Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.57
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.57
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 3]](http://gluesaustralia.com.au/cdn/shop/files/638060661598_a9209f0c-7031-48ec-be4f-9fb1e87b6730.jpg?v=1754712828&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$26.54
Selleys Liquid Nails Heavy Duty is a high-strength construction adhesive built for demanding structural bonding, supplied here as a value three-pack of 350g cartridges. It develops around twice the strength of Liquid Nails Original in less than half the time, so heavy or bulky materials can be fixed and left to hold sooner.About the formulaA solvent-based synthetic rubber resin adhesive with a thick, non-sag consistency. It grips on vertical and overhead surfaces without slumping or stringing, extrudes easily even in cold winter conditions, and resists water and weather for both interior and exterior work.Where to use itIndoors: sheet flooring to joists, wallboard and panelling to timber or metal frames, cork or timber to plaster and fibre cement, and metal or aluminium trims to floors and walls.Outdoors: bonding timber, fibre cement sheeting, stone tiles and masonry where a weather-resistant structural bond is needed.Suitable materials include timber, MDF, particleboard, plasterboard, masonry, concrete, metals, rubber, glass, and tiles and ceramics. Pre-test plastics for compatibility.How to use itMake sure surfaces are clean, dry and free of oil, grease and dust. Cut the cartridge tip, fit the nozzle and trim to roughly a 5mm opening. For a wet bond, run a bead along studs, joists or battens (or every 40cm on broad flat surfaces), position within 15 minutes and support with nails, screws or clamps for at least 8 hours. For faster grab, use the contact method: apply to one surface, press together and pull apart, wait 2 to 4 minutes, then join firmly within 10 minutes.Important notesBond strength keeps building over 2 to 3 days, with full cure taking up to 7 days. Curing relies on solvent evaporation, so cold temperatures, thick joints, wide bonded areas and non-porous surfaces such as metals and dense timbers all slow it down. Not intended for continuous water immersion.Specifications Brand Selleys Product Liquid Nails Heavy Duty Construction Adhesive Pack 3 x 350g cartridges Colour Brown Base Solvent-based synthetic rubber resin Application Cartridge, via caulking gun Repositionable Up to about 15 minutes (wet bond) Initial set About 8 hours Full cure Up to 7 days Use Interior and exterior SafetyClassified as a highly flammable liquid and vapour (contains methyl acetate, acetone and light naphtha). May cause skin irritation and serious eye irritation and may cause drowsiness or dizziness. Use only outdoors or in a well-ventilated area and keep away from heat, sparks and open flame. Wear protective gloves and eye protection. On skin contact, remove affected clothing and rinse with water; for eye contact, rinse continuously for at least 15 minutes; if inhaled, move to fresh air; seek medical advice if irritation persists. Store upright in a cool, dry, well-ventilated place out of direct sunlight and keep the cartridge tightly capped. Always refer to the manufacturer Safety Data Sheet before use.
$27.70
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
The Dunlop Mixing Paddle is a cost-effective drill-driven paddle that takes the hard work out of blending cement-based products to a smooth, lump-free consistency. Its blade profile is shaped to pull dry powder up from the sides and bottom of the bucket, so every batch is fully combined and ready to apply, with no wasted material left clinging to the pail.Where to use itAttach it to a suitable mixing drill whenever you are preparing mortars, tile adhesives, floor levellers, render, plaster or screeds. It is the natural partner for bagged Dunlop products across tiling, rendering and floor-levelling jobs, and works just as well for small DIY batches as it does for repeated trade mixing on site, indoors or outdoors.Features Mixes mortars, tile adhesives, floor levellers, render, plaster and screeds Blade design lifts dry powder from the bucket sides and base for a complete mix Helps achieve a consistent, lump-free result every batch Cost-effective trade-quality paddle Fits standard mixing drills CareImmediately after mixing, spin the paddle in a bucket of clean water to flush off wet product, then wipe it down before anything sets on the shaft or blades. Dry the paddle before storage to prevent corrosion and check the shaft is straight before each use.
$28.80
Dunlop Ardit Construction Grout in the full-size 20kg bag is a high-strength, multipurpose construction grout that mixes to either a non-slump paste or a flowable consistency to suit a wide range of projects. Its extended working time allows extra minutes for accurate positioning before set, and the non-shrink formulation locks components firmly in place. The grout achieves approximately 45MPa after 7 days and around 65MPa at 28 days, and carries a 10 year guarantee, making it a dependable choice for structural packing and grouting work.Where to use itDesigned for indoor and outdoor use in general construction grouting and machine grouting applications: grouting under machine bases, baseplates and stanchions, filling voids, pockets and core holes in concrete, bedding structural members, and anchoring bolts, rails and fixings into concrete and masonry. Application thickness ranges from 5mm to 100mm.How to useEnsure surfaces are structurally sound, clean and free of dust, oil and laitance, and pre-dampen porous substrates. Mix with clean water to the consistency required — a stiff non-slump mix for hand packing and trowelling, or a flowable mix for pouring into formwork and confined spaces. Place within the working time and compact well to eliminate air voids. A 20kg bag yields approximately 11.2L as a non-slump mix or 12.0L as a flowable mix.Important notesKeep within the 5-100mm application range. Avoid adding excess water, which lowers strength and increases shrinkage risk. Low temperatures slow strength development; protect fresh grout from rapid drying in hot or windy conditions.Specifications Size 20kg bag Colour Grey Yield 11.2L per 20kg (non-slump), 12.0L per 20kg (flowable) Compressive strength Approx. 45MPa (7 days), 65MPa (28 days) Application thickness 5-100mm SafetyCement-based product — wet grout is alkaline and may cause skin and eye irritation. Wear protective gloves, eye protection and a P2 dust mask when mixing. Avoid breathing dust. Consult the Safety Data Sheet before use and store in a dry place out of reach of children.
