Selleys Tradie's Bog is a fast-setting, two part polyester building filler for repairing timber and most common building materials, supplied here in a 550g pack. It is built for quick, hard-wearing repairs where a lightweight filler would not hold up, and it can be sawn, drilled, sanded and painted once set. About the formulaA cream polyester resin paste that you mix with the supplied hardener to start the cure. It grips well to a wide range of building surfaces and sets hard in around 20 minutes, with minimal shrinkage, so you can shape it, sand it and move on to painting quickly. The cream base can be tinted with cement oxides or paint tinters if you add the colour before the hardener. Where to use itIndoors: repairing window and door frames, architraves, skirting boards and sashes, and filling holes, cracks and damaged edges in timber and plasterboard.Outdoors: patching external timber joinery, masonry, concrete and metal, then finishing with a suitable paint system. Suitable materials include timber, plasterboard, concrete, brick, fibreglass, metal, alloy, tiles and ceramics. How to use itMake sure the area to be repaired is clean, dry, unpainted and free of oil and grease. Stir the bog before use, then work out a short ribbon of hardener (about 2.5cm for every heaped tablespoon, or roughly 20g, of bog) and mix thoroughly on a clean surface until the colour is even. Press the mix into the repair with a spatula and overfill slightly. For dents in steel or aluminium that will see heavy vibration, punching or drilling the metal first gives the filler a better key. Shape off the excess with a Surform or rasp before it goes rock hard, then use ordinary files or sandpaper once fully set. Clean tools with mineral turpentine before the product cures. Important notesWorking time is about 5 minutes at 23°C, so mix only what you can apply straight away. The filler is rigid, so it is not suited to joints or areas where movement is expected, nor to areas under constant water immersion. It will not bond to polyethylene, polypropylene or PTFE (Teflon). Colour must be added before the hardener. The filler can be painted once cured. Specifications Brand Selleys Product Tradie's Bog Two Part Polyester Building Filler Pack 550g (filler with hardener) Colour Cream Base Two part polyester Application Mixed by hand and applied with a spatula Work time About 5 minutes at 23°C Cure time About 20 minutes Finishing Can be sawn, drilled, tapped, sanded and painted Clean up Mineral turpentine (before cure) Use Interior and exterior SafetyUse in a well-ventilated area, away from heat and open flame, and wear gloves and safety glasses when mixing and sanding. Avoid contact with skin and eyes. Keep out of reach of children and store the pack tightly closed in a cool, dry place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$32.71
Turbo Builders Bog Hardener is the red catalyst paste that turns Turbo Builders Bog and other polyester body fillers from a workable putty into a hard, sandable repair, supplied here in a 40g pack. You control how fast the filler sets by adjusting how much hardener you add, so you can slow things down for a big fill or speed them up on a cold day.About the formulaA red paste made from 50% benzoyl peroxide in an emulsion base, designed as the second component for Turbo Builders Bog and body fillers. Once it is mixed through the filler, it starts a chemical reaction that cures the repair from the inside out. Turbo also positions its red hardener for use with its Concrete Bog and Metal Bog, and for other polyester fillers.Where to use itIndoors: repairing timber architraves, door frames, skirtings, window sashes, benches and furniture with Turbo Builders Bog.Outdoors: rebuilding rotted window sills, door bases and weatherboards, and filling dents in vehicle panels with polyester body filler.Use it with Turbo Builders Bog, Turbo Concrete Bog, Turbo Metal Bog and other polyester body fillers. The hardener is not a stand-alone product, so it is always mixed into a compatible filler.How to use itPrepare the repair area first. For timber, it should be clean, dry, unpainted, roughened and free of rot. Scoop out the amount of filler you need onto a clean, flat, non-absorbent surface, add the hardener, and mix thoroughly until the colour is completely uniform with no white or red streaks. As a guide from Turbo's mixing directions for Builders Bog, about 2.5g of hardener to 100g of filler gives a gel time of roughly 7 minutes at 22°C. Use more hardener in cold weather or for a faster set, and less in hot weather or when you need more working time. Always stay within the mixing range printed on your filler's tin or pack. Apply the mix promptly with a flat spreader. Once it gels to a firm, cheese-like stage you can trim, grate or shape it. Allow it to cure fully, then sand and paint.Important notesMixing ratios and set times vary with temperature, the amount mixed and the thickness of the fill, so mix small test batches if you are unsure. Warmer conditions need less hardener for the same set time. Too little hardener can leave the filler soft or slow to cure, so do not go below the range on the filler's directions. Once hardener is mixed in, the filler cannot be re-softened, so only mix what you can apply in the working time.Specifications Brand Turbo Product Builders Bog Hardener (Red Hardener) Pack 40g Colour Red Base 50% benzoyl peroxide paste (emulsion) Application Mixed by hand into polyester filler Example gel time About 7 minutes at 22°C (2.5g per 100g Builders Bog) Compatible with Turbo Builders Bog, Concrete Bog, Metal Bog and other polyester fillers Use Interior and exterior repairs (via the filler) SafetyUse with normal care: work in a well-ventilated area, keep away from heat and open flame, and wear gloves and safety glasses to avoid contact with eyes and skin. Keep it out of reach of children, store it in a cool, dry place with the cap tightly closed, and keep it separate from other chemicals. Refer to the Safety Data Sheet (SDS) for full details.
$8.45
Screw-It-Again is a snap-off plastic wood anchor that rescues stripped or worn screw holes in timber, MDF, plywood and particleboard, supplied here as a pack of four. Instead of filling the hole with glue and sawdust and waiting for it to dry, you screw the anchor into the damaged hole, snap it to length and refit your original screw, all with a basic screwdriver.About the designEach anchor is a tapered, threaded plastic fastener with a notched head, so it can be driven in with a screwdriver. It is scored into sections so a single anchor suits a range of hole and screw sizes, and the manufacturer states that one anchor can repair several stripped holes. A side slit allows for expansion as the screw goes in. Per the manufacturer, the 2 inch anchor suits screws from #2 to #16.Where to use itIndoors: loose or sagging door and cabinet hinges, furniture, wooden toys, guitar necks and any other spot where a wood screw has lost its grip.Outdoors: the manufacturer does not specify outdoor performance for the wood anchor, so check suitability for your project before using it in exposed locations.Suitable materials include solid timber, MDF, plywood and particleboard.How to use it1. Match: use the illustration on the pack to match your screw size to the right section of the anchor, then snap off that section.2. Screw: gently drive the anchor into the existing stripped hole with a screwdriver.3. Snap: when it will not go any further, snap the anchor off at the desired length by hand or with pliers. Keep the leftover piece for another repair.4. Screw it again: put your original screw into the anchor and tighten it securely.Important notesFollow the pack instructions carefully, especially the snap step, so the anchor ends up at the right size for your screw. Screws are not included. This anchor is designed for wood-based materials. For concrete, brick or tile, use a masonry anchor instead. There is no glue involved, so there is no cure time to wait for.Specifications Brand Screw-It-Again Product Snap-Off Wood Anchor, Screw Hole Repair Pack 4 anchors Material Plastic Anchor length 2 inch (per manufacturer) Screw sizes #2 to #16 (per manufacturer) Application Hand installed with a screwdriver Suitable for Timber, MDF, plywood, particleboard SafetyAs good practice, wear safety glasses when snapping the anchor or working overhead, and keep the small parts away from young children. Refer to the Safety Data Sheet (SDS) for full details.
