Boston Premium PTFE Plumbers Pink Thread Seal Tape is a trade-focused thread sealing tape for water pipe fittings, supplied here as a bulk pack of 10 rolls for plumbers who get through plenty of tape. Each roll is 12mm wide and 10m long, and the pink colouring makes it easy to tell apart from other tapes on the truck or in the toolbox.About the formulaThis is a PTFE (polytetrafluoroethylene) film tape that fills the gap in tapered pipe threads to help prevent leaks at threaded joints. It was developed in Australia for professional plumbers, and it is WaterMark approved to WMTS 014:2016 (licence WMK26374). The tape has a density of 0.8g/cm³ and handles a wide temperature range, from -190°C to +310°C, so it suits both hot and cold water lines.Where to use itIndoors: threaded fittings on domestic and commercial water lines, such as taps, valves, unions and connectors.Outdoors: threaded water connections on garden and irrigation lines and other exposed pipework.Suitable for the threaded joints of water pipe fittings. Pink tape is intended for water use, so choose a tape that is rated for gas on any gas fitting.How to use itMake sure the male thread is clean and dry, and free of old tape, oil and debris. Hold the end of the tape on the thread and wrap it around the thread in the direction the fitting will tighten, so the tape does not unwind when the joint is made up. Overlap each turn slightly, keep the tape pulled snug so it presses into the thread grooves, and leave the first thread clear. Tear off the tape, press the end down, then assemble the joint and tighten as normal.Important notesDo not over-tighten, as this can damage fittings. If a joint leaks after assembly, undo it, remove the old tape and rewrap with fresh tape rather than adding more on top. Follow your local plumbing regulations and the fitting manufacturer's instructions for the job.Specifications Brand Boston Product Premium PTFE Plumbers Pink Thread Seal Tape Pack 10 rolls, each 12mm x 10m Colour Pink Material PTFE Density 0.8g/cm³ Temperature range -190°C to +310°C Application Hand wrapped onto threads Standards WaterMark approved, WMTS 014:2016, WMK26374 Use Hot and cold water pipe threads SafetyUse with normal care and keep the work area tidy so loose tape offcuts do not end up in pipework. Keep out of reach of children and store the rolls in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$29.73
Bastion Bond Breaker Waterproofing Joint Band is a 100mm wide, 10m long rubber reinforcing band for the most critical parts of a wet area waterproofing system, such as wall to floor junctions. It acts as the bond breaker in a liquid membrane system, so the membrane can cope with movement between two different surfaces instead of tearing at the join.About the bandThe band is made from a specialised grade of rubber that gives a rupture resistant seal and allows for the movement expected between abutting surfaces. It wets easily into the coats of a liquid membrane, which helps reinforce the finished membrane by improving puncture resistance and tensile strength. Because the band itself does the bond breaking, it removes the need for a separate bond breaker sealant at the joint, and installation is quick and straightforward. When used as part of a bond breaker system, it supports the requirements of AS 3740 (Waterproofing of domestic wet areas).Where to use itIndoors: wall to floor junctions in bathrooms, showers and laundries, and other critical joints in a wet area waterproofing system.Outdoors: Bastion's technical documentation lists the band as a bond breaker option within its membrane systems, but check the band's technical data sheet and your membrane's requirements before using it on external areas.It is designed to be embedded into Bastion liquid waterproofing membranes. Check your membrane's data sheet to confirm compatibility with other brands.How to use itMeasure and cut the band to suit each wall to floor junction. Apply a first coat of membrane, extending about 150mm up the wall and onto the floor, then embed the band into the wet membrane. Make sure the edges of the band are fully wetted out and there are no air bubbles behind it. Where lengths of band meet, overlap them by at least 50mm. If prefabricated corners are not being used, cut and fold the bottom leg of the band at corners and make sure it is fully bonded with the membrane. Then complete the membrane coats as set out in the membrane's data sheet.Important notesAlways follow the technical data sheet for the specific Bastion membrane you are using, including coat numbers and drying times. Surfaces should be properly prepared before the first coat goes on. Waterproofing in wet areas should be installed to the relevant Australian Standards and local requirements. If you are unsure, use a licensed waterproofer.Specifications Brand Bastion Product Bond Breaker Waterproofing Joint Band Size 100mm wide x 10m roll Pack 1 roll Material Rubber band Application Embedded by hand into wet liquid waterproofing membrane Minimum overlap at joins 50mm Standard Used as a bond breaker system to meet AS 3740 Use Wall/floor junctions and other movement areas in wet area waterproofing SafetyAlways read it and follow the instructions for the membrane you use with the band. Wear suitable protection when handling and installing it with liquid membranes, and store the roll clean and dry. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Boston Silicone Self-Fusing Tape in black is a 3 metre roll of stretchy repair tape made for quick fixes on leaking pipes and hoses. It fuses to itself as you wrap it, so there is no glue involved. It forms a watertight and airtight wrap, which makes it a handy emergency item for the plumbing kit, the toolbox or the shed.About the formulaThis is a silicone tape with no adhesive coating. It bonds only to itself, which means it does not leave sticky residue and can be removed cleanly when the job is done. The tape stretches well beyond three times its length, and that stretch is what lets it pull tight around pipes, hoses and fittings. It is rated for a very wide temperature range, from -55°C to +260°C. The black colour hides dirt and grime and blends in with black fittings.Where to use itIndoors: temporary sealing of weeping pipes, hose joins and fittings around the laundry, bathroom, kitchen or workshop; adding a comfortable, slip-resistant grip to tool handles.Outdoors: emergency repairs on garden hoses and tubing, and general fast fixes around the home, garden or workshop.The tape is designed for wrapping around pipes, hoses, fittings and tool handles. It is a multipurpose repair tape, so it also suits many other small wrap-and-seal jobs.How to use itMake sure the area you are repairing is clean and free of dirt and grease. Peel back the end of the tape and begin wrapping straight over the leak. Stretch the tape as you wind it on and overlap each turn, extending past the damaged spot on both sides. Press the finished wrap firmly so the layers fuse into one continuous seal. To fit a tool grip, wrap the tape around the handle in the same way. Cut the tape to length with scissors or a knife.Important notesBoston positions this tape for emergency and quick repairs. If a pipe or hose is badly damaged, plan to replace the affected section. Because the tape fuses only to itself, it will not stick to a surface if simply laid flat, so always wrap it back over itself. Keep the unused roll in a cool, dry place out of direct sun. Please follow the instructions that come with the pack.Specifications Brand Boston Product Silicone Self-Fusing Tape Pack 1 roll, 3m length Colour Black Material Silicone Application Hand wrapped, fuses to itself (no adhesive) Stretch Over 300% Temperature range -55°C to +260°C Use Pipe and hose leak repair, tool grips SafetyAs a general precaution, keep the tape out of reach of small children. Do not rely on it as a permanent fix for pressurised or safety-critical plumbing. Refer to the Safety Data Sheet (SDS) for full details.
