Dunlop Artificial Grass Adhesive in the value 4 litre can is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia) for laying artificial grass, outdoor carpet and marine carpet across larger areas. Formulated with excellent water and heat resistance, it keeps synthetic turf and outdoor floor coverings firmly bonded through harsh Australian conditions, and is backed by a 10 year guarantee. At roughly 3m² per litre, one 4L can covers around 12m² – ideal for full lawns, entertaining areas and commercial installs.Where to use itBuilt for outdoor projects – synthetic lawns, pool surrounds, balconies, rooftops, courtyards and marine decks – and also suitable for indoor areas such as covered patios. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to usePrepare a clean, dry, dust-free surface. Spread the adhesive evenly using a suitable notched spreader or trowel, working in sections you can cover while the adhesive is wet. Lay the grass or carpet into the adhesive, smooth outwards to expel trapped air, then roll or weight the surface. Keep traffic off until the adhesive has fully cured.Important notesDo not use in extremely hot or cold conditions – apply between 10°C and 30°C – and do not apply when dew or rain is expected before the adhesive has set. Ensure joins are well supported and seams glued continuously for a lasting result.Specifications Size 4 litre can Colour Green Coverage Approx. 3m² per litre (about 12m² per can) Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: ensure good ventilation, keep away from ignition sources and avoid inhaling vapours. Wear protective gloves and eye protection, reseal the can after use and store away from children. Consult the safety data sheet before use.
$97.56
Dunlop Tiler's Mastic is a premium non-slump tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). Built for the demands of modern tiling, its high-grab, non-slump formula is ideal for today's large format tiles, holding them exactly where you place them on walls while still spreading smoothly and easily on floors. As a C2TES1 classified adhesive it offers extended open time, slip resistance and deformability for a strong, flexible bond.Where to use itSuitable for indoor and outdoor walls and floors, including wet areas over Dunlop Waterproofing. It fixes ceramic, porcelain, non-moisture sensitive natural stone, fully vitrified, mosaic and translucent tiles over cement render, compressed fibre-cement sheet (floors), concrete, Dunlop Undertile Waterproofing, existing ceramic tiles, ceramic tile underlay, fibre-cement sheet (walls) and plasterboard.How to useMix the powder with clean water to a smooth, creamy paste. Trowel onto a clean, dry, sound substrate with a 6 x 6 x 6mm notched trowel for walls or a 10 x 10 x 10mm notched trowel for floors and large tiles. Bed tiles with a firm twisting action, checking contact coverage regularly. Grout after approximately 24 hours.Important notesNot suitable for moisture sensitive natural stone. Ensure substrates are properly prepared and primed where required, and avoid tiling in extreme temperatures.Specifications Size 20kg bag Colour White Coverage 10m² with 6mm notched trowel; 6m² with 10mm notched trowel Tile types Ceramic, porcelain, non-sensitive stone, vitrified, mosaics, translucent Substrates Render, concrete, compressed FC sheet, waterproofing, existing tiles, plasterboard Classification C2TES1 tile adhesive SafetyContains cement – avoid breathing dust and avoid skin and eye contact. Wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Consult the safety data sheet before use.
$40.28
Dunlop Tiler's Rubber Modified is a flexible, rubber modified tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). The rubber modified formulation gives the cured bond extra flexibility to absorb normal substrate movement, while its generous coverage and 6-hour grout time keep jobs moving. Classified C2S1, it is a dependable workhorse for tilers who need strength, flexibility and speed in one bag.Where to use itSuitable for indoor and outdoor walls and floors. It fixes ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, ceramic tile underlay, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can even be used over Dunlop Waterproofing and green concrete, making it handy on fast-track projects.How to useMix with clean water to a smooth, creamy consistency and allow to slake before remixing. Apply to a clean, sound, dust-free substrate using a 6 x 6 x 6mm notched trowel on walls or a 10 x 10 x 10mm notched trowel on floors. Press tiles in firmly with a twisting action and check adhesive transfer on the tile back. Grouting can begin in as little as 6 hours.Important notesNot suitable for moisture sensitive natural stone. Do not add extra water once the mix begins to stiffen, and avoid application in extreme temperatures.Specifications Size 20kg bag Colour Grey Coverage 14m² with 6mm notched trowel; 8m² with 10mm notched trowel Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, CTU, waterproofing, plasterboard, render Classification C2S1 tile adhesive; grout in 6 hours SafetyContains cement. Avoid generating and breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated space. Refer to the safety data sheet before use.
$47.18
Dunlop Super Tileset Plus is a smooth, creamy cement-based wall and floor tile adhesive from Dunlop Trade (ARDEX Australia). Mixing to a workable, easy-spreading consistency, it delivers dependable adhesion for everyday tiling at an economical price, making it a solid choice for renovators and trade users tackling standard wall and floor jobs.Where to use itApproved for both indoor and outdoor use on walls and floors. It suits bathrooms, kitchens, laundries, living areas and patios, and bonds ceramic, porcelain, mosaics, fully vitrified, translucent tiles and natural stone (excluding moisture sensitive stone) over concrete, render, screeds, Dunlop Waterproofing Membranes, fibre-cement sheets and plasterboard.How to useMix the powder with clean water to a smooth, lump-free paste and allow it to stand briefly before remixing. Spread onto a clean, dry, sound substrate with a 6mm notched trowel for walls and smaller tiles, or a 10mm notched trowel for floors and larger formats. Bed tiles firmly with a twisting action and check coverage on the tile back periodically. Grouting can proceed after approximately 24 hours at 23°C and 50% relative humidity.Important notesDo not tile over moisture sensitive natural stone with this adhesive, and avoid tiling in extreme temperatures or onto frozen or saturated substrates. Only mix as much adhesive as can be used within its working time.Specifications Size 20kg bag Colour Off-white Coverage 9m² per 20kg (6mm trowel); 6m² per 20kg (10mm trowel) Tile types Ceramic, porcelain, mosaics, vitrified, translucent, non-sensitive stone Substrates Concrete, render, screeds, Dunlop membranes, FC sheet, plasterboard Classification Exceeds C1 Australian Standard SafetyContains cement. Avoid breathing dust and avoid contact with skin and eyes – wear protective gloves, clothing and eye protection when mixing and applying. Mix in a well-ventilated area and refer to the safety data sheet before use.
$36.00
Dunlop Wall & Floor Tile Adhesive is a high performance, ready-mixed adhesive from Dunlop Trade (ARDEX Australia) that takes the hassle out of fixing most tile types. Supplied in an easy-to-handle 8kg pail, it is specially formulated to bond ceramic, porcelain, mosaics, fully vitrified tiles and natural stone (excluding moisture sensitive stone), and its highly flexible formulation copes with the small movements that occur in everyday walls and floors.Where to use itSuitable for indoor walls and floors, and outdoor areas provided there is no standing water and sufficient fall for run-off. It bonds over an impressive range of surfaces: cement render and concrete, fibre-cement sheets, existing ceramic and vinyl tiles, Dunlop Undertile Waterproofing, prepared metal surfaces, oil-based painted surfaces, plasterboard and suitably prepared interior timber.How to useMake sure the substrate is clean, dry and free of dust or grease. Spread the adhesive with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles, then bed tiles in firmly with a twisting motion. Work in small sections so a skin does not form before tiling.Important notesDo not use over strip timber floors. Prime particleboard and plywood sheet floors with Dunlop Tile-All before tiling. For fully immersed or pool applications choose a cement-based Dunlop adhesive instead.Specifications Size 8kg pail Colour Grey Coverage 0.8m²/kg (6-8mm trowel); 0.5m²/kg (10-12mm trowel) Tile types Ceramic, porcelain, mosaics, fully vitrified, natural stone (non moisture sensitive) Substrates Concrete, render, FC sheet, existing tiles, vinyl, metal, plasterboard, prepared timber Format Premixed dispersion adhesive SafetyWork in a well-ventilated area, wear gloves and eye protection, and avoid prolonged skin contact. Wash tools and hands with water before the adhesive dries. Keep out of reach of children and consult the SDS before use.
$93.46
Dunlop Premixed Mastic Tile Adhesive is a high performance, ready-to-use wall tile adhesive from Dunlop Trade (ARDEX Australia). Supplied in a convenient 20kg pail, there is no mixing, no mess and no guesswork – just open the lid and start trowelling. Its superior non-slump formulation holds even large format wall tiles and dimensional stone such as marble and granite firmly in place while you work, and its high flexibility and tenacity make it a favourite with tilers who want dependable grab straight off the trowel.Where to use itDesigned for indoor walls only. It is ideal for bathrooms, kitchens, laundries and splashbacks, and its unique formulation allows use in wet areas. Fix ceramic wall tiles, granite and marble (excluding moisture sensitive stone) over cement render, plasterboard, fibre-cement sheet, suitably prepared painted surfaces and Dunlop Waterproofing Membrane (porous tiles only).How to useEnsure surfaces are clean, dry and sound. Spread the adhesive with a suitable notched trowel, working in manageable sections, then press tiles firmly into the ribs with a slight twisting action. Adjust tiles within about 45 minutes of laying (at 23°C and 50% humidity). The adhesive dries in approximately 24 hours depending on temperature, and the porosity of the surface and tiles, after which grouting can proceed.Important notesDo not use over waterproofing membranes with dense or glazed tiles – use porous tiles only, as the adhesive will not dry properly between two non-absorbent layers. Not suitable for floors or exterior applications.Specifications Size 20kg pail Colour White Coverage Approx. 8-10m² per 20kg Tile types Ceramic wall tiles, granite, marble (not moisture sensitive stone) Substrates Render, plasterboard, FC sheet, painted surfaces, Dunlop membrane (porous tiles) Classification D2TE dispersion adhesive SafetyUse in a well-ventilated area and wear protective gloves and eye protection. Avoid skin and eye contact, wash hands after use and keep out of reach of children. Refer to the safety data sheet before use.
