In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material.
Uses
Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc.
Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems.
Technical Features
Will not discolour mirrors
Heat and steam resistance
Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings
Adheres and forms a durable seal between sheet metals
Gap filling on uneven surfaces
Forms flexible/shock resistant bonds
UV resistant
Low odour during application
Non corrosive
Weather resistant
Application Tips
All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling.
Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm).
Fit nozzle to cartridge. Place cartridge into caulking gun.
Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day).
APPLICATION FOR MIRRORS
For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart
When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them.
Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes)
The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours.
Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure
Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling.
Not recommended for fixing vinyl back mirrors
If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed.
GENERAL APPLICATION
Apply as for mirrors and press surfaces together immediately
Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond)
Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day.
Technical Details and Performance
Indicative information only, not to be used for setting specifications.
Consistency (As applied)
Non-slump, solvent free paste
Curing Mechanism
Very rapidly develops an adhesive bond by reaction with moisture from the air
Curing Rate
2mm depth per day
Skin Forming Time
5-10 minutes (depending on weather conditions)
Service Temperature
–60°C to +150°C
Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area)
After 24 hrs: 280KPa
After 48 hrs: 550KPa
After 7 days: 830KPa
Coverage
15 metres of a 5mm diameter bead
Cleaning
Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort
Where can this product be used?
Use 3 in 1 for sealing, bonding and filling almost any material
damp or dry,inside or outside
Provides a durable waterproof seal
Provides strong bonds and a perfect paintable finish
What materials is this product suitable for?
Glass
Metals
Timber
Brick
Concrete
Tiles
Most plastics (not for polyethylene, polypropylene or teflon)
How to Use
Adhesive
Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure.
Sealant
Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs.
Gap Filler
Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints.
Limitations:
Not recommended for solvent based paints. If required, paint with a water based paint first.
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
Larger, heavier items need to be supported until the adhesive cures.
Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
Clean Up
Uncured product may be removed with mineral turps.
Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Size: 480g Cartridge
Colour: White
Technology Sil-X®
Use: Interior & Exterior
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink.
For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR)
Fill depth: Dependent on mix ratio
Dries in: 2-3 hours
Ready to use: NO (mix with water)
Available in: 500g, 1kg, 2kg & 6kg
Colour: Off-white
• Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key.
• Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate.
• Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge.
• Leave for 2-3 hours before sanding and decorating.
• For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area.
• Clean up with water before filler dries
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out.
For use on: Wood, brick, aluminium, glass, plasterboard, ceramic
tiles and painted surfaces (INTERIOR & EXTERIOR)
Coverage: 30m/3mm bead.
Dry time: Skins in 30 minutes at 25°C. Full cure in 7days.
Ready to use: YES
Available in: 475g
Colour: White
NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps.
• Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant.
• Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap.
• Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth.
• Allow sealant to skin approx 30 min before painting with water-based paints.
• Allow to set for 48 hours if using oil based paint or if joint is large.
• Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting.
• Do not use outside if rain is imminent, not for contantly damp areas.
• Painting improves exterior durability.
• Use Poly silicone sealants for a watertight seal or where movement is excessive.
• Water clean up
Q. How do I fill gaps between my wooden window frames and inside wall?
A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth.
Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened?
A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat.
Q. Why does my gap filler keeps cracking?
A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sandable
Paintable
Ready mixed
Weather resistant
Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home.
Sandable and paintable, it enables a smooth finish.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Paintable
Flexible
Durable
Parfix Gap Filler is a multi-purpose flexible filler that is suitable for interior applications such as skirting and architraves, door and window frames.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very quick setting in 90 seconds
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling
Good chemical resistance
Where can this product be used?
General small household repairs
Fixing gemstones to mounts
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Most Plastics
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately.
Ensure correct caps are replaced on each tube or they will adhere.
Handy tips
Note: For information on how to identify plastics refer to the Selleys plastics guide.
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep a couple at home just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features:
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance:
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product:
General Use
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick.
Safety tips:
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible Fine Coat Render is a high-performance, fibre-reinforced, polymer-modified render that produces a fine, closed finish with superior adhesion and flexibility. The embedded fibres and flexible polymers allow the render to tolerate the minor movement common to sheeted and composite walls, dramatically reducing the risk of surface cracking. It can be applied by standard trowelling methods or by spray, and a variety of decorative finishes can be achieved depending on how it is floated or sponged.Where to use itSuitable for indoor and outdoor use over an unusually wide range of substrates: FC sheet and blueboard, concrete and blockwork, sound painted surfaces (alkali stable and water resistant), existing render, AAC panels and blocks, and EPS foam panels. It is the go-to finishing render where substrate movement or mixed materials would defeat a rigid render.How to useEnsure the substrate is clean, sound and free of dust, oil and loose coatings; prime where the system requires. Mix the powder with clean water to a smooth, lump-free consistency and apply by steel trowel or spray at 2-10mm thickness. Rule off, allow the render to firm, then float, sponge or texture to the desired finish. A 20kg bag covers approximately 6.5m² at 2mm or 2.6m² at 5mm thickness. Clean tools with water before the render sets.Important notesStay within the 2-10mm application range per coat. Avoid rendering in extreme heat, wind or imminent rain, and protect the fresh surface from rapid drying. Painted substrates must be firmly bonded, alkali-stable and water resistant.Specifications
