SikaSeal® Kitchen and Bathroom SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Uses Glass and enamel Ceramics and tiles Aluminium, steel, zinc, copper Plastic laminates Rubber Stainless steel Concrete and grouts Characteristics / Advantages Excellent adhesion Great weatherability Non-sag Great tooling characteristics Long-term mould resistance Interior and exterior usage Fast curing Colours White Beige Black Charcoal Transparent Alabaster Almond Ivory Off White Stone Pewter Grey Mid Grey Stone Brown Packaging 300ml cartridges, 12 cartridges per box Shelf Life 12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base: Neutral curing Density: 0.98 g/cm³ @ 23ºC Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h. Curing Rate: 72 hours @ 23ºC/50% r.h. Consistency: Non-sag Mechanical/Physical Properties Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h. Shore A Hardness: 20 SHA E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h. Ultimate Elongation: 300% Anti-mildew Property: 0 level
$14.00 - $17.33
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/add6c9293f9448a0b56570405080097d.jpg?v=1757756088&width=645)
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. SafetyTips Uncured product may irritate eyes. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Refer to the Safety Data Sheet (SDS) for full details.Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$16.00 - $20.16
Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.
$20.15 - $20.18$0.03/g
Dunlop Flexible Coloured Grout is a smooth-finish, flexible cement-based grout available in a wide palette of popular colours to complement almost any tile. Its stronger colour formula gives rich, consistent joints, while built-in Grout Shield anti-mould and anti-bacteria technology resists mould and bacteria growth to keep wet areas looking fresher for longer. Easy to work and forgiving to clean off, it ensures flush joints with no pin holes.Where to use itUse it on walls and floors, indoors and outdoors, with ceramic, porcelain, marble, granite and mosaic tiles. It handles joints from 1mm right up to 8mm, so one product covers both fine wall joints and wider floor joints. For swimming pools, use the White 200 colour mixed with Dunlop Primer & Additive.How to useMake sure joints are clean, dry and raked clear of adhesive. Mix the powder with clean water (or with Dunlop Primer & Additive for extra flexibility, adhesion and stain resistance) to a smooth paste. Spread diagonally across the tiles with a rubber float, packing joints full, then sponge the surface clean once firm and buff off the haze. Initial set occurs after about 24 hours; showers can be exposed to water after 3 days, the grout can be sealed after 3 days and full cure is reached in 7 days.Important notesCoverage depends on tile size, joint width and depth - allow around 15% wastage. Colour can vary slightly with water content and curing conditions, so mix consistently between batches.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing mixing dust, and wash after use. Keep out of reach of children; refer to the Safety Data Sheet.
$13.88 - $15.24
Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.
$70.50
Selleys Wet Area Silicone is a high-quality, neutral cure silicone sealant designed specifically for areas exposed to moisture, such as kitchens, bathrooms, and laundries. This 100% silicone formula provides a long-lasting waterproof seal that won’t shrink, crack, or peel for up to 25 years, making it ideal for sealing around showers, sinks, bathtubs, and other wet areas. Its anti-mould properties ensure that your bathroom stays hygienic and clean for longer. The 90ml tube is perfect for smaller jobs or touch-ups, offering easy handling for precise application in tight spaces. Selleys Wet Area Silicone adheres to a wide range of materials, including ceramics, glass, stainless steel, metal fittings, and plastic laminates, ensuring a secure, flexible seal in high-humidity environments. Whether you’re sealing around a kitchen sink or maintaining the edges of a shower enclosure, this product guarantees professional results every time. Where can this product be used? Showers screens Baths Spas Sinks Plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Clean surface with mineral turpentine and dry. Cut cartridge, fit and cut nozzle at 45° angle and fit into a caulking gun. Apply with steady pressure, ensuring sealant is pushed into joint. Tool with a spatula dipped in detergent water within 5-10 mins of application. Clean up with mineral turpentine before product skins. Sealant will cure in 72hrs. Limitations: Not paintable. Complete painting 7 days prior to applying sealant. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. Not suitable for aquariums. Not suitable for food or drinking water contact. Not suitable for permanent water immersion. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. *Warranty Information Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$13.62
Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.
$21.37
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-wet-area-bathroom-kitchen-sealant-90ml-clear-2.jpg?v=1792406361&width=645)
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout) The product also contains fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour so can be used in any environment without discomfort. Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam. Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. Temperature resistance – approximately -60°C +150°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Where can this product be used? Showers and sinks. Metal, copper and brass fittings. Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper and brass fitiings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal. Handy tips Tips for Using a Silicone Sealant in a Wet Area Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safetytips Uncured product may irritate eyes. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$13.62
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-sealant-waterproof-white-2.png?v=1792406184&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$23.83
Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters. Highly flexible Mould and UV resistant Neutral cure Non-corrosive
$10.20
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
Selleys White For Life Ready To Use Grout is a premium-quality, pre-mixed grout designed to deliver a brilliant, long-lasting white finish for wall and floor tiles. Suitable for interior applications with joints up to 5mm, this product is ideal for both new tile installations and regrouting jobs. Surface Preparation: Ensure all surfaces are clean, dry, and free from dust, oil, old grout, and other contaminants. For new tiling jobs, let tile adhesive set for at least 24 hours. For regrouting, completely remove old grout and thoroughly clean the joints. Application Instructions: Cut the cartridge tip and attach the nozzle. Trim to desired bead width. Using a caulking gun, apply grout into joints, pressing it in to eliminate air gaps. Smooth grout using a rubber float or grout applicator, working diagonally. After 15–20 minutes (depending on temperature), gently wipe tile surfaces with a damp sponge to remove excess grout and haze. Avoid over-wetting and excessive wiping, which can weaken the grout lines. After 24 hours, polish tile surfaces with a soft dry cloth to remove any remaining haze. Coverage: Approx. 2m² per 410g cartridge (based on 300x300mm tiles with 3mm x 5mm joints) Drying Time: Touch dry in 30 minutes Allow 72 hours before exposing to water in wet areas such as showers Clean-Up: Clean tools and tile surfaces with water before the grout cures Once dry, remove excess grout by mechanical means Technical Data: Colour: White Appearance: Smooth, creamy paste Joint Width: Up to 5mm Water Clean-Up: Yes (before curing) Shelf Life: 12 months if stored unopened in a cool, dry place
