![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time." You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.
$10.29 - $239.00
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$25.37
Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.
$8.70 - $54.81
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
$102.00
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming
$8.77 - $86.00
Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.
$70.50
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$13.37
Boyle Mosaic Craft Adhesive Glue Paste 120 g is a reliable ready to use craft adhesive paste for mosaic and small decor pieces chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 120 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Boyle Mosaic for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Boyle Mosaic Craft Adhesive Glue Paste 120 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Mounting glass tesserae and small tiles to bases Decorating frames, pots, and plaques Craft classes and school projects Suitable surfaces The adhesive works well on the following surface types when properly prepared: Terracotta and ceramic bases Primed timber Card and board Glass and stone pieces Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of workable for extended craft sessions. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial grab holds pieces in place while you continue working. Allow to dry fully before grouting or moving finished items. Temperature and environmental performance Use in dry indoor conditions for best results. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe away fresh squeeze out with a damp cloth. Wash brushes in warm soapy water. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close lid firmly after use to prevent skinning. Store at room temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$17.97
![Bostik Blu Stik Glue Sticks 35g [10 Pack]](http://gluesaustralia.com.au/cdn/shop/files/3247a52b-3527-4297-825a-a050176be4e8_d6fe2015-9cbc-4930-b3d1-683224070b7d.png?v=1760577211&width=645)
Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 10 glue sticks x 35 g each.
$33.50
Bostik Blu Stik is the glue stick that solves the problem every teacher and parent knows: children cannot see where they have already glued. It goes on blue, so coverage is obvious, then dries completely clear so the finished work looks clean. This listing is a five pack of 21g sticks, a handy size for younger hands and for topping up a pencil case, craft caddy or classroom tub without paying for glue that dries out before it is used.The formula is solid, solvent free and non-toxic, which is why it has been a classroom standard in Australia for decades. It is acid free, so it will not yellow photographs or corrode the paper underneath over time, and the non-wrinkle characteristic keeps lightweight paper flat instead of buckling as it dries. The twist-up base lets you expose only as much glue as you need, and the cap seals tightly to stop the stick drying out between uses.Where to use itIndoors Cut and paste activities, worksheets and school projects Scrapbooking, journaling and album work Card making, collage, invitations and paper craft Dry mounting photographs and artwork General office and home stationery jobs on paper and light card OutdoorsNot suitable. This is a water soluble stationery adhesive with no moisture or weather resistance, so anything heading outdoors needs a different product.What it bondsPorous materials, including paper, cardboard, photographs, tissue and crepe paper, and lightweight fabric. Surfaces need to be clean and dry.How to use Check both surfaces are clean and dry. Remove the cap and turn the base until a small amount of glue protrudes. Expose only what you need. Apply an even layer to one surface. The blue colour shows exactly where you have covered. Press the two surfaces together firmly. Turn the base back to retract the glue and recap straight away. Tip: a stick left uncapped and dried out can usually be revived by standing it in warm water for a few minutes rather than being thrown away.Important notes For lightweight bonding only. Not suitable for heavy duty or structural repairs. Not suitable for non-porous surfaces such as metal, glass or most plastics. No water resistance. Keep finished work dry. Always recap after use. Store between 5°C and 30°C, away from direct sunlight. Contains corn starch. Free from wheat, gluten, flour, egg and nut ingredients, though repeated or prolonged contact may cause an allergic reaction in susceptible people. Specifications Brand Bostik Product Blu Stik Pack 5 x 21g sticks Type Solid stick stationery adhesive Colour Blue on application, dries clear Solvent content Solvent free Acid free Yes Finish Non-wrinkle, clear Clean up Warm soapy water Suitable surfaces Paper, cardboard, photographs, light fabric Storage 5°C to 30°C, away from direct sunlight Compliance Tested to AS/NZS ISO 8124.3 (Safety of Toys, migration of certain elements) SafetyIt is still an adhesive rather than a toy. Keep it away from very young children, avoid eye contact and do not eat it. Residue on skin, clothing and surfaces washes off with warm soapy water. Refer to the Safety Data Sheet (SDS) for full details.
$20.86
Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle
$16.45
High strength, water based adhesive for carpet and cork Dunlop Multipurpose Carpet & Cork Adhesive is a water based, high strength adhesive designed for installing smooth or textured backed carpets and cork tiles. It delivers excellent wet grab and reliable bond on prepared subfloors. Suitable Surfaces Concrete Marine plywood Fibre cement sheet Key Features Water based and low odour High initial grab for reduced slippage Repositioning window up to 60 minutes Install immediately into wet adhesive for most carpets For cork or stiff backings, allow 10 to 15 minutes tack time before laying Coverage Approx. 2.5 m² per litre with a 3.2 mm V notch trowel Approx. 3.5 m² per litre with a 2.4 mm V notch trowel Application Ensure subfloor is dry, smooth, clean and protected from moisture. Prime highly porous concrete or timber before applying. Spread an even coat with the recommended V notch trowel. Lay carpet into the wet film. For cork or stiff backings, wait until the adhesive becomes tacky. Roll in both directions with a suitable drum roller to ensure full transfer. Set and Traffic Times No foot traffic for 24 hours Heavy traffic after 48 hours Avoid water and cleaning for 48 hours Clean Up Clean tools immediately with warm soapy water Remove dried residue with mineral turps Storage Shelf life up to 12 months in an unopened container stored at around 23°C. Good To Know Apply between 10°C and 30°C. Coverage varies with subfloor condition and trowel technique.
$54.95
Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.
$27.85
Earl’s MiracleWipes – Innovative, Professional-Grade Cleaning Wipes Meet the jobsite and workshop essential that takes on the messes others can’t. MiracleWipes® are purpose-built to remove tough contaminants like oil-based paint, latex paint, epoxy, spray paint, stain, grease, oils, adhesives, ink, and grime from hands, tools, and surfaces. The unique absorbent-lock design grabs and traps residue so it doesn’t smear, while the low-solvent formula is surface and skin safe when used as directed. Dual-texture wipes (scrub on one side, smooth on the other) give you the control to lift heavy build-up then finish clean. Seeing is believing! Why You’ll Love It Removes paint & epoxy fast: Cuts through wet and semi-cured paints, epoxies, stains, grease and more. Absorb & lock technology: Traps mess in the wipe to reduce smearing and re-depositing. Dual-texture performance: Textured side agitates; smooth side finishes clean. Low solvent, professional grade: Powerful on mess, considerate on common jobsite materials. Surface & skin safe: Designed for hands, tools, and non-porous surfaces when used as directed. Large wipe size: 12" × 6" sheets give you more cleaning area per pull. Clean, no-rinse finish: Leaves no heavy, oily residue; dries quickly. Smart canister: One-at-a-time dispense with a tight snap-seal lid to keep wipes fresh. Where It Works Ideal for use on: Hands & skin: Great for cleanup after painting or epoxy work (avoid eyes, mouth, and broken skin). Tools & equipment: Brushes, rollers, spray guns, trowels, mixers, blades, scrapers. Common surfaces: Metals, coated plastics, laminates, sealed wood, glass, tiles, stone benchtops (sealed), vinyl & PVC. Prep before painting: Wipe down to remove dust, light oils, fingerprints and shop grime prior to coating. Always test on an inconspicuous area first. Not recommended for unfinished leather, delicate textiles, or uncured high-gloss finishes. How To Use Open the snap-seal lid and pull one wipe through the dispenser. Use the textured side first to loosen paint, epoxy, grease, or grime. Flip to the smooth side to lift away residue and finish clean. For stubborn spots, hold the wipe against the area briefly, then wipe again. Repeat with a fresh wipe if needed. Close the lid firmly after each use to prevent drying out. Dispose of wipes in the bin—do not flush. Pro Tips Epoxy cleanup: Tackle while epoxy is wet or green for fastest results. Surface prep: After wiping, allow to air dry, then apply coatings per product directions. Electronics & sensitive parts: Power down first; use a lightly damp section of the wipe and avoid pooling liquid. Frequently Asked Questions Will MiracleWipes remove fully cured epoxy?They excel on wet and semi-cured residues. Fully cured epoxy typically requires mechanical removal; wipes help with final cleanup. Are they safe on skin?Yes when used as directed on hands. Avoid contact with eyes and broken skin. Rinse with water after heavy use if desired. Do they leave residue before painting?The low-residue formula dries quickly. For best coating adhesion, allow the surface to dry or give a quick final wipe with a clean, dry cloth. Can I use them on automotive paint or delicate finishes?Test first in a hidden spot, especially on fresh or uncured coatings. Are the wipes flushable?No. Dispose of used wipes in general waste. What’s In The Pack Count: 90 pre-moistened, dual-texture wipes Wipe size: 12" × 6" (approx. 30.5 × 15.2 cm) Dispenser: Resealable snap-seal canister Storage & Handling Keep lid closed to prevent drying. Store upright in a cool, dry place. Keep out of reach of children. Use in a well-ventilated area. Do not ingest. Do not flush. Specifications Brand Earl’s Product MiracleWipes® – Innovative Cleaning Wipes Primary Use Removal of paint (oil & latex), epoxy, spray paint, stain, grease, oils, adhesives, inks, and grime Wipe Construction Dual-texture (scrub + smooth), high-absorbency lock design Wipe Size 12" × 6" (approx. 30.5 × 15.2 cm) Pack Size 90 wipes per canister Solvent Level Low solvent Skin/Surface Safety Surface & skin safe when used as directed Residue Low-residue, fast-dry Country of Manufacture Made in the USA Dispensing One-at-a-time pull through snap-seal lid Disposal General waste only; do not flush Suggested Applications Trade & DIY paint cleanup (rollers, brushes, sprayers, trays) Epoxy projects (boats, composites, woodwork, crafts) Auto & equipment maintenance (oils, grease, grime) Site prep and tidy between coats Workshops, garages, construction, facilities maintenance
$32.87
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
$8.13
![Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikaflex-111-stick-seal-1-part-adhesive-sealant-290ml-white-2.jpg?v=1792406518&width=645)
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.98
![Sika Sikaflex 118 Extreme Grab 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
![Sika Sikaflex 118 Extreme Grab 290ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikaflex-118-extreme-grab-290ml-white-2.jpg?v=1792406480&width=645)
Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use. Very high initial grab Fixing of heavy objects without temporary fixation Good workability Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors* Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking Packaging 290 ml cartridge, 12 cartridges per box Colour White Composition Silane terminated polymer Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging. Density ~1.40 kg/l Technical Information Shore A hardness ~50 (after 28 d) Tensile strength ~2.2 N/mm2 Tear propagation resistance ~10.0 N/mm Service temperature −40 °C min. / +80 °C max. SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive. For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush. Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours). For more detailed advice and instructions contact Sika Technical Services. Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically. For cleaning skin use Sika® Hand Wipes.