$42.23
Dunlop General Purpose Construction Grout is an economical, high-strength cementitious grout that can be mixed to a dry pack, plastic or flowable state, giving one bag remarkable versatility across construction and repair tasks. The shrinkage-compensated formulation holds its volume as it cures, and strength development is impressive for a general purpose product — approximately 70MPa at 7 days and up to 85MPa at 28 days when mixed as a dry pack with 12% water.Where to use itSuited to indoor and outdoor projects wherever a dependable, high-strength grout is needed: packing under baseplates and machinery, filling voids, holes and pockets in concrete, bedding posts and bollards, grouting anchor bolts and starter bars, and general making-good around concrete and masonry. Application thickness ranges from 10mm up to 100mm.How to useStart with a clean, sound substrate free of dust, oil and loose particles, and dampen absorbent surfaces before grouting. Add clean water to achieve the consistency the job requires — dry pack for ramming into confined spaces, plastic for trowel placement, or flowable for pouring. Compact or rod the grout to remove entrapped air and finish with a steel trowel. A 20kg bag yields approximately 9.5L as dry pack, 10.3L at plastic consistency or 10.9L as a flowable mix. Varying the water ratio changes both workability and final strength.Important notesHigher water contents make placement easier but reduce ultimate strength — use the minimum water needed for workability. Maintain the 10-100mm thickness range and protect fresh grout from freezing and from rapid drying.Specifications Size 20kg bag Colour Grey Yield 9.5-10.9L per 20kg depending on consistency Compressive strength Approx. 70MPa (7 days), 85MPa (28 days) as dry pack Application thickness 10-100mm SafetyContains portland cement — wet product is alkaline and can burn skin and eyes on prolonged contact. Wear gloves, safety glasses and a dust mask when mixing, and avoid breathing dust. Read the Safety Data Sheet before use.
$26.30
Dunlop Ardit Construction Grout is a high-strength, cement-based grout that can be mixed to either a stiff, paste-like consistency or a free-flowing pour, making it a genuine all-rounder for construction and repair work. Formulated with Ardit Technology and an extended working time, it gives you more room to position components accurately before the mix begins to set. This non-shrink formulation reaches approximately 45MPa after 7 days and around 65MPa at 28 days, and it is backed by a 10 year guarantee. The handy 5kg bag suits smaller jobs and repairs without the waste of a full-size bag.Where to use itSuitable for indoor and outdoor projects wherever a high-strength, non-shrink grout is required — general construction grouting, machine and equipment base grouting, filling voids and pockets in concrete, bedding and packing under plates, and anchoring bolts, rails and posts. It performs over concrete and masonry substrates at application thicknesses from 5mm up to 100mm.How to usePrepare a sound, clean substrate free of dust, oil and loose material, and pre-dampen absorbent surfaces. Mix the powder with clean water to the consistency the job calls for — non-slump paste for vertical packing or a flowable mix for pouring into forms and voids. Place the grout within its working time, compacting or rodding to remove air pockets, then finish with a trowel. As a guide, a 20kg quantity yields roughly 11.2L as a non-slump mix or 12.0L as a flowable mix, so expect around a quarter of that from this 5kg bag.Important notesApply between 5mm and 100mm thickness. Do not over-water the mix, as excess water reduces final strength. Cold or damp conditions extend curing times; hot, windy conditions shorten working time.Specifications Size 5kg bag Colour Grey Yield Approx. 2.8-3.0L per 5kg depending on consistency Compressive strength Approx. 45MPa (7 days), 65MPa (28 days) Application thickness 5-100mm SafetyContains cement — the wet mix is alkaline and can irritate skin and eyes. Wear gloves, safety glasses and a dust mask when handling the dry powder, work in a ventilated area and wash hands after use. Refer to the Safety Data Sheet before use and keep out of reach of children.
$23.73
Dunlop Artificial Grass Adhesive is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia), purpose-made for laying artificial grass, outdoor carpet and marine carpet. With excellent water and heat resistance and a bond that stands up to sun, rain and foot traffic, it is the reliable way to keep synthetic turf flat and secure – and it is backed by a 10 year guarantee. This handy 1 litre can is ideal for smaller lawns, edges, joins and repair work.Where to use itDesigned primarily for outdoor projects such as synthetic lawns, pool surrounds, balconies, courtyards and boat decks, and equally suitable for indoor applications like covered patios and utility areas. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to useEnsure the surface is clean, dry and free of dust, oil and loose material. Spread the adhesive evenly with a suitable notched spreader or trowel at approximately 3m² per litre, then lay the grass or carpet into the wet adhesive, smoothing outwards to remove air pockets. Weight or roll the surface while the adhesive develops strength and avoid heavy traffic until fully cured.Important notesDo not apply in extremely hot or cold conditions – work between 10°C and 30°C – and never apply when dew or rain is imminent, as moisture can affect bond development before cure.Specifications Size 1 litre can Colour Green Coverage Approx. 3m² per litre Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: use only in well-ventilated areas, keep away from heat, sparks and open flames, and avoid breathing vapours. Wear gloves and eye protection, replace the lid when not in use and keep out of reach of children. Refer to the safety data sheet before use.
$35.99
Dunlop Artificial Grass Adhesive in the value 4 litre can is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia) for laying artificial grass, outdoor carpet and marine carpet across larger areas. Formulated with excellent water and heat resistance, it keeps synthetic turf and outdoor floor coverings firmly bonded through harsh Australian conditions, and is backed by a 10 year guarantee. At roughly 3m² per litre, one 4L can covers around 12m² – ideal for full lawns, entertaining areas and commercial installs.Where to use itBuilt for outdoor projects – synthetic lawns, pool surrounds, balconies, rooftops, courtyards and marine decks – and also suitable for indoor areas such as covered patios. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to usePrepare a clean, dry, dust-free surface. Spread the adhesive evenly using a suitable notched spreader or trowel, working in sections you can cover while the adhesive is wet. Lay the grass or carpet into the adhesive, smooth outwards to expel trapped air, then roll or weight the surface. Keep traffic off until the adhesive has fully cured.Important notesDo not use in extremely hot or cold conditions – apply between 10°C and 30°C – and do not apply when dew or rain is expected before the adhesive has set. Ensure joins are well supported and seams glued continuously for a lasting result.Specifications Size 4 litre can Colour Green Coverage Approx. 3m² per litre (about 12m² per can) Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: ensure good ventilation, keep away from ignition sources and avoid inhaling vapours. Wear protective gloves and eye protection, reseal the can after use and store away from children. Consult the safety data sheet before use.
