Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.
$67.73
Dunlop Builder's Bond is a high strength, multipurpose, rapid-cure epoxy bonding and repair system that joins almost any building material to almost any other. Dispensed through a self-mixing nozzle from a convenient 254ml dual cartridge, its non-sag formula holds firm on walls and even overhead, and cures stronger than concrete in about 2 hours.Where to use itSuitable for indoor and outdoor use across floor, wall and overhead repairs. Typical jobs include bonding concrete, masonry, stone, metal and timber components, rebuilding broken edges and corners, anchoring fixtures, and general structural gap filling where a fast, very strong bond is required.How to useEnsure both surfaces are clean, dry and free of dust, grease and loose material. Load the cartridge into an applicator gun, fit the self-mixing nozzle and dispense the evenly mixed epoxy directly onto the repair or bond line. Shape and tool it before it stiffens. Once cured, Builder's Bond can be shaped, sanded, drilled and painted, so repairs can be blended invisibly into the surrounding surface.Important notesNew concrete must be fully cured - a minimum of 28 days old - before bonding. The non-sag consistency suits vertical and overhead work but is not a pourable grout. Start a fresh nozzle for each session, as mixed product hardens inside the nozzle.Specifications Size 254ml dual cartridge Coverage Depends on bead size and gap width Substrates Concrete, masonry, stone, metal, timber and most building materials Set time Stronger than concrete in 2 hours Finish Sandable, drillable and paintable once cured SafetyUncured epoxy resins and hardeners can cause skin irritation and sensitisation. Wear nitrile gloves and eye protection, ventilate the work area, avoid skin contact and wash immediately if contact occurs. Keep cartridges sealed and out of reach of children.
$61.79
Dunlop Primer & Additive is a ready-to-use liquid primer that boosts the grip between your substrate and the Dunlop products that go on top of it. Whether you are about to level a floor, lay tiles or roll out a waterproofing membrane, a quick coat of this milky-white liquid seals porous surfaces and gives adhesives, levellers and membranes a far stronger key to bond to. It doubles as a grout additive, improving flexibility, adhesion, colour depth and resistance to abrasion and staining.Where to use itSuitable for both indoor and outdoor projects, on walls and floors. Use it over concrete, cement sheet, fibre-cement, plasterboard, sheeting and timber before applying Dunlop tile adhesives, floor preparation products or waterproofing membranes.How to useMake sure the surface is clean, dry and free of dust or contaminants. Apply undiluted before waterproofing, tiling and timber floor preparation; dilute it for priming wall board. On large floor areas a household broom works well to spread the primer and push it into the surface. Allow it to dry clear before continuing with your adhesive, leveller or membrane. Tools rinse out in water while the product is still wet.Important notesCoverage varies with the porosity of the substrate. The primer goes on white and dries clear, so you can easily see where you have already coated. Highly porous surfaces may need extra material.Specifications Size 1 litre bottle Coverage Approx. 4m² per litre undiluted; approx. 8m² per litre diluted Substrates Concrete, cement sheet, fibre-cement, plasterboard, timber Colour Applies white, dries clear SafetyWork in a ventilated area, avoid contact with skin and eyes, and keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.50
Dunlop Ardit Feather Finish is a cement-based smoothing compound that skims internal floors to a super-smooth, permanent finish before floor coverings are installed. Powered by ARDEX Ardit technology, it trowels out to a true feather edge and sets so fast that coverings can be applied from just 15 minutes after placement - and it needs no primer on most surfaces, saving a whole step.Where to use itFor indoor use over concrete, existing tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. It is ideal for filling grout joints when covering old tiles with vinyl, smoothing trowel marks in levellers, and taking out minor imperfections before vinyl, carpet or ceramic tiles.How to useEnsure the floor is clean, sound and free of dust, grease and loose material. Mix the powder with clean water to a smooth, creamy paste and apply with a flat steel trowel, working from a feather edge up to 3mm thick. Tight second coats can be applied as the first firms. Any ridges can be shaved or lightly sanded once set for a flawless surface.Important notesIndoor use only and must be covered by a floor covering. Mix small batches to suit the rapid set. No primer is required over common substrates - check the datasheet for unusual surfaces.Specifications Size 3.5kg bag Coverage Approx. 12m² over concrete or 24.5m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyCement powders can irritate eyes, skin and lungs. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated, avoid prolonged contact with the wet compound and wash hands after use. Store out of reach of children.
$82.46
Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications Size 8kg bag Coverage Approx. 27m² over concrete or 55m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.
$125.51
Dunlop Level-Flex Timber Floor Leveller is a high performance, partially self-smoothing latex levelling screed developed specifically for timber floors. Supplied as a complete two-part kit in a handy pail, it combines a cement-based powder with a flexible latex liquid to deliver the adhesion, flexibility and water resistance needed when levelling over floors that move more than concrete does.Where to use itDesigned for indoor use over timber and concrete subfloors, it creates a smooth, flat surface ready for ceramic tiles, carpet or vinyl. It is a popular choice for renovating older homes with uneven timber floorboards or sheet flooring before new coverings are installed.How to useSand and prime timber floors first, and prime porous concrete with a plush broom application. Blend the latex liquid with the powder using a low-speed paddle mixer until smooth, then pour and spread with a trowel, allowing the screed to flow out and self-smooth. The floor is walkable in about 3 hours; lay ceramic tiles after roughly 12 hours (3mm screed), carpet after 24 hours and vinyl after 48 hours.Important notesIndoor use only, and the leveller must be covered by a finished floor covering. Timber must be sound, rigid and well fixed before levelling. Low odour formula makes it comfortable to use in occupied homes.Specifications Size 15.9kg kit (powder plus latex liquid) Coverage Approx. 7m² at 1mm or 2.3m² at 3mm per kit Thickness Feather edge to approx. 12mm (thicker with aggregate) Substrates Timber and concrete Walk-on time 3 hours SafetyWear gloves, safety glasses and a P2 dust mask when handling the cement powder, and keep the room ventilated while mixing. Avoid skin and eye contact with the wet mix, wash after use and store the kit away from children.