$22.56
Kinetic Sink Sealing Tape is a flexible, self-adhesive foam tape for the join between a sink and the benchtop, supplied here as a handy 4 roll assorted pack. It is used underneath the sink rim to help protect the benchtop and stop leaks working their way under the bench.About the productThis is a black foam tape rather than a wet-applied sealant, so there is no cartridge, caulking gun or mess involved. The flexible foam is designed to sit in the gap under the rim of the sink. The pack includes two different profiles, so you can pick the one that suits the rim of your sink or basin: two rolls of 8mm x 8mm x 2m and two rolls of 10mm x 4mm x 2m.Where to use itIndoors: under the rim of kitchen sinks, laundry tubs and bathroom basins that sit on a benchtop, as a barrier between the sink and the bench surface.Outdoors: not intended for outdoor use. Use it for under-sink installations only.Suitable for fitting under drop-in style sink and basin rims. Check that the tape profile suits your sink rim before fitting.How to use itClean and dry the underside of the sink rim so it is free of dust, grease and old sealant. Cut the tape to length, then peel off the backing and press it firmly into place around the rim, keeping it continuous with no gaps at the corners or joins. Lower the sink into position and secure it as directed by the sink manufacturer. Always follow any instructions printed on the pack as well.Important notesChoose the profile that fits the rim of your sink best, and cut a little extra length so the run is fully covered, as small sinks can still need more than one roll. Keep the product away from heat and store it in a cool, dry place. Cure times, temperature limits and chemical resistance have not been confirmed by the manufacturer, so test in an inconspicuous spot if you have any doubts about compatibility with your sink or bench material.Specifications Brand Kinetic Product Sink Sealing Tape, assorted sizes Pack 4 rolls: 2 x (8mm x 8mm x 2m) and 2 x (10mm x 4mm x 2m) Colour Black Material Flexible adhesive foam Application Hand applied, peel and stick Use Under-sink and basin rim sealing (indoor) SafetyStore in a cool, dry place and keep out of reach of children. Wash hands after handling if the adhesive surface has been touched. Refer to the Safety Data Sheet (SDS) for full details.
$13.89
Kinetic Heavy Duty Thread Seal Tape is a pink PTFE plumber's tape for sealing threaded pipe and fitting connections, supplied here as a handy pack of five 12mm x 10m rolls. It gives a clean, positive seal on screwed joints and helps stop leaks at plumbing and heating connections, with a wide working temperature range for hot and cold duty.About the formulaThis is a PTFE (polytetrafluoroethylene) film tape in a heavy duty grade, coloured pink for easy identification on the job. PTFE is naturally corrosion resistant, so the tape will not rust or degrade the way some paste-type sealants can. It is rated for a working temperature of -100°C to 250°C. The tape is not an adhesive: it works by filling the small gaps between mating threads as the joint is tightened.Where to use itPlumbing: threaded water pipe connections and screwed brass fittings, which is the primary application listed for this pack.Heating: threaded joints in heating pipework and similar screwed connections.Suitable pipe and fitting materials include plastic, brass, copper, aluminium, galvanised steel and iron.How to use itMake sure the threads are clean and free of oil, dust and old sealant. Wrap the tape onto the male thread in the same direction the thread turns, so the tape does not unwind when the fitting is tightened. Keep light tension on the tape so it moulds into the thread form. Use several overlapping wraps (typically about four for small threads, with more for larger sizes), then screw the fitting together and tighten as normal. Test the joint under pressure before putting the system into service.Important notesWrapping against the direction of the thread can cause the tape to bunch up and unwind. Do not over-wrap, as too much tape can make fittings hard to assemble or crack plastic female fittings. Check that the tape is approved for your specific application, such as potable water or gas, before use, as approval details for this exact pack are not confirmed here. Keep away from open flames and do not use beyond the stated temperature range.Specifications Brand Kinetic Product Heavy Duty Thread Seal Tape Pack 5 rolls Roll size 12mm wide x 10m long Thickness 0.1mm Colour Pink Material PTFE Working temperature -100°C to 250°C Corrosion resistant Yes Application Hand wrapped onto male threads Packaging Blister pack SafetyAs general precautions, keep out of reach of children, keep away from open flames, store in a cool, dry place and wash hands after handling. Always follow the manufacturer's instructions and local plumbing regulations. Refer to the Safety Data Sheet (SDS) for full details.
$21.61
Fix-A-Tap Uniseal High Density PTFE Thread Seal Tape is a grey thread seal tape for gas and water pipe connections, supplied as a single 12mm x 10m roll on a card. The metallic grey pigment helps it blend in with chrome and galvanised fittings, so it is a good choice when you don't want white tape showing at the joint.About the formulaThis is a high density PTFE tape designed to form a leak-proof seal on suitable metal threads. It carries both AGA approval for gas threads and WaterMark approval for water threads. The AGA temperature range is -10°C to +210°C and the rated working pressure is 2MPa.Where to use itIndoors: threaded joints on water and gas pipework, such as fittings, connectors and valves, where a discreet grey finish is preferred.Outdoors: the manufacturer does not give specific outdoor guidance, so check the fitting and installation requirements for your job.It is intended for suitable metal pipe threads on gas and water lines. Always confirm that the tape suits the fitting and the service you are sealing.How to use itMake sure the male thread is clean, dry and free of old tape, oil and debris. Start at the thread end and wrap the tape around the thread in the direction the fitting will be tightened, so it doesn't unravel as you screw the joint together. Keep the tape snug and press it into the thread form, then assemble the joint. Gas fitting must be carried out by a licensed gas fitter in line with local regulations.Important notesUse only within the AGA temperature range of -10°C to +210°C and the rated working pressure of 2MPa. This tape is for threaded metal connections and is not a substitute for a compression, flange or push-fit seal. If a joint still weeps after assembly, dismantle it, remove the old tape and rewrap with fresh tape rather than adding more on top.Specifications Brand Fix-A-Tap Product Uniseal High Density PTFE Thread Seal Tape Size 12mm wide x 10m long Pack 1 roll on card Colour Metallic grey Material PTFE Application Hand wrapped onto pipe threads Temperature range (AGA) -10°C to +210°C Rated working pressure 2MPa Approvals AGA and WaterMark Manufacturer model number 208637 Use Gas and water pipe threads SafetyAs general good practice, keep the tape away from heat and flame beyond its rated temperature range, avoid overheating PTFE, and keep it out of reach of children. Wash your hands after handling if working in a dusty or dirty environment. Always follow the manufacturer's instructions and local plumbing and gas regulations. Refer to the Safety Data Sheet (SDS) for full details.
$4.95
The Fix-It-Fast Roof Repair Kit for Metal Roofs & Gutters is a ready-to-go patch kit for stopping leaks in metal roofing and gutters, with everything needed for the repair packed together in one tube. It pairs a self-adhesive Smartform flashing patch with a brush-on Wet Shield compound, so a homeowner can seal a leak in roughly five minutes without specialist tools or a tradie callout.About the formulaThe kit is a three-part system: a 300mm x 300mm Smartform patch, a 125g tub of Fix-It-Fast Wet Shield and an application brush. Smartform is an ultra-thin, flexible flashing with an aluminium surface and a butyl backing, and it can stretch by up to 60% so it can follow corrugated and irregular metal profiles. Wet Shield is a resin-based, fibre-reinforced, solvent-based repair compound. It is brushed around the edges of the patch to help stop water tracking underneath and lifting it. It can be applied to wet or damp surfaces, bridges small cracks, dries to a flexible membrane that resists algae and fungal growth, and needs no primer on sound, non-porous surfaces.Where to use itIndoors: not intended for interior use.Outdoors: patching leaks, splits and failed joins in metal roof sheeting (including corrugated and Colorbond profiles), gutters and valleys, and sealing around damaged flashing. It suits both residential and commercial maintenance jobs.Designed mainly for metal roofing and gutters. For tiled roofs, Fix-It-Fast makes a separate Tile Roof kit with a reinforced Dakaflash patch.How to use itClear loose debris, dirt, moss and algae from the repair area so the surface is sound and clean. Position the self-adhesive Smartform patch over the leak and press it down firmly so it conforms to the roof profile. Then brush Wet Shield around all the edges of the patch, overlapping onto the surrounding roof, to seal the perimeter and protect it from uplift. Once the Wet Shield has fully cured, it can be painted with an outdoor water-based acrylic paint if you want the repair to blend in. Keep the tub closed when not in use and follow the instructions supplied in the pack.Important notesA patch repair cannot fix a roof that is structurally unsound or unstable, so secure loose sheets and fixings first. The kit is built for localised repairs; for larger areas, Fix-It-Fast also sells flashing in longer lengths and Wet Shield in larger tins. Cure and recoat times are not confirmed here, so check the pack instructions. Wet Shield is solvent-based, so apply it in a well-ventilated outdoor area and keep it away from ignition sources.Specifications Brand Fix-It-Fast Product Roof Repair Kit for Metal Roofs & Gutters Pack 1 kit (patch, Wet Shield tub, brush) Patch Smartform flashing, 300mm x 300mm Patch stretch Up to 60% Wet Shield 125g tub Wet Shield base Resin-based, fibre-reinforced, solvent-based Application Self-adhesive patch plus brush-applied Wet Shield Pack dimensions Approx. 72mm x 72mm x 320mm tube Use Outdoor, residential and commercial SafetyThe Wet Shield in this kit is classified as a flammable liquid (Category 3) that may cause drowsiness or dizziness and is harmful to aquatic life with long-lasting effects. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Avoid breathing the vapours and wear protective clothing and eye and face protection. Do not eat, drink or smoke while using it, and wash hands after use. Refer to the Safety Data Sheet (SDS) for full details.