$8.86
Protite Fibreglass Chopped Matting is a strand-chopped glass fibre mat that adds strength and reinforcement to fibreglass repairs, supplied here as a 1m x 1m sheet. It is an economical, general-purpose reinforcement for boats, caravans, trailers, surfboards, gutters, downpipes and water tanks. It is designed to be laminated with Protite Fibreglass Resin and Protite Resin Catalyst Hardener.About the materialThe mat is made from strands of glass fibre laid randomly across each other and bound together. The loose, random layout gives similar stiffness in every direction, and the mat conforms to tight curves and corners more readily than woven cloth. It is a 450gsm mat with a rough finish. It suits general, non-structural repair and lay-up work. Protite recommends it for adding strength and rigidity to repairs. Woven cloth gives a smoother and more flexible finish if that is what the job needs.Where to use itIndoors: general fibreglass repair and reinforcement on rigid items such as moulded parts, timber and other suitable substrates.Outdoors: down pipes, leaky gutters, metal roofs and rusted panels, plus boats, caravans, trailers, surfboards and water tanks.Protite lists steel, iron, aluminium, timber, PVC, masonry and smooth polyester or wooden surfaces as suitable for repair with its fibreglass system. As with any repair, check the resin instructions and test a small area first on unusual substrates.How to use itPrepare the surface so it is clean, dry and sanded or keyed as the resin instructions advise. Cut the mat to the repair shape and allow for an overlap of about 3cm around the damage. Tease out the fibres at the edge to create a feathered edge that blends in. Mix only as much resin and hardener as you can use quickly, following the ratios on the resin pack, because it begins to gel and cure once the hardener is added. Apply a wet coat of resin to the surface, lay the mat in place, then dab more resin over the top without brushing, so the mat does not shift. Make sure the fibres are fully wetted out. Gently roll out trapped air with a fibreglass roller, then leave the resin to cure fully before sanding, filling and painting.Important notesThe mat is a reinforcement only and needs compatible polyester resin and hardener to form a repair (both sold separately). Cure times depend on the resin, the amount of hardener and the temperature, so follow the resin pack. Cut ends and sanded surfaces release fine glass fibres, so avoid breathing the dust and wear suitable protection. A finished repair can be sanded and painted.Specifications Brand Protite Product Fibreglass Chopped Matting Size 1m x 1m (1m²) Material Strand-chopped fibreglass mat Weight of mat 450gsm Finish Rough Appearance Yellow to white fibres bound together in strands Use with Protite Fibreglass Resin and Protite Resin Catalyst Hardener Application Hand lay-up, cut to shape and wetted out with resin Use Interior and exterior SafetyAvoid breathing in fibres or dust, work in a well-ventilated area, and use mechanical extraction at the source if power tools are used for cutting or sanding. Do not let the product enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$42.20
Turbo Metal Builders Bog is a two part, aluminium and glass fibre reinforced polyester filler for rusted metal, dents, cracks, holes and tears, supplied here as a 500ml can. It is aimed at panel beaters, builders and DIYers who want a hard, workable repair that can go over or under ordinary body filler for extra strength, and which also works on fibreglass, wood, stone, concrete and aluminium.About the formulaThe filler is a paste based on unsaturated polyester resin in styrene, loaded with aluminium so you can repair metal with a metal-filled compound, and with glass fibre strands that help bridge holes and gaps. Once catalysed with a separate peroxide-based hardener, the mix gels to a cheese-like consistency that can be cut, shaped or pared, then cures hard. Changing the amount of hardener lets you speed up or slow down the set to suit the job and the weather. Turbo describes it as having minimal shrinkage, good stress resistance and flexibility, water resistance and rust-inhibiting properties.Where to use itIndoors: repairing holes, cracks and damaged areas in fibreglass, wood, stone and concrete, and filling larger voids where a standard filler would sag or shrink.Outdoors: rusted-out panels, dents and holes in metal, vehicle bodywork and similar repairs, plus cracked or broken concrete, masonry and aluminium items exposed to weather.Suitable materials include steel and other metals, aluminium, fibreglass, wood, stone, concrete and masonry. It can be used instead of, or underneath, regular plastic body filler.How to use itStart with a clean, dry, sound surface, free of loose rust, paint, oil, grease and dust, and roughen smooth surfaces for a better key. Work out how much filler you need and mix it with the hardener following the directions on the can, stirring until the colour is completely uniform. Because cure speed depends on temperature and the amount of hardener, try a small batch first. Press the mix firmly into the repair, building up and shaping it while it is still soft. Once it has gelled you can trim it, then sand, file, drill, machine and paint it after it has cured hard.Important notesThis is a two part system and will not cure without the hardener, so check the hardener is on hand before you start. More hardener or warmer conditions will shorten the working time, and less hardener will lengthen it. Full cure is typically within about 30 to 60 minutes, and the repair can be painted within the hour, though times vary with temperature and mix. The cured filler is paintable but not stainable. For large structural repairs on metal, make sure the underlying area is sound.Specifications Brand Turbo Product Metal Builders Bog (metallised repairer) Size 500ml can Colour Grey Base Unsaturated polyester resin filler with aluminium and glass fibre Application Hand applied after mixing with hardener Set and cure Gels to a cheese-like consistency, full cure typically about 30 to 60 minutes (varies with hardener and temperature) Paintable Yes, within the hour Sandable Yes Stainable No Shrink resistant Yes UV resistant Yes Use Interior and exterior SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use outdoors or in a well-ventilated area, avoid breathing vapours, and avoid contact with eyes, skin and clothing. Wear suitable gloves and eye protection. Wash exposed skin thoroughly after handling and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details.