$97.56
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Ardit Crack Filler is a high strength, two-part hybrid polyurethane that repairs cracks and spalls in concrete almost instantly. With a viscosity similar to water, it flows deep into cracks that pastes and mortars can't reach, then cures harder than the surrounding concrete within an hour. Driveable repairs are possible in as little as 20 minutes, making it a genuine problem-solver for busy floors and driveways.Where to use itSuitable for indoor and outdoor concrete - garage floors, driveways, paths, warehouse slabs and patios. Because the two parts mix automatically through the nozzle, it is equally at home in a professional toolkit or a weekend repair kit.How to useClean the crack thoroughly, removing dust, loose material and any moisture. Load the 254ml dual cartridge into a suitable applicator gun, attach the self-mixing nozzle and dispense directly into the crack until full. For wider spalls and larger repairs, blend in clean, dry bagged aggregate to bulk the fill. The repair sets stronger than concrete in about 1 hour and takes vehicle traffic after roughly 20 minutes.Important notesNew concrete must be fully cured - at least 28 days old - before application. The water-thin consistency is designed for penetrating cracks, so dam or tape the ends of through-cracks where needed. Used nozzles cannot be reused once the product sets.Specifications Size 254ml dual cartridge Coverage Depends on crack width and depth Thickness Flows to full crack depth; add aggregate for large voids Substrates Concrete Set time Drive on after 20 minutes; full strength in 1 hour SafetyReactive polyurethane resins can irritate skin and airways before curing. Wear nitrile gloves and safety glasses, work in a well-ventilated area, avoid skin contact with uncured product and keep it away from children. Dispose of cartridges according to local regulations.
$67.48
Dunlop Builder's Bond is a high strength, multipurpose, rapid-cure epoxy bonding and repair system that joins almost any building material to almost any other. Dispensed through a self-mixing nozzle from a convenient 254ml dual cartridge, its non-sag formula holds firm on walls and even overhead, and cures stronger than concrete in about 2 hours.Where to use itSuitable for indoor and outdoor use across floor, wall and overhead repairs. Typical jobs include bonding concrete, masonry, stone, metal and timber components, rebuilding broken edges and corners, anchoring fixtures, and general structural gap filling where a fast, very strong bond is required.How to useEnsure both surfaces are clean, dry and free of dust, grease and loose material. Load the cartridge into an applicator gun, fit the self-mixing nozzle and dispense the evenly mixed epoxy directly onto the repair or bond line. Shape and tool it before it stiffens. Once cured, Builder's Bond can be shaped, sanded, drilled and painted, so repairs can be blended invisibly into the surrounding surface.Important notesNew concrete must be fully cured - a minimum of 28 days old - before bonding. The non-sag consistency suits vertical and overhead work but is not a pourable grout. Start a fresh nozzle for each session, as mixed product hardens inside the nozzle.Specifications Size 254ml dual cartridge Coverage Depends on bead size and gap width Substrates Concrete, masonry, stone, metal, timber and most building materials Set time Stronger than concrete in 2 hours Finish Sandable, drillable and paintable once cured SafetyUncured epoxy resins and hardeners can cause skin irritation and sensitisation. Wear nitrile gloves and eye protection, ventilate the work area, avoid skin contact and wash immediately if contact occurs. Keep cartridges sealed and out of reach of children.
$61.79
For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal Metalox Metal Repair Epoxy Kit 10 x 25ml Bi-Syringes Loxeal Metalox is a solvent-free, fast-curing, metal-filled two-part epoxy engineered for repairing and bonding metal components. This trade pack contains 10 x 25ml bi-syringes, each supplied with mixing nozzles, so every job starts with fresh, accurately proportioned adhesive. Its thixotropic (non-sag) paste works as an adhesive filler – rebuilding metal castings, pipework and flanges – and once cured it can be machined, sanded and painted, typically within a few hours of application. Why choose Loxeal Metalox? Trade pack of 10 x 25ml bi-syringes with mixers – fresh 1:1 dispensing on every repair Fast cure – handling strength in around 15 minutes, sandable in about 5 hours at room temperature Strong on steel – lap shear strength of 21 N/mm² on grit-blasted mild steel Machinable, sandable and paintable after polymerisation, even for outdoor repairs Non-sag thixotropic paste stays put on vertical and overhead surfaces Excellent resistance to water and many chemical agents Heat cure option: 1 hour at +60°C speeds cure and boosts final strength Typical applications Repairing metal castings, pipework and flanges Automotive body repair and panel filling Bonding metal substrates, plus concrete, wood and other rigid materials Maintenance and plant repairs where downtime must be kept short How to use Scratch or abrade the surface, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the bi-syringe and discard the first 3–5 cm of extruded product. Apply the mixed adhesive directly to the repair area; work at temperatures above +15°C. Assemble or shape immediately and leave undisturbed until cured. Once cured (sandable after about 5 hours at +25°C), machine, sand or paint as required. Cure times Pot life: approximately 5 minutes at +25°C Handling strength: approximately 15 minutes Sandable: about 5 hours at +25°C (90% of final hardness) Accelerated cure: 1 hour at +60°C for full resistance sooner Specifications Chemistry Two-part epoxy (resin / amine hardener), metal-filled Colour Part A metallic grey / Part B black Mixing ratio 1:1 by volume Pot life (+25°C) Approx. 5 minutes Handling strength Approx. 15 minutes Lap shear strength (ISO 4587) 21 N/mm² (grit-blasted mild steel); 18 N/mm² (stainless steel) Compression strength (ASTM D695) 60 N/mm² Hardness (ISO 868) Shore D 65 Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Shelf life 24 months unopened at +5°C to +25°C Important notes Apply at temperatures above +15°C; higher temperatures and large mixed quantities reduce pot life Avoid mixing excess product – the curing reaction generates heat Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Wear suitable gloves, avoid skin and eye contact, and work in a well-ventilated area. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$385.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$60.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$57.95
Krud Kutter Original Cleaner and Degreaser 946ml (Ready to Use Trigger Spray) Krud Kutter Original is a water-based cleaner, degreaser and stain remover that handles tough soils across a wide range of surfaces from a single bottle. Packed in a 946ml trigger pack, it sprays on straight from the bottle for everyday messes and can be used at full strength on the most stubborn grease and grime. It is biodegradable, low in odour and free from bleach, ammonia and harsh solvents, which makes it a practical choice for kitchens, garages, workshops and outdoor areas alike. Formula overview The formula combines a water base with a gentle surfactant system, an alkaline builder and a chelating agent that together lift fats, oils, road film and ground-in dirt. Because it relies on water-based chemistry rather than petroleum solvents, it rinses away cleanly, leaves no oily residue and is safe on most washable indoor, automotive and marine surfaces. It is colour fast and fabric safe on most materials, though a spot test is always sensible before a full clean. Where to use it Indoors Kitchen benches, splashbacks, range hoods, oven exteriors and BBQ grills Tiles and grout, sinks, tubs and shower screens with soap scum build up Painted walls, skirting and doors (test first and dilute for light marks) Lifting food and drink stains, marker, crayon, scuff marks and grease spots Outdoors Concrete paths, driveways and garage floors with oil and grease staining Outdoor furniture, fences and rendered or masonry surfaces Tools, machinery and engine parts (use on a cold, dry engine) Removing tree sap, bird droppings, brake dust and general weather grime How to use Always test on a small, hidden area first to check surface compatibility. For everyday cleaning, spray directly onto the surface and let it sit briefly. Wipe away with a clean, damp cloth or sponge. For heavy grease, oil or dried paint, apply at full strength, leave for a few minutes, then agitate with a brush or pad before wiping with a wet rag. For lighter cleaning over larger areas, the concentrate can be diluted with water. Rinse food contact surfaces with clean water after cleaning. Important notes Do not use on varnished surfaces or on leather. The formula is alkaline, so avoid prolonged contact with bare aluminium and other sensitive metals, and rinse and dry after use. Always test painted, delicate or porous surfaces in an inconspicuous spot before a full clean. Do not mix with other cleaning chemicals. Keep out of reach of children and pets. Specifications Brand Krud Kutter Product Original Cleaner, Degreaser and Stain Remover Format Ready to use trigger spray (concentrate, dilutable) Size 946 ml Base Water-based, biodegradable Use Interior and exterior Suitable surfaces Sealed hard surfaces, tiles and grout, glass, most plastics, metal, concrete and masonry, automotive and marine surfaces Not suitable for Varnished surfaces and leather Safety Keep out of reach of children. Avoid contact with eyes. If product enters the eyes, rinse with plenty of water and seek medical advice if irritation continues. Wear gloves if you have sensitive skin, and wash hands after use. Use in a well ventilated area and avoid breathing in the spray mist. Store upright in the closed bottle, away from extreme heat. Refer to the manufacturer Safety Data Sheet for full handling, first aid and disposal guidance. Glues Australia ships Australia wide. If you are not sure whether Krud Kutter is right for your surface, contact our team and we will help you pick the right cleaner for the job.
