Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load): – At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area – At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$143.34
Poly Ultra Nails Construction Adhesive is a high strength, versatile adhesive designed for bonding a wide range of building materials both indoors and outdoors. It offers exceptional adhesion, easy application, and water resistance, making it a reliable choice for construction and renovation projects. Features High strength bonding suitable for multiple materials Repositionable for up to 20 minutes for precise alignment Waterproof once cured Ready to use straight from the cartridge Brown finish for a natural look Suitable Materials Concrete, brick, plasterboard, ceramics Plywood, particle board, aluminium Hardwood, softwood, steel, fibreglass Some plastics (pre-test recommended) Application Instructions Ensure surfaces are clean, dry, and free from dust, grease, or flaking paint. Cut the seal, fit the nozzle, and cut to the desired bead size. Insert into a caulking gun. For wall panelling and sheet flooring, apply 6mm beads along studs or joists in a zig-zag line at 40cm intervals. Bring surfaces together within 10 minutes and press firmly along glue lines. Reposition if needed within 20 minutes. Fix with nails, screws, or clamps for at least 24 hours to ensure bond strength. For contact bonding, apply to one surface, bring together, then separate for 3–5 minutes before rejoining. Clean tools and excess adhesive with mineral turpentine. Technical Information Coverage: Approximately 15 metres of 5mm bead Initial bond: Within 24 hours at 25°C Full cure: Up to 7 days Colour: Brown Important Notes Not suitable for mirrors, polystyrene foam, or continuous water immersion Avoid use on copper-based metals or metals exposed to direct sunlight heat Do not use for tightly clamped joints or heavy loads without mechanical fasteners Safety Information Use in a well-ventilated area and avoid breathing vapours Wear protective gloves and eye protection Keep away from heat, sparks, and open flames Keep out of reach of children If swallowed, do not induce vomiting — contact a doctor or Poisons Information Centre (AUST 131 126; NZ 0800 764 766) Contains 30% w/w liquid hydrocarbons
$4.85
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. If in eyes, rinse with running water and seek medical advice. Keep out of reach of children. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$34.90
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
SikaBond is a high strength contact adhesive that will not slump on vertical surfaces. It can be used as a one way liquid adhesive, or a two way contact adhesive, on a variety of surfaces. Uses SikaBond can be used on most substrates due to its excellent adhesion. These include: Floor and wall panels. Wood, plasterboard and chipboard. Aluminium, iron and steel. Concrete, cement sheeting and masonry. Advantages One component ready to use. Fast drying time. Easy to use. High adhesion strength. Non-slump. Storage and Shelf Life Stored in the original sealed packaging at temperatures of between 5ºC and 35ºC, this material will keep for at least twelve (12) months. Instructions for Use Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking must be removed and light sanding is recommended. Application One Way Method: This method is recommended for heavier panels or where load or stress is expected. Apply a 4 to 6mm bead of SikaBond using a cartridge gun, making sure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges. Two Way Method: Apply adhesive as in one way method, bring together substrates, and press firmly over entire surface to transfer adhesive. Then pull apart. Allow adhesive to tack off for 3 to 5 minutes depending on weather conditions, reposition the objects and press together firmly. The surfaces should be tapped together with a hammer and a padded block to ensure maximum contact. Maximum bond strength will be achieved in 12 to 72 hours, depending on substrates and weather. Heavy panels may require temporary mechanical fastening until maximum strength is achieved.