$19.72
![Selleys No More Gaps Exterior & Weatherboard 430g [White]](http://gluesaustralia.com.au/cdn/shop/files/8a8dbfbe2151431e9a3365cd49a9be75.jpg?v=1757753104&width=645)
![Selleys No More Gaps Exterior & Weatherboard 430g [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-more-gaps-exterior-weatherboard-430g-white-2.jpg?v=1792406093&width=645)
Selleys No More Gaps Exterior & Weatherboard is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. Has good resistance to weathering Contains a titanium compound for superior UV resistance. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application).. Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack. Is formulated for long term resistance to cracking and crumbling. Is water based, so can be cleaned up with water. Will not stain building materials. Where can this product be used? Between exterior window and door frames Fascia boards and eaves Masonry Walls Tiling Timber & synthetic weatherboards Brickwork Fences Where shrinkage or movement has caused rigid fillers to crack Gaps with a maximum width of 25mm & depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Fibre cement sheeting, plasterboard Masonry Ceramic Tiles Glass Aluminium & other metals Many other building surfaces
$17.87
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.80
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.26
Dunlop Easy Clean Epoxy Grout is a high-performance, durable epoxy grout with superior stain resistance that stands up to most household chemicals. Unlike traditional epoxies it is genuinely easy to use and clean during application, and just as easy to maintain afterwards. It also contains Grout Shield, a powerful mould inhibitor that resists the growth of mould and bacteria, keeping joints looking better for longer.Where to use itIdeal for areas subject to high wear and for spaces where strict hygiene matters - kitchens, bathrooms, laundries and swimming pools. Use it indoors and outdoors on walls and floors with ceramic, porcelain, vitrified tiles, mosaics and non-moisture-sensitive natural stone. It fills joints from 1.5mm up to 15mm wide.How to useThe kit comes in three parts: Part A resin, Part B hardener and Part C coloured filler, mixed at approximately 2 : 1 : 5-7 by volume. Mix only what you can use within the working time, work the grout firmly into clean, dry joints with an epoxy float, then emulsify and clean the surface promptly with a lightly damp sponge before the epoxy sets. Finish by polishing the tiles once dry. Mix part-kits accurately if you split the kit across sessions.Important notesEpoxy grout sets chemically, so cleaning off residue promptly is essential - hardened epoxy is very difficult to remove from tile faces. Coverage varies with tile size and joint dimensions; as a guide a kit does approximately 8m² of 200 x 200 x 8mm tiles at 3mm joints.Specifications Joint width 1.5 - 15mm Coverage guide Approx. 8m² per kit for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, vitrified, mosaics, non-moisture-sensitive stone Location Walls and floors, indoor and outdoor SafetyEpoxy resins and hardeners can cause skin and eye irritation and sensitisation. Wear gloves and eye protection, ensure good ventilation, avoid skin contact with uncured components, and wash immediately after any contact. Keep out of reach of children and read the Part A, Part B and colour pack Safety Data Sheets before use.
$103.97 - $114.00
Dunlop Ready-to-Go Tile & Grout 250g (White) is a clever 2-in-1 product that works as both a tile adhesive and a grout, straight from the tube. There is nothing to mix and very little mess, which makes it a go-to for small tiling jobs, mosaics and quick repairs or touch-ups around the home. Backed by Dunlop's 10 year guarantee. 2-in-1 ready-to-use tile adhesive and grout No mixing, no fuss, less mess Contains Grout Shield antifungal protection Ideal for mosaics, repairs and touch-ups Suitable for joint widths of 1-5 mm Indoor and outdoor wall use About the formula This white, pre-mixed paste bonds wall tiles and then fills the joints with the same material, so a single tube handles the whole repair. The built-in Grout Shield technology helps resist mould and bacteria, keeping finished joints looking cleaner for longer. Excess can simply be wiped away with a damp cloth while still fresh, and the resealable tube makes it easy to store for future touch-ups. Where to use it Indoors: wall tiles and mosaics in kitchens, splashbacks, laundries and living areas, plus general tile and grout repairs. Suitable over concrete, cement render, fibre-cement sheet, plasterboard and prepared painted surfaces. Outdoors: exterior wall tiles and mosaics. When grouting outdoors, protect the area from extremes of weather for 7 days while it cures. Tile types: ceramic, porcelain and marble wall tiles and mosaics (excluding moisture-sensitive stone). How to use it Prepare the surface so it is flat, firmly fixed, clean and dry, free of dust, oil, grease and loose material. Prime surfaces with Dunlop Primer & Additive and allow to dry. Spread the adhesive with a 4.5-6 mm notched trowel to a minimum 1 mm bed. Press and slide each tile into position for full contact, adjusting within 60 minutes (at 23°C, 50% humidity). Joints can be grouted immediately. Squeeze the material firmly into the joints and compact with a grout float or squeegee, scraping off excess from the tile face. After about 15 minutes, wipe back excess with a damp, small-pored sponge, rinsing often. Once the joint has hardened (approx. 6-24 hours), buff and polish the tiles with a clean, dry cloth. Important notes Not suitable for use in wet areas such as a shower recess, over Dunlop Waterproofing membrane, or in continuously immersed conditions. Do not use the grout in expansion or movement joints. For textured or matt tiles, test ease of cleaning on a spare tile first. Designed for wall tiles and mosaics rather than heavy floor tiling. Specifications Brand Dunlop Product Ready-to-Go Tile & Grout (2-in-1) Colour White Size 250 g Form Pre-mixed, ready-to-use paste Tile types Ceramic, porcelain, marble, mosaics (excl. moisture-sensitive stone) Surfaces Walls Location Indoor and outdoor Joint width 1-5 mm Clean up Water (while fresh) Guarantee 10 year (Ardex Australia) Safety Causes skin irritation and may cause an allergic skin reaction. Causes serious eye damage and may cause respiratory irritation. Use only outdoors or in a well-ventilated area, and wear protective gloves, clothing, eye and face protection. Avoid breathing any mist, vapour or spray. Refer to the Safety Data Sheet (SDS) for full details.