$108.45
Dunlop Ardit Timber Floor Leveller is a high performance, partially self-smoothing screed for timber floors, built on ARDEX Ardit technology. Unlike traditional two-part latex levellers, it is a convenient single-part formula - just add water - yet still delivers the excellent adhesion, flexibility and water resistance needed to level over timber substrates that flex underfoot.Where to use itFor indoor use over timber and concrete subfloors, creating a smooth, even base before installing ceramic tiles, carpet or vinyl. It is well suited to renovations where old floorboards or sheet flooring need flattening before new coverings are laid.How to useSand and prime all timber floors before application, and prime porous surfaces such as concrete using a plush broom. Mix the powder with clean water using a low-speed paddle mixer until smooth and lump free, then pour, spread with a trowel and let the screed flow out to a level finish. Apply from a feather edge up to 12mm neat, or up to 30mm with the addition of 2-5mm aggregate.Important notesIndoor use only and must be covered with a finished floor covering. Ensure timber floors are rigid and securely fixed before levelling. The no-odour formula suits occupied homes. Check the technical datasheet for covering wait times for your chosen flooring.Specifications Size 16kg kit Coverage Approx. 10m² at 1mm or 3m² at 3mm per kit Thickness 0-12mm neat; 12-30mm with aggregate Substrates Timber and concrete SafetyThe cement-based powder is alkaline and dusty when dry. Wear gloves, eye protection and a P2 dust mask while mixing, ventilate the work area, avoid contact with skin and eyes, and wash thoroughly after use. Keep away from children and pets.
$105.25
Tarzan's Grip Wood Glue is a fast, dependable PVA timber adhesive built for everyday woodworking and repairs around the home and workshop. This 250mL bottle delivers a strong, lasting bond on a wide range of timbers, making it a reliable choice for cabinetry, joinery, furniture assembly and general carpentry jobs. The water-based PVA formula spreads smoothly, penetrates porous timber and sets to a tough, near-invisible bond line. Its extended working time gives you room to align and clamp pieces accurately before the glue grabs, while easy water clean-up keeps the job tidy with no harsh solvents. What it bondsIdeal for softwoods, hardwoods, plywood and MDF, and well suited to bonding porous materials to one another. Where to use itIndoor / Interior: furniture making and repair, cabinet and drawer assembly, joinery, trim and moulding, hobby and craft woodwork.Outdoor: this is an interior-grade wood glue and is not intended for fully weather-exposed or submerged applications. How to use it Make sure both surfaces are clean, dry and free of dust, grease and old finish. Apply an even coat of glue to one or both mating surfaces. Bring the parts together, align, and clamp firmly. Wipe away any squeeze-out with a damp cloth before it dries. Leave clamped until set, then allow full cure before stressing the joint. Important notesFor interior use only. Not classified as hazardous or as a dangerous good. Keep the cap closed between uses and store upright. Best results on clean, well-fitted joints with adequate clamping pressure. Specifications Brand Tarzan's Grip Product Wood Glue (PVA) Size 250mL Form Liquid Colour Light yellow Base Water-based PVA Density 1.05 g/cm³ pH 3.5 - 4.5 Clean up Water (while wet) Suitable for Softwoods, hardwoods, plywood, MDF Use area Interior SafetyBased on available information this product is not classified as hazardous under Safe Work Australia GHS criteria, and is not classified as a Dangerous Good for transport. Avoid eye contact and repeated or prolonged skin contact, and avoid inhaling mist or vapour. Wash hands after use and keep away from food and drink. If in eyes, rinse immediately with water; if swallowed, rinse mouth, do not induce vomiting, and seek medical advice. Store in a cool, dry, well-ventilated place out of direct sunlight and away from heat or ignition sources. Keep out of reach of children. Refer to the manufacturer's current Safety Data Sheet for full handling guidance.
$33.75
Loctite EA 9235 (Five Minute E-Pox-E, item EFQ5) is a fast-acting two-part epoxy that mixes resin and hardener in equal parts to form a tough, rigid, high-strength bond in about five minutes. Supplied in a dual-barrel syringe that dispenses both components in the correct 1:1 ratio every time, it is ideal for fast permanent repairs and multi-piece projects across a wide range of household, workshop and trade materials. Once cured it resists water and most common solvents, and can be sanded, drilled and machined. It can also be used as a versatile filler for gap filling, surface repairs and laminating. Bonds: metal, glass, ceramic, china, tile, stone, concrete, wood, fibreglass and most rigid plastics. Where to use it Indoor: repairing ceramics, china and glassware, fixing tools and toys, bonding tiles, and general household and hobby repairs. Outdoor: bonding stone, concrete and masonry, plus garden and workshop repairs. Not recommended for continuously wet areas or prolonged water immersion. How to use 1. Make sure surfaces are clean, dry and free of oil, wax, paint and rust. Roughen smooth surfaces by sanding for a stronger grip. 2. Remove the plug and cut the syringe tip at the marked opening. Stand the syringe upright and press the plunger gently to expel any air. 3. Depress the double plunger to dispense equal parts of resin and hardener onto a disposable surface, then mix thoroughly for about one minute. 4. Apply to both surfaces within one to two minutes of mixing and press together. Support the join for around 10 minutes. 5. Usable strength is reached in about 1 hour and the bond fully cures in 24 hours. Wipe the tips clean and replace the plug for storage. Clean uncured adhesive with acetone before it sets. Cured adhesive can be carefully cut away with a sharp blade. Important notes Not recommended for polyethylene, polypropylene, nylon, non-stick coatings or flexible materials. Not suitable for potable (drinking) water systems, prolonged water immersion, or short-term heat above 150°C. Apply between 4°C and 35°C. Specifications Part number Loctite EA 9235 / EFQ5 Size 25ml dual syringe Chemistry Two-part epoxy (epoxy resin / polymercaptan hardener) Mix ratio 1:1 by volume Set time Approx. 5 minutes Usable strength Approx. 1 hour Full cure 24 hours Cured colour Clear amber Hardness 80 Shore D Service temperature -23°C to 49°C continuous (up to 150°C intermittent) Water resistant Yes Sandable / machinable Yes Paintable No Shelf life 24 months unopened Safety Contains epoxy resin and polymercaptan/amine hardeners. Causes skin and eye irritation and may cause an allergic skin or respiratory reaction. Wear gloves, work in a well-ventilated area and avoid breathing vapours. For eye contact, rinse with water for 15 minutes and seek medical advice. If swallowed, do not induce vomiting and seek medical advice. Keep out of reach of children. Always refer to the Safety Data Sheet before use.