$32.41
![Roberts Quick-Repair Floor Putty 88ml [Black] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-black-2.png?v=1792410973&width=645)
Roberts Quick-Repair Floor Putty in Black is a ready-to-use acrylic filler for hiding gaps, nicks, scratches and fastener holes in laminate, vinyl, hybrid and engineered timber floors, supplied in a handy 88ml squeeze tube. It suits quick touch-ups on an existing floor as well as tidying up during installation, and it can be used straight from the tube or blended with other shades in the Roberts range to get a closer match to your flooring.About the formulaAn acrylic-based putty that is ready to use with no mixing. Roberts describes it as fast drying and non-shrinking, so the fill stays level with the surface. Once dry it can be sanded or painted over. The manufacturer lists it as low VOC, and each tube has a two-year shelf life.Where to use itIndoors: filling nail and screw holes made during floor installation, closing small gaps between boards or planks, and covering chips, dents and scratches on floors that are already down.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, vinyl, hybrid flooring, engineered timber and timber flooring. Black is a good base shade for dark floors, and it can be blended with other Roberts putty colours for in-between tones.How to use itClean the damaged area so it is free of dust and loose debris. Knead the tube thoroughly for at least 20 seconds before use. Squeeze putty into the gap, hole or scratch and press it in firmly so it fills the void, then smooth it level with the surrounding floor. Wipe away excess with a damp rag straight away and do not let putty dry on the surrounding flooring. If you need a custom shade, mix small amounts of different colours before applying, and test the match in an inconspicuous spot first. Once dry, the repair can be lightly sanded or painted if needed.Important notesColour can look slightly different once dry, so test first. Reseal the tube tightly after use, because putty left exposed to air can dry out in the tube. Heavily trafficked spots such as doorways may need a further touch-up over time. This is a cosmetic filler, not a structural repair product or an adhesive.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range), model PC7743 Pack 1 x 88ml squeeze tube Colour Black Base Acrylic Application Squeeze tube, applied by hand Dry time Around 30 minutes (distributor data, varies with depth and conditions) Finish Matte Shelf life 2 years Use Interior flooring repairs SafetyKeep out of reach of children, avoid contact with eyes and prolonged skin contact, and wash hands after use. Store the tube sealed in a cool, dry place away from frost. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Natural] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-natural-2.png?v=1792410959&width=645)
Roberts Quick-Repair Floor Putty in Natural is a ready-to-use acrylic repair putty for patching gaps, nicks and scratches in laminate, hybrid, vinyl and engineered timber floors, supplied in an 88ml squeeze tube. It works for both fresh installations and repairs to existing floors, and it can be mixed with other Roberts shades when you need a closer colour match.About the formulaAn acrylic-based putty that comes ready to use straight from the tube. The manufacturer describes it as fast drying, non-shrinking and easy to sand or paint once dry. It is low VOC and has a two-year shelf life. Natural is a light beige base shade that suits many flooring tones. It can be used on its own or blended with other shades in the range.Where to use itIndoors: fill nail and screw holes left during floor installation, close small gaps at plank edges, and touch up nicks, chips and scratches on existing floors.Suitable floors include laminate, hybrid, vinyl (including luxury vinyl plank and tile) and engineered timber.How to use itStart with a clean surface, free of dust and debris. Pick the shade that best matches the repair. The manufacturer advises matching to the lightest base colour of the floor, and you can mix shades to fine-tune it. Knead the tube thoroughly for at least 20 seconds, cut the tip to suit the bead size you need, and squeeze the putty into the damaged area. Work it into the gap, nick or scratch with a putty knife. Wipe off the excess straight away with a damp rag and do not let it dry on the surrounding floor. Once dry it can be lightly sanded or painted if needed.Important notesPutty can dry to a slightly different shade from how it looks in the tube, so test a small, discreet spot first. Reseal the tube after use, because putty left exposed can dry out. Mix and match shades before applying, not after. Check the manufacturer instructions if you plan to coat the repair with a clear finish.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range) Model PC7741 Size 88ml tube Colour Natural (beige) Base Acrylic Application Squeeze tube, spread with a putty knife Finish after cure Matte Shelf life 2 years Use Indoor flooring repairs and installation SafetyIt is a low VOC, water-based acrylic putty. As with any building product, keep it out of reach of children, avoid contact with eyes, and wash your hands after use. Store the tube sealed in a cool place. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Dark Brown] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-dark-brown-2.png?v=1792410954&width=645)
Roberts Quick-Repair Floor Putty in Dark Brown is a ready-to-use acrylic filler for hiding gaps, nicks and scratches in modern click-together and plank flooring, supplied in a handy 88ml squeeze tube. It suits quick touch-ups on existing floors as well as tidying up nail and screw holes during installation, and the dark brown shade can be used on its own or blended with other Roberts colours to get closer to your floor.About the formulaAn acrylic-based putty that is formulated to dry quickly without shrinking. Once dry it can be sanded or painted, so you can refine the repair after it sets. It is a low VOC formula, and it is supplied in a soft tube so you can apply it straight from the pack with no mixing. Roberts quotes a two-year shelf life.Where to use itIndoors: filling small scratches, chips, dents and open joints on laminate, hybrid, vinyl and engineered timber floors; concealing nail and screw holes while a floor is being installed; touching up localised damage on floors that are already in place.Outdoors: not intended for exterior use.Suitable surfaces include laminate, hybrid flooring, vinyl flooring and engineered timber flooring. Choose, or mix, a shade that matches the lightest base colour of the floor for the most natural result.How to use itMake sure the area is clean, dry and free of dust and loose debris. Knead the tube thoroughly for at least 20 seconds before use. Squeeze the putty into the gap, nick or hole and work it in with a putty knife or similar tool so it sits flush with the surface. Wipe excess off the surrounding floor with a damp rag before it dries, because dried residue on the floor surface is harder to remove. When the putty has dried it can be lightly sanded or painted if needed. Test the colour on an offcut or an inconspicuous spot first.Important notesThis is a cosmetic filler for small damage, not a structural repair product. Deep chips or large missing areas may need a different repair method. The putty is not rated as water resistant, so it is not recommended for wet areas or continual moisture. Store at room temperature and do not let the tube freeze, as freezing may affect performance. Reseal the tube after use. Colour on screen may vary slightly from the real product, so check the shade before committing to a full repair.Specifications Brand Roberts Product Quick-Repair Floor Putty Size 88ml tube Colour Dark Brown Base Acrylic Application Squeeze tube, applied by hand Finish options Can be sanded or painted once dry Suitable floors Laminate, hybrid, vinyl and engineered timber Shelf life 2 years VOC Low VOC Use Interior floors SafetyIt is marketed as low VOC and safe to use, but normal care still applies: avoid contact with eyes, keep out of reach of children, and wash hands after use. Do not swallow. Store the tube at room temperature and protect it from freezing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-white-2.png?v=1792410948&width=645)