$20.05
Tricleanium All Purpose Cleaner RTU is the ready-to-use, trigger-spray version of the cult Australian cleaner that tradespeople and professional cleaners have relied on for generations. It works straight from the 750 mL bottle with no mixing or dilution, making it ideal for fast spot cleaning and surface preparation around the home, workshop and job site.Built on a formula of 100% alkaline salts, it is non-caustic, non-corrosive and anti-bacterial, yet powerful enough to cut through grease, baked-on grime, mould, smoke stains, finger marks and general dirt on most washable surfaces, including painted walls, concrete, tiles, laminate, plastics, stainless steel and glass.Where to use itIndoors: walls and ceilings, benchtops, tiles and slate, stovetops, ovens and oven trays, frypans, rangehoods and exhaust fan covers, splashbacks, sinks, baths and showers, glass and windows, fridges, cupboards and shelves, washing machines and home-brewing equipment. It is also excellent for preparing walls before painting or wallpapering, and for softening old wallpaper glue.Outdoors: weatherboards, external timber and brickwork, BBQs and hotplates, awnings and external blinds, tarpaulins and tonneau covers, greasy engine parts, and grease or oil stains on driveways and concrete.How to useSpray directly onto the surface and allow a few moments to penetrate, without letting it dry. Wipe with a soft cloth, then rinse with fresh water so no residue is left behind. When cleaning glass or windows, rinse immediately with fresh water to prevent clouding. Rinse all cleaned surfaces with fresh water afterwards.Important notes Not recommended for brass or aluminium-plated surfaces. Keep away from carpet and any surface that is not colourfast. Always test an inconspicuous area first if you are unsure how a surface will react. Specifications Brand Tricleanium Product type All-purpose cleaner (ready to use) Volume 750 mL Format Trigger spray bottle Composition 100% alkaline salts; contains trisodium phosphate (1 to 3%) Properties Non-caustic, non-corrosive, anti-bacterial, strongly alkaline (high pH) Dilution Not required (ready to use) Suitable surfaces Painted surfaces, concrete, tile, laminate, plastic, stainless steel, glass and most washable surfaces Not suitable for Brass, aluminium-plated surfaces, carpet, non-colourfast surfaces Country of origin Australia SafetyCauses skin irritation and serious eye irritation, and may cause respiratory irritation. Wear protective gloves and eye protection, use in a well-ventilated area, and keep out of reach of children. Harmful to aquatic life due to its high pH, so avoid release to the environment. Read the manufacturer's Safety Data Sheet before use.
$13.84
Glitz Sugar Soap for Floors Heavy Duty Cleaner Power through ground-in dirt, grease, and everyday grime with Glitz Sugar Soap for Floors. This heavy duty formula lifts stubborn residues and leaves floors fresh, streak free, and ready for living. Ideal for high traffic areas in homes, workshops, and commercial spaces. Why you will love it Heavy duty clean that cuts through grease, scuff marks, and sticky spills Low foam for a streak free finish on most sealed floors Fast acting formula reduces scrubbing time Residue free so finishes and sealers look their best Fresh, low odour for comfortable indoor use Best for these surfaces Use on most sealed and washable floors, including: Ceramic and porcelain tiles Vinyl and hybrid floors Laminate and sealed timber Sealed concrete and epoxy coated floors Do not use on unsealed timber, unsealed cork, natural stone that is unsealed, or waxed finishes. Always test in a small inconspicuous area first. How to use Sweep or vacuum to remove dust and grit. Dilute in warm water: General cleaning: 1 capful per 5 L bucket Heavy duty cleaning: 2 to 3 capfuls per 5 L bucket Apply with a mop or sponge. Work in sections. For stubborn spots, apply a little solution directly, wait 2 to 3 minutes, then gently agitate. Rinse mop frequently in clean water. Allow floor to dry before walking. Pro tips Change the bucket water when it turns cloudy to avoid streaks. Use heavy duty dilution before repainting or resealing floors to remove grease and prep the surface. For gloss finishes, wring the mop well to prevent pooling. Product details Brand Glitz Product type Sugar soap floor cleaner Format Liquid concentrate Appearance Clear to light solution, low foam Suitable surfaces Most sealed hard floors Clean up Rinse tools and mops in clean water Storage Keep tightly closed in a cool, dry place Safety Wear gloves if you have sensitive skin. Avoid contact with eyes. If splashed, rinse with water. Keep out of reach of children and pets. FAQs Do I need to rinse after cleaning Rinsing is generally not required on sealed floors when diluted as directed. If using heavy duty strength, a light rinse with clean water can help achieve a streak free finish. Can I use it in a spray mop Yes. Pre dilute following the general cleaning ratio and avoid over wetting the floor. Good to know Compatible with most microfiber and cotton mops Great prep step before resealing or repainting floors Helps remove oily residues that make floors feel slippery
$5.27 $4.94
Glitz Degreaser Heavy Duty Kitchen Cleaner 500ml Cut through baked-on grease and everyday kitchen grime fast. Glitz Degreaser Heavy Duty Kitchen Cleaner is a ready to use spray designed for cooktops, rangehoods, splashbacks, benches, and more. It lifts fats, oils, and food residue so you get a clean, streak free finish with less scrubbing. Why you will love it Heavy duty action - breaks down stubborn grease, oils, and burnt on residue Ready to use - no mixing required, just spray, wait, and wipe Streak free finish - leaves hard kitchen surfaces looking fresh Versatile - ideal for stainless steel rangehood exteriors, ceramic and glass cooktops, tiled splashbacks, benches, cupboard doors, and BBQ exteriors Fast results - reduces scrubbing time on tough build up Best for these jobs Cutting grease on cooktops and around burners De gunking rangehood filters and exteriors Cleaning oven doors and surrounding panels Removing oily fingerprints on cupboard doors and fridges Wiping down tiled splashbacks and benchtops Directions Switch off appliances and allow surfaces to cool. Shake bottle gently. Turn nozzle to spray. Spray directly onto the soiled area from 15 to 20 cm. Allow 2 to 3 minutes contact time on heavy