Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.
$79.80
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Bastion Premixed Tile Adhesive 15 kg Overview Bastion Premixed Tile Adhesive 15 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$55.64
Protite Mould Defender Anti-Fungal Paint Additive 75 mL is a reliable liquid paint additive that helps inhibit mould growth in humid areas chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 75 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Protite Mould for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Protite Mould Defender Anti-Fungal Paint Additive 75 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms and laundries Kitchens and food prep zones Rental refresh and maintenance work Suitable surfaces The adhesive works well on the following surface types when properly prepared: Walls and ceilings coated with water based paint Suitable primers as per paint maker guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of Work to normal paint tray timelines. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix thoroughly into your chosen paint and apply as directed by that paint. Dry and recoat times follow the paint system. Temperature and environmental performance Use within the temperature window recommended for the host paint. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean rollers and brushes according to the paint manufacturer's advice. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store upright with cap tight. Do not allow to freeze or overheat. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.64
Power Through Soap Scum & Kill 99.9% of Germs Selleys Complete Clean Bathroom & Shower Spray is a household-grade disinfectant cleaner that cuts through tough soap scum, dirt and grime while killing 99.9% of common bathroom germs (S. aureus and E. coli). Ideal for showers, bathtubs and toilets for a sparkling clean finish. Disinfects effectively: Kills 99.9% of germs (S. aureus & E. coli). Fast soap scum removal: Powers through built-up residue on bathroom surfaces. Household-grade disinfectant: Designed for hard, non-porous bathroom surfaces. Where to Use Suitable for hard, non-porous surfaces such as: showers, bathtubs, toilets and similar bathroom fixtures. Not Suitable For Marble, natural stone, porous tiles or aluminium surfaces Polished, varnished or lacquered surfaces Skin (hard surface disinfectant only) Directions Turn nozzle to ON while directing trigger away from face. Spray directly onto the surface until fully covered. For cleaning: wipe with a clean damp cloth or rinse. For disinfecting: allow 10 minutes contact time, then wipe with a clean damp cloth. On food-contact areas: rinse or wipe with a clean damp cloth after 10 minutes. Good to Know Always test on an inconspicuous area first. Avoid prolonged contact with sensitive surfaces listed above. Keep out of reach of children. Read label before use. Product Details Brand: Selleys Range: Complete Clean Type: Bathroom & shower disinfectant spray Size: 750mL trigger spray
$6.83
Tarzan's Grip Mounting Tape is a double sided, heavy duty, high strength tape that instantly grabs for easy, fast and permanent mounting. It is ideal for a multitude of surfaces, including metal, wood, rubber, leather, china, brick, stone, plasterboard and most plastics. Extremely strong Instant grab Solvent free Permanent
$12.42
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$24.57
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$14.99
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
$22.00
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.78
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$23.38
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$9.33
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$185.00
Multi-Purpose Cleaner and Deodorizer Natural Minerals easily dissolve in water Directions: Test on an inconspicuous area first Borax can be used in powder form for tea and coffee cup stains General cleaning 1-table spoon to 4.5 Litres of warm water (also woollens and blankets) Enamel surfaces 4 tablespoons to 4.5 Litres of warm water (refrigerators, stoves, sinks, baths & tiles Uses: General cleaning, stain remover, deodorizer
$9.47
Directions: - Use gloves before dispensing - Washing Machines: empty machine, add 1 tablespoon of Descaling powder directly into the machine, not detergent dispenser. Run full cycle - Dishwashers: remove all items from the machine, including all dishwashing detergents. Fill detergent dispenser with up to 2 tablespoons of Descaling powder and run for a full cycle. - All-purpose cleaner: 1 tablespoon mix to 1 Litre hot water and soak items for up to 3 - 5 minutes, rinse the solution off in cold water Uses: Can be used undiluted for heavy stains by simply adding power and rob directly onto affected area e.g. bathtubs, sinks and toilet bowls
$11.48
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.61
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs Key Features Excellent bond to glass Acetic cure for optimal sealing Designed for interior and exterior use UV resistant and shrink-proof Specifications Colour Black Model Name Parfix Window and Glass 300g Model Number 9300697122445 Material Silicone polymer Paintable No Stainable No UV Resistant Yes Outdoor Yes Indoor Yes Shrink Resistant Yes Sandable No Applications Suitable for use on windows, glass partitions, and glass blocks. Instructions For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