$16.88
Glitz Daily Shower Cleaner Prevents Soap Scum Build Up 750ml Keep your shower looking fresh with this easy daily spray. Glitz Daily Shower Cleaner helps prevent soap scum and mineral build up so glass, tiles, and fittings stay clearer for longer. No heavy scrubbing required. Just spray and go as part of your routine. Key benefits Helps stop soap scum forming between deep cleans Cuts through light residue from body wash and shampoo Streak free finish on shower screens when used as directed Fast application for busy bathrooms Fresh clean scent that leaves the space smelling pleasant Where to use Shower glass and screens Ceramic tiles and grout surrounds Fibreglass and acrylic bases Chrome and stainless steel fittings Sealed stone and laminate surfaces in wet areas Always test first on an inconspicuous spot. Avoid unsealed stone, marble that is not sealed, brass, copper, and any surface that is not water safe. How to use After showering, quickly rinse surfaces with warm water. Set nozzle to spray. Mist evenly over glass, tiles, and fittings. Leave to work. No rinse required on light residue. For heavier build up, wipe with a soft cloth or squeegee. Use daily to help prevent soap scum returning. Pro tips Keep a squeegee in the shower and pull down glass before spraying for the best clarity. Ventilate the bathroom to reduce fogging and moisture marks. Pair with a weekly deep clean for grout lines and corners. Good to know Non abrasive formula suitable for regular use Safe for most sealed surfaces when used as directed Family friendly routine cleaner for shared bathrooms Specifications Product Daily shower maintenance spray Size 750 ml trigger bottle Suitable surfaces Glass, ceramic tile, acrylic, fibreglass, chrome, stainless steel, sealed stone Finish Clear streak free when wiped or squeegeed Use frequency Daily after showering Safety Read label before use. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other cleaners. Store upright in a cool dry place. Frequently asked questions Do I need to rinse after spraying For light daily residue, no rinse is needed. For visible build up, wipe or squeegee for a clear finish. Will it remove heavy limescale It is designed to prevent and control light residue. For stubborn limescale, use a suitable descaler first then maintain with daily use. Is it safe on natural stone Use only on sealed stone. Test first and avoid unsealed or delicate stone surfaces. What is in the box 1 x 750 ml Glitz Daily Shower Cleaner with adjustable trigger
$11.61 $11.28
Protite Mould Defender Anti-Fungal Paint Additive 75 mL is a reliable liquid paint additive that helps inhibit mould growth in humid areas chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 75 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Protite Mould for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Protite Mould Defender Anti-Fungal Paint Additive 75 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms and laundries Kitchens and food prep zones Rental refresh and maintenance work Suitable surfaces The adhesive works well on the following surface types when properly prepared: Walls and ceilings coated with water based paint Suitable primers as per paint maker guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of Work to normal paint tray timelines. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix thoroughly into your chosen paint and apply as directed by that paint. Dry and recoat times follow the paint system. Temperature and environmental performance Use within the temperature window recommended for the host paint. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean rollers and brushes according to the paint manufacturer's advice. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store upright with cap tight. Do not allow to freeze or overheat. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.64
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$24.57
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
![Selleys No Mould Silicone Selant 100ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-selant-100ml-white-2.png?v=1792406202&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
![Selleys No Mould Silicone Selant 100ml [Translucent] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-mould-silicone-selant-100ml-translucent-2.png?v=1792406193&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-more-gaps-filler-bathroom-and-kitchen-white-2.jpg?v=1792406110&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$14.99
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$23.38
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$9.33
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$185.00
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.61
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
![Monarch Mini Silicone Mould Resistant [Translucent] (2)](http://gluesaustralia.com.au/cdn/shop/files/monarch-mini-silicone-mould-resistant-translucent-2.png?v=1792405534&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$6.28
Bostik Seal it Kitchen & Bathroom Translucent: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Grunt Shock Cord 8mm x 20m in black is a stretchy, hard-wearing cord for securing tarps, covers and loads, supplied as a long 20 metre length so you can cut it to suit each job. It has a latex rubber core inside a braided outer jacket, giving it the stretch and recovery that makes it handy anywhere a fixed rope is too unforgiving.About the productThe rubber core absorbs shock and keeps tension on whatever you are holding down, while the braided jacket protects the core from rubbing and wear. The cord is UV protected and is resistant to oil, petrol, rot, mildew and general weathering, so it copes well with life outdoors. The 8mm thickness suits heavier securing jobs where a thinner cord would feel light.Where to use itIndoors: making bungee-style cords and ties for storage, workshop and garage tasks.Outdoors: holding down tarps and tarpaulins, and securing trailer, boat and caravan covers, marine canopies and similar covers.How to use it Cut the cord to length with sharp scissors or a knife. A quick pass with a flame or hot blade is a common way to stop the ends fraying. Fit hooks, clips, cord buttons or end toggles of a suitable size, or tie the ends off with a secure knot. Work the cord around the load or cover and stretch it to take up the slack, so the tension is firm without overstretching. Check the cord and anchor points from time to time and replace the cord if the jacket wears through or the cord loses its stretch. Important notesShock cord is designed for holding and tensioning light to moderate loads and covers. It is not a rated lifting, towing or safety line and should not be used where a failure could cause injury. Stretched cord can snap back, so keep your face and others clear when fitting or releasing it, and wear eye protection if you are working under tension.Specifications Brand Grunt Product Black Shock Cord Diameter 8mm Length 20m Colour Black Material Latex / rubber Construction Braided jacket Resistance UV, oil, petrol, rot, mildew and weathering Use Indoor and outdoor Care and storageKeep the cord clean and dry, and rinse off salt, dirt or oil with fresh water if it gets grubby. Store it coiled, out of prolonged direct sunlight and away from sharp edges. Inspect it before each use and replace it if it is cut, frayed or no longer stretches back properly.