build up. Do not let dry on the surface. Wipe with a damp cloth or non scratch sponge. Rinse food contact surfaces with clean water and dry with a lint free cloth. Good to know Always test on an inconspicuous area first. Not recommended for unsealed or porous stone such as marble and limestone, unsealed timber, raw aluminium, brass, copper, or varnished surfaces. For painted surfaces, dilute on a cloth first and test. Do not use on hot surfaces. Avoid prolonged contact with stainless steel. Rinse and dry after cleaning. Do not mix with other cleaners or chemicals. Specifications Brand Glitz Product type Heavy duty kitchen degreaser Format Ready to use spray Size 500 ml Suitable surfaces Stainless steel exteriors, ceramic and glass cooktops, tiles, laminates, enamel, sealed stone, and most non porous hard surfaces Safety Wear gloves if you have sensitive skin. Use in a well ventilated area. Avoid breathing spray. Keep out of reach of children and pets. If product gets in eyes rinse with water for several minutes. If irritation persists seek medical advice. Frequently asked questions Can I use this on a hot plate or warm oven No. Always allow surfaces to cool before cleaning. Is it safe on food contact areas Yes, but after cleaning you must rinse the surface with clean water and dry. Will it remove baked on carbon inside an oven It helps on light to moderate build up. For heavy carbon you may need a dedicated oven cleaner. What is in the box 1 x Glitz Degreaser Heavy Duty Kitchen Cleaner 500ml spray bottle Glues Australia ships fast Australia wide. Questions about surface compatibility or bulk orders Contact our team and we will help you choose the right cleaner for the job.
$7.93 $6.33
Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Blast away built up grime, dirt, and weather stains across large outdoor areas with this powerful concentrate. Designed for Aussie backyards, it cuts through tough mess on concrete, pavers, brick, tiles, and timber or composite decks so outdoor spaces look fresh and inviting again. Why you will love it Heavy duty clean that tackles road film, mildew stains, leaf tannins, and greasy marks. Concentrated value so one bottle makes multiple buckets of ready to use solution. Fast results with minimal scrubbing on most surfaces. Versatile for driveways, decks, paths, patios, and outdoor walls. Hose or pressure washer friendly for quick coverage on big jobs. Ideal surfaces Concrete driveways and garage floors Pavers, brick, stone, and outdoor tiles Timber decks and composite decking Rendered walls and fencing Outdoor furniture settings made of hard materials Dilution guide Job type Mix ratio Where to use Heavy build up 1 part cleaner to 4 parts water Oil spots, mildew stains, leaf marks on concrete and pavers General cleaning 1 part cleaner to 10 parts water Routine driveway and deck washes Maintenance 1 part cleaner to 20 parts water Frequent quick cleans and large areas Coverage: A 5L concentrate can make many litres of solution and clean a large area depending on dilution, surface porosity, and soil level. How to use Sweep the area to remove loose debris. Mix to the required ratio in a bucket or pressure washer reservoir. Wet the surface, then apply generously with a garden sprayer, watering can, mop, or pressure washer. Allow 3 to 5 minutes contact time. Do not let the solution dry on the surface. Agitate stubborn spots with a stiff outdoor broom or deck brush. Rinse thoroughly with a hose or pressure washer, pushing residue to drainage. Tips for best results Test on a small hidden patch first to confirm surface compatibility and desired result. Work in the shade on cool surfaces for even cleaning. On timber decks, scrub along the grain and rinse well. Repeat a light application rather than over concentrate for delicate areas. Important information Not recommended for raw or polished natural stone that is sensitive to cleaners. Always patch test first. Avoid use on freshly sealed surfaces. Check sealer instructions before cleaning. Keep runoff away from ponds and delicate plants. Pre wet adjacent garden beds and rinse after cleaning. Safety Wear gloves and eye protection during mixing and application. Ensure good ventilation if using in semi enclosed areas. Store upright in a cool dry place out of reach of children and pets. Specifications Size 5L concentrate Form Liquid cleaner Application Bucket, sprayer, or pressure washer Suitable areas Driveways, decks, patios, paths, outdoor walls What is in the box 1 x Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Frequently asked Will it remove oil stains Heavy oil may require a second application and some scrubbing. For long standing or deep oil, use a degreaser first, then follow with this cleaner for an even finish. Can I use it with a pressure washer Yes. Mix in the detergent tank as per the dilution guide, apply from the bottom up, allow dwell time, then rinse from the top down. Is it safe for sealed decks Patch test first and follow the sealer brand care instructions. Rinse well after cleaning. Good to pair with Outdoor deck brush or stiff broom for agitation Garden sprayer or pressure washer for fast coverage Protective gloves and safety glasses for safe handling
$27.15 $20.89
Bear PVC Duct Tape is a tough, reliable, all purpose tape that delivers a strong hold and a clean finish for quick fixes. Ideal for sealing, bundling, patching, and general repairs at home, on site, and in the workshop. Its PVC backing resists moisture and abrasion, while the high tack adhesive bonds to a wide range of surfaces for dependable results. Why you will love it Fast grab for instant hold on contact Durable PVC backing resists scuffs, tears, and everyday wear Moisture resistant for confident indoor and short term outdoor use Conformable backing wraps neatly around pipes, ducts, and irregular shapes Easy to tear by hand for quick application without tools Low residue when removed from most clean surfaces Great for Sealing HVAC duct joins and flexible ducting Temporary patching of plastic sheeting, tarps, and covers Bundling cables, mats, and lightweight components Edge protection on cartons and packing jobs Quick fixes on site and around the home Works on Metal, plastic, vinyl, painted surfaces, cardboard, glass, masonry, timber, and more. For best results, surfaces should be clean, dry, and free of dust or oils. How to use Prepare the surface by cleaning off dust, grease, and moisture. Measure and tear the required length. Scissors are optional. Apply the tape with firm pressure, smoothing from the center outward to remove air pockets. Reinforce high stress areas with overlapping strips as needed. Pro tips Apply at room temperature for the best initial tack. On porous or rough surfaces, use extra pressure or a primer for maximum bond. For long term outdoor exposure, consider overcoating edges to limit water ingress. Typical specifications Backing PVC Adhesive Rubber based Total thickness Approx. 