$12.48
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$6.28
High-Performance Multipurpose Wall & Floor Tile Adhesive This versatile adhesive is designed for fixing almost all tile types to a wide range of challenging surfaces, including water features and swimming pools. Key Features: Suitable for both walls and floors Can be applied over difficult surfaces, including water features Allows tiling over existing tiles Compatible with most types of ceramic and natural stone (excluding moisture-sensitive stone) Tile Types: Ceramic tiles Fully vitrified tiles Natural stone (excluding moisture-sensitive stone) Mosaics Porcelain Suitable Surfaces: Existing tiles Glazed ceramic tiles Metal Roughened fibreglass Timber (particleboard only) Application Areas: Walls and floors Indoor and outdoor Water features and swimming pools Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.4m²/kg 250 x 250mm and larger 10-12mm 0.25m²/kg
$49.42
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$77.97
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.80
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
The Hotwire Floor Heating Mat delivers all the comfort of Hotwire under tile heating with the heating cable already pre-spaced on a self-adhesive fibreglass mesh. Instead of fixing a loose cable, you simply roll the mat out across the floor — installation is fast, spacing is guaranteed even, and the finished system is invisible, silent, dust-free and energy efficient. At just 3.6 mm thick, the mat adds almost no height to the floor build-up, and the single cold tail keeps wiring simple. Every mat is supplied as a complete system with a fully programmable touch screen thermostat, floor temperature probe, installation alarm, tape and manual; WiFi and dual thermostats are available as upgrades.Where to use itPerfect for bathrooms, ensuites, laundries, kitchens and living areas under tile or stone. The ultra-thin profile makes it equally suited to new builds and retrofits in existing homes where floor height is limited, and the gentle radiant heat also dries wet-area floors, helping keep mould at bay.How to useMeasure the free floor area, roll the mat out and press the adhesive mesh onto a clean, primed subfloor, cutting the mesh (never the cable) to turn at walls. Fit the floor probe, then tile directly over the mat. All wiring, thermostat connection and testing must be completed by a licensed electrician, with resistance readings recorded before, during and after tiling.Important notesSize the mat to the open floor area only, excluding vanities, baths and fixed cabinetry. The heating cable must not be cut or shortened. Register your warranty after installation; the heating element is covered by a lifetime warranty (conditions apply).Specifications Wattage Coverage 300 W 2 m² 450 W 3 m² 600 W 4 m² 900 W 6 m² 1200 W 8 m² 1500 W 10 m² SafetyIndoor use only. This mat connects to 230–240 V mains and must be installed and wired by a licensed electrician to AS/NZS wiring rules on an RCD-protected circuit. Hotwire systems are independently tested to AS/NZS standards.
$873.06 - $1,723.38
The Hotwire Under Tile Heating Kit is a complete electric floor heating system built for Australian homes. A slim 4 mm heating cable is laid directly over the subfloor before tiling, so the warmth sits just below the floor surface and the room heats up in around 30–60 minutes. Each kit ships with everything needed for a professional result: the heating element, a fully programmable touch screen thermostat with floor temperature probe, installation alarm, fixing tape and manual. Running costs can be as low as a couple of cents per square metre per hour, and a WiFi thermostat upgrade is available.Where to use itIdeal for bathrooms, ensuites, laundries, kitchens and living areas — anywhere tiled floors feel cold underfoot. Because the heating warms and dries wet-area floors, it also helps reduce mould and cleaning. It suits renovations particularly well, since only the floor covering needs to be replaced to install it, and systems scale from a compact 1 m² zone up to large open-plan spaces.How to usePlan the heated area, fix the cable evenly across the subfloor at the spacing shown in the manual, position the floor probe, then tile or screed over the element. All electrical connections and the final wiring of the thermostat must be carried out by a licensed electrician, and continuity/resistance tests should be logged before, during and after installation.Important notesChoose the kit wattage to match the free floor area, excluding fixtures such as vanities, baths and cabinetry. Do not shorten or cut the heating cable. Register the warranty after installation; the heating element carries a lifetime warranty (conditions apply).Specifications Wattage Coverage (approx.) 300 W 1.4–2 m² 600 W 3.4–4 m² 1000 W 6.1–7 m² 1500 W 9–10.7 m² 3000 W 17.9–21.4 m² 6000 W up to approx. 42 m² SafetyIndoor use only. This is a 230–240 V fixed-wiring appliance: installation and connection must be performed by a licensed electrician in accordance with AS/NZS wiring rules, with the circuit protected by an RCD. Independently tested to AS/NZS standards.
