Parfix Fast Grip is a solvent-based, brush-on contact adhesive made for kitchen and bathroom jobs where heat and moisture are a concern, supplied here in a 1L pack. It grips firmly as soon as the two coated surfaces meet, so it suits laminates, veneers, trims and similar sheet work where you want a strong bond without long clamping.About the formulaFast Grip is a polychloroprene rubber contact adhesive in a tan-coloured liquid. The solvent carrier makes the product resistant to heat, water and many solvents once cured. It does not dry clear, so keep it off visible faces and wipe back any squeeze-out or drips before they dry. The product is applied with a brush and is classed by the manufacturer as a flammable liquid (see Safety below).Where to use itIndoors: kitchen and bathroom work such as laminate and veneer fixing, trims and panels, plus general repairs where a heat and moisture resistant bond is needed.Outdoors: the supplied product information does not confirm exterior use, so check the pack or contact the manufacturer before using it on exposed work.The manufacturer's safety data lists wood, hardboard, cork, rubber, leather, canvas, laminated plastics and metals as materials it is made to bond. Test a small hidden area first, especially on foam, vinyl or other plastics, because solvents can soften or mark some of them.How to use itMake sure all surfaces are clean, dry and free of dust, oil and grease. Stir or shake the contents if needed. Brush a thin, even coat onto both surfaces and let the solvent flash off until the film is ready for bonding, following the directions on the pack. Align the pieces carefully before they touch, because a contact bond grips on first contact and there is little chance to reposition. Press the surfaces together firmly, working across the whole area. A roller or hand pressure over the full surface helps. Reseal the tin tightly after use.Important notesParfix Fast Grip is not a clear-drying glue. Do not apply it near naked flames, heaters or other ignition sources, and work only in a well-ventilated area. Always check the label for open time, cure time and clean-up directions, as these are not confirmed in our supplied data. For best results, store the tin sealed and away from heat.Specifications Brand Parfix Product Fast Grip Contact Adhesive Size 1L Colour Tan Base Solvent-based polychloroprene rubber Application Brush Dries clear No Resistance Heat, water and solvent resistant Bond Immediate grip on contact SafetyKeep away from heat, sparks and flames. Vapours may cause drowsiness or dizziness, and inhaling them can depress the central nervous system. Use only in a well-ventilated area or outdoors. Wear nitrile gloves, eye protection and suitable protective clothing. Refer to the Safety Data Sheet (SDS) for full details.
$31.89
Selleys Kwik Grip Horizontal is a flexible, solvent-based contact adhesive that grips the moment two coated surfaces meet, supplied here in a 500ml can for larger bonding jobs. It suits both porous and non-porous materials and has a thicker body that is easy to spread on flat work, making it a handy choice for laminates, rubber, leather, cork and timber around the home, workshop or job site.About the formulaThis is a polychloroprene contact adhesive in a solvent carrier, light amber in colour. The thicker consistency helps it spread without running or stringing, and it is designed for bonding without clamping once the surfaces are joined. The cured bond is flexible, heat resistant up to 130°C, water resistant and holds up against dilute acids and alkalis.Where to use itIndoors: fixing laminate sheet to benchtops and cabinetry, bonding cork, felt and rubber, repairing leather and canvas items, and general workshop or furniture jobs.Outdoors: repairing tents, car covers and other outdoor canvas equipment, and refitting rubber seals, as the cured bond is rated for exterior use.Suitable materials include laminated plastics (such as Laminex and Formica), rubber, leather, canvas, felt, timber, hardboard and compressed board, cork, metals including aluminium, and fibre cement sheeting. Test any other plastic on an offcut first.How to use it Make sure both surfaces are clean, dry and free of dust, grease and loose material. Apply an even coat to both surfaces using a brush or spreader. Leave the surfaces apart until the adhesive is touch dry. This takes about 20 minutes and should not exceed 40 minutes. Line the surfaces up carefully before they meet, using spacers such as dowels on large panels, because the bond grabs immediately on contact. Press the surfaces together firmly, working from one edge, then roll or press with a padded block to bring the whole area into contact. For small porous areas, you can apply to one surface only, join while wet and clamp until dry. Wipe away wet excess with mineral turpentine. Important notesFull bond strength develops in about 24 hours. Do not use on polyethylene or polypropylene. Some plastics, including vinyl sheeting and polystyrene, can be attacked by solvent-based contact adhesives, so test first. Warped or curved surfaces may need clamping. Use only in a well-ventilated area and keep away from heat, sparks and open flames.Specifications Brand Selleys Product Kwik Grip Horizontal Contact Adhesive Pack 500ml can Colour Light amber Base Solvent-based polychloroprene Application Brush or spreader, applied to both surfaces Open time Touch dry in about 20 minutes (maximum 40 minutes) Full strength About 24 hours Heat resistance Up to 130°C Use Interior and exterior SafetyWear protective gloves, protective clothing and eye protection, and use a suitable respirator if there is an inhalation risk. Use outdoors or in a well-ventilated area, keep away from ignition sources and do not smoke. Keep the container tightly closed and store it in a cool, well-ventilated place away from heat. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$28.34
Selleys Kwik Grip Gel Vertical Contact Adhesive is a thick, non-drip contact adhesive made for bonding upright and overhead surfaces, supplied here in a 400g can. The gel body stays put where a runny contact cement would sag, so it suits wall-mounted laminates, panels and other large flat pieces that need to grip the moment they meet.About the formulaA solvent-based polychloroprene contact adhesive in a light amber gel. It works on both absorbent and non-absorbent surfaces. The gel consistency spreads easily with a brush and resists running and stringing. You coat both surfaces, let them become touch-dry, then press them together and the bond grips straight away. Once cured, the bond is water resistant and handles heat up to 130°C. Selleys also notes that the cured adhesive resists dilute acids and alkalis.Where to use itIndoors: laminate and veneer onto vertical panels and cabinetry, cork and felt onto walls or boards, rubber and leather trims, canvas and upholstery-type repairs.Outdoors: weather-exposed fixings on suitable substrates, where a heat and water resistant contact bond is needed.Suitable materials include cork, rubber, felt, canvas, leather, metals, timber, laminated plastics (such as Laminex and Formica), hardboard and compressed board. Do not use it on polyethylene or polypropylene plastics.How to use itMake sure both surfaces are clean and dry before you start. Work in temperatures between 10°C and 35°C. Brush an even coat onto both surfaces, then wait until the adhesive is almost dry to the touch. Press the surfaces together firmly and accurately, because contact adhesives grip on contact and cannot be repositioned afterwards. No clamping is needed. Reseal the can tightly after use.Important notesThe bond grips immediately but reaches full strength after about 24 hours. Do not apply below 10°C. This adhesive is not suitable for polyethylene or polypropylene. Test a small hidden area first on any sensitive or unusual material, such as foam or soft plastics, as the solvents can affect them.Specifications Brand Selleys Product Kwik Grip Gel Vertical Contact Adhesive Pack 400g can Colour Light amber Base Solvent-based polychloroprene Form Non-drip gel Application Brush, to both surfaces Application temperature 10°C to 35°C Set Immediate grip on contact Full cure 24 hours Heat resistance Up to 130°C Use Interior and exterior Can size (approx.) 87 x 87 x 116 mm SafetyKeep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Use it in a well-ventilated area. Vapour may cause drowsiness or dizziness, and the product can irritate skin and eyes. Wear protective gloves and eye protection. Refer to the Safety Data Sheet (SDS) for full details.