Roberts Quick-Repair Floor Putty in White is a ready-to-use acrylic putty for tidying up gaps, nicks, scratches and fixing holes in laminate, hybrid, vinyl and engineered timber floors, supplied in an 88ml squeeze tube. It suits both new installations and repairs to floors that are already down, and it can be used straight from the tube or blended with other Roberts putty colours to match your flooring.About the formulaAn acrylic-based putty that is designed not to shrink as it dries. It dries quickly, so you can sand or paint over the repair soon after filling. White is a mixable base shade, which means you can lighten other putty colours or tint it to get closer to your floor. It is low in VOCs and has a two-year shelf life.Where to use itIndoors: filling nail and screw holes during floor installation, closing small gaps between boards or planks, and covering chips, nicks and scratches on existing floors.Outdoors: not intended for outdoor use. It is made for interior floors.Suitable floors include laminate, hybrid, vinyl and engineered timber flooring. Always test the colour match in an inconspicuous spot first.How to use itClean the area so it is free of grease and dirt. Knead the tube thoroughly for about 20 seconds, then snip the tip to suit the size of bead you need. Squeeze the putty into the damaged area, spread it and leave it to dry. Once dry it can be sanded smooth or painted over if needed. To match a particular floor, mix small amounts of different putty colours together before you apply.Important notesWhite often won't match a floor on its own, so blend it with other shades when you need an exact colour. Drying time depends on how deep the fill is and on room conditions, so allow extra time for deeper repairs before sanding or painting. Keep the cap on tightly after use and store the tube in a cool, dry place.Specifications Brand Roberts Product Quick-Repair Floor Putty Model number PC7742 Size 88ml squeeze tube Colour White Base Acrylic Application Squeeze from tube, spread by hand or putty knife Finish after cure Matte Shelf life Two years Use Interior flooring SafetyKeep it out of reach of children and avoid contact with eyes and prolonged contact with skin. Wash your hands after use and use it with good ventilation. If it gets in your eyes, rinse with plenty of water. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Greige] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-greige-2.png?v=1792410943&width=645)
Roberts Quick-Repair Floor Putty in Greige is a ready-to-use acrylic filler for patching gaps, nicks and scratches in laminate, hybrid, vinyl and engineered timber floors, supplied in a handy 88ml squeeze tube. It suits both flooring installers and home owners, and the neutral grey-beige shade can be used on its own or mixed with other Roberts putty colours to blend into your floor.About the formulaAn acrylic-based putty that is ready to use straight from the tube, with no mixing and no tools needed beyond a putty knife. It dries quickly, is formulated not to shrink, and can be sanded or painted once dry. It is low in VOCs, and the tube has a shelf life of two years.Where to use itIndoors: filling nail and screw holes left after laying a floor, closing small gaps at plank edges, and hiding chips, nicks and scratches on floors that are already installed.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, hybrid flooring, vinyl (plank and tile) and engineered timber flooring.How to use itMake sure the area is clean and free of grease, dirt and loose debris. Choose the shade closest to your floor, ideally matching the lightest base colour of the surface, or blend two colours together to get a closer match. Knead the tube thoroughly for at least 20 seconds, cut the tip to suit the size of the repair, then press the putty into the damaged area with a putty knife until it is filled. Wipe away excess with a damp rag straight away and do not let it dry on the surrounding floor. Once dry, the repair can be lightly sanded or painted if needed.Important notesColour is best checked on a small hidden spot first, as the shade can look different once dry and on different floors. Store the tube at room temperature and do not let it freeze, as freezing may affect performance. Reseal the tube after use. This putty is made for floor repairs and is not designed to be a structural adhesive or a wet area sealant.Specifications Brand Roberts Product Quick-Repair Floor Putty Size 88ml squeeze tube (single) Colour Greige (grey-beige) Base Acrylic Application Squeeze tube, applied by hand with a putty knife Finish Can be sanded or painted when dry VOC Low VOC Shelf life 2 years Use Indoor floor repair: laminate, hybrid, vinyl and engineered timber SafetySwallowing large amounts may upset the stomach. Wear protective gloves and eye protection when using it. If breathed in, move to fresh air. If it gets on skin, wash off with soap and plenty of water and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
The Turbo Timber Rot Repair Kit is a two-step system for rescuing rotted or damaged timber, bundling a wood hardener and a rebuilding filler with the basic tools to apply and finish the repair. It suits window sills, frames, sashes, French doors, architraves, decks and fences, and is aimed at minor repair jobs where replacing the timber would cost far more.About the formulaThe kit pairs two products that are designed to work together. Turbo Rot Fix is a water-based, self-crosslinking emulsion: as the water evaporates, it triggers the resin to cure into a hard plastic that binds loose, rotted fibres back into a firm base. Turbo Builder's Bog is a trade-quality, two-part polyester filler that holds its shape on large fills without slumping, can be mixed to set faster or slower, and can be sanded, drilled and painted much like real timber. Because it cures chemically rather than drying, there are no solvents to evaporate away.What is in the kit Turbo Rot Fix wood hardener, 250ml Turbo Builder's Bog timber repair filler, 500ml Putty knife Sanding block Where to use itIndoors: window sills, frames, sashes, architraves, door jambs and other painted joinery that has gone soft.Outdoors: external window and door frames, French doors, decks, fences and outdoor furniture.Designed for timber. Rot Fix can also act as a sealer ahead of other Turbo bogs on dusty or porous surfaces, but this kit is intended for timber repair.How to use itCut away or scrape out loose, crumbling material and make sure the timber is clean and dry. Spray Rot Fix onto the affected area so it soaks into the soft fibres, then let it dry fully so it hardens and the surface turns firm. Mix Builder's Bog with its hardener according to the instructions on the tin, adjusting the ratio within the stated range to set fast or slow. Press it into the repair with the putty knife, building up the shape. You can trim or shape it while it is part-cured to save sanding time. Once set, sand smooth with the sanding block, then prime and paint as usual. Mix only what you can use before it sets, and wash tools promptly.Important notesTurbo describes Rot Fix as suited to cosmetic and weatherproofing repairs, not structural repairs, so do not rely on it to restore load-bearing strength. Apply to dry timber only, as moisture stops the product soaking in properly. Rot Fix gets sticky as it dries, so keep it away from children. Builder's Bog is a two-part system and needs its hardener to cure. Always follow the mixing directions on the pack.Specifications Brand Turbo Product Timber Rot Repair Kit Pack Kit: Rot Fix 250ml, Builder's Bog 500ml, putty knife, sanding block Rot Fix chemistry Water-based self-crosslinking emulsion Builder's Bog chemistry Two-part unsaturated polyester filler Builder's Bog appearance Buff-coloured paste Application Rot Fix sprayed on; Builder's Bog applied by putty knife Finishing Can be sanded, drilled and painted Use Interior and exterior SafetyUse only with good ventilation, away from heat, sparks and flames, and wear gloves and eye protection, plus suitable respiratory protection if ventilation is poor. Store both products in tightly closed containers in a cool, dry place, below 30°C. Refer to the Safety Data Sheet (SDS) for full details.