$0.00 - $2,756.05
Dunlop Matte Silicone is a flexible acetic-cure sealant with an elegant matte finish, made for modern tiles and grouts where a shiny silicone bead would look out of place. Available in four designer colours — White, Grey, Silver Grey and Anthracite — it lets the sealant line sit quietly against matte porcelain, stone-look tiles and contemporary grout colours while still delivering strong adhesion and dependable waterproofing.Where to use itIdeal for wall and floor junctions, tiled surfaces, benchtops, bath edges, cupboards, splashbacks and movement joints up to 30mm wide. It is mould resistant, UV and weather resistant, and suitable for both indoor and outdoor use, including wet areas. It bonds well to ceramic tiles, glass, enamel, anodised aluminium, granite, porcelain and sanitary acrylics.How to usePrepare joints so they are clean, dry and free of dust, grease and old sealant residue. Cut the cartridge tip and nozzle to match the joint width, fit the cartridge in a caulking gun and run a smooth, continuous bead along the joint. Tool it off promptly before a skin forms, remove masking tape straight away, and let the silicone cure fully before use in wet areas.Important notesBeing an acetic-cure silicone, it must not be used under waterproofing membranes or with mirrors, as the cure can damage those surfaces — use a neutral-cure silicone there instead. Maximum joint size is 30mm wide by 15mm deep.Specifications Size 310ml cartridge Max joint width 30mm wide x 15mm deep Cure type Acetic cure silicone, matte finish SafetyEnsure good ventilation during application and avoid skin and eye contact with uncured sealant. Keep away from children and consult the Safety Data Sheet available from Dunlop Trade before starting work.
$30.99
Dunlop Coloured Silicone is a flexible acetic-cure sealant designed to finish and protect the joints that grout alone cannot handle. Because the colour range is matched to the Dunlop Coloured Grout palette, you can seal wall junctions, bath edges and benchtop joints in a shade that blends seamlessly with your tiling for a clean, coordinated finish. It applies easily from a standard 310ml cartridge, bonds strongly, stays waterproof and is backed by a 10 year guarantee.Where to use itUse it on wall and floor junctions, tiled surfaces and benchtops, bath edges, cupboards, splashbacks and movement joints, both indoors and outdoors. It is waterproof and suitable for use in showers, and offers strong adhesion to ceramic tiles, glass, enamel, anodised aluminium, granite, porcelain and sanitary acrylics.How to useMake sure joints are clean, dry and free of dust, old sealant and excess adhesive. Cut the cartridge tip and nozzle to suit the joint width, load into a caulking gun and apply a continuous bead into the joint. Tool the bead smooth within a few minutes of application, before a skin forms, and remove any masking tape immediately. Apply at temperatures between 5°C and 40°C and allow the silicone to cure fully before exposing it to water.Important notesThis is an acetic-cure silicone, so do not use it under waterproofing membranes or against mirror backings, as it can damage those surfaces — choose a neutral-cure silicone for such jobs. Suits joints up to 30mm wide and 15mm deep.Specifications Size 310ml cartridge Max joint width 30mm wide x 15mm deep Cure type Acetic cure silicone SafetyUse in a well-ventilated area and avoid contact with skin and eyes while uncured. Keep out of reach of children and refer to the Safety Data Sheet on the Dunlop Trade website before use.
