A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$48.79
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$77.97
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.80
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0fda3f36-74b9-4f76-87c5-eecf1c56afcc.jpg?v=1754715680&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_3922d4f4-2f1d-4263-a2de-14b767df10ba.jpg?v=1754715681&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e4f50d8f-e0a6-4255-a242-9c3e7590f0f3.jpg?v=1754715675&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e401b93c-d8cb-46ff-be50-3f30c2495024.jpg?v=1754715675&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_84aa9bc6-f55e-40c0-afbe-820db6fddb04.jpg?v=1754715673&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0c7f6c0e-695e-4545-a57c-1e5bf7ca1f0c.jpg?v=1754715673&width=645)
$9.49
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$18.30
Bostik Glu Stik is the classic clear-drying glue stick that generations of Australian classrooms, craft rooms and home offices have run on. This listing is a bulk pack of ten 35g sticks, which is the economical way to buy for a school term, a busy studio, an office stationery cupboard or a community group that goes through glue faster than anyone expects.The formula is a solid, solvent free adhesive that glides on smoothly and dries clear, so finished work looks clean rather than patchy. It is acid free, which matters when you are mounting photographs or building a scrapbook that needs to survive a few decades without yellowing or corroding the materials underneath. The non-wrinkle characteristic means lightweight paper stays flat instead of buckling as the glue dries. The twist-up applicator keeps hands clean and lets you control how much stick is exposed at a time.Where to use itIndoors Scrapbooking, journaling and album building Cut and paste activities, school projects and classroom worksheets Paper craft, card making, collage and invitations Dry mounting photographs and artwork General office and stationery work on paper and light card OutdoorsNot recommended. This is a water soluble stationery adhesive with no weather or moisture resistance, so anything destined for outdoor exposure needs a different product.What it bondsPorous materials, including paper, cardboard, photographs, cellophane, crepe and tissue paper, foil and fabric. Surfaces need to be clean and dry for a reliable bond.How to use Check that both surfaces are clean and dry. Remove the cap and turn the base clockwise until a small amount of glue protrudes. Expose only what you need. Apply with firm, even strokes to one surface. Press the two surfaces together. Initial grab is roughly 20 to 40 seconds. Turn the base anti-clockwise to retract the glue and recap straight away so the stick does not dry out. Tip: if a stick has been left uncapped and has dried out, sitting it in warm water for a few minutes will usually bring it back rather than sending it to the bin.Important notes Designed for lightweight bonding. It is not suitable for heavy duty repairs or structural work. Not suitable for non-porous surfaces such as metal, glass or most plastics. No water resistance. Bonded work should be kept dry. Always recap after use. An uncapped stick will dry out. Store between 5°C and 30°C, out of direct sunlight. The formula contains corn starch. It is free from wheat, gluten, flour, egg and nut ingredients, though repeated or prolonged contact may cause an allergic reaction in susceptible people. Specifications Brand Bostik Product Glu Stik Pack 10 x 35g sticks Type Solid stick stationery adhesive Colour White stick, dries clear Solvent content Solvent free Acid free Yes Initial grab Approximately 20 to 40 seconds Clean up Warm soapy water Suitable surfaces Paper, cardboard, photographs, fabric Storage 5°C to 30°C, away from direct sunlight Compliance Tested to AS/NZS ISO 8124.3 (Safety of Toys, migration of certain elements) SafetyAccording to the Bostik Safety Data Sheet, Glu Stik is not classified as hazardous under GHS and carries no hazard statements. No poison schedule number is allocated under the SUSMP. It is non-toxic and solvent free, which is why it is cleared for classroom use, but it is still an adhesive and not a toy. Keep it out of reach of very young children, avoid eye contact, and do not eat it. If glue does get in an eye, rinse thoroughly with water immediately and seek medical advice if irritation continues. Wash residue off skin and surfaces with warm soapy water. Always read the label and the current Safety Data Sheet before use.
$43.00
Selleys BBQ Tough Grease & Grime Cleaner is a fast-acting spray made for the quick clean-up that keeps a barbecue in good shape. It lifts cooking grease, baked-on food and general grime from hotplates and grills so the cooking surface stays clean and hygienic, without the hard scrubbing a wire brush needs. The 500mL trigger bottle sprays an even coat straight onto the surface and is ready to use with no mixing or dilution. Formula overview The cleaner uses a surfactant-based, non-caustic formula, so it powers through fat and oily build-up while being easier to handle than harsh caustic products. It goes to work in two to three minutes, loosening the grease so it wipes away instead of needing to be scoured off. Because it is water based, any residue rinses and wipes off easily with a damp cloth. Where to use it Outdoors: BBQ hotplates, grills and racks are the main job, ideal as an after-cook clean while the plate is still slightly warm. It also works well on outdoor furniture and many other outdoor surfaces where grease and grime gather. Indoors: the same grease-cutting action can help on other greasy cooking-area surfaces, as long as they are not on the unsuitable list below. The product is formulated first and foremost for barbecue and exterior clean-up. How to use Warm the hotplate or grill slightly, then turn the BBQ off and check it is cool enough to touch. Spray directly onto the surface. Leave for two to three minutes so the formula can break down the grease. Wipe clean with a damp cloth or a Selleys BBQ Tough Wipe, then wipe again with a clean cloth to remove any residue. For heavier build-up, spray on and scrub lightly before wiping off. Cleaning each time you barbecue helps stop stubborn grime from forming. Important notes Do not use on BBQ decals, prints, signs, dial marks or clear plastics. Wipe off brass and painted surfaces straight away. Spot test on an inconspicuous area if you are unsure about a surface. Keep out of reach of children. Specifications Brand Selleys Product BBQ Tough Grease & Grime Cleaner Size 500mL Format Trigger spray bottle, ready to use Base Water based, surfactant based Appearance Colourless liquid Caustic No (non-caustic) Action time 2 to 3 minutes Clean-up Damp cloth and water Suitable surfaces BBQ hotplates, grills and racks; outdoor furniture Not suitable for Decals, prints, signs, dial marks, clear plastics; avoid leaving on brass or painted surfaces Safety According to the manufacturer's Safety Data Sheet, this product is classified as hazardous under Safe Work Australia criteria, with the signal word Warning. It can cause skin irritation and serious eye irritation and is harmful to aquatic life. Wear protective gloves and eye protection, wash your hands thoroughly after use, and avoid releasing it to the environment. If it contacts skin, wash with plenty of soap and water. If it gets in eyes, rinse cautiously with water for several minutes, remove contact lenses if present and easy to do, and keep rinsing; get medical advice if irritation persists. Keep out of reach of children and read the label before use. The product is not classified as a Dangerous Good for transport by road, rail, sea or air. If poisoning occurs, contact a doctor or the Poisons Information Centre (Australia 13 11 26).
$9.13
Dunlop Wide Joint Grout is a cement-based tile grout purpose-made for the big joints that standard grouts can't handle, filling gaps from 5mm right up to 50mm wide. In a practical Mid Grey colour, it suits rustic and heavy-duty tiling styles where wide grout lines are part of the look, curing to a hard-wearing finish indoors and out.Where to use itUse it on walls and floors, indoors and outdoors, over ceramic tiles, terrazzo, quarry tiles and sealed terracotta and slate. It is the go-to grout for terracotta paving, quarry tile floors, feature walls and any tiled area with generous joint widths.How to useMix the powder with clean water to a firm, workable consistency and work it into the joints with a grout float, compacting well so the full joint depth is filled. Strike off excess on the diagonal, then clean the tile faces with a damp sponge once the grout has firmed. Porous tiles such as terracotta and slate should be sealed before grouting to prevent staining.Important notesDesigned for joints 5-50mm wide; for narrower joints use Dunlop Flexible Coloured Grout. Coverage varies with tile size and joint dimensions. Protect fresh grout from rain and frost while curing.Specifications Size 15kg bag Colour Mid Grey Joint width 5-50mm Tile types Ceramic, terrazzo, terracotta, slate, quarry tiles Coverage Approx. 9m² (200x200x10mm tiles, 8mm joint) to 11m² (600x600x10mm, 20mm joint) per 15kg Location Indoor and outdoor, walls and floors SafetyCement-based powder - alkaline when wet. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the work area ventilated, avoid prolonged skin contact and wash hands after use. Keep out of reach of children.
