured. It is manufactured in Australia for CSR Gyprock.Where to use itIndoors: sealing the edge of Gyprock Aquachek wet area lining against pre-formed shower bases and baths, sealing around plumbing penetrations and fittings, and filling general gaps and junctions in bathrooms, laundries and other damp areas.It suits both residential and commercial construction. It is intended for non-fire-rated wet area systems.Suitable materials include Hebel, concrete, masonry, brickwork, plasterboard, fibre cement, metal, timber and plastic substrates (test plastics on a small area first).How to use itMake sure the joint or gap is clean, sound and free of dust, grease and loose material before you start. Cut the nozzle to suit the size of the joint, run a continuous bead and press it into the gap so it contacts both sides. Smooth the joint, and keep your tools clean while you work. Let the sealant cure fully before you paint over it. Unopened tubes should be kept in a cool, dry place away from direct sunlight and below 30°C. Opened tubes may skin over near the opening, so discard any lump or skin and the remaining sealant can still be used.Important notesThis sealant is not designed for constant water exposure or for stopping active leaks. Do not paint until it is fully cured. It is not an easy-sanding product. Shelf life is 1 year from the date of manufacture. The manufacturer does not publish set, cure or coverage figures for this tube, so allow plenty of time before showering or painting and check the label for current directions.Specifications Brand Gyprock (CSR) Product Wet Area Acrylic Sealant Pack 1 x 450g tube Colour White Base Acrylic Application Tube, used with a caulking gun Specific gravity Approximately 1.55 VOC content 17g/L (as specified by GBCA) Shelf life 1 year from date of manufacture Paintable Yes, once fully cured Use Wet area sealing and general purpose gap filling Origin Made in Australia SafetyIn a fire, use carbon dioxide, foam, dry chemical or water spray, and note that heated decomposition may release carbon dioxide and acrid smoke. Store unopened tubes in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$17.77
![Fastfix Wet Shield One Coat Instant Waterproofing 2.5kg [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/fastfix-wet-shield-one-coat-instant-waterproofing-2-5kg-grey-2.jpg?v=1792410637&width=645)
Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$89.91
Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$37.54
Selleys Grout Stain Whitener is a water-based treatment that restores tired, discoloured grout to a clean, even white. Rather than simply scrubbing the surface, it coats the grout line to mask stains from mould growth, ingrained dirt, spilt makeup or hair-dye, leaving tiled areas looking fresh and bright again. It can also be used to recolour grey or other coloured grout to white. The formula contains a built-in fungicide that creates a protective barrier, making it harder for mould spores to take hold and for new stains to penetrate the grout, helping to break the mould cycle and keep grout looking cleaner for longer. It is supplied in a 280g tube fitted with a foam applicator tip for neat, controlled application straight onto the grout line. Where to use it Indoor: Tiled walls and floors in bathrooms, kitchens and laundries. Suitable for use on cement-based grout between ceramic and porcelain tiles. This is an interior-use product and is not intended for outdoor application. How to use Clean the tiled area and grout thoroughly and allow it to dry completely. Wearing gloves, an apron and old clothing is recommended. Press the foam applicator firmly against the grout and apply even pressure to the tube while moving the applicator along the grout lines. Allow to dry for at least 30 minutes, then check by wiping over with a damp cloth. If not yet dry, allow more time (no more than 2 hours). Once dry, remove excess with a lint-free damp cloth or sponge, wiping diagonally across the grout line. Reapply anywhere too little product was applied or too much was wiped off. After use, rinse the sponge under a downward-tilted tap, blot dry, and replace the lid firmly until next use. Allow at least 5 hours before the treated area is exposed to water. Important notes Do not use on unglazed or porous tiles and stone. Not recommended for tiles with intricate patterns or grooves from which the product may be difficult to remove. Heavily stained or coloured grout may need two applications. For longer-lasting protection, avoid harsh, abrasive cleaning of treated grout lines. Uncured product cleans up with water; cured product can be softened with methylated spirits. Specifications Brand Selleys Size 280g tube Colour White Technology Water based Use Interior Suitable surface Grout Application Foam applicator tip SafetyKeep out of reach of children. Avoid contact with eyes and prolonged contact with skin; wear gloves during use and wash hands after handling. Use in a well-ventilated area. Refer to the Safety Data Sheet (SDS) for full details.