$44.59
Crommelin Pond Sealer Clear is a water-based, clear waterproofing membrane for sealing above-ground ponds, bird baths and ornamental water features, supplied here in a 1L pail. It goes on as a seamless coating and dries to a clear, low-sheen finish, so the look of the concrete, render or brickwork underneath is kept. It is designed to stay watertight under permanently wet conditions on structures that don't move.About the formulaA ready-to-use, water-based membrane that is non-toxic and safe for fish and plants. The manufacturer's technical data sheet also lists it as suitable for collecting or storing drinking water. It is UV stable, dries quickly and has excellent adhesion to porous cement-based surfaces. Repairs are easy, and tools wash up with water. It dries clear and hard, so it is meant for solid structures without joins, internal corners or expected movement. Where there are existing holes or cracks, or movement is expected, Crommelin recommends its Pond Sealer Colours membrane instead.Where to use itIndoors: ornamental water features, indoor fountains and other solid, porous water-holding features that won't flex.Outdoors: new or renovated above-ground fish ponds, bird baths, and ornamental water features built from concrete, render, brick or block.Suitable surfaces include concrete, cement render, brickwork, concrete blocks and other cementitious substrates. It is not suitable for non-porous surfaces.How to use itSurfaces must be clean, sound and completely dry, and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Repair any loose or crumbly areas first with a suitable repair mortar. To check porosity, wet a small area. If it darkens, the surface is porous and can be sealed. If it doesn't, it is too dense to seal. Stir the sealer well before use and apply with a brush or roller. Apply when surface and air temperatures are between 10 and 35°C and humidity stays at or below 85%. First coat: mix equal parts sealer and water, then apply a thin, even coat. Allow about 15 minutes to dry. Second coat: apply un-thinned sealer over the surface and let it dry. Third coat: apply un-thinned sealer at right angles (90 degrees) to the first coat. Wash brushes and rollers in water before the sealer dries. Important notesRecoat after about 4 hours. Full cure takes about 7 days, and good airflow helps. Keep the coating away from moisture until it has fully cured, and protect it from damage before filling with water. Not suitable for use in chlorinated water. Do not apply it to non-porous surfaces. It is not intended for in-ground ponds or for structures with cracks or movement. Don't apply in extreme heat, cold or humidity. Coverage depends on how porous the surface is. As a guide, 1L produces about 2 to 4 square metres of finished coating.Specifications Brand Crommelin Product Pond Sealer Clear Pack 1L pail Colour Clear when dry, low-sheen finish Base Water-based membrane Application Brush or roller Recoat time About 4 hours Full cure About 7 days Coverage About 2 to 4 m² of finished coating per 1L, depending on surface porosity Application conditions 10 to 35°C, maximum 85% humidity Clean up Water, before the product dries Use Interior and exterior, fish ponds and ornamental water features SafetyStore in a cool, dry place. Follow normal good practice when handling: avoid contact with eyes and skin, wash hands after use, and keep out of reach of children. Crommelin supplies it on request. Refer to the Safety Data Sheet (SDS) for full details.
$30.82
The Deks Rapid Flash Self-Adhesive Repair Strip is a lead-free, black flashing strip made for quick, temporary fixes to leaking roofs and gutters, supplied as a single 140mm x 500mm strip. It is a handy item to keep on hand when you need to stop a leak from a cracked tile or a damaged gutter until a permanent repair can be done.About the formulaThe strip is made from a rubber-based polymer with an integrated aluminium mesh. It has a fully adhesive base, so it goes on without separate sealants or fixings. The black finish suits most roof colours and materials. Deks lists the strip as suitable for all roof and gutter profiles and for most roof and gutter materials. It is lead-free, and you can cut it to size with heavy-duty scissors.Where to use itIndoors: not intended for interior use.Outdoors: temporary repairs to leaking gutters, cracked roof tiles and other roof leaks on a range of roof profiles and materials.Suitable materials include metal roofing and gutters, tile roofs and fibreglass sheeting. Deks describes the strip as suiting most roof and gutter materials, so test a small area first on unusual or heavily weathered surfaces.How to use itClean the repair area and let it dry fully, removing dirt, dust, loose debris and flaking material. Measure the area to be covered and cut the strip to length with heavy-duty scissors. Remove the backing from the adhesive face, position the strip over the leak and press it down firmly, working it into the roof or gutter profile so the adhesive bonds across the whole contact area. Always follow any instructions that come with the pack.Important notesThis is designed as a quick, temporary repair, so plan a permanent fix when conditions allow. Surface preparation matters, because the adhesive needs a clean, dry surface to grip. Take care when working at height, and be careful with cut edges of the aluminium mesh.Specifications Brand Deks Product Rapid Flash Self-Adhesive Repair Strip Pack 1 strip Size 140mm wide x 500mm long Thickness 2.3mm Colour Black Material Rubber-based polymer with integrated aluminium mesh Application Hand applied, self-adhesive backing, cut to size with heavy-duty scissors Lead content Lead-free Listed certifications AS 1530.8.1 (as listed by Deks), AS/NZS 2904, ASTM D7238, ASTM G154, BAL 19, BBA Use Exterior roof and gutter repairs (temporary) SafetyWear gloves when cutting and handling the strip, and watch for sharp mesh edges. Store the strip flat or rolled in a cool, dry place out of direct sun until you need it. Refer to the Safety Data Sheet (SDS) for full details.
