Gyprock Wet Area Acrylic Sealant is a white, paintable acrylic sealant made for bathrooms, laundries and other wet area builds, supplied here as a single 450g tube. It is designed to give plasterboard and wet area linings a long-lasting, flexible seal where they meet shower bases, baths and plumbing fittings, and it also works as a general purpose gap filler.About the formulaA ready-to-use acrylic sealant that stays flexible once cured, so it can move with the joint instead of cracking. It contains an antifungal agent to help resist mould and mildew, and it has moisture resistant properties for use in damp rooms. It can be painted over once fully cured. It is manufactured in Australia for CSR Gyprock.Where to use itIndoors: sealing the edge of Gyprock Aquachek wet area lining against pre-formed shower bases and baths, sealing around plumbing penetrations and fittings, and filling general gaps and junctions in bathrooms, laundries and other damp areas.It suits both residential and commercial construction. It is intended for non-fire-rated wet area systems.Suitable materials include Hebel, concrete, masonry, brickwork, plasterboard, fibre cement, metal, timber and plastic substrates (test plastics on a small area first).How to use itMake sure the joint or gap is clean, sound and free of dust, grease and loose material before you start. Cut the nozzle to suit the size of the joint, run a continuous bead and press it into the gap so it contacts both sides. Smooth the joint, and keep your tools clean while you work. Let the sealant cure fully before you paint over it. Unopened tubes should be kept in a cool, dry place away from direct sunlight and below 30°C. Opened tubes may skin over near the opening, so discard any lump or skin and the remaining sealant can still be used.Important notesThis sealant is not designed for constant water exposure or for stopping active leaks. Do not paint until it is fully cured. It is not an easy-sanding product. Shelf life is 1 year from the date of manufacture. The manufacturer does not publish set, cure or coverage figures for this tube, so allow plenty of time before showering or painting and check the label for current directions.Specifications Brand Gyprock (CSR) Product Wet Area Acrylic Sealant Pack 1 x 450g tube Colour White Base Acrylic Application Tube, used with a caulking gun Specific gravity Approximately 1.55 VOC content 17g/L (as specified by GBCA) Shelf life 1 year from date of manufacture Paintable Yes, once fully cured Use Wet area sealing and general purpose gap filling Origin Made in Australia SafetyIn a fire, use carbon dioxide, foam, dry chemical or water spray, and note that heated decomposition may release carbon dioxide and acrid smoke. Store unopened tubes in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$17.77
Bondall BondCrete is an Australian made bonding and sealing agent that has been a building and renovating staple since 1951, supplied here in a 1L pack. One product covers several jobs: a woodworking and craft adhesive straight from the container, a primer and sealer when diluted, and a bonding additive for cement, sand and render mixes.About the formulaA concentrated, high solids, water-based polymer product that contains a resin additive for strong bonding. It is white in the container and dries clear with no gloss. Because it is so concentrated, it can be diluted with water for most jobs, which stretches a single litre a long way. Bondall says there is seldom any need to hack, chip or acid etch most surfaces before bonding.Where to use itIndoors: tile bedding and fixing, bonding render or toppings to prepared surfaces, sealing and dustproofing concrete floors in covered areas, priming porous walls before water-based paint, and woodworking and general craft projects.Outdoors: Bondall directs that exterior sealing needs its separate paving and concrete sealer, and BondCrete is not intended to be exposed to water, moisture or dampness. Treat this product as an interior or covered-area product.Suitable materials include concrete, brick and other masonry, plaster, stone, tiles and timber, along with other porous surfaces.How to use itStart with a surface free of dirt, dust, oil, grease and loose or flaking material. Stir well before use. Dilution ratios from the manufacturer (BondCrete to water): Sealer coat: 1 part BondCrete to 4 parts water Bondcoat for bedding, render or topping: 1 part to 1 part water. Apply the bedding while the coat is still wet or tacky. Admix for cement, sand and render: 1 part BondCrete to 10 parts water, used in place of mixing water. As a guide, 1L makes enough admix for about 20kg of cement. Woodworking adhesive: use neat, applied to one surface only. Press the pieces together and clamp lightly. Allow a sealer coat to dry for about 24 hours before painting with a water-based or acrylic paint.Important notesUsed neat, it sets in about 30 minutes and reaches maximum strength after 24 hours. Cement mixes made with BondCrete still follow normal curing, with full cure at around 4 weeks. It is not suitable for bonding plastic, rubber, glass or other non-porous materials. It is not suitable for permanently wet areas. Do not seal a floor with it if you plan to use an oil-based paving paint or similar floor coating. Drying times vary with the application and temperature, so allow at least 24 hours between coats. Protect it from freezing and from extremes of temperature and direct sunlight.Specifications Brand Bondall Product BondCrete Bonding & Sealing Agent (Cement Additive) Pack 1L Colour White in the container, dries clear Base Water-based vinyl acetate polymer mix Application Neat from the container, diluted as a sealer or bondcoat, or mixed into cement as an admix Set time (neat) About 30 minutes Maximum strength (neat) About 24 hours Coverage (older manufacturer datasheet) About 3.5 m² per litre undiluted, up to about 35 m² per litre at 1:4 dilution Use Interior and covered areas Origin Made in Australia SafetySwallowing it may irritate the stomach and cause nausea and vomiting. Vapours or mists may irritate the nose, throat and airways. Skin contact may cause redness or itching. Use with good ventilation, and wear gloves and eye protection as a sensible precaution. Refer to the Safety Data Sheet (SDS) for full details.
$31.98
Soudal Genius Gun Gap Filling Expanding Foam is a one-handed, ready-to-use polyurethane foam for filling gaps, holes and joints while adding thermal and acoustic insulation, supplied here as a single 500ml can. The applicator trigger is built into the can, so there is no need to buy a separate foam gun, and the can can be put away part-used and picked up again on the next job.About the formulaA one-component, moisture-curing polyurethane foam with a stable, thixotropic body that stays where you put it. A built-in trigger and straw let you control the amount you dispense, and the resealable applicator keeps the can usable for up to 6 weeks after first use. Once cured it is light, sound-reducing and chemically inert, with minimal shrinkage and very little post-expansion. Manufacturer data lists a free-foamed density of about 25 kg/m³, sound insulation of 58 dB and thermal conductivity of 0.037 W/m.K. One 500ml can yields roughly 19 litres of free foam, or about 17 metres of joint fill. The foam is champagne in colour and is not UV resistant, so exposed foam needs a protective finish.Where to use itIndoors: filling gaps around door and window frames, sealing pipe and cable penetrations, closing holes and cavities in walls and ceilings, cutting down draughts and thermal bridges, and adding a sound-deadening layer.Outdoors: sealing gaps and openings in roof constructions and around frames and penetrations. Cover the cured foam with paint, plaster or sealant to protect it from UV light.Suitable materials include brick, concrete, masonry, timber, metals and most plastics, as well as most other common building materials. It does not bond to polyethylene (PE), polypropylene (PP) or PTFE. Run a quick adhesion test on unusual substrates first.How to use it Make sure surfaces are clean, dry and free of dust and grease, then lightly mist them with water to help the foam cure. Shake the can hard for at least 20 seconds, then open the cover and fold the tube out horizontally. Turn the can over and squeeze the trigger to dispense. Fill holes and cavities only about one third full, as the foam expands a lot as it cures. Shake the can again every so often while you work. For deep voids, build up in layers and moisten between each layer. When you finish, detach the bung, plug the nozzle with it, close the cap and store the can upright. Once fully cured, trim the foam with a sharp knife, then sand, paint, plaster or cover with sealant as needed. Important notesWipe off uncured foam straight away with Soudal Gun and Foam Cleaner or acetone, and test the cleaner on plastics, lacquer and paint first as they can be affected. Cured foam can only be removed mechanically or with a PU foam remover, and it must never be burned off. Use the product between roughly +5°C and +30°C. Skin forms in about 7 minutes and the foam can be cut after about 25 minutes (manufacturer figures, measured under standard test conditions, so real-world times vary with temperature, humidity and bead size). Cured foam is not UV resistant. Do not use it near electrical boxes or light fittings without checking the clearance guidance. Unopened cans keep for at least 12 months when stored upright in a cool, dry place at +5°C to +25°C.Specifications Brand Soudal Product Genius Gun Gap Filling Expanding Foam Manufacturer code 132272 Pack 1 x 500ml aerosol can Colour Champagne Base One-component polyurethane, moisture curing Application Built-in Genius Gun trigger applicator, one-handed Reusable Up to 6 weeks after first use Skin formation About 7 minutes Cutting time About 25 minutes Yield (500ml) About 19 L of free foam, about 17 m of joint fill Shrinkage after curing Under 3% Expansion after curing Under 1% Temperature resistance (cured) -40°C to +90°C, up to 120°C for a maximum of 1 hour Can size 65 x 65 x 315mm Use Interior and exterior (protect from UV) SafetyThis is a pressurised aerosol with flammable propellant and contains isocyanates. Keep it away from heat, sparks, flames and other ignition sources, do not smoke while using it, and never pierce or burn the can, even when empty. Wear gloves, safety glasses and protective clothing, and use only in well-ventilated areas. People already sensitised to isocyanates, or with asthma, eczema or skin problems, should avoid contact with the product. Refer to the Safety Data Sheet (SDS) for full details.