$34.91
Grunt Shock Cord is a stretchy, black latex rubber cord with a braided outer jacket, supplied here as an 8mm x 5m length for securing tarps, covers and loads. The elastic core absorbs shock and keeps tension on whatever it is holding, which makes it a handy general-purpose cord for the shed, the boat, the trailer or the caravan.About the productThe core is made from latex rubber and is wrapped in a braided jacket designed to resist abrasion. The cord is UV protected for outdoor use and is resistant to oil, petrol, rot, mildew and general weathering. The 8mm diameter is the thicker option in the Grunt shock cord range.Where to use itIndoors: making your own bungee cords, tying down stored items, and general securing jobs around the garage or workshop.Outdoors: holding down tarpaulins, and fitting trailer, boat and caravan covers or canvas.How to use it Cut the cord to the length you need with sharp scissors or a utility knife. Pair it with hooks, cord ends or shock cord buttons to make custom bungee cords. Run it across the load or cover, stretch it to take up the slack, then hook or tie it off at a secure anchor point. Seal or melt the cut ends if you want to stop the jacket from fraying (take care with heat). Important notesThis is a general-purpose elastic cord and is not rated for lifting, towing or safety-critical load restraint. Check the cord, anchor points and fittings regularly. Replace the cord if you see cuts, a worn jacket or a loss of stretch. Make sure the load is properly secured and legal for transport.Specifications Brand Grunt Product Shock Cord Model number GRROPE0116 Diameter 8mm Length 5m Colour Black Material Latex rubber core Construction Braided jacket Use Indoor and outdoor Care and storageStore the cord loosely coiled in a cool, dry place out of prolonged direct sunlight when not in use. Keep it away from sharp edges and from hot surfaces such as exhaust parts. Wipe off dirt and salt with fresh water and let it dry before storing.
$11.52
Grunt Black Shock Cord is a 6mm braided elastic cord supplied in a 20m length, made for tying down and securing tarps, trailer loads and boat or caravan covers. The stretch-and-recover action absorbs jolts and keeps a cover snug, so it suits bungee-style jobs where a fixed rope would work loose.About the productThe core is latex rubber, wrapped in a braided jacket built to resist abrasion. The jacket is UV protected and the cord is made to cope with weather, sunlight, oil, petrol, rot and mildew. That makes it a practical multi-purpose cord for outdoor use. The black finish suits most tarps, covers and trailers.Where to use itIndoors: garage, shed and workshop jobs such as holding bundled items, making your own bungee cords or securing tarps over stored gear.Outdoors: holding down tarpaulins, trailer covers, boat covers and caravan covers, plus general tie-down and camping tasks.How to use it Cut the cord to the length you need with sharp scissors or a utility knife. Fit hooks, clips or toggles, or tie it off with a knot that suits the job. Stretch the cord evenly across the cover or load, then anchor it at a secure point. Check the tension and the anchor points from time to time, especially after windy weather or a long trip. Important notesShock cord is intended for securing light covers and loads. It is not suitable for lifting, towing or safety-critical applications. Do not stretch it beyond a comfortable working range. Make sure the cord is firmly anchored, because a cord that slips or snaps can recoil quickly. Cord that is cracked, frayed or has lost its stretch should be replaced.Specifications Brand Grunt Product Shock Cord Size 6mm x 20m Colour Black Material Latex / rubber core Construction Braided jacket Model number GRROPE0115 Resistance UV, oil, petrol, rot, mildew and weathering Use Bungee cords, tarps, trailer, boat and caravan covers Care and storageWear eye protection when stretching or releasing the cord under tension, and keep it away from sharp edges that could cut the jacket. Rinse off salt, dirt or oil and let the cord dry before storing it. Store coiled in a cool, dry place out of prolonged direct sunlight when not in use.
$24.92
The Grunt 4mm x 20m Black Shock Cord is a long roll of stretchy, hard-wearing bungee cord for tying down tarps and covers and for general securing jobs around the home, trailer, boat or caravan. A rubber core gives it the give needed to absorb shock and keep tension, and a braided outer jacket protects the core from wear.About the productThe cord is made from latex rubber with a braided jacket. The manufacturer says it is UV protected and resists oil, petrol, rot, mildew, sunlight and general weathering. At 4mm thick it suits light to medium tie-down and bundling work, and the 20m length lets you cut your own bungees to whatever size you need.Where to use itIndoors: making custom bungee cords, bundling or holding items in sheds, garages and workshops, and general hobby or craft securing.Outdoors: holding down tarpaulins, and securing trailer, boat and caravan covers, camping gear and canopies.How to use it Measure and cut the cord to length with sharp scissors or a knife. Allow extra length for the knots or end fittings you plan to use. Finish the ends with secure knots, hooks, clips or cord ends. Stop the ends from fraying by sealing or fitting end caps if you want a tidy finish. Stretch the cord over the load or cover and fix it to a secure anchor point so it sits snug without being overstretched. Check the cord regularly and replace it if the jacket is worn, cut or the core looks damaged. Important notesThe manufacturer has not published a load rating or stretch limit for this cord, so do not use it for lifting, towing or any application where failure could cause injury. Overstretching, sharp edges and heavy wear will shorten its life. Take care when releasing a stretched cord, as it can snap back.Specifications Brand Grunt Product Shock Cord (Bungee Cord) Size 4mm diameter x 20m length Pack 1 roll Colour Black Material Latex / rubber core Construction Braided jacket Resistance UV protected; resists oil, petrol, rot, mildew and weathering Use Interior and exterior Care and storageKeep the cord coiled and dry when not in use, and wipe off dirt, salt or oil before storing. Keep it away from sharp edges and out of reach of children. Inspect it before each use and replace it if it shows signs of wear.
$19.94
Grunt Shock Cord 4mm x 5m in black is a stretchy, braided-jacket elastic cord for tying down and securing tarps, covers and loads around the home, trailer, boat or caravan. It is a handy multi-purpose length for making your own bungee-style ties, with enough give to absorb jolts and keep a cover snug.About the productThe cord has a rubber (latex) core wrapped in a braided outer jacket. The core provides the stretch and recovery, while the jacket is designed to resist abrasion. Grunt describes it as UV protected and resistant to oil, petrol, rot, mildew, sunlight and general weathering, so it suits outdoor use where a rigid rope would not cope with movement.Where to use itIndoors: bundling and securing items in the shed or garage, and making simple elastic ties for storage and DIY projects.Outdoors: holding down tarpaulins, and securing trailer, boat and caravan covers, as well as camping gear and loads.How to use it Cut the cord to the length you need with sharp scissors or a knife. Tie secure knots at each end, or fit hooks or fittings that suit a 4mm cord. Stretch the cord over the cover or load and anchor it so there is gentle, even tension. Check the cord regularly and replace it if the jacket is frayed or the cord has lost its stretch. Important notesShock cord is intended for light-duty securing and is not a rated tie-down, lifting or safety line. A stretched cord can snap back suddenly if it slips or a knot lets go, so keep your face and eyes clear when stretching and releasing it. Do not over-stretch the cord, and avoid sharp edges that can cut the jacket.Specifications Brand Grunt Product Shock Cord Size 4mm diameter x 5m length Colour Black Material Latex / rubber core Construction Braided jacket Resistance UV, oil, petrol, rot, mildew and weathering Recommended use Bungee cords, tarpaulins, trailer, boat and caravan covers Use Indoor and outdoor Care and storageRinse off salt, dirt or grime with fresh water and let the cord dry before storing. Keep it in a cool, dry place out of prolonged direct sun when not in use, and away from sharp objects. Keep out of reach of children.