$24.22
Rust-Oleum LeakSeal Flexible Rubber Coating Spray in white is a ready-to-spray rubberised coating for sealing leaks and cracks around the home, supplied here as a single 340g aerosol can. It lays down a firm but flexible, watertight layer that helps keep out water, air and moisture, and it also protects the coated surface from rust. It suits quick repairs on gutters, roofing, flashing and ductwork without mixing, brushing or special tools.About the formulaA solvent-borne, hydrocarbon resin coating that sprays on and builds up to fill small gaps and cracks (the manufacturer lists gaps and cracks up to 6.35mm). It dries to a semi-smooth, firm finish that stays flexible and is designed not to sag or drip, so it holds its shape on sloped and vertical surfaces. Once cured it can be top-coated with latex or oil-based paints, which makes it easy to blend repairs into the surrounding colour scheme.Where to use itIndoors: sealing cracks and leaks in ductwork, pipework surrounds and other protected areas, with good ventilation while you spray.Outdoors: patching gutters, flashing, metal roofing, downpipes, masonry and concrete surfaces that need a flexible waterproof barrier.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Do a small test spray first if you are unsure about a surface.How to use it Prepare the surface by washing it with a detergent and water solution, rinsing well and letting it dry fully. Lightly sand glossy surfaces and wipe off the dust. Mask off nearby areas to protect against overspray. Spray outdoors or in a well-ventilated space, ideally when the temperature is between 10 and 32 degrees Celsius and humidity is below 65%. Avoid very windy or dusty conditions, and allow more drying time in cooler weather. Shake the can vigorously for about one minute once the mixing ball starts to rattle, and shake it often while you work. Do a test spray on cardboard to get a feel for the spray pattern, then hold the can 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a second heavier coat for full coverage. Moving the can closer builds a thicker film. Some foaming or bubbling at first is normal and settles as the coating dries. After use, turn the can upside down and press the nozzle until only clear propellant sprays out. If the valve clogs, remove the spray tip and rinse it in mineral turpentine. Never push an object into the valve opening. Clean wet or dry coating with mineral turpentine or xylene. Important notesNot recommended for rubber surfaces or for surfaces that sit in continuous water immersion. Under the manufacturer's data, touch dry is about 2 hours at 21 to 27 degrees Celsius and 50% humidity, further coats can go on after 15 to 30 minutes, and you should allow 24 hours for a full cure and before top-coating. Cooler or more humid conditions will slow drying. This is not a fire or high-heat resistant coating. Shelf life is listed as 5 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour White Base Solvent-borne, hydrocarbon resin Application Aerosol spray Gap and crack fill Up to 6.35mm Touch dry About 2 hours (21 to 27°C, 50% RH) Recoat 15 to 30 minutes Handle 2 to 3 hours Full cure / topcoat 24 hours Practical coverage About 0.37 to 0.46 m² per can at a thick 125 micron film, or about 0.74 to 0.93 m² per can at 62.5 microns (manufacturer figures allowing for 15% material loss) Paintable Yes, with latex or oil-based paints Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. Contents are under pressure, so do not pierce or burn the can, even when empty. Use only outdoors or in a well-ventilated area, and avoid breathing the spray, mist or vapour. Refer to the Safety Data Sheet (SDS) for full details.
$23.95
Rust-Oleum LeakSeal Flexible Rubber Coating Spray in Black is a ready-to-use aerosol sealer for stopping leaks and sealing cracks around the home, workshop and site, supplied here as a single 340g can. It sprays on as a rubberised coating that builds a flexible, water-tight barrier over a wide range of common building surfaces, which makes it a quick fix for hard-to-reach or awkward spots where a caulking gun is difficult to use.About the formulaA solvent-based, hydrocarbon resin rubber coating that sprays on as a high-build film. It dries to a firm, semi-smooth black finish that stays flexible and is formulated not to sag or drip. The cured coating helps block moisture and protects against rust and corrosion, and it can be top-coated with acrylic (latex) or oil-based paints once cured.Where to use itIndoors: ductwork, pipes, air conditioner drip pans, vents and other protected areas where a flexible waterproof seal is needed (use only with good ventilation).Outdoors: gutters, downpipes, roof sheeting, flashing, skylight surrounds, metal sheds and buildings, and concrete or masonry surfaces where cracks or small holes let water in.Suitable surfaces include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Always do a small test spray on an inconspicuous area first, particularly on plastics.How to use itPrepare the surface so it is clean, dry and free of loose material, dirt, grease and flaking paint. Do a test spray on a piece of cardboard first to get a feel for the spray pattern, then apply the coating over the leak or crack using even passes, following the directions on the can. Additional coats can be applied after 15 to 30 minutes if a heavier build is needed. Once cured, the surface can be top-coated with acrylic or oil-based paint. Use outdoors or in a well-ventilated area.Important notesThe coating is touch dry in about 2 hours, can be recoated with itself after 15 to 30 minutes, and can be top-coated after 24 hours (times based on roughly 21 to 27°C and 50% relative humidity, so allow longer in cool or humid conditions). It is not intended for surfaces under continuous water immersion. It is not rated as fire or high-heat resistant, and it is not a mould or mildew-resistant coating. Coverage depends on the film thickness applied: about 0.74 square metres per can at a thin film (62.5 microns) or about 0.37 square metres per can at a thicker film (125 microns), allowing for typical material loss. Shelf life is around 2 to 3 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour Black Finish Semi-smooth, firm, flexible Base Solvent-based, hydrocarbon resin Application Aerosol spray Touch dry About 2 hours Recoat (with itself) 15 to 30 minutes Top-coat with paint After 24 hours Full cure About 24 hours Coverage per can About 0.74 m² at 62.5 micron, or 0.37 m² at 125 micron Paintable Yes, acrylic (latex) or oil-based paints Use Interior and exterior SafetyUse only outdoors or in a well-ventilated area, keep away from heat, sparks, flame and other ignition sources, and wear protective gloves, protective clothing, and eye and face protection. Store the can away from heat and do not store above 49°C. Refer to the Safety Data Sheet (SDS) for full details.
$27.92
Rust-Oleum LeakSeal Clear is a rubberised spray-on sealant that stops leaks and seals cracks in one easy aerosol, supplied here as a single 312g can. It lays down a flexible, water-tight coating over gutters, roofing, flashings, ducting and more, and the clear finish lets the original surface show through. It suits homeowners and maintenance tradies who need a quick, no-fuss repair.About the formulaA solvent-based, rubberised coating built on a hydrocarbon resin, delivered by a flammable propellant. It sprays on as a firm but flexible film that fills small gaps, cracks and holes (the manufacturer rates it for gaps up to about 6mm) and forms a barrier against water, air and moisture. It dries to a semi-smooth finish that does not sag or drip, helps protect the surface from rust, and can be topcoated with latex or oil-based paint once cured.Where to use itIndoors: ductwork, vents, pipes and other surfaces that need a flexible moisture seal.Outdoors: gutters, downpipes, roof flashings, metal roofing, sheds, vents and cracked masonry or concrete.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Test a small hidden area first on any surface you are unsure about.How to use itRemove all dirt and debris from the repair area. The manufacturer's technical data also advises washing with detergent and water, rinsing and letting the surface dry thoroughly, removing loose paint or old coatings, and lightly sanding glossy surfaces. Mask off surrounding areas to protect them from overspray.Apply outdoors or in a well-ventilated space, ideally between 10 and 32°C with humidity below 65%. Avoid very windy or dusty conditions.Shake the can vigorously for one minute after the mixing ball starts to rattle, and shake often during use. Do a test spray on cardboard to get a feel for the pattern.Hold the can about 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a heavier second coat for full coverage. Moving closer to the surface builds a thicker film.Once the coating has fully cured, it can be painted with latex or oil-based paint if you want it to match the surroundings.Important notesDry to touch in about 30 minutes, with full cure in about 24 hours. Not recommended for rubber surfaces or for surfaces under continuous water immersion. It is not fire or high-heat resistant and is not rated as mould or mildew resistant. Coverage varies with surface porosity and how thick you apply it. Do not apply to hot surfaces.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 312g aerosol can Colour Clear Base Solvent-based, hydrocarbon resin Application Aerosol spray Dry to touch About 30 minutes Full cure About 24 hours Maximum gap or crack size Up to about 6mm Application temperature 10 to 32°C Paintable Yes, with latex or oil-based paint Flexibility Remains flexible Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. The can is pressurised: do not pierce or burn it, even when empty, and do not expose it to temperatures above 50°C. Use outdoors or with good cross-ventilation. Refer to the Safety Data Sheet (SDS) for full details.