$41.19
Dunlop Coloured Render Texture Coat is a premixed, coloured acrylic texture coat that delivers a durable, contemporary decorative finish straight from the pail. Tinted in a range of popular Colorbond® colours, it lets you match rendered walls to roofing, gutters and trims without painting afterwards. The easy trowel-and-float formulation applies like a render but finishes like a designer coating, and its protective acrylic film shrugs off weather for a long-lasting, low-maintenance facade.Where to use itFor indoor and outdoor decorative finishing over brick, blockwork, concrete, blueboard and compressed fibre cement sheet — typically as the final coat over a levelled base render such as Dunlop Multipurpose Acrylic Render or Flexible Fine Coat Render. Choose from Surfmist, Dune, Woodland Grey and Monument to complement your colour scheme.How to useEnsure the base surface is clean, dry, sound and uniform; make good any defects with Dunlop Render Joint & Patch first. Stir the pail thoroughly to an even colour, then apply with a steel trowel to a thin, consistent film of around 1mm. While still workable, rub up with a plastic float in a circular motion to develop the characteristic texture. Work wall sections wet-edge to wet-edge to avoid joins, and use pails from the same batch on a single elevation. Tools clean up with water. A 12.5L pail covers up to 10m² at 1mm thickness.Important notesColour consistency is best when complete walls are finished in one session from mixed batches. Avoid application in rain, extreme heat or onto damp substrates; drying slows in cold, humid conditions.Specifications Size 12.5L pail Colours Surfmist, Dune, Woodland Grey, Monument (Colorbond®) Coverage Up to 10m² at 1mm per pail Finish Coloured acrylic texture coat SafetyWater-based acrylic coating. Wear gloves and eye protection, avoid skin and eye contact and wash off with water while wet. Keep sealed and away from children, and consult the Safety Data Sheet before use.
$135.40
Dunlop Render Joint & Patch is a high-performance, two-in-one compound for rendering projects: it joints fibre cement sheet and blueboard before render is applied, and it patches cracks and holes in existing rendered surfaces up to 5mm deep or wide. Supplied premixed in a light grey colour that blends into most render systems, it takes the fuss out of preparation work — one pail handles both the sheet joints and the surface defects before your finishing coat goes on. The 4L size is perfect for repairs and smaller rendering jobs.Where to use itOn interior and exterior walls. As a jointing compound, use it over blueboard and fibre cement sheet prior to rendering. As a patching compound, use it over sound existing render to fill hairline cracks, chips, divots and small holes before re-coating or painting.How to useSurfaces must be clean, dry, sound and free of dust, loose render and contaminants. Stir the pail, then trowel the compound firmly over sheet joints (embedding tape where the sheet system requires) or press it into cracks and holes, striking off flush with the surrounding surface. Feather edges smooth with a trowel — the Dunlop Gauging Trowel gives a professional finish. Allow to dry fully before applying render, texture or paint, and wash tools in water straight after use.Important notesMaximum patch depth or width is 5mm — build deeper repairs in stages or use a repair mortar. Drying time lengthens in cold or humid conditions. Not intended for structural crack repair or designed movement joints.Specifications Size 4L pail Colour Light Grey Patch capacity Cracks and holes up to 5mm (depth or width) Location Indoor and outdoor walls SafetyWater-based compound — wear gloves and safety glasses, avoid skin and eye contact and wash off with water. Keep the pail sealed and out of reach of children, and read the Safety Data Sheet before use.
$65.35
Dunlop Render Joint & Patch in the 10L trade pail is a high-performance combination product that covers two essential preparation steps in one: jointing fibre cement sheet and blueboard ahead of rendering, and patching cracks and holes up to 5mm in existing rendered walls. Premixed to a smooth, light grey consistency, it goes straight from pail to trowel with no mixing, keeping preparation fast and consistent across large jobs. The 10L size is the economical choice for renderers and builders working across full elevations or multiple rooms.Where to use itIndoors and outdoors on walls. Use as a jointing compound over blueboard and fibre cement sheeting before render systems are applied, and as a patching compound over sound existing render to make good cracks, holes and surface defects up to 5mm deep or wide before re-rendering, texture coating or painting.How to usePrepare a clean, dry, sound surface free of dust, loose material and contaminants. Trowel the compound firmly across sheet joints, embedding jointing tape where required by the sheet manufacturer, and feather the edges flush. For patching, press the compound into the defect, strike off level and smooth the surface — the Dunlop Gauging Trowel helps achieve a professional finish. Allow to dry completely before over-coating, and clean tools with water while the product is still wet.Important notesRepairs deeper or wider than 5mm need staged applications or a dedicated repair mortar. Cold, damp or humid weather extends drying times. Do not use across designed movement joints — finish those with a flexible sealant.Specifications Size 10L pail Colour Light Grey Patch capacity Cracks and holes up to 5mm (depth or width) Location Indoor and outdoor walls SafetyWater-based product. Wear gloves and eye protection during use, avoid prolonged skin contact and wash exposed skin with water. Store sealed, keep away from children and consult the Safety Data Sheet before application.
$117.64
Dunlop Flexible FC Jointing Compound in the 8kg trade pail is a premixed, flexible jointing compound for fibre cement sheet and blueboard, formulated to prepare sheet joints before decorative coatings, texture finishes or render go on. Ready to use straight from the container, it removes mixing from the workflow entirely and keeps a consistent, workable body from the first trowel-load to the last. Its flexible acrylic formulation moves with the substrate to resist joint cracking, while strong adhesion keys the compound firmly to the sheet surface.Where to use itFor jointing fibre cement sheeting and blueboard on interior and exterior walls — cladding, facades, garage conversions, extensions and commercial sheeted walls — prior to painting, texture coating or rendering. The larger pail suits whole-wall and multi-room jobs where a 3kg pack would run short.How to useCheck that sheets are rigidly fixed and joints are clean, dry and dust-free. Apply the compound over each joint with a trowel or broad knife, embedding jointing tape where the sheet manufacturer requires it, then finish with a band approximately 75mm wide and 1mm thick, feathered smooth at the edges. Allow to dry completely before over-coating. Wet compound cleans off tools with water. Coverage is approximately 7 lineal metres per kilogram at 75mm width and 1mm thickness, so an 8kg pail joints in the order of 55 lineal metres.Important notesDesigned movement joints should be finished with a flexible sealant rather than jointing compound. Drying slows in cold or humid weather. Keep the lid sealed between uses and do not thin the product with water.Specifications Size 8kg pail Colour Grey Coverage Approx. 7Lm per kg (75mm wide at 1mm thick) Location Indoor and outdoor walls SafetyWater-based acrylic product. Wear gloves and eye protection during application, avoid prolonged skin contact and wash with water after use. Store sealed in a cool place away from children and refer to the Safety Data Sheet before starting.
$92.06
Dunlop Ready-to-Go Render is a premixed white render supplied in a resealable pail, ready to trowel straight onto the wall with no mixing, no dust and no wasted powder. Its easy trowel-and-float formulation makes it one of the most approachable renders for first-time renderers, while still giving experienced applicators a smooth, workable body. Applied at 1-5mm, it delivers a clean, uniform finish over a wide variety of common wall surfaces inside and out.Where to use itSuitable for indoor and outdoor projects over AAC panels and blocks, blueboard, brickwork, concrete walls and sound painted surfaces. Ideal for feature walls, fence walls, garden walls, patching over dated finishes and giving tired masonry a fresh, rendered look.How to useMake sure the surface is clean, sound and free of dust, oil and loose or flaking material; prime porous or painted surfaces as recommended. Stir the pail, then apply the render with a steel trowel to a thickness of 1-5mm, working in manageable sections. Rule off and finish with a float or sponge float once the render has firmed — the Dunlop Sponge Float gives a superior finish. For a higher build over uneven walls, first apply Dunlop Multipurpose Acrylic Render as a base coat and use Ready-to-Go Render as the finishing coat. Tools wash up in water.Important notesKeep within the 1-5mm application range per coat. Avoid rendering in direct hot sun, strong wind or when rain is expected; cold and humid conditions extend drying times. Reseal the pail to keep unused render workable.Specifications Size 16kg pail Colour White Coverage Approx. 6m² at 1mm or 2m² at 3mm per 16kg Application thickness 1-5mm SafetyWater-based premixed render. Wear gloves and safety glasses, avoid skin and eye contact, and wash with water after use. Keep out of reach of children and refer to the Safety Data Sheet for detailed handling information.