$5.24
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
Usage Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. Advantages Up to 4 hours fire resistance according to AS 1530.4 Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Movement capability of ± 35% (ASTM C 719) Easy to smooth and very good workability Good adhesion to many different substrates Neutral curing Colour Grey
$23.70
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
Usage Aluminium Composite materials Panels(ACP) Glass Metals Coated and painted metals Plastics Wood Advantages Excellent adhesion High movement capability Weather resistant Outstanding UV resistance High strength Interior & Exterior Permanent flexibility Colour Transparent
$18.18
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
Sika Firerate is a gunnable acrylic based jointing and sealing compound specially formulated with inorganic fillers to provide a fire barrier. Sika Firerate has been tested for fire resistance for up to 4 hours according to AS 1530.4 in masonry wall and floor joints. USE Sika Firerate is suitable for sealing joints in concrete or masonry that must have a fire rated resistance to Australian Standards. Sika Firerate also fulfils the basic function of a gap filler and joint sealant against water and dust penetration. CHARACTERISTICS AND ADVANTAGES Safe to use – contains no asbestos or fibres. Paintable. Good flexibility and adhesion to concrete and masonry. Interior use only. Easily applied with normal caulking equipment. Easy tooling off. Economical – single product for both fireproofing and sealing functions. Water clean-up of tools and equipment while still uncured. Excellent acoustic performance, test report available. COLOUR Grey CHARACTERISTICS/ADVANTAGES • Up to 4 hours fire resistance according to AS 1530.4 • Very good resistance to weathering • Movement capability of ± 20 % • Easy to smooth and very good workability • Good adhesion to many different substrates • Water clean-up of uncured sealant . APPROVALS / STANDARDS • AS 1530.4 FRL • ISO 717.2 Rw (Ctr) = 64 (-13) SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sika® Firerate adheres without primers and/or activators. APPLICATION METHOD / TOOLS Sika® Firerate is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sika® Firerate into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sika® Firerate sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Water can be used if wet tooling is required. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with water. Once cured, residual material can only be removed mechanically LIMITATIONS • Sika® Firerate may be overpainted with solvent free paints. • Do not use Sika® Firerate on damp and/or wet substrates. • Do not apply Sika Firerate at temperatures below 5ºC • Do not use Sika® Firerate to seal joints in and around swimming pools. • Do not use Sika® Firerate to seal joints in external applications on non-porous substrates. • Do not use Sika® Firerate for joints under water pressure or for permanent water immersion. • Do not expose uncured Sika® Firerate to rain or water as this may interfere with the curing reaction. BASIS OF PRODUCT DATA All technical data stated in this Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. ECOLOGY, HEALTH AND SAFETY For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety related data.
$25.69
Sika AnchorFix®-1 is a high-performance, styrene-free chemical anchoring adhesive designed for fast and reliable installations in both construction and DIY projects. This two-component, solvent-free, polyester-based adhesive is ideal for securing rebars, threaded rods, bolts, and special fastening systems in concrete, hollow and solid masonry, hard natural stone, and solid rock. It cures rapidly, even in low temperatures, and can be applied using standard guns. Advantages: Fast curing Compatible with standard guns Usable in low temperatures High load capacity ETA approved Non-sag, even overhead Styrene-free Low odor and wastage Technical Information: Compressive Strength: ~60 N/mm² (7 days, +20°C) Modulus of Elasticity in Compression: ~3,500 N/mm² Tensile Strength in Flexure: ~28 N/mm² Tensile Strength: ~12 N/mm² Temperature Resistance: +50°C (long-term), +80°C (short-term) Glass Transition Temperature: +60°C Color: Component A: White Component B: Black Mixed: Light grey Usage: Ideal for various grades of rebars, threaded rods, bolts, and special fastening systems. Substrates may vary, so testing is recommended to ensure suitability, especially with natural stones. Always ensure the substrate is clean, dry, and free of contaminants. Perform pull-out tests if the substrate strength is unknown. Mixing and Application: Mix the components in a 10:1 ratio by volume. The material must be between +5°C and +40°C for application. Ensure the substrate temperature is between -10°C and +40°C. Shelf Life and Storage: Shelf life is 12 months from the date of production when stored properly. Store in unopened, sealed, and undamaged packaging in dry conditions between +5°C and +25°C. Curing Times: +30°C: Open time 4 minutes, Curing time 35 minutes +25°C: Open time 4 minutes, Curing time 40 minutes +20°C: Open time 5 minutes, Curing time 50 minutes +10°C: Open time 6 minutes, Curing time 85 minutes +5°C: Open time 10 minutes, Curing time 145 minutes -10°C: Open time 30 minutes, Curing time 24 hours Approvals and Certifications: Complies with NCC 2019 reference to AS 5216:2018 for post-installed and cast-in fastenings in concrete. ETA-approved for use in masonry and non-cracked concrete, with CE marking. Cleaning of Equipment: Clean tools with Sika® Colma Cleaner immediately after use. Hardened material can only be removed mechanically. For detailed design considerations, refer to "Technical Documentation Sika AnchorFix®-1" (Ref: 870 43 01).