$29.25 - $31.00
Dunlop Grout Paint is the quick, budget-friendly way to make a tiled area look new again without raking out old or discoloured grout. The acrylic formula paints straight over existing grout lines with the built-in brush applicator, offering excellent opacity that covers even dark colours in a coat or two. Clean-up is easy, and a single 250ml bottle refreshes a surprisingly large area.Where to use itUse it over old or discoloured cement grout on indoor walls and floors and on outdoor walls. It is perfect for freshening bathrooms, kitchen splashbacks and laundry tiling, or for switching grout colour - brightening joints with Ultrawhite or going darker with Slate Grey or Jet Black for a modern contrast.How to useClean the grout thoroughly (Dunlop Tile & Grout Cleaner works well) and let it dry. Shake the bottle, then brush the paint along the grout line with the applicator, overlapping slightly onto the tile edge. Once touch dry - about 15-20 minutes at 23°C - wipe the overpainted edges off the tile faces with a damp cloth. Allow 2 hours' cure after cleaning, then polish the area with a soft cloth. The paint is fully set after 24 hours, after which showers can be exposed to water.Important notesNot suitable for swimming pools or external floors. Expect faster wear in areas with regular foot traffic or frequent exposure to water, soaps and chemicals such as shower floors. Coverage varies enormously with joint width and tile size - from about 1m² on small mosaic tiles with wide joints up to 200m² on large-format tiles with fine joints.Specifications Use on Old or discoloured grout joints Coverage guide Approx. 60m² per 250ml for 330 x 330mm tiles at 3mm joints Tile types Grout joints between most glazed ceramic and porcelain tiles Location Indoor walls and floors, outdoor walls SafetyAvoid contact with eyes and prolonged skin contact; wear gloves if desired and wash hands after use. Use with adequate ventilation, keep out of reach of children and refer to the Safety Data Sheet.
$18.71
Dunlop Flexible Coloured Grout in the trade-size 15kg bag is built for big tiling jobs - whole houses, commercial floors and multi-room renovations. It is the same flexible, smooth-finish formula tilers rely on, with a stronger colour system for rich, even grout lines and Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth in wet areas. The grout works easily, ensures flush joints and leaves no pin holes.Where to use itSuitable for walls and floors, indoors and outdoors, over ceramic, porcelain, marble, granite and mosaic tiles. With a working range of 1mm to 8mm joints it handles fine wall tiling through to wide-format floor tiles, and the grey tones (Misty Grey and Slate Grey) are popular choices for high-traffic floors where joints need to hide everyday wear.How to usePrepare clean, dry joints raked free of adhesive. Mix with clean water to a smooth paste - or with Dunlop Primer & Additive to boost colour, flexibility, adhesion and stain resistance. Apply diagonally with a rubber grout float, pack joints full, remove excess, then sponge the tiles clean once the grout firms and polish off haze. Initial set is around 24 hours, showers can be wet after 3 days, and full cure is reached after 7 days.Important notesInclude about 15% wastage in quantity estimates. Mix batches with consistent water content to avoid colour variation across large floors.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based product - alkaline when wet and may irritate skin and eyes. Wear gloves and eye protection, avoid inhaling dust when emptying and mixing the bag, and wash after use. Keep out of reach of children; see the Safety Data Sheet.