$23.25
![Rust-Oleum LeakSeal Self-Fusing Silicone Tape 25.4mm x 3.04m [Clear] (2)](http://gluesaustralia.com.au/cdn/shop/files/rust-oleum-leakseal-self-fusing-silicone-tape-25-4mm-x-3-04m-clear-2.png?v=1792411058&width=645)
Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a no-adhesive repair tape for stopping leaks on pipes and hoses and for wrapping damaged wiring insulation, supplied here as a clear 25.4mm x 3.04m roll. It stretches and wraps around awkward shapes, then fuses to itself to form a tight, water-resistant seal that suits quick home fixes as well as automotive and workshop repairs.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. That is why it peels away cleanly later without leaving a sticky residue. The manufacturer rates it excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention, and good for flame, abrasion, tear and solvent resistance. It is also rated good to fair for acid and oil resistance. It meets UL 510 and is claimed to insulate up to 8,000 volts.Where to use itIndoors: weeping or leaking pipes and joints, hoses on appliances, and frayed or worn cable insulation (see the electrical safety note below).Outdoors: garden and irrigation hoses, exposed pipework, and vehicle or equipment hoses and fittings exposed to sun and weather.Suited to wrapping around pipes, hoses, fittings and cables made from common materials such as metal and rubber. As the tape fuses to itself rather than relying on adhesion, it conforms to irregular shapes well. Test a small area first on delicate surfaces.How to use itDry the area to be repaired first. Hold the end of the tape firmly on the problem spot, then stretch the tape under tension as you wrap it around the object. Overlap each layer by about 13mm and keep wrapping so the tape lies over itself and fuses. Cover the whole problem area, cut the tape when finished and press the end down firmly. To remove it, simply unwrap or cut it off.Important notesThe tape needs to be stretched while wrapping, with each turn overlapping the last, to fuse properly. Loose or single-layer wraps will not seal. Treat it as an effective repair or emergency fix, and replace damaged pipes, hoses or cables where a permanent solution is needed. The manufacturer lists continuous operating temperatures from -45°C to 200°C and intermittent exposure from -65°C to 260°C, so keep it away from conditions above these limits. Do not rely on it to repair mains-voltage wiring: isolate the power first and have electrical work carried out by a licensed electrician. Avoid contact with strong oxidising agents, strong acids and strong alkalis.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Size 25.4mm x 3.04m roll (1 roll) Colour Clear Material Self-fusing silicone rubber tape Application Hand wrapped under tension, no adhesive or tools Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (+/- 5) after 24 hours Electrical insulation Up to 8,000 volts (manufacturer claim) Standard Meets UL 510 Use Interior and exterior SafetyWash your hands thoroughly with soap and water before eating, drinking or smoking after handling. If it gets in the eyes, rinse with water and remove contact lenses if present and easy to do. If heated to decomposition, silicone can give off acrid smoke and irritating fumes, so avoid excess heat and ensure good ventilation. Store the roll in a cool, dry place away from strong oxidisers, acids and alkalis. Refer to the Safety Data Sheet (SDS) for full details.
$20.12
Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a stretch-and-wrap repair tape for stopping leaks on pipes and hoses and for insulating damaged electrical wires, supplied here as a single black 25.4mm x 3.04m roll. It has no adhesive layer. Instead, each wrap fuses to the layer beneath it, so it forms a tight, sealed sleeve around the repair and can be cut off later without leaving sticky residue behind.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. Rust-Oleum describes it as a moisture and chemical resistant barrier that also helps protect against corrosion. Its technical data sheet rates it Excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention. It rates solvent, abrasion and tear resistance as Good. Acid, oil and hydrocarbon resistance is rated Good to Fair. The tape has a minimum tensile strength of 700 psi, a minimum elongation of 300% and a Shore A hardness of 55 (plus or minus 5) once cured for 24 hours. It meets UL 510. Rust-Oleum states it insulates up to 8,000 volts.Where to use itIndoors: temporary or emergency repairs on leaking pipes, fittings and hoses, and insulating or protecting frayed electrical wires and cable joins.Outdoors: wrapping hoses, fittings and exposed connections that face moisture and sunlight, including automotive and general workshop repairs.Because it fuses to itself, it works best on pipes, hoses, cables and other tubular or irregular shapes that you can wrap fully around.How to use itDry the surface before you start. Press the end of the tape onto the problem area, hold it firmly, then stretch the tape with tension as you wrap it around the object. Overlap each layer by about 13mm (the manufacturer gives 1.2 to 1.4cm) and wrap the tape over itself so it fuses. Cover the whole problem area, cut the tape and press the end firmly into place. To remove, cut the tape carefully with scissors or a knife.Important notesThe tape fuses to itself, so wrap it all the way around the item with each layer overlapping the last. The 700 psi figure on the TDS is a tensile strength rating, so do not treat it as a working pressure rating for pipes. Keep pressurised, hot or critical repairs in line with the system's own requirements and replace them with a proper repair where needed. The TDS gives a continuous operating range of -45°C to 200°C and an intermittent range of -65°C to 260°C. Flame resistance is rated Good, so do not treat the tape as fireproof. For electrical repairs, make sure the circuit is isolated and have any permanent work done by a licensed electrician.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Model number 279241 Size 25.4mm wide x 3.04m long roll (single roll) Colour Black Base Self-fusing silicone rubber Application Hand applied, stretch and wrap Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (plus or minus 5), cured 24 hours Electrical insulation Up to 8,000 volts (manufacturer rating) Standard Meets UL 510 Use Interior and exterior SafetyIf it gets in your eyes, flush with plenty of water for at least 15 minutes, keep the eyelids open, remove contact lenses if easy to do and keep rinsing. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$22.71
Gardner Bender Black Self-Bonding Repair Tape is a silicone emergency repair tape for quick, tidy fixes around the home, workshop and vehicle, supplied as a 2.5cm x 3m roll. It has no sticky adhesive layer. Instead, you stretch it as you wrap and it fuses to itself, forming an airtight, watertight seal that suits hoses, pipes, cables and tool handles.About the formulaThe tape is made from silicone and relies on self-bonding rather than glue. It only fuses to itself, so it doesn't leave a tacky residue on the item you wrap. The manufacturer describes it as resistant to heat, friction and UV, and it is rated for temperatures up to 260°C. That makes it handy for jobs where ordinary tapes would soften or perish.Where to use itIndoors: temporary repairs to leaking water pipes, wrapping and protecting electrical cables and connectors, and rebuilding or gripping tool handles.Outdoors and in the vehicle: patching engine hoses and radiator pipes, wrapping exhausts, and emergency repairs on guttering.It is well suited to hoses, pipes, cables, connectors, guttering and similar round or irregular shapes that can be wrapped. Because it bonds to itself rather than to the surface, it works on a wide range of materials.How to use itWipe the area to be repaired so it is clean and dry. For a leak, ideally shut off the flow or pressure first. Start wrapping a short distance beyond each side of the damage. Stretch the tape firmly as you wrap, overlapping each turn by about half the width so the layers press together and fuse. Finish by wrapping the end back onto itself and pressing it down firmly.Important notesThe tape must be stretched while wrapping, otherwise it won't fuse properly. It bonds to itself only, so it is a repair tool and not an adhesive for sticking two different surfaces together. It is an emergency and temporary repair for many plumbing and automotive jobs. Replace damaged pipes, hoses or fittings properly as soon as practical, particularly for high-pressure, gas, fuel or mains-voltage applications. Check the tape's suitability yourself before using it as electrical insulation on live circuits, and always isolate power first. Keep it below the rated temperature of 260°C.Specifications Brand Gardner Bender Product Self-Bonding Repair Tape Size 2.5cm x 3m roll Colour Black Material Silicone Adhesive None, bonds to itself Moisture sealing Yes (waterproof and airtight when wrapped) Maximum temperature Up to 260°C Resistance Heat, friction and UV Application Hand wrapped SafetyAs a general precaution, keep the tape away from children, wear gloves when working around hot pipes or exhausts, and allow hot surfaces to cool before wrapping. Isolate electrical power before working on cables or connectors. Refer to the Safety Data Sheet (SDS) for full details.