0.16 to 0.20 mm Temperature range Approx. −10 °C to +60 °C Finish Matte PVC Common sizes 48 mm width, 30 m length and other widths as available Colour Silver or Black depending on variant Values above are typical for PVC duct tapes and may vary by batch and width. FAQs Can I use it outdoorsYes for short term jobs. For permanent outdoor sealing, select a tape rated for UV and long term weather exposure. Will it remove cleanlyOn smooth, sealed surfaces it often removes with minimal residue. Always test on an inconspicuous area first. Is it suitable for high heatPVC duct tape is best within the stated temperature range. For sustained high temperature applications, choose a foil or specialty HVAC tape. Why buy from Glues Australia Trusted Australian supplier with fast dispatch Helpful support if you need sizing or product advice
$12.68 $9.27
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$57.40 $40.04
Get a clean, hardware free look with T-Rex Clear Double Sided Tape. This high performance clear mounting tape creates a strong, permanent bond for photos, hooks, cable clips, house numbers, trims, and light decor. It is ideal when you want the hold without the hardware and a finish that stays virtually invisible on glass, tiles, metal, and painted walls. Why you will love it Crystal clear finish that helps hide the fix for a neat result Strong permanent bond for everyday mounting and craft projects Moisture and UV resistant construction for long lasting performance Instant stick with pressure activation, no curing time required No tools needed, peel and stick application Great for Mounting signage, house numbers, and name plates Securing cable clips and small hooks Fixing splashback trim and edging Crafts, scrapbooking, and photo boards Temporary holding during light assembly Works on Glass and mirrors Glazed tiles and ceramics Metal, aluminium, and stainless steel Finished timber and laminate Painted walls that are sound, clean, and fully cured Most rigid plastics except low surface energy plastics Note: Not recommended for wallpaper, delicate or dusty surfaces, or low surface energy plastics such as PE, PP, and PTFE. Always test on a small area first. How to use Prepare the surface. Clean with isopropyl alcohol and let dry. Remove dust, grease, and loose paint. Apply tape. Cut to length. Apply tape to the lightest item first. Press firmly along the whole strip. Peel liner. Remove the protective liner without touching the adhesive. Mount. Position carefully. Press firmly for 30 to 60 seconds to activate the bond. Maximum strength develops with time under steady pressure. Removal tips Warm gently and peel back slowly at a low angle Use adhesive remover to clean any residue on robust surfaces Avoid pulling straight out from the wall to reduce risk of paint lift Specifications Brand T-Rex Product type Clear double sided mounting tape Width 19 mm Length 4.5 m Colour Clear Adhesive Acrylic based Indoor or outdoor Indoor and protected outdoor applications Liner Peel off release film Good to know For best results on painted walls, ensure paint is fully cured Heavier items may need additional strips to spread the load Use continuous strips near the edges of flat panels to reduce shear What is in the pack 1 x roll T-Rex Clear Double Sided Tape 19 mm x 4.5 m FAQs Can I use it in wet areasYes for sealed, smooth surfaces such as glazed tiles and glass. Avoid constant immersion. Will it damage paintIt can if paint is weak or not fully cured. Test first and remove slowly with heat to soften the adhesive. Can it hold shelvesThis tape is ideal for light mounting and trim. Use mechanical fixings for shelves and heavy items.
$22.74 $17.05
Fast, tough and tidy. This bright white duct tape delivers a strong hold for patching, bundling, sealing and quick fixes indoors and outdoors. It tears by hand for easy application and leaves a clean look on light surfaces. Strong hold for everyday repairs and jobsite tasks Weather resistant backing that helps shed moisture UV resistant colour that stays bright in the sun Hand tear across or along the roll for fast use Conforms to rough, uneven and curved surfaces Clean white finish blends with trim, appliances and walls Great for Sealing and patching around the home, site and shed Temporary cable bundling and gear organisation Quick fixes on tools, hoses, tarps and camping gear Labelling and marking on light coloured surfaces Craft, props and event setups where a white finish is preferred Surface Compatibility Adheres to most clean, dry surfaces including metal, plastic, painted timber, vinyl, glass, masonry, cardboard and fabric. Not recommended on freshly painted walls, delicate finishes, porous stone or where residue free removal is essential. How to Use Clean and dry the surface. Remove dust, oil and loose flakes. Unroll and press the tape down firmly as you go to avoid air pockets. For heavy duty holds, wrap or overlap the tape to increase grip. To remove, lift a corner and peel back slowly at a low angle. Pro Tips At cooler temperatures, warm the tape and surface for best tack. For long term outdoor use, apply to smooth, sealed surfaces. Test first on sensitive areas to check finish and removal. Specifications Brand T-Rex Product type Duct tape Colour White Width 48 mm Length 9.1 m Use Indoor and outdoor Finish Matte white What is in the Box 1 x Roll of T-Rex White Duct Tape 48 mm x 9.1 m Frequently Asked Questions Will it hold in the rain?The backing helps resist moisture and the adhesive bonds well to dry, prepared surfaces. Apply to a clean, dry surface for best results. Is it paintable?Many users paint over duct tape for temporary cosmetics. For the best finish, use a suitable primer and test first. Will it leave residue?Like most strong duct tapes, residue can occur, especially after long exposure to heat and sun. Test on sensitive finishes and remove slowly.