$31.22
Selleys Liquid Nails Exterior: The Builder's Choice for Durable Outdoor Bonds Key Features Adheres up to 3 tonnes per m² after just 4 hours on timber Water, heat, and UV-resistant Long-lasting bond that won't crack or go brittle Fast and easy water clean-up Compliant with Australian Standard AS 2329(1999) and Green Building Council VOC limits Suitable Materials This adhesive is ideal for the following materials: Timber Plasterboard MDF LOSP Treated Timber Concrete Masonry Plastics (pre-test for compatibility) Tiles Glass Ceramics Directions for Use Follow these simple steps for optimal performance: Ensure surfaces are clean and free from grease or loose particles. Cut cartridge tip, fit nozzle, and cut to 5mm opening. Apply adhesive along the material's length or in beads on flat surfaces. Press pieces firmly together, securing with fasteners or clamps. Allow to set for a minimum of 4 hours before removing any temporary fasteners. Limitations Not suitable for use on PFTE, PE, or PP. Cleaning & Safety Clean up is easy with warm soapy water or a damp cloth for wet adhesive, and a scraper or sandpaper for dried adhesive. Product Specifications Available in 350g cartridges, in white color, and uses Self-crosslinking acrylic technology.
$12.00
![Roberts Quick-Repair Floor Putty 88ml [Tan] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-tan-2.png?v=1792410981&width=645)
Roberts Quick-Repair Floor Putty in Tan is a ready-to-use acrylic putty for hiding gaps, nicks, scratches and fixing holes in laminate, hybrid, vinyl and engineered timber floors, supplied in an 88ml squeeze tube. It works as a quick touch-up fix for existing floors and as a finishing step during installation, and the colour can be used straight from the tube or blended with other Roberts putty shades to match your floor.About the formulaAn acrylic-based putty that is ready to use with no mixing. It dries quickly without shrinking, so the repair stays level with the surrounding surface. Once dry it can be sanded smooth or painted over. It is a low VOC formula and has a two-year shelf life.Where to use itIndoors: filling nail and screw holes during floor installation, and repairing chips, nicks, scratches and small gaps on floors that are already laid, including around joins and transitions.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, hybrid and vinyl flooring (plank and tile) and engineered timber flooring.How to use it Make sure the area is clean and free of dust and debris. Choose the Tan shade on its own, or mix it with other Roberts putty colours to get the closest match to your floor. Knead the tube well for at least 20 seconds before use. Cut the tip to suit the size of bead you need and press the putty into the damaged area. Spread it into the gap, nick or scratch with a putty knife so it fills evenly. Wipe away excess straight away with a damp rag and do not let it dry on the surrounding floor. Allow about 30 minutes to dry. The dried repair can be lightly sanded or painted if needed. Important notesColour match depends on your floor, so test a small hidden spot first and blend shades if needed. Store at room temperature and do not let the tube freeze, as freezing can affect performance. This is not a structural or waterproof repair product. For large areas of damaged flooring, replace the affected boards or planks.Specifications Brand Roberts Product Quick-Repair Floor Putty (model PC7730) Size 88ml squeeze tube Colour Tan Base Acrylic Application Squeeze tube, spread with a putty knife Dry time About 30 minutes Finish Matte Shelf life 2 years Use Interior floors SafetyAvoid contact with eyes and skin. If it gets on skin, wash with soap and plenty of water. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Brown] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-brown-2.png?v=1792410967&width=645)
Roberts Quick-Repair Floor Putty in Brown is a ready-to-use acrylic filler for hiding gaps, nicks, scratches and fastener holes in laminate, hybrid, vinyl and engineered timber floors. It comes in an 88ml squeeze tube, so it suits small touch-ups during an install or repairs to a floor that is already down. The brown shade can be used on its own or mixed with other Roberts Palette putty colours to match your floor.About the formulaThis is a water-based acrylic putty with a thick paste consistency. It is ready to use straight from the tube and is made to dry quickly without shrinking back out of the repair. Once dry it can be sanded or painted. The manufacturer also describes it as low VOC and gives it a two-year shelf life.Where to use itIndoors: filling nail and screw holes during floor installation, patching chips and scratches on existing laminate, vinyl or engineered timber floors, and closing small gaps at board edges.Outdoors: not intended for outdoor use. It is listed for interior flooring repairs only.Suitable materials include laminate, hybrid and vinyl flooring (including LVP and LVT), engineered timber and wood flooring. Test the colour in a small, hidden spot first, because the shade shifts a little as the putty dries.How to use itClean the damaged spot and make sure it is dry and free of dust. Knead the tube for at least 20 seconds to mix the putty. Squeeze a little onto the damage and work it into the nick, scratch or hole with a putty knife. Wipe the excess off the surrounding floor with a damp rag before it dries. If the colour is not quite right, blend two shades together before applying. Once dry, sand lightly if needed. The putty can be painted over for further colour options. Wash tools and hands with soap and water.Important notesAlways use the lightest base colour of your floor as the starting point for colour matching, and let a test patch dry completely before judging the match. The manufacturer lists a dry time of about 30 minutes, but this depends on temperature, humidity and how thick the fill is. For best results, store the tube at room temperature and do not let it freeze, as freezing may affect performance. This putty is made for flooring repairs and is not a structural filler or an adhesive.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range) Model number PC7725 Size 88ml tube Colour Brown Base Acrylic Application Squeeze tube, applied by hand or with a putty knife Dry time About 30 minutes (manufacturer listing) Finish Matte once cured; can be sanded, painted or stained Clean up Soap and water Shelf life 2 years Use Interior flooring SafetyWear gloves and eye protection when working, and make sure the area is ventilated. If it gets on skin, wash straight away with soap and plenty of water. Keep out of reach of children and keep the lid closed when not in use. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $11.03
Glitz Cleaning Vinegar Natural Eco Multi Purpose Cleaner 2L Make everyday cleaning simple with this powerful plant based vinegar cleaner. It cuts through grease, soap scum, water marks and light mineral deposits while leaving hard surfaces streak free. Ideal for kitchens, bathrooms, windows and floors, all in one generous 2L value pack. Why you will love it Natural cleaning power that tackles grime without harsh chlorine or ammonia. Streak free finish on glass, stainless steel and glossy tiles. Deodorises bins, laundry and pet areas with a fresh, clean scent. Concentrated value that you can use neat for tough spots or dilute for everyday mopping. Family friendly fragrance free formula suitable for regular cleaning. Eco mindful choice in a recyclable bottle. Where to use Kitchen benches, splashbacks and sinks Cooktops and stainless steel appliances Showers, taps, tiles and grout Windows, mirrors and glass doors Floors including sealed vinyl, sealed timber and tiles Laundry deodorising and general wipe downs Not recommended on Natural stone such as marble, limestone, travertine or unsealed granite. Avoid use on waxed or oiled timber, unfinished metals, electronics and any surface that is not water safe. Always spot test in a hidden area first. How to use General spray and wipe: Add to a trigger bottle. Light soils 1 part vinegar to 3 parts water. Spray, wipe clean, then dry with a lint free cloth. Glass and mirrors: Dilute 1 part vinegar to 4 parts water. Spray lightly and polish dry. Bathrooms: Use neat on soap scum and tapware. Apply, leave 2 to 3 minutes, scrub if needed and rinse well. Dry metal surfaces after rinsing. Floors: Add 1 cup to a 5L bucket of warm water. Mop and allow to air dry. Deodorise: Lightly mist bins or laundry tubs, then rinse or wipe after a few minutes. Tips for best results Do not mix with bleach or products containing bleach. Rinse natural rubber and metals after contact. Use microfiber cloths for a streak free finish. Product details Brand Glitz Product Cleaning Vinegar Natural Eco Multi Purpose Cleaner Size 2L Format Ready to use or dilute as directed Fragrance Fragrance free with mild vinegar scent Surface compatibility Glass, stainless steel, ceramic, enamel, chrome, sealed tiles, sealed timber, vinyl Bottle HDPE recyclable Safety Keep out of reach of children and pets. Avoid contact with eyes and prolonged skin contact. Do not ingest. Do not mix with other chemicals. Refer to the Safety Data Sheet (SDS) for full details. Frequently asked questions Can I use it on stone benchtops? No. Acids can etch natural stone. Use a stone safe neutral cleaner for marble, limestone, travertine or unsealed granite. Is it safe for stainless steel? Yes for quick wipe downs. Spray onto a cloth, wipe, then buff dry. Always rinse and dry taps and fittings. Can I use it in a steam mop? Check the appliance instructions. If additives are not recommended, use the floor dilution in a regular bucket and mop instead. What is included 1 x Glitz Cleaning Vinegar Natural Eco Multi Purpose Cleaner 2L Shipping and pickup Fast dispatch Australia wide from our Melbourne warehouse. Click and Collect available on request. Contact us to arrange a pickup time.