$79.95
Dunlop Ultra-White Grout is a non-sanded, flexible cement-based grout that delivers a super smooth, brilliantly white finish between wall and floor tiles. Formulated with Grout Shield anti-mould and anti-bacteria technology, it actively resists the growth of mould and bacteria so joints stay looking cleaner for longer. The cured grout is water repellent, resists dirt pick-up and is easy to wipe clean, making it a favourite for bright, fresh bathrooms and kitchens.Where to use itUse Ultra-White Grout on walls and floors, indoors and outdoors. It is suited to ceramic, porcelain, marble, granite and mosaic tiles, and is designed for narrow tile joints between 1mm and 4mm wide where a fine, non-sanded finish is wanted.How to useEnsure joints are clean, dry and free of dust or adhesive residue. Mix the powder with clean water to a smooth, lump-free paste, then work the grout firmly into the joints on the diagonal using a rubber grout float or squeegee. Remove the excess as you go, then clean the tile faces with a lightly damp sponge once the grout has firmed. Polish off any remaining haze with a soft, dry cloth. Allow the grout to cure fully before exposing wet areas such as showers to water.Important notesCoverage varies with tile size, joint width and joint depth, and a wastage allowance of around 15% should be included when estimating. For wide joints over 4mm choose a sanded or wide-joint grout instead. Pair with Dunlop Grout Sealer for extra stain protection.Specifications Joint width 1 - 4mm Coverage guide Approx. 6.7m² for 300 x 300 x 5mm tiles at 3mm joints (incl. 15% wastage) Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based product - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing dust when mixing, and wash hands after use. Keep out of reach of children and refer to the Safety Data Sheet before use.
$15.23
Dunlop Ultra-White Grout in the 5kg pack is a non-sanded, flexible grout that produces a super smooth, super white finish across larger tiling jobs. It contains Grout Shield anti-mould and anti-bacteria technology to resist mould and bacteria growth, and the cured joint is water repellent and easy to clean, helping white joints stay bright in busy bathrooms, laundries and kitchens.Where to use itSuitable for tile joints on walls and floors, indoors and outdoors. Use it with ceramic, porcelain, marble, granite and mosaic tiles wherever joints are between 1mm and 4mm wide. The 5kg pack size suits full bathroom renovations, splashback runs and floor areas where a 1.5kg pack would run short.How to usePrepare joints so they are clean, dry and raked free of adhesive. Mix the powder with clean water to a smooth, creamy paste and let it stand briefly before remixing. Apply diagonally across the joints with a rubber grout float, pressing the grout in fully and striking off the excess. Once firm, sponge the tile faces clean with minimal water, then buff away the haze with a dry cloth. Keep showers dry until the grout has cured.Important notesEstimate quantities from tile size, joint width and depth and allow roughly 15% extra for wastage. Not intended for joints wider than 4mm. Sealing with Dunlop Grout Sealer after curing improves long-term stain resistance.Specifications Joint width 1 - 4mm Coverage guide Approx. 13.3m² for 300 x 300 x 5mm tiles at 1.5mm joints (incl. 15% wastage) Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid inhaling dust while mixing, and wash thoroughly after handling. Keep out of reach of children and consult the Safety Data Sheet.
$41.03
Dunlop Flexible Coloured Grout in the 5kg pack brings the same smooth finish and strong, consistent colour as the smaller pack, in a size suited to whole bathrooms, kitchens and floor areas. The formula is flexible and easy to work, ensures flush joints with no pin holes, and contains Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth so grout lines stay looking better for longer.Where to use itGrout walls and floors indoors and outdoors with ceramic, porcelain, marble, granite and mosaic tiles. Joints from 1mm to 8mm are covered, making it suitable for everything from fine mosaic work to wide-format floor tiles. In swimming pools, use White 200 mixed with Dunlop Primer & Additive.How to useRake joints clear of adhesive and ensure they are clean and dry. Mix the powder with clean water to a smooth, lump-free paste - or gauge with Dunlop Primer & Additive for enhanced colour, adhesion, abrasion and stain resistance. Work the grout diagonally into the joints with a rubber float, strike off the excess, then sponge clean once the grout firms and buff away residual haze. Initial set is about 24 hours, showers can get wet after 3 days, sealing is possible after 3 days and full cure takes 7 days.Important notesAllow roughly 15% wastage when estimating coverage from tile size, joint width and depth. Keep mixing water consistent between batches for uniform colour.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid dust when mixing, and wash hands after use. Keep out of reach of children and consult the Safety Data Sheet.