$63.02
![Roberts Quick-Repair Putty 88ml [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-putty-88ml-grey-2.png?v=1792410905&width=645)
Roberts Quick-Repair Putty in Grey is a ready-to-use floor repair filler for hiding gaps, nicks, scratches and fastener holes in laminate, vinyl, hybrid and engineered or timber floors, supplied in a handy 88ml squeeze tube. It suits both fresh installations and repairs to floors that are already down, and it can be used straight from the tube or blended with other Roberts shades to match your flooring.About the formulaAn acrylic-based putty that dries quickly and is made not to shrink back as it dries. It sands smoothly and can be painted over, so you can fine-tune the colour or finish once it has set. It is a low VOC product with a two-year shelf life, and the soft tube lets you squeeze out a controlled bead for neat, quick application.Where to use itIndoors: filling nail and screw holes during floor installation, closing small gaps between boards or planks, and touching up chips, dents and scratches on existing laminate, vinyl, hybrid and timber floors.Outdoors: not intended for outdoor use.Suitable surfaces include laminate flooring, vinyl flooring, hybrid flooring, engineered timber and solid timber floors. Grey is a mixable base shade, so test your colour match on an offcut or a hidden spot before committing to a visible repair.How to use itClean the area first so it is free of dirt, dust and grease. Knead the tube well for about 20 seconds, then snip the tip to suit the size of bead you need. Press the putty firmly into the gap or hole and smooth it level with the floor. Wipe any excess off the surrounding floor with a damp rag before it dries, because dried-on filler is much harder to remove. If you need a closer colour match, mix shades before applying. Once the putty has fully cured it can be sanded flush or painted if required.Important notesAlways choose or blend a shade that matches the lightest base colour of your floor. Store at room temperature and do not let the tube freeze, as freezing can affect performance. Cure and recoat times vary with bead depth, temperature and humidity, so allow the repair to cure fully before sanding, painting or walking on it heavily. Reseal the tube after use to keep the remaining putty usable.Specifications Brand Roberts Product Quick-Repair Putty (Model PC7728) Size 88ml tube (3 oz) Colour Grey Base Acrylic Application Squeeze tube, hand applied Finish Sandable and paintable VOC Low VOC Shelf life 2 years Use Interior flooring repairs SafetyIf it gets in your eyes, rinse with plenty of water. Keep out of reach of children and store the tube sealed at room temperature, away from freezing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
Gilly's Beeswax Filler Sticks are coloured wax sticks for repairing cracks, gaps and small holes in timber, supplied here as an assorted pack of six sticks in different wood tones. You pick the shade closest to your timber, work the wax into the damage and finish the surface, which suits furniture, cabinets, frames and general timber touch-ups.About the formulaThese are pigmented wax fillers made from pure beeswax, natural pigments and a natural hardener. Once set, the wax can be buffed to a fine finish and coated with most materials. The manufacturer says the colours can be blended, and leftover wax can be melted down and reused.Where to use itIndoors: filling nail holes, gaps, joins and cracks in furniture, cabinetry, frames and other timber items.Outdoors: the manufacturer does not publish outdoor performance data for this product, so it is best treated as a timber repair filler for interior and finished-furniture work.Suitable for most wood surfaces, in both soft and hard woods. It is aimed at damage wider or deeper than about 1mm. Very fine scratches and surface blemishes are better treated with a wax product made for that job.How to use itStart with a clean, dry surface and apply the filler to raw timber before any oil, wax or lacquer finish. Pick the stick closest to the timber, or melt two colours together to blend a custom match. Soften the wax with a soldering iron, a hot knife, or gentle heat from a heat gun or hairdryer. Take care, because extra heat can affect the surrounding finish. You can also soften a stick briefly in a microwave. Test in very short bursts, as it only needs to become malleable. Press the softened wax into the gap. For larger repairs, chip off the amount you need and melt it into the gap. Once the wax has firmed up again, scrape off the excess with a plastic spatula or an old card, then buff to a smooth finish. Important notesThe wax firms up quickly after application, typically within about 10 to 30 minutes depending on conditions. Rubbing a cold stick over a gap like a crayon works, but adhesion is better when the wax has been melted. Beeswax can ignite when overheated, so the manufacturer advises caution and says not to apply an open flame directly to the sticks. The product may contain traces of bee pollen and soy. If you plan to use it on a surface that will touch food, check suitability with the manufacturer first, as the coloured sticks are pigmented.Specifications Brand Gilly's Australia Product Beeswax Filler Sticks, Assorted Pack 6 sticks, 15g each (about 90g in total) Stick size About 83mm long x 15mm diameter Colours Pale brown (natural), orange/brown, mid brown, red/brown, dark brown, black (one of each) Base Beeswax with natural pigments and natural hardener Application Hand applied; melt or soften the wax, press into the gap, then scrape back and buff Firming time About 10 to 30 minutes, depending on conditions Use Timber repair, applied before the final finish Origin Made in Australia SafetyTake care when heating the wax, as molten wax can burn skin and beeswax can ignite at high temperatures. Keep it away from open flames and avoid overheating. Allow the wax to cool before handling. Store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$34.95
Protite Fibreglass Resin is a low styrene emission (LSE) polyester resin for repairing cracks, dents, holes and worn patches on boats, caravans, cars, trailers, gutters and more, supplied here in a 500g size. Mixed with catalyst hardener and used with fibreglass matting or cloth, it gives DIYers and tradies a strong, workable repair material with good adhesion and a consistent wet-out.About the formulaA polyester LSE resin designed for general repair work. Once catalysed it cures to a hard, sandable and paintable finish that resists shrinkage and UV exposure. The resin is a viscous liquid and contains styrene, so it has a strong aromatic odour while you work. It does not cure on its own: you need to add a catalyst hardener (sold separately). Protite also offers a repair kit that bundles the resin with catalyst, matting and application accessories.Where to use itIndoors: repairs to fibreglass, timber, metal and plastic items, models and workshop projects, provided you have good ventilation.Outdoors: caravans, boats, trailers, bikes and cars, plus downpipes, leaky gutters, metal roofs and rusted panels, as well as fibreglass surfboards, pools and tanks.Suitable materials include fibreglass, steel, iron, aluminium, timber, masonry, PVC and smooth polyester surfaces. Test an inconspicuous area first when working on other plastics.How to use itClean the damaged area and remove loose material, grease and dust. Sand the surface so the resin has a key to grip. Pour only the amount of resin you can use in one session into a clean mixing container, then stir in the catalyst hardener. The catalyst manufacturer's guide is 2.5 to 3ml per 100ml of resin on a cold day, or 1.5 to 2ml per 100ml on a hot day. Mix thoroughly with a flat stirring stick until the colour is even. Work the resin into the repair (with matting or cloth if needed) by dabbing or rolling it out slowly to avoid trapping air bubbles. Allow it to cure, then sand and paint as required. Weather, humidity, depth of resin and draughts all change the amount of catalyst you need.Important notesUncatalysed resin will not harden, and too little catalyst or a very thin application can leave the resin tacky or uncured. Too much catalyst makes it gel sooner than expected. The manufacturer indicates the mix starts to gel after about 30 minutes at 25°C, and heat or extra catalyst shortens this while cold or less catalyst lengthens it. Take care when using polyester resin over epoxy surfaces and check compatibility first. Cure times depend on temperature and the amount of catalyst used. Clean tools before the resin cures.Specifications Brand Protite Product Fibreglass Resin (LSE) Size 500g Model number PF-FR0500 Base Polyester resin, low styrene emission Catalyst Required, sold separately Application Hand applied after mixing with catalyst, dabbed or rolled out Finish Sandable and paintable Resistance UV and shrink resistant Use Interior and exterior SafetyUse outdoors or in a well-ventilated area. Wear suitable gloves, eye protection and protective clothing, and avoid breathing vapours. Keep away from heat, sparks and open flames. Store in a cool, dry, well-ventilated place out of direct sunlight and away from ignition sources and incompatible materials, with the lid closed and out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$26.18