$33.75
Endeavour QuickDeck is a premium water-based decking oil from Prep Productions, built for people who want a protected deck without the long dry times and strong odour of traditional solvent oils. Its oil-modified acrylic resin defends exterior timber on three fronts: it blocks moisture penetration, resists fungal growth and shields the boards from UV damage. Because it is water based, it dries fast, has low odour and low VOC content, and tools wash out in water. The 10 litre pail is the bulk pack, suited to large decks and full exterior timber projects, and covers up to roughly 140 square metres per coat at the maximum spread rate.Formula overviewAn oil-modified acrylic formula in a water base: a blend of water-soluble polymer resins refined to combine the penetrating character of an oil with the quick, low-odour convenience of an acrylic. The liquid is lightly coloured and dries to a transparent matt finish that lets the timber grain show through.Where to use itOutdoor: decks, garden furniture, pergolas, fences, gates and other exterior timbers.Indoor: not intended for interior floors or furniture. This is an exterior decking finish.How to use Stir well before use, as the product may settle on standing. Prepare the surface first: new or weathered boards should be cleaned with Endeavour Timber Deck Cleaner and allowed to dry. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 14 square metres per litre depending on timber porosity. Wash tools in water immediately after use. Important notes The finish is transparent matt: it enhances the timber tone but will not give an opaque colour. Apply in dry weather and avoid application if rain is expected before the coating has dried. Check the label for temperature and weather guidance. Results depend on preparation: grey, weathered timber should be cleaned back to sound wood first. Specifications Size 10 litres Base Water-based oil-modified acrylic, low VOC Coats 2 Recoat time 24 hours Coverage Up to 14 m² per litre Finish Transparent matt Application Brush or lambswool applicator Clean up Water Made in Australia SafetyNot classified as hazardous and not flammable. At most it may cause mild, short-lived skin or eye irritation, so gloves and eye protection are still sensible for prolonged use. Use in a well-ventilated area. If swallowed, do not induce vomiting, rinse the mouth, drink water and contact the Poisons Information Centre on 13 11 26 if symptoms develop. May settle or separate on standing, so stir before use, and prevent large spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$229.50
Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 5.2kg pail is the trade size for lining whole rooms.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the pail, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the pail label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the pail label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 5.2kg pail Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyNot classified as hazardous and not a scheduled poison. The paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. If it gets in the eyes, irrigate with water for 15 minutes and seek medical attention; skin washes clean with warm soapy water. If swallowed, rinse the mouth, drink water, do not induce vomiting and seek medical advice. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$33.20
Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 1kg tub suits patch jobs and small lining work.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the tub, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the tub label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the tub label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 1kg tub Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyNot classified as hazardous and not a scheduled poison. The paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. If it gets in the eyes, irrigate with water for 15 minutes and seek medical attention; skin washes clean with warm soapy water. If swallowed, rinse the mouth, drink water, do not induce vomiting and seek medical advice. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$17.90
Endeavour QuickDeck is a premium water-based decking oil from Prep Productions, built for people who want a protected deck without the long dry times and strong odour of traditional solvent oils. Its oil-modified acrylic resin defends exterior timber on three fronts: it blocks moisture penetration, resists fungal growth and shields the boards from UV damage. Because it is water based, it dries fast, has low odour and low VOC content, and tools wash out in water. The 4 litre pack covers a typical family-sized deck with two coats.Formula overviewAn oil-modified acrylic formula in a water base: a blend of water-soluble polymer resins refined to combine the penetrating character of an oil with the quick, low-odour convenience of an acrylic. The liquid is lightly coloured and dries to a transparent matt finish that lets the timber grain show through.Where to use itOutdoor: decks, garden furniture, pergolas, fences, gates and other exterior timbers.Indoor: not intended for interior floors or furniture. This is an exterior decking finish.How to use Stir well before use, as the product may settle on standing. Prepare the surface first: new or weathered boards should be cleaned with Endeavour Timber Deck Cleaner and allowed to dry. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 14 square metres per litre depending on timber porosity. Wash tools in water immediately after use. Important notes The finish is transparent matt: it enhances the timber tone but will not give an opaque colour. Apply in dry weather and avoid application if rain is expected before the coating has dried. Check the label for temperature and weather guidance. Results depend on preparation: grey, weathered timber should be cleaned back to sound wood first. Specifications Size 4 litres Base Water-based oil-modified acrylic, low VOC Coats 2 Recoat time 24 hours Coverage Up to 14 m² per litre Finish Transparent matt Application Brush or lambswool applicator Clean up Water Made in Australia SafetyNot classified as hazardous and not flammable. At most it may cause mild, short-lived skin or eye irritation, so gloves and eye protection are still sensible for prolonged use. Use in a well-ventilated area. If swallowed, do not induce vomiting, rinse the mouth, drink water and contact the Poisons Information Centre on 13 11 26 if symptoms develop. May settle or separate on standing, so stir before use, and prevent large spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$89.95
Endeavour QuickDeck is a premium water-based decking oil from Prep Productions, built for people who want a protected deck without the long dry times and strong odour of traditional solvent oils. Its oil-modified acrylic resin defends exterior timber on three fronts: it blocks moisture penetration, resists fungal growth and shields the boards from UV damage. Because it is water based, it dries fast, has low odour and low VOC content, and tools wash out in water.Formula overviewAn oil-modified acrylic formula in a water base: a blend of water-soluble polymer resins refined to combine the penetrating character of an oil with the quick, low-odour convenience of an acrylic. The liquid is lightly coloured and dries to a transparent matt finish that lets the timber grain show through.Where to use itOutdoor: decks, garden furniture, pergolas, fences, gates and other exterior timbers.Indoor: not intended for interior floors or furniture. This is an exterior decking finish.How to use Stir well before use, as the product may settle on standing. Prepare the surface first: new or weathered boards should be cleaned with Endeavour Timber Deck Cleaner and allowed to dry. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 14 square metres per litre depending on timber porosity. Wash tools in water immediately after use. Important notes The finish is transparent matt: it enhances the timber tone but will not give an opaque colour. Apply in dry weather and avoid application if rain is expected before the coating has dried. Check the label for temperature and weather guidance. Results depend on preparation: grey, weathered timber should be cleaned back to sound wood first. Specifications Size 1 litre Base Water-based oil-modified acrylic, low VOC Coats 2 Recoat time 24 hours Coverage Up to 14 m² per litre Finish Transparent matt Application Brush or lambswool applicator Clean up Water Made in Australia SafetyNot classified as hazardous and not flammable. At most it may cause mild, short-lived skin or eye irritation, so gloves and eye protection are still sensible for prolonged use. Use in a well-ventilated area. If swallowed, do not induce vomiting, rinse the mouth, drink water and contact the Poisons Information Centre on 13 11 26 if symptoms develop. May settle or separate on standing, so stir before use, and prevent large spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.95