$21.44
Sika MultiSeal BT is a self-adhesive butyl sealing tape with an aluminium top surface, supplied here as a 10 m x 100 mm roll in grey for sealing and repairing roofs, gutters, flashings and other building elements. The high tack butyl adhesive grips a wide range of building materials, indoors and outdoors, so you can seal a joint or patch a leak without mixing, gunning or waiting for anything to cure.About the formulaThe tape is built on a flexible butyl rubber compound with a reinforced aluminium film on top. The aluminium face gives the tape its UV resistance. The butyl layer underneath is self-adhesive and is protected by a release liner until you are ready to stick it down. Sika describes it as having good adhesion at low temperatures, very good weather and UV resistance, and very good heat stability with no flow or oil migration. The aluminium face can be overpainted with most conventional paint systems, but test the paint first to confirm compatibility.Where to use itIndoors: sealing and insulating ductwork for ventilation and air conditioning, dampening and insulation work, and sealing joints on modular buildings and office containers.Outdoors: repairing and sealing sheet metal roofs and flashings, facade elements, concrete roof tiles, metal and PVC gutters and downpipes, chimneys and skylights, and caravans and containers.Suitable materials include metal sheeting, glass, timber, PVC and concrete, along with most other common building materials. Check the compatibility of the butyl adhesive with the surface first, particularly on plastics and painted surfaces.How to use itSurfaces must be sound, clean and dry. Sika recommends cleaning and pre-treating the substrate with Sika Aktivator-205 applied with a clean towel. Cut the tape to length, peel back the release liner and press the tape firmly onto the surface, working along its full length so it makes good contact. Follow the current Sika product data sheet for application temperature limits, joint overlaps and any other installation details.Important notesThis tape is not for use on natural stone. It is not a replacement for an adhesive or mechanical fixing, so do not use it for permanent fixing or in load-bearing applications. On porous surfaces, water can travel in underneath the tape. Test paint compatibility before overpainting.Specifications Brand Sika Product MultiSeal BT High Tack Elastomeric Butyl Sealing Tape Size 10 m roll x 100 mm wide Colour Grey Base Butyl rubber compound Top surface Aluminium foil Bottom surface Self-adhesive butyl with release liner Thickness 1.0 mm including film Service temperature -30 °C to +80 °C Application Cut to length and press on by hand Shelf life 36 months from date of production Use Interior and exterior SafetyFollow the storage and handling advice on the pack and in the data sheet. Keep the roll in its original packaging until needed. Refer to the Safety Data Sheet (SDS) for full details.
$57.09
Protite Fibreglass Resin is a low styrene emission (LSE) polyester resin for repairing cracks, dents, holes and worn patches on boats, caravans, cars, trailers, gutters and more, supplied here in a 500g size. Mixed with catalyst hardener and used with fibreglass matting or cloth, it gives DIYers and tradies a strong, workable repair material with good adhesion and a consistent wet-out.About the formulaA polyester LSE resin designed for general repair work. Once catalysed it cures to a hard, sandable and paintable finish that resists shrinkage and UV exposure. The resin is a viscous liquid and contains styrene, so it has a strong aromatic odour while you work. It does not cure on its own: you need to add a catalyst hardener (sold separately). Protite also offers a repair kit that bundles the resin with catalyst, matting and application accessories.Where to use itIndoors: repairs to fibreglass, timber, metal and plastic items, models and workshop projects, provided you have good ventilation.Outdoors: caravans, boats, trailers, bikes and cars, plus downpipes, leaky gutters, metal roofs and rusted panels, as well as fibreglass surfboards, pools and tanks.Suitable materials include fibreglass, steel, iron, aluminium, timber, masonry, PVC and smooth polyester surfaces. Test an inconspicuous area first when working on other plastics.How to use itClean the damaged area and remove loose material, grease and dust. Sand the surface so the resin has a key to grip. Pour only the amount of resin you can use in one session into a clean mixing container, then stir in the catalyst hardener. The catalyst manufacturer's guide is 2.5 to 3ml per 100ml of resin on a cold day, or 1.5 to 2ml per 100ml on a hot day. Mix thoroughly with a flat stirring stick until the colour is even. Work the resin into the repair (with matting or cloth if needed) by dabbing or rolling it out slowly to avoid trapping air bubbles. Allow it to cure, then sand and paint as required. Weather, humidity, depth of resin and draughts all change the amount of catalyst you need.Important notesUncatalysed resin will not harden, and too little catalyst or a very thin application can leave the resin tacky or uncured. Too much catalyst makes it gel sooner than expected. The manufacturer indicates the mix starts to gel after about 30 minutes at 25°C, and heat or extra catalyst shortens this while cold or less catalyst lengthens it. Take care when using polyester resin over epoxy surfaces and check compatibility first. Cure times depend on temperature and the amount of catalyst used. Clean tools before the resin cures.Specifications Brand Protite Product Fibreglass Resin (LSE) Size 500g Model number PF-FR0500 Base Polyester resin, low styrene emission Catalyst Required, sold separately Application Hand applied after mixing with catalyst, dabbed or rolled out Finish Sandable and paintable Resistance UV and shrink resistant Use Interior and exterior SafetyUse outdoors or in a well-ventilated area. Wear suitable gloves, eye protection and protective clothing, and avoid breathing vapours. Keep away from heat, sparks and open flames. Store in a cool, dry, well-ventilated place out of direct sunlight and away from ignition sources and incompatible materials, with the lid closed and out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$26.18
Fix-It-Fast Repair Tape is an aluminium-faced butyl flashing tape for quick, dependable waterproofing and leak repairs, supplied here as a wide 150mm x 5m roll. It suits DIYers and roofing or building trades who want a simple, self-adhesive way to seal flashings, gutters and damaged roof areas without mixing, heating or special tools.About the tapeThe tape pairs an aluminium top layer with a self-adhesive butyl backing protected by a release liner. This construction is designed for waterproofing and vapour sealing, and it is formulated to bond to virtually all non-porous building materials. The aluminium face is UV resistant, and the product is promoted for its excellent age resistance. The 150mm width covers larger repair areas in fewer passes than the narrower rolls in the range.Where to use itIndoors: vapour sealing and general waterproofing tasks on non-porous building materials where the tape will not be exposed to the weather.Outdoors: flashing repairs, gutters, downpipes, cracked or damaged roofing, metal roof sheeting, sheds, skylights, caravans and boats.Suitable materials include metal (including Colorbond), PVC, polycarbonate, fibreglass, timber and smooth masonry, provided the surface is clean, dry and free of dust and oils.How to use itClean the surface thoroughly and make sure it is dry. Cut the tape to the length you need and peel away the release liner. Press the tape down firmly, working from the centre outwards to push out air pockets, then press the edges down so they are fully sealed. For best results, apply when the temperature is above 5°C.Important notesAdhesion is best on clean, dry, non-porous surfaces. If an area is wet, dry it as much as you can before applying the tape. Rough, dusty, oily or porous surfaces can reduce adhesion, so prepare them properly first. The manufacturer indicates the tape remains stable in service from about -40°C to 90°C. Check the repaired area from time to time to make sure the seal is holding.Specifications Brand Fix-It-Fast Product Repair Tape, Aluminium Reinforced Butyl Flashing Tape Size 150mm wide x 5m long (1 roll) Colour Aluminium (silver) Construction Aluminium top layer with self-adhesive butyl backing Application Hand applied, peel and stick Service temperature -40°C to 90°C (manufacturer FAQ) Best application temperature Above 5°C Use Interior and exterior SafetyKeep it away from young children, and wear gloves when handling the aluminium edges if you are cutting it. Store the roll in a cool, dry place out of direct sun. Refer to the Safety Data Sheet (SDS) for full details.