$38.30
Sika MaxTack® is a one part high strength, copolymer dispersion adhesive. Uses Sika MaxTack® is a multipurpose high strength, high initial grab adhesive for bonding building materials indoor and in sheltered outdoor areas. - Sika MaxTack® has strong adhesion on various porous materials such as concrete, mortar, fiber cement, wood and painted substrates or decorative pieces. - Sika MaxTack® is suitable to bond decorative parts as skirting board, wood frame, panel, terra cotta tile, anodised aluminium, hard PVC profiles, polystyrene moulding and panel, polystyrene ceiling tile, wood stick and moulding. For other substrates and specific paints: carry out pre-trials. Characteristics: Advantages - Good workability - Powerful grab properties (green strength) - Odourless - Nail-free fixing - For interior use on wall and ceiling - For sheltered outdoor use on wall (canopy, balcony) - Over paintable by an emulsion waterborne paint - Bonds to a wide range of substrates Colour Off white Shelf Life: 18 months from the date of production if stored in undamaged original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10°C and +25°C. Sika MaxTack® must be protected from frost.
$14.52
![Selleys Wet Area Silicone Sealant Speed Seal 1 Hour [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697122629_597e18e6-75e4-42a2-a468-6311b7fae1b1.jpg?v=1754711756&width=645)
$18.00
Sil-X advanced polymer technology is formulated to deliver superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Sil-X has been specially developed to withstand the tough Australian and New Zealand conditions. Selleys THE ONE Adhesive delivers superior bond strength on any building surface. Can be applied to wet or dry, interior or exterior, porous or non porous surfaces*. Extreme versatility that takes the guess work out of DIY. Features Strong bond on any building material Can be applied to wet or dry surfaces Suitable for interior and exterior applications Can be used on porous and non-porous materials Will adhere to oily surfaces Low VOC Excellent weather resistance Flexible and long lasting Paintable with water-based paints What materials is this product suitable for? Suitable for all building materials* How to use this product Ensure surfaces are clean and free from grease or loose particles. Cut tip of cartridge, fit nozzle and cut at 45ºangle to desired size before placing in a cartridge gun such as Selleys Light Speed Caulking Gun. Apply with a caulking gun, pushing adhesive onto the surface. Position pieces and press firmly together. Larger, heavier materials may need to be supported until the adhesive cures. If painting, paint with water-based paint. Handy tips Keep a pack of SELLEYS Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. Limitations *Not for PE, PP, PTFE, or permanent water immersion Clean up Clean up with turps before the adhesive cures. Safety tips Keep out of reach of children. Avoid skin and eye contact and breathing vapours. Use in a well ventilated area. Wear protective clothing, gloves and eye protection. If on skin, wash with soap and water. Cure product before disposal. Product releases methanol during cure.