![Selleys No More Gaps Timber Floors Gap Filler 380g [Baltic] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-more-gaps-timber-floors-gap-filler-380g-baltic-2.jpg?v=1792410739&width=645)
Selleys No More Gaps Timber Floors in Baltic is a flexible, wood-fibre gap filler made for sealing the gaps between tongue and groove floorboards, supplied as a single 380g cartridge. The Baltic tint is made to sit in lighter timber floors, so the repair blends in once it has been sanded and finished.About the formulaA water-based acrylic filler loaded with real wood fibre. The fibre helps the cured filler take stain better than a standard gap filler, and it sands back to a smooth, clean surface. It stays flexible to cope with the seasonal movement of floorboards and forms an airtight seal that helps keep out draughts, dust and pests. Baltic is tinted to suit pine, myrtle and alpine ash. Hardwood, Jarrah and Walnut tints are available separately for other timbers.Where to use itIndoors: gaps around and between tongue and groove timber flooring, and between timber panels and fittings such as skirting boards, architraves and benchtops.Outdoors: not suitable. This is an interior-only product.Suitable materials include timber flooring, timber panels and fittings, and engineered timber floors. The Baltic tint is the best match for pine, myrtle and alpine ash.How to use itMake sure the gap is clean, dry and free of dust. Cut the cartridge seal and nozzle to suit the width of the gap, fit the nozzle and load the cartridge into a caulking gun. Force the filler well into the gap, then press it in and smooth it off with a spatula, taking care not to drag filler back out of the joint. Scrape surplus filler off the timber surface with the spatula to cut down on sanding later, and wipe up any smears straight away with a damp cloth. Allow the filler to cure fully before sanding, staining, varnishing or painting. Wear a P1 dust mask when sanding.Important notesNot for exterior use. Not for gaps wider than 3mm in trafficable joints. Allow at least 24 hours to cure, and longer in cold or damp conditions. Uncured filler cleans up with water, while cured filler needs to be sanded or scraped off. Keep the cartridge stored above 5°C. Test stains and finishes on a small area first, as the final colour depends on the timber and the finish used.Specifications Brand Selleys Product No More Gaps Timber Floors Gap Filler Pack 1 x 380g cartridge Colour Baltic (suits pine, myrtle, alpine ash) Base Water-based acrylic with real wood fibre Application Cartridge, via caulking gun Full cure 24 hours Coverage About 18 m of 3mm bead per cartridge Sandable Yes Stainable Yes Paintable Yes Clean up Water (while uncured) Use Interior only SafetyAvoid prolonged skin contact and keep the product out of the eyes, and wash your hands after use. Wear a P1 dust mask when sanding the cured filler. Keep out of reach of children and avoid letting the product enter waterways. Store above 5°C. Refer to the Safety Data Sheet (SDS) for full details.
$21.33
Selleys Plastic Wood is a fast-setting, solvent-based wood filling cement for repairing holes, dents and chips in interior timber, supplied here in a 230g maple-coloured tin. It is a simple fix for furniture, skirting, architraves and other indoor joinery, and once set it can be worked much like the timber around it.About the formulaA solvent-based paste containing natural wood fibres, finished in a maple (tan) colour. It dries quickly to a hard finish that holds up to sanding, nailing and planing. Once dry it can be stained, varnished, painted or lacquered, so the repair can be finished in the same way as the surrounding wood. It is a rigid filler, so it is not designed for joints that move.Where to use itIndoors: filling nail holes, dents, chips and small cracks in furniture, doors, window frames, skirting boards, architraves and other interior woodwork.Outdoors: not recommended. The manufacturer rates this product for interior use only.Suitable materials include natural timber and wood veneer.How to use itStir the product thoroughly before use. Make sure the surface is clean, dry and free of loose material. Press the filler in with a putty knife and slightly overfill deeper holes so there is room to sand back flush. Do not fill deeper than 6mm in a single application. Let it dry fully before sanding, staining, painting or lacquering. Wipe the putty knife clean with methylated spirits. Press the lid on firmly after use and store the tin somewhere cool.Important notesNot suitable for exterior use. Not recommended where structural movement may occur, so use a flexible product for joints and gaps between surfaces. Work in a well-ventilated area. Colour is maple only, so test a small area first if you need to match a different timber tone, or plan to stain or paint over the repair.Specifications Brand Selleys Product Plastic Wood Filler Cement Size 230g tin Colour Maple Base Solvent-based, with natural wood fibres Application Putty knife Maximum fill depth 6mm per application Set speed Fast setting Clean up Methylated spirits Use Interior only SafetyThis is a highly flammable solvent-based product. Keep it away from heat, sparks, flames and other ignition sources, and avoid static discharge. It can irritate skin and eyes, and the vapours may cause drowsiness or dizziness. Use only in a well-ventilated area and avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.
$38.42
Turbo Builder's Bog is a trade quality, two part polyester filler for repairing damaged and rotted timber, supplied here in a 500ml can for builders, painters and capable DIYers. It sets to a hard, wood-like finish that you can sand, drill and paint, so it suits window sills, door frames and other jobs where replacing the timber is not practical.About the formulaA polyester-based filler paste that cures by a chemical reaction when mixed with the red hardener paste, rather than by drying out. Because of this, it shows no obvious shrinkage. You choose the working time by adjusting how much hardener you add within the range printed on the can, and the mix also sets faster in warm weather. As it sets it passes through a soft, cheese-like stage where it can be trimmed with a blade or a surform file. Shaping at this point saves a lot of sanding. It spreads smoothly, holds its shape on large fills without slumping, and bonds firmly to timber.Where to use itIndoors: filling holes, gaps and dents in architraves, skirtings, door frames and other timber trims before painting.Outdoors: repairing window sills, sashes, fascias, decks and door frames, including areas where the timber is partly rotten, once the soft material has been cleared back to sound wood.Suitable material is timber. It is designed as a timber repair filler and can be painted over once cured. Test first before using on other surfaces.How to use itMake sure the timber is clean, dry, unpainted, roughened and free of rot. Remove any soft or crumbling material first. Place the amount of filler you need on a clean, flat, non-absorbent surface, such as the plastic over-cap. Add the red hardener in the proportion given on the can, then mix thoroughly until the colour is completely even with no red or white streaks. As a guide from the manufacturer's mixing chart, 100g of filler with 2.5g of hardener gels in about 7 minutes at 22°C. Use less hardener if you need longer working time, particularly in warm weather. Press the mix into the repair with a putty knife or spatula, overfilling slightly. When it reaches the cheese-like stage, trim it to shape with a blade or surform. Allow about 30 to 60 minutes for a full cure, then sand and paint. Mix a small test batch first, because temperature and thickness change the set time.Important notesAlways follow the mix ratio on the can, because too little or too much hardener can affect the cure. Thick fills set faster than thin ones. Timber will still expand and contract with moisture changes, so good woodworking practice should still be followed around the repair. Mixed material generates heat as it cures. Do not leave mixed product in a pile or sealed container. Close the can tightly after use. Check the can and the supplied instructions for full details.Specifications Brand Turbo Product Builder's Bog timber repair filler Size 500ml can Colour Beige / buff paste Base Two part unsaturated polyester filler (cured with red hardener paste) Application Hand applied with a putty knife or spatula Gel time Adjustable by hardener amount; about 7 minutes in the 100g to 2.5g example at 22°C Full cure About 30 to 60 minutes Finishing Sandable, drillable and paintable Use Interior and exterior Country of manufacture New Zealand SafetyIt has a characteristic styrene odour. Use outdoors or in a well-ventilated area, avoid breathing vapours, and keep away from heat, sparks, open flames and other ignition sources. Keep the container tightly closed, out of reach of children, and stored in a dry place. Refer to the Safety Data Sheet (SDS) for full details.