Endeavour Timber Deck Cleaner is the preparation step before oiling any deck, new or old. It is a triple-action, water-based cleaner from Prep Productions' Endeavour range that cleans away grime, grease, mould, algae and mildew, restores stained and dirty boards to sound timber, and rejuvenates grey, weathered decks so they brighten back towards their natural colour. On new boards it strips out natural tannins, helping your decking oil penetrate evenly and last longer. The 4 litre pack is sized for full decks and repeat seasonal cleans.Formula overviewA water-based solution whose two key actives work together: oxalic acid brightens the timber and lifts tannin staining, while benzalkonium chloride, a biocide, deals with mould, algae and mildew. The concentrate is a pale, clear liquid that dilutes in water for application.Where to use itOutdoor: all new and weathered exterior timber, with decks the headline use. Also suited to preparing other exterior timber surfaces before finishing.Indoor: not intended for interior surfaces. This is an exterior timber preparation product.How to use Dilute with water as directed on the pack label. Apply the diluted solution with a deck scrub, working it into the boards. Rinse thoroughly and allow the timber to dry before oiling. Follow the label for contact time and drying guidance. Coverage is 5 to 10 square metres per litre when diluted, depending on timber porosity and texture. Important notes This is a Schedule 6 poison. Store it tightly closed, away from children and pets. Wear gloves and protective clothing: the concentrate is harmful in contact with skin and if swallowed. Prevent runoff entering drains, garden beds or waterways, and rinse surrounding plants with water if splashed. May settle on standing; stir before use. Specifications Size 4 litres Base Water-based, oxalic acid and benzalkonium chloride actives Coverage 5 to 10 m² per litre diluted Application Deck scrub Clean up Water Made in Australia SafetySchedule 6 poison. Harmful if swallowed and harmful in contact with skin. Wear rubber or nitrile gloves and eye protection, avoid contact with skin, eyes and clothing, and do not eat, drink or smoke while using. If swallowed, do not induce vomiting, rinse the mouth and call the Poisons Information Centre on 13 11 26 or a doctor. For skin contact, wash with warm soapy water for 10 to 20 minutes and remove contaminated clothing; for eyes, flush with lukewarm water and seek advice if irritation persists. Not flammable. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$39.95
Endeavour Timber Deck Cleaner is the preparation step before oiling any deck, new or old. It is a triple-action, water-based cleaner from Prep Productions' Endeavour range that cleans away grime, grease, mould, algae and mildew, restores stained and dirty boards to sound timber, and rejuvenates grey, weathered decks so they brighten back towards their natural colour. On new boards it strips out natural tannins, helping your decking oil penetrate evenly and last longer.Formula overviewA water-based solution whose two key actives work together: oxalic acid brightens the timber and lifts tannin staining, while benzalkonium chloride, a biocide, deals with mould, algae and mildew. The concentrate is a pale, clear liquid that dilutes in water for application.Where to use itOutdoor: all new and weathered exterior timber, with decks the headline use. Also suited to preparing other exterior timber surfaces before finishing.Indoor: not intended for interior surfaces. This is an exterior timber preparation product.How to use Dilute with water as directed on the pack label. Apply the diluted solution with a deck scrub, working it into the boards. Rinse thoroughly and allow the timber to dry before oiling. Follow the label for contact time and drying guidance. Coverage is 5 to 10 square metres per litre when diluted, depending on timber porosity and texture. Important notes This is a Schedule 6 poison. Store it tightly closed, away from children and pets. Wear gloves and protective clothing: the concentrate is harmful in contact with skin and if swallowed. Prevent runoff entering drains, garden beds or waterways, and rinse surrounding plants with water if splashed. May settle on standing; stir before use. Specifications Size 1 litre Base Water-based, oxalic acid and benzalkonium chloride actives Coverage 5 to 10 m² per litre diluted Application Deck scrub Clean up Water Made in Australia SafetySchedule 6 poison. Harmful if swallowed and harmful in contact with skin. Wear rubber or nitrile gloves and eye protection, avoid contact with skin, eyes and clothing, and do not eat, drink or smoke while using. If swallowed, do not induce vomiting, rinse the mouth and call the Poisons Information Centre on 13 11 26 or a doctor. For skin contact, wash with warm soapy water for 10 to 20 minutes and remove contaminated clothing; for eyes, flush with lukewarm water and seek advice if irritation persists. Not flammable. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$13.95
Oz-Oil Decking Oil is a multipurpose exterior timber oil from Prep Productions, pitched as a five-in-one product: one can covers your deck, outdoor furniture, pergola, fences and gates. Blended from natural plant oils, it soaks into the timber to preserve and seal it from within, leaving a natural, semi-transparent appearance rather than a glossy film. A practical bonus for occasional users: the manufacturer states it is non-evaporative and will not gel in the can, so leftover oil keeps for the next job rather than going to waste.Formula overviewA blend of natural seed oils and waxes carried in dipentene, a citrus-derived solvent. The oil is lightly pigmented and semi-clear with a citrus odour, and works by penetrating the boards rather than coating them.Where to use itOutdoor: external timber including decking, cladding, railings, joists, bearers, rafters, pergolas, garden furniture, fences and gates.Indoor: not intended for interior use. This is an exterior timber oil.How to use Stir well before use, as the oils may settle in the can. Make sure the timber is clean, dry and free of old coatings. Follow the can label for preparation guidance. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 12 square metres per litre depending on timber porosity. Important notes The finish is semi-transparent. It enriches the timber tone but will not deliver an opaque or solid colour. Like all penetrating oils, results depend on surface preparation. Weathered grey timber should be cleaned back to sound wood first. Check the can label for clean-up directions and detailed preparation steps. Specifications Size 4 litres Base Natural seed oils and waxes in citrus-derived dipentene Coats 2 Recoat time 24 hours Coverage Up to 12 m² per litre Finish Transparent matt, natural semi-transparent tone Application Brush or lambswool applicator Shelf life Non-evaporative, does not gel in the can Made in Australia SafetyCombustible liquid (flash point around 68°C). Keep away from heat, sparks and open flames, and store below 30°C, tightly closed, in a well-ventilated area away from strong oxidisers. Rags soaked in decking oil can self-heat and spontaneously combust: lay used rags flat to dry outdoors or soak them in water before disposal. May irritate skin and can cause an allergic skin reaction in people sensitised to citrus solvents, so wear gloves when applying. If swallowed, do not induce vomiting, rinse the mouth and call the Poisons Information Centre on 13 11 26. Toxic to aquatic life: prevent washings and spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$64.68