$17.00
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$18.00
Selleys Paint Over Sealant is a permanently paintable sealant. Features Paintable Smooth flawless finish. Easy to use and can be used on damp surfaces. Superior adhesion to most building materials. Low odour so can be used in any environment without discomfort. Weather resistant by forming a durable seal which remains flexible, not drying or cracking Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch. Temperature resistance – approximately -40°C +93°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. May be discoloured by contact with alloys containing brass, copper or zinc. Do not allow unused product to freeze. Where can this product be used? 10879.Window frames that need painting 102879.Capstones Masonry walls that need painting Perfect for use on or around: Bricks and concrete Windows frames Tiled and wooden fixtures Areas where a sealant is needed and where you want to paint it Not suitable for use in below waterline applications. Not suitable for use on oily woods such as cypress, teak or cedar. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Fibre Cement Painted Surfaces Ceramics Masonry Most metals Most plastics Wood How to use this product Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant. Remove the tape before the sealant skins. For a better finish use a spatula dipped in detergent and water to tool off the sealant. Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. To improve the paint finish, wipe the sealant with detergent solution immediately before painting. Avoid smearing sealant on the surrounding surfaces as this may effects its paintability. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$25.00
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/b491df0a1d2e4750abba298eed7eeb4d.jpg?v=1757753045&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$20.00
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint. Features Available in a great colour range, so no need to paint. Paintable if required. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application). Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack Is formulated for long term resistance to cracking and crumbling. Is water-based, so can be cleaned up with water. Will not stain building materials. Has good resistance to weathering. Mould and mildew resistance. Where can this product be used? Between window and door frames and the wall. Along skirting boards. Around cornices. Between benchtops and tiles which are not exposed to water. In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm. What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How To Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and apply, forcing product into gap Smooth with a wet finger or spatula Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured- 72 hours or longer in cold weather. Limitations: Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone Sealant. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$15.00
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.00
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](http://gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
$15.00
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](http://gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
$15.00
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$22.93
This multipurpose silicone is a neutral (non-acid) curing, one part sealant for interior and exterior use. It is specially formulated to seal out water in a wide variety of situations, where an excellent quality flexible seal with outstanding adhesion is required. Superior adhesion. Non shrinking. Mould resistant. Low odour. Non corrosive.
$19.00
![Selleys Mortar Works Mortar Filler [Terracota]](http://gluesaustralia.com.au/cdn/shop/files/9300697115331_e7d5a048-59cc-4fa4-b476-9627eaad83a2.jpg?v=1754711856&width=645)
$22.62
![Selleys Mortar Works Mortar Filler [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/1097_1101_d8d532a7-4e5b-44a3-b89a-52d72182b07b.jpg?v=1754711858&width=645)
$22.62
![Selleys Mortar Works Mortar Filler [Off-White]](http://gluesaustralia.com.au/cdn/shop/files/1097_1098_3a815c0b-075e-45ff-be31-667727f8f34f.jpg?v=1754711859&width=645)
$22.62
![Selleys Mortar Works Mortar Filler [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/1097_1099_9875a7c9-e982-43aa-b84f-631469c9da3d.jpg?v=1754711861&width=645)
$22.62
![Selleys Mortar Works Mortar Filler [Charcoal]](http://gluesaustralia.com.au/cdn/shop/files/1097_1100_13fd0c37-596b-4bee-b679-9edb2b3b6d4c.jpg?v=1754711862&width=645)
$22.62
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7ce782d52b264c1db0e928662698e299.jpg?v=1757753227&width=645)
$16.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/51345fd2ddf64a74a03e2c6b9e0d7e1a.jpg?v=1757753232&width=645)
$17.26
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/81e21d7d520d41a280976d39a403b5c9.jpg?v=1757753238&width=645)
$16.00