$3.89 $3.29
Get pro level finishes without the fuss. Gyprock CSR Less Mess Joint Compound is a pre mixed, easy sanding compound that helps you achieve smooth, paint ready walls with less splatter and minimal clean up. The handy 2.25kg tub is perfect for repairs, patching, jointing, and touch ups around the home or on site. Why you will love it Pre mixed convenience that is ready to use straight from the tub Less mess formula that helps reduce splatter and clean up time Easy to apply, easy to feather, and easy to sand smooth Low shrinkage for fewer repeat passes Paintable finish that accepts most interior paints Great for joints, screw head covering, corner repairs, and small patches Best suited for Interior plasterboard joints and repairs Skim coating small areas to blend texture Covering fasteners and minor cracks DIY touch ups and trade maintenance work How to use Surface prep: Ensure the area is clean, dry, dust free, and sound. Remove loose material and lightly scuff glossy paint. Application: Stir gently. Apply with a broad knife or trowel in thin, even coats. Feather edges well. Drying: Allow each coat to dry fully before recoating. Dry time varies with film thickness, temperature, and humidity. Sanding: Sand lightly with fine paper for a smooth finish. Remove dust before painting. Paint: Seal with a suitable primer then finish with your chosen interior paint. Tips for a flawless finish Work in thin passes rather than one heavy fill Keep your knife clean and slightly flexible for smooth feathering Use a dry sanding block or pole sander and avoid over sanding For deeper holes, build up in multiple coats Frequently asked questions Is it sandable and paintable? Yes. Once fully dry, sand lightly and prime before painting. Can I use it on previously painted walls? Yes, provided the paint is sound, clean, and lightly keyed. Is it suitable for wet areas? Use in dry interior spaces. For wet areas, follow local building guidelines and use appropriate systems. Specifications Brand Gyprock CSR Product Less Mess Joint Compound Pack size 2.25kg tub Colour Off white Use Interior plasterboard jointing and patching Cleanup Water while wet Finish Sandable and paintable Storage Reseal tightly. Store cool and dry. Do not allow to freeze. Good to know Coverage varies with joint size, substrate, and application method Dry times depend on thickness, temperature, and humidity Always test on a small area when working over sensitive or unknown coatings Safety Use in a well ventilated area Avoid breathing sanding dust. Wear a suitable mask and eye protection Keep out of reach of children Why buy from Glues Australia Fast dispatch Australia wide Careful packaging to protect your order Local support when you need advice
$35.43 $29.04
Selleys Liquid Nails Direct Stick Liquid Nails Direct Stick is a high strength polyurethane flooring adhesive designed for timber strip flooring and parquetry. Its semi rigid formula delivers a strong bond that helps reduce cupping and rafting. A controlled foaming action fills minor gaps. Fast cure means most floors can be sanded the next day to keep your project moving. Key Features High strength bond for timber flooring Semi rigid formula to help reduce cupping and rafting Foaming action fills small gaps and irregularities Fast cure so you can sand the next day Easy application with a strip flooring or parquetry trowel Where It Works Timber strip flooring Parquetry installations Interior floors on suitable, dry substrates Technical Details Technology Polyurethane adhesive Cure time Overnight under normal conditions. Sand and finish the next day. Application temperature 10°C to 30°C Coverage 2 m² per 1 L using the correct trowel 20 m² per 10 L using the correct trowel Clean up Protect adjacent finishes. Wipe fresh adhesive from surfaces before cure. Important Information Apply with a strip flooring or parquetry trowel to achieve stated coverage. Floors can usually be sanded the next day after proper cure. Protect surrounding finishes from expansion during foaming. Limitations Not suitable for wet or damp substrates. Avoid application below 10°C. Directions for Use Prepare the surface. Ensure substrates are clean, dry, sound, and free from dust, oil, and contaminants. Apply adhesive. Use the correct strip flooring or parquetry trowel. Spread adhesive evenly within the working time. Lay flooring. Place boards or parquetry into the wet adhesive. Press firmly to ensure full contact and adhesive transfer. Allow to cure. Leave to cure overnight under recommended conditions. Finish. Sand and finish the floor as required once the adhesive has cured. Good to Know Semi rigid bond helps manage seasonal timber movement. Foaming action assists with minor surface irregularities and gap filling. For best results, follow timber flooring manufacturer guidelines and site preparation standards. Available sizes: typically 1 L and 10 L tubs. Check current availability on this page before ordering.
$14.48
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.
$89.23
Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned. Why you’ll love it Exterior-grade flexibility: absorbs movement and vibration without cracking. Non-shrink & non-sink: holds profile and edge detail after cure. Won’t fall out: engineered adhesion for long-term durability. Ready to use: straight from the tub — no mixing, no mess, no waste. Paintable: achieves a seamless, colour-matched finish once dry. No VOCs: low odour, solvent-free formula. Interior / Exterior: versatile enough for both. Proudly Australian: made and owned in Australia. Where it works Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates: Timber: decks, window frames, trims, fascia, general carpentry repairs. Masonry: brick, block, render and patching mortar-like defects. Plasterboard: exterior-exposed linings under cover and general patching. Metals & gutters: non-structural filling and profiling (clean, sound, free of rust). Around pipes & penetrations: neat, gap-free finishing before painting. Glass & surrounds: edge repairs and feathering prior to topcoating. Ideal projects Rebuilding weathered or rotten timber edges before repainting. Filling cracks and surface imperfections in rendered walls. Profiling and feathering joints and transitions for a paint-ready finish. General exterior maintenance where a flexible, paintable filler is essential. Directions Surface Preparation Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound. Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required. For best mechanical key, lightly abrade glossy surfaces and remove dust. Application Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use. Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate. Build up in thin layers for deep repairs, allowing each layer to firm before adding the next. For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing. Finishing & Painting Allow to dry fully. Dry time varies with film thickness, temperature and humidity. Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat. Use quality exterior paints for weather-exposed areas. Clean-Up & Storage Clean tools and splashes with water while wet. Reseal immediately after use to minimise skinning and reduce waste. Store upright with lid sealed. Do not allow contents to dry out. Good to know Formulation is unaffected by normal temperature swings and resists cracking with vibration. Designed for exterior flexibility yet also suitable for interior touch-ups. For best results on deep voids, fill in multiple light applications rather than one heavy pass. Specifications Brand Earl’s Product MulTflex® Exterior Flexible Filler Type Single-pack, ready-to-use flexible filler & adhesive Use Interior / Exterior Paintable Yes, once fully dry VOC Content No VOCs (as supplied) Shrink / Sink Non-shrinking, non-sinking Flexibility Resists cracking with vibration and movement Clean-Up Water (while wet) Substrates Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass Finish Satin-smooth when tooled with a wet knife or brush Packaging Ready-to-use tub Country of Origin 100% Australian made & owned Limitations Do not apply to unsound, dusty or actively corroding surfaces without proper preparation. Dry and cure times depend on depth and conditions; confirm dryness before painting. Not intended for structural repairs. Pro Tips Feather edges wide for invisible paint blending on weathered timber and render. Keep a small cup of clean water nearby to maintain a smooth final pass. Deep cavities: bridge with successive thin layers for the most stable result.