Organoil Woodguard is a deeply penetrating oil treatment made to look after brand-new exterior timber in the period between installation and final finishing. Fresh hardwood often carries high moisture and, left bare, can cup, split, crack or bleed tannins as it dries out. Woodguard soaks into the boards and stabilises them while they acclimatise, so the timber arrives at oiling day in sound, even condition. It is made in Australia by Prep Productions and formulated for harsh Australian and New Zealand exposure.Formula overviewA natural-oil blend built around tung oil and beeswax, carried by dipentene, a citrus-derived solvent. Rather than forming a film on top of the wood, the blend penetrates the timber surface, which is why it is applied as a single coat and later over-coated with a finishing oil.Where to use itOutdoor: new, raw timber decking, joists, bearers, cladding, posts, rails and exterior joinery. Particularly recommended for dense or high-moisture hardwoods such as spotted gum and plantation species before they are oiled.Indoor: not intended for interior finishing. Woodguard is an exterior pre-treatment, not a furniture or floor finish.How to use Stir well before use, as natural oils can settle. New raw timber can be treated directly. Timber that has already weathered in the elements should first be cleaned with a timber wash such as Organoil Wash-A-Way. Apply one coat only, using a brush or lambswool applicator. Coverage is up to 12 square metres per coat depending on timber density and porosity. Allow the treatment to dry fully before applying your finishing oil. Follow the can label for drying guidance. Important notes Woodguard is an interim protectant, not a final finish. Plan to apply a decking or exterior timber oil afterwards. Designed as a one-coat application. Do not over-apply. For new or raw untreated timber only. Previously coated timber should be stripped and washed first. Specifications Size 4 litres Base Solvent-borne natural oils (tung oil, beeswax, citrus-derived dipentene) Coats 1 Coverage Up to 12 m² per coat Finish Matt, natural Application Brush or lambswool applicator Made in Australia SafetyCombustible liquid (flash point around 61°C). Keep away from heat, sparks and open flames, and store below 30°C in a tightly closed container in a well-ventilated area. Rags and applicators soaked in this product can self-heat and spontaneously combust: lay used rags flat to dry outdoors or soak them in water before disposal. May be fatal if swallowed and enters airways; do not induce vomiting, rinse the mouth and call the Poisons Information Centre on 13 11 26. May irritate skin and eyes and can cause an allergic skin reaction in sensitised people, so wear gloves and eye protection. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$84.56
Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Blast away built up grime, dirt, and weather stains across large outdoor areas with this powerful concentrate. Designed for Aussie backyards, it cuts through tough mess on concrete, pavers, brick, tiles, and timber or composite decks so outdoor spaces look fresh and inviting again. Why you will love it Heavy duty clean that tackles road film, mildew stains, leaf tannins, and greasy marks. Concentrated value so one bottle makes multiple buckets of ready to use solution. Fast results with minimal scrubbing on most surfaces. Versatile for driveways, decks, paths, patios, and outdoor walls. Hose or pressure washer friendly for quick coverage on big jobs. Ideal surfaces Concrete driveways and garage floors Pavers, brick, stone, and outdoor tiles Timber decks and composite decking Rendered walls and fencing Outdoor furniture settings made of hard materials Dilution guide Job type Mix ratio Where to use Heavy build up 1 part cleaner to 4 parts water Oil spots, mildew stains, leaf marks on concrete and pavers General cleaning 1 part cleaner to 10 parts water Routine driveway and deck washes Maintenance 1 part cleaner to 20 parts water Frequent quick cleans and large areas Coverage: A 5L concentrate can make many litres of solution and clean a large area depending on dilution, surface porosity, and soil level. How to use Sweep the area to remove loose debris. Mix to the required ratio in a bucket or pressure washer reservoir. Wet the surface, then apply generously with a garden sprayer, watering can, mop, or pressure washer. Allow 3 to 5 minutes contact time. Do not let the solution dry on the surface. Agitate stubborn spots with a stiff outdoor broom or deck brush. Rinse thoroughly with a hose or pressure washer, pushing residue to drainage. Tips for best results Test on a small hidden patch first to confirm surface compatibility and desired result. Work in the shade on cool surfaces for even cleaning. On timber decks, scrub along the grain and rinse well. Repeat a light application rather than over concentrate for delicate areas. Important information Not recommended for raw or polished natural stone that is sensitive to cleaners. Always patch test first. Avoid use on freshly sealed surfaces. Check sealer instructions before cleaning. Keep runoff away from ponds and delicate plants. Pre wet adjacent garden beds and rinse after cleaning. Safety Wear gloves and eye protection during mixing and application. Ensure good ventilation if using in semi enclosed areas. Store upright in a cool dry place out of reach of children and pets. Specifications Size 5L concentrate Form Liquid cleaner Application Bucket, sprayer, or pressure washer Suitable areas Driveways, decks, patios, paths, outdoor walls What is in the box 1 x Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Frequently asked Will it remove oil stains Heavy oil may require a second application and some scrubbing. For long standing or deep oil, use a degreaser first, then follow with this cleaner for an even finish. Can I use it with a pressure washer Yes. Mix in the detergent tank as per the dilution guide, apply from the bottom up, allow dwell time, then rinse from the top down. Is it safe for sealed decks Patch test first and follow the sealer brand care instructions. Rinse well after cleaning. Good to pair with Outdoor deck brush or stiff broom for agitation Garden sprayer or pressure washer for fast coverage Protective gloves and safety glasses for safe handling
$27.15 $20.89
Get crisp, professional paint lines with Wagner Mask-It. This painter’s masking tape is designed to seal neatly along the edge, reduce paint bleed, and remove cleanly when the job is done. Ideal for walls, trim, skirting boards, window frames, and any detail work where a sharp finish matters. Key Benefits Clean paint edges that help minimise bleed on most interior surfaces. Easy application with a smooth unwind and hand tearable backing. Clean removal when used as directed on properly prepared surfaces. Works with brushes, rollers, and spray for DIY and trade jobs. Perfect For Cutting in around ceilings, cornices, and trims Protecting hardware, switches, and fittings Two tone feature walls and accent colours Masking glass, tiles, and metal fixtures during repainting Surface Compatibility Use on properly prepared, fully cured interior paint, primed timber, metal, glass, and most smooth surfaces. Always test in an inconspicuous area first. How To Use Prep the surface: Ensure it is dry, dust free, and fully cured. Apply the tape: Press down firmly along the edge with a putty knife or fingernail to seal. Paint: Roll or brush away from the tape edge for best results. Remove: Peel back slowly at a 45 degree angle while paint is still slightly tacky, unless your coating specifies otherwise. Pro Tips Burnish the tape edge lightly to improve the seal on textured areas. Apply light coats near the edge. Heavy wet coats can overwhelm any mask. For long runs, overlap tape pieces by a few millimetres and press the overlap firmly. Good To Know Suitable for indoor projects and general decorating. Store in a cool, dry place away from direct sunlight to maintain performance. Available in popular widths to suit trim work and broad masking. Frequently Asked Questions Will it pull off fresh paint?Only apply to fully cured paint. Cure times vary by product and conditions. When in doubt, allow extra time and test first. Does it work on lightly textured walls?Yes, on many light textures, but press down firmly along the edge and use lighter coats near the tape line. Can I use it with spray equipment?Yes. Apply, seal the edge, and use controlled passes. Avoid flooding the tape line.
