Wood Fillers

Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time."  You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.

Read more less

Colours to suit almost any timberWaxstix are so easy to use and so handy for quick repairs to scratched or damaged timber. Waxstix can be coated and stained. Plus, Waxstix contain no beeswax so they will not leave any white ring marking otherwise known as the "halo effect". For most small scratches, simply rub the stick over the damaged area. For larger, deeper indentations (where TIMBERMATE water-based Woodfiller cannot be used), heat a knife blade with a flame or a soldering iron or stove lighter and fill the damaged area with hot wax. Remove excess wax by rubbing with the smooth side of sandpaper, a piece of cardboard or an old credit card. Use a cotton cloth to buff and remove excess wax.

Read more less

Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.

Read more less

Water-based interior wood filler suitable for all timber types and timber by-products. Once set, the wood filler can be sanded, screwed, and nailed. The wood filler is suitable for filling cracks, holes, end grain, and edges. For exterior use, protect with a suitable exterior grade finish (e.g. paint or stain) Features & Benefits Environmentally friendly Dries quickly Water clean up Easy to use Long shelf-life; if filler hardens just add drops of water & mix Multi-purpose, 4 in 1 uses – fills nails holes, takes stain or paint easily, repairs gouges & chips and crack & edge filler

Read more less

Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming

Read more less

Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.

Read more less

Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned. Why you’ll love it Exterior-grade flexibility: absorbs movement and vibration without cracking. Non-shrink & non-sink: holds profile and edge detail after cure. Won’t fall out: engineered adhesion for long-term durability. Ready to use: straight from the tub — no mixing, no mess, no waste. Paintable: achieves a seamless, colour-matched finish once dry. No VOCs: low odour, solvent-free formula. Interior / Exterior: versatile enough for both. Proudly Australian: made and owned in Australia. Where it works Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates: Timber: decks, window frames, trims, fascia, general carpentry repairs. Masonry: brick, block, render and patching mortar-like defects. Plasterboard: exterior-exposed linings under cover and general patching. Metals & gutters: non-structural filling and profiling (clean, sound, free of rust). Around pipes & penetrations: neat, gap-free finishing before painting. Glass & surrounds: edge repairs and feathering prior to topcoating. Ideal projects Rebuilding weathered or rotten timber edges before repainting. Filling cracks and surface imperfections in rendered walls. Profiling and feathering joints and transitions for a paint-ready finish. General exterior maintenance where a flexible, paintable filler is essential. Directions Surface Preparation Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound. Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required. For best mechanical key, lightly abrade glossy surfaces and remove dust. Application Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use. Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate. Build up in thin layers for deep repairs, allowing each layer to firm before adding the next. For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing. Finishing & Painting Allow to dry fully. Dry time varies with film thickness, temperature and humidity. Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat. Use quality exterior paints for weather-exposed areas. Clean-Up & Storage Clean tools and splashes with water while wet. Reseal immediately after use to minimise skinning and reduce waste. Store upright with lid sealed. Do not allow contents to dry out. Good to know Formulation is unaffected by normal temperature swings and resists cracking with vibration. Designed for exterior flexibility yet also suitable for interior touch-ups. For best results on deep voids, fill in multiple light applications rather than one heavy pass. Specifications Brand Earl’s Product MulTflex® Exterior Flexible Filler Type Single-pack, ready-to-use flexible filler & adhesive Use Interior / Exterior Paintable Yes, once fully dry VOC Content No VOCs (as supplied) Shrink / Sink Non-shrinking, non-sinking Flexibility Resists cracking with vibration and movement Clean-Up Water (while wet) Substrates Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass Finish Satin-smooth when tooled with a wet knife or brush Packaging Ready-to-use tub Country of Origin 100% Australian made & owned Limitations Do not apply to unsound, dusty or actively corroding surfaces without proper preparation. Dry and cure times depend on depth and conditions; confirm dryness before painting. Not intended for structural repairs. Pro Tips Feather edges wide for invisible paint blending on weathered timber and render. Keep a small cup of clean water nearby to maintain a smooth final pass. Deep cavities: bridge with successive thin layers for the most stable result.