Size
20kg bag
Colour
Grey
Coverage
6.5m² at 2mm or 2.6m² at 5mm per bag
Application thickness
2-10mm
Reinforcement
Fibre-reinforced, polymer modified
SafetyCement-based powder — the wet mix is alkaline and dust can irritate airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in ventilation and wash skin after contact. Refer to the Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Render Joint & Patch is a high-performance, two-in-one compound for rendering projects: it joints fibre cement sheet and blueboard before render is applied, and it patches cracks and holes in existing rendered surfaces up to 5mm deep or wide. Supplied premixed in a light grey colour that blends into most render systems, it takes the fuss out of preparation work — one pail handles both the sheet joints and the surface defects before your finishing coat goes on. The 4L size is perfect for repairs and smaller rendering jobs.Where to use itOn interior and exterior walls. As a jointing compound, use it over blueboard and fibre cement sheet prior to rendering. As a patching compound, use it over sound existing render to fill hairline cracks, chips, divots and small holes before re-coating or painting.How to useSurfaces must be clean, dry, sound and free of dust, loose render and contaminants. Stir the pail, then trowel the compound firmly over sheet joints (embedding tape where the sheet system requires) or press it into cracks and holes, striking off flush with the surrounding surface. Feather edges smooth with a trowel — the Dunlop Gauging Trowel gives a professional finish. Allow to dry fully before applying render, texture or paint, and wash tools in water straight after use.Important notesMaximum patch depth or width is 5mm — build deeper repairs in stages or use a repair mortar. Drying time lengthens in cold or humid conditions. Not intended for structural crack repair or designed movement joints.Specifications
Size
4L pail
Colour
Light Grey
Patch capacity
Cracks and holes up to 5mm (depth or width)
Location
Indoor and outdoor walls
SafetyWater-based compound — wear gloves and safety glasses, avoid skin and eye contact and wash off with water. Keep the pail sealed and out of reach of children, and read the Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Render Joint & Patch in the 10L trade pail is a high-performance combination product that covers two essential preparation steps in one: jointing fibre cement sheet and blueboard ahead of rendering, and patching cracks and holes up to 5mm in existing rendered walls. Premixed to a smooth, light grey consistency, it goes straight from pail to trowel with no mixing, keeping preparation fast and consistent across large jobs. The 10L size is the economical choice for renderers and builders working across full elevations or multiple rooms.Where to use itIndoors and outdoors on walls. Use as a jointing compound over blueboard and fibre cement sheeting before render systems are applied, and as a patching compound over sound existing render to make good cracks, holes and surface defects up to 5mm deep or wide before re-rendering, texture coating or painting.How to usePrepare a clean, dry, sound surface free of dust, loose material and contaminants. Trowel the compound firmly across sheet joints, embedding jointing tape where required by the sheet manufacturer, and feather the edges flush. For patching, press the compound into the defect, strike off level and smooth the surface — the Dunlop Gauging Trowel helps achieve a professional finish. Allow to dry completely before over-coating, and clean tools with water while the product is still wet.Important notesRepairs deeper or wider than 5mm need staged applications or a dedicated repair mortar. Cold, damp or humid weather extends drying times. Do not use across designed movement joints — finish those with a flexible sealant.Specifications
Size
10L pail
Colour
Light Grey
Patch capacity
Cracks and holes up to 5mm (depth or width)
Location
Indoor and outdoor walls
SafetyWater-based product. Wear gloves and eye protection during use, avoid prolonged skin contact and wash exposed skin with water. Store sealed, keep away from children and consult the Safety Data Sheet before application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible FC Jointing Compound in the 8kg trade pail is a premixed, flexible jointing compound for fibre cement sheet and blueboard, formulated to prepare sheet joints before decorative coatings, texture finishes or render go on. Ready to use straight from the container, it removes mixing from the workflow entirely and keeps a consistent, workable body from the first trowel-load to the last. Its flexible acrylic formulation moves with the substrate to resist joint cracking, while strong adhesion keys the compound firmly to the sheet surface.Where to use itFor jointing fibre cement sheeting and blueboard on interior and exterior walls — cladding, facades, garage conversions, extensions and commercial sheeted walls — prior to painting, texture coating or rendering. The larger pail suits whole-wall and multi-room jobs where a 3kg pack would run short.How to useCheck that sheets are rigidly fixed and joints are clean, dry and dust-free. Apply the compound over each joint with a trowel or broad knife, embedding jointing tape where the sheet manufacturer requires it, then finish with a band approximately 75mm wide and 1mm thick, feathered smooth at the edges. Allow to dry completely before over-coating. Wet compound cleans off tools with water. Coverage is approximately 7 lineal metres per kilogram at 75mm width and 1mm thickness, so an 8kg pail joints in the order of 55 lineal metres.Important notesDesigned movement joints should be finished with a flexible sealant rather than jointing compound. Drying slows in cold or humid weather. Keep the lid sealed between uses and do not thin the product with water.Specifications
Size
8kg pail
Colour
Grey
Coverage
Approx. 7Lm per kg (75mm wide at 1mm thick)
Location
Indoor and outdoor walls