$99.60
Dunlop Builder's Bond is a high strength, multipurpose, rapid-cure epoxy bonding and repair system that joins almost any building material to almost any other. Dispensed through a self-mixing nozzle from a convenient 254ml dual cartridge, its non-sag formula holds firm on walls and even overhead, and cures stronger than concrete in about 2 hours.Where to use itSuitable for indoor and outdoor use across floor, wall and overhead repairs. Typical jobs include bonding concrete, masonry, stone, metal and timber components, rebuilding broken edges and corners, anchoring fixtures, and general structural gap filling where a fast, very strong bond is required.How to useEnsure both surfaces are clean, dry and free of dust, grease and loose material. Load the cartridge into an applicator gun, fit the self-mixing nozzle and dispense the evenly mixed epoxy directly onto the repair or bond line. Shape and tool it before it stiffens. Once cured, Builder's Bond can be shaped, sanded, drilled and painted, so repairs can be blended invisibly into the surrounding surface.Important notesNew concrete must be fully cured - a minimum of 28 days old - before bonding. The non-sag consistency suits vertical and overhead work but is not a pourable grout. Start a fresh nozzle for each session, as mixed product hardens inside the nozzle.Specifications Size 254ml dual cartridge Coverage Depends on bead size and gap width Substrates Concrete, masonry, stone, metal, timber and most building materials Set time Stronger than concrete in 2 hours Finish Sandable, drillable and paintable once cured SafetyUncured epoxy resins and hardeners can cause skin irritation and sensitisation. Wear nitrile gloves and eye protection, ventilate the work area, avoid skin contact and wash immediately if contact occurs. Keep cartridges sealed and out of reach of children.
$61.79
For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal 31-42 Clear 5-Minute Epoxy Adhesive 50ml Dual Cartridge Loxeal 31-42 is a two-part, fast-setting structural epoxy that cures colourless and transparent, making it ideal for repairs where the glue line needs to stay invisible. Supplied in a convenient 50ml dual cartridge (1:1 ratio) with a mixing nozzle, it dispenses perfectly proportioned adhesive with no weighing or hand mixing. With a working time of around 5 minutes and handling strength in 20–30 minutes, it bonds metals, ferrite, ceramic, marble, glass, concrete, wood and some rigid plastics. Why choose Loxeal 31-42? Dries clear – colourless, transparent bond line suits glass, ceramics and visible repairs Fast 5-minute set – 3–8 minute working time, functional strength in 20–30 minutes No-mess 1:1 dual cartridge with mixing nozzle for accurate, on-part dispensing Gap filling from 0.1 to 2.0 mm for less-than-perfect joints Durable bonds with excellent resistance to water, gasoline, motor oil and cooling gas Easy enough for DIY, strong enough for the workshop Typical applications Structural bonding of metals, ferrite, ceramic, marble, glass, concrete and wood Bonding some rigid plastics such as polyester, ABS and rigid PVC Joining dissimilar materials in one fast operation Household, automotive, hobby and workshop repairs needing a clear, rigid bond How to use Lightly abrade the surfaces, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the cartridge and discard the first 3–5 cm of extruded adhesive. Apply the mixed adhesive directly to one surface. Assemble the parts immediately and hold them together, without mechanical stress, until handling strength is reached. Remove uncured excess with acetone or a compatible solvent-based cleaner; cured adhesive can only be removed mechanically. Cure times Pot life (working time): 3–8 minutes at +25°C Functional cure: 20–30 minutes at +25°C Strength continues to develop over the following hours; gentle heat accelerates cure Specifications Chemistry Two-part epoxy (resin / amine hardener) Colour (mixed) Colourless / transparent Mixing ratio 1:1 by volume Pot life (+25°C) 3–8 minutes Functional cure 20–30 minutes Shear strength (steel, ISO 4587) 12–14 N/mm² Peel strength (ISO 4578) 4–20 N/25mm Hardness Shore D 65–75 Gap fill 0.1–2.0 mm Service temperature -40°C to +80°C Pack size 50ml dual cartridge (DCT) with mixing nozzle Shelf life 1 year unopened at +5°C to +25°C Important notes Not suitable for rubber, soft materials, polyethylene (PE), polypropylene (PP) or PTFE Apply at temperatures above +15°C; higher temperatures shorten pot life Avoid mixing large volumes at once – the chemical reaction generates heat Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Work in a well-ventilated area, avoid skin and eye contact, and keep out of reach of children. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$24.95
For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal Metalox Metal Repair Epoxy Kit 10 x 25ml Bi-Syringes Loxeal Metalox is a solvent-free, fast-curing, metal-filled two-part epoxy engineered for repairing and bonding metal components. This trade pack contains 10 x 25ml bi-syringes, each supplied with mixing nozzles, so every job starts with fresh, accurately proportioned adhesive. Its thixotropic (non-sag) paste works as an adhesive filler – rebuilding metal castings, pipework and flanges – and once cured it can be machined, sanded and painted, typically within a few hours of application. Why choose Loxeal Metalox? Trade pack of 10 x 25ml bi-syringes with mixers – fresh 1:1 dispensing on every repair Fast cure – handling strength in around 15 minutes, sandable in about 5 hours at room temperature Strong on steel – lap shear strength of 21 N/mm² on grit-blasted mild steel Machinable, sandable and paintable after polymerisation, even for outdoor repairs Non-sag thixotropic paste stays put on vertical and overhead surfaces Excellent resistance to water and many chemical agents Heat cure option: 1 hour at +60°C speeds cure and boosts final strength Typical applications Repairing metal castings, pipework and flanges Automotive body repair and panel filling Bonding metal substrates, plus concrete, wood and other rigid materials Maintenance and plant repairs where downtime must be kept short How to use Scratch or abrade the surface, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the bi-syringe and discard the first 3–5 cm of extruded product. Apply the mixed adhesive directly to the repair area; work at temperatures above +15°C. Assemble or shape immediately and leave undisturbed until cured. Once cured (sandable after about 5 hours at +25°C), machine, sand or paint as required. Cure times Pot life: approximately 5 minutes at +25°C Handling strength: approximately 15 minutes Sandable: about 5 hours at +25°C (90% of final hardness) Accelerated cure: 1 hour at +60°C for full resistance sooner Specifications Chemistry Two-part epoxy (resin / amine hardener), metal-filled Colour Part A metallic grey / Part B black Mixing ratio 1:1 by volume Pot life (+25°C) Approx. 5 minutes Handling strength Approx. 15 minutes Lap shear strength (ISO 4587) 21 N/mm² (grit-blasted mild steel); 18 N/mm² (stainless steel) Compression strength (ASTM D695) 60 N/mm² Hardness (ISO 868) Shore D 65 Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Shelf life 24 months unopened at +5°C to +25°C Important notes Apply at temperatures above +15°C; higher temperatures and large mixed quantities reduce pot life Avoid mixing excess product – the curing reaction generates heat Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Wear suitable gloves, avoid skin and eye contact, and work in a well-ventilated area. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$289.00
Important: this adhesive needs a companion to cure, and works best with: A Loxeal structural acrylic activator (Activator 20), applied to the mating surface. This is a no-mix, two-part system and will not cure without the activator. Not currently stocked online, please contact us to order it. Loxeal Cleaner 10 Degreaser: clean and degrease both surfaces first, as grease and water prevent adhesion. Loxeal 34-59T Structural Acrylic Adhesive Transparent Gel 150ml Loxeal 34-59T is the transparent gel version of Loxeal's 34-59 series – a fast-curing, chemically activated structural acrylic adhesive used together with a Loxeal Activator (such as Activator 20). No mixing is required: apply the adhesive to one surface and the activator to the other, press the parts together and the joint fixtures in as little as 20–40 seconds. The toughened, thixotropic gel is non-sag on vertical surfaces, bonds ferrites, metals and ceramics, and delivers a wide service temperature range up to +165°C. Supplied in a 150ml pack. Why choose Loxeal 34-59T? Transparent gel formulation for tidy, discreet bond lines No mixing required – cures on contact with the matching Loxeal Activator Very fast fixturing – typical handling time 20–40 seconds High strength – shear strength 20–30 N/mm² with strong impact resistance High temperature capability – service range -65°C to +165°C Non-sag gel suits vertical and overhead application Acid-free chemistry, ideal for high-speed assembly lines Typical applications Structural bonding of ferrites, metals and ceramics (e.g. magnet bonding in motors and speakers) High-speed production and assembly line joining Bonded joints exposed to elevated temperatures, impact and vibration How to use Clean both surfaces with Loxeal Cleaner 10 and allow to dry – water and grease prevent adhesion. Apply the Loxeal Activator to one surface and the adhesive gel to the other. Assemble and press the parts together until handling strength is achieved (20–40 seconds). For gaps larger than 0.5 mm, apply activator to both surfaces before applying the adhesive to one side. Remove excess uncured adhesive with an organic solvent and allow at least 24 hours for full cure before loading the joint. Cure times Handling time (with Activator 20): 20–40 seconds Functional cure: 10–20 minutes Full cure: 24 hours Specifications Chemistry Urethane methacrylate structural acrylic (chemically activated, no-mix) Form Transparent thixotropic gel Viscosity (+25°C) 15,000–25,000 mPa·s (thixotropic) Gap filling 0.05–0.20 mm (activator on both faces for larger gaps) Shear strength (ISO 4587) 20–30 N/mm² Tensile strength (ISO 6922) 20–25 N/mm² Impact strength (ASTM D950) 15–25 kJ/m² Service temperature -65°C to +165°C Pack size 150ml Shelf life 1 year unopened at +25°C Important notes Requires a Loxeal Activator (e.g. Activator 20), applied to the opposing surface – sold separately Not designed for polyolefins (PP/PE), PTFE or soft, flexible materials Store in a cool, dry place away from direct light, at no more than +25°C Specifications shown are for the Loxeal 34-59 series adhesive Safety Consult the Safety Data Sheet (SDS) before use. Avoid skin and eye contact and ensure good ventilation during application. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$119.00