$22.50 - $28.73
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$48.79
The Pink Stuff Miracle Cleaning Paste is a multi-purpose, mildly abrasive paste cleaner for lifting grease, grime and stubborn marks around the kitchen, bathroom, barbecue area and garden, supplied here in the 850g tub. It is a vegan, cruelty-free formula that is built to cut through baked-on residue while staying gentle enough for regular household cleaning when used with a light touch.About the formulaA thick, pink, rhubarb-scented paste that uses fine mineral particles as a mild abrasive, backed by a soap-based cleaning action. The manufacturer describes it as a 99% natural-ingredient, non-hazardous formulation. It is phosphate free, bleach free and not a concentrate, so there is nothing to dilute: you simply take a small amount on a cloth or sponge.Where to use itIndoors: saucepans and cookware, cooker tops and ovens, sinks, ceramic tiles, showers, glass and brass or copper fittings.Outdoors: barbecues, garden furniture, uPVC window frames and trims, painted surfaces and boat surfaces.Suitable for a wide range of hard surfaces including stainless steel and other metals, ceramic tiles, glass, sinks, uPVC and painted finishes. Take extra care on glass, highly polished steel and ceramic hobs, and always test first on a small, hidden area if you are unsure.How to use itScoop a small amount of paste onto a soft cloth or sponge and rub the surface gently. Rinse off thoroughly with hot water and wipe dry. Do not press hard, as too much pressure can scratch some surfaces. Do not let the paste dry on the surface. Press the lid back on firmly after each use.Important notesThis is a mild abrasive cleaner, so use it with care on delicate, soft or highly polished finishes. Do not use it on hot or warm surfaces. It is not an antibacterial product and does not contain bleach. Store the tub upright with the lid on.Specifications Brand The Pink Stuff Product Miracle Cleaning Paste Pack 850g tub Colour Pink Form Paste (ready to use, not a concentrate) Fragrance Rhubarb Cleaning action Mild abrasive plus soap-based cleaning Application By hand with a soft cloth or sponge Phosphate free Yes Bleach added No Vegan and cruelty-free Yes Use Indoor and outdoor SafetyUse with normal care: avoid contact with eyes, wear gloves if you have sensitive skin and wash your hands after use. Keep out of reach of children. Store upright in a cool, dry place out of direct sunlight and away from extreme temperatures, with the lid replaced after use. Refer to the Safety Data Sheet (SDS) for full details.
$8.10
FrogTape Pro Grade Deck and Joist Flashing Tape is a linerless, black waterproofing tape made to shield the timber parts of a deck from moisture, supplied here as a 96mm wide x 15.2m roll. It suits deck joists, stair stringers, posts and ledger boards, adding a protective layer over the surfaces most exposed to water, and it is a practical choice for both builders and capable DIYers.About the formulaThe tape pairs a solventless acrylic adhesive (ShurGRIP) with a conformable black polyolefin film backing. The adhesive is made using a UV curing process, is free of volatile organic compounds (VOCs) and is designed not to react with common caulks and sealants. The film bends easily around edges, corners and other transitions, and the tape self-heals around nails, screws and other fasteners to keep a waterproof seal. It is self-wound, so there is no release liner to peel and dispose of, and no primer is needed.Where to use itOutdoors: the tops and sides of deck joists, stair stringers, posts and ledger boards in residential deck construction, where the tape helps keep water away from framing timber.Installation temperature: it can be applied in a wide range, from -18°C to 65°C, and once installed it is designed to keep performing from -40°C to 115°C. It is rated for all-weather performance, including cold and damp conditions, and has 12-month UV resistance while exposed.Suitable surfaces include pressure-treated timber, OSB, concrete and other common building materials. The adhesive is initially repositionable, so you can adjust placement before pressing it down firmly.How to use itMake sure the surface is clean, dry and free of grease, oil and other contaminants. Unroll the tape along the joist, stringer, post or ledger, position it, then press it down firmly so the adhesive makes full contact. Work the tape around edges and corners, and press it into the surface around fasteners. Wider widths wrap further down the sides of a joist, so choose the width that best matches your framing. The same tape is also made in 48mm, 152mm and 304mm widths.Important notesThe manufacturer states the tape meets the AAMA 711-22 flashing tape test protocol. The 12-month UV resistance applies to the tape while it is exposed, so cover it with your decking or cladding in good time. As with any building product, check that it suits your surface and method of application before starting a larger job.Specifications Brand FrogTape Product Pro Grade Deck and Joist Flashing Tape (FSW 058) Size 96mm x 15.2m roll (1 roll) Colour Black Thickness 0.33mm Backing Black polyolefin film Adhesive Solventless acrylic Liner None (self-wound) Application temperature -18°C to 65°C Service temperature after install -40°C to 115°C UV resistance 12 months Standard AAMA 711-22 Use Exterior, above ground deck framing SafetyUse with normal care and keep the roll away from heat and open flame. Wear gloves when handling the tape on site to protect your hands from sharp edges and fasteners. Keep out of reach of children and store the roll in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$75.76
Selleys Liquid Nails VP30 Primer is a rapid-curing, water-based priming concentrate designed as a bridging primer in the Liquid Nails timber flooring system, supplied here in a 1L pack. It is used on concrete slabs and other porous or non-porous surfaces before levelling compounds or flooring adhesives go on, and it flashes off in about 30 minutes so the next stage of the job can start quickly.About the formulaA water-based hybrid polymer primer that is low in VOCs and low in odour. It changes colour as it dries, going on pink and turning red when dry, so you can see at a glance when a coat is ready. Once cured it will not re-emulsify in water, and tools and splatter can be cleaned up with water before the primer cures.Where to use itIndoors: as a bridging primer between Selleys VBS or VBS Rapid moisture barrier and self-levelling compound on concrete slabs, or to prime concrete before self-levelling compound is poured as part of a timber flooring installation.Outdoors: not intended for outdoor use. It is an interior product.Suitable for clean, sound concrete slabs and other porous or non-porous surfaces that will be topped with adhesives or floor skimming and levelling compounds. Check compatibility with your chosen flooring products before starting.How to use itStart with a clean, sound, dust-free surface and stir the primer well before use. Cut in the edges with a brush, then apply with a roller, brush or broom. Allow for roughly 6 to 10 m² per litre, depending on how porous the surface is. Leave a continuous film on the surface so the next layer bonds properly. Pour the primer out onto the floor rather than leaving it in the container, which keeps it cool and gives you more working time. Make sure the primer has dried clear and can be walked on without tackiness before pouring self-levelling compound. Good ventilation helps it cure faster. Clean up with water before the primer cures.Important notesCure time is about 30 minutes, depending on conditions. Very porous concrete or slabs with high moisture content may need a second coat. If the coating soaks away or you see dull patches or pinholes, apply another coat once the first has cured. If you are priming over a moisture barrier, make sure it is fully cured first. Do not apply over dusty or contaminated surfaces, and do not use on surfaces that are subject to standing water. Brushes and rollers are best discarded after use.Specifications Brand Selleys Product Liquid Nails VP30 Primer Size 1L Colour Pink when wet, red when dry Base Water-based Application Brush, roller or broom Cure time About 30 minutes Coverage About 6 to 10 m² per litre, depending on surface Clean up Water, before curing Use Interior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. If product gets on skin, wash with plenty of soap and water, and if it gets in eyes, rinse cautiously with water for several minutes. Keep out of reach of children and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$48.95
Selleys Liquid Nails Timberflex is a flexible, trowel-grade timber flooring adhesive for fixing solid, engineered strip and sheet timber floors to concrete and timber subfloors, supplied here as a single 600ml sausage pack. It is a good fit for smaller flooring jobs, patch work and trial areas where a full pail is more than you need.About the formulaTimberflex uses a silyl modified polymer (MS polymer) technology, which Selleys describes as isocyanate free and solvent free. It stays flexible once cured so the floor can move naturally. It forms clean, stable ridges under the trowel and gives good wet grab and initial hold. It spreads easily across a wide application range of 5°C to 40°C and is a low VOC product that meets Green Building Council requirements.Where to use itIndoors: engineered overlay flooring (prefinished and bamboo) and most types of solid timber, strip and sheet flooring, bonded to common subfloors such as plywood, particleboard, existing strip flooring, fibre cement sheet and concrete, including over acoustic matting.Outdoors: not recommended. This is an interior flooring adhesive and is not intended for wet areas.Suitable materials include plywood, particleboard, existing timber flooring, fibre cement sheet and steel-trowelled concrete.How to use itSurfaces must be clean, sound and level to within 3mm over 3m, because out-of-level floors increase the risk of hollow spots under strip timber. Grind concrete to remove high spots, contaminants and weak surface layers, and sand timber subfloors to remove old glue and other contaminants. Concrete should have a steel-trowel type finish. Over concrete, Selleys recommends a vapour barrier such as Liquid Nails VBS before laying to prevent moisture migration and swelling of the timber. Slab moisture content should be below 5.5% and moisture vapour transmission below 15g/m² per 24 hours. Apply the adhesive to the subfloor and spread it with a suitable Selleys Direct Stick trowel, then lay the boards into the wet adhesive. Wipe uncured adhesive from tools, hands and prefinished boards with a damp cloth before it cures.Important notesAlways follow Australian Standards, NCC requirements and best practice for timber floor installation. Allow about 24 hours for the adhesive to cure. The working time is about 45 minutes at 25°C and 50% relative humidity. Do not apply to dusty, greasy or damp surfaces. Cured adhesive is much harder to remove than wet adhesive, so clean up promptly.Specifications Brand Selleys Product Liquid Nails Timberflex Timber Flooring Adhesive Pack 1 x 600ml sausage Colour Oak Base Silyl modified polymer (MS polymer) Application Trowel applied Application temperature 5°C to 40°C Working time About 45 minutes (25°C, 50% RH) Cure time 24 hours VOC 32g/L Clean up Damp cloth before curing Use Interior timber flooring SafetyAvoid contact with eyes and prolonged or repeated skin contact, and wear gloves when working. Keep out of reach of children. Store in a cool, dry, well-ventilated place out of direct sunlight and away from foodstuffs. Refer to the Safety Data Sheet (SDS) for full details.