$41.03
Dunlop Universal Tile Adhesive is the do-almost-anything adhesive in the Dunlop Trade (ARDEX Australia) range – a high performance, multipurpose wall and floor tile adhesive with excellent workability and flexibility. Its non-slumping formula keeps wall tiles in position while its C2TES1 classification delivers extended open time, slip resistance and a deformable, high-strength bond for demanding applications.Where to use itOne of the most versatile adhesives available: suitable for indoor and outdoor walls and floors, and even swimming pools. It fixes ceramic, porcelain, natural stone (excluding moisture sensitive stone), mosaics and fully vitrified tiles over compressed fibre-cement sheet floors, concrete floors, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render.How to useMix with clean water to a smooth, creamy consistency and allow to stand briefly before a final remix. Apply to a clean, dry, sound substrate with a 6mm notched trowel on walls or a 10mm notched trowel on floors. Press tiles firmly home with a twisting action, ensuring good adhesive transfer to the tile back – especially important outdoors and in pools where full contact is required. Grout after approximately 24 hours at 23°C and 50% relative humidity.Important notesNot suitable for moisture sensitive natural stone. For pool installations, allow the full recommended cure before filling. The product exceeds ISO 13007 requirements.Specifications Size 20kg bag Colour White Coverage 11m² per 20kg (6mm trowel); 7m² per 20kg (10mm trowel) Tile types Ceramic, porcelain, non-sensitive stone, mosaics, fully vitrified Substrates Concrete, compressed FC floors, FC walls, waterproofing, plasterboard, render Classification C2TES1 tile adhesive; exceeds ISO 13007 SafetyContains cement. Avoid breathing dust and avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection while mixing and applying, and work in a well-ventilated area. Refer to the safety data sheet before use.
$59.68
Dunlop Trade Resaflex is a multipurpose, rubber modified tile adhesive from Dunlop Trade (ARDEX Australia), trusted by professional tilers for decades. Its rubber modified cement formulation delivers a strong yet flexible bond that tolerates normal building movement, and its C2S1 classification confirms improved adhesion and deformability. One bag covers a wide range of everyday tiling jobs, which is exactly why it has earned its multipurpose name.Where to use itSuitable for indoor and outdoor walls and floors. Use it to fix ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can also be used over Dunlop Waterproofing and green screed, making it well suited to bathrooms and new-build wet areas.How to useMix the powder with clean water to a smooth, lump-free paste. Spread onto a clean, dry, sound substrate with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles. Bed each tile with a firm twisting action to achieve full contact, and lift a tile occasionally to check coverage. Allow the adhesive to cure before grouting.Important notesNot suitable for moisture sensitive natural stone. Only mix what can be used within the working time and never re-temper stiffened adhesive with extra water.Specifications Size 20kg bag Colour Grey Coverage 0.65m²/kg (6-8mm trowel); 0.4-0.5m²/kg (10-12mm trowel) Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, waterproofing, plasterboard, render Classification C2S1 rubber modified tile adhesive SafetyContains cement. Avoid breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Wash skin after handling and refer to the safety data sheet before use.
$53.15
Dunlop Tiler's Mastic is a premium non-slump tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). Built for the demands of modern tiling, its high-grab, non-slump formula is ideal for today's large format tiles, holding them exactly where you place them on walls while still spreading smoothly and easily on floors. As a C2TES1 classified adhesive it offers extended open time, slip resistance and deformability for a strong, flexible bond.Where to use itSuitable for indoor and outdoor walls and floors, including wet areas over Dunlop Waterproofing. It fixes ceramic, porcelain, non-moisture sensitive natural stone, fully vitrified, mosaic and translucent tiles over cement render, compressed fibre-cement sheet (floors), concrete, Dunlop Undertile Waterproofing, existing ceramic tiles, ceramic tile underlay, fibre-cement sheet (walls) and plasterboard.How to useMix the powder with clean water to a smooth, creamy paste. Trowel onto a clean, dry, sound substrate with a 6 x 6 x 6mm notched trowel for walls or a 10 x 10 x 10mm notched trowel for floors and large tiles. Bed tiles with a firm twisting action, checking contact coverage regularly. Grout after approximately 24 hours.Important notesNot suitable for moisture sensitive natural stone. Ensure substrates are properly prepared and primed where required, and avoid tiling in extreme temperatures.Specifications Size 20kg bag Colour White Coverage 10m² with 6mm notched trowel; 6m² with 10mm notched trowel Tile types Ceramic, porcelain, non-sensitive stone, vitrified, mosaics, translucent Substrates Render, concrete, compressed FC sheet, waterproofing, existing tiles, plasterboard Classification C2TES1 tile adhesive SafetyContains cement – avoid breathing dust and avoid skin and eye contact. Wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Consult the safety data sheet before use.