$31.83
SikaBond-105 ContactFix is a premium, high strength contact adhesive from Sika, supplied here in a 500mL can for laminate fabrication, upholstery and general sheet bonding. It is a one-component adhesive that dries quickly and gives a strong bond that stands up to heat and moisture, which makes it a practical pick for workshop and trade jobs.About the formulaA one-component polychloroprene (synthetic rubber) contact adhesive. It has a short flash-off time, high initial strength and good resistance to ageing, with a broad adhesion range across common sheet and covering materials. The manufacturer lists a tack-free time of roughly 5 to 8 minutes and heat resistance up to 90°C.Where to use itIndoors: fixing plastic laminates to timber, MDF or particleboard, and covering furniture and joinery with fabric, vinyl or foam.Vehicles and upholstery: Sika lists room-temperature contact bonding of covering materials such as PUR foams and textiles, plus steps, wheel arches, seat brackets and side walls. It also suits cover trims and edging profiles that spring back strongly, and auto and furniture upholstery.Suitable materials include timber, rubber sheets, plastic laminates, fabric, cloth-backed and polyester-backed vinyl, MDF, particleboard, concrete, glass and metal sheets. Test on your actual materials and conditions first to confirm adhesion and compatibility.How to use it Make sure both surfaces are sound, clean, dry and free of dirt, oil, grease, loose coatings and friable material. Apply an even coat to both surfaces. Earlier Sika data sheets list a roller coater, tooth comb, brush or spray gun as suitable methods. Let the adhesive dry until it is tack free (about 5 to 8 minutes, depending on conditions), then bring the surfaces together firmly with strong, even pressure. Take care with positioning, because contact adhesives bond on first contact. Clean tools and equipment while the adhesive is still uncured, using Sika Remover-208, Sika Colma Cleaner or another suitable solvent. Important notesDo not use in temperatures below +10°C or in condensing conditions. For best results, apply at ambient, material and adhesive temperatures within the range stated on the Sika data sheet. Store unopened in the original packaging, dry and out of direct sunlight, between +5°C and +25°C. Shelf life is 12 months from the date of production. Always test compatibility on the real substrates before committing to a full job.Specifications Brand Sika Product SikaBond-105 ContactFix High Strength Premium Contact Adhesive Pack 500mL can Colour Light amber (per current Sika data sheet) Base One-component polychloroprene Density 0.81 kg/L Solids content About 17% by mass Viscosity 350 mPa.s Tack-free time About 5 to 8 minutes Consumption 6 to 8 m² per litre Temperature resistance Up to 90°C Shelf life 12 months from production Clean up Sika Remover-208, Sika Colma Cleaner or other suitable solvent SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Use only outdoors or in a well-ventilated area, avoid breathing vapours, and wear protective gloves, protective clothing and eye or face protection. If it gets on skin, remove contaminated clothing and rinse with water. For fires use alcohol-resistant foam, carbon dioxide or dry chemical, not water. Refer to the Safety Data Sheet (SDS) for full details.
$28.77
Bondall Betta Tilecare Wet Area Waterproofer is a fast-curing, water-based liquid rubber membrane for sealing wet areas beneath tiles and renders, supplied here in a 10L pail for bigger bathroom, laundry and balcony jobs. It dries to a flexible, elastic film that acts as a water and vapour barrier, and it is designed to cope with permanently wet conditions, including ponding water once cured.About the formulaA water-based, one-part elastomeric membrane that is described by the manufacturer as non-toxic and non-flammable. It is classed as a Class III membrane under AS/NZS 4858 and, when used with the Betta detailing range, is designed to meet the Australian wet area requirements including AS 3740. The fast-curing formulation lets you tile or render over it quickly, and it is compatible with a range of tile adhesives, renders and toppings. No primer is needed on plasterboard or sound, dry concrete.Where to use itIndoors: bathroom and laundry floors and walls, shower recesses and other tiled wet areas, plus under screeds and toppings.Outdoors: balconies, decks, podiums and terrace floors, planters and retaining walls, and roofs that will be covered with screeds or toppings.Suitable substrates include concrete, screeds, renders, brick, plasterboard, fibre cement sheet and marine plywood. It sits under ceramic, porcelain, granite, marble and other stone tile finishes. Other surfaces, such as smooth, dense or damp ones, may need a Betta primer first, so check the technical data sheet for your substrate.How to use itMake sure the surface is sound, stable, clean and free of dust, oil, grease and loose material. Install the bond breaker and elastic joint band detailing first, as this is part of meeting AS 3740. Apply by brush, roller or spray unit in a minimum of two coats, changing direction between coats, to a total minimum coverage of 1.5 litres per square metre. This builds a dried film of roughly 1.2mm. Vertical or pitched areas can be done at around 1 litre per square metre. Take the membrane up walls at least 150mm in general wet areas and to 1.8m in shower recesses, finishing with a continuous, seamless film. Clean tools with water straight after use.Important notesTypical drying times at normal conditions (about 20°C, 50% humidity): tack free in about 45 minutes, recoat in about 1 hour, and ready to tile or topping over in about 4 hours. Retailer information quotes 6 hours before tiling, so allow the longer time in cool or humid weather and always follow the pack. Allow ample cure time before flood testing, as Bondall publishes more than one figure for this. Finish toppings must be water-based and solvent-free. Areas with rising damp or negative pressure should first be treated with Betta Damp Stop. Use on concrete slabs with hydrostatic or vapour pressure from below is outside the scope of the independent appraisal. Do not apply when rain is imminent. Always check the technical data sheet for your project.Specifications Brand Bondall (Betta Tilecare) Product Wet Area Waterproofer Pack 10L pail Base Water-based liquid rubber (elastomeric) Application Brush, roller or spray unit Coverage Minimum 1.5L per m2 over two coats (about 6.6 m2 per 10L pail) Dried film thickness Approx. 1.2mm Tack free About 45 minutes Recoat About 1 hour Tile or topping over About 4 to 6 hours (see notes) Standard AS/NZS 4858 Class III membrane Clean up Water Use Residential and commercial wet areas, interior and covered exterior SafetyEven so, wear gloves and eye protection, ensure good ventilation, and avoid contact with skin and eyes. Keep out of reach of children. Store in a sealed container in a cool place and protect from frost. Refer to the Safety Data Sheet (SDS) for full details.
$212.26
Mandala Art Mosaic Grout Sealer & Waterproof Additive is a 1L acrylic-based liquid made for mosaic artists and hobbyists who want to strengthen, seal and waterproof their grout with a single product. It can be mixed into grout powder or brushed over finished work, which makes it handy for outdoor pieces such as birdbaths and pavers.About the formulaAn acrylic-based white liquid that adds strength and flexibility to grout. Used correctly, it gives the grout water resistance, helps reduce mould growth and deepens the grout colour. It leaves a slight sheen on the finished surface.Where to use itIndoors: mosaic artworks, craft projects and decorative pieces where you want stronger, sealed grout lines.Outdoors: birdbaths, outdoor pavers and garden mosaics that will be exposed to moisture.It can also be used as a surface sealer on wood and MDF, and on porous surfaces such as terracotta and ceramic.How to use itFor a waterproof grout, use the additive in place of the water when you mix your grout powder, then stir to a smooth, toothpaste-like consistency and apply as normal. For extra strength and durability, you can brush a final coat of the additive over the project once the grout has dried. As a surface sealer, brush it onto the clean, dry surface. Check the product label for mixing and drying details, as the correct method matters for good results.Important notesThe manufacturer does not recommend this product for large works such as swimming pools. Water resistance and waterproofing depend on correct use. Use as directed on the label, and do a small test on a spare piece first if you are unsure about a surface. Specific mixing ratios, drying times and coverage have not been confirmed here, so please follow the pack instructions.Specifications Brand Mandala Art Product Mosaic Grout Sealer & Waterproof Additive Model GSA Size 1L bottle Colour White liquid Base Acrylic Application Mixed into grout powder in place of water, or brushed on as a sealer Finish Slight sheen, enhances grout colour Use Indoor and outdoor mosaics SafetyAvoid contact with eyes and prolonged skin contact, use in a well-ventilated area, and wash hands and tools after use. If it gets in the eyes, rinse with plenty of water. Keep out of reach of children and store the container sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$30.29
![Fastfix Wet Shield One Coat Instant Waterproofing 2.5kg [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/fastfix-wet-shield-one-coat-instant-waterproofing-2-5kg-grey-2.jpg?v=1792410637&width=645)
Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$89.91
Crommelin One Coat Rapid is a heavy-duty, liquid-applied waterproofing membrane that goes down before tiling, supplied here in a 1L pail for showers, laundries and other small wet-area jobs. It is a polyurethane-modified grey membrane that cures into a seamless, flexible layer under tile, so there are no laps or joins in the finished surface.About the formulaThe membrane is polyurethane modified for high flexibility and reinforced for strength and durability. Crommelin states it stretches by more than 300% and stays flexible over time, which helps it cope with minor substrate movement. It dries to a keyed, slightly textured surface that gives cement-based tile adhesive something to grip. It is made to be used with cement-based tile adhesives that comply with AS 2358, and it is designed to meet AS 4858 and AS 3740. It is water based, so tools clean up with water.Where to use itIndoors: showers, bathrooms, laundries and kitchens, on both walls and floors, before tiling.Outdoors: balconies, patios and podiums under tile, where the membrane is covered by the tile finish.Suitable substrates include concrete, cement render and screeds, plasterboard and wet-area plasterboard, suitably prepared compressed fibre cement sheet, timber, plywood, wet-area particleboard and steel.How to use itSurfaces need to be sound, clean and dry, with loose or crumbling material removed first. New concrete should have cured for at least 28 days before coating. Where the manufacturer's data sheet calls for a surface primer, use a 1:1 dilution of the membrane with water and let it dry. On walls, one coat is enough, and Crommelin quotes coverage of up to 2m² per litre. Floors need more material per square metre, and complex or irregular surfaces may need extra coats, so check the technical data sheet for your job. Allow good airflow while it cures. Once the membrane has cured, a flood test is described in the manufacturer's data sheet: water about 25mm deep for 2 hours, removed straight afterwards. Clean tools with water before the membrane dries. Uncured material can be removed with warm water and detergent.Important notesThis membrane is not designed to go directly onto white-set plaster. Prime that surface first with a coat of Crommelin Next Day New Concrete Sealer and let it dry. Full cure takes about 7 days. Re-coat and cure times get longer in cold, humid or still conditions. Tile over the membrane so it is not left exposed. Waterproofing wet areas is regulated work in many parts of Australia, so check local requirements and follow the manufacturer's full instructions.Specifications Brand Crommelin Product One Coat Rapid Under-tile Waterproofing Membrane Pack 1L pail Colour Grey Base Polyurethane-modified, liquid applied, water clean up Elongation Over 300% Coverage Up to 2m² per litre (see data sheet for floors and irregular surfaces) Full cure About 7 days Standards Designed to comply with AS 4858 and AS 3740 Use Interior and exterior under-tile applications SafetyUse it with good general ventilation, avoid prolonged skin and eye contact, and wash your hands after use. Store the pail sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$36.48