$6.48
Feast Watson Outdoor Furniture Oil in Clear is a penetrating timber oil made to protect outdoor furniture while keeping the natural look of the wood, supplied here in a 1L can. It soaks into the surface rather than sitting on top, so it leaves a natural matt finish that lets the grain and texture show through.About the formulaAn oil-based, one-component formula enriched with eucalyptus oil. It is designed to resist mould and to give excellent water resistance, and the film is penetrating, so it is not expected to crack or flake. The Clear colour keeps the timber's own tone. It is not recommended for direct sunlight or extreme conditions. If you want a higher level of UV protection, choose one of the tinted colours in the range (Hardwood, Jarrah, Teak or Weathered Grey).Where to use itIndoors: not the intended use, as this oil is made for outdoor timber.Outdoors: timber outdoor furniture such as chairs, tables and benches, plus timber BBQ trolleys.Suitable for exterior timber furniture. Test a small, hidden area first if you are unsure how your timber will look.How to use itClean the furniture first with Feast Watson Woodclean to remove dirt, oil, wax and grease, then let it dry fully. Stir the oil thoroughly before and during use so the colour stays even. If you need more than one can, combine them in a larger container first. Apply the first coat with a quality brush, working in sections along the grain and fully coating edges and end grain. A roller or applicator pad can also be used. Let the oil soak in, then wipe off any excess with a brush or clean cloth. Leave it for 12 hours before applying a second coat. For chairs and benches, start on the inside of the legs, then move up to the seat and finish with the back. Clean brushes and tools with mineral turpentine.Important notesAllow about 12 hours between coats. Touch dry time is around 6 hours at 25°C and 50% humidity, and cooler or more humid conditions will take longer. Do not apply below 10°C, in very hot weather, or when rain or heavy dew is expected while the coating dries. Two coats are recommended, and the manufacturer lists a spread rate of about 6m² per litre, which varies with the timber. Over time, watch for colour loss, dryness and weathering. When that happens, clean with Woodclean and apply one maintenance coat. Soak used rags and cloths in water before disposing of them.Specifications Brand Feast Watson Product Outdoor Furniture Oil Size 1L Colour Clear Base Oil-based, with eucalyptus oil Finish Matt Application Brush, roller or applicator pad Coats 2 Recoat time 12 hours Spread rate About 6m² per litre Minimum application temperature 10°C Clean up Mineral turpentine Use Exterior timber furniture, BBQ trolleys and benches SafetyUse in a well-ventilated area and keep away from heat, sparks and open flame. Avoid contact with skin and eyes, and wear gloves and safety glasses while working. Keep out of reach of children and store the sealed can in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$74.61
![Cabot's Aquadeck Exterior Decking Oil 4L [Merbau] (2)](http://gluesaustralia.com.au/cdn/shop/files/cabot-s-aquadeck-exterior-decking-oil-4l-merbau-2.jpg?v=1792411934&width=645)
Cabot's Aquadeck in Merbau is a water-based, low odour decking oil that protects and enriches exterior timber, supplied here in a 4L pack for decks, pergolas, fences and outdoor furniture. It combines natural oils with an acrylic protective layer, and Cabot's says it lasts twice as long as traditional oil-based decking oils when applied as directed.About the formulaAquadeck uses a dual technology approach. Natural oils soak into the timber to nourish it, while an acrylic barrier forms on the surface to help guard against UV, water, dirt and mould. The Merbau shade gives a lightly pigmented, semi-transparent, matt finish that lets the grain show through. It is water-based, so tools clean up with water, and it is splatter resistant.Where to use itIndoors: not intended for interior use.Outdoors: timber decks, pergolas, fences, gates, screening and garden furniture.Suitable for new, weathered or previously coated exterior timber. Existing coatings can be recoated without sanding if they are at least 30 days old and in good condition.How to use itPreparation depends on the timber: New bare timber: scrub the damp timber with Cabot's New Timber Prep to draw out tannins and oils, then wash with Cabot's Deck Clean. Squeegee off excess water and let the timber dry for at least 1 hour (longer in cool conditions). Alternatively, let new timber weather for 4 to 6 weeks (about 2 weeks for new treated pine, or follow the timber maker's advice), then clean with Deck Clean. Previously coated with Aquadeck: clean with Cabot's Deck Clean. Other existing coatings (oiled, stained, varnished or painted): treat with New Timber Prep, then clean with Deck Clean for the best adhesion. Weathered or grey timber: clean with Deck Clean. Stir thoroughly with a broad, flat paddle before and during use. Apply with a brush or a Cabot's decking applicator. Apply two coats and leave about 1 hour between coats. For harsh exposure such as full sun or pool surrounds, apply three coats. Fill any holes or imperfections with a suitable timber putty after the first coat. Clean tools with water.Important notesThe final look depends on the condition and colour of any existing coating. If the old coating is peeling, flaking, uneven or darker than the Merbau shade, strip it or sand back to bare timber, then clean with Deck Clean. Use at temperatures of 10°C or above. Cooler conditions slow drying. Check coated timber about every 12 months, as water repellency and colour will change with weathering. Not for interior use.Specifications Brand Cabot's Product Aquadeck Exterior Decking Oil Size 4L Colour Merbau Base Water-based Finish Matt, semi-transparent Application Brush or Cabot's decking applicator Touch dry 20 minutes Recoat time 1 hour Coverage 12 m² per litre Minimum application temperature 10°C Clean up Water Use Exterior only SafetyWork in a well-ventilated area and avoid contact with eyes and skin. Wear gloves and safety glasses when applying. Keep out of reach of children and store the container sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$125.81