Read more less

Cabot's Wood Tone Putty is ideal for filling holes, cracks and blemishes in all interior timber without shrinking. It is easy to apply and sands to a fine, smooth finish. Wood Tone Putty is compatible with water or oil based paints, stains and timber finishes. Areas All interior timber Clean Up Water Product Type Water Based

Read more less

The Timbermate Timber Touch Up Kit gives you a water-based wood filler and a set of wax touch-up crayons in four timber shades, so you can deal with dents, gaps and scratches around the house without sanding back a whole surface. It suits furniture, floors, door and window frames, architraves, staircases and picture frames, and it is simple enough for first-time repairers.About the formulaThe kit pairs two products. Timbermate is a water-based, interior grade wood filler made without acrylic or latex, which is why it resists shrinking, sinking, cracking and falling out of the repair. The pre-mixed colours can also be tinted with any stain or colourant to fine-tune a match. It has an indefinite shelf life, and if it dries out in the tub it can be reconstituted. Waxstix are synthetic wax crayons that contain no beeswax, so repairs accept coatings and avoid the pale ring that beeswax-based products can leave around the edges. Several sticks can be blended to match a colour or to imitate grain.Where to use itIndoors: touch-ups on timber furniture, floors, staircases, architraves, window and door frames and picture frames.Outdoors: not recommended, as this kit is intended for interior use only.Suitable for timber surfaces. The filler can be sanded, stained or painted once dry, and Waxstix repairs can be coated over.How to use itClean the damaged area and make sure it is free of dust and loose material. For gaps, holes and dents, press the woodfiller in with a scraper or putty knife, let it dry, then sand flush before staining, painting or coating. For most scratches, simply rub a Waxstix across the damage. For deeper marks, warm the stick with a flame and let the hot wax flow into the area. Scrape off any excess with a plastic scraper or a piece of cardboard. Blend more than one stick if you need a closer colour match.Important notesDrying time for the filler depends on how deep the fill is, so allow extra time for deeper repairs before sanding. Colour is easiest to judge by testing on an offcut or an out-of-sight spot first. Keep the lid on the tub when not in use to prevent it drying out. Not intended for exterior timber.Specifications Brand Timbermate Product Timber Touch Up Kit, Mixed Colours Kit contents 4 x Timbermate water-based woodfiller tubs and 4 x Waxstix touch-up crayons Colours Pine, Walnut, Hardwood (Tasmanian Oak), Mahogany Base Water-based wood filler (no acrylic or latex) and synthetic wax crayon (no beeswax) Application Filler by scraper or putty knife; Waxstix rubbed on or melted in Finishing Sandable, paintable and stainable Pack dimensions Approx. 165 x 117 x 35 mm Use Interior only SafetyUse with normal care. Work in a well-ventilated area and wear gloves if you prefer to keep your hands clean. If you heat a Waxstix, keep flammable materials away, take care with the hot wax and let it cool before handling. Keep out of reach of children and store the tubs sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Tradie's Bog is a fast-setting, two part polyester building filler for repairing timber and most common building materials, supplied here in a 550g pack. It is built for quick, hard-wearing repairs where a lightweight filler would not hold up, and it can be sawn, drilled, sanded and painted once set. About the formulaA cream polyester resin paste that you mix with the supplied hardener to start the cure. It grips well to a wide range of building surfaces and sets hard in around 20 minutes, with minimal shrinkage, so you can shape it, sand it and move on to painting quickly. The cream base can be tinted with cement oxides or paint tinters if you add the colour before the hardener. Where to use itIndoors: repairing window and door frames, architraves, skirting boards and sashes, and filling holes, cracks and damaged edges in timber and plasterboard.Outdoors: patching external timber joinery, masonry, concrete and metal, then finishing with a suitable paint system. Suitable materials include timber, plasterboard, concrete, brick, fibreglass, metal, alloy, tiles and ceramics. How to use itMake sure the area to be repaired is clean, dry, unpainted and free of oil and grease. Stir the bog before use, then work out a short ribbon of hardener (about 2.5cm for every heaped tablespoon, or roughly 20g, of bog) and mix thoroughly on a clean surface until the colour is even. Press the mix into the repair with a spatula and overfill slightly. For dents in steel or aluminium that will see heavy vibration, punching or drilling the metal first gives the filler a better key. Shape off the excess with a Surform or rasp before it goes rock hard, then use ordinary files or sandpaper once fully set. Clean tools with mineral turpentine before the product cures. Important notesWorking time is about 5 minutes at 23°C, so mix only what you can apply straight away. The filler is rigid, so it is not suited to joints or areas where movement is expected, nor to areas under constant water immersion. It will not bond to polyethylene, polypropylene or PTFE (Teflon). Colour must be added before the hardener. The filler can be painted once cured. Specifications Brand Selleys Product Tradie's Bog Two Part Polyester Building Filler Pack 550g (filler with hardener) Colour Cream Base