$17.05 $14.74
Ramboard Joining Tape is the professional solution for connecting and securing surface protection sheets during construction, renovation, and painting projects. Designed for durability and clean removal, this high-performance tape ensures that your floor and surface coverings stay firmly in place without causing damage or leaving residue. Key Features Strong adhesive for secure bonding between Ramboard sheets Leaves no residue on most surfaces when removed properly Durable and tear-resistant for high-traffic job sites Easy to apply and unwind for fast installation 72mm width for reliable coverage and sealing Ideal For Construction and renovation projects Protecting floors, tiles, and finished surfaces Commercial and residential applications Why Choose Ramboard Tape? This joining tape is engineered to complement Ramboard surface protection products, delivering a tight seal that keeps dust, debris, and spills away from protected surfaces. It is designed to perform under tough site conditions while being easy to remove once the job is done. Specifications Width: 72mm Length: Varies by roll Colour: Brown Adhesive Type: Pressure-sensitive Residue-Free Removal: Yes Pro Tip For best results, apply Ramboard Joining Tape only to Ramboard and not directly to finished floors. Always ensure surfaces are dry and free of dust before application.
$30.65 $23.62
Keep jobs moving with a reliable, multipurpose PVC duct tape built for quick fixes and everyday maintenance. Paint Partner PVC Duct Tape bonds fast, conforms to uneven surfaces, and helps you seal, bundle, repair, and patch with confidence on site or at home. Why you will like it Strong instant hold grips to plastics, metal, timber, cardboard, and painted surfaces. Tear by hand for fast application when you do not have a knife handy. Flexible PVC backing conforms around pipes, ducts, cables, edges, and corners. Good weather resistance suitable for indoor use and light outdoor tasks. Clean removal designed to leave minimal residue when removed within a reasonable time. Low shine finish helps reduce glare on stage, sets, and job sites. Great for Sealing ducting joins and flexible hose connections Temporary patching of tarps, plastic sheeting, and packaging Bundling cables and securing drop sheets Edge protection on work surfaces and tool cases Quick fixes on site, in workshops, sheds, and vehicles Surface compatibility Adheres well to smooth, clean, and dry surfaces including PVC, PE sheeting, aluminium, steel, timber, painted walls, and cardboard. Test first on delicate or freshly painted areas. How to use Clean and dry the surface. Remove dust, oils, and loose paint. Unroll and tear or cut the required length. Press down firmly and smooth from the centre out to remove air pockets. For joints or patches, overlap edges by at least 20 mm. To remove, peel back slowly at a low angle. Remove within a reasonable time for the cleanest results. Tips For extra hold on porous surfaces, apply additional pressure with a roller. Avoid prolonged exposure to strong UV and high heat if a pristine finish is required. Not a substitute for permanent structural repairs or certified electrical insulation. Product details Backing PVC Adhesive Rubber based Finish Low sheen Use Indoor and light outdoor tasks Removal Minimal residue when removed within a reasonable time FAQs Is it waterproofIt resists moisture and splashes for temporary sealing. For long term underwater or high pressure sealing, choose a dedicated waterproof repair product. Can I paint over itMost paints will not adhere well to PVC tape. Remove the tape after painting or mask with a paintable tape. Will it damage surfacesOn most sound surfaces it removes cleanly when taken off in a reasonable time frame. Always test first on delicate, aged, or freshly painted surfaces. Good to know Store in a cool, dry place out of direct sunlight. Apply between 10°C and 35°C for best results.
$4.64 $3.63
Keep jobs moving with a reliable, multipurpose PVC duct tape built for quick fixes and everyday maintenance. Paint Partner PVC Duct Tape bonds fast, conforms to uneven surfaces, and helps you seal, bundle, repair, and patch with confidence on site or at home. Why you will like it Strong instant hold grips to plastics, metal, timber, cardboard, and painted surfaces. Tear by hand for fast application when you do not have a knife handy. Flexible PVC backing conforms around pipes, ducts, cables, edges, and corners. Good weather resistance suitable for indoor use and light outdoor tasks. Clean removal designed to leave minimal residue when removed within a reasonable time. Low shine finish helps reduce glare on stage, sets, and job sites. Great for Sealing ducting joins and flexible hose connections Temporary patching of tarps, plastic sheeting, and packaging Bundling cables and securing drop sheets Edge protection on work surfaces and tool cases Quick fixes on site, in workshops, sheds, and vehicles Surface compatibility Adheres well to smooth, clean, and dry surfaces including PVC, PE sheeting, aluminium, steel, timber, painted walls, and cardboard. Test first on delicate or freshly painted areas. How to use Clean and dry the surface. Remove dust, oils, and loose paint. Unroll and tear or cut the required length. Press down firmly and smooth from the centre out to remove air pockets. For joints or patches, overlap edges by at least 20 mm. To remove, peel back slowly at a low angle. Remove within a reasonable time for the cleanest results. Tips For extra hold on porous surfaces, apply additional pressure with a roller. Avoid prolonged exposure to strong UV and high heat if a pristine finish is required. Not a substitute for permanent structural repairs or certified electrical insulation. Product details Backing PVC Adhesive Rubber based Finish Low sheen Use Indoor and light outdoor tasks Removal Minimal residue when removed within a reasonable time FAQs Is it waterproofIt resists moisture and splashes for temporary sealing. For long term underwater or high pressure sealing, choose a dedicated waterproof repair product. Can I paint over itMost paints will not adhere well to PVC tape. Remove the tape after painting or mask with a paintable tape. Will it damage surfacesOn most sound surfaces it removes cleanly when taken off in a reasonable time frame. Always test first on delicate, aged, or freshly painted surfaces. Good to know Store in a cool, dry place out of direct sunlight. Apply between 10°C and 35°C for best results.