$120.29
Dunlop Tile Pointing is a flexible, premixed pointing compound that acts as a mechanical adhesive for hip and ridge roof tiles, exceeding the requirements of the relevant Australian Standards. Independently tested to achieve a C4 classification, it is approved for use in cyclonic regions, and its low-VOC formula resists mould and mildew while flexing with normal roof movement. Available in five roof-matched colours and backed by a 10 year guarantee, it is the straightforward way to re-point ridge capping and secure hip tiles without mixing mortar additives on site.Where to use itFor exterior roofing work only — pointing hip and ridge tiles over fresh or sound existing bedding on concrete and terracotta tiled roofs. Choose the colour that best matches your tiles: Slate Grey, Charred Ash, Jet Black, Sand or Terracotta.How to useBefore application, ensure all bedding material is in place and sound, and surfaces are clean and free of dust and loose mortar. Stir the pail contents, then apply the compound directly over the bedding with a gauging or pointing trowel, working it firmly against both the ridge tile and the roof tile surfaces to a thickness of roughly 3-5mm. Tool off to a neat finish. Wash tools in warm water immediately after use. Coverage is approximately 2 lineal metres per litre, so a 10L pail points roughly 20-22 lineal metres of ridging depending on technique.Important notesNever add water to Tile Pointing. Cold (below 10°C), damp or humid conditions lengthen drying time, while hot, windy weather can significantly shorten working time — avoid application if rain is imminent.Specifications Size 10L pail Colours Slate Grey, Charred Ash, Jet Black, Sand, Terracotta Coverage Approx. 2 lineal metres per litre (20-22Lm per pail) Application thickness 3-5mm Classification C4 - cyclonic region approved SafetyLow VOC, water-based compound. Wear gloves and eye protection, and take appropriate precautions when working at heights on roofs. Wash skin with warm water after contact and refer to the Safety Data Sheet before use.
$61.05
Dunlop Flexible FC Jointing Compound is a premixed, flexible compound for jointing fibre cement sheet and blueboard before decorative coatings are applied. Because it comes ready to use straight from the pail, there is no on-site mixing, no powder mess and no guesswork about water ratios — simply open, stir and trowel. The flexible formulation accommodates the minor movement typical of sheeted walls, while its excellent adhesion delivers a reliable, crack-resistant joint. The compact 3kg pail is ideal for smaller sheeting jobs and repairs.Where to use itUse on interior and exterior walls to finish joints between fibre cement sheets and blueboard prior to painting, texture coating or rendering. It is the recommended first step in preparing sheeted facades, extensions and infill panels for a decorative finish.How to useEnsure sheets are securely fixed and joints are clean, dry and free of dust. Where the sheet system requires it, embed jointing tape in a first application of compound. Apply the compound over the joint with a trowel or broad knife in a band roughly 75mm wide and about 1mm thick, feathering the edges smooth into the sheet face. Allow to dry fully before over-coating with paint, texture or render. Tools clean up with water while the compound is wet. Coverage is approximately 7 lineal metres per kilogram at a 75mm width and 1mm thickness — around 21 lineal metres from this 3kg pail.Important notesNot a structural adhesive or gap filler for moving joints wider than the system allows — use a flexible sealant at designed movement joints. Cold or humid conditions extend drying time. Reseal the pail after use to keep the remainder workable.Specifications Size 3kg pail Colour Grey Coverage Approx. 7Lm per kg (75mm wide at 1mm thick) Location Indoor and outdoor walls SafetyWater-based acrylic compound. Wear gloves and safety glasses, avoid skin and eye contact, and keep away from children. Wash hands and tools with water after use, and consult the Safety Data Sheet for full handling advice.
$42.06
Dunlop Grout Paint is the quick, budget-friendly way to make a tiled area look new again without raking out old or discoloured grout. The acrylic formula paints straight over existing grout lines with the built-in brush applicator, offering excellent opacity that covers even dark colours in a coat or two. Clean-up is easy, and a single 250ml bottle refreshes a surprisingly large area.Where to use itUse it over old or discoloured cement grout on indoor walls and floors and on outdoor walls. It is perfect for freshening bathrooms, kitchen splashbacks and laundry tiling, or for switching grout colour - brightening joints with Ultrawhite or going darker with Slate Grey or Jet Black for a modern contrast.How to useClean the grout thoroughly (Dunlop Tile & Grout Cleaner works well) and let it dry. Shake the bottle, then brush the paint along the grout line with the applicator, overlapping slightly onto the tile edge. Once touch dry - about 15-20 minutes at 23°C - wipe the overpainted edges off the tile faces with a damp cloth. Allow 2 hours' cure after cleaning, then polish the area with a soft cloth. The paint is fully set after 24 hours, after which showers can be exposed to water.Important notesNot suitable for swimming pools or external floors. Expect faster wear in areas with regular foot traffic or frequent exposure to water, soaps and chemicals such as shower floors. Coverage varies enormously with joint width and tile size - from about 1m² on small mosaic tiles with wide joints up to 200m² on large-format tiles with fine joints.Specifications Use on Old or discoloured grout joints Coverage guide Approx. 60m² per 250ml for 330 x 330mm tiles at 3mm joints Tile types Grout joints between most glazed ceramic and porcelain tiles Location Indoor walls and floors, outdoor walls SafetyAvoid contact with eyes and prolonged skin contact; wear gloves if desired and wash hands after use. Use with adequate ventilation, keep out of reach of children and refer to the Safety Data Sheet.
$18.71
Dunlop Wall & Floor Tile Adhesive is a high performance, ready-mixed adhesive from Dunlop Trade (ARDEX Australia) that takes the hassle out of fixing most tile types. Supplied in an easy-to-handle 8kg pail, it is specially formulated to bond ceramic, porcelain, mosaics, fully vitrified tiles and natural stone (excluding moisture sensitive stone), and its highly flexible formulation copes with the small movements that occur in everyday walls and floors.Where to use itSuitable for indoor walls and floors, and outdoor areas provided there is no standing water and sufficient fall for run-off. It bonds over an impressive range of surfaces: cement render and concrete, fibre-cement sheets, existing ceramic and vinyl tiles, Dunlop Undertile Waterproofing, prepared metal surfaces, oil-based painted surfaces, plasterboard and suitably prepared interior timber.How to useMake sure the substrate is clean, dry and free of dust or grease. Spread the adhesive with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles, then bed tiles in firmly with a twisting motion. Work in small sections so a skin does not form before tiling.Important notesDo not use over strip timber floors. Prime particleboard and plywood sheet floors with Dunlop Tile-All before tiling. For fully immersed or pool applications choose a cement-based Dunlop adhesive instead.Specifications Size 8kg pail Colour Grey Coverage 0.8m²/kg (6-8mm trowel); 0.5m²/kg (10-12mm trowel) Tile types Ceramic, porcelain, mosaics, fully vitrified, natural stone (non moisture sensitive) Substrates Concrete, render, FC sheet, existing tiles, vinyl, metal, plasterboard, prepared timber Format Premixed dispersion adhesive SafetyWork in a well-ventilated area, wear gloves and eye protection, and avoid prolonged skin contact. Wash tools and hands with water before the adhesive dries. Keep out of reach of children and consult the SDS before use.