Crommelin Exterior Grade Brushable Waterproofing Membrane is a tough, flexible synthetic rubber coating for external areas that stay wet, supplied here in a 15L pail for larger jobs. It is designed for permanent water contact, for non-exposed areas with pedestrian traffic, and for use beneath screeds and toppings. It is built to move with the structure rather than crack as the building shifts.About the formulaA ready-to-use, water-based, synthetic rubber membrane (styrene butadiene rubber) in grey. It stays permanently flexible, bridges existing cracks up to 1.5mm and bonds to a wide range of building substrates. It is low VOC and dries quickly. Once cured it can be overcoated with screeds, renders and water-based coatings, so it suits layered waterproofing systems.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin offers separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits other areas of permanent water contact and non-exposed areas under screeds and toppings.Suitable substrates listed by the manufacturer include concrete and brick, cement render, plywood sheeting, cement sheeting, lightweight aggregate block, trafficable screeds, aluminium and steel (suitably primed).How to use itSurfaces must be sound, clean and completely dry, with no dust, grease, curing compounds, release agents, loose particles or efflorescence. Test moisture content before coating, ideally with an electronic moisture meter. Concrete should be cured for at least 28 days, and screeds and renders for at least 7 days. Remove high points and fill blow-holes and honeycombing with a suitable repair mortar. If the substrate is damp, prime it with Crommelin Dampstop. Treat any rust and remove loose rust material before coating metal. Stir the membrane well, then apply with a Crommelin applicator brush or roller at a surface and air temperature between 10 and 35 degrees Celsius. Recoat once touch dry, which is about 2 hours. Apply the second coat at right angles to the first. Reinforce corners, gutter damage and pin holes with Crommelin reinforcing fabric or bandage. Fit a suitable protection board over the cured membrane before any backfilling.Important notesDo not apply in extreme temperature or humidity. Full cure is about 7 days at 25 degrees Celsius, and coverage varies with substrate porosity. This product is intended for non-exposed pedestrian traffic, so protect the membrane from mechanical damage. Crack bridging applies to existing cracks up to 1.5mm only. Check the current manufacturer data sheet for your specific application and overcoating requirements.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofing Membrane Pack 15L pail Colour Grey Base Water-based synthetic rubber (styrene butadiene rubber) Application Brush or roller Coverage About 1.5m² per litre, roughly 11m² of finished coating per 15L Recoat time About 2 hours Full cure About 7 days at 25°C Crack bridging Existing cracks to 1.5mm Application temperature 10°C to 35°C Use Exterior, permanent water contact, non-exposed trafficable areas, under screeds and toppings SafetyAvoid contact with skin and eyes, wear suitable gloves and eye protection, and ensure good ventilation when applying. Store in a cool, dry place with the lid sealed. Wash tools in water before the membrane cures. Refer to the Safety Data Sheet (SDS) for full details.
$336.74
Crommelin Shower Sealer & Waterproofer is a clear, water-based silicate treatment designed to stop leaking showers by waterproofing the grout from within, with no need to rip out tiles. It soaks deep into cementitious grout and reacts inside it to block the passage of moisture, making it a practical fix for old, porous grout in showers, bathrooms and balconies. This listing is for a single 500ml bottle.About the formulaA waterborne silicate treatment that penetrates grout to a depth of up to 20mm. Once in the grout it undergoes a chemical reaction that Crommelin says permanently blocks moisture, and it dries completely clear so your tiles and grout lines look the same afterwards. It is a ready-to-use, single coat treatment, so there is no mixing, and equipment cleans up with water.Where to use itIndoors: shower recesses, bathrooms, kitchens and laundries with cementitious grout that has started to leak or let moisture through.Outdoors: balconies and other external areas with cementitious grout or similar cementitious construction materials.Suitable substrates are cementitious grout and other cementitious construction materials. It is not suitable for epoxy grout.How to use itPreparation: make sure the area is cementitious and free of dirt, mould, mildew and other contaminants. Wash with a strong bleach solution and rinse well. Replace any loose or drummy tiles and repair damaged or cracked grout with cementitious grout. Seal metal inserts with silicone, and make sure wall-to-wall and wall-to-floor joints are sealed with silicone rather than grout. The surface must be dry, so leave the area to dry for at least 12 hours before applying.Application: shake the bottle well, then apply liberally to the grout joints only, using a thin brush or a Crommelin Sealer Applicator Wheel. Wipe any excess off the tile surface with a damp cloth before it dries. Leave to dry for 30 to 40 minutes, then water the area thoroughly and scrub off any remaining excess. The area can be used straight away.Conditions: apply only when surface and air temperatures are within 10°C to 35°C, and avoid application when humidity is high or likely to be during the initial cure (maximum recommended humidity is 85%).Clean up: wash brushes and tools with water before the product dries.Important notesFull cure takes 7 days. Not suitable for epoxy grout. The grout must be clean and dry, and contaminants such as mould or old sealers can stop the treatment from penetrating properly. Crommelin's data sheet gives coverage of roughly 200 to 300 lineal metres of 5mm grout from the 500ml bottle, so actual coverage depends on grout width, depth and porosity. For full preparation and application detail, follow the Crommelin instructions and technical data sheet.Specifications Brand Crommelin Product Shower Sealer & Waterproofer Pack 1 x 500ml bottle Manufacturer code 6001-500 Colour Clear (dries clear) Base Waterborne silicate treatment Application Thin brush or Crommelin Sealer Applicator Wheel, grout joints only Penetration Up to 20mm into grout Dry time before watering in 30 to 40 minutes Full cure 7 days Application temperature 10°C to 35°C Coverage Approx. 200 to 300 lineal metres of 5mm grout (per manufacturer TDS) Clean up Water, before the product dries Use Interior and exterior SafetyAs a general precaution, avoid contact with eyes and skin, keep out of reach of children, and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$61.24
Crommelin Blackseal Heavy Duty is a water-based, rubber-modified bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 1L size that suits planter boxes, pots, timber posts and small retaining wall jobs. It is made for surfaces that stay damp or wet and will not be painted, tiled or covered with a finishing coat.About the formulaCrommelin describes Blackseal as a commercial grade bitumen emulsion modified with a synthetic rubber co-polymer. The rubber modification keeps the cured film flexible, so it stays watertight under permanently wet conditions and is suitable for permanent immersion. It helps prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. It grips a wide range of substrates, is fast drying, and the maker lists it as non-toxic and non-flammable. It can be thinned with up to 50% water to make a bitumen paint.Where to use itIndoors: not intended for interior finishing work or any area that needs a paintable or tileable surface.Outdoors: below-ground and non-exposed exterior surfaces such as garden retaining walls, planter boxes, plant pots, timber posts, water tanks and other non-critical moisture barrier jobs.Suitable materials include concrete, masonry, cement sheeting, timber and metal (check the label for the full substrate list and do a small test area first).How to use itStart with a clean, sound surface free of dust, grease, loose material and anything that could stop the membrane bonding. Stir the product well and apply it evenly with a brush or roller, then allow it to dry before any further coats. Check the label and Crommelin's full instructions for coverage, coat numbers and drying times before you start, and protect the cured membrane from damage if you will be backfilling against it. Clean tools before the product dries (as a water-based product, warm water is the usual method, but confirm on the pack).Important notesNot suitable where it will be exposed to UV or sunlight. It cannot be painted, tiled over, rendered or over-coated, and it is not for trafficable surfaces. If you need a UV-stable option, look at a different Crommelin product. Coverage and cure times depend on the surface and conditions, so treat the listed coverage as a guide and test a small area first.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Size 1L Colour Black Base Water-based bitumen emulsion, modified with a synthetic rubber co-polymer Application Brush or roller Coverage Approx. 0.75 m² per 1L (retailer listed, guide only) Dilution Up to 50% water to make a bitumen paint Use Below-ground and non-UV-exposed exterior areas Not suitable for UV exposure, painting, tiling, over-coating, trafficable surfaces SafetyThe product itself is not combustible, but once the water has evaporated the organic components can burn or break down in a fire. Avoid contact with eyes and skin, keep out of reach of children, and wash off spills and splashes promptly. Refer to the Safety Data Sheet (SDS) for full details.