$14.80 $12.65
Bear PVC Duct Tape is a tough, reliable, all purpose tape that delivers a strong hold and a clean finish for quick fixes. Ideal for sealing, bundling, patching, and general repairs at home, on site, and in the workshop. Its PVC backing resists moisture and abrasion, while the high tack adhesive bonds to a wide range of surfaces for dependable results. Why you will love it Fast grab for instant hold on contact Durable PVC backing resists scuffs, tears, and everyday wear Moisture resistant for confident indoor and short term outdoor use Conformable backing wraps neatly around pipes, ducts, and irregular shapes Easy to tear by hand for quick application without tools Low residue when removed from most clean surfaces Great for Sealing HVAC duct joins and flexible ducting Temporary patching of plastic sheeting, tarps, and covers Bundling cables, mats, and lightweight components Edge protection on cartons and packing jobs Quick fixes on site and around the home Works on Metal, plastic, vinyl, painted surfaces, cardboard, glass, masonry, timber, and more. For best results, surfaces should be clean, dry, and free of dust or oils. How to use Prepare the surface by cleaning off dust, grease, and moisture. Measure and tear the required length. Scissors are optional. Apply the tape with firm pressure, smoothing from the center outward to remove air pockets. Reinforce high stress areas with overlapping strips as needed. Pro tips Apply at room temperature for the best initial tack. On porous or rough surfaces, use extra pressure or a primer for maximum bond. For long term outdoor exposure, consider overcoating edges to limit water ingress. Typical specifications Backing PVC Adhesive Rubber based Total thickness Approx. 0.16 to 0.20 mm Temperature range Approx. −10 °C to +60 °C Finish Matte PVC Common sizes 48 mm width, 30 m length and other widths as available Colour Silver or Black depending on variant Values above are typical for PVC duct tapes and may vary by batch and width. FAQs Can I use it outdoorsYes for short term jobs. For permanent outdoor sealing, select a tape rated for UV and long term weather exposure. Will it remove cleanlyOn smooth, sealed surfaces it often removes with minimal residue. Always test on an inconspicuous area first. Is it suitable for high heatPVC duct tape is best within the stated temperature range. For sustained high temperature applications, choose a foil or specialty HVAC tape. Why buy from Glues Australia Trusted Australian supplier with fast dispatch Helpful support if you need sizing or product advice
$12.68 $9.27
Speed up your painting prep with UNi-PRO Pre Taped Masking Film. This convenient roll combines quality painter’s tape with a static-cling masking film that drapes cleanly and stays put, helping you protect trims, skirting, windows, and furniture while you cut in and roll. Perfect for quick room refreshes, touch ups, and full repaints. Why you'll love it Two in one tape and film for fast, tidy masking Static cling helps the film hug surfaces and reduce paint bleed Clean removal on most surfaces when applied to sound, cured paint 550 mm drop ideal for architraves, skirting boards, window frames, and small appliances 25 m length gives generous coverage for multiple areas Suitable for brushes and rollers with water based and most solvent based paints Best for Trims, doors, window frames, skirting boards Protecting benchtops, splashbacks, and appliances during repainting Quick masking on rentals and maintenance jobs How to use Ensure the surface is dry, dust free, and fully cured. Apply the taped edge along the line you want to protect, pressing down firmly. Unfold the film so it drapes over the area. Static cling will help it stay in place. Paint as normal. Allow paint to become touch dry. Peel tape back slowly at a 45 degree angle to remove. Size and coverage Width: 550 mm drop Length: 25 m roll Approximate coverage: up to 13.75 m² of drape (when fully unfolded) Specifications Brand UNi-PRO Product type Pre taped masking film Film material High density polyethylene with static cling Tape type Painter’s masking tape Paint compatibility Water based and most solvent based paints Surface compatibility Painted timber, plasterboard, metal, glass, tiles, laminates Dimensions 550 mm x 25 m Pack contents 1 roll
$14.43 $11.68
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$57.40 $40.04
Get a clean, hardware free look with T-Rex Clear Double Sided Tape. This high performance clear mounting tape creates a strong, permanent bond for photos, hooks, cable clips, house numbers, trims, and light decor. It is ideal when you want the hold without the hardware and a finish that stays virtually invisible on glass, tiles, metal, and painted walls. Why you will love it Crystal clear finish that helps hide the fix for a neat result Strong permanent bond for everyday mounting and craft projects Moisture and UV resistant construction for long lasting performance Instant stick with pressure activation, no curing time required No tools needed, peel and stick application Great for Mounting signage, house numbers, and name plates Securing cable clips and small hooks Fixing splashback trim and edging Crafts, scrapbooking, and photo boards Temporary holding during light assembly Works on Glass and mirrors Glazed tiles and ceramics Metal, aluminium, and stainless steel Finished timber and laminate Painted walls that are sound, clean, and fully cured Most rigid plastics except low surface energy plastics Note: Not recommended for wallpaper, delicate or dusty surfaces, or low surface energy plastics such as PE, PP, and PTFE. Always test on a small area first. How to use Prepare the surface. Clean with isopropyl alcohol and let dry. Remove dust, grease, and loose paint. Apply tape. Cut to length. Apply tape to the lightest item first. Press firmly along the whole strip. Peel liner. Remove the protective liner without touching the adhesive. Mount. Position carefully. Press firmly for 30 to 60 seconds to activate the bond. Maximum strength develops with time under steady pressure. Removal tips Warm gently and peel back slowly at a low angle Use adhesive remover to clean any residue on robust surfaces Avoid pulling straight out from the wall to reduce risk of paint lift Specifications Brand T-Rex Product type Clear double sided mounting tape Width 19 mm Length 4.5 m Colour Clear Adhesive Acrylic based Indoor or outdoor Indoor and protected outdoor applications Liner Peel off release film Good to know For best results on painted walls, ensure paint is fully cured Heavier items may need additional strips to spread the load Use continuous strips near the edges of flat panels to reduce shear What is in the pack 1 x roll T-Rex Clear Double Sided Tape 19 mm x 4.5 m FAQs Can I use it in wet areasYes for sealed, smooth surfaces such as glazed tiles and glass. Avoid constant immersion. Will it damage paintIt can if paint is weak or not fully cured. Test first and remove slowly with heat to soften the adhesive. Can it hold shelvesThis tape is ideal for light mounting and trim. Use mechanical fixings for shelves and heavy items.