$93.46
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Premixed Mastic Tile Adhesive is a high performance, ready-to-use wall tile adhesive from Dunlop Trade (ARDEX Australia). Supplied in a convenient 20kg pail, there is no mixing, no mess and no guesswork – just open the lid and start trowelling. Its superior non-slump formulation holds even large format wall tiles and dimensional stone such as marble and granite firmly in place while you work, and its high flexibility and tenacity make it a favourite with tilers who want dependable grab straight off the trowel.Where to use itDesigned for indoor walls only. It is ideal for bathrooms, kitchens, laundries and splashbacks, and its unique formulation allows use in wet areas. Fix ceramic wall tiles, granite and marble (excluding moisture sensitive stone) over cement render, plasterboard, fibre-cement sheet, suitably prepared painted surfaces and Dunlop Waterproofing Membrane (porous tiles only).How to useEnsure surfaces are clean, dry and sound. Spread the adhesive with a suitable notched trowel, working in manageable sections, then press tiles firmly into the ribs with a slight twisting action. Adjust tiles within about 45 minutes of laying (at 23°C and 50% humidity). The adhesive dries in approximately 24 hours depending on temperature, and the porosity of the surface and tiles, after which grouting can proceed.Important notesDo not use over waterproofing membranes with dense or glazed tiles – use porous tiles only, as the adhesive will not dry properly between two non-absorbent layers. Not suitable for floors or exterior applications.Specifications Size 20kg pail Colour White Coverage Approx. 8-10m² per 20kg Tile types Ceramic wall tiles, granite, marble (not moisture sensitive stone) Substrates Render, plasterboard, FC sheet, painted surfaces, Dunlop membrane (porous tiles) Classification D2TE dispersion adhesive SafetyUse in a well-ventilated area and wear protective gloves and eye protection. Avoid skin and eye contact, wash hands after use and keep out of reach of children. Refer to the safety data sheet before use.
$99.60
Dunlop Express Wet Area Waterproofing is a high performance, water-based acrylic polyurethane membrane built for speed. Its high-build consistency lets you brush on a thick, even film that reaches the required membrane thickness with ease, and when used with Dunlop Express Wet Area Tape you can start tiling just four hours later. This handy 1kg tub is ideal for small repairs, patching and touch-up work, and it is backed by a 10 year guarantee.Where to use itUse indoors or outdoors in wet areas: showers, bathrooms, laundries and balconies. It adheres to AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard on walls and floors.How to usePrime the clean, dry substrate, seal junctions and penetrations with Dunlop Express Wet Area Tape, then brush on the first coat of membrane. Once dry, apply a second coat at right angles to the first until the required thickness is achieved. Tiling can commence after 4 hours when the full Express system is used. Wash brushes in water immediately after use.Important notesWaterproofing has minimum application requirements under AS3740: after two coats the dry film must be 1mm thick on floors and 0.5mm on walls. Check local council specifications before you begin. The membrane is a Class III membrane to AS/NZS4858.Specifications Size 1kg tub Coverage Up to 0.84m² on walls or 0.42m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyVentilate the area, wear gloves and eye protection, and avoid skin contact. Keep away from children and consult the Safety Data Sheet before use.
$43.00
Dunlop Express Wet Area Waterproofing in the 20kg pail is the full-bathroom format of Dunlop's fast-track membrane. This high performance, water-based acrylic polyurethane formula offers superior workability and a high-build film that reaches the required thickness without endless coats. Combined with Dunlop Express Wet Area Tape, the system lets tiling commence in as little as four hours, and it carries a 10 year guarantee.Where to use itMade for indoor and outdoor wet areas: showers, bathrooms, laundries and balconies. Apply it over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard, on walls and floors.How to usePrime the substrate with the appropriate Dunlop primer, seal all floor/wall junctions, corners and penetrations with Dunlop Express Wet Area Tape, then brush the membrane on generously. When the first coat is dry, brush on a second coat at right angles to the first to build the required film thickness. Tiling can begin after 4 hours when the complete Express system is used. Tools clean up in water while wet.Important notesAS3740 requires a minimum dry film thickness after two coats of 1mm on floors and 0.5mm on walls; confirm requirements with your local council. Certified as a Class III membrane to AS/NZS4858 and conforming to AS3740-2010 Wet Area Membranes.Specifications Size 20kg pail Coverage Up to 17m² on walls or 8.5m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyWork with good ventilation, wear gloves and safety glasses, and avoid contact with skin and eyes. Store sealed, away from children, and read the Safety Data Sheet first.
$313.95
Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.
$67.73
Dunlop Undertile Waterproofing is a hard-wearing, highly flexible liquid membrane that forms a seamless waterproof barrier beneath tiles. Brushed on straight from the pail, its ready-mixed blue formula makes it easy to see your coverage as you build the film, and once cured it protects the structure beneath showers, laundries and balconies from moisture damage for the long haul.Where to use itDesigned for indoor wet areas such as showers, bathrooms and laundries, as well as balconies. It bonds to AAC blocks, bricks, concrete, renders, screeds, fibre-cement sheet, marine plywood and wet area grade plasterboard on both walls and floors.How to usePrime the prepared surface with the appropriate Dunlop primer, then brush on the first coat of membrane, embedding Dunlop Reinforcing Mat into wall/floor junctions, corners, hobs and joints while it is wet. Once the first coat has dried, apply a second coat at right angles to the first to reach the required film thickness, then tile over it with a compatible Dunlop tile adhesive.Important notesAustralian Standard AS3740 sets minimum membrane thicknesses: after two coats, the dry film must be at least 1mm on floors and 0.5mm on walls. Check your local council requirements before starting. The membrane is certified to AS4858 and AS4654.Specifications Size 12.5kg pail Coverage Approx. 10m² on walls or 4.5m² on floors per pail Substrates AAC, brick, concrete, renders, screeds, fibre-cement, marine plywood, wet area plasterboard Colour Blue SafetyEnsure good ventilation, wear gloves and safety glasses, and avoid skin and eye contact. Keep the pail sealed and stored away from children. Read the Safety Data Sheet before application.
$142.94
Dunlop Multipurpose Primer in the 4 litre pack is the job-sized version of Dunlop's water-based bonding primer, made for whole-room and whole-house preparation work. It improves the bond between the substrate and Dunlop floor levellers, renders, tile adhesives and waterproofing membranes, turning dusty, porous surfaces into a reliable base. It suits new and old concrete, particleboard and compressed fibre-cement sheets alike.Where to use itUse indoors or outdoors, on walls and floors. It is at home on fibre-cement sheeting, concrete slabs, masonry and lightweight concrete blocks, particleboard, renders and screeds, before levelling, rendering, tiling or waterproofing with Dunlop systems.How to usePrepare the surface so it is clean, dry and free of dust, grease and loose material. Pour out the primer and spread an even coat with a brush or roller, working it into the surface. Let it dry clear before applying the next product in your system. Wash tools in water immediately after use.Important notesOn very porous substrates a second coat is required to achieve a continuous primed film. The white-on, clear-dry formula shows exactly where you have coated. Actual coverage depends on substrate porosity and site conditions.Specifications Size 4 litres Coverage Approx. 6m² per litre (up to approx. 24m² per pack) Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyWear gloves and eye protection, keep the work area ventilated, and avoid prolonged skin contact. Keep away from children and refer to the Safety Data Sheet before starting.
$60.26
Dunlop Multipurpose Primer is a water-based primer engineered to strengthen the bond between a substrate and the Dunlop product applied over it. It is the go-to preparation step for flooring work, priming ahead of floor levellers, renders, tile adhesives and waterproofing membranes, and it performs equally well on new or old concrete, particleboard and compressed fibre-cement sheeting.Where to use itApproved for indoor and outdoor use on both walls and floors. Typical substrates include fibre-cement sheets, concrete, masonry and lightweight concrete blocks, particleboard, renders and screeds. Prime before levelling a slab, rendering a wall, waterproofing a bathroom or laying tiles.How to useSweep or vacuum the surface so it is clean, sound and free of dust, oil and curing compounds. Apply an even coat by brush or roller and allow it to dry clear before applying your leveller, render, adhesive or membrane. Because it is water-based, brushes and rollers wash out in water straight after use.Important notesVery porous substrates will drink in the first coat, so a second coat is required to build a proper film. The primer applies white and dries clear, making coverage easy to track. Coverage figures are a guide only and vary with surface condition.Specifications Size 1 litre Coverage Approx. 6m² per litre Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyKeep off skin and out of eyes, wear gloves, and ensure good ventilation while working. Store sealed and away from children. Consult the Safety Data Sheet for full handling guidance.