$20.75
Crommelin Blackseal Heavy Duty is a black, water-based bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 15L pail for larger jobs. It is a bitumen emulsion modified with a synthetic rubber co-polymer. It dries to a strong, flexible film that stays watertight in permanently wet conditions, which makes it a practical, economical choice where the finished membrane will stay out of sight and out of the sun.About the formulaA water-based bitumen emulsion with a synthetic rubber co-polymer for added flexibility and strength. It grips well to a wide range of building surfaces and is designed to help prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. The manufacturer describes it as non-toxic, non-flammable, fast drying and suitable for permanent immersion. It can be thinned with up to 50% water if you want a bitumen paint instead of a full-strength membrane.Where to use itIndoors: not intended for interior wet areas such as showers or bathrooms, because it cannot be tiled over or finished with a top coat.Outdoors: below-ground and non-exposed outdoor surfaces, including garden retaining walls, planter boxes, plant pots, timber posts and water tanks. It suits non-critical waterproofing jobs, not areas next to habitable spaces.Suitable surfaces include concrete, concrete blocks, brickwork and other masonry, renders, cementitious substrates, compressed cement and fibre cement sheeting, natural stone, plywood sheeting and timber. It also works on aluminium and steel that have been suitably prepared.How to use itStart with a clean, sound surface free of dust, grease, loose material and flaking coatings. Stir the pail well, then apply with a brush or roller. Two coats are recommended, and the 15L pail covers about 11.25 square metres at that rate. Let each coat dry before applying the next. Mix with water only if you want to thin it for use as a bitumen paint, and do not go past 50% dilution. Wash tools with water straight after use, before the product dries. Check the current Crommelin product information sheet for recoat times and full preparation advice before you start.Important notesDo not paint, tile over or over-coat this membrane, and do not use it on trafficable surfaces. It is not suitable where UV stability is required, so keep it covered or buried. For shower areas or UV-exposed roofs and walls, choose a purpose-made Crommelin membrane instead. Because it is for non-critical applications only, it is not a substitute for a compliant waterproofing system in habitable or wet areas. Cure times vary with temperature, humidity and airflow, so allow enough time before backfilling or exposing the membrane to heavy moisture.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Pack 15L pail Colour Black Base Water-based bitumen emulsion modified with synthetic rubber co-polymer Application Brush or roller Number of coats 2 Coverage About 11.25 square metres per 15L (two coats) Dilution Up to 50% water to make a bitumen paint Clean up Water, while wet Use Below ground and non-UV-exposed areas only SafetyUse it with good general ventilation. Normal site protection such as safety glasses and overalls is sensible, along with good hygiene. Store the pail sealed, away from extreme temperatures and freezing, and keep it away from strong oxidising agents, strong acids and strong bases. Do not let large spills reach drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$125.78
Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$37.54
Crommelin Shower Waterproofing Membrane is a ready-to-use, water-based liquid membrane for waterproofing wet areas before tiling, supplied here in a 15L pail for larger bathroom, laundry and balcony jobs. It cures to a continuous, flexible rubber-like layer with a textured surface, so cement-based tile adhesive can bond directly over the top.About the formulaA heavy duty, modified rubber (styrene butadiene rubber) liquid membrane that is applied seamlessly, with no joins or laps, for leak-free performance. It stays permanently flexible with high elongation, so it can cope with normal movement in the substrate. It dries to a keyed finish suited to all cement-based tile adhesives that conform to AS 2358, and it complies with AS 3740 (Waterproofing of wet areas). It is a water-based product, so tools clean up with water.Where to use itIndoors: under tiles in showers, bathrooms, laundries, kitchens and wet rooms, on both walls and floors.Outdoors: under-tile waterproofing on balconies. The membrane can be applied either below or above a screed.Suitable substrates include concrete and masonry, cement renders and screeds, plasterboard and wet area gyprock, compressed fibre cement sheeting, timber, plywood sheeting and wet area particleboard, and suitably prepared steel.How to use itPrepare the surface first. Remove high points and protrusions, fill any blow-holes or honeycombing with a suitable repair mortar, and bring the surface back to an even profile. New concrete should have cured for at least 28 days and screeds or renders for at least 7 days. The surface must be clean, sound and completely dry. Free it from dust, grease, curing compounds, release agents and loose particles. Check moisture with a meter. If the substrate is not dry enough, prime it with Crommelin Dampstop.The membrane is ready to use, so stir it well and apply with a brush or roller. Apply at least two coats and allow the first to dry before recoating. Complex or very irregular surfaces may need extra coats. Apply only when surface and air temperatures are between 10 and 35 degrees C and humidity is below 85%.Tile over after the membrane has dried and cured for the recommended time. A flood test can be done after 48 hours by ponding water to a depth of 25mm for 2 hours, then removing the water straight away. Wash tools with water before the product dries. Uncured material can be removed with warm water and detergent.Important notesNot suitable for use over white-set plaster. Do not apply over damp substrates, and do not apply in extreme heat, cold or humidity. Allow good airflow so the membrane can cure properly. Full cure takes about 7 days. Recoat and tile-over times vary with temperature and humidity, so check the current Crommelin data sheet for your conditions. Crommelin lists companion products for detailing, including reinforcing fabric with bond breaker, Dampstop primer, polyurethane sealant and Silicone WP Plus. Always apply a trial patch if you are unsure about a substrate.Specifications Brand Crommelin Product Shower Waterproofing Membrane Pack 15L pail Colour Green Base Water-based, modified rubber (SBR) liquid applied membrane Application Brush or roller, ready to use after stirring Coverage About 2m2 per litre per coat, minimum 2 coats (about 15m2 of finished membrane from 15L) Application temperature 10 to 35 degrees C, maximum humidity 85% Tile over After a minimum of 48 hours Full cure 7 days Standards Complies with AS 3740; suitable for use with cement-based tile adhesives conforming to AS 2358 Use Under-tile wet area waterproofing SafetyEven so, ensure good ventilation, avoid breathing vapours or spray, avoid skin and eye contact, and wear gloves and eye protection. Remove splashes from skin promptly. Keep the container sealed when not in use, store it cool and dry, and protect it from freezing and extreme temperatures. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$273.47
Crommelin Shower Waterproofing Membrane is a ready-to-use, liquid-applied under-tile membrane for waterproofing showers and other wet areas before tiling, supplied here as a 1L pail for small jobs and repairs. It cures to a seamless, flexible waterproof layer with a textured surface that tile adhesive can grip, so you can tile straight over it.About the formulaA water-based, heavy-duty, modified rubber membrane that is applied wet and dries into a continuous film with no joins to leak. The manufacturer describes it as permanently flexible with high elongation, with excellent adhesion to the substrate and a keyed finish that promotes direct tile adhesion. It complies with AS 3740 (Waterproofing of domestic wet areas) and is suitable for use with cement-based tile adhesives that conform to AS 2358. It can be applied either below or above a screed.Where to use itIndoors: showers, bathrooms, laundries, kitchens and wet rooms, on both walls and floors, under tiles.Outdoors: balconies, under tile.Suitable substrates include concrete and masonry, cement renders and screeds, plasterboard and wet area plasterboard, compressed fibre cement sheet (suitably prepared), timber, plywood sheeting, wet area particleboard and steel. It is not suitable for use over white-set plaster.How to use it Prepare the surface so it is clean, dry, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Concrete should have cured for at least 28 days, and screeds and renders for 7 days. Fill any holes or honeycombing with a suitable repair mortar and remove high points so the surface is even, with a light texture. If the substrate is not dry, prime it with Crommelin Dampstop. If the surface needs more consolidation, apply one coat of Crommelin Powerflex first. The product is ready to use. Stir it well, then apply with a 75mm or 100mm membrane brush or a 230mm membrane roller cover. Apply only when surface and air temperatures are between 10°C and 35°C. The manufacturer's recoat time is about 2 hours and the tile-over time is about 48 hours. Follow the Crommelin technical data sheet for detailing at corners, joints and penetrations. Important notesOne litre produces about 1m² of finished membrane, which means building up the full film in the coats the technical data sheet specifies. Do not apply in conditions that are too hot or too cold. Make sure the substrate is properly cured and prepared before you start, because the membrane is only as good as the surface under it. For anything beyond a small area or minor repair, the 4L size may suit better. Check the current Crommelin data sheet for the full system and for the requirements that apply to your job.Specifications Brand Crommelin Product Shower Waterproofing Membrane Pack 1L pail Colour Green Base Water-based, modified rubber, liquid applied Application Brush or roller Coverage About 1m² of finished membrane per litre Recoat time About 2 hours Tile over About 48 hours Application temperature 10°C to 35°C Standards Complies with AS 3740; compatible with cement-based tile adhesives to AS 2358 Use Interior and exterior, under tile SafetyUse it with good general ventilation, avoid contact with skin and eyes, and wear suitable protective clothing. Do not let large spills reach drains or waterways. Store the pail in a cool, dry place out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$34.14