For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: clean and degrease the plastics first for a stronger bond (no primer required). Loxeal Superlox Polyolefin Bonder Kit 10 x 25ml Bi-Syringes Loxeal Superlox is a two-part acrylic adhesive developed to bond polyolefins – polypropylene (PP), polyethylene (PE), HDPE and LDPE – and other notoriously difficult low-surface-energy plastics, without primers, flame treatment or other expensive surface pre-treatments. This trade pack contains 10 x 25ml bi-syringes, each with mixing nozzles, dispensing the two components at a simple 1:1 ratio. It joins polyolefins to each other and to other plastics such as ABS and PVC, and to metals, producing structural joints with high shear and peel strength. Why choose Loxeal Superlox? Bonds the "unbondable" – PP, PE, HDPE and LDPE plus other low-surface-energy plastics No primer or surface pre-treatment required – clean, apply, assemble Trade pack of 10 x 25ml bi-syringes with mixers – fresh adhesive for every job Simple 1:1 mixing ratio through the supplied static mixing nozzles Structural performance – high shear and peel strength on plastics and mixed-material joints Also bonds polyolefins to other plastics (ABS, PVC) and to metals Typical applications Repairing and fabricating PP and PE components: tanks, housings, containers, piping and trim Joining polyolefin parts to dissimilar plastics or metal brackets and fittings Manufacturing and maintenance work on low-surface-energy plastic assemblies How to use Clean the surfaces to remove dust, oil and grease (for example with Loxeal Cleaner 10) and allow to dry. Fit the static mixing nozzle to the bi-syringe and discard the first few centimetres of extruded adhesive. Apply the mixed adhesive to one surface. Assemble the parts promptly and hold or clamp them without movement while the adhesive sets. Leave the joint undisturbed until fully cured before applying load. Cure times Fast curing at room temperature – parts typically fixture within minutes of assembly Allow 24 hours for full strength before placing joints under working load Refer to the Technical Data Sheet for precise fixture and cure data for your conditions Specifications Chemistry Two-part structural acrylic, polyolefin bonder Mixing ratio 1:1 by volume via static mixing nozzle Key substrates PP, PE, HDPE, LDPE and other low-surface-energy plastics; also ABS, PVC and metals Surface preparation No primer or pre-treatment required – clean and dry surfaces only Strength profile High shear and peel strength Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Important notes Work at room temperature; low temperatures slow the cure Use each mixing nozzle for one continuous application – fit a fresh nozzle if work is interrupted Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and avoid skin and eye contact. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$369.00
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 100g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. This 100g workshop bottle is the economical choice for production lines, maintenance teams and busy workshops that go through super glue regularly. Why choose Loxeal Istant 23? Trade-size 100g bottle – keeps high-use workshops and production benches running Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Solvent-free, single part – clear cure with tensile strength of 12–25 N/mm² Typical applications Production assembly and repetitive bonding tasks O-rings, seals and neoprene/NBR rubber components Maintenance and repair across rubber, metal and plastic parts Workshops and trades that need a reliable everyday instant adhesive in volume How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 100g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$54.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 20g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. Supplied in a 20g bottle that suits both the workbench and the kitchen drawer. Why choose Loxeal Istant 23? Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Clear, strong bond line – colourless cure with tensile strength of 12–25 N/mm² Solvent-free, single part – no mixing, no clamping hardware, straight from the bottle Typical applications Everyday repairs across rubber, metal and plastic parts O-rings, seals and neoprene/NBR rubber components Small component assembly in production and maintenance work Household and hobby fixes where a fast, tidy bond is needed How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$17.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 27 Super Glue High Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 27 is a high viscosity, gap-filling super glue based on ethyl cyanoacrylate, made for irregular surfaces on plastic, rubber, metal and ceramic. Its thick 1,200–1,800 mPa·s consistency bridges gaps up to 200 microns without running, and its deliberately slower fixture time lets you adjust and align parts during assembly before the bond locks in. Supplied in a 20g bottle. Why choose Loxeal Istant 27? High viscosity, gap-filling formula – fills gaps of 10–200 microns on uneven surfaces Stays where applied – thick consistency will not run out of the joint or drip Repositioning window – slower fixture allows parts to be adjusted during assembly Strong final bond – tensile strength of 18–25 N/mm² when cured Solvent-free, single part – clear cure straight from the bottle Typical applications Bonding rough, porous or poorly matched surfaces Plastic and rubber parts with irregular mating faces Ceramic repairs where a runnier glue would soak away or drip Assemblies that need a few extra seconds of alignment time How to use Clean and degrease both surfaces and allow them to dry fully. Apply a bead of adhesive to one surface only. Assemble the parts, adjust alignment while the slower fixture time allows, then hold with light pressure. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; phenolic resin 10–40 seconds; aluminium 10–30 seconds; ABS 15–40 seconds; PVC 20–50 seconds; steel 20–50 seconds; zinc 40–100 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 1,200–1,800 mPa·s (high) Gap fill 10–200 microns Fixture time 5–100 seconds, substrate dependent Tensile strength 18–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$22.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 43 Speciale Super Glue Cyanoacrylate Adhesive 50g Loxeal Istant 43 Speciale (43S) is a surface-insensitive, general purpose super glue based on modified ethyl cyanoacrylate. Unfazed by acidic and porous surfaces, it excels at bonding leather, wood, fabric, ceramic and metals where ordinary super glues struggle. It offers proven heat resistance to +120°C (short peaks to +150°C) and is NSF registered for use in and around food processing areas, making it a favourite for demanding trade and industrial work. Supplied in a 50g bottle. Why choose Loxeal Istant 43 Speciale? Surface insensitive – cures reliably on acidic and porous substrates like leather, wood and paper Heat resistant – holds strength up to +120°C, with short-term peaks to +150°C NSF registered – acceptable for use as an instant adhesive in and around food processing areas Very fast on hard-to-glue materials – fabric in 2–20 seconds, leather in 5–15 seconds Strong all-rounder – medium viscosity with tensile strength of 15–25 N/mm² Typical applications Leather goods, footwear and upholstery repairs Woodworking, trim and joinery fixes across many timber species Equipment maintenance around commercial kitchens and food processing plants Fabric, ceramic, metal and rubber bonding in workshops and on site How to use Clean and degrease all surfaces and allow them to dry before applying the adhesive. For low-energy plastics such as PE, PP or PTFE, apply Loxeal Primer 7 first and let it dry. Apply the adhesive sparingly to one surface, then bring the parts together quickly and correctly aligned – the fast cure leaves little room for repositioning. Press firmly for a few seconds until fixed, and keep parts clamped until fully set. Wait 24–72 hours for full cure before applying any mechanical stress. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: paper 1–5 seconds; fabric 2–20 seconds; PVC, ABS and phenolic resin 2–10 seconds; aluminium 2–10 seconds; steel 5–20 seconds; leather 5–15 seconds; ceramic 5–30 seconds; softwoods 5–20 seconds; oak 90–180 seconds. Loxeal Activator 9 can be used to accelerate slow joints. Full cure in 24–72 hours. Specifications Chemistry Modified ethyl cyanoacrylate Colour Clear Viscosity (+25°C) 80–150 mPa·s (medium) Gap fill 10–150 microns Fixture time 1–180 seconds, substrate dependent Full cure 24–72 hours Tensile strength 15–25 N/mm² (ISO 6922) Service temperature -50°C to +120°C (peaks to +150°C) Approvals NSF registered for food processing areas Shelf life 12 months in original unopened packaging Pack size 50g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Not approved for use with pure or gaseous oxygen. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$29.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 25 Super Glue Medium Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 25 is a medium-to-high viscosity super glue based on ethyl cyanoacrylate, designed for bonding plastic, rubber, metal and ceramic – including slightly irregular surfaces where a runny glue would simply drain away. At 350–450 mPa·s it stays where you put it, fills gaps up to 150 microns and fixtures in seconds, with a medium setting speed that gives you a moment to position parts. Supplied in a 20g bottle. Why choose Loxeal Istant 25? Medium viscosity – controllable application that stays put on the joint Handles imperfect surfaces – fills gaps of 10–150 microns Broad substrate range – plastic, rubber, metal and ceramic with one product Fast, strong fixture – tensile strength of 15–23 N/mm² when cured Solvent-free, single part – clean, clear bond line with no mixing Typical applications Repairs on ceramics, ornaments and household items Bonding rubber and plastic parts with less-than-perfect mating surfaces Metal-to-plastic and metal-to-rubber assemblies General workshop, trade and hobby bonding How to use Clean and degrease both surfaces and allow them to dry fully. Apply a modest bead or drops to one surface only. Assemble the parts promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; phenolic resin 5–20 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 350–450 mPa·s (medium) Gap fill 10–150 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 15–23 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$22.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-31 Gasketing Elastic Anaerobic Adhesive 75ml Loxeal 58-31 is a high-performance anaerobic gasketing adhesive that cures to an elastic, flexible film, replacing solid pre-formed gaskets on flange joints. It seals against gases, water, LPG, fuels, oils and a wide range of chemicals, resists shocks and vibration, and keeps sealing from -55°C right up to +180°C. The thixotropic consistency stops the sealant migrating before or during cure, and the red adhesive fluoresces under blue light for easy inspection on the production line. Why choose Loxeal 58-31? Elastic cured film accommodates joint movement while maintaining the seal Higher strength and faster fixture than general-purpose flange sealants Extended service temperature to +180°C Thixotropic — no running or migration on vertical flanges Fluorescent under blue light for quality-control checks Dismantles with standard tools when service is required Typical applications Sealing flange joints on pumps, gearboxes and differential housings where an elastic, vibration-resistant gasket and elevated temperature capability are needed — demanding automotive, transport and industrial maintenance work. How to use Clean and degrease the flange faces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Assemble the parts and hold them in place while curing. Use Loxeal Activator 11 for faster cure on passive metals or at low temperatures. To dismantle, use normal tools (heat to +150°C/+250°C if necessary), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 10–20 minutes, functional strength in 1–3 hours and full cure in 6–12 hours. Cure speed varies with gap, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 70–600 Pa·s Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Breakaway torque (ISO 10964) 15–25 N·m Prevailing torque (ISO 10964) 18–28 N·m Shear strength (ISO 4587) 8–13 N/mm² Tensile strength (ISO 6922) 7–10 N/mm² Impact strength (ASTM D-950) 4–7 kJ/m² Service temperature -55°C to +180°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Fully cured Loxeal 58-31 offers excellent resistance to motor oil and gearbox oil at +125°C through 1,000 hours, excellent-to-good resistance to hot 50% water/glycol mixtures, and moderate resistance to gasoline on prolonged exposure. Important notes Recommended for metal surfaces — seek technical advice before applying to non-metal parts. Uncured adhesive can damage coatings, some plastics and elastomers, and may cause delayed stress-cracking in certain thermoplastics. Store cool and dry at no more than +25°C; do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$59.