$20.51
Endeavour Timber Deck Cleaner is the preparation step before oiling any deck, new or old. It is a triple-action, water-based cleaner from Prep Productions' Endeavour range that cleans away grime, grease, mould, algae and mildew, restores stained and dirty boards to sound timber, and rejuvenates grey, weathered decks so they brighten back towards their natural colour. On new boards it strips out natural tannins, helping your decking oil penetrate evenly and last longer. The 4 litre pack is sized for full decks and repeat seasonal cleans.Formula overviewA water-based solution whose two key actives work together: oxalic acid brightens the timber and lifts tannin staining, while benzalkonium chloride, a biocide, deals with mould, algae and mildew. The concentrate is a pale, clear liquid that dilutes in water for application.Where to use itOutdoor: all new and weathered exterior timber, with decks the headline use. Also suited to preparing other exterior timber surfaces before finishing.Indoor: not intended for interior surfaces. This is an exterior timber preparation product.How to use Dilute with water as directed on the pack label. Apply the diluted solution with a deck scrub, working it into the boards. Rinse thoroughly and allow the timber to dry before oiling. Follow the label for contact time and drying guidance. Coverage is 5 to 10 square metres per litre when diluted, depending on timber porosity and texture. Important notes This is a Schedule 6 poison. Store it tightly closed, away from children and pets. Wear gloves and protective clothing: the concentrate is harmful in contact with skin and if swallowed. Prevent runoff entering drains, garden beds or waterways, and rinse surrounding plants with water if splashed. May settle on standing; stir before use. Specifications Size 4 litres Base Water-based, oxalic acid and benzalkonium chloride actives Coverage 5 to 10 m² per litre diluted Application Deck scrub Clean up Water Made in Australia SafetyWear rubber or nitrile gloves and eye protection, avoid contact with skin, eyes and clothing, and do not eat, drink or smoke while using. For skin contact, wash with warm soapy water for 10 to 20 minutes and remove contaminated clothing; for eyes, flush with lukewarm water and seek advice if irritation persists. Not flammable. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.95
Endeavour Timber Deck Cleaner is the preparation step before oiling any deck, new or old. It is a triple-action, water-based cleaner from Prep Productions' Endeavour range that cleans away grime, grease, mould, algae and mildew, restores stained and dirty boards to sound timber, and rejuvenates grey, weathered decks so they brighten back towards their natural colour. On new boards it strips out natural tannins, helping your decking oil penetrate evenly and last longer.Formula overviewA water-based solution whose two key actives work together: oxalic acid brightens the timber and lifts tannin staining, while benzalkonium chloride, a biocide, deals with mould, algae and mildew. The concentrate is a pale, clear liquid that dilutes in water for application.Where to use itOutdoor: all new and weathered exterior timber, with decks the headline use. Also suited to preparing other exterior timber surfaces before finishing.Indoor: not intended for interior surfaces. This is an exterior timber preparation product.How to use Dilute with water as directed on the pack label. Apply the diluted solution with a deck scrub, working it into the boards. Rinse thoroughly and allow the timber to dry before oiling. Follow the label for contact time and drying guidance. Coverage is 5 to 10 square metres per litre when diluted, depending on timber porosity and texture. Important notes This is a Schedule 6 poison. Store it tightly closed, away from children and pets. Wear gloves and protective clothing: the concentrate is harmful in contact with skin and if swallowed. Prevent runoff entering drains, garden beds or waterways, and rinse surrounding plants with water if splashed. May settle on standing; stir before use. Specifications Size 1 litre Base Water-based, oxalic acid and benzalkonium chloride actives Coverage 5 to 10 m² per litre diluted Application Deck scrub Clean up Water Made in Australia SafetyWear rubber or nitrile gloves and eye protection, avoid contact with skin, eyes and clothing, and do not eat, drink or smoke while using. For skin contact, wash with warm soapy water for 10 to 20 minutes and remove contaminated clothing; for eyes, flush with lukewarm water and seek advice if irritation persists. Not flammable. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$13.95
Say goodbye to musty smells and damp cupboards. Prep Marathon Dehumidifier Refill Bag 350g pulls excess moisture from the air to help stop mould spots, condensation, and stale odours. It is simple, quiet, and requires no power. No special container required Use it with what you already have at home. Just pour a portion of the crystals into a small open container such as a ramekin, takeaway tub, or jar without the lid. Place the container where you need moisture control and let the crystals do the work. You do not need a branded canister or a hanging device. Why customers choose this refill Instant setup with everyday containers Fast moisture capture that helps reduce foggy windows and damp smells Quiet and power free for wardrobes, pantries, bathrooms, and storage tubs Flexible use split one bag across several small spaces Great value cost effective way to freshen multiple areas Quick start guide Choose a small open container. Keep it clean and dry. Pour in 2 to 4 tablespoons of crystals. Start small and add more if the area is very damp. Place the container on a stable, upright surface in the target area. Check weekly. When the crystals dissolve and liquid forms, empty responsibly and top up with fresh crystals. Repeat until you have the dryness you want. Store the remainder in a sealed bag or jar. Where it works best Wardrobes and linen cupboards Laundries and bathrooms with limited ventilation Pantries, shoe cabinets, and storage tubs Caravans, boats, sheds, and garages Spare rooms and rentals that sit closed for long periods Results you can expect Fresher smelling fabrics and stored items Less condensation on windows and walls More comfortable, drier small spaces Tips for best value Use several small containers instead of one large one for faster results. Place near the source of damp, such as behind closet doors or under sinks. In very humid weather, refresh more often for consistent performance. What you get 1 x 350 g bag of moisture absorbing crystals Enough to treat multiple small containers around the home Safety and care Keep out of reach of children and pets Do not ingest. Avoid contact with eyes and skin If contact occurs, rinse with plenty of water Dispose of used liquid and crystals according to local council guidelines Store unused crystals in a sealed container in a cool dry place Specifications Brand Prep Marathon Type Moisture absorber refill crystals Net content 350 g Power requirement None Typical duration Up to 1 to 3 months per container, varies with humidity Suitable areas Wardrobes, cupboards, pantries, bathrooms, caravans, boats, storage tubs Make it work for you Buy one for the wardrobe and split the rest between the pantry, bathroom, and shoe cabinet. Small top ups keep everything fresh and dry without buying any extra gear.