$34.59
Dunlop Primer & Additive is a ready-to-use liquid primer that boosts the grip between your substrate and the Dunlop products that go on top of it. Whether you are about to level a floor, lay tiles or roll out a waterproofing membrane, a quick coat of this milky-white liquid seals porous surfaces and gives adhesives, levellers and membranes a far stronger key to bond to. It doubles as a grout additive, improving flexibility, adhesion, colour depth and resistance to abrasion and staining.Where to use itSuitable for both indoor and outdoor projects, on walls and floors. Use it over concrete, cement sheet, fibre-cement, plasterboard, sheeting and timber before applying Dunlop tile adhesives, floor preparation products or waterproofing membranes.How to useMake sure the surface is clean, dry and free of dust or contaminants. Apply undiluted before waterproofing, tiling and timber floor preparation; dilute it for priming wall board. On large floor areas a household broom works well to spread the primer and push it into the surface. Allow it to dry clear before continuing with your adhesive, leveller or membrane. Tools rinse out in water while the product is still wet.Important notesCoverage varies with the porosity of the substrate. The primer goes on white and dries clear, so you can easily see where you have already coated. Highly porous surfaces may need extra material.Specifications Size 1 litre bottle Coverage Approx. 4m² per litre undiluted; approx. 8m² per litre diluted Substrates Concrete, cement sheet, fibre-cement, plasterboard, timber Colour Applies white, dries clear SafetyWork in a ventilated area, avoid contact with skin and eyes, and keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.50
Dunlop Ardit Floor Leveller is a premium cement-based levelling compound built on the renowned Ardit Technology from ARDEX. It offers superior flow and workability, spreading easily across uneven concrete to create a smooth, even surface before new floor coverings go down. Floors are walkable in around 3 hours and ready for ceramic tiles in the same timeframe, keeping renovation and re-flooring jobs moving quickly.Where to use itUse indoors and outdoors under covered areas over sound concrete floors, ahead of ceramic tiles, carpet or vinyl. It is designed for concrete substrates only and must be protected by a floor covering rather than left exposed to the weather or used as a finished wear surface.How to useEnsure the slab is clean, sound and primed as required. Mix each 20kg bag with approximately 4.5L of clean water using a low-speed paddle mixer until smooth and lump free. Pour and spread with a trowel, letting the compound flow out and level itself. Apply from a thin skim up to 25mm in one pass, adding 2-5mm aggregate for deeper fills.Important notesNot suitable for driveways or areas subject to vehicular traffic. Vinyl and carpet can be laid after about 24 hours, while tiles can go down after roughly 3 hours. Refer to the technical datasheet for priming guidance on porous slabs.Specifications Size 20kg bag Coverage Approx. 12m² at 1mm or 4m² at 3mm per bag Thickness 1-25mm per application Substrates Concrete Walk-on time 3 hours (tiles 3 hours; vinyl and carpet 24 hours) SafetyContains cement, which is alkaline when wet. Wear gloves, eye protection and a P2 dust mask while mixing, ensure good ventilation, avoid skin contact and rinse promptly if the mix touches skin or eyes. Store away from children.
$67.45
Dunlop Multipurpose Floor Leveller is a cement-based levelling compound from Dunlop Trade (ARDEX Australia) that mixes with water into a smooth, free-flowing material for evening out rough or uneven concrete floors. It flows into low spots and finds its own level, leaving a flat base that is ready for foot traffic in around 2 hours and ready for tiles in about 4 hours, making it a dependable first step before laying new floor coverings such as carpet, vinyl or ceramic tiles.Where to use itSuitable for indoor and outdoor use over sound concrete floors, including living areas, kitchens, laundries and covered patios. It can also be used to form ramps or for bulk filling. It is designed for concrete substrates only and must always be covered by a finished floor covering.How to usePrepare the slab so it is clean, sound and free of dust or contaminants, and prime porous surfaces. Slowly add the powder to clean water while mixing with a low-speed paddle mixer for 2-3 minutes until lump free. Pour onto the floor, spread with a trowel and allow it to self-smooth. Apply up to 25mm in one application, adding 2-5mm aggregate for beds thicker than about 10mm.Important notesNot suitable for driveways or areas with vehicle traffic, and it cannot be left exposed as a wear surface. Sand can be added to create a trowelable screed for ramping. Always follow the technical datasheet for priming and mixing details.Specifications Size 15kg bag Coverage Approx. 1.6kg/m² per mm (about 9m² at 1mm per bag) Thickness Up to 25mm per application Substrates Concrete Walk-on time 2 hours (tiles after 4 hours) SafetyCement-based powders are alkaline and can irritate skin, eyes and airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in a ventilated area, wash skin after use and keep out of reach of children.
$69.96
Selleys Grout Stain Whitener is a water-based treatment that restores tired, discoloured grout to a clean, even white. Rather than simply scrubbing the surface, it coats the grout line to mask stains from mould growth, ingrained dirt, spilt makeup or hair-dye, leaving tiled areas looking fresh and bright again. It can also be used to recolour grey or other coloured grout to white. The formula contains a built-in fungicide that creates a protective barrier, making it harder for mould spores to take hold and for new stains to penetrate the grout, helping to break the mould cycle and keep grout looking cleaner for longer. It is supplied in a 280g tube fitted with a foam applicator tip for neat, controlled application straight onto the grout line. Where to use it Indoor: Tiled walls and floors in bathrooms, kitchens and laundries. Suitable for use on cement-based grout between ceramic and porcelain tiles. This is an interior-use product and is not intended for outdoor application. How to use Clean the tiled area and grout thoroughly and allow it to dry completely. Wearing gloves, an apron and old clothing is recommended. Press the foam applicator firmly against the grout and apply even pressure to the tube while moving the applicator along the grout lines. Allow to dry for at least 30 minutes, then check by wiping over with a damp cloth. If not yet dry, allow more time (no more than 2 hours). Once dry, remove excess with a lint-free damp cloth or sponge, wiping diagonally across the grout line. Reapply anywhere too little product was applied or too much was wiped off. After use, rinse the sponge under a downward-tilted tap, blot dry, and replace the lid firmly until next use. Allow at least 5 hours before the treated area is exposed to water. Important notes Do not use on unglazed or porous tiles and stone. Not recommended for tiles with intricate patterns or grooves from which the product may be difficult to remove. Heavily stained or coloured grout may need two applications. For longer-lasting protection, avoid harsh, abrasive cleaning of treated grout lines. Uncured product cleans up with water; cured product can be softened with methylated spirits. Specifications Brand Selleys Size 280g tube Colour White Technology Water based Use Interior Suitable surface Grout Application Foam applicator tip Safety Keep out of reach of children. Avoid contact with eyes and prolonged contact with skin; wear gloves during use and wash hands after handling. Use in a well-ventilated area. If in eyes, rinse thoroughly with water; if irritation persists, seek medical advice. Refer to the manufacturer's Safety Data Sheet for full handling, storage and first-aid information.
$20.51
Tarzan's Grip Wood Glue is a fast, dependable PVA timber adhesive built for everyday woodworking and repairs around the home and workshop. This 250mL bottle delivers a strong, lasting bond on a wide range of timbers, making it a reliable choice for cabinetry, joinery, furniture assembly and general carpentry jobs. The water-based PVA formula spreads smoothly, penetrates porous timber and sets to a tough, near-invisible bond line. Its extended working time gives you room to align and clamp pieces accurately before the glue grabs, while easy water clean-up keeps the job tidy with no harsh solvents. What it bondsIdeal for softwoods, hardwoods, plywood and MDF, and well suited to bonding porous materials to one another. Where to use itIndoor / Interior: furniture making and repair, cabinet and drawer assembly, joinery, trim and moulding, hobby and craft woodwork.Outdoor: this is an interior-grade wood glue and is not intended for fully weather-exposed or submerged applications. How to use it Make sure both surfaces are clean, dry and free of dust, grease and old finish. Apply an even coat of glue to one or both mating surfaces. Bring the parts together, align, and clamp firmly. Wipe away any squeeze-out with a damp cloth before it dries. Leave clamped until set, then allow full cure before stressing the joint. Important notesFor interior use only. Not classified as hazardous or as a dangerous good. Keep the cap closed between uses and store upright. Best results on clean, well-fitted joints with adequate clamping pressure. Specifications Brand Tarzan's Grip Product Wood Glue (PVA) Size 250mL Form Liquid Colour Light yellow Base Water-based PVA Density 1.05 g/cm³ pH 3.5 - 4.5 Clean up Water (while wet) Suitable for Softwoods, hardwoods, plywood, MDF Use area Interior SafetyBased on available information this product is not classified as hazardous under Safe Work Australia GHS criteria, and is not classified as a Dangerous Good for transport. Avoid eye contact and repeated or prolonged skin contact, and avoid inhaling mist or vapour. Wash hands after use and keep away from food and drink. If in eyes, rinse immediately with water; if swallowed, rinse mouth, do not induce vomiting, and seek medical advice. Store in a cool, dry, well-ventilated place out of direct sunlight and away from heat or ignition sources. Keep out of reach of children. Refer to the manufacturer's current Safety Data Sheet for full handling guidance.