SafetyWater-based acrylic product. Wear gloves and eye protection during application, avoid prolonged skin contact and wash with water after use. Store sealed in a cool place away from children and refer to the Safety Data Sheet before starting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ready-to-Go Render is a premixed white render supplied in a resealable pail, ready to trowel straight onto the wall with no mixing, no dust and no wasted powder. Its easy trowel-and-float formulation makes it one of the most approachable renders for first-time renderers, while still giving experienced applicators a smooth, workable body. Applied at 1-5mm, it delivers a clean, uniform finish over a wide variety of common wall surfaces inside and out.Where to use itSuitable for indoor and outdoor projects over AAC panels and blocks, blueboard, brickwork, concrete walls and sound painted surfaces. Ideal for feature walls, fence walls, garden walls, patching over dated finishes and giving tired masonry a fresh, rendered look.How to useMake sure the surface is clean, sound and free of dust, oil and loose or flaking material; prime porous or painted surfaces as recommended. Stir the pail, then apply the render with a steel trowel to a thickness of 1-5mm, working in manageable sections. Rule off and finish with a float or sponge float once the render has firmed — the Dunlop Sponge Float gives a superior finish. For a higher build over uneven walls, first apply Dunlop Multipurpose Acrylic Render as a base coat and use Ready-to-Go Render as the finishing coat. Tools wash up in water.Important notesKeep within the 1-5mm application range per coat. Avoid rendering in direct hot sun, strong wind or when rain is expected; cold and humid conditions extend drying times. Reseal the pail to keep unused render workable.Specifications
Size
16kg pail
Colour
White
Coverage
Approx. 6m² at 1mm or 2m² at 3mm per 16kg
Application thickness
1-5mm
SafetyWater-based premixed render. Wear gloves and safety glasses, avoid skin and eye contact, and wash with water after use. Keep out of reach of children and refer to the Safety Data Sheet for detailed handling information.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible FC Jointing Compound is a premixed, flexible compound for jointing fibre cement sheet and blueboard before decorative coatings are applied. Because it comes ready to use straight from the pail, there is no on-site mixing, no powder mess and no guesswork about water ratios — simply open, stir and trowel. The flexible formulation accommodates the minor movement typical of sheeted walls, while its excellent adhesion delivers a reliable, crack-resistant joint. The compact 3kg pail is ideal for smaller sheeting jobs and repairs.Where to use itUse on interior and exterior walls to finish joints between fibre cement sheets and blueboard prior to painting, texture coating or rendering. It is the recommended first step in preparing sheeted facades, extensions and infill panels for a decorative finish.How to useEnsure sheets are securely fixed and joints are clean, dry and free of dust. Where the sheet system requires it, embed jointing tape in a first application of compound. Apply the compound over the joint with a trowel or broad knife in a band roughly 75mm wide and about 1mm thick, feathering the edges smooth into the sheet face. Allow to dry fully before over-coating with paint, texture or render. Tools clean up with water while the compound is wet. Coverage is approximately 7 lineal metres per kilogram at a 75mm width and 1mm thickness — around 21 lineal metres from this 3kg pail.Important notesNot a structural adhesive or gap filler for moving joints wider than the system allows — use a flexible sealant at designed movement joints. Cold or humid conditions extend drying time. Reseal the pail after use to keep the remainder workable.Specifications
Size
3kg pail
Colour
Grey
Coverage
Approx. 7Lm per kg (75mm wide at 1mm thick)
Location
Indoor and outdoor walls
SafetyWater-based acrylic compound. Wear gloves and safety glasses, avoid skin and eye contact, and keep away from children. Wash hands and tools with water after use, and consult the Safety Data Sheet for full handling advice.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible Coloured Grout in the trade-size 15kg bag is built for big tiling jobs - whole houses, commercial floors and multi-room renovations. It is the same flexible, smooth-finish formula tilers rely on, with a stronger colour system for rich, even grout lines and Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth in wet areas. The grout works easily, ensures flush joints and leaves no pin holes.Where to use itSuitable for walls and floors, indoors and outdoors, over ceramic, porcelain, marble, granite and mosaic tiles. With a working range of 1mm to 8mm joints it handles fine wall tiling through to wide-format floor tiles, and the grey tones (Misty Grey and Slate Grey) are popular choices for high-traffic floors where joints need to hide everyday wear.How to usePrepare clean, dry joints raked free of adhesive. Mix with clean water to a smooth paste - or with Dunlop Primer & Additive to boost colour, flexibility, adhesion and stain resistance. Apply diagonally with a rubber grout float, pack joints full, remove excess, then sponge the tiles clean once the grout firms and polish off haze. Initial set is around 24 hours, showers can be wet after 3 days, and full cure is reached after 7 days.Important notesInclude about 15% wastage in quantity estimates. Mix batches with consistent water content to avoid colour variation across large floors.Specifications
Joint width
1 - 8mm
Coverage guide
Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyCement-based product - alkaline when wet and may irritate skin and eyes. Wear gloves and eye protection, avoid inhaling dust when emptying and mixing the bag, and wash after use. Keep out of reach of children; see the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ultra-White Grout is a non-sanded, flexible cement-based grout that delivers a super smooth, brilliantly white finish between wall and floor tiles. Formulated with Grout Shield anti-mould and anti-bacteria technology, it actively resists the growth of mould and bacteria so joints stay looking cleaner for longer. The cured grout is water repellent, resists dirt pick-up and is easy to wipe clean, making it a favourite for bright, fresh bathrooms and kitchens.Where to use itUse Ultra-White Grout on walls and floors, indoors and outdoors. It is suited to ceramic, porcelain, marble, granite and mosaic tiles, and is designed for narrow tile joints between 1mm and 4mm wide where a fine, non-sanded finish is wanted.How to useEnsure joints are clean, dry and free of dust or adhesive residue. Mix the powder with clean water to a smooth, lump-free paste, then work the grout firmly into the joints on the diagonal using a rubber grout float or squeegee. Remove the excess as you go, then clean the tile faces with a lightly damp sponge once the grout has firmed. Polish off any remaining haze with a soft, dry cloth. Allow the grout to cure fully before exposing wet areas such as showers to water.Important notesCoverage varies with tile size, joint width and joint depth, and a wastage allowance of around 15% should be included when estimating. For wide joints over 4mm choose a sanded or wide-joint grout instead. Pair with Dunlop Grout Sealer for extra stain protection.Specifications
Joint width
1 - 4mm
Coverage guide
Approx. 6.7m² for 300 x 300 x 5mm tiles at 3mm joints (incl. 15% wastage)