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-14 Gasketing Anaerobic Adhesive 75ml Loxeal 58-14 is a medium-strength anaerobic gasketing adhesive that forms a flexible in-place gasket between flange faces, doing away with pre-cut solid gaskets. The highly thixotropic formula stays exactly where it is applied without migrating before or during cure, and the cured film seals dependably against gases, water, LPG, fuels, oils and many other chemicals across a service range of -55°C to +150°C. Why choose Loxeal 58-14? One liquid gasket replaces an inventory of pre-formed paper, cork and plastic gaskets Flexible cured film shrugs off shocks and vibration Thixotropic — stays put on vertical and horizontal flanges Fills gaps up to 0.50 mm and compensates for minor surface imperfections Assemblies can be dismantled later with standard workshop tools Typical applications Gasketing and sealing of flange joints on pumps, gearboxes, differential housings and similar close-fitting metal assemblies in automotive workshops, plant maintenance and general engineering. How to use Clean and degrease both flange faces (Loxeal Cleaner 10 recommended). Apply a continuous bead so the joint gap is completely filled. Assemble the parts and hold them in position while the adhesive cures. On passive metals or in cold conditions, accelerate the cure with Loxeal Activator 11. To dismantle, use normal tools (heating the parts to +150°C/+250°C helps if needed), remove cured residue mechanically and clean up with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in around 24 hours. Cure speed varies with gap size, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Orange Viscosity (+25°C) 28,000–100,000 mPa·s, highly thixotropic Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 5–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +150°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Once fully cured, Loxeal 58-14 shows excellent resistance to motor oil and gearbox oil at +125°C out to 1,000 hours, and good long-term resistance to gasoline and to 50% water/glycol mixtures at +87°C. Important notes Formulated for metal surfaces — contact a technical adviser before use on non-metal parts. The liquid adhesive can attack coatings, some plastics and elastomers, and may induce delayed stress-cracking in certain thermoplastics. Store in a cool, dry place at no more than +25°C and never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use and follow standard workshop hygiene practices. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$49.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 59-10 Gasketing High Temperature Anaerobic Adhesive 75ml Loxeal 59-10 is a single-component, medium-strength anaerobic flange sealant with outstanding heat resistance up to +200°C. It cures at room temperature when confined without air between close-fitting metal surfaces, forming a durable in-place gasket that replaces pre-formed gaskets, allows wider machining tolerances and still permits dismantling with normal tools. The cured seal is highly resistant to vibration, heat, water, gases, LPG, oils, fuels and many chemicals. Why choose Loxeal 59-10? Service temperature from -55°C to +200°C — ideal for hot-running assemblies Replaces pre-formed gaskets and assures true metal-to-metal contact Fills gaps up to 0.50 mm, accommodating greater machining tolerances Highly resistant to vibration, oils, hydrocarbons and coolants Parts remain serviceable — dismantle with everyday workshop tools Typical applications Sealing flat, rigid flange joints on pumps, gearboxes, camshaft blocks and motor flanges — anywhere a heat-tolerant, vibration-proof formed-in-place gasket is required. How to use Clean and degrease the mating surfaces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Bring the parts together and leave undisturbed until cured. On passivated surfaces or at low temperature, use Loxeal Activator 11 to speed the cure. For disassembly, use normal tools (heat to +150°C/+250°C if needed), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in 6–12 hours. Cure speed depends on substrate, gap and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red Viscosity (+25°C) 50–300 Pa·s Specific gravity (+25°C) Approx. 1.05 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 6–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +200°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance After full cure, Loxeal 59-10 maintains excellent resistance to motor oil and gearbox oil at +125°C and to 50% water/glycol coolant at +87°C through 1,000 hours; resistance to gasoline is excellent initially, reducing with prolonged immersion. Important notes Recommended for metal surfaces — seek technical advice before use on non-metal parts. Liquid product may damage coated parts and elastomers, and contact with some thermoplastics can induce stress-cracking that is not immediately visible. Store in a cool, dry place at +25°C or below; never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$54.95
Loxeal 30-22 UV-Curable High Viscosity Adhesive 50ml Loxeal 30-22 is a fast-curing, high-strength UV adhesive with a thicker, higher-viscosity consistency designed for glass-to-glass and glass-to-metal bonding. The heavier body gives better control on the joint and lets it bridge gaps up to 2 mm, while its crystal-clear, non-yellowing finish with over 98% light transmittance keeps even generous bond lines virtually invisible — ideal for precious crystal work. Why choose Loxeal 30-22? High viscosity (5,500–7,500 mPa·s) resists flowing off the joint before cure Fills bond lines from 0.03 mm up to 2 mm — more forgiving on uneven parts Cures in seconds under UV light (365 nm) Clear, colourless joints with excellent optical clarity Strong bonds on glass-to-glass and glass-to-metal assemblies Typical applications Glass-to-glass and glass-to-metal bonding in glass furniture, decorative items and crystal ware — especially assemblies with larger or less uniform bond gaps where a runnier adhesive would drain away. How to use Ensure both parts are clean and completely dry. Apply the adhesive to one surface and bring the parts together. At least one part must be UV-transparent — position the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Extend the exposure for wider gaps or substrates that filter UV. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Cure time varies with lamp intensity, distance from the light source, bond-line gap and the light transmittance of the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 5,500–7,500 mPa·s Specific gravity 1.10 g/ml Gap fill 0.03–2 mm Tensile strength (ASTM D-2095-69) 8–12 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering substrates — extend exposure accordingly. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$69.95
Loxeal 30-20 UV-Curable Adhesive 50ml Loxeal 30-20 is a fast-curing, high-strength UV adhesive purpose-made for glass and crystal bonding. Under a suitable UV lamp it sets in as little as 6–10 seconds, and its water-clear finish with over 98% light transmittance makes joints all but invisible — the go-to choice for decorative tableware, household and furnishing accessories, giftware and fine crystal work. Why choose Loxeal 30-20? Cures in seconds under UV light (365 nm) — parts are handled almost immediately Exceptional optical clarity: clear, colourless, non-yellowing joints High bond strength on glass-to-glass and glass-to-metal assemblies Bridges bond lines from 0.03 mm up to 1.5 mm Convenient one-part product — no mixing, cures only where the light reaches Typical applications Bonding glass and crystal in decorative tableware, homewares, furnishing accessories, bonbonnières and gift articles; ideal for precious crystal pieces where the joint must stay invisible. How to use Ensure both parts are clean and completely dry. Apply a small amount of adhesive to one surface and bring the parts together. At least one part must be UV-transparent — align the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Allow slightly longer exposure for larger gaps or tinted substrates. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Actual cure time depends on lamp intensity, distance from the light source, bond-line gap and how much UV passes through the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 2,200–2,900 mPa·s Specific gravity 1.1 g/ml Gap fill 0.03–1.5 mm Tensile strength (ASTM D-2095-69) 10–14 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Cured Loxeal 30-20 shows excellent long-term resistance to alcohol and refrigerant gases and good resistance to gasoline. Sustained exposure to high humidity (90% RH at +40°C) reduces bond performance, so it is best suited to dry indoor service. Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering glass — extend exposure accordingly. Not recommended for permanently damp or wet environments. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$69.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 85-86 Thread Sealant High Temperature Anaerobic Adhesive 50ml Loxeal 85-86 is a high strength anaerobic adhesive for locking and sealing threaded joints on all metals, in both free and forced matings. It maintains its sealing performance up to +200°C and offers high resistance to thermal shock, vibration, water, gas, oils, fuels, refrigerant fluids and many other chemicals – making it the choice for hot pipework, gas lines and demanding sealing jobs where standard sealants fall short. Why choose Loxeal 85-86? Seals and locks in one step with high mechanical strength Keeps sealing up to +200°C (service range -55°C to +200°C) Works on all metals, including free and press-fit assemblies Resists thermal shock, vibration, fuels, refrigerants and many chemicals Generous gap fill up to 0.30 mm on threads up to M56 / 2″ Green colour, fluorescent under blue light, for easy inspection Certified and approved Approved for gas-tight threaded joints to EN 751-1 (DIN-DVGW) WRAS approved for contact with wholesome (potable) water Compliant with the UBA (German Environment Agency) declaration for potable water use BAM certified as a sealant in the presence of gaseous oxygen up to 20 bar at +60°C Typical applications Sealing threaded joints on gas, steam, hot water and heating pipework Potable water fittings (observe the potable-water cure times below) Refrigeration, fuel and industrial fluid lines exposed to heat and vibration How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a continuous bead circumferentially, 1–2 threads back from the leading edge, using enough product to give a complete seal. Assemble and tighten the joint, then wipe off any uncured excess. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 (this may reduce final strength). Cure times at +25°C Handling strength: 10–40 minutes Functional strength: 6–12 hours Full cure: 24–36 hours Before contact with potable water: allow 24 hours at +20°C for brass, copper and cast iron; 7 days for stainless steel and aluminium Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 2,200–4,000 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 15–25 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 40–55 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Recommended for metal thread joints only – contact a technical service before use on other materials. Do not contaminate the adhesive with metal; cut the nozzle to the required bead size. The liquid product can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. High strength – for disassembly, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts, bolts and studs of all types that may need to be dismantled later with standard hand tools. It tolerates minor oil contamination on the parts, so it keeps performing where threads are not perfectly clean. Once cured it resists vibration, corrosion, water, gas, oils, hydrocarbons and many other chemicals, and it holds its sealing properties from -55°C to +200°C (up to +250°C for short periods), with proven unscrewing resistance at +200°C. Why choose Loxeal 55-03? Medium strength – assemblies can be dismantled with normal tools when servicing is needed Tolerates light oil contamination on threads Locks and seals fasteners in one step, stopping loosening caused by vibration Wide service temperature range of -55°C to +200°C Blue colour, fluorescent under blue light, for easy inspection on the production line Seals the thread against ingress, helping prevent rust and fretting corrosion Certified and approved Approved as a gas-tight sealant for threaded fittings to European norm EN 751-1 (DVGW and Gaz de France) WRAS approved – suitable for use in contact with potable water Compliant with the UBA (German Environment Agency) declaration for potable water applications NSF registered in category S4 as acceptable for use as an adhesive in and around food processing areas Typical applications Securing nuts, bolts, studs and screws on machinery, vehicles and equipment subject to vibration Sealing threaded fittings on gas, water and compressed air lines Automotive, plumbing and general maintenance work where later disassembly must remain possible How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before putting the joint into service. On passive surfaces (e.g. stainless steel, plated parts) or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure (this may slightly reduce final strength). Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Viscosity (+25°C) 1,700–9,000 mPa·s, thixotropic Specific gravity (+25°C) 1.07 Max thread size / gap fill M36 / 0.25 mm Shear strength (ISO 10123) 9–13 N/mm² Breakaway torque (ISO 10964) 18–23 N·m Prevailing torque (ISO 10964) 9–16 N·m Service temperature -55°C to +200°C (+250°C short term) Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel, with good resistance to petrol, brake fluid, 50% water/glycol and acetone after 1,000 hours of exposure. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. Not approved for use with pure oxygen or oxygen-rich systems, and not suitable for sealing chlorine or other strong oxidising agents. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$14.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-14 Thread Sealant Anaerobic Adhesive 50ml Loxeal 55-14 is a medium strength anaerobic thread sealant for hydraulic and pneumatic threaded connectors up to 1-1/2″. It replaces PTFE tape and hemp for sealing against gases, water, LPG, hydrocarbons, oils and many other chemicals. A medium thixotropic consistency stops the sealant migrating out of the thread before or during cure, and the cured joint is highly resistant to heat, corrosion, shocks and vibration across a service range of -55°C to +150°C. Why choose Loxeal 55-14? General purpose sealer for hydraulic and pneumatic fittings up to 1-1/2″ Replaces PTFE tape and hemp – no shredding, no re-taping, no clogged valves Medium strength – joints can still be dismantled with normal tools Thixotropic formula stays on the thread instead of dripping or migrating Seals against gases, water, LPG, oils, hydrocarbons and many chemicals Resists shock, vibration and corrosion from -55°C to +150°C Typical applications Sealing threaded connectors on hydraulic and pneumatic systems Pipework carrying water, compressed air, LPG, oils and industrial fluids General plumbing and maintenance sealing of metal pipe threads How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a bead of sealant around the male thread so the gap is completely filled. Assemble and tighten the connection. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 2,500–12,000 mPa·s, thixotropic Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 12–18 N·m Prevailing torque (ISO 10964) 20–30 N·m Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Formulated for metal threads only – contact a technical service before use on other materials. The liquid sealant can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$34.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Medium Strength Anaerobic Threadlocker Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts and bolts of all types that may need to be dismantled later. It tolerates minor oil contamination on parts, so it performs even on as-received fasteners, and it holds its locking and sealing properties from -55°C to +200°C (up to +250°C for short periods). The direct alternative to Loctite 243. Why choose Loxeal 55-03 Oil tolerant: cures reliably on lightly oiled threads without extensive cleaning. High temperature: proven unscrewing resistance at +200°C. Serviceable strength: locks firmly against vibration yet can be dismantled with hand tools. Wide chemical compatibility: resists water, gas, oils, gasoline, brake fluid, ethanol, biodiesel and many chemicals. Blue colour, fluorescent under blue light for easy inspection. Certified and approved Gas: approved as gas-tight sealant for threaded fittings to EN 751-1 (DVGW and Gaz de France). Potable water: WRAS approved and compliant with the German UBA declaration for drinking water use. Food areas: NSF registered category S4 for use as an adhesive in and around food processing areas. Typical applications Locking machine bolts, pump housings, gearbox fasteners and automotive nuts and bolts subject to vibration. Threaded fittings in gas and potable water systems where certified products are required. Maintenance work on equipment where fasteners arrive lightly oiled. How to use Clean and degrease parts where practical (Loxeal Cleaner 10 recommended); minor oil films are tolerated. Apply enough product to completely fill the engaged threads. Assemble the parts and hold for the curing time. On passive surfaces or in cold conditions, Loxeal Activator 11 speeds curing (may slightly reduce final strength). Cure times at +25°C Handling: 10 to 20 minutes Functional: 1 to 3 hours Full cure: 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Strength grade Medium (dismantlable) Viscosity at +25°C 1,700 to 9,000 mPa·s, thixotropic Specific gravity Approx. 1.07 g/ml Friction coefficient Approx. 0.10 Max thread / gap filling M36 / 0.25 mm Shear strength 9 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 23 N·m (ISO 10964) Prevailing torque 9 to 16 N·m (ISO 10964) Service temperature -55°C to +200°C (+250°C short term) Approvals EN 751-1 (DVGW, Gaz de France), WRAS, UBA, NSF S4 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel at room temperature; excellent to good resistance to gasoline, brake fluid and 50 percent water glycol. Important notes For metal fasteners. Liquid product can damage coatings, some plastics and elastomers; stress cracking may develop with some thermoplastics. Not approved for pure oxygen or oxygen-rich systems, and not suitable as a sealant for chlorine or other strong oxidising agents. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. For professional and industrial use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 24-18 Low Strength Anaerobic Threadlocker Loxeal 24-18 is a low strength anaerobic threadlocker for nuts, bolts and screws of all types that need to be easily dismantled later with ordinary hand tools. It locks fasteners against loosening from vibration and thermal cycling while staying serviceable, making it the go-to grade for small screws, adjustment fasteners and parts that see regular maintenance. Why choose Loxeal 24-18 Easy disassembly: low breakaway torque means fasteners come apart with standard tools, no heat needed in most cases. Anti-vibration: prevents self-loosening caused by vibration, shock and temperature changes. Wide chemical compatibility: resists water, gases, oils, gasoline, diesel and many chemicals. Gas approved: DVGW approved as a gas-tight sealant for threaded fittings to European norm EN 751-1. Service temperature from -55°C to +150°C. Purple colour, fluorescent under blue light for easy inspection. Typical applications Locking small screws, grub screws, calibration and adjustment fasteners that require frequent servicing. General automotive, machinery and DIY threadlocking where easy removal matters. Thread sealing of metal fittings where a low strength, dismantlable seal is acceptable. How to use Clean and degrease threads (Loxeal Cleaner 10 recommended). Apply enough product to fill the engaged threads. Assemble the parts and tighten as normal. Allow to cure before putting into service. On passivated surfaces or in cold conditions, use Loxeal Activator 11 to speed curing. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Full cure: up to 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate Colour Purple (fluorescent under blue light) Strength grade Low (easy to dismantle) Viscosity at +25°C 800 to 1,400 mPa·s Specific gravity Approx. 1.05 g/ml Max thread / gap filling M24 / 0.20 mm Shear strength 3 to 5 N/mm² (ISO 10123) Breakaway torque 5 to 8 N·m (ISO 10964) Prevailing torque 2 to 5 N·m (ISO 10964) Service temperature -55°C to +150°C Approvals DVGW gas-tight sealant, EN 751-1 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent resistance to gasoline and brake fluid at room temperature; excellent to good resistance to motor oil, gearbox oil and diesel at +125°C, and to 50 percent water glycol at +87°C. Important notes For metal fasteners. Liquid product can attack some coatings, plastics and elastomers; contact with some thermoplastics may cause stress cracking. Pre-test if unsure. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.
$39.95
Dunlop Ready-to-Go Tile & Grout 250g (White) is a clever 2-in-1 product that works as both a tile adhesive and a grout, straight from the tube. There is nothing to mix and very little mess, which makes it a go-to for small tiling jobs, mosaics and quick repairs or touch-ups around the home. Backed by Dunlop's 10 year guarantee. 2-in-1 ready-to-use tile adhesive and grout No mixing, no fuss, less mess Contains Grout Shield antifungal protection Ideal for mosaics, repairs and touch-ups Suitable for joint widths of 1-5 mm Indoor and outdoor wall use About the formula This white, pre-mixed paste bonds wall tiles and then fills the joints with the same material, so a single tube handles the whole repair. The built-in Grout Shield technology helps resist mould and bacteria, keeping finished joints looking cleaner for longer. Excess can simply be wiped away with a damp cloth while still fresh, and the resealable tube makes it easy to store for future touch-ups. Where to use it Indoors: wall tiles and mosaics in kitchens, splashbacks, laundries and living areas, plus general tile and grout repairs. Suitable over concrete, cement render, fibre-cement sheet, plasterboard and prepared painted surfaces. Outdoors: exterior wall tiles and mosaics. When grouting outdoors, protect the area from extremes of weather for 7 days while it cures. Tile types: ceramic, porcelain and marble wall tiles and mosaics (excluding moisture-sensitive stone). How to use it Prepare the surface so it is flat, firmly fixed, clean and dry, free of dust, oil, grease and loose material. Prime surfaces with Dunlop Primer & Additive and allow to dry. Spread the adhesive with a 4.5-6 mm notched trowel to a minimum 1 mm bed. Press and slide each tile into position for full contact, adjusting within 60 minutes (at 23°C, 50% humidity). Joints can be grouted immediately. Squeeze the material firmly into the joints and compact with a grout float or squeegee, scraping off excess from the tile face. After about 15 minutes, wipe back excess with a damp, small-pored sponge, rinsing often. Once the joint has hardened (approx. 6-24 hours), buff and polish the tiles with a clean, dry cloth. Important notes Not suitable for use in wet areas such as a shower recess, over Dunlop Waterproofing membrane, or in continuously immersed conditions. Do not use the grout in expansion or movement joints. For textured or matt tiles, test ease of cleaning on a spare tile first. Designed for wall tiles and mosaics rather than heavy floor tiling. Specifications Brand Dunlop Product Ready-to-Go Tile & Grout (2-in-1) Colour White Size 250 g Form Pre-mixed, ready-to-use paste Tile types Ceramic, porcelain, marble, mosaics (excl. moisture-sensitive stone) Surfaces Walls Location Indoor and outdoor Joint width 1-5 mm Clean up Water (while fresh) Guarantee 10 year (Ardex Australia) Safety Causes skin irritation and may cause an allergic skin reaction. Causes serious eye damage and may cause respiratory irritation. Use only outdoors or in a well-ventilated area, and wear protective gloves, clothing, eye and face protection. Avoid breathing any mist, vapour or spray. If in eyes, rinse cautiously with water for several minutes, remove contact lenses if easy to do, and seek immediate medical advice. If on skin, wash with plenty of water and remove contaminated clothing. If inhaled, move the person to fresh air. Store locked up and keep out of reach of children. Always read the current Safety Data Sheet before use.