Two part polyester Application Mixed by hand and applied with a spatula Work time About 5 minutes at 23°C Cure time About 20 minutes Finishing Can be sawn, drilled, tapped, sanded and painted Clean up Mineral turpentine (before cure) Use Interior and exterior SafetyUse in a well-ventilated area, away from heat and open flame, and wear gloves and safety glasses when mixing and sanding. Avoid contact with skin and eyes. Keep out of reach of children and store the pack tightly closed in a cool, dry place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Roberts Quick-Repair Floor Putty in Black is a ready-to-use acrylic filler for hiding gaps, nicks, scratches and fastener holes in laminate, vinyl, hybrid and engineered timber floors, supplied in a handy 88ml squeeze tube. It suits quick touch-ups on an existing floor as well as tidying up during installation, and it can be used straight from the tube or blended with other shades in the Roberts range to get a closer match to your flooring.About the formulaAn acrylic-based putty that is ready to use with no mixing. Roberts describes it as fast drying and non-shrinking, so the fill stays level with the surface. Once dry it can be sanded or painted over. The manufacturer lists it as low VOC, and each tube has a two-year shelf life.Where to use itIndoors: filling nail and screw holes made during floor installation, closing small gaps between boards or planks, and covering chips, dents and scratches on floors that are already down.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, vinyl, hybrid flooring, engineered timber and timber flooring. Black is a good base shade for dark floors, and it can be blended with other Roberts putty colours for in-between tones.How to use itClean the damaged area so it is free of dust and loose debris. Knead the tube thoroughly for at least 20 seconds before use. Squeeze putty into the gap, hole or scratch and press it in firmly so it fills the void, then smooth it level with the surrounding floor. Wipe away excess with a damp rag straight away and do not let putty dry on the surrounding flooring. If you need a custom shade, mix small amounts of different colours before applying, and test the match in an inconspicuous spot first. Once dry, the repair can be lightly sanded or painted if needed.Important notesColour can look slightly different once dry, so test first. Reseal the tube tightly after use, because putty left exposed to air can dry out in the tube. Heavily trafficked spots such as doorways may need a further touch-up over time. This is a cosmetic filler, not a structural repair product or an adhesive.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range), model PC7743 Pack 1 x 88ml squeeze tube Colour Black Base Acrylic Application Squeeze tube, applied by hand Dry time Around 30 minutes (distributor data, varies with depth and conditions) Finish Matte Shelf life 2 years Use Interior flooring repairs SafetyKeep out of reach of children, avoid contact with eyes and prolonged skin contact, and wash hands after use. Store the tube sealed in a cool, dry place away from frost. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Roberts Quick-Repair Floor Putty in Natural is a ready-to-use acrylic repair putty for patching gaps, nicks and scratches in laminate, hybrid, vinyl and engineered timber floors, supplied in an 88ml squeeze tube. It works for both fresh installations and repairs to existing floors, and it can be mixed with other Roberts shades when you need a closer colour match.About the formulaAn acrylic-based putty that comes ready to use straight from the tube. The manufacturer describes it as fast drying, non-shrinking and easy to sand or paint once dry. It is low VOC and has a two-year shelf life. Natural is a light beige base shade that suits many flooring tones. It can be used on its own or blended with other shades in the range.Where to use itIndoors: fill nail and screw holes left during floor installation, close small gaps at plank edges, and touch up nicks, chips and scratches on existing floors.Suitable floors include laminate, hybrid, vinyl (including luxury vinyl plank and tile) and engineered timber.How to use itStart with a clean surface, free of dust and debris. Pick the shade that best matches the repair. The manufacturer advises matching to the lightest base colour of the floor, and you can mix shades to fine-tune it. Knead the tube thoroughly for at least 20 seconds, cut the tip to suit the bead size you need, and squeeze the putty into the damaged area. Work it into the gap, nick or scratch with a putty knife. Wipe off the excess straight away with a damp rag and do not let it dry on the surrounding floor. Once dry it can be lightly sanded or painted if needed.Important notesPutty can dry to a slightly different shade from how it looks in the tube, so test a small, discreet spot first. Reseal the tube after use, because putty left exposed can dry out. Mix and match shades before applying, not after. Check the manufacturer instructions if you plan to coat the repair with a clear finish.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range) Model PC7741 Size 88ml tube Colour Natural (beige) Base Acrylic Application Squeeze tube, spread with a putty knife Finish after cure Matte Shelf life 2 years Use Indoor flooring repairs and installation SafetyIt is a low VOC, water-based acrylic putty. As with any building product, keep it out of reach of children, avoid contact with eyes, and wash your hands after use. Store the tube sealed in a cool place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