Crommelin Shower Waterproofing Membrane is a ready-to-use, water-based liquid membrane that waterproofs showers, bathrooms and other wet areas before tiling, supplied here in a 4L pail. It rolls or brushes on as a seamless, flexible layer and dries to a textured finish that tile adhesive can grip, so you can tile directly over it.About the formulaA heavy duty, modified rubber membrane in a water-based, ready-to-use form with no mixing. Once cured it stays permanently flexible and stretches well, so it can cope with small movements in the substrate. It sticks well to suitable surfaces. The keyed surface works with cement-based tile adhesives, and Crommelin states it suits all cement-based adhesives that meet AS 2358. It complies with AS 3740 (waterproofing of wet areas). The 4L pail makes about 4 square metres of finished membrane, which is enough for a standard single shower recess.Where to use itIndoors: under-tile waterproofing of shower recesses and bathrooms, on both walls and floors, and in other internal wet areas such as laundries.Outdoors: not specified by the manufacturer for this product. Check the Crommelin technical data sheet or contact Crommelin before using it on exposed external areas.Suitable surfaces listed by the manufacturer include concrete and masonry. Check the current technical data sheet for the full list of approved substrates, and confirm that wet area fibre cement, plasterboard or similar sheeting is approved before you start.How to use it Make sure the substrate is clean, sound and completely dry before you apply anything. Apply with a brush or a suitable membrane roller. Crommelin lists its Contractor Membrane Roller Cover as a compatible tool. At least 2 coats are required. Apply the second coat at 90 degrees to the first. Allow about 2 hours drying time between coats, as per the Crommelin how-to guide. Coverage is about 2 square metres per litre per coat. Complex or very irregular surfaces may need extra coats. Crommelin lists Dampstop, Reinforcing Fabric (with or without bond breaker), Polyurethane Sealant and Silicone WP Plus as compatible products for details and junctions. For a flood test, wait 48 hours, then pond water to a depth of 25mm for 2 hours. Remove the test water straight away afterwards. You can tile over the membrane after 48 hours. Clean tools and equipment with water before the membrane dries. Important notesFull cure takes 7 days. Do not apply to a damp substrate. Wet area waterproofing should be done to the requirements of AS 3740 and your local regulations, and many jurisdictions require a licensed waterproofer for the work. If in doubt, check before you start. This product is water-based, so keep the pail sealed and protect it from frost and extreme heat during storage.Specifications Brand Crommelin Product Shower Waterproofing Membrane Size 4L pail Colour Green Base Water-based, modified rubber Application Brush or roller, 2 coats minimum Coverage About 2 m² per litre per coat (about 4 m² finished membrane from 4L) Recoat About 2 hours Tile over / flood test After 48 hours Full cure 7 days Standards Complies with AS 3740; suitable with cement-based tile adhesives to AS 2358 Use Under-tile waterproofing of showers, bathrooms and wet areas, walls and floors Clean up Water, before drying SafetyAvoid contact with eyes and skin, and wear gloves and eye protection when applying it. Make sure the area is well ventilated while you work and while it dries. Keep out of reach of children. If it gets in your eyes, rinse with plenty of water. Refer to the Safety Data Sheet (SDS) for full details.
$93.15
![Crommelin Exterior Grade Brushable Waterproofer 1L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/crommelin-exterior-grade-brushable-waterproofer-1l-grey-2.jpg?v=1792410528&width=645)
Crommelin Exterior Grade Brushable Waterproofer is a grey, synthetic rubber based liquid membrane for areas that stay wet, including permanent immersion, protected pedestrian areas and surfaces that will be covered by a screed or topping. This 1L pail suits small repairs and compact jobs. It dries to a tough, flexible film that moves with the structure underneath.About the formulaA water based, ready-to-use membrane built on synthetic rubber (styrene butadiene rubber). The manufacturer describes it as low VOC and fast drying, with good adhesion to a wide range of building surfaces. It stays flexible after curing so it can follow structural movement, and it can bridge existing cracks up to 1.5mm. It is suitable for permanent water immersion and, per the manufacturer's technical data sheet, for collecting and storing potable water. Once cured it can be overcoated with screeds, renders and water based coatings.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin makes separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits non-exposed pedestrian areas and applications under screeds and toppings.Suitable surfaces listed by the manufacturer include concrete, brickwork, concrete blocks, cement render, screeds, fibre cement sheeting, plywood sheeting and steel (suitably prepared or primed). The technical data sheet also lists aluminium and lightweight aggregate block.How to use itSurfaces must be clean, dry and sound, and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Concrete should have cured for at least 28 days, and screeds and renders for at least 7 days. The manufacturer calls for a moisture test to confirm the substrate is dry enough to coat, and recommends an electronic moisture meter. Remove high points, fill blow-holes and honeycombing with a suitable repair mortar, and make good any defects. Masonry should be flush pointed.The product is ready to use, so stir it well before applying. Apply with a brush or roller. Use a bond-breaking sealant in all joints, junctions, protrusions, angles and internal corners, and apply the membrane to the positive side of the substrate. Apply two coats at the recommended rate, running the second coat at right angles to the first once the first is touch dry (about 2 hours). Apply only between 10°C and 35°C and in humidity no higher than 85%. Wash tools with water before the product dries.Important notesAllow a minimum of 72 hours before backfilling and about 7 days for full cure. Ensure good airflow while curing, and do not expose the membrane to moisture until it has fully cured. Protect the membrane from damage, and install suitable protection board before any backfilling. Do not apply in extreme weather or humidity. If the substrate is not dry, the manufacturer advises priming with Crommelin Dampstop, so check the full instructions on the Crommelin website for your substrate. Avoid applying the membrane too thickly in corners, as this can reduce flexibility. This listing is for the brushable (pail) product, not the sprayable aerosol version.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofer (Exterior Grade Waterproofing) Model number 1081-001 Pack 1L pail Colour Grey Base Water based, synthetic rubber (styrene butadiene rubber) membrane Application Brush or roller, 2 coats Coverage About 1.5m² per litre per coat, so about 0.75m² of finished two-coat membrane per 1L Crack bridging Existing cracks up to 1.5mm Recoat time About 2 hours Backfill Minimum 72 hours Full cure 7 days Application conditions 10°C to 35°C, humidity up to 85% Clean up Water, before the product dries Use Exterior, permanent immersion, non-exposed pedestrian areas, under screeds and toppings SafetyIt is stable under normal storage and use, and is incompatible with strong oxidising agents, strong acids and strong bases. Avoid contact with skin and eyes, wash tools and any spills with water while the product is wet, and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$34.76
Gripset Betta Bitumen Rubber is a two-in-one, solvent-free liquid membrane in a 1 litre pail, supplied here for waterproofing underground, immersed and general building work. Apply it as a bitumen polymer membrane, or dilute it with water to make an economical black bitumen paint where a full membrane is not needed.About the formulaA water-based, concentrated bitumen and latex polymer liquid that dries to a flexible black film. The manufacturer describes it as solvent free, with good sealing and adhesion on a range of building surfaces. It can be applied to damp surfaces provided there is no standing water, and it is approved for potable water contact (tested at an exposure of 1000mm2 per litre). Diluted 1:1 with water, 1L of concentrate makes 2L of bitumen paint.Where to use itIndoors: interior areas that need a waterproof or protective coating, where a membrane or bitumen paint suits the job.Outdoors: underground and retaining walls, garden beds, planter boxes and landscaped areas, fish ponds, stock troughs and water features, and general protective coating work. It also suits fully immersed applications when applied at the higher immersed coverage rate.Suitable surfaces include concrete, masonry, brick, timber, cement sheeting, metals and aged bitumen, along with other common building surfaces. If you plan to coat over existing paints or finishes, check with Gripset Betta first.How to use itStart with a clean, sound surface free of loose material and standing water. The product is self-priming. For porous surfaces, the manufacturer's