$16.20
Bostik Fill It Expanda Foam is a one-component, multipurpose polyurethane expanding foam for sealing, filling, bonding and insulating in a single step, supplied here in a 500ml aerosol can with a straw applicator. It expands to take up gaps and cavities of many sizes, then cures into an airtight, moisture-resistant seal that is designed not to shrink away from the surrounding surface.About the formulaA moisture-curing polyurethane foam that is ozone safe and has a mostly closed-cell structure, so it insulates against both heat and cold. Once cured it can be cut, sanded, plastered or painted to a neat finish. The included straw applicator lets you place foam into tight or awkward spots and apply it at any angle. The foam is not UV stable, so cured foam left exposed to sunlight should be painted.Where to use itIndoors: filling gaps and cavities around window and door frames, insulating around pipes, cutting down draughts, dust and noise, and adding a sound-absorbing layer or acoustic baffle.Outdoors: sealing openings in roof construction, filling larger holes and gaps in exterior walls, and helping to keep out insects and rodents (paint exposed cured foam).Suitable materials include concrete, brick, stone, plaster, timber and metal, as well as many plastics such as EPS, XPS, rigid PU foam and uPVC. It is not suitable for polyethylene (PE), polypropylene (PP), polycarbonate (PC), PMMA, PTFE, soft plastics, neoprene or bituminous surfaces.How to use itMake sure surfaces are clean, dry and free of dust, grease and loose material. Apply within the temperature range given on the can (+5°C to +35°C). Fit the straw applicator, shake the can well as directed on the label, and fill gaps only part-way, because the foam expands as it cures. Follow the label and Safety Data Sheet for cleaning up uncured foam. Once cured, trim any excess by cutting or sanding, then paint, plaster or finish as required.Important notesDo not use where the foam will sit under a permanent water load, or in cavities that are too dry to supply the moisture needed for curing. The foam is moisture-curing, so cure time varies with temperature, humidity and the surface. Typical values at 20°C and 60% relative humidity are a skin time of about 8 to 12 minutes and a cure of around 1 hour for a 30mm bead. Uncured foam can stick firmly to skin and clothing, so keep it off both while working.Specifications Brand Bostik Product Fill It Expanda Foam Multipurpose Polyurethane Expanding Foam Pack 500ml aerosol can with straw applicator Colour Off-white Base One-component, moisture-curing polyurethane foam Application Aerosol can with straw applicator Application temperature +5°C to +35°C Skin time About 8 to 12 minutes at 20°C and 60% RH Cure rate About 1 hour for a 30mm bead at 20°C and 60% RH Temperature resistance (cured) -40°C to +90°C continuous Use Interior and exterior SafetyUse in a well-ventilated area, keep away from heat, sparks and open flames, and do not pierce or burn the can, even when empty. Wear gloves, eye protection and protective clothing, and avoid breathing vapour or aerosol. If skin or hair is contaminated, remove affected clothing and flush with running water. Store in a well-ventilated place away from heat and dispose of the can through an approved waste facility. Refer to the Safety Data Sheet (SDS) for full details.
$13.47
Parfix Foam Fill Triple Expanding Filler is a polyurethane foam in a 750g aerosol can, made for packing out large gaps, cracks and cavities in and around the home. It expands well beyond its sprayed volume to fill irregular voids, then cures to a durable, water resistant foam that bonds to most common building surfaces.About the formulaA one-part polyurethane foam based on an isocyanate (MDI) prepolymer, supplied in a pressurised can. Once cured it is a firm, shrink resistant foam that can be cut, sanded and painted. Cured foam is not UV resistant, so exposed outdoor areas should be painted or covered.Where to use itIndoors: gaps around pipes and cable penetrations, cracks and holes in walls, and cavities around frames and fittings.Outdoors: holes and gaps in brickwork and other building surfaces, protected from direct sunlight once cured.Suitable for most building surfaces, including timber, metal, brick, stone and other masonry. Test on a small hidden area first if you are unsure about a particular material.How to use itWear gloves and safety glasses and work in a well ventilated area. Make sure surfaces are clean and free of loose material, dust and grease. Follow the directions printed on the can for shaking, nozzle attachment and application. Because this foam expands strongly, fill the gap only partly and allow room for growth rather than over-filling. Once fully cured, trim any excess with a knife or saw, then sand or paint as required. Uncured foam is best wiped off straight away with a suitable cleaner as directed on the can. Cured foam must be cut or sanded off.Important notesNot UV resistant, so paint or coat any foam that will be exposed to sunlight. Take care not to over-fill, as expanding foam can distort thin frames, door jambs and window casings. Keep the can away from heat, flames and sources of ignition. Check the can label for temperature range, cure times and further directions, as these are not covered in the product data we hold.Specifications Brand Parfix Product Foam Fill Triple Expanding Filler Pack 750g aerosol can Colour Off white / yellow Base Polyurethane (isocyanate-based) Application Aerosol can Finishing Can be cut, sanded and painted Shrink resistant Yes UV resistant No Use Interior and exterior SafetyUse only in well ventilated areas, wear gloves and eye protection, avoid breathing vapour and wash hands after use. People with asthma or sensitivity to isocyanates should take particular care. Do not puncture or burn the can, and keep it away from heat and ignition sources. Store upright in a cool, secure place away from children and check periodically for leaks. Refer to the Safety Data Sheet (SDS) for full details.
$19.76
Turbo Concrete Bog is a fast-setting polyester repair filler for patching holes, chips and cracks in concrete, brick and masonry, supplied here in a 500ml container. It is often described as concrete in a can. It sets hard in minutes and dries to a dull grey that looks like real concrete, so small repairs can be finished on the same day.About the formulaThis is a two part system. The filler is a paste based on unsaturated polyester resin in styrene, and it is cured with a benzoyl peroxide hardener that is mixed in at the time of use. The paste has a no-slump body, so it stays put on vertical and overhead repairs without sagging. Turbo describes the cured repair as strong and water resistant, with no shrinkage. The cured filler can be painted with water based or oil based paints or epoxy floor coatings, usually within about an hour. It can also be left unpainted, or tinted with dry oxides to match coloured concrete.Where to use itIndoors: filling old dynabolt holes and repairing chips or cracks in garage and shed floors, steps and masonry walls.Outdoors: repairing driveways, paths, steps, brick and masonry walls.Suitable materials include concrete, brick and other masonry surfaces.How to use itClean the damaged area and about 5cm around it. The surface must be dry and free of dirt, dust, oil, wax, grease, paint and anything else that could stop the filler bonding. Mix the filler and hardener carefully in the proportions given on the pack. Weather and temperature affect how fast the mix cures, so work in manageable batches. Press the mixed filler firmly into the hole or crack and shape it before it hardens. Once cured it can be sanded, then painted or left as is.Important notesThe hardener is a separate component. Check what is in the pack when you receive it, because Turbo also sells its Red Hardener separately. Use the hardener amount recommended on the label, since changing it changes the set time. This is a repair filler, not an adhesive and not a concrete additive. It is not stainable. Always follow the mixing and application directions on the pack.Specifications Brand Turbo Product Concrete Bog Size 500ml Colour Light grey paste, dries to a dull grey Base Unsaturated polyester resin in styrene (two part, with benzoyl peroxide hardener) Application Hand applied with a putty knife or similar tool Dry to touch About 30 minutes Paintable Within about 1 hour Sandable Yes Stainable No Use Interior and exterior SafetyKeep it away from heat, sparks and flames. Work in a well-ventilated area and wear suitable gloves and eye protection. Store in a closed container in a dry, cool place below 30°C. Refer to the Safety Data Sheet (SDS) for full details.
$31.19
Tricleanium Adhesive Remover is a solvent-based cleaning agent for lifting stubborn sticky residue, supplied here in a 500ml bottle for both household and trade clean-ups. It is made for the leftovers that soap and water will not shift, including stickers, labels, gum, tar, crayon and tape or glue residue, so you can clean up without hard scraping.About the formulaThis is a fast-acting, solvent-based liquid that softens sticky build-up so it can be wiped, blotted or rinsed away. The manufacturer's safety data sheet describes it as a dark yellow liquid and lists ethanol and dipentene in its transport entry. It is a flammable liquid, so treat it with the same care you would any solvent product.Where to use itIndoors: removing label, sticker and tape residue from glass, metal, timber and tiled surfaces, and lifting gum, grease and sticky marks on hard surfaces around the home or workshop.Outdoors: cleaning adhesive, tar, carbon and other stubborn build-up from porous surfaces such as brick, concrete, terrazzo, marble and granite, and from vinyl siding.Suitable surfaces listed by the manufacturer include stone, concrete, brick, metals, vinyl siding, glass, fibreglass, timber, and fully cured varnished or oil-based painted surfaces. The manufacturer says it may damage some plastics and advises against using it on plastics, so keep it away from them.How to use itShake the bottle well. Start by putting a little product on a cloth and rubbing the mark. If that does not work, apply a light amount straight onto the surface. If you see no damage, you can use a natural fibre scrub brush to gently loosen the residue. Finish by blotting, rinsing or power washing the area clean. Always test on a small, hidden spot first. This matters most on auto finishes and vinyl.Important notesThe product may dull or damage some surfaces, so a test patch is essential. Repainted surfaces can dry with a visible gloss difference between the treated and untreated areas. Do not use on plastics. This product is not designed for adhesive bonding or sealing work, it is purely a remover for cleaning up residue.Specifications Brand Tricleanium Product Adhesive Remover Size 500ml Colour Dark yellow liquid Base Solvent-based Application Bottle, applied with a cloth or directly onto the surface Flash point Approx. 36°C Specific gravity Approx. 0.85 to 0.89 at 20°C Country of origin Australia Use Household, trade and maintenance, indoors and outdoors SafetyIt may also cause an allergic skin reaction, as well as drowsiness or dizziness. Keep away from heat, sparks and open flames, keep the container tightly closed, and use only outdoors or in a well-ventilated area. Avoid breathing mist or vapour, wear suitable gloves and eye protection, and wash exposed skin after handling. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$33.82
Goof Off Professional Strength Remover is a fast-acting solvent remover for sticky, gummy and stubborn mess, supplied here in a handy 177ml can for the garage, workshop or toolbox. It is built to break down stuck-on adhesive residue and marks that ordinary household cleaners struggle to shift, so you can rescue tools, hard surfaces and finished work instead of replacing them.About the formulaA ready-to-use, thin, clear liquid based on a strong solvent blend that includes acetone and xylene. It is poured or wiped on with a cloth rather than sprayed, which gives you control when you are working on small marks or tight spots. Expect a strong solvent smell, so good ventilation matters.Where to use itIndoors: tackling sticker and label residue, tape and glue marks, crayon, pen and marker, chewing gum, candle wax, lipstick and scuff marks on sturdy hard surfaces around the home.Outdoors and in the garage: cleaning up adhesive, tar, asphalt and similar grime from hand tools, and removing dried latex paint drips and caulk smears from suitable hard surfaces.Suitable materials include metal, glass, brick, wood, concrete, grout, fibreglass, hand tools and most automotive surfaces, as well as fully cured varnished or oil-painted surfaces. It is also promoted for marks on carpet and clothing, but test those first.How to use itWear eye protection and gloves and work in a well-ventilated area, away from any ignition source. Test on a hidden spot first, because every surface reacts differently. Apply a small amount to a clean cloth, then blot or lightly rub the mess until it lifts. Thick or layered residue may need a second pass. Wipe the area clean, let the vapours disperse, and reseal the can straight away.Important notesDo not use on plastics, worn vinyl flooring, some automotive paints or some carpets, as solvents can soften, dull or discolour them. Avoid large areas and spot test dyed fabrics and carpet before treating a visible mark. Keep out of reach of children. Always follow the directions on the can.Specifications Brand Goof Off Product Professional Strength Remover (Adhesive Remover) Size 177ml can Form Ready-to-use liquid Colour Clear Base Solvent-based Application Applied with a cloth, blot or rub lightly Use Indoor and outdoor hard surfaces Pack dimensions 55 x 32 x 135 mm SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use only with plenty of fresh air, wear safety glasses and chemical-resistant gloves, and stop work and move to fresh air if you feel dizzy or get a headache. If it contacts skin, remove contaminated clothing and rinse the skin with water. In case of fire use carbon dioxide, dry chemical, foam or water fog. Refer to the Safety Data Sheet (SDS) for full details.