The Turbo Timber Rot Repair Kit is a two-step system for rescuing rotted or damaged timber, bundling a wood hardener and a rebuilding filler with the basic tools to apply and finish the repair. It suits window sills, frames, sashes, French doors, architraves, decks and fences, and is aimed at minor repair jobs where replacing the timber would cost far more.About the formulaThe kit pairs two products that are designed to work together. Turbo Rot Fix is a water-based, self-crosslinking emulsion: as the water evaporates, it triggers the resin to cure into a hard plastic that binds loose, rotted fibres back into a firm base. Turbo Builder's Bog is a trade-quality, two-part polyester filler that holds its shape on large fills without slumping, can be mixed to set faster or slower, and can be sanded, drilled and painted much like real timber. Because it cures chemically rather than drying, there are no solvents to evaporate away.What is in the kit Turbo Rot Fix wood hardener, 250ml Turbo Builder's Bog timber repair filler, 500ml Putty knife Sanding block Where to use itIndoors: window sills, frames, sashes, architraves, door jambs and other painted joinery that has gone soft.Outdoors: external window and door frames, French doors, decks, fences and outdoor furniture.Designed for timber. Rot Fix can also act as a sealer ahead of other Turbo bogs on dusty or porous surfaces, but this kit is intended for timber repair.How to use itCut away or scrape out loose, crumbling material and make sure the timber is clean and dry. Spray Rot Fix onto the affected area so it soaks into the soft fibres, then let it dry fully so it hardens and the surface turns firm. Mix Builder's Bog with its hardener according to the instructions on the tin, adjusting the ratio within the stated range to set fast or slow. Press it into the repair with the putty knife, building up the shape. You can trim or shape it while it is part-cured to save sanding time. Once set, sand smooth with the sanding block, then prime and paint as usual. Mix only what you can use before it sets, and wash tools promptly.Important notesTurbo describes Rot Fix as suited to cosmetic and weatherproofing repairs, not structural repairs, so do not rely on it to restore load-bearing strength. Apply to dry timber only, as moisture stops the product soaking in properly. Rot Fix gets sticky as it dries, so keep it away from children. Builder's Bog is a two-part system and needs its hardener to cure. Always follow the mixing directions on the pack.Specifications Brand Turbo Product Timber Rot Repair Kit Pack Kit: Rot Fix 250ml, Builder's Bog 500ml, putty knife, sanding block Rot Fix chemistry Water-based self-crosslinking emulsion Builder's Bog chemistry Two-part unsaturated polyester filler Builder's Bog appearance Buff-coloured paste Application Rot Fix sprayed on; Builder's Bog applied by putty knife Finishing Can be sanded, drilled and painted Use Interior and exterior SafetyUse only with good ventilation, away from heat, sparks and flames, and wear gloves and eye protection, plus suitable respiratory protection if ventilation is poor. Store both products in tightly closed containers in a cool, dry place, below 30°C. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Roberts Quick-Repair Putty in Grey is a ready-to-use floor repair filler for hiding gaps, nicks, scratches and fastener holes in laminate, vinyl, hybrid and engineered or timber floors, supplied in a handy 88ml squeeze tube. It suits both fresh installations and repairs to floors that are already down, and it can be used straight from the tube or blended with other Roberts shades to match your flooring.About the formulaAn acrylic-based putty that dries quickly and is made not to shrink back as it dries. It sands smoothly and can be painted over, so you can fine-tune the colour or finish once it has set. It is a low VOC product with a two-year shelf life, and the soft tube lets you squeeze out a controlled bead for neat, quick application.Where to use itIndoors: filling nail and screw holes during floor installation, closing small gaps between boards or planks, and touching up chips, dents and scratches on existing laminate, vinyl, hybrid and timber floors.Outdoors: not intended for outdoor use.Suitable surfaces include laminate flooring, vinyl flooring, hybrid flooring, engineered timber and solid timber floors. Grey is a mixable base shade, so test your colour match on an offcut or a hidden spot before committing