literature suggests diluting the first coat with water (about 1 part concentrate to 3 parts water). Use a separate primer on non-porous or smooth surfaces and on surfaces affected by rising damp. Apply by brush, roller, trowel or spray, working each extra coat in a different direction to the one before.As a membrane, apply at least 2 coats at a combined minimum of 1.5 litres per square metre, which gives a dried film of about 1.2mm. For immersed areas, allow a minimum of 2 litres per square metre. Uneven or porous surfaces can need more. For paint use, mix the concentrate with clean water 1:1 by volume. Wash tools in water while the product is still wet.Important notesDrying times at about 20°C: tack free in 60 to 90 minutes, recoat after 2 to 4 hours, dry film in 24 hours, backfilling underground after 4 days, and immersed areas after 21 days. Temperature, humidity and surface porosity all change these times. Once dry, the product has to be removed mechanically or with solvent. For potable water use, wash the surface down and discard the first fill before using the water for drinking. At the minimum membrane rate, 1L covers well under 1 square metre, so check quantities before you buy.Specifications Brand Gripset Betta Product Bitumen Rubber Waterproofing Membrane Pack 1 litre pail Colour Black Base Water-based bitumen and latex polymer, solvent free Application Brush, roller, trowel or spray Membrane coverage Minimum 1.5 L/m2 in 2 coats (2 L/m2 for immersed areas) Paint dilution 1 part concentrate to 1 part water Tack free 60 to 90 minutes Recoat 2 to 4 hours Dry film 24 hours Immersed areas 21 days Clean up Water, while wet Use Interior, exterior, underground and immersed SafetyIt is non-flammable as supplied, but the dried film will burn in a general fire. Wash your hands after use and before eating, drinking or smoking. Do not let it enter drains, sewers or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$27.04
Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Blast away built up grime, dirt, and weather stains across large outdoor areas with this powerful concentrate. Designed for Aussie backyards, it cuts through tough mess on concrete, pavers, brick, tiles, and timber or composite decks so outdoor spaces look fresh and inviting again. Why you will love it Heavy duty clean that tackles road film, mildew stains, leaf tannins, and greasy marks. Concentrated value so one bottle makes multiple buckets of ready to use solution. Fast results with minimal scrubbing on most surfaces. Versatile for driveways, decks, paths, patios, and outdoor walls. Hose or pressure washer friendly for quick coverage on big jobs. Ideal surfaces Concrete driveways and garage floors Pavers, brick, stone, and outdoor tiles Timber decks and composite decking Rendered walls and fencing Outdoor furniture settings made of hard materials Dilution guide Job type Mix ratio Where to use Heavy build up 1 part cleaner to 4 parts water Oil spots, mildew stains, leaf marks on concrete and pavers General cleaning 1 part cleaner to 10 parts water Routine driveway and deck washes Maintenance 1 part cleaner to 20 parts water Frequent quick cleans and large areas Coverage: A 5L concentrate can make many litres of solution and clean a large area depending on dilution, surface porosity, and soil level. How to use Sweep the area to remove loose debris. Mix to the required ratio in a bucket or pressure washer reservoir. Wet the surface, then apply generously with a garden sprayer, watering can, mop, or pressure washer. Allow 3 to 5 minutes contact time. Do not let the solution dry on the surface. Agitate stubborn spots with a stiff outdoor broom or deck brush. Rinse thoroughly with a hose or pressure washer, pushing residue to drainage. Tips for best results Test on a small hidden patch first to confirm surface compatibility and desired result. Work in the shade on cool surfaces for even cleaning. On timber decks, scrub along the grain and rinse well. Repeat a light application rather than over concentrate for delicate areas. Important information Not recommended for raw or polished natural stone that is sensitive to cleaners. Always patch test first. Avoid use on freshly sealed surfaces. Check sealer instructions before cleaning. Keep runoff away from ponds and delicate plants. Pre wet adjacent garden beds and rinse after cleaning. Safety Wear gloves and eye protection during mixing and application. Ensure good ventilation if using in semi enclosed areas. Store upright in a cool dry place out of reach of children and pets. Specifications Size 5L concentrate Form Liquid cleaner Application Bucket, sprayer, or pressure washer Suitable areas Driveways, decks, patios, paths, outdoor walls What is in the box 1 x Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Frequently asked Will it remove oil stains Heavy oil may require a second application and some scrubbing. For long standing or deep oil, use a degreaser first, then follow with this cleaner for an even finish. Can I use it with a pressure washer Yes. Mix in the detergent tank as per the dilution guide, apply from the bottom up, allow dwell time, then rinse from the top down. Is it safe for sealed decks Patch test first and follow the sealer brand care instructions. Rinse well after cleaning. Good to pair with Outdoor deck brush or stiff broom for agitation Garden sprayer or pressure washer for fast coverage Protective gloves and safety glasses for safe handling
$27.15 $20.89
Boyle Gloss All in One Glue Sealer and Finish 236 ml Seal, glue and finish your craft projects with a single water based formula that dries clear and glossy. Boyle Gloss All in One is ideal for decoupage, paper craft, school projects and home decor. It brushes on smoothly, holds strongly and leaves a protective shine. Key benefits Three in one formula for gluing, sealing and top coating Gloss finish that dries clear and enhances colours Water based and low odour for indoor use Brushes on easily and levels well Great for beginners and experienced makers Best for Decoupage and collage Paper, card and photos Wood, MDF and craft boards Canvas and fabric accents Lightweight embellishments and mixed media Surface compatibility Use on clean, dry and dust free surfaces. Test on a small area first, especially on delicate papers, prints or dyed fabrics. How to use Prepare: Ensure the surface is clean and smooth. Cut and position your paper or embellishments. Glue: Apply a thin even coat to the surface with a soft brush. Press the item in place and smooth out any bubbles. Seal: After the glue layer sets to tack free, brush a light coat over the top. Allow to dry fully. Finish: Add 1 to 3 additional thin coats for a stronger, glossier finish. Lightly sand between coats if a super smooth result is desired. Dry time and coverage Touch dry in about 15 to 30 minutes depending on coat thickness and conditions Recoat after 30 to 60 minutes Allow 24 hours before light handling. Full cure develops over several days Coverage varies with technique. Thin coats give the best clarity and bond Clean up Wash brushes and tools with warm soapy water while wet Wipe any fresh drips with a damp cloth Tips for a glossy result Apply multiple thin coats rather than one heavy coat Work in one direction for the first coat, then cross coat for the second Use a soft synthetic brush or foam applicator to minimise brush marks Important information For indoor craft use Keep out of reach of children Avoid freezing. Store upright with the cap closed tightly Specifications Type: All in one glue, sealer and finish Finish: Gloss clear Base: Water based Size: 236 ml
$11.00
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$260.30
Dunlop Gripper Fast Tile Adhesive 500 ml Overview Dunlop Gripper Fast Tile Adhesive 500 ml is a high quality multipurpose adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials common building materials ceramics wood metals some plastics stone Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time varies with product and conditions. Allow adequate time before loading or finishing. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean uncured product with a suitable solvent or water as applicable. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. Do not ingest. Refer to the Safety Data Sheet (SDS) for full details. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$32.80
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$37.95
Product Overview: Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion. Features & Benefits: ✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors ✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes ✔️ Rapid Drying – Reduces wait times and speeds up installation ✔️ Low VOC Formula – Environmentally friendly with minimal odour ✔️ High Coverage – Approx. 5m² per litre for cost-effective application Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants. Remove loose particles and repair any cracks before application. Porous surfaces may require multiple coats for optimal adhesion. Application Instructions: Shake well before use. Apply using a brush, roller, or spray for even coverage. Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives. For highly absorbent surfaces, apply a second coat after the first has dried. Coverage: 1L covers approx. 5m² (depending on surface porosity and application method). Drying Time: Touch dry: 15-30 minutes Ready for membrane or adhesive application: 30-60 minutes Clean-Up: Clean tools immediately with warm, soapy water before the primer dries. Dispose of residue according to local waste disposal regulations. Technical Data: Type: Acrylic-based primer Colour: Milky white (dries clear) VOC Content: Low Application Temperature: +10°C to +35°C Storage: Store in a cool, dry place away from direct sunlight Safety Warnings: Avoid contact with skin and eyes; wear protective gloves and eyewear. Use in a well-ventilated area to prevent inhalation of fumes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for detailed handling information.