$19.06
Selleys Flexiseal Clear is a premium, crystal-clear multipurpose elastic joint sealant for DIYers and tradies who want a flexible, weather-tough seal that stays discreet. Supplied in a 290ml cartridge, it handles everyday sealing jobs indoors and out, and it can be applied to damp or wet surfaces without a primer.About the formulaBuilt on Selleys hybrid technology (a moisture-curing silyl-modified polymer), this sealant has a low modulus, non-slumping body that stays put in joints up to 20mm wide. It cures to a strong, elastic, waterproof seal that resists UV and weathering and keeps its clear finish. It is free from solvents and isocyanates, has a low odour, and meets Green Building Council of Australia low VOC limits for general purpose and architectural sealants. Once cured it can be painted with water-based paints.Where to use itIndoors: gaps and joints around windows, doors, skirtings, trims and fittings where a clear, flexible seal is wanted.Outdoors: vertical and horizontal joints in exterior cladding, around frames and between common building materials exposed to sun and rain.Suitable materials include concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles and glass, along with most other common building surfaces. Test first on painted surfaces and any unusual materials.How to use itClean the joint and remove dust, grease and other contaminants, and degrease metal surfaces. Cut the nozzle at an angle, slightly wider than the joint, and load the cartridge into a caulking gun. Use a suitable backing rod to control depth where needed. Gun the sealant into the joint and tool it off promptly so it makes good contact with both sides. Remove excess uncured sealant with a damp cloth. Paint with water-based paints once the surface has skinned or cured.Important notesNot suitable for polyethylene, polypropylene or Teflon (PTFE). Not intended for permanent water immersion. Application is best between 5°C and 35°C. Cure time depends on temperature, humidity and joint depth, so allow enough time before putting the joint under stress or exposing it to water.Specifications Brand Selleys Product Flexiseal Clear Multipurpose Sealant Pack 290ml cartridge Colour Clear Base Moisture-curing silyl-modified polymer (hybrid technology) Application Cartridge, via caulking gun Skin time About 45 minutes (23°C, 50% RH) Non-slump Joints up to 20mm wide Density Approx. 1.05 g/mL Application temperature 5°C to 35°C Service temperature -20°C to 70°C Paintable Yes, with water-based paints Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. Keep out of reach of children and store in a cool, dry place with the cartridge sealed. Refer to the Safety Data Sheet (SDS) for full details.
$23.03
Gyprock Pro-Repair 10 is a fast-setting, plaster-based jointing and patching compound, supplied here as an 8kg bag for small jointing jobs and everyday wall and ceiling repairs. It gives you roughly ten minutes of working time once mixed, so you can fill, tape and move on without waiting for a slow-drying compound to dry. It suits tradies, renovators and keen DIYers who want quick results.About the formulaPro-Repair 10 is a lightweight, low-VOC powder that you mix with water. It is a setting compound, so it hardens by chemical reaction rather than by evaporation. It is tinted so repairs are easy to spot on painted surfaces. It is designed to stick well to jointing tape, to shrink very little, and to sand easily as a topcoat. You can use it for every coat of a three-coat joint or as a base coat only. If you use it for all three coats with an open-weave fibreglass tape such as FibaFuse, you can sand the topcoat on the same day once it has dried enough. It is made in Australia by CSR Gyprock.Where to use itIndoors: patching holes, nicks, cracks and other defects in new and existing plasterboard walls and ceilings, and jointing smaller residential or commercial rooms.Fibre cement: suitable for repairs and jointing on Cemintel fibre cement sheet as well as Gyprock plasterboard.Suitable surfaces are Gyprock plasterboard and fibre cement. It is not recommended for wet areas.How to use itStart with a clean, dust-free surface. Tear the bag open at a top corner and mix with clean water as directed on the pack. Because the working time is short, mix only as much as you can use in one go. Apply by hand with a knife or similar tool. Embed the jointing tape in the base coat, then add further coats as needed. Let the compound dry fully, then sand the topcoat smooth before you prime and paint. Throw away any mixed compound you have not used. Keep unused powder in its original bag with the top rolled down, inside an airtight container.Important notesPro-Repair 10 is a setting compound, so you cannot rework it once it has started to set. Do not add water to extend the working time. It is not recommended for wet areas. Shelf life is one year from the date of manufacture, so store the bag somewhere dry and out of the weather and direct sun. Allow enough drying time before sanding, even when you are finishing the job on the same day.Specifications Brand Gyprock (CSR) Product Pro-Repair 10 Jointing and Patching Compound Pack 8kg bag Form Dry powder, mix with water (not pre-mixed) Base Lightweight plaster-based setting compound Application Hand applied Working time About 10 minutes after mixing Setting time About 30 minutes Coverage About 13kg per 100m² Suitable surfaces Plasterboard and fibre cement Shelf life 1 year from manufacture Standard Used in line with AS/NZS 2589 (Gypsum linings, application and finishing) Origin Australian made SafetyDust can irritate the eyes and may aggravate existing eye conditions, so avoid breathing dust and avoid eye contact and prolonged skin contact. Wear gloves, eye protection and a dust mask when mixing and sanding. In case of eye contact, flush thoroughly with running water for 15 minutes with the eyelids held open. Store in a cool, dry, well-ventilated place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$50.21
Davco Ultraflex is a premium grade, cement-based tile adhesive for walls and floors, supplied here as a 20kg bag for full tiling jobs. It is rubber modified, so it suits both rigid and flexible substrates, and it is rated for commercial work as well as home renovations.About the formulaA powder adhesive that you mix with clean water and apply with a notched trowel. The rubber modification gives it extra flexibility over framed and sheet substrates. It is suitable for use over early age screed (cured for 24 hours) and over under-tile heating. It is classified C1S1E under AS ISO 13007 and has a low VOC content of 5 g/L (SCAQMD method 304-91).Where to use itIndoors: living and dining areas, walkways and office spaces, on both walls and floors.Outdoors: external verandahs and decks, on both walls and floors.Suitable tiles include porcelain, ceramic, mosaic, terracotta, slate, quarry, granite and marble. Suitable substrates include cement render, blockwork and rendered brickwork, plasterboard, fibre cement sheet, compatible waterproofing membranes, timber floors (with fibre cement tile underlay installed), new concrete (cured for 7 days) and new screed (cured for 24 hours). The adhesive is not suitable for translucent tiles or for moisture sensitive stone such as green marble.How to use itMake sure the substrate is sound, firmly fixed, clean and free of dust, oil and loose material. Prime the surface where the data sheet calls for it (for example plasterboard, fibre cement sheet, screed and timber floors with tile underlay), using the Davco primer the manufacturer recommends for that substrate. Mix the powder with clean potable water to a smooth, lump-free consistency, about 7 litres of water per 20kg bag. Spread the adhesive with a notched trowel suited to your tile size and press the tiles firmly into place. A 20kg bag covers about 12m2 when applied with a 6mm notch trowel, and less with larger trowels. Clean tools with water while the adhesive is still fresh, and wipe wet adhesive off tile faces with a damp cloth. Cured adhesive is much harder to remove.Important notesAllow 6 to 8 hours before grouting. Check the manufacturer's data sheet for substrate preparation, primers and movement joint requirements before you start. Store unopened bags off the ground in cool, dry conditions. Shelf life is up to 12 months when stored this way. If you plan to use it on a surface or in an application not covered by the data sheet, contact the manufacturer first.Specifications Brand Davco Product Ultraflex Premium Grade Cement-Based Tile Adhesive Pack 20kg bag Base Cement-based, rubber modified powder Application Mixed with water, applied by notched trowel Coverage About 12m2 per 20kg bag (6mm notch trowel) Time before grouting 6 to 8 hours Classification C1S1E (AS ISO 13007) VOC content 5 g/L (low VOC) Use Interior and exterior, walls and floors, commercial and domestic SafetyThis product contains cement, which is alkaline and can cause dermatitis. Wear PVC or similar gloves and safety goggles when mixing and applying. Avoid breathing in the dust when opening bags and mixing, and use suitable dust protection where needed. Wash skin with water after contact. Refer to the Safety Data Sheet (SDS) for full details.