to a visible repair.How to use itClean the area first so it is free of dirt, dust and grease. Knead the tube well for about 20 seconds, then snip the tip to suit the size of bead you need. Press the putty firmly into the gap or hole and smooth it level with the floor. Wipe any excess off the surrounding floor with a damp rag before it dries, because dried-on filler is much harder to remove. If you need a closer colour match, mix shades before applying. Once the putty has fully cured it can be sanded flush or painted if required.Important notesAlways choose or blend a shade that matches the lightest base colour of your floor. Store at room temperature and do not let the tube freeze, as freezing can affect performance. Cure and recoat times vary with bead depth, temperature and humidity, so allow the repair to cure fully before sanding, painting or walking on it heavily. Reseal the tube after use to keep the remaining putty usable.Specifications Brand Roberts Product Quick-Repair Putty (Model PC7728) Size 88ml tube (3 oz) Colour Grey Base Acrylic Application Squeeze tube, hand applied Finish Sandable and paintable VOC Low VOC Shelf life 2 years Use Interior flooring repairs SafetyIf it gets in your eyes, rinse with plenty of water. Keep out of reach of children and store the tube sealed at room temperature, away from freezing. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Gilly's Beeswax Filler Sticks are coloured wax sticks for repairing cracks, gaps and small holes in timber, supplied here as an assorted pack of six sticks in different wood tones. You pick the shade closest to your timber, work the wax into the damage and finish the surface, which suits furniture, cabinets, frames and general timber touch-ups.About the formulaThese are pigmented wax fillers made from pure beeswax, natural pigments and a natural hardener. Once set, the wax can be buffed to a fine finish and coated with most materials. The manufacturer says the colours can be blended, and leftover wax can be melted down and reused.Where to use itIndoors: filling nail holes, gaps, joins and cracks in furniture, cabinetry, frames and other timber items.Outdoors: the manufacturer does not publish outdoor performance data for this product, so it is best treated as a timber repair filler for interior and finished-furniture work.Suitable for most wood surfaces, in both soft and hard woods. It is aimed at damage wider or deeper than about 1mm. Very fine scratches and surface blemishes are better treated with a wax product made for that job.How to use itStart with a clean, dry surface and apply the filler to raw timber before any oil, wax or lacquer finish. Pick the stick closest to the timber, or melt two colours together to blend a custom match. Soften the wax with a soldering iron, a hot knife, or gentle heat from a heat gun or hairdryer. Take care, because extra heat can affect the surrounding finish. You can also soften a stick briefly in a microwave. Test in very short bursts, as it only needs to become malleable. Press the softened wax into the gap. For larger repairs, chip off the amount you need and melt it into the gap. Once the wax has firmed up again, scrape off the excess with a plastic spatula or an old card, then buff to a smooth finish. Important notesThe wax firms up quickly after application, typically within about 10 to 30 minutes depending on conditions. Rubbing a cold stick over a gap like a crayon works, but adhesion is better when the wax has been melted. Beeswax can ignite when overheated, so the manufacturer advises caution and says not to apply an open flame directly to the sticks. The product may contain traces of bee pollen and soy. If you plan to use it on a surface that will touch food, check suitability with the manufacturer first, as the coloured sticks are pigmented.Specifications Brand Gilly's Australia Product Beeswax Filler Sticks, Assorted Pack 6 sticks, 15g each (about 90g in total) Stick size About 83mm long x 15mm diameter Colours Pale brown (natural), orange/brown, mid brown, red/brown, dark brown, black (one of each) Base Beeswax with natural pigments and natural hardener Application Hand applied; melt or soften the wax, press into the gap, then scrape back and buff Firming time About 10 to 30 minutes, depending on conditions Use Timber repair, applied before the final finish Origin Made in Australia SafetyTake care when heating the wax, as molten wax can burn skin and beeswax can ignite at high