$44.47
![Fastfix Wet Shield One Coat Instant Waterproofing 2.5kg [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/fastfix-wet-shield-one-coat-instant-waterproofing-2-5kg-grey-2.jpg?v=1792410637&width=645)
Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$89.91
Crommelin Sprayable Exterior Grade Waterproofing is a rubberised, shake-and-spray waterproofing coating in a 400ml aerosol, made for outdoor areas that cop regular water and UV exposure. It is designed to seep into and seal leaks, cracks and small gaps, leaving a flexible, watertight film that suits quick repairs on roofs, gutters and similar exterior surfaces. This pack is the grey finish.About the formulaA rubberised coating delivered from a pressurised can, so there is no brush, roller or mixing involved. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), permanently flexible and fast drying. It also helps protect the coated surface from corrosion and stops moisture getting through. Once cured it can be overcoated with most water-based (acrylic) paints.Where to use itIndoors: not intended for interior use. This is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, hoses, air conditioner drip pans and ductwork.Suitable surfaces listed by the manufacturer include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particle board, PVC piping and fibreglass. The product has not been tested for use in potable water systems.How to use itSurfaces must be clean, sound and dry, and free of dust, grease, release agents, loose particles and other contaminants. Shake the can vigorously for one minute, and do a test spray on cardboard to get a feel for the spray pattern. Hold the can roughly 8 to 18cm from the surface and apply a thin first coat, which acts as a primer, then let it dry. Follow with a heavier coat, moving the nozzle a little closer to build a thicker film. For longer-lasting protection apply three to four coats, and for wider cracks and gaps keep adding coats until the cavity is filled. Apply to the positive side only (the side where water enters the substrate). Recoat once touch dry, which is about 20 to 30 minutes depending on thickness, weather and site conditions, and allow good airflow to help it cure.Important notesApply in temperatures of about 10 to 30 degrees C and avoid applying when humidity is high (the recommended maximum is 85% during application and cure). Avoid spraying in high wind or dusty conditions. Cold temperatures and poor airflow will lengthen cure times. It can be painted over after 24 hours. Full cure takes 48 hours, and the coating should not be exposed to water until then. Coverage depends on the shape and condition of the surface. Always do a small test area first.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 400ml aerosol can Colour Grey Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Recoat time About 20 to 30 minutes (touch dry) Paint over After 24 hours Full cure 48 hours Application temperature 10 to 30 degrees C Overcoating Most water-based (acrylic) paints Use Exterior SafetyKeep away from heat, sparks, flames and hot surfaces, do not spray onto a flame or ignition source, and do not pierce or burn the can, even when empty. Use in a well-ventilated area, avoid contact with skin, eyes and clothing, and wash hands before eating, drinking or smoking. Store out of direct sunlight and keep below 50 degrees C. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
Crommelin Exterior Grade Brushable Waterproofing Membrane is a tough, flexible synthetic rubber coating for external areas that stay wet, supplied here in a 15L pail for larger jobs. It is designed for permanent water contact, for non-exposed areas with pedestrian traffic, and for use beneath screeds and toppings. It is built to move with the structure rather than crack as the building shifts.About the formulaA ready-to-use, water-based, synthetic rubber membrane (styrene butadiene rubber) in grey. It stays permanently flexible, bridges existing cracks up to 1.5mm and bonds to a wide range of building substrates. It is low VOC and dries quickly. Once cured it can be overcoated with screeds, renders and water-based coatings, so it suits layered waterproofing systems.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin offers separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits other areas of permanent water contact and non-exposed areas under screeds and toppings.Suitable substrates listed by the manufacturer include concrete and brick, cement render, plywood sheeting, cement sheeting, lightweight aggregate block, trafficable screeds, aluminium and steel (suitably primed).How to use itSurfaces must be sound, clean and completely dry, with no dust, grease, curing compounds, release agents, loose particles or efflorescence. Test moisture content before coating, ideally with an electronic moisture meter. Concrete should be cured for at least 28 days, and screeds and renders for at least 7 days. Remove high points and fill blow-holes and honeycombing with a suitable repair mortar. If the substrate is damp, prime it with Crommelin Dampstop. Treat any rust and remove loose rust material before coating metal. Stir the membrane well, then apply with a Crommelin applicator brush or roller at a surface and air temperature between 10 and 35 degrees Celsius. Recoat once touch dry, which is about 2 hours. Apply the second coat at right angles to the first. Reinforce corners, gutter damage and pin holes with Crommelin reinforcing fabric or bandage. Fit a suitable protection board over the cured membrane before any backfilling.Important notesDo not apply in extreme temperature or humidity. Full cure is about 7 days at 25 degrees Celsius, and coverage varies with substrate porosity. This product is intended for non-exposed pedestrian traffic, so protect the membrane from mechanical damage. Crack bridging applies to existing cracks up to 1.5mm only. Check the current manufacturer data sheet for your specific application and overcoating requirements.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofing Membrane Pack 15L pail Colour Grey Base Water-based synthetic rubber (styrene butadiene rubber) Application Brush or roller Coverage About 1.5m² per litre, roughly 11m² of finished coating per 15L Recoat time About 2 hours Full cure About 7 days at 25°C Crack bridging Existing cracks to 1.5mm Application temperature 10°C to 35°C Use Exterior, permanent water contact, non-exposed trafficable areas, under screeds and toppings SafetyAvoid contact with skin and eyes, wear suitable gloves and eye protection, and ensure good ventilation when applying. Store in a cool, dry place with the lid sealed. Wash tools in water before the membrane cures. Refer to the Safety Data Sheet (SDS) for full details.