$22.74 $17.05
Fast, tough and tidy. This bright white duct tape delivers a strong hold for patching, bundling, sealing and quick fixes indoors and outdoors. It tears by hand for easy application and leaves a clean look on light surfaces. Strong hold for everyday repairs and jobsite tasks Weather resistant backing that helps shed moisture UV resistant colour that stays bright in the sun Hand tear across or along the roll for fast use Conforms to rough, uneven and curved surfaces Clean white finish blends with trim, appliances and walls Great for Sealing and patching around the home, site and shed Temporary cable bundling and gear organisation Quick fixes on tools, hoses, tarps and camping gear Labelling and marking on light coloured surfaces Craft, props and event setups where a white finish is preferred Surface Compatibility Adheres to most clean, dry surfaces including metal, plastic, painted timber, vinyl, glass, masonry, cardboard and fabric. Not recommended on freshly painted walls, delicate finishes, porous stone or where residue free removal is essential. How to Use Clean and dry the surface. Remove dust, oil and loose flakes. Unroll and press the tape down firmly as you go to avoid air pockets. For heavy duty holds, wrap or overlap the tape to increase grip. To remove, lift a corner and peel back slowly at a low angle. Pro Tips At cooler temperatures, warm the tape and surface for best tack. For long term outdoor use, apply to smooth, sealed surfaces. Test first on sensitive areas to check finish and removal. Specifications Brand T-Rex Product type Duct tape Colour White Width 48 mm Length 9.1 m Use Indoor and outdoor Finish Matte white What is in the Box 1 x Roll of T-Rex White Duct Tape 48 mm x 9.1 m Frequently Asked Questions Will it hold in the rain?The backing helps resist moisture and the adhesive bonds well to dry, prepared surfaces. Apply to a clean, dry surface for best results. Is it paintable?Many users paint over duct tape for temporary cosmetics. For the best finish, use a suitable primer and test first. Will it leave residue?Like most strong duct tapes, residue can occur, especially after long exposure to heat and sun. Test on sensitive finishes and remove slowly.
$17.05 $14.74
Keep jobs moving with a reliable, multipurpose PVC duct tape built for quick fixes and everyday maintenance. Paint Partner PVC Duct Tape bonds fast, conforms to uneven surfaces, and helps you seal, bundle, repair, and patch with confidence on site or at home. Why you will like it Strong instant hold grips to plastics, metal, timber, cardboard, and painted surfaces. Tear by hand for fast application when you do not have a knife handy. Flexible PVC backing conforms around pipes, ducts, cables, edges, and corners. Good weather resistance suitable for indoor use and light outdoor tasks. Clean removal designed to leave minimal residue when removed within a reasonable time. Low shine finish helps reduce glare on stage, sets, and job sites. Great for Sealing ducting joins and flexible hose connections Temporary patching of tarps, plastic sheeting, and packaging Bundling cables and securing drop sheets Edge protection on work surfaces and tool cases Quick fixes on site, in workshops, sheds, and vehicles Surface compatibility Adheres well to smooth, clean, and dry surfaces including PVC, PE sheeting, aluminium, steel, timber, painted walls, and cardboard. Test first on delicate or freshly painted areas. How to use Clean and dry the surface. Remove dust, oils, and loose paint. Unroll and tear or cut the required length. Press down firmly and smooth from the centre out to remove air pockets. For joints or patches, overlap edges by at least 20 mm. To remove, peel back slowly at a low angle. Remove within a reasonable time for the cleanest results. Tips For extra hold on porous surfaces, apply additional pressure with a roller. Avoid prolonged exposure to strong UV and high heat if a pristine finish is required. Not a substitute for permanent structural repairs or certified electrical insulation. Product details Backing PVC Adhesive Rubber based Finish Low sheen Use Indoor and light outdoor tasks Removal Minimal residue when removed within a reasonable time FAQs Is it waterproofIt resists moisture and splashes for temporary sealing. For long term underwater or high pressure sealing, choose a dedicated waterproof repair product. Can I paint over itMost paints will not adhere well to PVC tape. Remove the tape after painting or mask with a paintable tape. Will it damage surfacesOn most sound surfaces it removes cleanly when taken off in a reasonable time frame. Always test first on delicate, aged, or freshly painted surfaces. Good to know Store in a cool, dry place out of direct sunlight. Apply between 10°C and 35°C for best results.