$55.00
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings. Surface Preparation: All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion. Priming (if required): Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane. Application Instructions: Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations. Apply the first coat using a brush or roller, working it into the surface to avoid pinholes. Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction. Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm. Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses. Allow the membrane to cure fully before tiling or overcoating. Coverage: Approximately 1.5L per square metre for two coats, depending on surface porosity. Drying Time: Tack-free: 45 minutes Recoat: 1 hour Ready for tiling: 4 hours Flood test ready: 16 hours Dry times may vary based on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based liquid rubber Colour: Grey Finish: Flexible, seamless membrane Dried Film Thickness: Approx. 1.2mm (after two coats) Application Temp: 5°C to 35°C Shelf Life: Refer to packaging for details
$124.03
$38.96
$59.65
$22.78
Bostik Contact Bond is a solvent based, high solids, brush or scaper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. Where to Use Residential Commercial Substrates Brush or Scraper Furniture and allied industries for fixing plastic laminates Flexible decorative surface coverings Materials Neoprene rubbers Porous and non-porous surfaces Wood MDF Particleboard Plywood Leather Felts Cottonback PVC Metal Features n-Hexane formula Safe quick drying Heat and water resistant Good brushability Excellent adhesion to porous and non-porous surfaces Provides an extra strong and flexible bond on contact Uses Bostik Contact Bond is a solvent based, high solids, brush or scraper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. It resists heat and water. It also provides excellent adhesion to most natural and neoprene rubbers as well as a wide variety of porous and non-porous surfaces. It may be easily applied by brush or scraper giving a secure and lasting bond making it clean and economical to use. Bostik Contact Bond is primarily used in the furniture and allied industries for fixing plastic laminates and rigid or flexible decorative surface coverings to wood, MDF, particle board, plywood, leather, felt, cotton back PVC and metal. PRODUCT CHARACTERISTICS Colour Pale yellow Viscosity Medium syrup Composition Polychloroprene rubber/resin Coverage 5 to 6m² per litre TYPICAL PERFORMANCE DATA (approx.) Touch dry Tube: 5 to 15 minutes Can: 20 to 30 minutes Full cure 45 minutes Solids content 22% Specific gravity 0.83 Heat resistance > 150°C DIRECTIONS FOR USE Read and understand the Safety Data Sheet before using this product. SDS can be acquired by visiting www.bostik.com.au or by scanning the relevant QR code on the pack. SURFACE PREPARATION Ensure all surfaces are clean and dry and free from all loose paint, dust, grease, oil and foreign materials. APPLICATION Tube (Blister Pack) Application 1. Unscrew cap and pierce and of the tube with the reverse end of the cap 2. Apply thin, even film to both surfaces to be glued 3. Leave until touch dry (approximately 5 to 15 minutes), then bring both surfaces together accurately 4. Take care to avoid the formation of air bubbles between surfaces 5. To ensure maximum adhesion, clamp or weigh down the entire surface or apply firm hand pressure evenly 6. Replace screw cap to keep the contents of tube airtight CLEANING To clean up tools, equipment and adhesive spills use Mineral Turpentine. Use Bostik Handy Wipe towels to remove adhesive from the skin. STORAGE AND SHELF LIFE Store in a cool dry place between 5°C and 30°C and out of direct sunlight. Keep away from sources of ignition. Shelf life is 12 months from the date of manufacture when stored as directed. VOC INFORMATION 606g/litre
$14.78
Davco PrimeX Multipurpose Acrylic Primer 5L is a professional-grade, water-based primer specially formulated to improve the adhesion of tile adhesives and waterproofing membranes to porous surfaces. Ideal for interior and exterior walls and floors in domestic and commercial applications, this primer ensures strong bonding performance while reducing porosity and dusting of substrates. Surface Preparation: Surfaces must be clean, dry, and free from dust, oil, grease, wax, paint, curing compounds, and other contaminants. Remove any laitance, loose materials, or previous coatings that may interfere with adhesion. On hot or windy days, dampen porous substrates lightly to avoid flash drying—but do not leave standing water. Application Instructions: Stir the primer thoroughly before use. Apply evenly using a roller, brush, broom, or squeegee in a thin, consistent layer. Allow the primer to dry fully before proceeding—drying is complete when the white, milky appearance turns clear. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Typically dries within 30–60 minutes under standard conditions. Cooler temperatures or high humidity may extend drying time. Clean Up: Clean tools and equipment with water immediately after use. Do not allow the product to dry on tools. Technical Data: Type: Acrylic-based Colour: Milky white (dries clear) Suitable for: Cement render, concrete, fibre cement sheets VOC Content: Low Packaging: 5 Litre plastic container
$88.36
Davco® Tile & Grout Cleaner is specially formulated to tackle tough dirt and stains from tiles and grout. It’s also effective in removing minor efflorescence, making it a versatile cleaner for common tiled surfaces. Key Benefits: Specially formulated ingredients Effectively cleans tiles and grout Removes minor efflorescence from grout Helps remove mould and mildew from grout surfaces Usage: Davco® Tile & Grout Cleaner is suitable for a wide range of tiled surfaces, including: Ceramic Porcelain Mosaic Quarry Slate tiles It’s ideal for removing tough dirt and stains from tiles, as well as refreshing aged grout. Packaging: Size: 1 Litre Jerry Can Colour: Clear liquid Application Steps: Mixing: Dilute Davco® Tile & Grout Cleaner with water in a clean plastic bucket at a ratio of 10 parts water to 1 part cleaner (e.g., 5L of water to 500ml of cleaner). Application: Prepare the Surface: Always wet the surface with clean water using a mop or sponge before applying the product. For Normal Cleaning: Dampen a mop or sponge with the diluted solution and wipe over the surface, then immediately rinse with clean warm water. For Heavily Soiled Areas: Apply a larger quantity of the solution and allow it to soak for up to 10 minutes. Scrub the affected area with a stiff nylon brush, then rinse thoroughly with clean warm water. Keep your tiles and grout clean, refreshed, and free from tough stains and minor efflorescence with Davco® Tile & Grout Cleaner.
$33.54
Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints. Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application. Application Instructions: For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller. For Walls: Apply using a brush, roller, or spray, ensuring even coverage. Work the material into voids to avoid pinholing. For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat. Coverage: Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete. Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage. Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage. Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use. Technical Data: Base: Acrylic Application Temperature: 10°C to 35°C Dry Film Thickness: Achieve required thickness as per application guidelines Curing Time: 24 hours before overcoating Shelf Life: Refer to packaging for details
$144.00
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)
$80.40
Safer for the environment and still does the work. The EcoConcepts Graffiti Remover is a revolutionary development in the ongoing struggle to remove paint, ink, permanent marker and unwanted graffiti from a variety of surfaces. Unlike traditional graffiti removers, EcoConcepts is environmentally-friendly and much safer for the user. Suitable for removing paint, pen, sticky residues, grease, oil, crayon, lipstick and more. Made from renewable ingredients and readily biodegradable. Contains no carcinogens, phosphates, chlorine bleach or harsh solvents. EcoConcepts represents truly green cleaning. Diluted with water it can be used on plastic, laminate, metal, carpet, most painted surfaces and whiteboards. Undiluted it will penetrate and remove graffiti from porous surfaces such as brick, stone or concrete. I’m a concentrate and nearly ready for use. Use undiluted for the toughest jobs on porous and durable surfaces. Dilute for use on less stubborn stains and less durable surfaces. Always test on an inconspicuous area first. UNDILUTED For ultimate paint and stain removal, especially on unpainted surfaces such as concrete. HIGH DILUTION Generally safe on less durable and painted surfaces – 1 part product to 5 parts water, e.g. 167mL of product makes 1L of high-dilution solution. LOW DILUTION For tougher jobs on relatively durable surfaces – 1 part product to 3 parts water, e.g. 250mL of product makes 1L of low-dilution solution.