$17.37
Duck Max Strength Nano Grab Mounting Circles are pre-cut, double-sided gel tape discs for quick, tool-free mounting, crafting and small repairs, supplied here as a 24 pack of clear 25mm circles. There is nothing to measure or trim: peel a circle off the backing, press it into place and you are done. The clear gel stays discreet on most finished jobs, and the circles can be washed and used again.About the formulaThese are clear, double-sided gel tape circles about 2mm thick. The adhesive is built from microscopic adhesive particles spread evenly through the gel, which is how the manufacturer achieves its long-lasting grip. The tape is designed to come away without leaving sticky residue, so it suits discreet repairs and finishes. It is intended for both permanent and temporary jobs.Where to use itIndoors: holding small decor pieces, lightweight organisers and office items in place, quick household fixes, and craft and DIY projects.Outdoors: the manufacturer lists these circles for outdoor as well as indoor use, so they can be used on sheltered outdoor tasks. Always test a single circle in the actual location first.Suitable materials listed by the manufacturer include brick, wood, cement, metal, glass, tile, ceramic and plastic. Results vary with the surface, so test plastics and any painted or delicate finish before committing.How to use it Make sure both surfaces are clean, dry and free of dust and grease. Peel a circle from its backing and press it firmly onto the first surface. Remove the second liner if there is one, then press the item or surface into position and hold it for a moment. To reuse, peel the circle away, rinse it in warm, soapy water, let it dry and apply it again. Important notesSome applications may not come off cleanly from painted surfaces, so test a small hidden spot before use. No load rating has been supplied for this product, so do not rely on it for heavy or safety-critical items or for anything that would cause harm if it fell. Results depend on the surface and conditions, so test it for your job first.Specifications Brand Duck Product Max Strength Nano Grab Mounting Circles Pack 24 circles Circle size 25mm x 25mm Thickness 2mm Colour Clear Type Double-sided gel tape (microsphere adhesive) Application Peel and press by hand, no cutting required Reusable Yes, wash with warm soapy water Use Indoor and outdoor SafetyKeep the small circles away from young children and pets, and do not eat or swallow them. Store in a cool, dry place in the original pack. Refer to the Safety Data Sheet (SDS) for full details.
$12.83
Scotch Multipurpose Gel Tape is a clear, double-sided mounting tape for hanging frames, mirrors, posters and wall decor without drilling, nails or screws, supplied here as a single 30mm x 1.5m roll. It is a removable option for DIYers and decorators who want a tidy, no-drill way to put things on the wall and take them down again later.About the productA transparent gel-style tape with adhesive on both sides, so it stays discreet once the item is mounted. It is sold for both light and heavier mounting jobs on hard, smooth surfaces and is designed to release when you want to take the item down, which makes it a good fit for rental-friendly decorating and creative projects. The tape is sold as a roll, so you can cut it to the length each job needs.Where to use itIndoors: hanging picture frames and mirrors, putting up lightweight posters and wall decor, and mounting smaller household items to hard, smooth surfaces.Craft and decorating: temporary display and feature-wall ideas where you want to avoid holes in the wall.Suitable surfaces include metal, tempered glass, tile, painted wood, smooth stone, brick, vinyl siding and acrylic. The surface should be hard and smooth.How to use itClean the surface so it is free of dust, grease and moisture, and let it dry fully. Cut the tape to length, press it firmly onto the back of the item, then press the item firmly against the mounting surface. Follow the directions printed on the pack for the weight rating and how long to wait before hanging heavier items. To remove, follow the pack instructions for releasing the tape, and clean off any leftover residue gently.Important notesNot recommended for delicate surfaces such as painted plasterboard or wallpaper, because removal may damage the finish. Always test on a small, hidden area first, particularly on painted or sensitive surfaces. Do not exceed the weight rating stated on the pack, and check the item is secure before leaving it unattended. Textured, dusty or porous surfaces will reduce grip.Specifications Brand Scotch Product Multipurpose Gel Tape (Scotch-Mount range) Size 30mm x 1.5m Pack Single roll Colour Clear Type Double-sided, removable gel mounting tape Application Hand applied, cut to length Use Hard, smooth surfaces (not for painted plasterboard or wallpaper) SafetyKeep out of reach of small children, who could swallow small pieces of tape. Avoid contact with eyes and do not eat the product. Store in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$13.59
Gorilla Ultimate Tape is the brand's toughest cloth tape, supplied here as a single black 48mm x 18.2m roll for hauling, strapping, patching, bundling and lifting jobs around the home, workshop and site. Gorilla rates it at five times the tensile strength of its original Gorilla Tape. It is designed for heavy loads rather than everyday taping.About the formulaThe tape combines a weather-resistant outer shell, a high tensile cloth layer and a double-thick, rubber-based adhesive. The thick adhesive layer bites into smooth, rough and uneven surfaces. The reinforced cloth is strong enough that you cut it with a utility knife or scissors instead of tearing it by hand. Gorilla states that a single loop of tape can hold more than 360kg. That figure comes from independent tensile testing in a controlled environment with specific preparation, so allow a generous safety margin on real jobs.Where to use itIndoors: bundling pipes, cables, timber and offcuts, patching and reinforcing packaging or equipment, and strapping loads in the workshop or garage.Outdoors: hauling and lifting loops, securing tarps and covers, and patching or holding items in damp or changeable weather, thanks to the moisture-resistant, weather-resistant shell.Suitable materials include wood, stone, stucco, brick, metal and vinyl. The manufacturer also states the adhesive sticks to most plastics, including polyethylene and polypropylene. It is not recommended on materials with a high oil or plasticiser content, such as EPDM rubber or PVC. Test a small area first on any surface you are unsure about.How to use itMake sure the surface is clean, dry and free of dust, oil and grease. Cut the tape to length with a utility knife or scissors. Apply it carefully and smooth out any air pockets or ridges as you go. For lifting, hauling or bundling loops, keep the tape free of creases and folds, because these can reduce its strength. Use extra wraps or additional tape for heavier loads. Apply at room temperature where possible. Store the roll in a cool, dry place out of direct sunlight.Important notesThis is not a hand-tear tape, so keep a knife or scissors handy. Take care when handling heavy loads, because serious injury can occur if a load or loop fails. Do not use it as a substitute for rated lifting or rigging equipment where safety depends on the load rating. Do not use it on PVC or EPDM rubber, as the adhesive is not suited to these. Gorilla's published guidance for the Ultimate tape is for application between about 4°C and 49°C, with continuous service up to about 65°C.Specifications Brand Gorilla Product Ultimate Tape Pack 1 roll Size 48mm wide x 18.2m long Colour Black Construction Weather-resistant shell, high tensile cloth, double-thick adhesive Adhesive Rubber-based Application Hand applied, cut with a utility knife or scissors Roll size (approx.) 130mm diameter Moisture resistant Yes Use Interior and exterior SafetyKeep it away from children and animals. Use caution when cutting with a knife and when handling heavy loads. Store it in a cool, dry place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$40.80
Gorilla Tape Tough & Wide is an extra-wide, heavy-duty duct tape for bigger repairs, patching and bundling jobs, supplied here as a single 73mm x 22.8m roll. The wider 73mm width covers more area in fewer strips, and it pairs a thick adhesive layer with a reinforced backing so it holds where ordinary duct tape tends to let go.About the formulaThe adhesive is a concentrated rubber-based formula applied in a heavier layer than standard duct tape, which helps it grip into rough textures and take up small surface irregularities. The reinforced, tightly woven backing adds strength and body, yet the tape can still be torn by hand without scissors. The outer shell is built to stand up to moisture, UV exposure and temperature swings.Where to use itIndoors: patching, sealing and bundling, holding items in place temporarily, and general household and workshop repairs.Outdoors: repairs and holds on exposed surfaces where sun, damp and changing temperatures would break down a lighter tape.Suitable surfaces include wood, stone, stucco, brick, metal and vinyl, including rough and uneven finishes. It may not hold well on materials with a high oil or plasticiser content, such as EPDM rubber, so test a small area first.How to use itMake sure the surface is clean, dry and free of dirt, grease and oil. Tear off the length you need by hand, or cut it with a knife or scissors. Press the tape onto the surface and rub it down firmly, smoothing out any pockets or wrinkles, to get the best grip.Important notesStore the roll in its original packaging in a cool, dry place, out of direct sunlight, to keep dirt and debris off the edges. Performance depends on the surface and conditions, so test first on critical or delicate surfaces. Not intended as a substitute for electrical insulation tape.Specifications Brand Gorilla Product Gorilla Tape Tough & Wide Size 73mm wide x 22.8m long Pack 1 roll Colour Black Adhesive Rubber-based, double-thick Backing Reinforced, tight weave, hand tearable Resistance Moisture and UV resistant Use Indoor and outdoor SafetyAvoid contact with strong acids, strong bases and strong oxidisers. Ensure adequate ventilation when working in enclosed spaces. Refer to the Safety Data Sheet (SDS) for full details.