$27.63
Selleys Aquadhere Durabond is a solvent-free, moisture-curing polyurethane wood glue for jobs that need more durability than a standard PVA can offer, supplied here in a 250ml bottle. It bonds timber to a wide range of other materials, copes with moisture and heat, and can be sanded, painted or stained once cured.About the formulaUnlike water-based PVA glues, Durabond cures by reacting with moisture in the air and the substrate. It gives a strong, water-resistant bond (not intended for permanent immersion) and is heat resistant up to about 140°C. The glue expands slightly as it cures, which helps it fill small gaps in imperfect joints. It also sands without clogging sandpaper or timber the way PVA glues can. Selleys notes it resists acids and most chemicals, unlike PVA-based glues.Where to use itIndoors: furniture making and repairs, timber joinery, cabinet repairs, sauna or other high-heat and high-moisture areas, repairing wooden tool handles, and general workshop fixes.Outdoors: planter boxes, steps off a veranda, window repairs, attaching a timber letterbox to a metal support frame, cubby or kennel repairs, and boat oar or interior panel repairs.Suitable materials include all timbers, MDF, metal, glass, concrete, masonry, ceramics and most plastics. It is not for polyethylene or polypropylene, and you should test other plastics first.How to use itSurfaces should fit closely and be clean, dry of dust and free of grease. At least one surface should be porous, as the glue needs moisture to cure. On very dry porous surfaces, wipe with a damp cloth for about a minute before bonding. Wear gloves, because the adhesive bonds to skin. Apply to the joint, bring the parts together within the working time and clamp them while the glue cures. Once cured, the joint can be sanded, and the surface can be painted or stained after sanding.Important notesWorking time is about 10 minutes, depending on temperature and humidity. Allow around 4 hours of clamp time. Full cure takes up to 24 hours, depending on humidity and how porous the material is. Do not apply below 5°C. Use may be restricted in very dry conditions because the glue needs atmospheric moisture to cure. It is not recommended for structural applications. The bond is waterproof but not for permanent water immersion.Specifications Brand Selleys Product Aquadhere Durabond Polyurethane Wood Glue Pack 250ml bottle Colour Amber, dries to a yellow opaque finish Base Solvent-free, moisture-curing polyurethane Application Bottle, applied by hand Working time About 10 minutes Clamp time About 4 hours Full cure Up to 24 hours Minimum application temperature Above 5°C Heat resistance Up to 140°C Use Interior and exterior SafetyUse with adequate ventilation. Store in a well-ventilated place with the container tightly closed and locked up. Refer to the Safety Data Sheet (SDS) for full details.
$19.76
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
Tarzan's Grip Wood Glue is a fast, dependable PVA timber adhesive built for everyday woodworking and repairs around the home and workshop. This 250mL bottle delivers a strong, lasting bond on a wide range of timbers, making it a reliable choice for cabinetry, joinery, furniture assembly and general carpentry jobs. The water-based PVA formula spreads smoothly, penetrates porous timber and sets to a tough, near-invisible bond line. Its extended working time gives you room to align and clamp pieces accurately before the glue grabs, while easy water clean-up keeps the job tidy with no harsh solvents. What it bondsIdeal for softwoods, hardwoods, plywood and MDF, and well suited to bonding porous materials to one another. Where to use itIndoor / Interior: furniture making and repair, cabinet and drawer assembly, joinery, trim and moulding, hobby and craft woodwork.Outdoor: this is an interior-grade wood glue and is not intended for fully weather-exposed or submerged applications. How to use it Make sure both surfaces are clean, dry and free of dust, grease and old finish. Apply an even coat of glue to one or both mating surfaces. Bring the parts together, align, and clamp firmly. Wipe away any squeeze-out with a damp cloth before it dries. Leave clamped until set, then allow full cure before stressing the joint. Important notesFor interior use only. Keep the cap closed between uses and store upright. Best results on clean, well-fitted joints with adequate clamping pressure. Specifications Brand Tarzan's Grip Product Wood Glue (PVA) Size 250mL Form Liquid Colour Light yellow Base Water-based PVA Density 1.05 g/cm³ pH 3.5 - 4.5 Clean up Water (while wet) Suitable for Softwoods, hardwoods, plywood, MDF Use area Interior SafetyAvoid eye contact and repeated or prolonged skin contact, and avoid inhaling mist or vapour. Wash hands after use and keep away from food and drink. Store in a cool, dry, well-ventilated place out of direct sunlight and away from heat or ignition sources. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$33.75
Loctite EA 9235 (Five Minute E-Pox-E, item EFQ5) is a fast-acting two-part epoxy that mixes resin and hardener in equal parts to form a tough, rigid, high-strength bond in about five minutes. Supplied in a dual-barrel syringe that dispenses both components in the correct 1:1 ratio every time, it is ideal for fast permanent repairs and multi-piece projects across a wide range of household, workshop and trade materials. Once cured it resists water and most common solvents, and can be sanded, drilled and machined. It can also be used as a versatile filler for gap filling, surface repairs and laminating. Bonds: metal, glass, ceramic, china, tile, stone, concrete, wood, fibreglass and most rigid plastics. Where to use it Indoor: repairing ceramics, china and glassware, fixing tools and toys, bonding tiles, and general household and hobby repairs. Outdoor: bonding stone, concrete and masonry, plus garden and workshop repairs. Not recommended for continuously wet areas or prolonged water immersion. How to use 1. Make sure surfaces are clean, dry and free of oil, wax, paint and rust. Roughen smooth surfaces by sanding for a stronger grip. 2. Remove the plug and cut the syringe tip at the marked opening. Stand the syringe upright and press the plunger gently to expel any air. 3. Depress the double plunger to dispense equal parts of resin and hardener onto a disposable surface, then mix thoroughly for about one minute. 4. Apply to both surfaces within one to two minutes of mixing and press together. Support the join for around 10 minutes. 5. Usable strength is reached in about 1 hour and the bond fully cures in 24 hours. Wipe the tips clean and replace the plug for storage. Clean uncured adhesive with acetone before it sets. Cured adhesive can be carefully cut away with a sharp blade. Important notes Not recommended for polyethylene, polypropylene, nylon, non-stick coatings or flexible materials. Not suitable for potable (drinking) water systems, prolonged water immersion, or short-term heat above 150°C. Apply between 4°C and 35°C. Specifications Part number Loctite EA 9235 / EFQ5 Size 25ml dual syringe Chemistry Two-part epoxy (epoxy resin / polymercaptan hardener) Mix ratio 1:1 by volume Set time Approx. 5 minutes Usable strength Approx. 1 hour Full cure 24 hours Cured colour Clear amber Hardness 80 Shore D Service temperature -23°C to 49°C continuous (up to 150°C intermittent) Water resistant Yes Sandable / machinable Yes Paintable No Shelf life 24 months unopened SafetyContains epoxy resin and polymercaptan/amine hardeners. Causes skin and eye irritation and may cause an allergic skin or respiratory reaction. Wear gloves, work in a well-ventilated area and avoid breathing vapours. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$33.75
Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gorilla Ultimate for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Furniture build and repair Edge bonding and laminations Cabinetry and joinery where water resistance is valued Suitable surfaces The adhesive works well on the following surface types when properly prepared: Hardwoods and softwoods Plywood and MDF Veneers and end grain with correct technique Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured. Temperature and environmental performance Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$25.20
Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.