Flexiseal FC is a fast curing polyurethane Adhesive and Sealant with high flexibility and excellent adhesion. Waterproof+, suitable for indoor and outdoor applications^, paintable after it has cured. Best for : Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. Product Details Where can this product be used? External wall and cladding joints Weatherproofing joints between brickwork, masonry, wood concrete or metal frames Joints in walls, balconies, around window or door frames Joints in bridge and balcony parapets Retaining walls Roofing Acoustic rated walls What materials is this product suitable for? Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. How to Use AS AN ADHESIVE: Apply a bead or small blobs on surface. Assemble parts together and clamp firmly to hold until cured. Remove excess immediately. Initial bond achieved in 24 hours depending on temperature and humidity. Bond strength increases over a few days. AS A SEALANT: Extrude sealant into the joint ensuring full contact with the sides of joint. Avoid entrapment of air. Smooth sealant with spatula forcing it into the joint. For best performance, install joint backing rod (polyethylene or polyurethane foam rod) in the joint to control depth and ensure joint movement. Suitable for +/- 25% joint movement. Complies with ISO11600/F/25HM. Limitations: *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. ^To maximise durability in outdoor applications paint with a suitable exterior paint. Some colours may discolour after exposure to UV radiation. +Not suitable for permanent water immersion or below water line use. Clean Up Mineral turps. Cured product can only be removed mechanically
$19.00
Selleys FlameFlex is a fire and acoustic rated sealant with outstanding product performance. Features Fire rated up to 4 hours according to AS1530.4# Complies with BCA acoustic requirements# Superior UV resistance Suitable for interior and exterior use No primer required before painting Adhesion to wet or damp surfaces Better curing (>5°C) Non-bubbling Paintable with water-based paints after product skins in 60 to 90 minutes (apply paint within 12 hours of sealant application) Low VOC – so can be used in any environment without discomfort Where can this product be used? Perfect for use on and around: Sky lights Walls Patios Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to the cartridge, then place in the caulking gun. Hold caulking gun at 45 angle and gun sealnt ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Storage and re-use Product has a 12 months shelf life when stored unopened, in dry and cool conditions Use within 6 months after opening Clean up Uncured sealant can be removed with Mineral Turpentine Safety tips Not suitable on polyethylene, polypropylene or Teflon. Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well ventilated area. Additional information is provided in the Safety Data Sheet. Product Information Selleys FlameFlex™ is available in Grey in a 435g cartridge. Uses This fire and acoustic rated joint sealant has high UV resistance and can be used indoors and outdoors on most surfaces. External and internal, non-trafficable control joints in concrete, masonry, AAC and brick fire rated construction. Acoustic sealing between most common building materials such as concrete, masonry, aerated concrete, plasterboard, fibre cement, metals, timber and plastic as part of a suitable design. Installation over a wide temperature range High UV exposed applications Technical Features Fire rated up to 4 hours according to AS1530.4 Complies with BCA acoustic requirements No primer required Adhesion to wet surfaces Better curing (>5°C) Non-bubbling Better extrudability (>5°C) No slump Paintable Low VOC Halogen free Isocyanate free How To Use The following should only be used as a guide and the installer should apply all Australian Standards, BCA/NZBC requirements, and best practices when using FlameFlex™. Surface Preparation: Ensure surfaces are clean and free of oil, grease, release agents, dust or loose particles. Porous surfaces should be prepared by grinding, brushing, wiping with cloths or blowing off with oil-free compressed air. Any laitance should be removed from concrete- based surfaces. Non-porous surfaces should be free of scale, rust or oxides and can be degreased with a solvent such as MEK, acetone or mineral turpentine. Some degreasing solvents may leave a residue that should be removed. For neat joints use masking tape on both sides of the joint and remove before skinning Joint Design: Refer to separate section. Cartridge: Cut tip and attach nozzle. Insert in the caulking gun. Cut nozzle to the size required for joint. Application: Extrude sealant smoothly into the joint, while ensuring that all substrates are well wetted out with sealant. Curing: The sealant cures by reaction with atmospheric moisture; therefore cure rate is dependent on humidity, ambient temperature and joint size. Typically, the sealant will form a thick skin within 24 hours and full cure can be expected after 7 days. In dry or cool conditions the sealant cure will be longer. Painting: Paintable with water-based paints after product skins (60 – 90 min). Allow longer times before painting in colder weather. Paint within 12 hours of application. Solvent-based paints may be used after first painting with a water-based paint. Due to a large number of paints and varnishes available, a preliminary test of compatibility is recommended. Joint Design For fire rating, joint width should be between 20mm and 40mm. Minimum joint depth should be 10mm or half the width for joints wider than 20mm. A tight-fitting non-absorbent, non-adhering backing material should be used to ensure the correct dimensions and prevent three-surface adhesion. Suitable materials include open cell foam backer rod or bond-breaking tape. Clean Up The uncured product can be removed with mineral turpentine. Cured product can be removed by mechanical action. Use Poly Cleaning Wipes to remove sealant from the skin. Handy Hints In dry conditions, surfaces can be misted with water to speed up cure. Limitations Not for permanent water immersion or below water-line use Not suitable for use on polyethylene, polypropylene or Teflon.