$16.88
Selleys Araldite Ultimate Bond is a grey two-part epoxy adhesive engineered for the most demanding repairs, delivering a durable, long-lasting bond that holds up to 200kg/cm² when fully cured on stainless steel. It is the toughest of the Araldite range, designed to be tug and snap proof for fixes that need to stay put. About this adhesive Two-part system of resin (Part A) and hardener (Part B) mixed in a 2:1 ratio. Bonds a wide range of surfaces with a strong, rigid, durable join. Sets in around 5 minutes and is touch-firm fast, with a low-odour formula. Made from 20% bio-based carbon. Working (usable) time of roughly 3-4 minutes at 20°C, so mix only what you can apply. What it bonds China, ceramic and porcelain Metal Glass Leather (pre-test for compatibility) Rubber (pre-test for compatibility) Wood and timber Most rigid plastics Where to use it Indoor: repairing crockery, ornaments and ceramics, refitting loose furniture joints, bonding metal, glass and timber components, and general household fixes. Outdoor: durable repairs on tools, garden and workshop items where a tough, weather-durable bond is required. Bond strength depends on substrate, bond size and surface preparation, and set times lengthen in colder weather. How to use it 1. Abrade, clean and dry both surfaces so they are free of dust, grease and loose oxides. 2. Snap the cap from the plunger and carefully cut the sealed tips at the end of the nozzle. 3. Apply even pressure to the plunger to dispense both liquids onto a clean disposable surface (2:1 ratio) and mix thoroughly with a spatula. 4. Apply the mixed glue to both surfaces, then bring them together. 5. Hold in place with tape or weights if needed and avoid undue strain on the joint for at least 60 minutes. Cures in 24 hours; maximise the bond area (minimum 2.25cm²) for best performance after full cure. Replace the cap on the nozzle for storage and clean up any uncured adhesive with acetone. Important notes Will not bond PTFE, polyethylene or polypropylene plastics. Bond will soften above 60°C but strength is restored once the temperature returns to normal. May discolour if exposed to UV. Full cure takes more than 72 hours. Not recommended where a clear, invisible bond is required, as the cured adhesive is grey. Specifications Brand Selleys Araldite Product Ultimate Bond Epoxy Adhesive Technology Two-part epoxy Colour Grey Size 30mL Mix ratio 2:1 (Part A : Part B) Working time Approx. 3-4 minutes at 20°C Set time Approx. 5 minutes Cure time 24 hours (full cure >72 hours) Holds Up to 200kg/cm² on stainless steel when fully cured Heat resistance Softens above 60°C, strength restored on cooling Clean up Acetone (while uncured) Safety Danger. Part A causes skin and serious eye irritation and may cause an allergic skin reaction. Part B may be corrosive to metals, causes severe skin burns and eye damage, and may cause an allergic skin reaction. Do not swallow and avoid contact with skin and eyes. Wear eye protection and protective gloves when mixing or using, and avoid breathing dust, vapours or spray. Keep out of reach of children and keep in the original packaging. If medical advice is needed, have the product container or label at hand. Refer to the Safety Data Sheet for full handling information.
$26.99
Tarzan's Grip Wood Glue is a fast, dependable PVA timber adhesive built for everyday woodworking and repairs around the home and workshop. This 250mL bottle delivers a strong, lasting bond on a wide range of timbers, making it a reliable choice for cabinetry, joinery, furniture assembly and general carpentry jobs. The water-based PVA formula spreads smoothly, penetrates porous timber and sets to a tough, near-invisible bond line. Its extended working time gives you room to align and clamp pieces accurately before the glue grabs, while easy water clean-up keeps the job tidy with no harsh solvents. What it bondsIdeal for softwoods, hardwoods, plywood and MDF, and well suited to bonding porous materials to one another. Where to use itIndoor / Interior: furniture making and repair, cabinet and drawer assembly, joinery, trim and moulding, hobby and craft woodwork.Outdoor: this is an interior-grade wood glue and is not intended for fully weather-exposed or submerged applications. How to use it Make sure both surfaces are clean, dry and free of dust, grease and old finish. Apply an even coat of glue to one or both mating surfaces. Bring the parts together, align, and clamp firmly. Wipe away any squeeze-out with a damp cloth before it dries. Leave clamped until set, then allow full cure before stressing the joint. Important notesFor interior use only. Not classified as hazardous or as a dangerous good. Keep the cap closed between uses and store upright. Best results on clean, well-fitted joints with adequate clamping pressure. Specifications Brand Tarzan's Grip Product Wood Glue (PVA) Size 250mL Form Liquid Colour Light yellow Base Water-based PVA Density 1.05 g/cm³ pH 3.5 - 4.5 Clean up Water (while wet) Suitable for Softwoods, hardwoods, plywood, MDF Use area Interior SafetyBased on available information this product is not classified as hazardous under Safe Work Australia GHS criteria, and is not classified as a Dangerous Good for transport. Avoid eye contact and repeated or prolonged skin contact, and avoid inhaling mist or vapour. Wash hands after use and keep away from food and drink. If in eyes, rinse immediately with water; if swallowed, rinse mouth, do not induce vomiting, and seek medical advice. Store in a cool, dry, well-ventilated place out of direct sunlight and away from heat or ignition sources. Keep out of reach of children. Refer to the manufacturer's current Safety Data Sheet for full handling guidance.
$33.75
Loctite EA 9235 (Five Minute E-Pox-E, item EFQ5) is a fast-acting two-part epoxy that mixes resin and hardener in equal parts to form a tough, rigid, high-strength bond in about five minutes. Supplied in a dual-barrel syringe that dispenses both components in the correct 1:1 ratio every time, it is ideal for fast permanent repairs and multi-piece projects across a wide range of household, workshop and trade materials. Once cured it resists water and most common solvents, and can be sanded, drilled and machined. It can also be used as a versatile filler for gap filling, surface repairs and laminating. Bonds: metal, glass, ceramic, china, tile, stone, concrete, wood, fibreglass and most rigid plastics. Where to use it Indoor: repairing ceramics, china and glassware, fixing tools and toys, bonding tiles, and general household and hobby repairs. Outdoor: bonding stone, concrete and masonry, plus garden and workshop repairs. Not recommended for continuously wet areas or prolonged water immersion. How to use 1. Make sure surfaces are clean, dry and free of oil, wax, paint and rust. Roughen smooth surfaces by sanding for a stronger grip. 2. Remove the plug and cut the syringe tip at the marked opening. Stand the syringe upright and press the plunger gently to expel any air. 3. Depress the double plunger to dispense equal parts of resin and hardener onto a disposable surface, then mix thoroughly for about one minute. 4. Apply to both surfaces within one to two minutes of mixing and press together. Support the join for around 10 minutes. 5. Usable strength is reached in about 1 hour and the bond fully cures in 24 hours. Wipe the tips clean and replace the plug for storage. Clean uncured adhesive with acetone before it sets. Cured adhesive can be carefully cut away with a sharp blade. Important notes Not recommended for polyethylene, polypropylene, nylon, non-stick coatings or flexible materials. Not suitable for potable (drinking) water systems, prolonged water immersion, or short-term heat above 150°C. Apply between 4°C and 35°C. Specifications Part number Loctite EA 9235 / EFQ5 Size 25ml dual syringe Chemistry Two-part epoxy (epoxy resin / polymercaptan hardener) Mix ratio 1:1 by volume Set time Approx. 5 minutes Usable strength Approx. 1 hour Full cure 24 hours Cured colour Clear amber Hardness 80 Shore D Service temperature -23°C to 49°C continuous (up to 150°C intermittent) Water resistant Yes Sandable / machinable Yes Paintable No Shelf life 24 months unopened Safety Contains epoxy resin and polymercaptan/amine hardeners. Causes skin and eye irritation and may cause an allergic skin or respiratory reaction. Wear gloves, work in a well-ventilated area and avoid breathing vapours. For eye contact, rinse with water for 15 minutes and seek medical advice. If swallowed, do not induce vomiting and seek medical advice. Keep out of reach of children. Always refer to the Safety Data Sheet before use.