$336.74
Crommelin Shower Sealer & Waterproofer is a clear, water-based silicate treatment designed to stop leaking showers by waterproofing the grout from within, with no need to rip out tiles. It soaks deep into cementitious grout and reacts inside it to block the passage of moisture, making it a practical fix for old, porous grout in showers, bathrooms and balconies. This listing is for a single 500ml bottle.About the formulaA waterborne silicate treatment that penetrates grout to a depth of up to 20mm. Once in the grout it undergoes a chemical reaction that Crommelin says permanently blocks moisture, and it dries completely clear so your tiles and grout lines look the same afterwards. It is a ready-to-use, single coat treatment, so there is no mixing, and equipment cleans up with water.Where to use itIndoors: shower recesses, bathrooms, kitchens and laundries with cementitious grout that has started to leak or let moisture through.Outdoors: balconies and other external areas with cementitious grout or similar cementitious construction materials.Suitable substrates are cementitious grout and other cementitious construction materials. It is not suitable for epoxy grout.How to use itPreparation: make sure the area is cementitious and free of dirt, mould, mildew and other contaminants. Wash with a strong bleach solution and rinse well. Replace any loose or drummy tiles and repair damaged or cracked grout with cementitious grout. Seal metal inserts with silicone, and make sure wall-to-wall and wall-to-floor joints are sealed with silicone rather than grout. The surface must be dry, so leave the area to dry for at least 12 hours before applying.Application: shake the bottle well, then apply liberally to the grout joints only, using a thin brush or a Crommelin Sealer Applicator Wheel. Wipe any excess off the tile surface with a damp cloth before it dries. Leave to dry for 30 to 40 minutes, then water the area thoroughly and scrub off any remaining excess. The area can be used straight away.Conditions: apply only when surface and air temperatures are within 10°C to 35°C, and avoid application when humidity is high or likely to be during the initial cure (maximum recommended humidity is 85%).Clean up: wash brushes and tools with water before the product dries.Important notesFull cure takes 7 days. Not suitable for epoxy grout. The grout must be clean and dry, and contaminants such as mould or old sealers can stop the treatment from penetrating properly. Crommelin's data sheet gives coverage of roughly 200 to 300 lineal metres of 5mm grout from the 500ml bottle, so actual coverage depends on grout width, depth and porosity. For full preparation and application detail, follow the Crommelin instructions and technical data sheet.Specifications Brand Crommelin Product Shower Sealer & Waterproofer Pack 1 x 500ml bottle Manufacturer code 6001-500 Colour Clear (dries clear) Base Waterborne silicate treatment Application Thin brush or Crommelin Sealer Applicator Wheel, grout joints only Penetration Up to 20mm into grout Dry time before watering in 30 to 40 minutes Full cure 7 days Application temperature 10°C to 35°C Coverage Approx. 200 to 300 lineal metres of 5mm grout (per manufacturer TDS) Clean up Water, before the product dries Use Interior and exterior SafetyAs a general precaution, avoid contact with eyes and skin, keep out of reach of children, and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$61.24
![Crommelin Sprayable Exterior Grade Waterproofing 400ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/crommelin-sprayable-exterior-grade-waterproofing-400ml-white-2.jpg?v=1792410554&width=645)
Crommelin Sprayable Exterior Grade Waterproofing is a ready-to-spray rubberised coating for sealing leaks and cracks on outdoor surfaces, supplied here as a 400ml aerosol can in white. It is made for spots that cop regular rain and sun, and it dries to a flexible, watertight layer that can be painted over with most acrylic paints.About the formulaA rubberised waterproofing coating in a pressurised can, so there is no brush, roller or mixing involved. The spray works its way into small holes and cracks to stop water getting through, helps block moisture penetration, and gives metal surfaces a barrier against corrosion. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), fast drying and permanently flexible. The white finish suits light-coloured roofing and masonry.Where to use itIndoors: not intended for interior use, as this is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, and hoses, air conditioner drip pans and ductwork.Suitable materials include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particleboard, PVC piping and fibreglass.How to use itMake sure the surface is clean, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and any other contaminants. Crommelin recommends its Water Rinsable Degreaser for removing grease and oils. Shake the can well, then spray the area to be sealed following the directions on the can. Once the coating has dried it can be over-painted with most acrylic paints. Full application instructions are available on the Crommelin website.Important notesThis product has not been tested for use in potable water systems, so do not use it on drinking water tanks or pipework. It is an exterior grade coating and is not designed as an under-tile or interior wet area membrane. Check the can and the manufacturer's data sheet for drying and recoating times and for surface or ambient temperature limits before starting.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 1 x 400ml aerosol can Colour White Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Overcoating Can be painted over with most acrylic paints Use Exterior Pack dimensions Approx. 64 x 64 x 197 mm SafetyThe can may burst if heated. Use only in well-ventilated areas, avoid breathing the spray, and keep away from heat, sparks, flames and other ignition sources. Wear gloves and eye protection, and remove any contaminated clothing and splashes from skin straight away. Store in a cool, dry place out of direct sunlight, do not expose to temperatures above 50°C, and keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$57.40 $40.04
Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.
$20.74
Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black
$23.08
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$50.18
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. SafetyTips Uncured product may irritate eyes. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Refer to the Safety Data Sheet (SDS) for full details.Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$51.50
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530329_412e3d45-40a8-4eca-9ed6-191f389472d4.jpg?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_0ee281c8-0366-40a5-bb6c-b1a12d613ac2.png?v=1754716380&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1002_13c9931e-09ce-4d00-a35f-0df6977453aa.jpg?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_54ba8b96-b758-4a94-8ba2-6b524d94e6ea.png?v=1754716370&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1003_d0705a81-d0df-43a8-b8d2-cd06f5c78769.jpg?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_733528b0-7c24-46e0-889e-87698aafcb17.png?v=1754716354&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-storm-sealant-black-waterproof-any-material-wet-or-dry-sil-x-290ml-2.jpg?v=1792406323&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safetytips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Refer to the Safety Data Sheet (SDS) for full details.
$19.00
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$18.00
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$14.53
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safetytips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$13.00
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
![Parfix Roof Gutter Concrete Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697115751_115bf094-7ace-4242-bb30-259319ee7c44.png?v=1754712242&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a grey, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$10.27
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$11.49
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_ad8c4dd8-7138-4341-881e-1e58084dc0c8.png?v=1754716023&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_d1f88907-d8a6-4e7f-b887-a4ac4f2ab20a.png?v=1754716023&width=645)
Monarch Mini Roof & Gutter Silicone is a neutral cure silicone sealant that is ideal for repairing or installing gutters, roofs, downpipes, skylights and more. It can also be used to install metal sheets in the roofing industry and various other building services. With such versatility on offer it's no wonder this product's demand has soared so rapidly! What else would you want from your sealant? Well there are added features like its flexibility and resilience that make it perfect for all applications. You can count on Monarch Mini Roof & Gutter Silicone to stick around because of its long-lasting durability - don't wait until disaster strikes again when you could have had the protection you needed beforehand. FEATURES Premium quality 100% silicone Non-corrosive Neutral cure AS 4020 approved BENEFITS Quick exposure to light running water Suitable for use in all weather UV resistant Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$11.04
Monarch Mini Roof & Gutter Clear Silicone: The Compact Caulking Solution Product Overview Designed for roofing and outdoor applications, the Monarch Mini is perfect for a variety of materials like metal, brick, galvanized iron, tiles, and aluminium. Key Features & Benefits Quick exposure to light running water UV resistant for lasting outdoor use Neutral cure, making it versatile and safe for different materials Non-corrosive and AS 4020 approved Compatible with Monarch Mini Compact Caulking Gun Perfect For Great for small projects where a full-size cartridge is not needed. Ideal for: Repairing gutters Fixing roofs Mending downpipes Tight spaces that traditional cartridges can't reach Colors Available Available in black and translucent versions for versatility in your projects. How To Use Best when used with a Monarch Mini Compact Caulking Gun to reach tight spaces. Always follow the safety guidelines as provided on the product label.
$7.35
Gorilla Tape To-Go Handy 1" Roll Convenient for on-the-go repairs, Gorilla Tape To-Go's 1 inch width packs a powerful grip in a portable size. With double-thick adhesive, tough reinforced backing and rugged weather-resistant shell, it sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. This size is ideal size for backpacks, toolboxes, glove compartments for camping, boating and more. Use like any other tape Tear by hand or cut to size Apply carefully smoothing out air pockets or rolls That's it, enjoy the strength and durability of Gorilla Tape
$11.07
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Silver]](http://gluesaustralia.com.au/cdn/shop/files/052427607409N_5d23d9cf-9af4-4971-af36-316c7ce35662.jpg?v=1754712479&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$26.69
You have seen 93 out of 93 products
Sealants and repair compounds designed to stop water ingress around fixtures, roofs and pipework. Select mould‑resistant, UV‑stable or potable‑water options where indicated. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