$8.50
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$5.05
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$8.05
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$25.48
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$22.35
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$44.00
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-more-gaps-timber-floors-x-380g-walnut-2.jpg?v=1792406166&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
SANDING BLOCKS offer optimal sanding results on flat, contoured and irregular shapes. • Flexible, to conform to contours and irregular shaped objects. • For sanding and cleaning metal, wood, plaster, plastic, fibreglass etc. • Can be used for wet or dry sanding. • Rinse with water to clean.
$2.05
Handy for removing old glue, paint, silicone, etc
$4.50
Handy for removing old glue, paint, silicone, etc
$3.50
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$71.95
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$6.07
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$135.00
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$17.04
Ideal for filling holes, cracks, dents, chips and grain imperfections on interior timber surfaces. Can be nailed or planed. Easy to sand, sets to a hard finish and is highly crack resistant. Filling blade included For use on: Timber (INTERIOR) Fill depth: Up to 6mm Dries in: 2-3 hours Ready to use: YES Colour: Produces a pine finish that can be tinted or stained. Application Tips • Surface to be filled should be clean and dry with no loose or powdery material. • Using the attached filling blade press filler in firmly and remove excess. * Allow drying for 2-3 hours in 2-3mm thin applications, depending on humidity. Allow longer drying if painting with solvent-based coatings (24 hours minimum) or for deeper applications. • Sand with fine sandpaper. For a perfect finish after initial sanding back, apply a thin coat of filler, allow to dry and sand lightly with very fine (400 grit) sandpaper before staining or coating. • When tinting or staining, the final colour is not achieved until the varnish is applied. • Prime metals (eg, nail heads) before applying filler. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. I want a filler that matches the colour of the timber I am repairing. What should I use? A. The best idea is to custom tint/stain a filler to match your timber, rather than buy a pre-tinted colour filler. This allows you the flexibility to adjust to the shade you require, rather than having the colour dictated by the manufacturer. For interior timbers, use Polyfilla Timber Filler. If you require a wood filler that can be exposed to the elements, use Polyfilla Exterior Timber, which flexes with the natural movement of wood. Note: When tinting /staining, the final colour is not achieved until a varnish is applied. It is worth testing first on an off-cut or inconspicuous area to see if the correct colour match is achieved.
$22.74
A durable, ready to use, acrylic based, flexible filler for filling cracks, holes, dents and splits in weatherboards and other exterior woodwork such as decking and fencing. Unlike more rigid woodfillers, it flexes with the natural movement of wood and will not crack, split or fall out. Can be stained, clear-finished, painted, nailed, screwed, sanded or planed. For use on: Timber (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 450g and ^2kg Colour: Dries to a pine colour NOTE: Not for permanently wet areas or joints between weatherboards, floorboards, panels etc. • Ensure surfaces are clean and dry. • Remove any rotten wood and fix split timber firmly before filling. Priming is unnecessary. • Apply firmly with filling blade. • Allow to dry (*2–3 hrs in thin 2–3mm applications depending on humidity). • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • Sand back and paint with with a quality exterior water or oil-based paint, or stain and clear finish. • For a smoother finish allow filler to dry, sand back and apply a very thin coat of filler. Allow this to dry then sand lightly with fine (>300 grit) sandpaper before painting or vanishing. • Protect from rain until painted over. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$22.49
A durable, ready to use, acrylic based, flexible filler for filling cracks, holes, dents and splits in weatherboards and other exterior woodwork such as decking and fencing. Unlike more rigid woodfillers, it flexes with the natural movement of wood and will not crack, split or fall out. Can be stained, clear-finished, painted, nailed, screwed, sanded or planed. For use on: Timber (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: Dries to a pine colour NOTE: Not for permanently wet areas or joints between weatherboards, floorboards, panels etc. • Ensure surfaces are clean and dry. • Remove any rotten wood and fix split timber firmly before filling. Priming is unnecessary. • Apply firmly with filling blade. • Allow to dry (*2–3 hrs in thin 2–3mm applications depending on humidity). • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • Sand back and paint with with a quality exterior water or oil-based paint, or stain and clear finish. • For a smoother finish allow filler to dry, sand back and apply a very thin coat of filler. Allow this to dry then sand lightly with fine (>300 grit) sandpaper before painting or vanishing. • Protect from rain until painted over. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$79.79
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$23.38
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$28.08
Sandable Paintable Ready mixed Weather resistant Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home. Sandable and paintable, it enables a smooth finish.
$24.94
Partix Multipurpose Filler Powder This product is ideal for filling cracks, holes and gaps inside the home. It is strong and can be easily sanded to a smooth finish ready for painting. When dry, it can be nailed or screwed without splitting or breaking. SUITABLE FOR Interior repairs to plaster, brick, plasterboard, masonry and timber. For repairs where movement occurs, use Parfix Gap Filler. PREPARATION Ensure surfaces are clean, dry and free from dust and loose material. Glossy surfaces should be roughened with sandpaper to provide key. MIXING Add 2½ parts of Parfix Multi-Purpose Filler to 1 part water (by volume) and mix thoroughly into a smooth paste with a clean filling knife. Once mixed, stays workable for up to 45 minutes. Do not add water to extend working time. 4 Contamination with dried filler will shorten the working time. APPLICATION Press filler into crack with a flexible filling blade (overfilling slightly to allow for sanding back) then smooth off. Wait 3-4 hours for filler to dry before sanding with a medium grade sandpaper Use a damp sponge to wipe away dist CLEANING Clean tools with water and reseal pack after use. Store in a cool, dry place. PAINT PREPARATION Before painting, apply a suitable primer/undercoat
$14.75
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$26.67
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$15.50
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
You have seen 96 out of 96 products
Fill and rebuild timber with stainable or paintable finishes. Great for furniture, frames and trims. Select fast set for small patches or longer open time for shaping. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