$33.75
Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 5.2kg pail is the trade size for lining whole rooms.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the pail, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the pail label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the pail label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 5.2kg pail Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyNot classified as hazardous and not a scheduled poison. The paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. If it gets in the eyes, irrigate with water for 15 minutes and seek medical attention; skin washes clean with warm soapy water. If swallowed, rinse the mouth, drink water, do not induce vomiting and seek medical advice. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$33.20
Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 1kg tub suits patch jobs and small lining work.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the tub, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the tub label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the tub label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 1kg tub Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyNot classified as hazardous and not a scheduled poison. The paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. If it gets in the eyes, irrigate with water for 15 minutes and seek medical attention; skin washes clean with warm soapy water. If swallowed, rinse the mouth, drink water, do not induce vomiting and seek medical advice. Keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$17.90
Dunlop Ready-To-Go Vinyl Flooring Spray Adhesive is a fast and tidy spray-on adhesive for installing vinyl sheet, vinyl tiles, and vinyl planks with vinyl backing over concrete, underlayment grade plywood, metal, and fibreglass. It delivers an even spray pattern, strong bond, and immediate traffic readiness once rolled. Why choose this adhesive Quick, clean spray application that saves time High initial grab for reliable placement Dry to touch in about 10 to 40 minutes Up to 3 hours open time once tacky Ready for immediate foot traffic after rolling Heat weld flooring 1 hour after installation Suitable with underfloor heating systems Water based acrylic blend with very low odour Suitable substrates Concrete, underlayment grade plywood, metal, and fibreglass. Use on vinyl-backed sheet, tiles, and planks. Not suitable for Cushion-backed flooring products. Surface preparation Ensure the substrate is flat, dry, and free from dust, oil, paint, old adhesive, wax, curing compounds, sealers, and hardeners. Lightly damp-mop concrete to remove fine dust before application. Correct surface imperfections before installation to avoid telegraphing. How to use Ventilate and mask the area to protect adjacent surfaces from overspray. Shake the can well and remove the blue safety tab. Hold the can upright 50 to 76 cm above the substrate and spray in smooth, even passes to achieve a uniform frosted look. Avoid heavy patches and overspray. Lightly re-spray missed areas if needed. Allow to dry until no adhesive transfers to the fingertips. Lay the vinyl and roll firmly within 1 hour using a suitable heavy roller to ensure full contact. The floor is ready for immediate use once rolled. Heat welding can commence after 1 hour. Key technical data Chemical type: water based acrylic blend Dry to touch: approximately 10 to 40 minutes Open time after tack: up to 3 hours Traffic allowance: immediate after rolling Underfloor heating: compatible Appearance when sprayed: milky white frost Storage and safety Store between 10°C and 50°C. Avoid freezing and direct sunlight. Pressurised dispenser. Do not pierce or burn the can, even when empty. Use in a well ventilated area and avoid contact with eyes and skin. Tip: Wipe any overspray from adjacent surfaces with a damp cloth before it dries.
$48.36
Dunlop Tile-All Plus Premixed Tile Adhesive 310ml Tile-All Plus is a single component, silane modified polymer adhesive and neutral curing sealant. It offers high initial tack, strong bonding and excellent flexibility. Use it for fast, reliable repairs in showers, kitchens and bathrooms, for replacing tiles, fitting accessories and finishing joints. It can even be used for minor repairs underwater. Why you will like it High initial grab for confident positioning Flexible bond that resists movement and vibration Neutral cure for a low odour application experience Works as both an adhesive and a sealant Paintable after drying with most common paints (test first) Where to use it Showers, kitchens and bathrooms Replacing loose tiles and fitting trims or accessories Finishing expansion and connection joints Minor underwater fixes on suitable surfaces Suitable materials Glass, tiles, ceramics, timber, plastics, metals, concrete, wall panels, waterproofing membranes, aluminium, polystyrene foam, and glazed tiles. Always ensure surfaces are sound, clean and free from dust, oil, grease and coatings. Slightly damp substrates are acceptable. How to use Remove the aluminium seal at the base of the cartridge. Pierce the inner membrane, fit the nozzle and trim to the required bead size. Apply in stripes to the substrate or the item being fixed. Press parts together firmly within 7 to 10 minutes at 20°C, before skinning begins. For spot fixing, keep glue points 25 to 30 cm apart and confirm the item weight is appropriate. Avoid application below 5°C or above 35°C. Good to know Open time varies with temperature, humidity and substrate. Higher humidity shortens open time. If reusing, remove any skinned layer from the nozzle before the next application. Spills can be wiped away while wet with a clean cloth. Not recommended for chemical resistant applications. Cleanup and storage Clean excess while wet with a cloth. Shelf life is up to 12 months in unopened packaging stored in a cool, dry place at around 23°C and 50 percent relative humidity. Safety Use in a well ventilated area. Avoid skin and eye contact. If contact occurs, flush eyes with water for at least 15 minutes and seek medical advice. Wash skin with soap and water. If inhalation discomfort occurs, move to fresh air. If swallowed, drink water in small portions and seek medical advice. Keep out of reach of children.
$27.98
Boyle Gloss All in One Glue Sealer and Finish 236 ml Seal, glue and finish your craft projects with a single water based formula that dries clear and glossy. Boyle Gloss All in One is ideal for decoupage, paper craft, school projects and home decor. It brushes on smoothly, holds strongly and leaves a protective shine. Key benefits Three in one formula for gluing, sealing and top coating Gloss finish that dries clear and enhances colours Water based and low odour for indoor use Brushes on easily and levels well Great for beginners and experienced makers Best for Decoupage and collage Paper, card and photos Wood, MDF and craft boards Canvas and fabric accents Lightweight embellishments and mixed media Surface compatibility Use on clean, dry and dust free surfaces. Test on a small area first, especially on delicate papers, prints or dyed fabrics. How to use Prepare: Ensure the surface is clean and smooth. Cut and position your paper or embellishments. Glue: Apply a thin even coat to the surface with a soft brush. Press the item in place and smooth out any bubbles. Seal: After the glue layer sets to tack free, brush a light coat over the top. Allow to dry fully. Finish: Add 1 to 3 additional thin coats for a stronger, glossier finish. Lightly sand between coats if a super smooth result is desired. Dry time and coverage Touch dry in about 15 to 30 minutes depending on coat thickness and conditions Recoat after 30 to 60 minutes Allow 24 hours before light handling. Full cure develops over several days Coverage varies with technique. Thin coats give the best clarity and bond Clean up Wash brushes and tools with warm soapy water while wet Wipe any fresh drips with a damp cloth Tips for a glossy result Apply multiple thin coats rather than one heavy coat Work in one direction for the first coat, then cross coat for the second Use a soft synthetic brush or foam applicator to minimise brush marks Important information For indoor craft use Keep out of reach of children Avoid freezing. Store upright with the cap closed tightly Specifications Type: All in one glue, sealer and finish Finish: Gloss clear Base: Water based Size: 236 ml
$11.00
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load): – At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area – At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$143.34
Davco Supamastic is a ready to use white wall tile adhesive for internal areas. It is ideal for porous tiles and porous substrates in residential spaces and delivers non slump performance with easy water cleanup. Key benefits Ready to use paste with fast and easy cleanup White formulation suits light coloured tiles and grout lines Non slump for reliable hold on walls Low VOC Classified D1TE to AS ISO 13007 Best for Internal wall tiling with porous tiles greater than 3 percent absorption Residential dry area floors with porous backed tiles over primed cement sheet or ceramic tile underlay Suitable substrates Fibre cement sheet Plasterboard Ceramic tile underlay Rendered blockwork and brickwork Davco K10 Plus waterproof membrane on walls only Tile types Ceramic and mosaics Natural stone that is not moisture sensitive Not suitable for Porcelain tiles larger than 200 x 200 mm Concrete substrates Moisture sensitive stone Coverage Approximate coverage with a 6 mm notch trowel: 4 L covers about 3 m². Application guide Ensure the substrate is sound, clean, dry and properly primed. Spread adhesive with a suitable notch trowel at about 60 degrees and comb in one direction. Press tiles firmly into the ribs and slide across the rib direction to collapse the ribs and remove voids. Back butter large format tiles if required to achieve full coverage. Clean excess adhesive from joints and tile faces with a damp sponge while wet. Set and cure times at 22°C and 50% RH Open time: about 30 minutes Adjustability: about 45 minutes Grout after: 24 hours Dry area service: 48 hours Wet area service: 7 days Practical limits Layer thickness up to 4 mm Apply and cure between +5°C and +35°C ambient and substrate temperatures Drying times extend in cool weather, over membranes and with low porosity tiles Good to know If tile or substrate porosity is uncertain, consider a suitable alternative adhesive from the same brand for low porosity tiles. Install movement joints to applicable standards and allow adequate drying before grouting.
$66.24
Davco Supamastic is a ready to use white wall tile adhesive for internal areas. It is ideal for porous tiles and porous substrates in residential spaces and delivers non slump performance with easy water cleanup. Key benefits Ready to use paste with fast and easy cleanup White formulation suits light coloured tiles and grout lines Non slump for reliable hold on walls Low VOC Classified D1TE to AS ISO 13007 Best for Internal wall tiling with porous tiles greater than 3 percent absorption Residential dry area floors with porous backed tiles over primed cement sheet or ceramic tile underlay Suitable substrates Fibre cement sheet Plasterboard Ceramic tile underlay Rendered blockwork and brickwork Davco K10 Plus waterproof membrane on walls only Tile types Ceramic and mosaics Natural stone that is not moisture sensitive Not suitable for Porcelain tiles larger than 200 x 200 mm Concrete substrates Moisture sensitive stone Coverage Approximate coverage with a 6 mm notch trowel: 4 L covers about 3 m². Application guide Ensure the substrate is sound, clean, dry and properly primed. Spread adhesive with a suitable notch trowel at about 60 degrees and comb in one direction. Press tiles firmly into the ribs and slide across the rib direction to collapse the ribs and remove voids. Back butter large format tiles if required to achieve full coverage. Clean excess adhesive from joints and tile faces with a damp sponge while wet. Set and cure times at 22°C and 50% RH Open time: about 30 minutes Adjustability: about 45 minutes Grout after: 24 hours Dry area service: 48 hours Wet area service: 7 days Practical limits Layer thickness up to 4 mm Apply and cure between +5°C and +35°C ambient and substrate temperatures Drying times extend in cool weather, over membranes and with low porosity tiles Good to know If tile or substrate porosity is uncertain, consider a suitable alternative adhesive from the same brand for low porosity tiles. Install movement joints to applicable standards and allow adequate drying before grouting.