$33.75
Endeavour QuickDeck is a premium water-based decking oil from Prep Productions, built for people who want a protected deck without the long dry times and strong odour of traditional solvent oils. Its oil-modified acrylic resin defends exterior timber on three fronts: it blocks moisture penetration, resists fungal growth and shields the boards from UV damage. Because it is water based, it dries fast, has low odour and low VOC content, and tools wash out in water. The 10 litre pail is the bulk pack, suited to large decks and full exterior timber projects, and covers up to roughly 140 square metres per coat at the maximum spread rate.Formula overviewAn oil-modified acrylic formula in a water base: a blend of water-soluble polymer resins refined to combine the penetrating character of an oil with the quick, low-odour convenience of an acrylic. The liquid is lightly coloured and dries to a transparent matt finish that lets the timber grain show through.Where to use itOutdoor: decks, garden furniture, pergolas, fences, gates and other exterior timbers.Indoor: not intended for interior floors or furniture. This is an exterior decking finish.How to use Stir well before use, as the product may settle on standing. Prepare the surface first: new or weathered boards should be cleaned with Endeavour Timber Deck Cleaner and allowed to dry. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 14 square metres per litre depending on timber porosity. Wash tools in water immediately after use. Important notes The finish is transparent matt: it enhances the timber tone but will not give an opaque colour. Apply in dry weather and avoid application if rain is expected before the coating has dried. Check the label for temperature and weather guidance. Results depend on preparation: grey, weathered timber should be cleaned back to sound wood first. Specifications Size 10 litres Base Water-based oil-modified acrylic, low VOC Coats 2 Recoat time 24 hours Coverage Up to 14 m² per litre Finish Transparent matt Application Brush or lambswool applicator Clean up Water Made in Australia SafetyNot classified as hazardous and not flammable. At most it may cause mild, short-lived skin or eye irritation, so gloves and eye protection are still sensible for prolonged use. Use in a well-ventilated area. If swallowed, do not induce vomiting, rinse the mouth, drink water and contact the Poisons Information Centre on 13 11 26 if symptoms develop. May settle or separate on standing, so stir before use, and prevent large spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$229.50
Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 5.2kg pail is the trade size for lining whole rooms.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the pail, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the pail label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the pail label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 5.2kg pail Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyNot classified as hazardous and not a scheduled poison. The paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. If it gets in the eyes, irrigate with water for 15 minutes and seek medical attention; skin washes clean with warm soapy water. If swallowed, rinse the mouth, drink water, do not induce vomiting and seek medical advice. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$33.20
Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 1kg tub suits patch jobs and small lining work.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the tub, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the tub label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the tub label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 1kg tub Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyNot classified as hazardous and not a scheduled poison. The paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. If it gets in the eyes, irrigate with water for 15 minutes and seek medical attention; skin washes clean with warm soapy water. If swallowed, rinse the mouth, drink water, do not induce vomiting and seek medical advice. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$17.90
Endeavour QuickDeck is a premium water-based decking oil from Prep Productions, built for people who want a protected deck without the long dry times and strong odour of traditional solvent oils. Its oil-modified acrylic resin defends exterior timber on three fronts: it blocks moisture penetration, resists fungal growth and shields the boards from UV damage. Because it is water based, it dries fast, has low odour and low VOC content, and tools wash out in water. The 4 litre pack covers a typical family-sized deck with two coats.Formula overviewAn oil-modified acrylic formula in a water base: a blend of water-soluble polymer resins refined to combine the penetrating character of an oil with the quick, low-odour convenience of an acrylic. The liquid is lightly coloured and dries to a transparent matt finish that lets the timber grain show through.Where to use itOutdoor: decks, garden furniture, pergolas, fences, gates and other exterior timbers.Indoor: not intended for interior floors or furniture. This is an exterior decking finish.How to use Stir well before use, as the product may settle on standing. Prepare the surface first: new or weathered boards should be cleaned with Endeavour Timber Deck Cleaner and allowed to dry. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 14 square metres per litre depending on timber porosity. Wash tools in water immediately after use. Important notes The finish is transparent matt: it enhances the timber tone but will not give an opaque colour. Apply in dry weather and avoid application if rain is expected before the coating has dried. Check the label for temperature and weather guidance. Results depend on preparation: grey, weathered timber should be cleaned back to sound wood first. Specifications Size 4 litres Base Water-based oil-modified acrylic, low VOC Coats 2 Recoat time 24 hours Coverage Up to 14 m² per litre Finish Transparent matt Application Brush or lambswool applicator Clean up Water Made in Australia SafetyNot classified as hazardous and not flammable. At most it may cause mild, short-lived skin or eye irritation, so gloves and eye protection are still sensible for prolonged use. Use in a well-ventilated area. If swallowed, do not induce vomiting, rinse the mouth, drink water and contact the Poisons Information Centre on 13 11 26 if symptoms develop. May settle or separate on standing, so stir before use, and prevent large spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$89.95
Endeavour QuickDeck is a premium water-based decking oil from Prep Productions, built for people who want a protected deck without the long dry times and strong odour of traditional solvent oils. Its oil-modified acrylic resin defends exterior timber on three fronts: it blocks moisture penetration, resists fungal growth and shields the boards from UV damage. Because it is water based, it dries fast, has low odour and low VOC content, and tools wash out in water.Formula overviewAn oil-modified acrylic formula in a water base: a blend of water-soluble polymer resins refined to combine the penetrating character of an oil with the quick, low-odour convenience of an acrylic. The liquid is lightly coloured and dries to a transparent matt finish that lets the timber grain show through.Where to use itOutdoor: decks, garden furniture, pergolas, fences, gates and other exterior timbers.Indoor: not intended for interior floors or furniture. This is an exterior decking finish.How to use Stir well before use, as the product may settle on standing. Prepare the surface first: new or weathered boards should be cleaned with Endeavour Timber Deck Cleaner and allowed to dry. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 14 square metres per litre depending on timber porosity. Wash tools in water immediately after use. Important notes The finish is transparent matt: it enhances the timber tone but will not give an opaque colour. Apply in dry weather and avoid application if rain is expected before the coating has dried. Check the label for temperature and weather guidance. Results depend on preparation: grey, weathered timber should be cleaned back to sound wood first. Specifications Size 1 litre Base Water-based oil-modified acrylic, low VOC Coats 2 Recoat time 24 hours Coverage Up to 14 m² per litre Finish Transparent matt Application Brush or lambswool applicator Clean up Water Made in Australia SafetyNot classified as hazardous and not flammable. At most it may cause mild, short-lived skin or eye irritation, so gloves and eye protection are still sensible for prolonged use. Use in a well-ventilated area. If swallowed, do not induce vomiting, rinse the mouth, drink water and contact the Poisons Information Centre on 13 11 26 if symptoms develop. May settle or separate on standing, so stir before use, and prevent large spills entering drains or waterways. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.95