temperatures. Keep it away from open flames and avoid overheating. Allow the wax to cool before handling. Store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys No More Gaps Timber Floors in Baltic is a flexible, wood-fibre gap filler made for sealing the gaps between tongue and groove floorboards, supplied as a single 380g cartridge. The Baltic tint is made to sit in lighter timber floors, so the repair blends in once it has been sanded and finished.About the formulaA water-based acrylic filler loaded with real wood fibre. The fibre helps the cured filler take stain better than a standard gap filler, and it sands back to a smooth, clean surface. It stays flexible to cope with the seasonal movement of floorboards and forms an airtight seal that helps keep out draughts, dust and pests. Baltic is tinted to suit pine, myrtle and alpine ash. Hardwood, Jarrah and Walnut tints are available separately for other timbers.Where to use itIndoors: gaps around and between tongue and groove timber flooring, and between timber panels and fittings such as skirting boards, architraves and benchtops.Outdoors: not suitable. This is an interior-only product.Suitable materials include timber flooring, timber panels and fittings, and engineered timber floors. The Baltic tint is the best match for pine, myrtle and alpine ash.How to use itMake sure the gap is clean, dry and free of dust. Cut the cartridge seal and nozzle to suit the width of the gap, fit the nozzle and load the cartridge into a caulking gun. Force the filler well into the gap, then press it in and smooth it off with a spatula, taking care not to drag filler back out of the joint. Scrape surplus filler off the timber surface with the spatula to cut down on sanding later, and wipe up any smears straight away with a damp cloth. Allow the filler to cure fully before sanding, staining, varnishing or painting. Wear a P1 dust mask when sanding.Important notesNot for exterior use. Not for gaps wider than 3mm in trafficable joints. Allow at least 24 hours to cure, and longer in cold or damp conditions. Uncured filler cleans up with water, while cured filler needs to be sanded or scraped off. Keep the cartridge stored above 5°C. Test stains and finishes on a small area first, as the final colour depends on the timber and the finish used.Specifications Brand Selleys Product No More Gaps Timber Floors Gap Filler Pack 1 x 380g cartridge Colour Baltic (suits pine, myrtle, alpine ash) Base Water-based acrylic with real wood fibre Application Cartridge, via caulking gun Full cure 24 hours Coverage About 18 m of 3mm bead per cartridge Sandable Yes Stainable Yes Paintable Yes Clean up Water (while uncured) Use Interior only SafetyAvoid prolonged skin contact and keep the product out of the eyes, and wash your hands after use. Wear a P1 dust mask when sanding the cured filler. Keep out of reach of children and avoid letting the product enter waterways. Store above 5°C. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Plastic Wood is a fast-setting, solvent-based wood filling cement for repairing holes, dents and chips in interior timber, supplied here in a 230g maple-coloured tin. It is a simple fix for furniture, skirting, architraves and other indoor joinery, and once set it can be worked much like the timber around it.About the formulaA solvent-based paste containing natural wood fibres, finished in a maple (tan) colour. It dries quickly to a hard finish that holds up to sanding, nailing and planing. Once dry it can be stained, varnished, painted or lacquered, so the repair can be finished in the same way as the surrounding wood. It is a rigid filler, so it is not designed for joints that move.Where to use itIndoors: filling nail holes, dents, chips and small cracks in furniture, doors, window frames, skirting boards, architraves and other interior woodwork.Outdoors: not recommended. The manufacturer rates this product for interior use only.Suitable materials include natural timber and wood veneer.How to use itStir the product thoroughly before use. Make sure the surface is clean, dry and free of loose material. Press the filler in with a putty knife and slightly overfill deeper holes so there is room to sand back flush. Do not fill deeper than 6mm in a single application. Let it dry fully before sanding, staining, painting or lacquering. Wipe the putty knife clean with methylated spirits. Press the lid on firmly after use and store the tin somewhere cool.Important notesNot