$46.58
Ramset UltraFix Plus is a fast-setting, styrene-free polyester anchoring adhesive for fixing threaded studs and reinforcing bar into solid concrete and hollow masonry, supplied here as a single 300ml cartridge with two mixer nozzles. It is a medium duty chemical anchor that fits a standard caulking gun, so it suits small to mid-sized fixing jobs on site or around the home without specialist dispensing gear.About the formulaA two-part marine grade polyester resin. Part A is a polyester and filler paste and Part B is a peroxide catalyst, and the two are blended as the product passes through the mixer nozzle. The cartridge is styrene free for lower odour and is VOC compliant. The body is non-drip and resists slumping, which helps with horizontal and overhead holes. It is also designed to dispense easily in cool weather. The resin has been assessed for use in flooded holes under European Technical Assessment ETA 13/0681 (ETAG 001 Part 5, Option 7, in solid concrete).Where to use itIndoors: fixing brackets, hinges, plumbing and electrical fixtures and similar steel or timber fittings to solid concrete or hollow brick and block.Outdoors: setting gates, fence posts and fittings, signposts, guard rails and hand rails into concrete or masonry, including damp or wet holes.Suitable base materials include solid concrete, natural stone, hollow brick and hollow concrete block. It is intended for anchoring steel threaded rod, studs and reinforcing bar, and for fixing steel and timber fittings to those substrates. Hollow substrates are normally anchored with perforated sleeves (sold separately), so check Ramset installation data for your application.How to use itDrill the hole to the diameter and depth specified in Ramset installation data for your fixing, then clean it thoroughly with a brush and blow out the dust. Fit a mixer nozzle to the cartridge, load it into a standard caulking gun and dispense a little to waste until the mixed material is an even grey. Fill the hole from the bottom to avoid trapping air, then push the stud or bar in with a slight twist and leave it undisturbed. At 20°C the working time is about 6 minutes and the fixing can be loaded after about 50 minutes. Cure takes longer in cooler conditions. Always wear gloves and eye protection while mixing and installing.Important notesUse the supplied mixer nozzles only, as the adhesive relies on them to blend correctly. Do not use it in poorly ventilated or confined spaces. Cure and loading times depend on temperature, so allow longer when it is cold. For structural or load-critical fixings, follow Ramset technical data and engineering guidance for embedment, spacing and loading. Heavy duty or high-load applications may call for a higher-rated Ramset chemical anchor.Specifications Brand Ramset Product UltraFix Plus Chemical Anchoring Adhesive (model UFP300) Pack 1 x 300ml cartridge with 2 x mixer nozzles Colour Grey when mixed (Part A white, Part B black) Base Marine grade polyester, styrene free Application Cartridge, via standard caulking gun with mixer nozzle Working time About 6 minutes at 20°C Loading time About 50 minutes at 20°C Heat distortion temperature 80°C Approvals ETA 13/0681 (ETAG 001-5 Option 7, solid concrete, including flooded holes) Substrates Solid concrete, stone, hollow brick, hollow concrete block SafetyIt is not classified as a physical hazard and is non-flammable. Wear protective gloves, protective clothing and eye protection, avoid breathing vapours, wash thoroughly after handling and keep it out of drains and waterways. In case of eye contact, hold the eyes open and rinse with water for at least 15 minutes and seek medical help. For skin contact, remove contaminated clothing and wash the skin well, and seek advice if irritation or a rash develops. Refer to the Safety Data Sheet (SDS) for full details.
$41.97
Ramset ChemSet 101 Plus is a two-part, marine grade polyester anchoring adhesive for fixing threaded studs and starter bars into solid and hollow base materials, supplied here as a single 600ml cartridge with two mixing nozzles. It is made for trade and site work. Typical jobs include steel columns, machinery hold-downs, handrails and post-installed reinforcing bar.About the formulaThe resin is a marine grade polyester. Part A is a polyester polymer with inorganic filler, and Part B is a benzoyl peroxide catalyst. The two parts mix into a grey paste as they pass through the nozzle. The formula is styrene free, so it has a lower odour and low VOC once cured. It is non-drip and slump resistant, which suits overhead and vertical holes. It dispenses easily in cold weather. The resin is designed to reach full load capacity in dry, wet and flooded holes, as assessed to EAD 330499 Option 7. The cured adhesive is vibration resistant.Where to use itIndoors: machinery and equipment hold-downs, plate and frame fixings, handrails and balustrades, and starter bars or post-installed reinforcing bar.Outdoors: structural steel columns and beams, facade pins, gates, fencing posts and safety barriers, including in wet or flooded holes.Suitable base materials include solid concrete, brick and hollow concrete block, and it bonds steel threaded studs and reinforcing bar into them. Always check the Ramset load tables and the Specifiers Anchoring Resource Book for the design capacity of your application.How to use itFit the supplied mixing nozzle and load the cartridge into a compatible applicator, such as the Ramset ChemSet universal applicator. Dispense and discard the first portion until the colour is an even grey. Drill, clean and prepare the hole as set out in the Ramset installation instructions for your anchor type and size. Inject from the bottom of the hole, insert the stud or bar with a slight twist, and leave it undisturbed. Do not load the anchor until the cure time has passed. Fit a fresh nozzle if you stop work for longer than the working time.Important notesWorking time is about 6 minutes and loading time is about 50 minutes at 20°C. Cure times change with temperature, so check the Ramset data sheet for colder or warmer conditions. Installation is recommended with the base material and adhesive between 5°C and 40°C. The cartridge should not be below 5°C. The resin is not resistant to solvents such as acetone, benzene, xylene and styrene. Anchor design, hole preparation and loading should follow the manufacturer's technical documents, and critical structural fixings should be specified by a qualified engineer.Specifications Brand Ramset Product ChemSet 101 PLUS Polyester Anchoring Adhesive Model code C101S Pack 1 x 600ml cartridge with 2 x mixing nozzles Colour Part A white, Part B black, mixed grey Base Two-part polyester (styrene free) Application Cartridge, via a compatible applicator and mixing nozzle Working time About 6 minutes at 20°C Loading time About 50 minutes at 20°C Density 1.69 kg per litre at 20°C Heat distortion temperature 80°C (ISO 75) Service temperature -40°C to 80°C Installation temperature 5°C to 40°C (substrate and adhesive) Hardness Shore D 90 (ISO 7619) Compressive strength 70 MPa (ASTM 695) Tensile strength 12.2 MPa (ASTM D638) Flexural strength 28.3 MPa (ASTM D638) Assessment EAD 330499 Option 7 (flooded holes) Use Interior and exterior SafetyKeep it away from heat, sparks and open flames, and keep the container closed. Use it in a well-ventilated area and avoid breathing vapours. Wear protective gloves, protective clothing and eye or face protection. Wash thoroughly after handling and do not release it to the environment. Refer to the Safety Data Sheet (SDS) for full details.