Crommelin Silicone WP Plus is a neutral cure silicone sealant made for wet areas, and it doubles as a bond breaker in Crommelin liquid applied waterproofing systems. This white 300g cartridge suits kitchens, bathrooms, laundries and similar jobs. It stays permanently flexible once cured and contains a mould and mildew inhibitor, so it holds up well in damp, steamy spaces.About the formulaA one-part, neutral cure silicone, so there is no mixing. The neutral cure chemistry will not corrode concrete or zinc coated and galvanised steel. It has a sag resistant body that can be used in vertical and overhead joints. Once cured it resists weathering, UV and vibration, and it is suitable for contact with aluminium shower screens. It can be used as a bond breaking sealant at joints, junctions and corners under waterproofing membranes, or as a durable finishing sealant.Where to use itIndoors: around showers, bath tubs, sinks, laundry fixtures, sanitary ware and spas, plus bond breaking joints in wet area waterproofing.Outdoors: exterior finishing joints and roof and gutter sealing, where the sealant is exposed to weather.Suitable materials include glass, glazed tiles and ceramics, steel and aluminium (suitably prepared), concrete, render, brickwork and blockwork, natural stone, fibre cement sheet and plasterboard. Use it only on clean, sound surfaces.How to use itMake sure the joint is clean, dry and free of dust, grease, soap residue and loose material. Cut the nozzle to suit the joint size, load the cartridge into a caulking gun and apply a continuous bead, then tool it smooth. Where it is used as a bond breaker in a waterproofing system, apply it at all joints, junctions, angles and internal corners before the membrane goes on. Refer to the Crommelin technical data sheet for full application guidance.Important notesThe cured silicone is not paintable, and it should not be used on freshly painted surfaces. Do not use it where it will contact food or potable water. Avoid materials that bleed oils, plasticisers or solvents, because they can affect adhesion. Keep it away from the silver backing of mirrors, such as at mirror edges. It is not a fire rated sealant. Silicone needs moisture in the air to cure, so it will not cure in a sealed, moisture-free environment.Specifications Brand Crommelin Product Silicone WP Plus (Silicone & Bond Breaker) Pack 1 x 300g cartridge (300ml) Colour White Base Neutral cure silicone, one part Application Cartridge, via caulking gun Features Mould and mildew resistant, permanently flexible, UV and weather resistant, sag resistant Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses where sensible. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$16.71
Soudal Bathroom & Kitchen Neutral Cure Silicone in clear is a pure silicone sanitary sealant for wet areas, supplied as a 300ml cartridge for use in a standard caulking gun. It is built for the joints that take the most punishment around showers, baths, sinks and benchtops, giving a waterproof seal that stays flexible and resists mould and mildew.About the formulaA neutral cure, non-corrosive silicone made from pure silicone with no extenders. It contains fungicides to help the seal resist mould and mildew in demanding sanitary conditions. It is easy to apply and tool, has a longer working time for smoothing joints, and stays permanently elastic once cured. The cured seal is colourfast and UV resistant, with a low modulus and a joint movement capability of +/- 25%.Where to use itIndoors: joints around bathtubs, vanities, shower screens, sinks, basins and toilets, kitchen splashbacks and benchtop joints, and sealing around plumbing fixtures in kitchens, bathrooms and laundries.Outdoors: not specifically recommended by the manufacturer for this product. Check the manufacturer data sheet or choose a product made for exterior use.Suitable materials include glass, tiles, fibreglass, vitreous enamel and many other common building and sanitary surfaces. Test an inconspicuous area first on any surface you are unsure about.How to use itMake sure the joint is clean, dry and free of dust, grease, soap scum and old sealant. Cut the nozzle to suit the joint, load the cartridge into a caulking gun and apply a steady, continuous bead. Smooth the bead with a profiling tool or a soapy water solution before the surface skins over, then remove any masking tape. Wipe away uncured excess promptly. Once cured, silicone has to be cut or scraped away.Important notesCure time depends on temperature, humidity and bead thickness, so allow plenty of time before exposing the joint to water. Keep joints well ventilated while curing. Always follow the manufacturer's instructions and test compatibility on sensitive materials before sealing.Specifications Brand Soudal Product Bathroom & Kitchen Neutral Cure Silicone Pack 300ml cartridge Colour Clear Base 100% silicone, neutral cure, no extenders Application Cartridge, via caulking gun Movement capability +/- 25% Key features Mould resistant, waterproof, non-corrosive, colourfast and UV resistant Use Bathrooms, kitchens and other wet areas SafetyWash exposed skin thoroughly after handling and wear suitable gloves and eye protection. Store locked up and dispose of contents and container in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$10.38
Ideal DIY Floors Indoor / Outdoor Carpet Tape is a double-sided adhesive tape for fixing marine carpet, synthetic grass and utility carpet, supplied here as a single 38mm x 12.8m roll. It suits jobs where the carpet is exposed to moisture and weather, such as boats, patios and outdoor areas, as well as general indoor carpet fixing.About the tapeThis is a double-sided adhesive tape built on a tear-resistant fibreglass carrier, so it holds together when you unroll and position it. The manufacturer describes it as water resistant, mildew resistant and rot proof, which is what you want when carpet sits in damp or exposed spots. It is designed to grip well on rough surfaces, provided they are clean.Where to use itIndoors: securing utility carpet and similar floor coverings to clean, rough surfaces.Outdoors: fixing marine carpet, synthetic grass and outdoor utility carpet where weather resistance matters.It is intended for use with marine carpets, synthetic grass and utility carpets. Test a small area first if your carpet backing or floor surface is unusual.How to use itClean the surface so it is free of dust, dirt, oil, grease and loose material, and make sure it is dry. Work within the recommended application temperature range. Cut the tape to length, stick it down along the area to be fixed, and press it firmly along its full length. Then lay the carpet or turf into place and press it down firmly so it contacts the tape evenly.Important notesApply the tape between 10°C and 30°C. The supplied product data lists this tape as not UV resistant, so consider this for areas in constant, direct sun. Rough surfaces need to be clean for the adhesive to perform at its best. Dusty, oily or loose surfaces will weaken the hold. Check suitability on your specific carpet backing and surface before committing to a large job.Specifications Brand Ideal DIY Floors Product Indoor / Outdoor Carpet Tape Size 38mm wide x 12.8m long Type Double-sided adhesive tape Carrier Tear-resistant fibreglass Application Hand applied, cut to length Application temperature 10°C to 30°C Resistance Water resistant, mildew resistant, rot proof UV resistance Not rated as UV resistant Use Indoor and outdoor SafetyKeep the tape away from young children, store the roll in a cool, dry place out of direct sunlight, and avoid contact with eyes. Wash hands after handling if the adhesive gets on your skin. Refer to the Safety Data Sheet (SDS) for full details.