$81.13
Poly Ultra Nails Construction Adhesive is a high strength, versatile adhesive designed for bonding a wide range of building materials both indoors and outdoors. It offers exceptional adhesion, easy application, and water resistance, making it a reliable choice for construction and renovation projects. Features High strength bonding suitable for multiple materials Repositionable for up to 20 minutes for precise alignment Waterproof once cured Ready to use straight from the cartridge Brown finish for a natural look Suitable Materials Concrete, brick, plasterboard, ceramics Plywood, particle board, aluminium Hardwood, softwood, steel, fibreglass Some plastics (pre-test recommended) Application Instructions Ensure surfaces are clean, dry, and free from dust, grease, or flaking paint. Cut the seal, fit the nozzle, and cut to the desired bead size. Insert into a caulking gun. For wall panelling and sheet flooring, apply 6mm beads along studs or joists in a zig-zag line at 40cm intervals. Bring surfaces together within 10 minutes and press firmly along glue lines. Reposition if needed within 20 minutes. Fix with nails, screws, or clamps for at least 24 hours to ensure bond strength. For contact bonding, apply to one surface, bring together, then separate for 3–5 minutes before rejoining. Clean tools and excess adhesive with mineral turpentine. Technical Information Coverage: Approximately 15 metres of 5mm bead Initial bond: Within 24 hours at 25°C Full cure: Up to 7 days Colour: Brown Important Notes Not suitable for mirrors, polystyrene foam, or continuous water immersion Avoid use on copper-based metals or metals exposed to direct sunlight heat Do not use for tightly clamped joints or heavy loads without mechanical fasteners Safety Information Use in a well-ventilated area and avoid breathing vapours Wear protective gloves and eye protection Keep away from heat, sparks, and open flames Keep out of reach of children If swallowed, do not induce vomiting — contact a doctor or Poisons Information Centre (AUST 131 126; NZ 0800 764 766) Contains 30% w/w liquid hydrocarbons
$4.85
Bastion Premixed Tile Adhesive 15 kg Overview Bastion Premixed Tile Adhesive 15 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$45.00
Dunlop Wall Tile Adhesive 15 kg OverviewDunlop Wall Tile Adhesive 15 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first.Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured.What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat.How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$79.61
Dunlop Floor Tile Adhesive 4kg is a premium cement-based adhesive formulated for fixing a wide range of floor tiles, including ceramic, porcelain, mosaics, and natural stone. It provides strong bonding performance, easy application, and long-lasting durability for both indoor and outdoor projects. Key Features Ideal for floor installations in residential and commercial settings Suitable for concrete, cement screeds, compressed fibre-cement sheets, and existing tiles Strong adhesion with excellent workability and pot life of up to 2.5 hours Can be used indoors and outdoors for versatile tiling applications Grey colour finish for consistent, professional results Coverage Recommended trowel: 10 x 10 x 10 mm Approximate coverage: 0.4 m² per kg Typical total coverage: around 1.6 m² per 4 kg bag Mixing Instructions Use approximately 400 ml of clean water per 1 kg of powder. Add powder to water and mix to a thick, creamy consistency. Allow to stand for 5 minutes, then re-mix thoroughly before use. Do not add additional water once mixed. Application Apply with a suitable notched trowel ensuring full coverage under tiles. Spread only enough adhesive that can be tiled within the open time. Press and slide tiles at right angles to the notches for full contact. Do not exceed a bed thickness of 10 mm or less than 3 mm. Allow adhesive to set for approximately 24 hours before grouting. Limitations Not suitable for continuous water immersion such as pools or tanks Do not use over timber floors or non-absorbent substrates like metal Not recommended for substrates subject to movement or shrinkage Additional Information Clean tools with water immediately after use Shelf life: up to 12 months when stored sealed in a dry location Full traffic after 24 hours at 23°C and 50% relative humidity 10 Year Guarantee: Backed by Ardex Australia Pty Ltd against manufacturing defects when used according to the manufacturer’s directions. Based on Dunlop official technical data sheet. Always follow the latest installation guidelines and safety instructions.
$28.90
Dunlop Trade Resaflex Rapidset Tile Adhesive 15kg is a high quality, fast setting, rubber modified cement-based adhesive designed for rapid installation and early grouting. It delivers strong adhesion on walls and floors and is suitable for interior applications and exterior areas with satisfactory drainage. Key benefits Ready to grout in about 3 hours at 23°C and 50% RH Rubber modified formulation for strong bond and improved workability Classified C1FES1 Suitable bed thickness from 1.5 mm up to 10 mm Wall and floor use, interior and exterior (with correct falls and drainage) Suitable tiles Ceramic, porcelain, vitrified and mosaics Non moisture sensitive stone Suitable substrates Render, plasterboard, fibre cement sheet walls Compressed fibre cement sheet floors, concrete floors Existing tiles for interior applications Mixing and use Water addition: 5.5 L to 6.0 L per 15 kg bag Pot life: about 40 minutes at 23°C and 50% RH Trowel guidance: 6 x 6 x 6 mm on walls to achieve about 1.5 mm bed. 10 x 10 x 10 mm on floors to achieve about 2.5 mm bed Back buttering recommended for deeply keyed tiles and tiles larger than 450 mm on any edge Grouting: typically after about 3 hours at 23°C and 50% RH Coverage guide Trowel size Approximate coverage 6 mm About 0.6 m² per kg (about 9 m² per 15 kg) 10 mm About 0.4 m² per kg (about 6 m² per 15 kg) Movement joints Include movement joints in line with AS 3958 and around perimeters, penetrations and changes in direction. Fill with a suitable flexible sealant. Clean up Clean tools and residue with water while the adhesive is wet. Limitations Not suitable for continuous immersion such as swimming pools Not for moisture sensitive or translucent stone Do not tile directly over timber floors Safety Wear gloves, eye and face protection. Avoid breathing dust. In case of contact with eyes, rinse with water and seek medical advice. Keep out of reach of children. Technical details are based on manufacturer guidance at standard conditions. Actual times and coverage vary with temperature, humidity, tile and substrate.
$56.95
Dunlop Pressure Sensitive Carpet Tile Adhesive 2L Dunlop Carpet Tile Adhesive is a high strength, water based pressure sensitive adhesive designed for carpet tiles and double bonded underlay systems. It tacks off to a clear, dry-to-touch film that grips firmly yet allows tiles to be lifted and replaced for maintenance. Key features Pressure sensitive grab for secure hold and easy tile replacement Water based, low odour, easy to apply Suitable for smooth or textured tile backings and composition vinyl tiles Works with double bonded underlays in commercial fitouts Suitable substrates Concrete, plywood, fibre cement sheet, compressed fibre cement, and suitable underlay sheets. Subfloors must be dry, smooth, clean, and prepared to AS 1884 requirements including moisture testing. Coverage Approx. 10 m² per 2 L using a 1.6 mm V notched trowel Approx. 14 m² per 2 L using a long nap roller Drying and traffic Allow adhesive to become tacky and transparent before laying tiles. Typical tack off time is 2 to 4 hours depending on conditions. Heavy foot traffic after 24 hours Avoid wet cleaning or water exposure for 48 hours Application guide Prepare the subfloor. Prime very porous substrates if required. Treat rising damp or green concrete with a suitable moisture barrier. Apply adhesive evenly: Textured backs, composition vinyl tiles, and double bond underlays: 1.6 mm V notched trowel held at about 60 degrees Smooth backed tiles: long nap roller Wait until the film is tacky and clear with no transfer to fingertips. Early placement into wet adhesive will create a more permanent bond. Lay tiles, cut and reposition as required, then roll in both directions with a suitable roller to ensure full contact. Clean up Clean tools immediately with warm soapy water. Remove dried residue with mineral turps. Storage and shelf life 12 months in unopened packaging when stored in a cool, dry place at about 23°C and 50% RH. Good to know Do not apply below 15°C or above 30°C surface temperature. Not suitable for traditional carpet-to-underlay stretch-in installations. For double bond systems, follow the flooring manufacturer’s instructions. Safety Wear gloves and eye protection, ensure adequate ventilation, and keep out of reach of children. If eye contact occurs, rinse with water and seek medical advice if irritation persists.
$38.56
Davco Ceramacrete Cement Base Tile Adhesive 5kg Davco Ceramacrete is a cement based tile adhesive for rigid substrates with patented Dust Less technology that reduces airborne dust during mixing. It offers good bond strength, tidy mixing and clean up, and can be used in thin or thick beds for efficient tiling results. Where to Use Interior and exterior walls and floors Bathrooms, showers, kitchens, laundries, living areas, balconies and patios Domestic and light duty commercial projects Tile Types Ceramic Mosaic Terracotta Slate Quarry tiles Not suitable for natural stone. Suitable Substrates Concrete Cement based screeds and renders Rendered block or brickwork For flexible framed substrates or submerged applications such as pools and spas, use with Davco Davelastic additive as directed. Key Features Dust Less formula for less mess and faster clean up Good bond strength Usable for thin bed and thick bed tiling Colour varies from white to grey Low VOC 5 g/L Mixing and Application Mixing ratio 1.25 L of clean cool water per 5 kg bag Allow to stand for 5 minutes after mixing, then remix before use Do not add extra water after initial mixing Working Times at 23°C and 50% RH Pot life 40 minutes Open time 7 minutes Adjustability time 15 minutes Ready for Use Grouting after 24 hours Return to dry area service after 24 hours Return to wet area service after 7 days Preparation Tips Ensure substrates are sound, clean, dry and free from contaminants Prime as required according to substrate condition and primer directions Install movement joints in line with good tiling practice Clean Up and Safety Clean tools with water before the adhesive dries Use appropriate personal protective equipment Refer to the product SDS for detailed safety advice
$10.30
You have seen 240 out of 508 products
Shop a wide range of bonding solutions for everyday fixes and demanding builds. From instant super glues to heavy‑duty construction adhesives and specialist formulas for plastic, metal, glass, and wood, find the right strength, set time, and finish for your job. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