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyCement-based product - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing dust when mixing, and wash hands after use. Keep out of reach of children and refer to the Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ultra-White Grout in the 5kg pack is a non-sanded, flexible grout that produces a super smooth, super white finish across larger tiling jobs. It contains Grout Shield anti-mould and anti-bacteria technology to resist mould and bacteria growth, and the cured joint is water repellent and easy to clean, helping white joints stay bright in busy bathrooms, laundries and kitchens.Where to use itSuitable for tile joints on walls and floors, indoors and outdoors. Use it with ceramic, porcelain, marble, granite and mosaic tiles wherever joints are between 1mm and 4mm wide. The 5kg pack size suits full bathroom renovations, splashback runs and floor areas where a 1.5kg pack would run short.How to usePrepare joints so they are clean, dry and raked free of adhesive. Mix the powder with clean water to a smooth, creamy paste and let it stand briefly before remixing. Apply diagonally across the joints with a rubber grout float, pressing the grout in fully and striking off the excess. Once firm, sponge the tile faces clean with minimal water, then buff away the haze with a dry cloth. Keep showers dry until the grout has cured.Important notesEstimate quantities from tile size, joint width and depth and allow roughly 15% extra for wastage. Not intended for joints wider than 4mm. Sealing with Dunlop Grout Sealer after curing improves long-term stain resistance.Specifications
Joint width
1 - 4mm
Coverage guide
Approx. 13.3m² for 300 x 300 x 5mm tiles at 1.5mm joints (incl. 15% wastage)
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid inhaling dust while mixing, and wash thoroughly after handling. Keep out of reach of children and consult the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible Coloured Grout in the 5kg pack brings the same smooth finish and strong, consistent colour as the smaller pack, in a size suited to whole bathrooms, kitchens and floor areas. The formula is flexible and easy to work, ensures flush joints with no pin holes, and contains Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth so grout lines stay looking better for longer.Where to use itGrout walls and floors indoors and outdoors with ceramic, porcelain, marble, granite and mosaic tiles. Joints from 1mm to 8mm are covered, making it suitable for everything from fine mosaic work to wide-format floor tiles. In swimming pools, use White 200 mixed with Dunlop Primer & Additive.How to useRake joints clear of adhesive and ensure they are clean and dry. Mix the powder with clean water to a smooth, lump-free paste - or gauge with Dunlop Primer & Additive for enhanced colour, adhesion, abrasion and stain resistance. Work the grout diagonally into the joints with a rubber float, strike off the excess, then sponge clean once the grout firms and buff away residual haze. Initial set is about 24 hours, showers can get wet after 3 days, sealing is possible after 3 days and full cure takes 7 days.Important notesAllow roughly 15% wastage when estimating coverage from tile size, joint width and depth. Keep mixing water consistent between batches for uniform colour.Specifications
Joint width
1 - 8mm
Coverage guide
Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid dust when mixing, and wash hands after use. Keep out of reach of children and consult the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Feather Finish is a cement-based smoothing compound that skims internal floors to a super-smooth, permanent finish before floor coverings are installed. Powered by ARDEX Ardit technology, it trowels out to a true feather edge and sets so fast that coverings can be applied from just 15 minutes after placement - and it needs no primer on most surfaces, saving a whole step.Where to use itFor indoor use over concrete, existing tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. It is ideal for filling grout joints when covering old tiles with vinyl, smoothing trowel marks in levellers, and taking out minor imperfections before vinyl, carpet or ceramic tiles.How to useEnsure the floor is clean, sound and free of dust, grease and loose material. Mix the powder with clean water to a smooth, creamy paste and apply with a flat steel trowel, working from a feather edge up to 3mm thick. Tight second coats can be applied as the first firms. Any ridges can be shaved or lightly sanded once set for a flawless surface.Important notesIndoor use only and must be covered by a floor covering. Mix small batches to suit the rapid set. No primer is required over common substrates - check the datasheet for unusual surfaces.Specifications
Size
3.5kg bag
Coverage
Approx. 12m² over concrete or 24.5m² over sheet timber (skimcoat)
Thickness
Feather edge to 3mm
Substrates
Concrete, tiles, sheet timber, Dunlop floor levellers
Walk-on time
15-30 minutes; coverings from 15 minutes
SafetyCement powders can irritate eyes, skin and lungs. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated, avoid prolonged contact with the wet compound and wash hands after use. Store out of reach of children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications
Size
8kg bag
Coverage
Approx. 27m² over concrete or 55m² over sheet timber (skimcoat)
Thickness
Feather edge to 3mm
Substrates
Concrete, tiles, sheet timber, Dunlop floor levellers
Walk-on time
15-30 minutes; coverings from 15 minutes
SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Level-Flex Timber Floor Leveller is a high performance, partially self-smoothing latex levelling screed developed specifically for timber floors. Supplied as a complete two-part kit in a handy pail, it combines a cement-based powder with a flexible latex liquid to deliver the adhesion, flexibility and water resistance needed when levelling over floors that move more than concrete does.Where to use itDesigned for indoor use over timber and concrete subfloors, it creates a smooth, flat surface ready for ceramic tiles, carpet or vinyl. It is a popular choice for renovating older homes with uneven timber floorboards or sheet flooring before new coverings are installed.How to useSand and prime timber floors first, and prime porous concrete with a plush broom application. Blend the latex liquid with the powder using a low-speed paddle mixer until smooth, then pour and spread with a trowel, allowing the screed to flow out and self-smooth. The floor is walkable in about 3 hours; lay ceramic tiles after roughly 12 hours (3mm screed), carpet after 24 hours and vinyl after 48 hours.Important notesIndoor use only, and the leveller must be covered by a finished floor covering. Timber must be sound, rigid and well fixed before levelling. Low odour formula makes it comfortable to use in occupied homes.Specifications
Size
15.9kg kit (powder plus latex liquid)
Coverage
Approx. 7m² at 1mm or 2.3m² at 3mm per kit
Thickness
Feather edge to approx. 12mm (thicker with aggregate)
Substrates
Timber and concrete
Walk-on time
3 hours
