Power Through Soap Scum & Kill 99.9% of Germs Selleys Complete Clean Bathroom & Shower Spray is a household-grade disinfectant cleaner that cuts through tough soap scum, dirt and grime while killing 99.9% of common bathroom germs (S. aureus and E. coli). Ideal for showers, bathtubs and toilets for a sparkling clean finish. Disinfects effectively: Kills 99.9% of germs (S. aureus & E. coli). Fast soap scum removal: Powers through built-up residue on bathroom surfaces. Household-grade disinfectant: Designed for hard, non-porous bathroom surfaces. Where to Use Suitable for hard, non-porous surfaces such as: showers, bathtubs, toilets and similar bathroom fixtures. Not Suitable For Marble, natural stone, porous tiles or aluminium surfaces Polished, varnished or lacquered surfaces Skin (hard surface disinfectant only) Directions Turn nozzle to ON while directing trigger away from face. Spray directly onto the surface until fully covered. For cleaning: wipe with a clean damp cloth or rinse. For disinfecting: allow 10 minutes contact time, then wipe with a clean damp cloth. On food-contact areas: rinse or wipe with a clean damp cloth after 10 minutes. Good to Know Always test on an inconspicuous area first. Avoid prolonged contact with sensitive surfaces listed above. Keep out of reach of children. Read label before use. Product Details Brand: Selleys Range: Complete Clean Type: Bathroom & shower disinfectant spray Size: 750mL trigger spray
$5.79
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$37.95
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$25.48
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$22.35
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$44.00
Selleys Aquadhere Quick Set is a quick setting PVA wood glue that is suitable for all types of wood, sets twice as fast compared to normal PVAs and requires no clamping in many situations*. It will bond almost anything your craft work calls for! Features Fast bonding No clamping* Convenient and easy to use Non-toxic, water clean-up Dries clear *No need for clamping where joints are not under stress and timber is not bowed, warped etc Where can this product be used? School projects Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window frame Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Decorating What materials is this product suitable for? Interior wood Carboard Paper Fabric Felt Leather How to Use Surfaces to be bonded must be close fitting, dry and clean. Shake bottle and apply thinly to one surface. Press surfaces together firmly for 1-2 minutes. Wipe off excess adhesive with a damp cloth whilst still wet If joint is under stress or timber is bowed or warped, clamp until adhesive sets. Adhesive strength will be sufficient for object to be handled after 5-10 minutes for softwoods and 15-20 minutes for hardwoods. Allow 30-60 minutes before working with object. Maximum strength is attained in 4-8 hours. Allow longer setting/bonding time in cold or humid conditions. Limitations: Not for exterior use. Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere Quick Set is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Selleys Aquadhere exterior or Selleys Aquadhere Durabond). Will not take timber stains. Aquadhere Quick Set is not recommended for joints that are subjected to constant high stress. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Selleys Aquadhere Exterior.
$24.60
Bonds most materials within 30 seconds High-viscosity allows for greater accuracy and detail Large 100ml container Integrated nozzle for easy application Ritetite Control is a one-component gel super glue that bonds extremely quickly. It’s made with a specially designed thixotropic formula that instantly polymerises (hardens) by absorbing surface moisture. Its fast-curing properties make it an excellent choice for high-speed industrial applications that require a gel-like, viscous adhesive that does not spread or leak like traditional super glue. Ritetite Control works exceptionally well in poor-fitting applications such as rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber bonding due to its thick gel consistency. Surface Preparation prior to bonding with RITETITE CONTROL Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE CONTROL Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$54.39
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40 m2 Apply with: Lint free cloth Coats: 2 Recoat: 24 Hours Sheel Level: Pale Satin
$30.95
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$15.16
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$13.35
Prep Marathon Sugar Soap for Walls and Floors cleans dirt, grease, and grime from all types of flooring. Remove soap scum from showers with ease on mirror shower doors. The multi-use formula means one product can do more than just one job!
$4.28
Prep marathon is the ultimate metal big-wig in crevices and corners. A scrub that trims down, it gets into the nooks to clean while also protecting with a silicone shield. It’s tough on calcium, rust and scale deposits which makes it ideal for use on tiles, porcelain sinks bathrooms and showers or baths. Get Prep Marathon today!
$4.00
There's a lot of grime to be wary of in this world, and there's no reason you should have to put up with it. Prep marathon gets your day off on the right foot by getting your house clean as a whistle again. Reach out today for this hardworking citrus-based cleaner that intensively degreases stubborn messes and is tough enough to tackle kitchen grease spills with ease. And because we use non-petroleum solvers, our lotions are less drying than most brands while still being gentle on hands. Get Prep Marathon Re-Moove-It Cleaner now!