Endeavour Timber Deck Cleaner is the preparation step before oiling any deck, new or old. It is a triple-action, water-based cleaner from Prep Productions' Endeavour range that cleans away grime, grease, mould, algae and mildew, restores stained and dirty boards to sound timber, and rejuvenates grey, weathered decks so they brighten back towards their natural colour. On new boards it strips out natural tannins, helping your decking oil penetrate evenly and last longer. The 4 litre pack is sized for full decks and repeat seasonal cleans.Formula overviewA water-based solution whose two key actives work together: oxalic acid brightens the timber and lifts tannin staining, while benzalkonium chloride, a biocide, deals with mould, algae and mildew. The concentrate is a pale, clear liquid that dilutes in water for application.Where to use itOutdoor: all new and weathered exterior timber, with decks the headline use. Also suited to preparing other exterior timber surfaces before finishing.Indoor: not intended for interior surfaces. This is an exterior timber preparation product.How to use Dilute with water as directed on the pack label. Apply the diluted solution with a deck scrub, working it into the boards. Rinse thoroughly and allow the timber to dry before oiling. Follow the label for contact time and drying guidance. Coverage is 5 to 10 square metres per litre when diluted, depending on timber porosity and texture. Important notes This is a Schedule 6 poison. Store it tightly closed, away from children and pets. Wear gloves and protective clothing: the concentrate is harmful in contact with skin and if swallowed. Prevent runoff entering drains, garden beds or waterways, and rinse surrounding plants with water if splashed. May settle on standing; stir before use. Specifications Size 4 litres Base Water-based, oxalic acid and benzalkonium chloride actives Coverage 5 to 10 m² per litre diluted Application Deck scrub Clean up Water Made in Australia SafetySchedule 6 poison. Harmful if swallowed and harmful in contact with skin. Wear rubber or nitrile gloves and eye protection, avoid contact with skin, eyes and clothing, and do not eat, drink or smoke while using. If swallowed, do not induce vomiting, rinse the mouth and call the Poisons Information Centre on 13 11 26 or a doctor. For skin contact, wash with warm soapy water for 10 to 20 minutes and remove contaminated clothing; for eyes, flush with lukewarm water and seek advice if irritation persists. Not flammable. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$39.95
Endeavour Timber Deck Cleaner is the preparation step before oiling any deck, new or old. It is a triple-action, water-based cleaner from Prep Productions' Endeavour range that cleans away grime, grease, mould, algae and mildew, restores stained and dirty boards to sound timber, and rejuvenates grey, weathered decks so they brighten back towards their natural colour. On new boards it strips out natural tannins, helping your decking oil penetrate evenly and last longer.Formula overviewA water-based solution whose two key actives work together: oxalic acid brightens the timber and lifts tannin staining, while benzalkonium chloride, a biocide, deals with mould, algae and mildew. The concentrate is a pale, clear liquid that dilutes in water for application.Where to use itOutdoor: all new and weathered exterior timber, with decks the headline use. Also suited to preparing other exterior timber surfaces before finishing.Indoor: not intended for interior surfaces. This is an exterior timber preparation product.How to use Dilute with water as directed on the pack label. Apply the diluted solution with a deck scrub, working it into the boards. Rinse thoroughly and allow the timber to dry before oiling. Follow the label for contact time and drying guidance. Coverage is 5 to 10 square metres per litre when diluted, depending on timber porosity and texture. Important notes This is a Schedule 6 poison. Store it tightly closed, away from children and pets. Wear gloves and protective clothing: the concentrate is harmful in contact with skin and if swallowed. Prevent runoff entering drains, garden beds or waterways, and rinse surrounding plants with water if splashed. May settle on standing; stir before use. Specifications Size 1 litre Base Water-based, oxalic acid and benzalkonium chloride actives Coverage 5 to 10 m² per litre diluted Application Deck scrub Clean up Water Made in Australia SafetySchedule 6 poison. Harmful if swallowed and harmful in contact with skin. Wear rubber or nitrile gloves and eye protection, avoid contact with skin, eyes and clothing, and do not eat, drink or smoke while using. If swallowed, do not induce vomiting, rinse the mouth and call the Poisons Information Centre on 13 11 26 or a doctor. For skin contact, wash with warm soapy water for 10 to 20 minutes and remove contaminated clothing; for eyes, flush with lukewarm water and seek advice if irritation persists. Not flammable. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$13.95
Krud Kutter Original Cleaner and Degreaser 946ml (Ready to Use Trigger Spray) Krud Kutter Original is a water-based cleaner, degreaser and stain remover that handles tough soils across a wide range of surfaces from a single bottle. Packed in a 946ml trigger pack, it sprays on straight from the bottle for everyday messes and can be used at full strength on the most stubborn grease and grime. It is biodegradable, low in odour and free from bleach, ammonia and harsh solvents, which makes it a practical choice for kitchens, garages, workshops and outdoor areas alike. Formula overview The formula combines a water base with a gentle surfactant system, an alkaline builder and a chelating agent that together lift fats, oils, road film and ground-in dirt. Because it relies on water-based chemistry rather than petroleum solvents, it rinses away cleanly, leaves no oily residue and is safe on most washable indoor, automotive and marine surfaces. It is colour fast and fabric safe on most materials, though a spot test is always sensible before a full clean. Where to use it Indoors Kitchen benches, splashbacks, range hoods, oven exteriors and BBQ grills Tiles and grout, sinks, tubs and shower screens with soap scum build up Painted walls, skirting and doors (test first and dilute for light marks) Lifting food and drink stains, marker, crayon, scuff marks and grease spots Outdoors Concrete paths, driveways and garage floors with oil and grease staining Outdoor furniture, fences and rendered or masonry surfaces Tools, machinery and engine parts (use on a cold, dry engine) Removing tree sap, bird droppings, brake dust and general weather grime How to use Always test on a small, hidden area first to check surface compatibility. For everyday cleaning, spray directly onto the surface and let it sit briefly. Wipe away with a clean, damp cloth or sponge. For heavy grease, oil or dried paint, apply at full strength, leave for a few minutes, then agitate with a brush or pad before wiping with a wet rag. For lighter cleaning over larger areas, the concentrate can be diluted with water. Rinse food contact surfaces with clean water after cleaning. Important notes Do not use on varnished surfaces or on leather. The formula is alkaline, so avoid prolonged contact with bare aluminium and other sensitive metals, and rinse and dry after use. Always test painted, delicate or porous surfaces in an inconspicuous spot before a full clean. Do not mix with other cleaning chemicals. Keep out of reach of children and pets. Specifications Brand Krud Kutter Product Original Cleaner, Degreaser and Stain Remover Format Ready to use trigger spray (concentrate, dilutable) Size 946 ml Base Water-based, biodegradable Use Interior and exterior Suitable surfaces Sealed hard surfaces, tiles and grout, glass, most plastics, metal, concrete and masonry, automotive and marine surfaces Not suitable for Varnished surfaces and leather Safety Keep out of reach of children. Avoid contact with eyes. If product enters the eyes, rinse with plenty of water and seek medical advice if irritation continues. Wear gloves if you have sensitive skin, and wash hands after use. Use in a well ventilated area and avoid breathing in the spray mist. Store upright in the closed bottle, away from extreme heat. Refer to the manufacturer Safety Data Sheet for full handling, first aid and disposal guidance. Glues Australia ships Australia wide. If you are not sure whether Krud Kutter is right for your surface, contact our team and we will help you pick the right cleaner for the job.