$22.00
D-MASTIC is an oil-based sealant that forms a skin on exposure to air but remains soft underneath. Designed for sealing windscreens in cars, boats, trucks, and buses, and for metal lap joints in white goods, caravans, bus and truck bodies. Features Forms a surface skin, preventing transfer by touch and dirt pick-up on exposed surfaces Paintable with most alkyd and water-based paints (after the skin has formed). Easy clean-up off non-porous surfaces with mineral turpentine. Convenient to use non-slumping from vertical joints and easily extrudable. Long "open" time assists in the assembly of lap joints. Where can this product be used? Metals Paintwork Lacquered Work Machinery and Engines Sealing windscreens Metal lap joints in whitegoods and automotive bodies What materials is this product suitable for? Metal Glass Painted Surfaces Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as mineral turps. Cut nozzle supplied at an angle and to the required opening. Cut tip off cartridge, fit nozzle and insert in suitable caulking gun such as Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply D-Mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps or kerosene. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Maximum service is achieved when used within joints; it is not recommended to be used as a"skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with a spatula dipped into mineral turps. Uncured product may be removed with mineral turps or kerosene. Cured product can be removed by cutting and scraping.
$21.55
![Selleys Butyl Mastic Rubber Caulking Compound for Vehicles [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697101495_09a144af-33d1-46e0-9c47-6910c6f2672a.jpg?v=1754711927&width=645)
Selleys Butyl Mastic is a synthetic resin, butyl rubber based mastic which forms a smooth tough skin, but remains permanently plastic underneath. It is available Off White. Features Remains permanently plastic under a smooth tough skin Versatile sealant with excellent adhesion to a variety of substrates without the necessity to prime Will not bleed into porous surfaces Non-sag in joints up to 12mm vertical joint Wide service temperature: –35° to +65°C Excellent weathering characteristics Does not corrode metals Good water resistance Life expectancy is approximately 5 years in a thick joint. It is recommended to use silicone sealant in thinner joints Easy smoothing and clean-up with mineral turps or white spirits Where can this product be used? Sealing aluminium windows to masonry. Sealing joints between pre-cast concrete panels or porcelain enamelled panels. Sealing edges of all types of wallboards or wherever a permanent waterproof seal is required. Sealing lap joints between metal applications with the inclusion of fasteners. Ideal for dust proofing cars, trucks, caravans, boats, etc. and is suitable for sealing cracks and gaps around brickwork, roofing and cladding. What materials is this product suitable for? Please contact your store to confirm avaliability, as some stores may have a limited range. The following should only be used as a guide and the installer should apply all Australian Standards, BCA/NZBC requirements, and best practices when installing. Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as white spirits. Cut nozzle supplied at an angle and to the required opening. Cut end off nipple on cartridge, fit nozzle and insert in suitable caulking gun such as the Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of Butyl Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply Butyl Mastic by forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Should not be used where joint movement will exceed ±8%. Maximum service is achieved when used within joints; it is not recommended to be used as a "skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. Surfaces must be clean and dry. Life expectancy in joints is approximately 5 years Interior applications may have greatly extended skin over time due to the reduced presence of sunlight. Allow surface to skin before painting, i.e. approximately 24 hours after application. Butyl Mastic can be painted over using oil or water based paints after the surface has skinned.
$33.47
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
![Selleys Armour Flex High Performance Adhesive [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125262_5e542168-6518-4fbd-97ab-586ab182d6e9.jpg?v=1754711932&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
![Selleys Armour Flex High Performance Adhesive [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125293_a1f282bb-e154-4d4c-812a-1cc8034e1e80.jpg?v=1754711935&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$23.14
You have seen 144 out of 180 products
Cartridge and sausage-pack products applied with a caulking gun for fast, controlled beads on joints, seams and panels. Ideal for perimeter sealing, bathrooms, roofing, façade and construction fixes. Choose non-sag or fast-grab for vertical work; cut the nozzle to the right bead size and work steadily for a clean finish. Use filters to refine by chemistry (silicone, MS polymer, PU), cure speed and temperature rating. Always review the product page and TDS/SDS for prep and cure guidance.