SafetyWear gloves, safety glasses and a P2 dust mask when handling the cement powder, and keep the room ventilated while mixing. Avoid skin and eye contact with the wet mix, wash after use and store the kit away from children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Timber Floor Leveller is a high performance, partially self-smoothing screed for timber floors, built on ARDEX Ardit technology. Unlike traditional two-part latex levellers, it is a convenient single-part formula - just add water - yet still delivers the excellent adhesion, flexibility and water resistance needed to level over timber substrates that flex underfoot.Where to use itFor indoor use over timber and concrete subfloors, creating a smooth, even base before installing ceramic tiles, carpet or vinyl. It is well suited to renovations where old floorboards or sheet flooring need flattening before new coverings are laid.How to useSand and prime all timber floors before application, and prime porous surfaces such as concrete using a plush broom. Mix the powder with clean water using a low-speed paddle mixer until smooth and lump free, then pour, spread with a trowel and let the screed flow out to a level finish. Apply from a feather edge up to 12mm neat, or up to 30mm with the addition of 2-5mm aggregate.Important notesIndoor use only and must be covered with a finished floor covering. Ensure timber floors are rigid and securely fixed before levelling. The no-odour formula suits occupied homes. Check the technical datasheet for covering wait times for your chosen flooring.Specifications
Size
16kg kit
Coverage
Approx. 10m² at 1mm or 3m² at 3mm per kit
Thickness
0-12mm neat; 12-30mm with aggregate
Substrates
Timber and concrete
SafetyThe cement-based powder is alkaline and dusty when dry. Wear gloves, eye protection and a P2 dust mask while mixing, ventilate the work area, avoid contact with skin and eyes, and wash thoroughly after use. Keep away from children and pets.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Floor Leveller is a premium cement-based levelling compound built on the renowned Ardit Technology from ARDEX. It offers superior flow and workability, spreading easily across uneven concrete to create a smooth, even surface before new floor coverings go down. Floors are walkable in around 3 hours and ready for ceramic tiles in the same timeframe, keeping renovation and re-flooring jobs moving quickly.Where to use itUse indoors and outdoors under covered areas over sound concrete floors, ahead of ceramic tiles, carpet or vinyl. It is designed for concrete substrates only and must be protected by a floor covering rather than left exposed to the weather or used as a finished wear surface.How to useEnsure the slab is clean, sound and primed as required. Mix each 20kg bag with approximately 4.5L of clean water using a low-speed paddle mixer until smooth and lump free. Pour and spread with a trowel, letting the compound flow out and level itself. Apply from a thin skim up to 25mm in one pass, adding 2-5mm aggregate for deeper fills.Important notesNot suitable for driveways or areas subject to vehicular traffic. Vinyl and carpet can be laid after about 24 hours, while tiles can go down after roughly 3 hours. Refer to the technical datasheet for priming guidance on porous slabs.Specifications
Size
20kg bag
Coverage
Approx. 12m² at 1mm or 4m² at 3mm per bag
Thickness
1-25mm per application
Substrates
Concrete
Walk-on time
3 hours (tiles 3 hours; vinyl and carpet 24 hours)
SafetyContains cement, which is alkaline when wet. Wear gloves, eye protection and a P2 dust mask while mixing, ensure good ventilation, avoid skin contact and rinse promptly if the mix touches skin or eyes. Store away from children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Multipurpose Floor Leveller is a cement-based levelling compound from Dunlop Trade (ARDEX Australia) that mixes with water into a smooth, free-flowing material for evening out rough or uneven concrete floors. It flows into low spots and finds its own level, leaving a flat base that is ready for foot traffic in around 2 hours and ready for tiles in about 4 hours, making it a dependable first step before laying new floor coverings such as carpet, vinyl or ceramic tiles.Where to use itSuitable for indoor and outdoor use over sound concrete floors, including living areas, kitchens, laundries and covered patios. It can also be used to form ramps or for bulk filling. It is designed for concrete substrates only and must always be covered by a finished floor covering.How to usePrepare the slab so it is clean, sound and free of dust or contaminants, and prime porous surfaces. Slowly add the powder to clean water while mixing with a low-speed paddle mixer for 2-3 minutes until lump free. Pour onto the floor, spread with a trowel and allow it to self-smooth. Apply up to 25mm in one application, adding 2-5mm aggregate for beds thicker than about 10mm.Important notesNot suitable for driveways or areas with vehicle traffic, and it cannot be left exposed as a wear surface. Sand can be added to create a trowelable screed for ramping. Always follow the technical datasheet for priming and mixing details.Specifications
Size
15kg bag
Coverage
Approx. 1.6kg/m² per mm (about 9m² at 1mm per bag)
Thickness
Up to 25mm per application
Substrates
Concrete
Walk-on time
2 hours (tiles after 4 hours)
SafetyCement-based powders are alkaline and can irritate skin, eyes and airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in a ventilated area, wash skin after use and keep out of reach of children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Get crisp, professional paint lines with Wagner Mask-It. This painter’s masking tape is designed to seal neatly along the edge, reduce paint bleed, and remove cleanly when the job is done. Ideal for walls, trim, skirting boards, window frames, and any detail work where a sharp finish matters.
Key Benefits
Clean paint edges that help minimise bleed on most interior surfaces.
Easy application with a smooth unwind and hand tearable backing.
Clean removal when used as directed on properly prepared surfaces.
Works with brushes, rollers, and spray for DIY and trade jobs.
Perfect For
Cutting in around ceilings, cornices, and trims
Protecting hardware, switches, and fittings
Two tone feature walls and accent colours
Masking glass, tiles, and metal fixtures during repainting
Surface Compatibility
Use on properly prepared, fully cured interior paint, primed timber, metal, glass, and most smooth surfaces. Always test in an inconspicuous area first.
How To Use
Prep the surface: Ensure it is dry, dust free, and fully cured.
Apply the tape: Press down firmly along the edge with a putty knife or fingernail to seal.
Paint: Roll or brush away from the tape edge for best results.
Remove: Peel back slowly at a 45 degree angle while paint is still slightly tacky, unless your coating specifies otherwise.
Pro Tips
Burnish the tape edge lightly to improve the seal on textured areas.
Apply light coats near the edge. Heavy wet coats can overwhelm any mask.
For long runs, overlap tape pieces by a few millimetres and press the overlap firmly.
Good To Know
Suitable for indoor projects and general decorating.
Store in a cool, dry place away from direct sunlight to maintain performance.
Available in popular widths to suit trim work and broad masking.
Frequently Asked Questions
Will it pull off fresh paint?Only apply to fully cured paint. Cure times vary by product and conditions. When in doubt, allow extra time and test first.
Does it work on lightly textured walls?Yes, on many light textures, but press down firmly along the edge and use lighter coats near the tape line.