$66.31
![Selleys Flexiseal FC Polyurethane Sealant & Adhesive 600ml Sausage [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-flexiseal-fc-polyurethane-sealant-adhesive-600ml-sausage-white-2.png?v=1792410682&width=645)
Selleys Flexiseal FC is a fast-curing polyurethane sealant and adhesive in white, supplied here as a 600ml sausage for sealing and bonding jobs around the building site or the house. It does two jobs in one product: it seals joints between common building materials and bonds them, and it stays flexible enough to cope with the movement those joints see through the seasons.About the formulaA single-component polyurethane with a non-slumping body, so it stays put in vertical joints instead of sagging. It is designed to grip common building surfaces without a primer, cures to a waterproof, flexible seal and can be painted once cured. Selleys rates it for joint movement of around plus or minus 25%.Where to use itIndoors: joints between wall and ceiling elements, around door and window frames, and acoustic rated walls, plus general bonding of building materials.Outdoors: weatherproofing joints between brickwork, masonry, concrete, timber or metal frames, sealing around roofing, retaining walls, external wall and cladding joints, and expansion joints.Suitable materials include concrete, brick, masonry, ceramic tile, metals, softwood and hardwood, plus some plastics (test other plastics and rubber first).How to use itMake sure the joint is clean, dry and free of dust, oil and other contaminants, and use a backing rod in deeper joints. Cut the end of the sausage, load it into a sausage-style applicator gun and extrude the sealant so it makes full contact with both sides of the joint, avoiding trapped air. Tool the surface smooth with a spatula before a skin forms. Once cured, it can be painted. For outdoor work, a suitable exterior paint will help the finish last longer.Important notesWill not adhere to polyethylene (PE), polypropylene (PP) or PTFE. Do not apply when the air or surface temperature is below 5°C. Not suitable for permanent water immersion or below water line use. Not intended for structural applications or general glazing. Avoid alcohol and solvent cleaners on the sealant while it cures, as they can interfere with the cure. Very damp substrates can cause bubbling in the sealant. It may affect the drying of oil or alkyd based paints, so test paint compatibility first. White sealant can yellow slightly with age and sun exposure. Store unopened sausages below 30°C in a cool, dry place out of direct sunlight, where they keep for around 12 months from manufacture. Opened sausages may skin over near the opening, so discard any lump or skin before using the rest.Specifications Brand Selleys Product Flexiseal FC Polyurethane Sealant & Adhesive Size 600ml sausage Colour White Base Polyurethane (single component) Application Sausage, via sausage gun Joint movement capability Plus or minus 25% Minimum application temperature 5°C Shelf life (unopened) About 12 months below 30°C Use Interior and exterior SafetyPolyurethane products can still irritate the skin, eyes and airways, so wear gloves and safety glasses, work with good ventilation and avoid prolonged skin contact. Store in a cool, dry, well-ventilated place away from heat, ignition sources and food, upright and tightly closed. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$32.06
Bondall Betta Tilecare Wet Area Waterproofer is a fast-curing, water-based liquid rubber membrane for sealing wet areas beneath tiles and renders, supplied here in a 10L pail for bigger bathroom, laundry and balcony jobs. It dries to a flexible, elastic film that acts as a water and vapour barrier, and it is designed to cope with permanently wet conditions, including ponding water once cured.About the formulaA water-based, one-part elastomeric membrane that is described by the manufacturer as non-toxic and non-flammable. It is classed as a Class III membrane under AS/NZS 4858 and, when used with the Betta detailing range, is designed to meet the Australian wet area requirements including AS 3740. The fast-curing formulation lets you tile or render over it quickly, and it is compatible with a range of tile adhesives, renders and toppings. No primer is needed on plasterboard or sound, dry concrete.Where to use itIndoors: bathroom and laundry floors and walls, shower recesses and other tiled wet areas, plus under screeds and toppings.Outdoors: balconies, decks, podiums and terrace floors, planters and retaining walls, and roofs that will be covered with screeds or toppings.Suitable substrates include concrete, screeds, renders, brick, plasterboard, fibre cement sheet and marine plywood. It sits under ceramic, porcelain, granite, marble and other stone tile finishes. Other surfaces, such as smooth, dense or damp ones, may need a Betta primer first, so check the technical data sheet for your substrate.How to use itMake sure the surface is sound, stable, clean and free of dust, oil, grease and loose material. Install the bond breaker and elastic joint band detailing first, as this is part of meeting AS 3740. Apply by brush, roller or spray unit in a minimum of two coats, changing direction between coats, to a total minimum coverage of 1.5 litres per square metre. This builds a dried film of roughly 1.2mm. Vertical or pitched areas can be done at around 1 litre per square metre. Take the membrane up walls at least 150mm in general wet areas and to 1.8m in shower recesses, finishing with a continuous, seamless film. Clean tools with water straight after use.Important notesTypical drying times at normal conditions (about 20°C, 50% humidity): tack free in about 45 minutes, recoat in about 1 hour, and ready to tile or topping over in about 4 hours. Retailer information quotes 6 hours before tiling, so allow the longer time in cool or humid weather and always follow the pack. Allow ample cure time before flood testing, as Bondall publishes more than one figure for this. Finish toppings must be water-based and solvent-free. Areas with rising damp or negative pressure should first be treated with Betta Damp Stop. Use on concrete slabs with hydrostatic or vapour pressure from below is outside the scope of the independent appraisal. Do not apply when rain is imminent. Always check the technical data sheet for your project.Specifications Brand Bondall (Betta Tilecare) Product Wet Area Waterproofer Pack 10L pail Base Water-based liquid rubber (elastomeric) Application Brush, roller or spray unit Coverage Minimum 1.5L per m2 over two coats (about 6.6 m2 per 10L pail) Dried film thickness Approx. 1.2mm Tack free About 45 minutes Recoat About 1 hour Tile or topping over About 4 to 6 hours (see notes) Standard AS/NZS 4858 Class III membrane Clean up Water Use Residential and commercial wet areas, interior and covered exterior SafetyEven so, wear gloves and eye protection, ensure good ventilation, and avoid contact with skin and eyes. Keep out of reach of children. Store in a sealed container in a cool place and protect from frost. Refer to the Safety Data Sheet (SDS) for full details.
$212.26
![Fastfix Wet Shield One Coat Instant Waterproofing 2.5kg [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/fastfix-wet-shield-one-coat-instant-waterproofing-2-5kg-grey-2.jpg?v=1792410637&width=645)
Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$89.91
Crommelin High UV Resistant Roof and Wall Waterproofing is a premium, liquid-applied elastomeric membrane for exposed, above-ground surfaces, supplied here in a 10L grey pack. It is made for places that cop full sun all year, such as rooftops, walls, parapets and balconies, and it forms a seamless, flexible waterproof coating that can also handle foot traffic.About the formulaThis is a high-performance elastomeric membrane that stays flexible once cured, so it can move with the surface beneath it. Because it goes on as a liquid, it forms one continuous film without laps or joins, which helps give leak-free performance. The manufacturer also lists it as an effective anti-carbonation coating for concrete. It resists dirt pick-up and algal growth, and it can be over-coated with acrylic paints if you want a particular finish. The manufacturer lists compliance with AS 4654.1 (waterproofing membrane systems for exterior use, above ground level, Part 1).Where to use itIndoors: not intended for interior use. It is made for exposed exterior situations.Outdoors: roofs and rooftops, exterior walls and facades, parapets, balconies, terraces, vertical surfaces and timber cladding or screening, including on trafficable areas that see regular foot traffic.Suitable surfaces listed by the manufacturer include concrete, concrete blocks, brickwork, masonry, renders, fibre cement sheeting, compressed cement sheets, timber (hardwood and pine) and suitably prepared metal such as steel and aluminium. Always test a small area first, especially on previously coated or challenging surfaces.How to use itPrepare the surface so it is clean, sound and free of dust, grease, loose paint and other contaminants. Metal needs suitable preparation before coating. Apply a test patch to confirm adhesion and appearance, then follow the manufacturer application instructions and technical data sheet for coat numbers, coverage rates and recoat times. If you plan to paint over the membrane, use an acrylic paint.Important notesThis product is designed for above-ground, UV-exposed use. Check the manufacturer technical data sheet before using it where water will pond or sit permanently, or where it will be covered by tiles. Cure and recoat times depend on temperature, humidity and film thickness, so follow the data sheet rather than guessing. Keep the membrane protected from damage until it has fully cured.Specifications Brand Crommelin Product High UV Resistant Roof and Wall Waterproofing Size 10L Colour Grey Type Elastomeric, liquid-applied waterproofing membrane Standard AS 4654.1 (exterior, above ground level) Over-coating Suitable for acrylic paints Traffic Suitable for pedestrian traffic Use Exterior, above ground, UV exposed SafetyStandard good practice still applies: wear gloves and eye protection, avoid contact with eyes and skin, and use in a well-ventilated area. Keep out of reach of children, store the container sealed in a cool, dry place, and do not let product enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$264.15
Crommelin Sprayable Exterior Grade Waterproofing is a rubberised, shake-and-spray waterproofing coating in a 400ml aerosol, made for outdoor areas that cop regular water and UV exposure. It is designed to seep into and seal leaks, cracks and small gaps, leaving a flexible, watertight film that suits quick repairs on roofs, gutters and similar exterior surfaces. This pack is the grey finish.About the formulaA rubberised coating delivered from a pressurised can, so there is no brush, roller or mixing involved. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), permanently flexible and fast drying. It also helps protect the coated surface from corrosion and stops moisture getting through. Once cured it can be overcoated with most water-based (acrylic) paints.Where to use itIndoors: not intended for interior use. This is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, hoses, air conditioner drip pans and ductwork.Suitable surfaces listed by the manufacturer include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particle board, PVC piping and fibreglass. The product has not been tested for use in potable water systems.How to use itSurfaces must be clean, sound and dry, and free of dust, grease, release agents, loose particles and other contaminants. Shake the can vigorously for one minute, and do a test spray on cardboard to get a feel for the spray pattern. Hold the can roughly 8 to 18cm from the surface and apply a thin first coat, which acts as a primer, then let it dry. Follow with a heavier coat, moving the nozzle a little closer to build a thicker film. For longer-lasting protection apply three to four coats, and for wider cracks and gaps keep adding coats until the cavity is filled. Apply to the positive side only (the side where water enters the substrate). Recoat once touch dry, which is about 20 to 30 minutes depending on thickness, weather and site conditions, and allow good airflow to help it cure.Important notesApply in temperatures of about 10 to 30 degrees C and avoid applying when humidity is high (the recommended maximum is 85% during application and cure). Avoid spraying in high wind or dusty conditions. Cold temperatures and poor airflow will lengthen cure times. It can be painted over after 24 hours. Full cure takes 48 hours, and the coating should not be exposed to water until then. Coverage depends on the shape and condition of the surface. Always do a small test area first.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 400ml aerosol can Colour Grey Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Recoat time About 20 to 30 minutes (touch dry) Paint over After 24 hours Full cure 48 hours Application temperature 10 to 30 degrees C Overcoating Most water-based (acrylic) paints Use Exterior SafetyKeep away from heat, sparks, flames and hot surfaces, do not spray onto a flame or ignition source, and do not pierce or burn the can, even when empty. Use in a well-ventilated area, avoid contact with skin, eyes and clothing, and wash hands before eating, drinking or smoking. Store out of direct sunlight and keep below 50 degrees C. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