$4.64 $3.63
Keep jobs moving with a reliable, multipurpose PVC duct tape built for quick fixes and everyday maintenance. Paint Partner PVC Duct Tape bonds fast, conforms to uneven surfaces, and helps you seal, bundle, repair, and patch with confidence on site or at home. Why you will like it Strong instant hold grips to plastics, metal, timber, cardboard, and painted surfaces. Tear by hand for fast application when you do not have a knife handy. Flexible PVC backing conforms around pipes, ducts, cables, edges, and corners. Good weather resistance suitable for indoor use and light outdoor tasks. Clean removal designed to leave minimal residue when removed within a reasonable time. Low shine finish helps reduce glare on stage, sets, and job sites. Great for Sealing ducting joins and flexible hose connections Temporary patching of tarps, plastic sheeting, and packaging Bundling cables and securing drop sheets Edge protection on work surfaces and tool cases Quick fixes on site, in workshops, sheds, and vehicles Surface compatibility Adheres well to smooth, clean, and dry surfaces including PVC, PE sheeting, aluminium, steel, timber, painted walls, and cardboard. Test first on delicate or freshly painted areas. How to use Clean and dry the surface. Remove dust, oils, and loose paint. Unroll and tear or cut the required length. Press down firmly and smooth from the centre out to remove air pockets. For joints or patches, overlap edges by at least 20 mm. To remove, peel back slowly at a low angle. Remove within a reasonable time for the cleanest results. Tips For extra hold on porous surfaces, apply additional pressure with a roller. Avoid prolonged exposure to strong UV and high heat if a pristine finish is required. Not a substitute for permanent structural repairs or certified electrical insulation. Product details Backing PVC Adhesive Rubber based Finish Low sheen Use Indoor and light outdoor tasks Removal Minimal residue when removed within a reasonable time FAQs Is it waterproofIt resists moisture and splashes for temporary sealing. For long term underwater or high pressure sealing, choose a dedicated waterproof repair product. Can I paint over itMost paints will not adhere well to PVC tape. Remove the tape after painting or mask with a paintable tape. Will it damage surfacesOn most sound surfaces it removes cleanly when taken off in a reasonable time frame. Always test first on delicate, aged, or freshly painted surfaces. Good to know Store in a cool, dry place out of direct sunlight. Apply between 10°C and 35°C for best results.
$4.55 $3.63
Keep notes, artwork, bills and reminders up where you can see them without nails or mess. Command Spring Clips grip paper and lightweight items securely, then remove cleanly when you are ready for a change. Ideal for kitchens, study corners, classrooms, rentals and offices. Why you will like it Damage free hanging on most painted walls, tile, metal and glass Holds firmly, then removes cleanly with no sticky residue Simple squeeze to clip, easy lift tab to remove the strip Clean white finish that blends with any space Great for lists, rosters, kids art, mail and reminders What is in the box 8 × Command Spring Clips, White 12 × Command Adhesive Strips Model number: 17089-8ES Recommended uses Pin timetables on pantry doors Display school notes near the entry Hold recipes at eye level while you cook Organise invoices and mail by the desk Where it works Most painted drywall, finished wood, tile, metal, glass Where not to use Wallpaper, brick, rough or textured surfaces Walls painted with non stick or low VOC paints that resist adhesives Wet areas that stay steamy for long periods How to apply Clean the surface with methylated spirits or isopropyl alcohol. Let it dry. Peel the liner marked “wall” and press the strip to the wall for 30 seconds. Peel the other liner and press the clip base to the strip for 30 seconds. Slide the clip onto its base and wait 1 hour before use for best hold. How to remove cleanly Hold the clip gently so it does not spring off. Grip the tab and pull the strip straight down, slowly, keeping it flat against the wall until it releases. Good to know Use a fresh strip if you reposition the clip Do not hang valuable or irreplaceable items Test first on an inconspicuous spot if unsure about the surface Specs Finish White Pack contents 8 clips, 12 adhesive strips Model 17089-8ES Room Kitchen, study, office, classroom Surface type Most smooth, sealed surfaces Tips for best results Apply to clean, dry, cool surfaces Wait the full hour before clipping items Replace strips if the clip is moved to a new spot
$45.00
Replacement adhesive strips to reuse your existing Command hooks and hangers. Fresh adhesive for reliable hold Easy to apply and remove cleanly Sized to fit matching hooks Examples of use: Refresh worn strips on bathroom hooks Swap seasonal decor without new hardware Rehang key rails and caddies
$8.38
Picture hanger engineered for wire-back or sawtooth frames with stable support. Quick stick-on install Clean removal with no wall damage Keeps frames level Examples of use: Hang framed art and certificates Display mirrors within weight rating Mount signage in halls
$11.21
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$7.78
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$26.76
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$19.47
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$17.65
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$16.33
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$11.54
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$7.28
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$20.99
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$12.54
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$17.64
Versatile wire-shaped hooks that fit odd items and handles. Slim profile for tight spots Damage-free removal Reusable with refill strips Examples of use: Hang cleaning brushes Store headphones and lanyards Hold small planters by a window
$7.55
Adhesive key rail with multiple hooks to organise everyday carry items. Damage-free install Stable hold for keys and lanyards Neat, minimalist look Examples of use: Park car and house keys by the door Hang dog leads and caps Keep swipe cards in the office
$24.53
Replacement adhesive strips to reuse your existing Command hooks and hangers. Fresh adhesive for reliable hold Easy to apply and remove cleanly Sized to fit matching hooks Examples of use: Refresh worn strips on bathroom hooks Swap seasonal decor without new hardware Rehang key rails and caddies
$5.34
Round adhesive clips to guide and tame charging or appliance cords. Keeps cables in place Damage-free removal Blends with modern setups Examples of use: Route a phone charger behind a nightstand Secure a lamp cord to a skirting board Organise USB leads near a workstation
$7.13
Bathroom caddy accessory that mounts without drilling for tidy storage. Water-resistant adhesive Rust-free design Removes cleanly from tiles and glass Examples of use: Hold soap and sponges at the sink Keep shower gels within reach Organise shaving accessories
$32.67
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$9.05
Replacement adhesive strips to reuse your existing Command hooks and hangers. Fresh adhesive for reliable hold Easy to apply and remove cleanly Sized to fit matching hooks Examples of use: Refresh worn strips on bathroom hooks Swap seasonal decor without new hardware Rehang key rails and caddies
$10.40
Clear mini hooks sized for kitchen tools and lightweight accessories. Food-area friendly surfaces Removes cleanly Compact, clear design Examples of use: Hang measuring spoons by the stove Hold tea towels or oven mitts Store small gadgets on a splashback
$6.95
You have seen 336 out of 720 products
Find products tagged for use on wood. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on wood surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