$20.05
Glitz Borax is a versatile cleaner and laundry booster that tackles grime, helps remove stains, and deodorises around the home. This mineral based powder dissolves in warm water to lift dirt, cut through residues, and freshen hard surfaces and fabrics. Why you will love it Multi purpose performance for laundry, kitchen, and bathroom Helps remove tough stains and lingering odours Boosts detergent effectiveness in hard water Deodorises bins, drains, and pet areas Free from added fragrance and chlorine Where to use Laundry booster for everyday washing Tiles, grout, sinks, and benchtops Toilets and bathroom surfaces Bins, outdoor furniture, and patios General deodorising tasks How to use Laundry booster: Add 1 to 2 tablespoons to the wash with your usual detergent. For heavily soiled loads use up to 1/4 cup. Dissolve in warm water for best results. Multi surface cleaner: Dissolve 2 tablespoons in 1 litre of warm water. Wipe surfaces with a cloth or sponge. Rinse food contact areas with clean water after cleaning. Stain pre soak: Dissolve 2 tablespoons in 2 litres of warm water. Soak colourfast fabrics for up to 30 minutes. Rinse well before washing as normal. Always patch test first. Deodorising paste: Mix borax with a little water to form a paste. Apply to tiles or grout, lightly scrub, then rinse. Bin and drain freshen: Sprinkle 2 to 3 tablespoons in the bin base or dissolve in warm water and flush down the drain. Rinse thoroughly. Good to know Use on sealed hard surfaces only Check fabric care labels and test on a hidden area first Not suitable for wool, silk, leather, or aluminium What is in the pack Glitz Borax powder 1 kg resealable pack Specifications Product type Multi purpose cleaner and laundry booster Form Free flowing powder Size 1 kg Fragrance None added Safety and storage Read and follow the label before use Wear gloves for prolonged contact Avoid inhaling dust. Use in a well ventilated area Keep out of reach of children and pets Do not ingest. Do not use on skin or as a personal care product Store in a cool dry place with the pouch sealed Disposal Rinse empty packaging and dispose of it in accordance with local council guidelines. Frequently asked questions Can I use it in cold waterYes, but it dissolves more readily in warm water. Pre dissolve in a small amount of warm water when using cold cycles. Is it safe for septic systemsUse sparingly and flush well with plenty of water. Follow any appliance and system guidelines. Will it bleach coloured fabricsIt does not contain chlorine bleach. Always check colourfastness and test on a hidden area first.
$12.22 $9.45
Glitz Spray On Wipe Off is your quick daily cleaner for busy kitchens, bathrooms, and high touch areas. Just spray, wipe, and you are done. It cuts through everyday grease, food splatter, soap scum, and dust to leave surfaces fresh and streak free. Why you will love it Fast spray and wipe action for daily clean ups Lifts light grease, grime, and sticky residues Streak free finish on most hard household surfaces Fresh clean scent that does not linger Ready to use 750ml trigger bottle for easy coverage Ideal for Benchtops and splashbacks Stainless steel appliances and rangehood exteriors Cooktops when cool, microwaves, fridges, and pantry shelves Bathroom vanities, taps, tiles, and shower glass Tables, desks, cabinet doors, light switches, and door handles Not recommended for Unsealed or waxed surfaces Natural stone such as marble, limestone, or travertine Untreated wood, leather, or fabrics Plasma or non glass coated display screens How to use Turn nozzle to the ON position. Spray directly onto the surface from about 20 cm away. Wipe with a clean damp cloth or paper towel. For stuck on grime, leave for 30 to 60 seconds before wiping. Buff with a dry cloth for a clear finish. Return nozzle to OFF after use. Pro tips Always test on an inconspicuous spot first. For food preparation areas, wipe with a clean damp cloth after cleaning. Use a microfiber cloth for best streak control on glass and stainless steel. Product details Brand Glitz Product type Everyday spray cleaner Format Ready to use Fragrance Fresh clean Bottle size 750 ml Surface compatibility Most sealed hard surfaces including laminate, ceramic, porcelain, stainless steel, glass, and finished wood What is in the box 1 x Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml with trigger Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other chemicals. FAQs Can I use it on stone benchtopsUse only on sealed engineered stone. For natural stone like marble or limestone, use a stone specific cleaner. Does it leave residueIt is designed to wipe clean. For food areas, finish with a damp cloth to remove any remaining cleaner. Is it suitable for glassYes for quick touch ups. For crystal clear windows, follow with a dry microfiber buff. Good to know Great for daily resets after cooking and bath time Trigger head lets you choose between stream and spray patterns Pairs well with microfiber cloths and paper towels
$6.71 $5.27
Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml Glitz Spray On Wipe Off is your quick daily cleaner for busy kitchens, bathrooms, and high touch areas. Just spray, wipe, and you are done. It cuts through everyday grease, food splatter, soap scum, and dust to leave surfaces fresh and streak free. Why you will love it Fast spray and wipe action for daily clean ups Lifts light grease, grime, and sticky residues Streak free finish on most hard household surfaces Fresh clean scent that does not linger Ready to use 750ml trigger bottle for easy coverage Ideal for Benchtops and splashbacks Stainless steel appliances and rangehood exteriors Cooktops when cool, microwaves, fridges, and pantry shelves Bathroom vanities, taps, tiles, and shower glass Tables, desks, cabinet doors, light switches, and door handles Not recommended for Unsealed or waxed surfaces Natural stone such as marble, limestone, or travertine Untreated wood, leather, or fabrics Plasma or non glass coated display screens How to use Turn nozzle to the ON position. Spray directly onto the surface from about 20 cm away. Wipe with a clean damp cloth or paper towel. For stuck on grime, leave for 30 to 60 seconds before wiping. Buff with a dry cloth for a clear finish. Return nozzle to OFF after use. Pro tips Always test on an inconspicuous spot first. For food preparation areas, wipe with a clean damp cloth after cleaning. Use a microfiber cloth for best streak control on glass and stainless steel. Product details Brand Glitz Product type Everyday spray cleaner Format Ready to use Fragrance Fresh clean Bottle size 750 ml Surface compatibility Most sealed hard surfaces including laminate, ceramic, porcelain, stainless steel, glass, and finished wood What is in the box 1 x Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml with trigger Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other chemicals. FAQs Can I use it on stone benchtops Use only on sealed engineered stone. For natural stone like marble or limestone, use a stone specific cleaner. Does it leave residue It is designed to wipe clean. For food areas, finish with a damp cloth to remove any remaining cleaner. Is it suitable for glass Yes for quick touch ups. For crystal clear windows, follow with a dry microfiber buff. Good to know Great for daily resets after cooking and bath time Trigger head lets you choose between stream and spray patterns Pairs well with microfiber cloths and paper towels
$33.11 $26.17
Glitz Sugar Soap for Floors Heavy Duty Cleaner Power through ground-in dirt, grease, and everyday grime with Glitz Sugar Soap for Floors. This heavy duty formula lifts stubborn residues and leaves floors fresh, streak free, and ready for living. Ideal for high traffic areas in homes, workshops, and commercial spaces. Why you will love it Heavy duty clean that cuts through grease, scuff marks, and sticky spills Low foam for a streak free finish on most sealed floors Fast acting formula reduces scrubbing time Residue free so finishes and sealers look their best Fresh, low odour for comfortable indoor use Best for these surfaces Use on most sealed and washable floors, including: Ceramic and porcelain tiles Vinyl and hybrid floors Laminate and sealed timber Sealed concrete and epoxy coated floors Do not use on unsealed timber, unsealed cork, natural stone that is unsealed, or waxed finishes. Always test in a small inconspicuous area first. How to use Sweep or vacuum to remove dust and grit. Dilute in warm water: General cleaning: 1 capful per 5 L bucket Heavy duty cleaning: 2 to 3 capfuls per 5 L bucket Apply with a mop or sponge. Work in sections. For stubborn spots, apply a little solution directly, wait 2 to 3 minutes, then gently agitate. Rinse mop frequently in clean water. Allow floor to dry before walking. Pro tips Change the bucket water when it turns cloudy to avoid streaks. Use heavy duty dilution before repainting or resealing floors to remove grease and prep the surface. For gloss finishes, wring the mop well to prevent pooling. Product details Brand Glitz Product type Sugar soap floor cleaner Format Liquid concentrate Appearance Clear to light solution, low foam Suitable surfaces Most sealed hard floors Clean up Rinse tools and mops in clean water Storage Keep tightly closed in a cool, dry place Safety Wear gloves if you have sensitive skin. Avoid contact with eyes. If splashed, rinse with water. Keep out of reach of children and pets. FAQs Do I need to rinse after cleaning Rinsing is generally not required on sealed floors when diluted as directed. If using heavy duty strength, a light rinse with clean water can help achieve a streak free finish. Can I use it in a spray mop Yes. Pre dilute following the general cleaning ratio and avoid over wetting the floor. Good to know Compatible with most microfiber and cotton mops Great prep step before resealing or repainting floors Helps remove oily residues that make floors feel slippery
$5.27 $4.94
You have seen 192 out of 388 products
Water-washable products for easy tool and surface cleaning, ideal for indoor work, schools and workshops. Great for PVAs, some acrylics and select hybrids; wipe spills before they skin. Use filters to refine by chemistry, set speed and finish. Always check the product page and TDS/SDS for prep, cure and clean-up instructions.