Crommelin Exterior Grade Brushable Waterproofing Membrane is a tough, flexible synthetic rubber coating for external areas that stay wet, supplied here in a 15L pail for larger jobs. It is designed for permanent water contact, for non-exposed areas with pedestrian traffic, and for use beneath screeds and toppings. It is built to move with the structure rather than crack as the building shifts.About the formulaA ready-to-use, water-based, synthetic rubber membrane (styrene butadiene rubber) in grey. It stays permanently flexible, bridges existing cracks up to 1.5mm and bonds to a wide range of building substrates. It is low VOC and dries quickly. Once cured it can be overcoated with screeds, renders and water-based coatings, so it suits layered waterproofing systems.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin offers separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits other areas of permanent water contact and non-exposed areas under screeds and toppings.Suitable substrates listed by the manufacturer include concrete and brick, cement render, plywood sheeting, cement sheeting, lightweight aggregate block, trafficable screeds, aluminium and steel (suitably primed).How to use itSurfaces must be sound, clean and completely dry, with no dust, grease, curing compounds, release agents, loose particles or efflorescence. Test moisture content before coating, ideally with an electronic moisture meter. Concrete should be cured for at least 28 days, and screeds and renders for at least 7 days. Remove high points and fill blow-holes and honeycombing with a suitable repair mortar. If the substrate is damp, prime it with Crommelin Dampstop. Treat any rust and remove loose rust material before coating metal. Stir the membrane well, then apply with a Crommelin applicator brush or roller at a surface and air temperature between 10 and 35 degrees Celsius. Recoat once touch dry, which is about 2 hours. Apply the second coat at right angles to the first. Reinforce corners, gutter damage and pin holes with Crommelin reinforcing fabric or bandage. Fit a suitable protection board over the cured membrane before any backfilling.Important notesDo not apply in extreme temperature or humidity. Full cure is about 7 days at 25 degrees Celsius, and coverage varies with substrate porosity. This product is intended for non-exposed pedestrian traffic, so protect the membrane from mechanical damage. Crack bridging applies to existing cracks up to 1.5mm only. Check the current manufacturer data sheet for your specific application and overcoating requirements.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofing Membrane Pack 15L pail Colour Grey Base Water-based synthetic rubber (styrene butadiene rubber) Application Brush or roller Coverage About 1.5m² per litre, roughly 11m² of finished coating per 15L Recoat time About 2 hours Full cure About 7 days at 25°C Crack bridging Existing cracks to 1.5mm Application temperature 10°C to 35°C Use Exterior, permanent water contact, non-exposed trafficable areas, under screeds and toppings SafetyAvoid contact with skin and eyes, wear suitable gloves and eye protection, and ensure good ventilation when applying. Store in a cool, dry place with the lid sealed. Wash tools in water before the membrane cures. Refer to the Safety Data Sheet (SDS) for full details.
$336.74
Crommelin Blackseal Heavy Duty is a black, water-based bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 15L pail for larger jobs. It is a bitumen emulsion modified with a synthetic rubber co-polymer. It dries to a strong, flexible film that stays watertight in permanently wet conditions, which makes it a practical, economical choice where the finished membrane will stay out of sight and out of the sun.About the formulaA water-based bitumen emulsion with a synthetic rubber co-polymer for added flexibility and strength. It grips well to a wide range of building surfaces and is designed to help prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. The manufacturer describes it as non-toxic, non-flammable, fast drying and suitable for permanent immersion. It can be thinned with up to 50% water if you want a bitumen paint instead of a full-strength membrane.Where to use itIndoors: not intended for interior wet areas such as showers or bathrooms, because it cannot be tiled over or finished with a top coat.Outdoors: below-ground and non-exposed outdoor surfaces, including garden retaining walls, planter boxes, plant pots, timber posts and water tanks. It suits non-critical waterproofing jobs, not areas next to habitable spaces.Suitable surfaces include concrete, concrete blocks, brickwork and other masonry, renders, cementitious substrates, compressed cement and fibre cement sheeting, natural stone, plywood sheeting and timber. It also works on aluminium and steel that have been suitably prepared.How to use itStart with a clean, sound surface free of dust, grease, loose material and flaking coatings. Stir the pail well, then apply with a brush or roller. Two coats are recommended, and the 15L pail covers about 11.25 square metres at that rate. Let each coat dry before applying the next. Mix with water only if you want to thin it for use as a bitumen paint, and do not go past 50% dilution. Wash tools with water straight after use, before the product dries. Check the current Crommelin product information sheet for recoat times and full preparation advice before you start.Important notesDo not paint, tile over or over-coat this membrane, and do not use it on trafficable surfaces. It is not suitable where UV stability is required, so keep it covered or buried. For shower areas or UV-exposed roofs and walls, choose a purpose-made Crommelin membrane instead. Because it is for non-critical applications only, it is not a substitute for a compliant waterproofing system in habitable or wet areas. Cure times vary with temperature, humidity and airflow, so allow enough time before backfilling or exposing the membrane to heavy moisture.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Pack 15L pail Colour Black Base Water-based bitumen emulsion modified with synthetic rubber co-polymer Application Brush or roller Number of coats 2 Coverage About 11.25 square metres per 15L (two coats) Dilution Up to 50% water to make a bitumen paint Clean up Water, while wet Use Below ground and non-UV-exposed areas only SafetyUse it with good general ventilation. Normal site protection such as safety glasses and overalls is sensible, along with good hygiene. Store the pail sealed, away from extreme temperatures and freezing, and keep it away from strong oxidising agents, strong acids and strong bases. Do not let large spills reach drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$125.78
Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$37.54
![Crommelin Sprayable Exterior Grade Waterproofing 400ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/crommelin-sprayable-exterior-grade-waterproofing-400ml-white-2.jpg?v=1792410554&width=645)
Crommelin Sprayable Exterior Grade Waterproofing is a ready-to-spray rubberised coating for sealing leaks and cracks on outdoor surfaces, supplied here as a 400ml aerosol can in white. It is made for spots that cop regular rain and sun, and it dries to a flexible, watertight layer that can be painted over with most acrylic paints.About the formulaA rubberised waterproofing coating in a pressurised can, so there is no brush, roller or mixing involved. The spray works its way into small holes and cracks to stop water getting through, helps block moisture penetration, and gives metal surfaces a barrier against corrosion. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), fast drying and permanently flexible. The white finish suits light-coloured roofing and masonry.Where to use itIndoors: not intended for interior use, as this is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, and hoses, air conditioner drip pans and ductwork.Suitable materials include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particleboard, PVC piping and fibreglass.How to use itMake sure the surface is clean, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and any other contaminants. Crommelin recommends its Water Rinsable Degreaser for removing grease and oils. Shake the can well, then spray the area to be sealed following the directions on the can. Once the coating has dried it can be over-painted with most acrylic paints. Full application instructions are available on the Crommelin website.Important notesThis product has not been tested for use in potable water systems, so do not use it on drinking water tanks or pipework. It is an exterior grade coating and is not designed as an under-tile or interior wet area membrane. Check the can and the manufacturer's data sheet for drying and recoating times and for surface or ambient temperature limits before starting.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 1 x 400ml aerosol can Colour White Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Overcoating Can be painted over with most acrylic paints Use Exterior Pack dimensions Approx. 64 x 64 x 197 mm SafetyThe can may burst if heated. Use only in well-ventilated areas, avoid breathing the spray, and keep away from heat, sparks, flames and other ignition sources. Wear gloves and eye protection, and remove any contaminated clothing and splashes from skin straight away. Store in a cool, dry place out of direct sunlight, do not expose to temperatures above 50°C, and keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
![Crommelin Exterior Grade Brushable Waterproofer 1L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/crommelin-exterior-grade-brushable-waterproofer-1l-grey-2.jpg?v=1792410528&width=645)