$4.55 $3.63
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load): – At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area – At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$143.34
Dunlop Pressure Sensitive Carpet Tile Adhesive 2L Dunlop Carpet Tile Adhesive is a high strength, water based pressure sensitive adhesive designed for carpet tiles and double bonded underlay systems. It tacks off to a clear, dry-to-touch film that grips firmly yet allows tiles to be lifted and replaced for maintenance. Key features Pressure sensitive grab for secure hold and easy tile replacement Water based, low odour, easy to apply Suitable for smooth or textured tile backings and composition vinyl tiles Works with double bonded underlays in commercial fitouts Suitable substrates Concrete, plywood, fibre cement sheet, compressed fibre cement, and suitable underlay sheets. Subfloors must be dry, smooth, clean, and prepared to AS 1884 requirements including moisture testing. Coverage Approx. 10 m² per 2 L using a 1.6 mm V notched trowel Approx. 14 m² per 2 L using a long nap roller Drying and traffic Allow adhesive to become tacky and transparent before laying tiles. Typical tack off time is 2 to 4 hours depending on conditions. Heavy foot traffic after 24 hours Avoid wet cleaning or water exposure for 48 hours Application guide Prepare the subfloor. Prime very porous substrates if required. Treat rising damp or green concrete with a suitable moisture barrier. Apply adhesive evenly: Textured backs, composition vinyl tiles, and double bond underlays: 1.6 mm V notched trowel held at about 60 degrees Smooth backed tiles: long nap roller Wait until the film is tacky and clear with no transfer to fingertips. Early placement into wet adhesive will create a more permanent bond. Lay tiles, cut and reposition as required, then roll in both directions with a suitable roller to ensure full contact. Clean up Clean tools immediately with warm soapy water. Remove dried residue with mineral turps. Storage and shelf life 12 months in unopened packaging when stored in a cool, dry place at about 23°C and 50% RH. Good to know Do not apply below 15°C or above 30°C surface temperature. Not suitable for traditional carpet-to-underlay stretch-in installations. For double bond systems, follow the flooring manufacturer’s instructions. Safety Wear gloves and eye protection, ensure adequate ventilation, and keep out of reach of children. If eye contact occurs, rinse with water and seek medical advice if irritation persists.
$38.56
Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$34.90
SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sika High-Strength for your next project Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing studs, battens, and sheets Filling small gaps while bonding Fast installation where speed saves labour Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber and masonry Concrete and fibre cement Many building materials except PE and PP Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications. Temperature and environmental performance Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$31.50
Bastion High-Bond Stud Adhesive 5.2 kg is a reliable stud adhesive for fixing plasterboard to timber or metal framing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5.2 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Bastion High-Bond for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Bastion High-Bond Stud Adhesive 5.2 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Plasterboard installation on studs Reducing screw count by bonding and fixing together Renovations where clean bond lines are important Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber studs Galvanised metal studs Plasterboard back surfaces Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of work within the wet time window to ensure transfer. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Applies as a bead to studs. Press board into place and fix with screws while the adhesive is wet. Final cure occurs as the solvent or moisture leaves the bead. Temperature and environmental performance Use in dry, shaded conditions during lining work. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh smears with a suitable cleaner. Trim cured squeeze out before finishing. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store closed and away from heat sources. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$29.39
Davco SMP Evo Flexible Tile Adhesive 5 kg is a reliable polymer modified flexible tile adhesive for demanding substrates chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Davco SMP for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Davco SMP Evo Flexible Tile Adhesive 5 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms, kitchens, and balconies Tiling over existing tiles where movement accommodation is needed Floor and wall applications Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete and screeds Fibre cement sheeting Existing glazed tiles after scuffing and cleaning Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of per data on the bag, adjust for weather. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Observe open time, bed thickness, and traffic restrictions. The polymer modification gives improved flexibility once cured. Temperature and environmental performance Install in moderate conditions and shield fresh work from wind and direct sun. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Water clean-up while fresh. Remove haze before it hardens. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep the bag closed and dry between uses. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$26.38
Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gorilla Ultimate for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Furniture build and repair Edge bonding and laminations Cabinetry and joinery where water resistance is valued Suitable surfaces The adhesive works well on the following surface types when properly prepared: Hardwoods and softwoods Plywood and MDF Veneers and end grain with correct technique Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured. Temperature and environmental performance Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$25.20
BBQ Tough Clean Grease & Grime Spray 400 g Bring your grill back to spotless condition with BBQ Tough Clean. This powerful, non-caustic formula is specially designed to lift away grease, fat, and charred food from BBQ plates, grills, and racks, giving you a cleaner and healthier cooking surface without harsh fumes. Key Benefits: Powerful cleaning: Penetrates and dissolves stubborn grease and grime. Spotless results: Leaves BBQ surfaces residue-free for safer cooking. Non-caustic & low fume: Safer to use around your outdoor cooking area. Cold application: Designed to work when the BBQ is cool (before use). Perfect For: Stainless steel and cast iron BBQ plates, grills, and racks Removing built-up food, grease, carbon deposits Deep cleaning before a big barbecue or regular maintenance How to Use: Make sure your BBQ is cold. Remove the racks, grills and plates if possible. Scrape off excess debris and wipe loose grease. Shake the can well and spray liberally onto the surface from upright position. Allow to sit at least 10 minutes (for tough grime, up to 2 hours), then wipe with a damp cloth or scouring pad. Rinse thoroughly with water and dry with a clean cloth. Optional: apply a light coat of cooking oil to surfaces to protect against corrosion. Important Safety & Usage Notes: Do not use on hot BBQs Avoid spraying on painted, plastic or aluminum surfaces. If overspray lands on unintended areas, wipe off immediately and rinse. Not intended for use on exterior, non-cooking surfaces (use an exterior BBQ cleaner for those parts). Keep out of reach of children and pets. Use protective gloves and avoid inhaling fumes.
$7.02
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$37.95
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
$33.09
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
$16.48
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force. FEATURES: Extreme tensile strength 1 loop of tape holds 700+ pounds of weight Made with patented Forge-Link™ Technology Waterproof backing High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure UV resistant materials
$36.00
Our Quick Setting Gel Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product fills gaps and covers large porous surfaces. The final cure colour is cream but can be mixed with paint to colour match. This product sets in only 5 minutes. Works best on: • Porous materials • Ceramic • Metal • Pottery • Wood • Tile • Crafts Properties: Initial colour: Green resin/white hazy hardener Maximum Gap: .25” Final colour: White hazy Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 1500 psi (± 20%) Handling Time: After 1 hour Aluminum: 900 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-320 to 3000F (-360 to 1490C) Instructions: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly approximately 1 minute. Use package blister or clean cardboard for mixing container, do not use metal. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F / 25C) with full cure in 24 hours. Helpful Hints: To colour Epoxy Gel, do test sample using mixed epoxy with added small amounts of colourant, such as paint (latex or oil), stain or tint. Mix well & apply to scrap piece of wood. Let dry to compare the final colour to the color of repair item. Keep testing until a colour match is achieved, then mix the appropriate amount of colourant with Epoxy Gel and bond repair item.
$9.95
You have seen 144 out of 244 products
High-strength, trade-grade adhesives, sealants and repair systems for demanding jobs. Prioritise structural strength, durability and temperature/chemical resistance. Use filters to narrow by chemistry and cure profile. Always consult the product page and TDS/SDS.