suitable for exterior use. Not recommended where structural movement may occur, so use a flexible product for joints and gaps between surfaces. Work in a well-ventilated area. Colour is maple only, so test a small area first if you need to match a different timber tone, or plan to stain or paint over the repair.Specifications Brand Selleys Product Plastic Wood Filler Cement Size 230g tin Colour Maple Base Solvent-based, with natural wood fibres Application Putty knife Maximum fill depth 6mm per application Set speed Fast setting Clean up Methylated spirits Use Interior only SafetyThis is a highly flammable solvent-based product. Keep it away from heat, sparks, flames and other ignition sources, and avoid static discharge. It can irritate skin and eyes, and the vapours may cause drowsiness or dizziness. Use only in a well-ventilated area and avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Turbo Builder's Bog is a trade quality, two part polyester filler for repairing damaged and rotted timber, supplied here in a 500ml can for builders, painters and capable DIYers. It sets to a hard, wood-like finish that you can sand, drill and paint, so it suits window sills, door frames and other jobs where replacing the timber is not practical.About the formulaA polyester-based filler paste that cures by a chemical reaction when mixed with the red hardener paste, rather than by drying out. Because of this, it shows no obvious shrinkage. You choose the working time by adjusting how much hardener you add within the range printed on the can, and the mix also sets faster in warm weather. As it sets it passes through a soft, cheese-like stage where it can be trimmed with a blade or a surform file. Shaping at this point saves a lot of sanding. It spreads smoothly, holds its shape on large fills without slumping, and bonds firmly to timber.Where to use itIndoors: filling holes, gaps and dents in architraves, skirtings, door frames and other timber trims before painting.Outdoors: repairing window sills, sashes, fascias, decks and door frames, including areas where the timber is partly rotten, once the soft material has been cleared back to sound wood.Suitable material is timber. It is designed as a timber repair filler and can be painted over once cured. Test first before using on other surfaces.How to use itMake sure the timber is clean, dry, unpainted, roughened and free of rot. Remove any soft or crumbling material first. Place the amount of filler you need on a clean, flat, non-absorbent surface, such as the plastic over-cap. Add the red hardener in the proportion given on the can, then mix thoroughly until the colour is completely even with no red or white streaks. As a guide from the manufacturer's mixing chart, 100g of filler with 2.5g of hardener gels in about 7 minutes at 22°C. Use less hardener if you need longer working time, particularly in warm weather. Press the mix into the repair with a putty knife or spatula, overfilling slightly. When it reaches the cheese-like stage, trim it to shape with a blade or surform. Allow about 30 to 60 minutes for a full cure, then sand and paint. Mix a small test batch first, because temperature and thickness change the set time.Important notesAlways follow the mix ratio on the can, because too little or too much hardener can affect the cure. Thick fills set faster than thin ones. Timber will still expand and contract with moisture changes, so good woodworking practice should still be followed around the repair. Mixed material generates heat as it cures. Do not leave mixed product in a pile or sealed container. Close the can tightly after use. Check the can and the supplied instructions for full details.Specifications Brand Turbo Product Builder's Bog timber repair filler Size 500ml can Colour Beige / buff paste Base Two part unsaturated polyester filler (cured with red hardener paste) Application Hand applied with a putty knife or spatula Gel time Adjustable by hardener amount; about 7 minutes in the 100g to 2.5g example at 22°C Full cure About 30 to 60 minutes Finishing Sandable, drillable and paintable Use Interior and exterior Country of manufacture New Zealand SafetyIt has a characteristic styrene odour. Use outdoors or in a well-ventilated area, avoid breathing vapours, and keep away from heat, sparks, open flames and other ignition sources. Keep the container tightly closed, out of reach of children, and stored in a dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less