$40.28
Dunlop Tiler's Rubber Modified is a flexible, rubber modified tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). The rubber modified formulation gives the cured bond extra flexibility to absorb normal substrate movement, while its generous coverage and 6-hour grout time keep jobs moving. Classified C2S1, it is a dependable workhorse for tilers who need strength, flexibility and speed in one bag.Where to use itSuitable for indoor and outdoor walls and floors. It fixes ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, ceramic tile underlay, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can even be used over Dunlop Waterproofing and green concrete, making it handy on fast-track projects.How to useMix with clean water to a smooth, creamy consistency and allow to slake before remixing. Apply to a clean, sound, dust-free substrate using a 6 x 6 x 6mm notched trowel on walls or a 10 x 10 x 10mm notched trowel on floors. Press tiles in firmly with a twisting action and check adhesive transfer on the tile back. Grouting can begin in as little as 6 hours.Important notesNot suitable for moisture sensitive natural stone. Do not add extra water once the mix begins to stiffen, and avoid application in extreme temperatures.Specifications Size 20kg bag Colour Grey Coverage 14m² with 6mm notched trowel; 8m² with 10mm notched trowel Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, CTU, waterproofing, plasterboard, render Classification C2S1 tile adhesive; grout in 6 hours SafetyContains cement. Avoid generating and breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated space. Refer to the safety data sheet before use.
$47.18
Dunlop Super Tileset Plus is a smooth, creamy cement-based wall and floor tile adhesive from Dunlop Trade (ARDEX Australia). Mixing to a workable, easy-spreading consistency, it delivers dependable adhesion for everyday tiling at an economical price, making it a solid choice for renovators and trade users tackling standard wall and floor jobs.Where to use itApproved for both indoor and outdoor use on walls and floors. It suits bathrooms, kitchens, laundries, living areas and patios, and bonds ceramic, porcelain, mosaics, fully vitrified, translucent tiles and natural stone (excluding moisture sensitive stone) over concrete, render, screeds, Dunlop Waterproofing Membranes, fibre-cement sheets and plasterboard.How to useMix the powder with clean water to a smooth, lump-free paste and allow it to stand briefly before remixing. Spread onto a clean, dry, sound substrate with a 6mm notched trowel for walls and smaller tiles, or a 10mm notched trowel for floors and larger formats. Bed tiles firmly with a twisting action and check coverage on the tile back periodically. Grouting can proceed after approximately 24 hours at 23°C and 50% relative humidity.Important notesDo not tile over moisture sensitive natural stone with this adhesive, and avoid tiling in extreme temperatures or onto frozen or saturated substrates. Only mix as much adhesive as can be used within its working time.Specifications Size 20kg bag Colour Off-white Coverage 9m² per 20kg (6mm trowel); 6m² per 20kg (10mm trowel) Tile types Ceramic, porcelain, mosaics, vitrified, translucent, non-sensitive stone Substrates Concrete, render, screeds, Dunlop membranes, FC sheet, plasterboard Classification Exceeds C1 Australian Standard SafetyContains cement. Avoid breathing dust and avoid contact with skin and eyes – wear protective gloves, clothing and eye protection when mixing and applying. Mix in a well-ventilated area and refer to the safety data sheet before use.