$40.69
![Sika SikaBond T-55(J) Elastic Wood Flooring Adhesive 600ml Foil Pack [Ochre] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikabond-t-55-j-elastic-wood-flooring-adhesive-600ml-foil-pack-ochre-2.jpg?v=1792411222&width=645)
Sika SikaBond T-55(J) is a one-component, elastic polyurethane adhesive for fully bonding solid and engineered timber floors, supplied here as a single 600ml foil pack for smaller flooring jobs and repairs. It spreads easily, stays flexible once cured and helps take the stress out of the bond between the timber and the substrate, which suits floors that need to move a little with the seasons.About the formulaA moisture-curing polyurethane that cures by reacting with humidity in the air, so it needs reasonable ambient moisture to set properly. The cured adhesive is elastic and dampens footfall sound. It is sandable along with the floor, and Sika rates it as low in VOCs. It is approved for use over underfloor heating and can be applied directly onto old ceramic tiles, which can save you from ripping up an existing tiled floor first (do a preliminary adhesion test on glazed tiles).Where to use itIndoors: full-surface bonding of solid timber and engineered timber floors, parquetry and strip panels, mosaic and industrial parquet, and chipboard, over concrete, cement-based screeds, timber subfloors and old ceramic tiles. It can also be used as an underlay layer before timber flooring is laid.Outdoors: not intended for outdoor use, and it is not rated as UV or weather resistant.Suitable substrates include concrete, cement-based floors, chipboard, timber subfloors and ceramic tiles. Sika notes that ground-floor slabs and areas without a damp-proof membrane need moisture protection first (see important notes below).How to use itMake sure the substrate is clean, dry, sound and free of dust, contamination and old coatings or adhesives. Check the substrate moisture content before you start and prime or seal where required. Load the foil pack into a suitable application gun, snip the end and cut the nozzle tip to suit, then lay the adhesive over the floor and spread it evenly with a notched trowel. Sika's current data sheet lists coverage of roughly 600 to 1000 g per square metre depending on the trowel notch and the flooring type. Use a larger notch for long or wide boards and uneven substrates so you get a continuous bed with no hollow spots. Press the timber firmly into the adhesive while it is still wet and keep a 10 to 15mm expansion gap to the walls. Clean tools while the adhesive is uncured, using Sika Remover-208 or Sika Colma Cleaner. Cured adhesive can only be removed mechanically.Important notesSika's data sheet states this product is only suitable for use by professional wood floor applicators. Apply and lay within roughly 15 to 35 degrees ambient and substrate temperature (20 to 35 degrees with underfloor heating), with relative humidity of about 40 to 70 percent. Keep the adhesive at or above 15 degrees for good workability. The floor can be walked on after about 12 hours and sanded after about 24 hours, depending on conditions and adhesive thickness. Do not expose uncured adhesive to alcohol-containing products, as they interfere with curing. Where a ground-floor slab or other area has no damp-proof membrane, follow Sika's moisture-barrier recommendations (Sika Primer MB or MR Fast, or Sikafloor EpoCem) before laying timber. Follow the flooring manufacturer's own installation guidelines as well.Specifications Brand Sika Product SikaBond T-55(J) Elastic Wood Flooring Adhesive Pack 1 x 600ml foil pack Colour Ochre Base 1-component polyurethane, moisture curing Application Foil pack via application gun, spread with a notched trowel Skin / laying time About 60 minutes at 23 degrees and 50% RH Cure rate About 3mm per 24 hours at 23 degrees and 50% RH Walk on / sand After about 12 hours / 24 hours Coverage About 600 to 1000 g per m2, depending on trowel and flooring type Density About 1.35 kg/l Shore A hardness About 38 after 28 days Shelf life 12 months from production, unopened and stored correctly Storage Dry, out of direct sunlight, 5 to 25 degrees Use Interior only SafetyIt contains small amounts (under 1 percent) of isocyanates, so avoid skin contact and breathing vapour, and keep the product away from heat, sparks and open flames. Work in a well-ventilated area and wear gloves and eye protection. If it gets on skin, remove contaminated clothing and wash with soap and plenty of water. For eye contact, rinse with water with the eyes held open and seek advice if irritation persists. Refer to the Safety Data Sheet (SDS) for full details.
$19.37
Betta Tilecare Stone & Concrete Sealer from Bondall is a water-based, clear sealer that soaks into stone and concrete and also builds a protective film on top, supplied here in a 1L pail. It is designed to bind and protect the surface, repel moisture and help guard against stains and soiling, while keeping the natural look of the material.About the formulaA water-based, low odour, low VOC sealer with a combined penetrating and film-forming action. It dries to a clear natural finish, so it enhances the surface rather than hiding it. The film helps resist staining and soiling and reduces salt and hard water build-up. It can be used on both horizontal and vertical masonry surfaces, and recoating can follow straight away.Where to use itIndoors: interior flooring, kitchen, laundry and bathroom areas with stone, concrete, ceramic or porcelain surfaces.Outdoors: access areas and walkways, alfresco areas and balconies.Suitable materials include stone, slate, granite, concrete, ceramic and porcelain. Always test a small, inconspicuous area first to check the result on your particular surface.How to use itStart with a clean, dry surface that is free of dirt, grease, oil and other contaminants, and fix any stains or mould growth before sealing. Apply evenly to the surface and avoid pooling or over-application. Because the sealer can be recoated immediately, you can complete additional coats in the same session. Follow the directions on the pack for the number of coats, application tools and clean-up.Important notesAllow about 24 hours to dry before use. Drying and cure times vary with temperature, humidity and how porous the surface is. Sealed surfaces can behave differently under foot, so check grip on smooth or dense surfaces before putting a sealed floor into service. Sold for residential use. Check the pack directions for any surfaces the manufacturer lists as unsuitable.Specifications Brand Bondall Product Betta Tilecare Stone & Concrete Sealer Size 1L pail Finish Clear natural Base Water-based Action Penetrating and film forming Dry time 24 hours Recoat Immediate Suitable surfaces Stone, slate, granite, concrete, ceramic, porcelain Use Interior and exterior, residential SafetyIt is water-based with low odour and low VOCs, but it should still be handled with care. Keep it out of reach of children, use it in a well-ventilated area, and avoid contact with skin and eyes. If it gets on skin or in eyes, rinse well with plenty of water. Refer to the Safety Data Sheet (SDS) for full details.