Can I use it with spray equipment?Yes. Apply, seal the edge, and use controlled passes. Avoid flooding the tape line.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Achieve smooth, long lasting plasterboard joints with Gyprock CSR FibaFuse Joint Tape. This premium paperless tape bonds beautifully with both setting and drying compounds to reinforce seams, reduce the risk of cracks, and deliver a professional finish on walls and ceilings.
Why choose FibaFuse
Stronger joints thanks to an open fiber structure that integrates with joint compound for excellent reinforcement.
Smooth finishing with feathered edges that sand and paint cleanly.
No bubbling when properly embedded in compound for a flat, reliable seam.
Works with most compounds including setting type and ready mixed formulas.
Ideal for pros and DIY on new installs, repairs, and patchwork.
Best for
Joining plasterboard sheets on walls and ceilings
Butt and tapered edge joints
Repairs to cracked or previously patched seams
High traffic areas that need extra durability
How to use
Prep Ensure surfaces are clean, dry, and free of dust. Lightly bevel cut edges if required.
Bed coat Apply an even layer of joint compound over the seam at least the width of the tape.
Embed Place the FibaFuse tape into the wet compound and press firmly with a taping knife to remove air pockets.
Cover Apply a thin coat over the tape to fully conceal the mesh. Allow to dry or set as per the compound directions.
Build Apply one or two wider coats, feathering the edges for a flat transition. Let each coat dry before the next.
Finish Lightly sand, prime, and paint.
Pro tips
Keep knife pressure firm during embedding to avoid bubbles.
Use a wider knife for second and third coats to reduce sanding.
Prime before painting for a consistent sheen across joints and boards.
Product details
Brand
Gyprock CSR
Type
Paperless joint tape for plasterboard seams
Compatibility
Setting and ready mixed joint compounds
Applications
Walls, ceilings, butt joints, tapered edges, repairs
Frequently asked questions
Do I need to pre soak the tapeNo. Embed the tape directly into wet compound.
Can I use it with ready mixed compoundYes. It works with ready mixed and with setting type compounds. Follow the compound instructions for drying or set times.
Will it show through paintNot when properly covered with compound, sanded smooth, and primed before painting.
Good to know
Store flat and dry to maintain tape integrity.
Always wear appropriate PPE when sanding joint compound.
Glues Australia helps you get a strong, professional finish without the fuss. Why buy new when you can fix
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
High-Grade Neutral Cure Silicone
A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots.
Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying.
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour, so can be used in any environment without discomfort.
Easy to clean once applied, as it resists moisture, hot cooking oils, and steam.
Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch.
Temperature resistance: approximately -60°C to +150°C.
25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying.
Where can this product be used?
Showers and sinks
Metal, copper, and brass fittings
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper, and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine.
Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe.
Remove tape before the sealant skins. Clean tools immediately with mineral turpentine.
Avoid smearing on surrounding surfaces.
The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup.
When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish, complete painting prior to using the sealant as it cannot be painted over.
Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish.
Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures.
Safety Tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and Re-Use
Store in cool dry conditions, below 30°C.
The sealant should be used within 6 months after opening.
After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity.
For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge.
If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned.
Why you’ll love it
Exterior-grade flexibility: absorbs movement and vibration without cracking.
Non-shrink & non-sink: holds profile and edge detail after cure.
Won’t fall out: engineered adhesion for long-term durability.
Ready to use: straight from the tub — no mixing, no mess, no waste.
Paintable: achieves a seamless, colour-matched finish once dry.
No VOCs: low odour, solvent-free formula.
Interior / Exterior: versatile enough for both.
Proudly Australian: made and owned in Australia.
Where it works
Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates:
Timber: decks, window frames, trims, fascia, general carpentry repairs.
Masonry: brick, block, render and patching mortar-like defects.
Plasterboard: exterior-exposed linings under cover and general patching.
Metals & gutters: non-structural filling and profiling (clean, sound, free of rust).
Around pipes & penetrations: neat, gap-free finishing before painting.
Glass & surrounds: edge repairs and feathering prior to topcoating.
Ideal projects
Rebuilding weathered or rotten timber edges before repainting.
Filling cracks and surface imperfections in rendered walls.
Profiling and feathering joints and transitions for a paint-ready finish.
General exterior maintenance where a flexible, paintable filler is essential.
Directions
Surface Preparation
Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound.
Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required.
For best mechanical key, lightly abrade glossy surfaces and remove dust.
Application
Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use.
Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate.
Build up in thin layers for deep repairs, allowing each layer to firm before adding the next.
For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing.
Finishing & Painting
Allow to dry fully. Dry time varies with film thickness, temperature and humidity.
Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat.
Use quality exterior paints for weather-exposed areas.
Clean-Up & Storage
Clean tools and splashes with water while wet.
Reseal immediately after use to minimise skinning and reduce waste.
Store upright with lid sealed. Do not allow contents to dry out.
Good to know
Formulation is unaffected by normal temperature swings and resists cracking with vibration.
Designed for exterior flexibility yet also suitable for interior touch-ups.
For best results on deep voids, fill in multiple light applications rather than one heavy pass.
Specifications
Brand
Earl’s
Product
MulTflex® Exterior Flexible Filler
Type
Single-pack, ready-to-use flexible filler & adhesive
Use
Interior / Exterior
Paintable
Yes, once fully dry
VOC Content
No VOCs (as supplied)
Shrink / Sink
Non-shrinking, non-sinking
Flexibility
Resists cracking with vibration and movement
Clean-Up
Water (while wet)
Substrates
Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass
Finish
Satin-smooth when tooled with a wet knife or brush
Packaging
Ready-to-use tub
Country of Origin
100% Australian made & owned
Limitations
Do not apply to unsound, dusty or actively corroding surfaces without proper preparation.
Dry and cure times depend on depth and conditions; confirm dryness before painting.
Not intended for structural repairs.
Pro Tips
Feather edges wide for invisible paint blending on weathered timber and render.