Crommelin Exterior Grade Brushable Waterproofer is a grey, synthetic rubber based liquid membrane for areas that stay wet, including permanent immersion, protected pedestrian areas and surfaces that will be covered by a screed or topping. This 1L pail suits small repairs and compact jobs. It dries to a tough, flexible film that moves with the structure underneath.About the formulaA water based, ready-to-use membrane built on synthetic rubber (styrene butadiene rubber). The manufacturer describes it as low VOC and fast drying, with good adhesion to a wide range of building surfaces. It stays flexible after curing so it can follow structural movement, and it can bridge existing cracks up to 1.5mm. It is suitable for permanent water immersion and, per the manufacturer's technical data sheet, for collecting and storing potable water. Once cured it can be overcoated with screeds, renders and water based coatings.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin makes separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits non-exposed pedestrian areas and applications under screeds and toppings.Suitable surfaces listed by the manufacturer include concrete, brickwork, concrete blocks, cement render, screeds, fibre cement sheeting, plywood sheeting and steel (suitably prepared or primed). The technical data sheet also lists aluminium and lightweight aggregate block.How to use itSurfaces must be clean, dry and sound, and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Concrete should have cured for at least 28 days, and screeds and renders for at least 7 days. The manufacturer calls for a moisture test to confirm the substrate is dry enough to coat, and recommends an electronic moisture meter. Remove high points, fill blow-holes and honeycombing with a suitable repair mortar, and make good any defects. Masonry should be flush pointed.The product is ready to use, so stir it well before applying. Apply with a brush or roller. Use a bond-breaking sealant in all joints, junctions, protrusions, angles and internal corners, and apply the membrane to the positive side of the substrate. Apply two coats at the recommended rate, running the second coat at right angles to the first once the first is touch dry (about 2 hours). Apply only between 10°C and 35°C and in humidity no higher than 85%. Wash tools with water before the product dries.Important notesAllow a minimum of 72 hours before backfilling and about 7 days for full cure. Ensure good airflow while curing, and do not expose the membrane to moisture until it has fully cured. Protect the membrane from damage, and install suitable protection board before any backfilling. Do not apply in extreme weather or humidity. If the substrate is not dry, the manufacturer advises priming with Crommelin Dampstop, so check the full instructions on the Crommelin website for your substrate. Avoid applying the membrane too thickly in corners, as this can reduce flexibility. This listing is for the brushable (pail) product, not the sprayable aerosol version.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofer (Exterior Grade Waterproofing) Model number 1081-001 Pack 1L pail Colour Grey Base Water based, synthetic rubber (styrene butadiene rubber) membrane Application Brush or roller, 2 coats Coverage About 1.5m² per litre per coat, so about 0.75m² of finished two-coat membrane per 1L Crack bridging Existing cracks up to 1.5mm Recoat time About 2 hours Backfill Minimum 72 hours Full cure 7 days Application conditions 10°C to 35°C, humidity up to 85% Clean up Water, before the product dries Use Exterior, permanent immersion, non-exposed pedestrian areas, under screeds and toppings SafetyIt is stable under normal storage and use, and is incompatible with strong oxidising agents, strong acids and strong bases. Avoid contact with skin and eyes, wash tools and any spills with water while the product is wet, and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$34.76
Gripset Betta Bitumen Rubber is a two-in-one, solvent-free liquid membrane in a 1 litre pail, supplied here for waterproofing underground, immersed and general building work. Apply it as a bitumen polymer membrane, or dilute it with water to make an economical black bitumen paint where a full membrane is not needed.About the formulaA water-based, concentrated bitumen and latex polymer liquid that dries to a flexible black film. The manufacturer describes it as solvent free, with good sealing and adhesion on a range of building surfaces. It can be applied to damp surfaces provided there is no standing water, and it is approved for potable water contact (tested at an exposure of 1000mm2 per litre). Diluted 1:1 with water, 1L of concentrate makes 2L of bitumen paint.Where to use itIndoors: interior areas that need a waterproof or protective coating, where a membrane or bitumen paint suits the job.Outdoors: underground and retaining walls, garden beds, planter boxes and landscaped areas, fish ponds, stock troughs and water features, and general protective coating work. It also suits fully immersed applications when applied at the higher immersed coverage rate.Suitable surfaces include concrete, masonry, brick, timber, cement sheeting, metals and aged bitumen, along with other common building surfaces. If you plan to coat over existing paints or finishes, check with Gripset Betta first.How to use itStart with a clean, sound surface free of loose material and standing water. The product is self-priming. For porous surfaces, the manufacturer's literature suggests diluting the first coat with water (about 1 part concentrate to 3 parts water). Use a separate primer on non-porous or smooth surfaces and on surfaces affected by rising damp. Apply by brush, roller, trowel or spray, working each extra coat in a different direction to the one before.As a membrane, apply at least 2 coats at a combined minimum of 1.5 litres per square metre, which gives a dried film of about 1.2mm. For immersed areas, allow a minimum of 2 litres per square metre. Uneven or porous surfaces can need more. For paint use, mix the concentrate with clean water 1:1 by volume. Wash tools in water while the product is still wet.Important notesDrying times at about 20°C: tack free in 60 to 90 minutes, recoat after 2 to 4 hours, dry film in 24 hours, backfilling underground after 4 days, and immersed areas after 21 days. Temperature, humidity and surface porosity all change these times. Once dry, the product has to be removed mechanically or with solvent. For potable water use, wash the surface down and discard the first fill before using the water for drinking. At the minimum membrane rate, 1L covers well under 1 square metre, so check quantities before you buy.Specifications Brand Gripset Betta Product Bitumen Rubber Waterproofing Membrane Pack 1 litre pail Colour Black Base Water-based bitumen and latex polymer, solvent free Application Brush, roller, trowel or spray Membrane coverage Minimum 1.5 L/m2 in 2 coats (2 L/m2 for immersed areas) Paint dilution 1 part concentrate to 1 part water Tack free 60 to 90 minutes Recoat 2 to 4 hours Dry film 24 hours Immersed areas 21 days Clean up Water, while wet Use Interior, exterior, underground and immersed SafetyIt is non-flammable as supplied, but the dried film will burn in a general fire. Wash your hands after use and before eating, drinking or smoking. Do not let it enter drains, sewers or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$27.04
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
Selleys FlexiSeal (ProSeries) is a high-strength, fast-curing polyurethane sealant and adhesive built for tough construction jobs. It seals and bonds expansion and construction joints in both vertical and horizontal applications, staying highly flexible once cured so it can absorb the natural movement of a building without cracking or pulling away. This 600ml grey sausage pack suits a standard sausage gun and is ideal for larger trade and DIY jobs. Key features High-strength, flexible grey polyurethane adhesive and sealant Handles up to ±25% joint movement Non-slumping, low-modulus formula Fast curing and weatherproof for indoor and outdoor use Paintable after cure with no primer needed on most surfaces Excellent adhesion to most common building materials Where to use it Bonds and seals most building materials including concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics. Suitable for indoor and outdoor sealing of expansion and construction joints, around window and door frames, and general weatherproofing. How to use Prepare joints so they are clean, dry and free from oil, dust and curing agents. Use a backing rod for deeper joints. Cut the nozzle, load the sausage into a suitable gun and extrude the sealant, ensuring full contact with both joint sides and avoiding air entrapment. Tool and smooth off with a spatula. Once fully cured, paint if required using water-based paint. For solvent-based paints, undercoat with a water-based primer first. Important notes Applies and cures best at moderate temperatures (around 20°C), especially in cold weather. Will not adhere to PE, PP or PTFE; test other plastics and rubber before use. Not recommended for continuous submersion or below-water-line use. Not ideal over old or incompatible sealants, which may affect cure. Specifications Brand Selleys Product FlexiSeal (ProSeries) Multipurpose Sealant & Adhesive Technology Polyurethane joint sealant Colour Grey Size 600ml sausage Joint movement Up to ±25% Finish Paintable after cure Use Indoor and outdoor Safety Use in a well-ventilated area and avoid prolonged skin contact; wear suitable gloves and eye protection. Uncured polyurethane sealant may cause skin and eye irritation and can sensitise some users, so wash off any residue promptly. Keep out of reach of children. Always read the label and refer to the manufacturer’s Safety Data Sheet before use.
$27.25
Selleys Liquid Nails Flex is a flexible construction adhesive built for jobs that need a strong, lasting hold that can still move. It is designed to stretch a long way under load while keeping its grip, so bonded materials can expand, contract and shift with the building without the join letting go.What it isA high-performance, low-VOC construction adhesive that bonds to most common building materials, porous or non-porous, and will even grab onto damp surfaces. It cures quickly, shrugs off everyday movement and wear, and stays paintable once set.Where to use itIndoors: fixing skirting, architraves, trims, panelling, plasterboard, tiles and general carpentry where a bit of flex is wanted.Outdoors: exterior trims, cladding and general building repairs, thanks to its interior and exterior rating and weather resistance.How to use itCut the nozzle and load the cartridge into a standard caulking gun. Run a continuous bead along studs, joists or battens, or space beads roughly 5cm apart on broad surfaces. Bring the surfaces together within about 10 minutes and brace, clamp or fix mechanically. Leave temporary fasteners in place for at least 4 hours, and use mechanical fixings for high-stress work.Important notesDo not rely on it as the sole support in structural or overhead applications, and avoid tightly clamped joints. Wipe up uncured adhesive with mineral turpentine; once cured it is removed by scraping or sanding.Specifications Brand Selleys Range Liquid Nails Product Liquid Nails Flex Size 430g Type Flexible construction adhesive Stretch Up to 400% Gap fill Up to 9mm Standard Meets AS 2753 gap filling VOC Low VOC (under 50 g/L) Use Interior and exterior Clean up Mineral turpentine SafetyUse in a well-ventilated space and avoid prolonged skin contact. Keep out of reach of children. Always read the current Selleys Safety Data Sheet for full handling, first aid and disposal guidance before use.
$11.29
Dunlop Coloured Render Texture Coat is a premixed, coloured acrylic texture coat that delivers a durable, contemporary decorative finish straight from the pail. Tinted in a range of popular Colorbond® colours, it lets you match rendered walls to roofing, gutters and trims without painting afterwards. The easy trowel-and-float formulation applies like a render but finishes like a designer coating, and its protective acrylic film shrugs off weather for a long-lasting, low-maintenance facade.Where to use itFor indoor and outdoor decorative finishing over brick, blockwork, concrete, blueboard and compressed fibre cement sheet — typically as the final coat over a levelled base render such as Dunlop Multipurpose Acrylic Render or Flexible Fine Coat Render. Choose from Surfmist, Dune, Woodland Grey and Monument to complement your colour scheme.How to useEnsure the base surface is clean, dry, sound and uniform; make good any defects with Dunlop Render Joint & Patch first. Stir the pail thoroughly to an even colour, then apply with a steel trowel to a thin, consistent film of around 1mm. While still workable, rub up with a plastic float in a circular motion to develop the characteristic texture. Work wall sections wet-edge to wet-edge to avoid joins, and use pails from the same batch on a single elevation. Tools clean up with water. A 12.5L pail covers up to 10m² at 1mm thickness.Important notesColour consistency is best when complete walls are finished in one session from mixed batches. Avoid application in rain, extreme heat or onto damp substrates; drying slows in cold, humid conditions.Specifications Size 12.5L pail Colours Surfmist, Dune, Woodland Grey, Monument (Colorbond®) Coverage Up to 10m² at 1mm per pail Finish Coloured acrylic texture coat SafetyWater-based acrylic coating. Wear gloves and eye protection, avoid skin and eye contact and wash off with water while wet. Keep sealed and away from children, and consult the Safety Data Sheet before use.