$29.03
Crommelin DiamondTough Stone Shield Clear Sealer is a premium waterborne sealer made for dense natural stone, supplied here in a 1L pack that suits benchtops, feature walls and smaller floor areas. It protects against stains and water, dries clear, and leaves a natural to low sheen finish. Crommelin previously sold it as DiamondCoat Stone Shield. The brand says only the name has changed, not the product.About the formulaA water-based sealer that both penetrates the surface and forms a thin protective film, while still letting the stone breathe. It resists staining and abrasion and repels water well. It also contains an anti-microbial additive that helps stop mould and algae growing on the sealed surface. It is low odour and low VOC, dries quickly, and can be recoated soon after the first coat. It can be applied to vertical and horizontal surfaces.Where to use itIndoors: dense stone floor and wall tiles, stone and concrete benchtops, kitchens and living areas, and polished concrete.Outdoors: natural stone cladding and other exterior dense stone surfaces that suit a clear, low sheen protective coat.Suitable surfaces include granite, marble, bluestone, travertine, porcelain, polished concrete, terracotta, reconstituted stone and natural quarry stone. Always test a small patch first to check the colour enhancement, finish and slip resistance.How to use itThe surface must be clean and fully dry before you start. Crommelin requires a moisture test every time. If the surface has been acid etched, neutralise and rinse it thoroughly first. Apply the first coat evenly with a clean, lint-free tool so the surface is wet but no white excess liquid is left standing. Suitable tools are a brush, a roller, a lambswool applicator, a lint-free cloth or an airless sprayer. Apply the second coat in the same way once the first is touch dry, and within 2 hours. On very dense surfaces such as polished marble, the sealer may only need to be wiped on. If streaky film builds up on a dense surface once dry, wash it with warm soapy water, rinse and buff with a soft cloth. Clean tools with warm water and a little detergent straight after use.Important notesDo not apply when it is too hot or cold, when humidity is high, or when rain is expected within 48 hours. Allow about 24 hours before light foot traffic. Full cure takes around 7 days. Over-applying can leave a visible film on very dense stone, so work thinly and use a test patch to confirm the right rate. This product is a clear sealer. It cannot be tinted.Specifications Brand Crommelin Product DiamondTough Stone Shield Clear Sealer Pack 1L pail Colour Clear when dry Base Waterborne Finish Natural to low sheen Application Brush, roller, lambswool applicator, lint-free cloth or airless spray Recoat As soon as the first coat is touch dry, within 2 hours Light foot traffic About 24 hours Full cure About 7 days Application temperature 5 to 35°C Coverage Roughly 10 to 30 m² per litre, depending on how dense the surface is Primer required No Tintable No Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, avoid breathing spray mist, and wear suitable protective clothing, gloves and eye protection when spraying. Keep the container sealed and store it in a cool, dry place. Keep it out of reach of children, and do not let it enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$49.55
The Gyprock Rapid Repair Kit is a complete, ready-to-go pack for patching damaged plasterboard walls and ceilings, from small nicks and cracks through to holes up to 150mm x 150mm. Everything needed for the job is supplied in one mixing bucket, so a first-time DIYer can go from damaged wall to a surface ready for paint without hunting down separate products or tools.About the formulaThe compound in the kit is Gyprock Rapid Patch, a fast-setting dry powder that you mix with clean water into a smooth paste. Gyprock lists a working life of around 20 minutes once mixed, with minimal shrinkage when filling small cracks and dents, and a surface that is ready to sand in around 40 minutes. Gyprock lists the powder at a specific gravity of 2.3 to 2.4 and a low VOC content, under 10 g/L per material. The kit is made in Australia by CSR Gyprock.What is in the kit 1kg bag of Gyprock Rapid Patch compound 2 x Gyprock plasterboard repair panels (150mm x 150mm) for larger holes Gyprock Easy Tape (20 metres) 100mm broadknife Sanding block Mixing bucket (also the kit's packaging) Step-by-step instructions Where to use itIndoors: patching dents, scratches, cracks and holes in plasterboard walls and ceilings, including door-handle dings and holes left by removed fixings or fittings.Other substrates: the Rapid Patch compound itself is also rated by Gyprock for repairs to fibre cement, timber and masonry, and it can be used as an all-purpose compound for setting plasterboard joints. Check the substrate and the finish before using it in damp areas.Suitable materials include plasterboard (the main use of the kit), fibre cement, timber and masonry (the compound only).How to use itRemove any loose paint or crumbling material around the damage and lightly sand the edges. Mix the powder with clean water to a creamy consistency. Gyprock's guide for small repairs is about 1 cup (260g) of powder to 150mL of water. Only mix as much as you can use in around 20 minutes. For small nicks and cracks, fill with the broadknife, let it set, then sand smooth. For larger holes, cut and fit a repair panel with backing blocks fixed using the compound, cover the joins with Easy Tape, and apply compound over the tape. Let each coat set fully before the next, then sand lightly and the wall is ready to paint.Important notesUse clean domestic water for mixing, and wash tools before the compound sets. The kit is aimed at repairs up to 150mm x 150mm, so larger damage will need a bigger repair. You may also need a hand saw, trimming knife, pencil, dust mask and eye protection depending on the job. Store unused compound dry, out of the weather and out of direct sunlight.Specifications Brand Gyprock (CSR) Product Rapid Repair Kit Pack Single kit, 1.5kg nominal (1kg Rapid Patch compound plus panels, tape and tools) Base Plaster-based dry powder, mixed with water Application Hand applied with the supplied broadknife Working time (Rapid Patch) About 20 minutes Ready to sand (Rapid Patch) About 40 minutes Repair size Up to 150mm x 150mm Specific gravity 2.3 to 2.4 VOC content Under 10 g/L per material Suitable surface Plasterboard walls and ceilings Origin Made in Australia SafetyCutting, sanding or grinding the set material makes dust that can irritate the eyes, nose and throat, so wear a dust mask and eye protection and avoid prolonged skin contact. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$49.75
Gyprock Masonry Adhesive is a dry powder adhesive made for fixing plasterboard directly to masonry and concrete walls, supplied here in a 20kg bag for full-room and trade-sized jobs. You mix it with water on site to a firm, creamy paste. It is also used to fix plaster cornice and decorative plaster castings to plasterboard walls and ceilings in residential and commercial buildings.About the formulaThis is a plaster-based, setting-type compound rather than a drying type. Once mixed, it has a working life of about 40 to 45 minutes before it starts to set. The manufacturer designs it for strong adhesion and good initial grab, and it is easy to spread by hand with a small broadknife. It is made in Australia by CSR Gyprock. The manufacturer lists a very low VOC content of 2g/L (as specified by GBCA) and notes the product is GECA accredited.Where to use itIndoors: direct-fixing plasterboard sheets to brick, block and concrete internal walls, and fixing plaster cornice and plaster castings to plasterboard walls and ceilings.Outdoors: not intended for external use. It is an internal wall lining adhesive.Suitable surfaces include brick, concrete and other masonry, plus plasterboard for cornice and casting work. Remove any paint from the areas where the adhesive will be applied.How to use itPour the powder slowly into clean domestic water and mix to a firm, creamy consistency. The manufacturer's guide is roughly 3kg of powder to 1.5 litres of water. Mix only what you can use within the working life, and never mix or re-work adhesive once it has begun to set or dry. For plasterboard, apply daubs of about 50mm diameter that stand out at least 15mm from the wall. Keep daubs no more than 450mm apart horizontally and vertically, and keep them about 50mm in from sheet ends and edges. You can apply daubs to either the wall or the back of the sheet. Position the board and hold it in place until the adhesive sets. Use levelling pads where wall irregularities exceed 15mm. Always follow the current Gyprock installation guides for full fixing details.Important notesNot suitable for use on wet area plasterboard in tiled areas. Use only clean domestic water for mixing. Keep fresh batches free from contamination and do not mix with set or drying material. The bag is non re-sealable, so plan the quantity you need. Shelf life is 12 months from the date of manufacture when the bags are stored dry, out of the weather and away from direct sunlight. Wall suitability, fixing limits and any decoration requirements should be checked against the Gyprock Red Book and technical data sheet for your job.Specifications Brand Gyprock (CSR) Product Masonry Adhesive Pack 1 x 20kg non re-sealable bag Form Dry powder (mix with water) Colour Off white Base Plaster-based setting compound Application By hand with a broadknife, applied as daubs Working life once mixed 40 to 45 minutes Coverage 20kg fixes approximately 30m2 of plasterboard Specific gravity 2.3 to 2.4 VOC content (GBCA) 2g/L Shelf life 12 months from manufacture Origin Made in Australia Use Interior SafetyAvoid eye contact and repeated or prolonged skin contact, and avoid breathing in the powder dust when opening, pouring and mixing. Wear gloves and eye protection, and use a dust mask or respirator in dusty conditions, especially when sanding or cutting set material. Wash well after handling. Store bags in a dry place, protected from weather and direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$71.12