$12.50 $9.00
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. SafetyTips Uncured product may irritate eyes. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Refer to the Safety Data Sheet (SDS) for full details.Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$51.50
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*. Provides superior water resistance, mould and soap scum resistance White For Life – Always looks like new* Resists yellowing, staining and blackening* Crack resistant Sand free - resists scratching files Suitable for indoor wall and floor tiles Comes in a cartridge for minimum wastage Where can this product be used? Bathrooms Showers (walls only) Toilets Laundries Kitchens What materials is this product suitable for? Ceramic tiles Porcelain tiles Stone tiles Most other tiles Please contact your store to confirm avaliability, as some stores may have a limited range. How to Use Preparation For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult. Application Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time. Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint. Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets. Allow grout to firm up in joints for approx 20 min (longer in colder conditions). Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints. Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks. overage 1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm). 1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm). Limitations: Not for areas frequently immersed in water eg. Shower floors. Allow to dry for 3 days before exposing grout to water on shower walls. Handy tips If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas. *To maintain whiteness and long term stain & mould resistance: Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard. Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners. Areas subject to high foot traffic will require frequent cleaning. Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes. Coverage guide 1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm) 1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm) Clean Up Clean up tools with water before product hardens. Uncured product may be removed with water.
$34.00
![Selleys Wet Area Silicone Sealant Speed Seal 1 Hour [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697122629_597e18e6-75e4-42a2-a468-6311b7fae1b1.jpg?v=1754711756&width=645)
$18.00
![Selleys Wet Area Sealant EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens. Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away Mould resistant Precision application for the best finish Where can this product be used? Showers Baths Spas Sinks Metal, copper and brass plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Powder coated aluminium Aluminium Plastic laminates Rubber Glass Stainless steel Concrete Size 100g Aerosol can Technology Neutral Cure Silicone Use Interior How to Use Use in a well ventilated area. Avoid contact with skin and eyes. 1. Throughly clean and dry surface from oil, dirt and grease with mineral turps. 2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. 3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap 4. Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Sealant is not paintable.Complete painting 7days prior to applying sealant. • Not for aquariums or contact with food, eating utensils or drinking water.
$14.77
![Selleys Wet Area Sealant EZI Press [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens. Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away Mould resistant Precision application for the best finish Where can this product be used? Showers Baths Spas Sinks Metal, copper and brass plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Powder coated aluminium Aluminium Plastic laminates Rubber Glass Stainless steel Concrete Size 100g Aerosol can Technology Neutral Cure Silicone Use Interior How to Use Use in a well ventilated area. Avoid contact with skin and eyes. 1. Throughly clean and dry surface from oil, dirt and grease with mineral turps. 2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. 3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap 4. Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Sealant is not paintable.Complete painting 7days prior to applying sealant. • Not for aquariums or contact with food, eating utensils or drinking water.
$21.37
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/b491df0a1d2e4750abba298eed7eeb4d.jpg?v=1757753045&width=645)
![Selleys No Mould Silicone Sealant Waterproof [Translucent] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-sealant-waterproof-translucent-2.png?v=1792406175&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$20.00
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$15.16
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$13.35
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$22.18
Long-lasting protection against mould Soaks up condensation Stops Mould Eliminates odours
$5.71
Provides long lasting protection against mould. Soaks up condensation. Stops Mould. Eliminates Odours. Works by a natural process automatically absorbing moisture and humidity but never over- drys the air Suitable to use in any brand refillable unit. Resealable bag provides up to 10 refills.
$18.14
Provides long-lasting protection against mould. Soaks up condensation. Stops Mould. Eliminates Odours. Works by a natural process automatically absorbing moisture and humidity but never over- drys the air
$11.41
You have seen 48 out of 56 products
Products with fungicidal protection for high-humidity or organic-residue environments. Great for wet rooms, backsplashes and maintenance areas. Confirm substrate compatibility and ventilation guidance. Use filters to refine by chemistry and service temperature. Always review the product page and TDS/SDS.