$135.40
Dunlop Multipurpose Acrylic Render is a high-performance, polymer-modified render engineered for superior trowelability and a no-sag, no-crack result even at higher builds. It can be applied from 2mm right up to 10mm in thickness without slumping, which makes it equally at home as a levelling base coat over rough masonry or as a straightening coat before a fine or textured finish. One bag covers the jobs a standard sand-and-cement mix struggles with, while remaining easy to rule off and float.Where to use itFor indoor and outdoor rendering over AAC panels and blocks, brickwork, concrete blockwork and concrete walls. Use it to render new masonry, level uneven walls, and build out hollows before finishing with Dunlop Ready-to-Go Render, Fine Coat Render or Coloured Render Texture Coat.How to usePrepare a clean, sound, dust-free substrate and dampen very porous masonry or apply the recommended primer. Mix the powder with clean water to a smooth, workable consistency, then apply with a steel trowel at 2-10mm. Rule off with a straight edge, allow to firm, then float or sponge to the desired surface. The Dunlop Gauging Trowel helps achieve a professional finish. As a guide, 20kg covers approximately 6.5m² at 2mm, 2.6m² at 5mm or 1.3m² at 10mm thickness.Important notesDo not exceed 10mm per coat — build very deep sections in multiple passes. Avoid application in direct hot sun, high wind or onto frozen or saturated substrates, and protect fresh render from rapid drying. Allow to cure fully before over-coating or painting.Specifications Size 20kg bag Colour Light Grey Coverage 6.5m² at 2mm, 2.6m² at 5mm, 1.3m² at 10mm per bag Application thickness 2-10mm SafetyContains cement — wet render is alkaline and can irritate or burn skin and eyes. Wear gloves, eye protection and a dust mask when mixing, avoid breathing dust and wash skin promptly after contact. Read the Safety Data Sheet before use.
$23.55
Dunlop Ready-to-Go Render is a premixed white render supplied in a resealable pail, ready to trowel straight onto the wall with no mixing, no dust and no wasted powder. Its easy trowel-and-float formulation makes it one of the most approachable renders for first-time renderers, while still giving experienced applicators a smooth, workable body. Applied at 1-5mm, it delivers a clean, uniform finish over a wide variety of common wall surfaces inside and out.Where to use itSuitable for indoor and outdoor projects over AAC panels and blocks, blueboard, brickwork, concrete walls and sound painted surfaces. Ideal for feature walls, fence walls, garden walls, patching over dated finishes and giving tired masonry a fresh, rendered look.How to useMake sure the surface is clean, sound and free of dust, oil and loose or flaking material; prime porous or painted surfaces as recommended. Stir the pail, then apply the render with a steel trowel to a thickness of 1-5mm, working in manageable sections. Rule off and finish with a float or sponge float once the render has firmed — the Dunlop Sponge Float gives a superior finish. For a higher build over uneven walls, first apply Dunlop Multipurpose Acrylic Render as a base coat and use Ready-to-Go Render as the finishing coat. Tools wash up in water.Important notesKeep within the 1-5mm application range per coat. Avoid rendering in direct hot sun, strong wind or when rain is expected; cold and humid conditions extend drying times. Reseal the pail to keep unused render workable.Specifications Size 16kg pail Colour White Coverage Approx. 6m² at 1mm or 2m² at 3mm per 16kg Application thickness 1-5mm SafetyWater-based premixed render. Wear gloves and safety glasses, avoid skin and eye contact, and wash with water after use. Keep out of reach of children and refer to the Safety Data Sheet for detailed handling information.
$120.29
Dunlop Undertile Waterproofing is a hard-wearing, highly flexible liquid membrane that forms a seamless waterproof barrier beneath tiles. Brushed on straight from the pail, its ready-mixed blue formula makes it easy to see your coverage as you build the film, and once cured it protects the structure beneath showers, laundries and balconies from moisture damage for the long haul.Where to use itDesigned for indoor wet areas such as showers, bathrooms and laundries, as well as balconies. It bonds to AAC blocks, bricks, concrete, renders, screeds, fibre-cement sheet, marine plywood and wet area grade plasterboard on both walls and floors.How to usePrime the prepared surface with the appropriate Dunlop primer, then brush on the first coat of membrane, embedding Dunlop Reinforcing Mat into wall/floor junctions, corners, hobs and joints while it is wet. Once the first coat has dried, apply a second coat at right angles to the first to reach the required film thickness, then tile over it with a compatible Dunlop tile adhesive.Important notesAustralian Standard AS3740 sets minimum membrane thicknesses: after two coats, the dry film must be at least 1mm on floors and 0.5mm on walls. Check your local council requirements before starting. The membrane is certified to AS4858 and AS4654.Specifications Size 12.5kg pail Coverage Approx. 10m² on walls or 4.5m² on floors per pail Substrates AAC, brick, concrete, renders, screeds, fibre-cement, marine plywood, wet area plasterboard Colour Blue SafetyEnsure good ventilation, wear gloves and safety glasses, and avoid skin and eye contact. Keep the pail sealed and stored away from children. Read the Safety Data Sheet before application.
$142.94
Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Blast away built up grime, dirt, and weather stains across large outdoor areas with this powerful concentrate. Designed for Aussie backyards, it cuts through tough mess on concrete, pavers, brick, tiles, and timber or composite decks so outdoor spaces look fresh and inviting again. Why you will love it Heavy duty clean that tackles road film, mildew stains, leaf tannins, and greasy marks. Concentrated value so one bottle makes multiple buckets of ready to use solution. Fast results with minimal scrubbing on most surfaces. Versatile for driveways, decks, paths, patios, and outdoor walls. Hose or pressure washer friendly for quick coverage on big jobs. Ideal surfaces Concrete driveways and garage floors Pavers, brick, stone, and outdoor tiles Timber decks and composite decking Rendered walls and fencing Outdoor furniture settings made of hard materials Dilution guide Job type Mix ratio Where to use Heavy build up 1 part cleaner to 4 parts water Oil spots, mildew stains, leaf marks on concrete and pavers General cleaning 1 part cleaner to 10 parts water Routine driveway and deck washes Maintenance 1 part cleaner to 20 parts water Frequent quick cleans and large areas Coverage: A 5L concentrate can make many litres of solution and clean a large area depending on dilution, surface porosity, and soil level. How to use Sweep the area to remove loose debris. Mix to the required ratio in a bucket or pressure washer reservoir. Wet the surface, then apply generously with a garden sprayer, watering can, mop, or pressure washer. Allow 3 to 5 minutes contact time. Do not let the solution dry on the surface. Agitate stubborn spots with a stiff outdoor broom or deck brush. Rinse thoroughly with a hose or pressure washer, pushing residue to drainage. Tips for best results Test on a small hidden patch first to confirm surface compatibility and desired result. Work in the shade on cool surfaces for even cleaning. On timber decks, scrub along the grain and rinse well. Repeat a light application rather than over concentrate for delicate areas. Important information Not recommended for raw or polished natural stone that is sensitive to cleaners. Always patch test first. Avoid use on freshly sealed surfaces. Check sealer instructions before cleaning. Keep runoff away from ponds and delicate plants. Pre wet adjacent garden beds and rinse after cleaning. Safety Wear gloves and eye protection during mixing and application. Ensure good ventilation if using in semi enclosed areas. Store upright in a cool dry place out of reach of children and pets. Specifications Size 5L concentrate Form Liquid cleaner Application Bucket, sprayer, or pressure washer Suitable areas Driveways, decks, patios, paths, outdoor walls What is in the box 1 x Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Frequently asked Will it remove oil stains Heavy oil may require a second application and some scrubbing. For long standing or deep oil, use a degreaser first, then follow with this cleaner for an even finish. Can I use it with a pressure washer Yes. Mix in the detergent tank as per the dilution guide, apply from the bottom up, allow dwell time, then rinse from the top down. Is it safe for sealed decks Patch test first and follow the sealer brand care instructions. Rinse well after cleaning. Good to pair with Outdoor deck brush or stiff broom for agitation Garden sprayer or pressure washer for fast coverage Protective gloves and safety glasses for safe handling
$27.15 $20.89
Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.
$20.74
Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.
$21.58
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$50.18
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. Do not ingest. Refer to the Safety Data Sheet (SDS) for full details. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$34.90
Dunlop AAC Block Construction Adhesive 15 kg is a reliable thin bed adhesive for autoclaved aerated concrete blockwork chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 15 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Dunlop AAC for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Dunlop AAC Block Construction Adhesive 15 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Laying AAC blocks in internal and external walls Creating straight and plumb courses with minimal waste Suitable surfaces The adhesive works well on the following surface types when properly prepared: AAC blocks and panels Suitable primed substrates as per system design Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of follow bag guidance for open time and pot life. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix to a creamy consistency and apply with a notched trowel. Align blocks within the open time and tap to level. Allow to set before further work. Temperature and environmental performance Protect fresh work from rain, frost, and high heat. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wash tools with water while material is fresh. Remove spills promptly. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep dry and use within shelf life. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$32.41
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$37.95
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
$33.09
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
$16.48
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force. FEATURES: Extreme tensile strength 1 loop of tape holds 700+ pounds of weight Made with patented Forge-Link™ Technology Waterproof backing High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure UV resistant materials
$36.00
$15.00
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
You have seen 144 out of 214 products
Bonds, fillers and sealants suitable for brickwork in indoor and outdoor settings. Construction adhesives, structural epoxies and flexible sealants address fixing, patching and joints. Prep is critical—remove dust and loose material; prime where specified. Check UV/weather ratings for exterior work. Use the filters to narrow by chemistry, cure speed, temperature rating and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