$42.54
Gorilla Super Glue Brush & Nozzle offers 2 easy ways to dispense for control and accuracy. Brush & Nozzle features a precision tip nozzle and fine bristle brush that allow the user to control their super glue application, making it perfect for any project. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–45 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear, unlike any other super glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. Super glue, also referred to as cyanoacrylate glue, or CA glue works on a variety of materials, including plastic, metal, fabric, stone, ceramic, paper, rubber and more. It’s Gorilla tough, every time. Product Features -Two ways to dispense for greater control and versatility! -Fine bristle brush for controlled coverage with less mess -Precision tip nozzle for quick, easy dispensing -Impact Tough: Unique rubber particles increase impact resistance and strength -Fast-setting: Dries in 10-45 seconds, no clamping required. Directions -Protect Work Area From Spills -Clean and Dry Surfaces to Be Bonded -Apply Gorilla Super Glue -Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. -To use the nozzle, unscrew the upper cap and remove. To use the brush, unscrew the full cap and wipe the brush on the inner rim of the bottle to remove excess glue. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$15.00
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$40.93
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$13.11
White, metal-free, food-grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. H1 NSF Reg. No: 123004. LOCTITE® LB 8014 is a white, metal-free, food grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. It prevents friction, seizing and galling in stainless steel and other metal parts. It is temperature resistant to +400°C, has a 0 NLGI grade and is H1 NSF Registered; No: 123004. Food grade lubricant and anti-seize Metal-free Temperature resistant to +400°C NLGI Grade 0 Prevents friction, seizing and galling in stainless steel and other metal parts H1 NSF Reg. No.: 123004 LB 8014™ prevents seizing, galling, friction, and wear on threaded joints and other metal-to-metal surfaces. It is a combination of white lubricating solids and extreme pressure lubricating agents in an aluminum gelled white oil. Typical applications include pipe joints, nuts, bolts and studs, flange gaskets, slip-fit, press-fit and keyed shafts, and metal-to-metal contact involving stainless steel and other stainless alloys. It is used in industrial food industries such as meat and poultry packing plants, dairy products processing plants, canning plants, grain processing plants, sugar processing plants, bakeries, beverage plants, breweries, hospitals, and other general plant maintenance. This product is typically used in applications with an operating range of -29 °C to +400 °C. PRODUCT DESCRIPTION characteristics: Technology Anti-Seize Appearance Smooth white paste LMS Components One component - requires no mixing Cure Not applicable Application Lubrication Specific Benefits ● Lubricates, seals, and prevents galling in stainles steel joints and threaded connections ● Temperature resistant to 400 °C ● Metal free formulation Directions For Use: 1. For best performance the mating surface should be clean and free of grease. 2. Apply thin coating to threads and flats of nuts and bolts, assemble. 3. Use full strength. Do not thin.
$44.40
Neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. LOCTITE® MR 5412 is a yellow, neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. Typical applications include bonding weather stripping, insulation, rubber and trim to wood and metal. Suitable for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding Technical Information % Solids 10 Agency Approvals / Specifications CFIA Listed Colour Yellow Fixture Time 15 min. Key Characteristics Waterproof Physical Form Liquid Specific Gravity 0.88 g/l Specific Gravity Temperature 25 °C Substrates Metal, Wood Directions for use: 1. Clean surfaces thoroughly. Use abrasives to remove any powdery mold release from new weatherstripping. 2. Apply a thin, even film to both surfaces. 3. Allow to dry tacky (3 to 4 minutes). 4. Bond the two surfaces together and apply enough pressure to produce uniform contact. 5. NOTE: The early strength of LOCTITE® MR 5412 is enough to hold most parts together. However, maximum strength is obtained after the adhesive is completely dry. Aging of the bond and exposure to moderate heat increases strength.
$16.45
LOCTITE® MR 5923 is a dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. It seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. Dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. For close tolerance flanges Slow drying Flexible setting LOCTITE® MR 5923™ seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. Typical applications include solid gasket dressing, close-fitting machined surfaces, threaded connections, aviation engines, and marine engines. This product is typically used in applications with an operating range of -54 °C to +204 °C. Technology Solvent-based Chemical Type Modified resin, fillers, and alcohol Appearance Brown liquidLMS Viscosity Flow similar to SAE 10 Motor Oil Cure Air dry Application Gasketing & sealing Specific Benefit ● For close tolerance flanges ● Slow drying ● Flexible setting Chemical/Solvent Resistance LOCTITE® MR 5923™ retains effective properties in contact with water, ethylene glycol, gasoline, motor oil, transmission fluid, and seawater Directions for use: 1. Remove all previous material from mating surfaces. 2. For best results, clean and prep the area with an oil-free solvent. 3. Remove cap. Coat with a brush-top applicator. 4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of the gasket and then position it on the assembly. Coat the second side of the gasket and re-assemble. Slower drying formula increases work time. 5. Assembly is operational after 4 hours, full cure is effective after 24 hours. 6. The product can be removed from metal surfaces with isopropyl alcohol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow it to soften overnight.
$6.67
$6.94
A paint and varnish stripper free of Methylene Chloride (MC) and N-methyl Pyrollidone (NMP) for safer interior usage*. Deep penetration performance allows for multiple layers to be stripped in a single application to save time. FOR INDOOR & OUTDOOR USE Coverage: 0.5m2 per litre when applied 2mm thick on a horizontal surface. Ready to use: YES NOTE: Do not use on plastic surfaces, vinyl, masonite or rubber. Take care when using on plasterboard or other porous surfaces as softening or penetration of the surface can occur. Suitable for most decorative paints, varnishes and 1-part polyurethanes. Not for Kalsomine, penetrating timber stains or some 2-pack coatings. *in comparison with methylene chloride paint strippers • Use in a well-ventilated area and wear protective gloves and glasses. • Apply stripper approx 2mm thick using a brush. Take care on vertical or overhanging surfaces, as stripper may drip. • Leave the paint stripper in contact with the coating until softened and scrape off the coating with slight pressure. If paint remains after scraping, apply a second coat of stripper. Scrape along the grain for timber. A scourer can be used to remove ingrained paint. • Stripping times vary according to a number of paint layers, age and type. As a guide, water-based paints begin to soften after 15–20 mins. Allow 60 mins or longer for oil-based and polyurethane coatings. The paint stripper remains effective while in a wet state. • Do not allow stripper or softened paint to dry on the surface. Some oil-based paints will continue to bubble and strip even after stripper has been removed. • Wipe surface clean with a wet rag followed by a solution of Poly Sugar Soap. Do not use excessive water. On fine timber where grain swelling is likely, use methylated spirits. • Allow surfaces to completely dry before re-coating. • Clean tools in warm water. SAFETY • Risk of serious damage to eyes. • Avoid contact with skin and eyes. Wear protective gloves and glasses when mixing or using. • If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. • Avoid breathing vapour. Use in a well-ventilated area. • Wash hands after use. • Keep away from heat and ignition sources. • This product has been classified as hazardous. Refer to Safety Data Sheet for more information. • If swallowed, do NOT induce vomiting. If in eyes, wash out immediately with water. • For first aid advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor at once. Q. What is the difference between Polystrippa Paint Stripper and Polystrippa Advanced? A. Polystrippa Paint Stripper is formulated with methylene chloride. It is very aggressive and may be harmful to health with prolonged exposure. It is most suitable for smaller applications and should only be used outdoors. Polystrippa Advanced, on the other hand, is free of methylene chloride and is preferable for larger or indoor applications.
$30.88
Outdoor Timber Polish is made from natural plant oils & fragrance oils. Covers scratches, removes stains & preserves wood. • Nourishes, restores and protects outdoor furniture and woodwork. • Specifically formulated to suit Australian and New Zealand conditions. Coverage: Up to 20m2 per L Apply with: Mist on, wipe in with rag 24 hours recoat Sheen Level: Transparent Matt finish
$19.95
Prep marathon is the ultimate metal big-wig in crevices and corners. A scrub that trims down, it gets into the nooks to clean while also protecting with a silicone shield. It’s tough on calcium, rust and scale deposits which makes it ideal for use on tiles, porcelain sinks bathrooms and showers or baths. Get Prep Marathon today!
$4.00
Polishes internal furniture & joinery that has been previously waxed or oiled Suitable for Timber, concrete, slate, terracotta and stucco All-natural ingredients Apply with a lint-free cloth Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Uses: Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40m² Apply with: Lint-free cloth Number of coats: 2 Sheen level: Pale Satin
$199.00
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$25.48
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$22.35
You have seen 96 out of 102 products
Brushable adhesives, primers and cleaners for even, thin coats over edges and large surfaces (e.g., laminates, veneers, prep steps). Ensure proper coverage and flash-off/open time where required, and observe ventilation guidance. Use filters to refine by chemistry, cure/handling and clean-up. Always review the product page and TDS/SDS for instructions and safety.