$17.43
Crommelin DiamondTough Stone Shield Clear Sealer is a premium waterborne sealer made for dense natural stone, supplied here in a 1L pack that suits benchtops, feature walls and smaller floor areas. It protects against stains and water, dries clear, and leaves a natural to low sheen finish. Crommelin previously sold it as DiamondCoat Stone Shield. The brand says only the name has changed, not the product.About the formulaA water-based sealer that both penetrates the surface and forms a thin protective film, while still letting the stone breathe. It resists staining and abrasion and repels water well. It also contains an anti-microbial additive that helps stop mould and algae growing on the sealed surface. It is low odour and low VOC, dries quickly, and can be recoated soon after the first coat. It can be applied to vertical and horizontal surfaces.Where to use itIndoors: dense stone floor and wall tiles, stone and concrete benchtops, kitchens and living areas, and polished concrete.Outdoors: natural stone cladding and other exterior dense stone surfaces that suit a clear, low sheen protective coat.Suitable surfaces include granite, marble, bluestone, travertine, porcelain, polished concrete, terracotta, reconstituted stone and natural quarry stone. Always test a small patch first to check the colour enhancement, finish and slip resistance.How to use itThe surface must be clean and fully dry before you start. Crommelin requires a moisture test every time. If the surface has been acid etched, neutralise and rinse it thoroughly first. Apply the first coat evenly with a clean, lint-free tool so the surface is wet but no white excess liquid is left standing. Suitable tools are a brush, a roller, a lambswool applicator, a lint-free cloth or an airless sprayer. Apply the second coat in the same way once the first is touch dry, and within 2 hours. On very dense surfaces such as polished marble, the sealer may only need to be wiped on. If streaky film builds up on a dense surface once dry, wash it with warm soapy water, rinse and buff with a soft cloth. Clean tools with warm water and a little detergent straight after use.Important notesDo not apply when it is too hot or cold, when humidity is high, or when rain is expected within 48 hours. Allow about 24 hours before light foot traffic. Full cure takes around 7 days. Over-applying can leave a visible film on very dense stone, so work thinly and use a test patch to confirm the right rate. This product is a clear sealer. It cannot be tinted.Specifications Brand Crommelin Product DiamondTough Stone Shield Clear Sealer Pack 1L pail Colour Clear when dry Base Waterborne Finish Natural to low sheen Application Brush, roller, lambswool applicator, lint-free cloth or airless spray Recoat As soon as the first coat is touch dry, within 2 hours Light foot traffic About 24 hours Full cure About 7 days Application temperature 5 to 35°C Coverage Roughly 10 to 30 m² per litre, depending on how dense the surface is Primer required No Tintable No Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, avoid breathing spray mist, and wear suitable protective clothing, gloves and eye protection when spraying. Keep the container sealed and store it in a cool, dry place. Keep it out of reach of children, and do not let it enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$49.55
Gyprock Wet Area Acrylic Sealant is a white, paintable acrylic sealant made for bathrooms, laundries and other wet area builds, supplied here as a single 450g tube. It is designed to give plasterboard and wet area linings a long-lasting, flexible seal where they meet shower bases, baths and plumbing fittings, and it also works as a general purpose gap filler.About the formulaA ready-to-use acrylic sealant that stays flexible once cured, so it can move with the joint instead of cracking. It contains an antifungal agent to help resist mould and mildew, and it has moisture resistant properties for use in damp rooms. It can be painted over once fully cured. It is manufactured in Australia for CSR Gyprock.Where to use itIndoors: sealing the edge of Gyprock Aquachek wet area lining against pre-formed shower bases and baths, sealing around plumbing penetrations and fittings, and filling general gaps and junctions in bathrooms, laundries and other damp areas.It suits both residential and commercial construction. It is intended for non-fire-rated wet area systems.Suitable materials include Hebel, concrete, masonry, brickwork, plasterboard, fibre cement, metal, timber and plastic substrates (test plastics on a small area first).How to use itMake sure the joint or gap is clean, sound and free of dust, grease and loose material before you start. Cut the nozzle to suit the size of the joint, run a continuous bead and press it into the gap so it contacts both sides. Smooth the joint, and keep your tools clean while you work. Let the sealant cure fully before you paint over it. Unopened tubes should be kept in a cool, dry place away from direct sunlight and below 30°C. Opened tubes may skin over near the opening, so discard any lump or skin and the remaining sealant can still be used.Important notesThis sealant is not designed for constant water exposure or for stopping active leaks. Do not paint until it is fully cured. It is not an easy-sanding product. Shelf life is 1 year from the date of manufacture. The manufacturer does not publish set, cure or coverage figures for this tube, so allow plenty of time before showering or painting and check the label for current directions.Specifications Brand Gyprock (CSR) Product Wet Area Acrylic Sealant Pack 1 x 450g tube Colour White Base Acrylic Application Tube, used with a caulking gun Specific gravity Approximately 1.55 VOC content 17g/L (as specified by GBCA) Shelf life 1 year from date of manufacture Paintable Yes, once fully cured Use Wet area sealing and general purpose gap filling Origin Made in Australia SafetyIn a fire, use carbon dioxide, foam, dry chemical or water spray, and note that heated decomposition may release carbon dioxide and acrid smoke. Store unopened tubes in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$17.77