Gyprock DIY Cornice Cement is a powder-based, mix-with-water adhesive made for fixing cornice at the wall and ceiling junction, supplied here in a handy 2.5kg bag for small rooms, repairs and touch-ups. It is a setting-type compound rather than a drying type, so it grabs well at the start and builds a high bond strength once set. It is made in Australia by CSR Gyprock.About the formulaA dry plaster-based powder that you mix with clean water into a workable paste. Once mixed, you get a working life of roughly 50 to 60 minutes, which is enough to fix several lengths of cornice and tidy the joints without rushing. Because it sets by reaction rather than by drying out, it hardens in a predictable timeframe. Gyprock describes it as a low VOC product.Where to use itIndoors: fixing Gyprock cornice at wall and ceiling junctions where the lining is plasterboard or fibre cement, finishing cornice joints and mitres, filling small gaps along the cornice line and carrying out small cornice repairs.Outdoors: not intended for exterior use. It is designed for interior cornice work.Suitable surfaces are plasterboard and fibre cement wall and ceiling linings, bonded to Gyprock cornice.How to use itCut cornice sections to length using a saw and mitre box or a mitre guide. Add 2kg of powder to 1.1 litres of clean water and mix to a creamy consistency. Only mix as much as you can use within the 50 to 60 minute working life. Apply the cement with a broadknife as a bead along both back edges of the cornice and onto the mitres. Butter and fix each length separately, starting with the shorter lengths. Hold each piece in place with temporary nails or screws, then remove the surplus cement and clean off with a brush or sponge. Smooth the mitres and fill any gaps with more cement. Leave it to set for at least 2 hours before removing the temporary fixings and sanding the joints.Important notesThe bag is not re-sealable, so plan your batches and keep the bag closed and dry between uses. Shelf life is 12 months from the date of manufacture. Do not mix more than you can use in the working time, and do not re-use material that has started to stiffen. Gyprock lists this product for residential cornice fixing and repairs on plasterboard and fibre cement. Clean tools with water before the cement sets.Specifications Brand Gyprock (CSR Gyprock) Product DIY Cornice Cement 60 Pack 2.5kg bag Colour Off white Base Plaster-based powder, setting type Application Mixed with water, applied with a broadknife Mix ratio 2kg powder to 1.1 litres of water Working time 50 to 60 minutes after mixing Set before sanding At least 2 hours Specific gravity 2.3 to 2.4 VOC content 2g/L Shelf life 12 months from manufacture Origin Made in Australia Use Interior SafetyDust created when sanding or cutting the set material is a nuisance dust, so keep dust low, work in a ventilated space and wear gloves, eye protection and a suitable dust mask when sanding. If it gets in your eyes, flush with plenty of running water, holding the eyelids open, for about 15 minutes. Store the bag in a dry place and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Artko Artists Epoxy Resin is a two-part, 1:1 mix casting and coating resin for resin art, supplied here as a 1 litre kit with a starter set of accessories. It cures to a crystal clear, glass-like finish and is aimed at hobbyists and artists who want a simple mix ratio and a smooth, self-levelling result.About the formulaA two-part epoxy system made up of 500ml of resin (Part A) and 500ml of hardener (Part B), mixed in equal parts by volume. It is described as odourless, free of VOCs and BPA, and it contains a UV stabiliser to help resist yellowing over time. It self-levels to a flat, glossy surface and is heat resistant up to 80°C. The kit also includes a silicone mat (40cm x 30cm), a square silicone mould, gloves and pipettes, so you can start pouring straight away.Where to use itIndoors: resin art and pour paintings, coasters, trays, jewellery, keepsakes and small decorative pieces cast in silicone moulds.Coating and embedding: sealing and preserving items such as photographs, paper, shells and dried flowers under a clear glossy layer.Suitable materials include wood, metal, glass, silicone moulds, paper, photographs, shells and dried flowers. Always test on an offcut or a small area first, particularly on porous or unusual surfaces.How to use itWork in a well-ventilated area on a level surface, and protect your bench with the silicone mat. Measure equal parts of resin and hardener into a clean disposable cup or silicone mixing cup. Stir slowly for about 5 minutes until the mix runs clear, scraping the sides and base of the cup. If you want colour or sparkle, add mica powder or glitter a little at a time at this stage. Pour into a mould or onto a flat surface and leave undisturbed to cure. Warming the sealed bottles in warm water for about 30 minutes before mixing can help reduce bubbles. A heat gun or a toothpick can be used to pop any bubbles that rise to the surface.Important notesThe supplier gives a cure time at 25°C of about 3 to 4 hours to touch dry and about 12 to 24 hours to fully cure. Cooler rooms will slow this down. Accurate 1:1 measuring is essential, as an incorrect ratio can leave the resin soft or tacky. Keep dust, moisture and pets away while it cures. Multiple thin layers are better than one very deep pour. Cured resin is not intended for contact with food unless the manufacturer states otherwise. Clean tools before the resin cures, as cured epoxy is very hard to remove.Specifications Brand Artko Product Artists Epoxy Resin 1 Litre Kit Pack 1 litre kit (500ml resin + 500ml hardener) Colour Crystal clear Base Two-part epoxy resin Mix ratio 1:1 by volume Application Mix and pour, in moulds or as a flat coating Touch dry About 3 to 4 hours at 25°C Full cure About 12 to 24 hours at 25°C Heat resistance Up to 80°C Kit extras Silicone mat (40cm x 30cm), square silicone mould, gloves, pipettes Use Indoor craft and art projects SafetyEpoxy resins and hardeners can irritate skin and eyes and may cause an allergic skin reaction in some people with repeated contact. Wear the supplied gloves, protect your eyes, and work in a well-ventilated space. Avoid skin contact, and wash any splashes off straight away with soap and water. Keep out of reach of children and store the sealed bottles in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$64.13
![Roberts Quick-Repair Floor Putty 88ml [Black] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-black-2.png?v=1792410973&width=645)
Roberts Quick-Repair Floor Putty in Black is a ready-to-use acrylic filler for hiding gaps, nicks, scratches and fastener holes in laminate, vinyl, hybrid and engineered timber floors, supplied in a handy 88ml squeeze tube. It suits quick touch-ups on an existing floor as well as tidying up during installation, and it can be used straight from the tube or blended with other shades in the Roberts range to get a closer match to your flooring.About the formulaAn acrylic-based putty that is ready to use with no mixing. Roberts describes it as fast drying and non-shrinking, so the fill stays level with the surface. Once dry it can be sanded or painted over. The manufacturer lists it as low VOC, and each tube has a two-year shelf life.Where to use itIndoors: filling nail and screw holes made during floor installation, closing small gaps between boards or planks, and covering chips, dents and scratches on floors that are already down.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, vinyl, hybrid flooring, engineered timber and timber flooring. Black is a good base shade for dark floors, and it can be blended with other Roberts putty colours for in-between tones.How to use itClean the damaged area so it is free of dust and loose debris. Knead the tube thoroughly for at least 20 seconds before use. Squeeze putty into the gap, hole or scratch and press it in firmly so it fills the void, then smooth it level with the surrounding floor. Wipe away excess with a damp rag straight away and do not let putty dry on the surrounding flooring. If you need a custom shade, mix small amounts of different colours before applying, and test the match in an inconspicuous spot first. Once dry, the repair can be lightly sanded or painted if needed.Important notesColour can look slightly different once dry, so test first. Reseal the tube tightly after use, because putty left exposed to air can dry out in the tube. Heavily trafficked spots such as doorways may need a further touch-up over time. This is a cosmetic filler, not a structural repair product or an adhesive.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range), model PC7743 Pack 1 x 88ml squeeze tube Colour Black Base Acrylic Application Squeeze tube, applied by hand Dry time Around 30 minutes (distributor data, varies with depth and conditions) Finish Matte Shelf life 2 years Use Interior flooring repairs SafetyKeep out of reach of children, avoid contact with eyes and prolonged skin contact, and wash hands after use. Store the tube sealed in a cool, dry place away from frost. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Natural] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-natural-2.png?v=1792410959&width=645)
Roberts Quick-Repair Floor Putty in Natural is a ready-to-use acrylic repair putty for patching gaps, nicks and scratches in laminate, hybrid, vinyl and engineered timber floors, supplied in an 88ml squeeze tube. It works for both fresh installations and repairs to existing floors, and it can be mixed with other Roberts shades when you need a closer colour match.About the formulaAn acrylic-based putty that comes ready to use straight from the tube. The manufacturer describes it as fast drying, non-shrinking and easy to sand or paint once dry. It is low VOC and has a two-year shelf life. Natural is a light beige base shade that suits many flooring tones. It can be used on its own or blended with other shades in the range.Where to use itIndoors: fill nail and screw holes left during floor installation, close small gaps at plank edges, and touch up nicks, chips and scratches on existing floors.Suitable floors include laminate, hybrid, vinyl (including luxury vinyl plank and tile) and engineered timber.How to use itStart with a clean surface, free of dust and debris. Pick the shade that best matches the repair. The manufacturer advises matching to the lightest base colour of the floor, and you can mix shades to fine-tune it. Knead the tube thoroughly for at least 20 seconds, cut the tip to suit the bead size you need, and squeeze the putty into the damaged area. Work it into the gap, nick or scratch with a putty knife. Wipe off the excess straight away with a damp rag and do not let it dry on the surrounding floor. Once dry it can be lightly sanded or painted if needed.Important notesPutty can dry to a slightly different shade from how it looks in the tube, so test a small, discreet spot first. Reseal the tube after use, because putty left exposed can dry out. Mix and match shades before applying, not after. Check the manufacturer instructions if you plan to coat the repair with a clear finish.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range) Model PC7741 Size 88ml tube Colour Natural (beige) Base Acrylic Application Squeeze tube, spread with a putty knife Finish after cure Matte Shelf life 2 years Use Indoor flooring repairs and installation SafetyIt is a low VOC, water-based acrylic putty. As with any building product, keep it out of reach of children, avoid contact with eyes, and wash your hands after use. Store the tube sealed in a cool place. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
You have seen 48 out of 87 products
Adhesives and sealants engineered for reduced volatile organic compounds to support better indoor air quality. Verify any stated compliance or testing where relevant. Use filters to refine by chemistry and cure profile. Always check the product page and TDS/SDS for safety and ventilation notes.