$36.00
Dunlop Wall & Floor Tile Adhesive is a high performance, ready-mixed adhesive from Dunlop Trade (ARDEX Australia) that takes the hassle out of fixing most tile types. Supplied in an easy-to-handle 8kg pail, it is specially formulated to bond ceramic, porcelain, mosaics, fully vitrified tiles and natural stone (excluding moisture sensitive stone), and its highly flexible formulation copes with the small movements that occur in everyday walls and floors.Where to use itSuitable for indoor walls and floors, and outdoor areas provided there is no standing water and sufficient fall for run-off. It bonds over an impressive range of surfaces: cement render and concrete, fibre-cement sheets, existing ceramic and vinyl tiles, Dunlop Undertile Waterproofing, prepared metal surfaces, oil-based painted surfaces, plasterboard and suitably prepared interior timber.How to useMake sure the substrate is clean, dry and free of dust or grease. Spread the adhesive with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles, then bed tiles in firmly with a twisting motion. Work in small sections so a skin does not form before tiling.Important notesDo not use over strip timber floors. Prime particleboard and plywood sheet floors with Dunlop Tile-All before tiling. For fully immersed or pool applications choose a cement-based Dunlop adhesive instead.Specifications Size 8kg pail Colour Grey Coverage 0.8m²/kg (6-8mm trowel); 0.5m²/kg (10-12mm trowel) Tile types Ceramic, porcelain, mosaics, fully vitrified, natural stone (non moisture sensitive) Substrates Concrete, render, FC sheet, existing tiles, vinyl, metal, plasterboard, prepared timber Format Premixed dispersion adhesive SafetyWork in a well-ventilated area, wear gloves and eye protection, and avoid prolonged skin contact. Wash tools and hands with water before the adhesive dries. Keep out of reach of children and consult the SDS before use.
$93.46
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Premixed Mastic Tile Adhesive is a high performance, ready-to-use wall tile adhesive from Dunlop Trade (ARDEX Australia). Supplied in a convenient 20kg pail, there is no mixing, no mess and no guesswork – just open the lid and start trowelling. Its superior non-slump formulation holds even large format wall tiles and dimensional stone such as marble and granite firmly in place while you work, and its high flexibility and tenacity make it a favourite with tilers who want dependable grab straight off the trowel.Where to use itDesigned for indoor walls only. It is ideal for bathrooms, kitchens, laundries and splashbacks, and its unique formulation allows use in wet areas. Fix ceramic wall tiles, granite and marble (excluding moisture sensitive stone) over cement render, plasterboard, fibre-cement sheet, suitably prepared painted surfaces and Dunlop Waterproofing Membrane (porous tiles only).How to useEnsure surfaces are clean, dry and sound. Spread the adhesive with a suitable notched trowel, working in manageable sections, then press tiles firmly into the ribs with a slight twisting action. Adjust tiles within about 45 minutes of laying (at 23°C and 50% humidity). The adhesive dries in approximately 24 hours depending on temperature, and the porosity of the surface and tiles, after which grouting can proceed.Important notesDo not use over waterproofing membranes with dense or glazed tiles – use porous tiles only, as the adhesive will not dry properly between two non-absorbent layers. Not suitable for floors or exterior applications.Specifications Size 20kg pail Colour White Coverage Approx. 8-10m² per 20kg Tile types Ceramic wall tiles, granite, marble (not moisture sensitive stone) Substrates Render, plasterboard, FC sheet, painted surfaces, Dunlop membrane (porous tiles) Classification D2TE dispersion adhesive SafetyUse in a well-ventilated area and wear protective gloves and eye protection. Avoid skin and eye contact, wash hands after use and keep out of reach of children. Refer to the safety data sheet before use.
$99.60
You have seen 96 out of 189 products
Products suited to bathroom & laundry environments. Choose sealants, adhesives and accessories that match moisture, temperature and movement demands in bathroom & laundry areas. Look for mould resistance, flexibility, UV stability or potable‑water suitability where shown. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