Keep a small cup of clean water nearby to maintain a smooth final pass.
Deep cavities: bridge with successive thin layers for the most stable result.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys SolarFlex
Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical.
Features
Superior weather protection
Long-lasting flexibility
No primer required before painting
Watertight seal with a 10-year guarantee*
Adhesion to wet or damp surfaces
Non-bubbling
Better curing and extrudability (>5°C) with no slump
Paintable with water-based paints after product skins in 60 to 90 minutes
Low VOC**
Where can this product be used?
Skylights
Walls
Patios
Floors
Fencing
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic tiles
Fibreglass
Most plastics*
*Not suitable on polyethylene, polypropylene, or Teflon.
Application Instructions
Ensure substrates are clean and free of oil, grease, or loose particles.
Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun.
Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint.
For neat joints, use masking tape on both sides of the joint and remove it before skinning.
Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information.
Limitations
Not suitable on polyethylene, polypropylene, or Teflon.
Cure excess product before disposal.
Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ready to use, hard drying acrylic putty filler
Ideal for repairing cracked, broken or uneven surfaces
30 minute fast drying time
Includes bonus applicator
Suitable for fibrous cement, brick, plaster and wood surface repairs
available in 500gm/1.5kg
Not suitable for wet areas or where structural movement occurs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates.
Key Features
Bonds well to a wide variety of substrates without surface pre-treatment
Adheres to damp concrete and other porous materials
Compatible with most construction materials, including EPS/XPS and building wraps
Excellent mechanical strength and weathering resistance
Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified
Ideal for bonding and sealing in indoor and outdoor environments
Where to Use
Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing:
Concrete and masonry
Wood and timber components
Ceramic, stone, and tiles
Metal surfaces
Glass and plastic materials such as PVC, PA, PET, and EPS/XPS
Applications
Adhesive for bonding construction components
Sealant for vertical and horizontal joints
Repairs, renovations, and installations in building and civil works
Technical Information
Composition
Silane-terminated polymer
Density
~1.40 kg/L (ISO 1183-1)
Shore A Hardness
~36 (after 28 days)
Tensile Strength
~1.5 N/mm² (ISO 37)
Elastic Recovery
~75 % (ISO 7389)
Service Temperature
−50 °C to +80 °C
Curing Rate
~3 mm per 24 h (at 23 °C / 50 % r.h.)
Skinning Time
~35 minutes (at 23 °C / 50 % r.h.)
Colour Options
Available in White, Concrete Grey, and Black.
Packaging
290 ml cartridge | 12 cartridges per box
Storage & Shelf Life
Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date.
Certifications
CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM)
GEV-EMICODE EC 1PLUS (Very Low Emissions)
LEED v4 EQc 2 Low-Emitting Materials compliant
French VOC Regulation Class A+
Why Choose Sikaflex®-111 Stick & Seal
This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates.
Key Features
Bonds well to a wide variety of substrates without surface pre-treatment
Adheres to damp concrete and other porous materials
Compatible with most construction materials, including EPS/XPS and building wraps
Excellent mechanical strength and weathering resistance
Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified
Ideal for bonding and sealing in indoor and outdoor environments
Where to Use
Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing:
Concrete and masonry
Wood and timber components
Ceramic, stone, and tiles
Metal surfaces
Glass and plastic materials such as PVC, PA, PET, and EPS/XPS
Applications
Adhesive for bonding construction components
Sealant for vertical and horizontal joints
Repairs, renovations, and installations in building and civil works
Technical Information
Composition
Silane-terminated polymer
Density
~1.40 kg/L (ISO 1183-1)
Shore A Hardness
~36 (after 28 days)
Tensile Strength
~1.5 N/mm² (ISO 37)
Elastic Recovery
~75 % (ISO 7389)
Service Temperature
−50 °C to +80 °C
Curing Rate
~3 mm per 24 h (at 23 °C / 50 % r.h.)
Skinning Time
~35 minutes (at 23 °C / 50 % r.h.)
Colour Options
Available in White, Concrete Grey, and Black.
Packaging
290 ml cartridge | 12 cartridges per box
Storage & Shelf Life
Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date.
Certifications
CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM)
GEV-EMICODE EC 1PLUS (Very Low Emissions)
LEED v4 EQc 2 Low-Emitting Materials compliant
French VOC Regulation Class A+
Why Choose Sikaflex®-111 Stick & Seal
This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER-101 | FINE SURFACE FILLER
Premium, fine surface filler
Very fine consistency for fine surface filling
Application thickness up to 3mm per layer
Fast drying and easy to sand
USE
Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc.
Smooth finish
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
COLOUR: White
Appearance / Colour White paste
Packaging 500 ml plastic tube
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion.
Density ~ 1.100 kg/l
Solid Content
~ 55%
Grading Dmax : 0.12 mm
Layer Thickness 3 mm max.
Application Details
Consumption
This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika®
Filler-101 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application
Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-101 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: ~ 2 hours
Paintability: ~ 4 hours
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*.
Provides superior water resistance, mould and soap scum resistance
White For Life – Always looks like new*
Resists yellowing, staining and blackening*
Crack resistant
Sand free - resists scratching files
Suitable for indoor wall and floor tiles
Comes in a cartridge for minimum wastage
Where can this product be used?
Bathrooms
Showers (walls only)
Toilets
Laundries
Kitchens
What materials is this product suitable for?
Ceramic tiles
Porcelain tiles
Stone tiles
Most other tiles
Please contact your store to confirm avaliability, as some stores may have a limited range.
How to Use
Preparation
For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult.
Application
Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time.
Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint.
Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets.
Allow grout to firm up in joints for approx 20 min (longer in colder conditions).
Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints.
Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks.
overage
1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
Limitations:
Not for areas frequently immersed in water eg. Shower floors.
Allow to dry for 3 days before exposing grout to water on shower walls.
Handy tips
If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas.
*To maintain whiteness and long term stain & mould resistance:
Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard.
Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners.
Areas subject to high foot traffic will require frequent cleaning.
Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes.
Coverage guide
1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
Clean Up
Clean up tools with water before product hardens.
Uncured product may be removed with water.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens.
Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
Mould resistant
Precision application for the best finish
Where can this product be used?
Showers
Baths
Spas
Sinks
Metal, copper and brass plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Powder coated aluminium
Aluminium
Plastic laminates
Rubber
Glass
Stainless steel
Concrete
Size
100g Aerosol can
Technology
Neutral Cure Silicone
Use
Interior
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
1. Throughly clean and dry surface from oil, dirt and grease with mineral turps.
2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
4. Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Sealant is not paintable.Complete painting 7days prior to applying sealant.
• Not for aquariums or contact with food, eating utensils or drinking water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Fibreglass Fix Repair Kit is a complete kit containing polyester resin, a hardener and fibreglass mat, for repairs to fibreglass and a variety of other surfaces.
Where can this product be used?
Boat repairs including hull repairs
Surfboard / Surfski repairs
Automotive repairs
Repairing a leaky gutter
Patching downpipes
Patching metal roofs or grass catchers
Not approved for contact with drinking water
What materials is this product suitable for?
Fibreglass
Plywood
Metal
Fibro Sheeting
Most Plastics
How to use this product
Wear rubber or plastic gloves when handling fibreglass
Surface Preparation Surfaces should be clean and dry and free from paint, grease and rust. Cut the fibreglass mat to shape, allowing approximately 3cm overlap all round. Tease out the fibres along the edge of the mat to give a feathered edge.
For wide holes, glue a piece of cardboard to the back of the hole to form a base.
Mixing: For each tablespoon of resin, squeeze 5 drops of hardener from the small tube and mix together thoroughly.
Do not prepare the mixture until required as only a limited time (20 minutes at 20°C) is available before the product gels.
Application Position the mat and apply resin/hardener mixture with a clean, dry brush. Be sure to impregnate the mat completely, working out all air bubbles. Add more mat and resin/hardener mixture to build up or contour the patch as required.
Finishing When the patch has completely hardened, (approximately 1-2 hours, depending on the temperature), it can be sanded to a smooth finish. Fill imperfections with more resin. Paint if required.
Clean up product with Solvent Acetone before it cures
Handy tips
At higher temperatures, the working time decreases.
Can only be tinted with iron oxide or other dry pigments .which must be mixed in very thoroughly.
Surfaces to be joined should be clean and dry.
If recommended amounts of hardener are not used, cure time will vary or an incomplete cure may result.
A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol).
In large amounts, heat can be generated during cure. Care should be taken on heat-sensitive surfaces with large amounts.
Use recommended levels of hardener and resin; variation may result in incomplete cure and variations in cure time.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Features
Non-corrosive
Weather resistant – resistant to water, weather or marine growth
Rapid setting
Impact resistant – can take knocks
Sandable – can be sanded after 1-2 hours
Can be painted over
Extended working time – up to 20 minutes at 20°C
Dries Opaque
Heat resistant to 100°C
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants.
Features
Superior strength & instant grab
No primer required
Watertight seal with a 10-year guarantee*
Can be applied to wet or damp surfaces with excellent adhesion
Non-bubbling
Better curing and extrudability (>5°C)
Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes
Sandable
Low VOC**
Long-lasting flexibility
Fast curing
No slump
Trafficable
Potable water approved AS/NZS4020 (Area to volume ratios
**Meets GBCA limits for general purpose and architectural sealants.
Where can this product be used?
Skylights
Walls
Patios
Floors
Fencing
Windows
Expanding joints in concrete
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic tiles
Fibreglass
Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.)
Ensure substrates are clean and free of oil, grease or loose particles.
Cut seal and nozzle and fit to cartridge, then place in caulking gun.
Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For neat joints, use masking tape on both sides of the joint and remove before skinning.
Tool with a soapy solution before skinning occurs.
For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information.
Limitations:
Not suitable on polyethylene, polypropylene or Teflon.
Not for permanent water immersion or below water-line use.
In dry conditions, surfaces can be misted with water to speed up cure.
Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one.
Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics*
Features
As a Construction Adhesive
High strength bond
Water and weather resistant
Use on multiple surfaces
As a Sealant
Provides a lasting waterproof seal
Can be used on all indoor and outdoor surfaces
Easily paintable with 2 coats of water-based paints
As Gap Filler
Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant
Can be used on all indoor and outdoor surfaces
Easily paintable with 2 coats of water-based paints
*Not for polyethylene, polypropylene or Teflon
Where can this product be used?
Use 3 in 1 for sealing, bonding and filling almost any material
Damp or dry, inside or outside
Provides a durable waterproof seal
Provides strong bonds and a perfect paintable finish
What materials is this product suitable for?
Glass
Metals
Timber
Brick
Concrete
Tiles
Most plastics (not for polyethylene, polypropylene or teflon)
How to Use
Adhesive
Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure.
Sealant
Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs.
Gap Filler
Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints.
Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first.
Tips:
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
Larger, heavier items need to be supported until the adhesive cures.
Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Products that level to a clean, smooth surface with minimal tooling, ideal for visible seams and cosmetic repairs. Use filters to refine by chemistry, viscosity and cure profile. Always review the product page and TDS/SDS.
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
![Parfix Gap Filler Flexible Paintable Interior [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
![Monarch Mini Gap Filler [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
![Selleys Wet Area Sealant EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
![Selleys Armour Flex High Performance Adhesive [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125262_5e542168-6518-4fbd-97ab-586ab182d6e9.jpg?v=1754711932&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](//gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Poly Gap Filler Sealant Multipurpose [White]](//gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
![Parfix Gap Filler Flexible Paintable Interior [White]](//gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
![Monarch Mini Gap Filler [Brown]](//gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](//gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
![Selleys Wet Area Sealant EZI Press [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
![Selleys Armour Flex High Performance Adhesive [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125262_5e542168-6518-4fbd-97ab-586ab182d6e9.jpg?v=1754711932&width=645)