Mandala Art Mosaic Grout Sealer & Waterproof Additive is a 1L acrylic-based liquid made for mosaic artists and hobbyists who want to strengthen, seal and waterproof their grout with a single product. It can be mixed into grout powder or brushed over finished work, which makes it handy for outdoor pieces such as birdbaths and pavers.About the formulaAn acrylic-based white liquid that adds strength and flexibility to grout. Used correctly, it gives the grout water resistance, helps reduce mould growth and deepens the grout colour. It leaves a slight sheen on the finished surface.Where to use itIndoors: mosaic artworks, craft projects and decorative pieces where you want stronger, sealed grout lines.Outdoors: birdbaths, outdoor pavers and garden mosaics that will be exposed to moisture.It can also be used as a surface sealer on wood and MDF, and on porous surfaces such as terracotta and ceramic.How to use itFor a waterproof grout, use the additive in place of the water when you mix your grout powder, then stir to a smooth, toothpaste-like consistency and apply as normal. For extra strength and durability, you can brush a final coat of the additive over the project once the grout has dried. As a surface sealer, brush it onto the clean, dry surface. Check the product label for mixing and drying details, as the correct method matters for good results.Important notesThe manufacturer does not recommend this product for large works such as swimming pools. Water resistance and waterproofing depend on correct use. Use as directed on the label, and do a small test on a spare piece first if you are unsure about a surface. Specific mixing ratios, drying times and coverage have not been confirmed here, so please follow the pack instructions.Specifications Brand Mandala Art Product Mosaic Grout Sealer & Waterproof Additive Model GSA Size 1L bottle Colour White liquid Base Acrylic Application Mixed into grout powder in place of water, or brushed on as a sealer Finish Slight sheen, enhances grout colour Use Indoor and outdoor mosaics SafetyAvoid contact with eyes and prolonged skin contact, use in a well-ventilated area, and wash hands and tools after use. If it gets in the eyes, rinse with plenty of water. Keep out of reach of children and store the container sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$30.29
Crommelin Blackseal Heavy Duty is a water-based, rubber-modified bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 1L size that suits planter boxes, pots, timber posts and small retaining wall jobs. It is made for surfaces that stay damp or wet and will not be painted, tiled or covered with a finishing coat.About the formulaCrommelin describes Blackseal as a commercial grade bitumen emulsion modified with a synthetic rubber co-polymer. The rubber modification keeps the cured film flexible, so it stays watertight under permanently wet conditions and is suitable for permanent immersion. It helps prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. It grips a wide range of substrates, is fast drying, and the maker lists it as non-toxic and non-flammable. It can be thinned with up to 50% water to make a bitumen paint.Where to use itIndoors: not intended for interior finishing work or any area that needs a paintable or tileable surface.Outdoors: below-ground and non-exposed exterior surfaces such as garden retaining walls, planter boxes, plant pots, timber posts, water tanks and other non-critical moisture barrier jobs.Suitable materials include concrete, masonry, cement sheeting, timber and metal (check the label for the full substrate list and do a small test area first).How to use itStart with a clean, sound surface free of dust, grease, loose material and anything that could stop the membrane bonding. Stir the product well and apply it evenly with a brush or roller, then allow it to dry before any further coats. Check the label and Crommelin's full instructions for coverage, coat numbers and drying times before you start, and protect the cured membrane from damage if you will be backfilling against it. Clean tools before the product dries (as a water-based product, warm water is the usual method, but confirm on the pack).Important notesNot suitable where it will be exposed to UV or sunlight. It cannot be painted, tiled over, rendered or over-coated, and it is not for trafficable surfaces. If you need a UV-stable option, look at a different Crommelin product. Coverage and cure times depend on the surface and conditions, so treat the listed coverage as a guide and test a small area first.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Size 1L Colour Black Base Water-based bitumen emulsion, modified with a synthetic rubber co-polymer Application Brush or roller Coverage Approx. 0.75 m² per 1L (retailer listed, guide only) Dilution Up to 50% water to make a bitumen paint Use Below-ground and non-UV-exposed exterior areas Not suitable for UV exposure, painting, tiling, over-coating, trafficable surfaces SafetyThe product itself is not combustible, but once the water has evaporated the organic components can burn or break down in a fire. Avoid contact with eyes and skin, keep out of reach of children, and wash off spills and splashes promptly. Refer to the Safety Data Sheet (SDS) for full details.
$20.75
Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$37.54
Dunlop Matte Silicone is a flexible acetic-cure sealant with an elegant matte finish, made for modern tiles and grouts where a shiny silicone bead would look out of place. Available in four designer colours — White, Grey, Silver Grey and Anthracite — it lets the sealant line sit quietly against matte porcelain, stone-look tiles and contemporary grout colours while still delivering strong adhesion and dependable waterproofing.Where to use itIdeal for wall and floor junctions, tiled surfaces, benchtops, bath edges, cupboards, splashbacks and movement joints up to 30mm wide. It is mould resistant, UV and weather resistant, and suitable for both indoor and outdoor use, including wet areas. It bonds well to ceramic tiles, glass, enamel, anodised aluminium, granite, porcelain and sanitary acrylics.How to usePrepare joints so they are clean, dry and free of dust, grease and old sealant residue. Cut the cartridge tip and nozzle to match the joint width, fit the cartridge in a caulking gun and run a smooth, continuous bead along the joint. Tool it off promptly before a skin forms, remove masking tape straight away, and let the silicone cure fully before use in wet areas.Important notesBeing an acetic-cure silicone, it must not be used under waterproofing membranes or with mirrors, as the cure can damage those surfaces — use a neutral-cure silicone there instead. Maximum joint size is 30mm wide by 15mm deep.Specifications Size 310ml cartridge Max joint width 30mm wide x 15mm deep Cure type Acetic cure silicone, matte finish SafetyEnsure good ventilation during application and avoid skin and eye contact with uncured sealant. Keep away from children and consult the Safety Data Sheet available from Dunlop Trade before starting work.
$30.99
You have seen 48 out of 81 products
Sealants and coatings formulated to resist mould growth in damp, frequently cleaned areas. Ideal for bathrooms, laundries and kitchens. Look for long-term flexibility and easy-clean finishes. Use filters to refine by chemistry and colour. Always check the product page and TDS/SDS for cure times before water exposure.