$6.00
Clean your outdoor glass surfaces consistently! Little clumps of dirt and debris can dirty your windows within moments. For easy, efficient, and quick clean-up have the Prep Marathon Outdoor Glass Click & Spray handy. It's formulated to easily dislodge tough dirt over time with innovative technology. The click feature is perfect for those who are unable to stand for extended periods of time.
$7.00
No one likes those big, ugly streaks on their favorite mirror--trust us. Make sure your streak-free shine is up to snuff with a bottle of Prep Marathon Glass Cleaner before you start sweating for that marathon! The product is PH balanced and has been laboratory tested. You deserve an honest cleaning every time you use it, which can be easily achieved with this top selling solution!
$4.78
Clean the glass and brighten your shower in one go. Prep Marathon Glass Cleaner is a tough enough cleaner to remove streaks from surfaces, but gentle enough for laminates, chrome or any other delicate surface. If you're looking for an easy way to start off every home clean on the right track, order Prep Marathon Glass Cleaner now!
$6.00
Directions: Well recognised as a cleaning agent, can be used undiluted but traditionally in a diluted form 50/50 with water Uses: General cleaning, glass services & safe on stainless steel. Also safe to use in food preparation areas
$9.47
Prep Marathon is the perfect product for anyone who hates dirtying their hands when cleaning. Our BBQ cleaner combines hunger and cleanliness with a fresh scent to leave your dishes shining like new. When it comes to cooking, this easy prep option is ideal for making sure all of popsicles have made it into mouths safely- but also neat enough to make your house feel like royalty after you're finished!
$4.00
Loctite Super Glue Longneck Bottle features a precision tip which allows controlled application without dripping, thus less mess. It has an easy-open cap with a metal pin that cleans and seals the nozzle for a clog-free performance. The long nozzle is ideal for gluing hard to reach surfaces. The ''finger friendly'' bottle keeps fingers glue free, as well as allows for a continuous flow or a precise drop of glue. It bonds a variety of materials including leather, ceramic, rubber, paper, metal, china, wood and most plastics. Loctite Super Glue Longneck Bottle dries clear and sets without clamping. Loctite Super Glue Longneck Bottle is resistant to moisture, most chemicals and freezing temperatures. Recommended For Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings Not Recommended For Use in dishwasher, oven or microwave Use on repairs needing high flexibility Glazed surfaces Exterior Applications Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene Safety Precautions Apply in a well-ventilated area. Wear gloves and wash hands after use. Preparation Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup Cured adhesive may be cut away with caution using a sharp blade, acetone or with boiling water.
$8.44
Loctite's versatile and reliable Super Glue Liquid is fast and strong and has a range of applicators that will get the job done quickly in every situation. It dries transparent to form a long-lasting invisible bond in seconds. Now with a NEW formula, resisting to all conditions: *Water and dishwashing *Shock *Temperatures from -50°C up to 120°C Recommended on: China, Porcelain, Metal, Rubber, Leather, Wood, Plastic (except PE/PP), Paper. Properties: Multi-use liquid superglue, ideal on non-porous surfaces Water and dishwasher resistant Shock resistant Temperature resistant (from -50°C up to 120°C) Bonds in seconds Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators - anti-spill / easy grip / long nozzle / brush-on Suitable for use on most surfaces* Solvent-free *Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$16.00
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T22 SCREWLOCK Low Strength for Easy Disassembly - 50ml Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance. Applications T22 is specifically formulated to lock and seal small screws (less than ¼), including set screws with long engagement lengths. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal results. If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow to fully cure before applying load. Properties of Uncured Material Chemical Type: Anaerobic Colour: Purple Toxicity: Low Solid Content: 100% Viscosity @ 25°C, cPs: 900-1,500 cps Specific Gravity: 1.05 Shelf Life: 24 months Performance of Cured Material Fixture Speed: 15-20 Min @ 22°C Full Cure: 24 Hours @ 22°C Temperature Range: -50°C to 150°C Product Conformity: MIL-S-46163A, ASTM D-5363, NSF Technical Datasheet The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm 9Nm on 3/8 plain steel nut & bolt after 1 hour and 5Nm 11Nm after 24 hours. On a 3/8 zinc nut & bolt, the strength is 1Nm 4Nm after 24 hours. Environmental and Fluid Resistance Heat Age: 100% retention in Engine oil @ 150°C Brake Fluid @ 150°C: 85% retention ATF @ 150°C: 85% retention 50/50 water/ethylene glycol @ 120°C: 80% retention Water @ 100°C: 80% retention Gasoline @ 25°C: 95% retention Diesel Fuel @ 25°C: 100% retention Ethyl Alcohol @ 25°C: 90% retention Active & Inactive Metal Table Category Cure Speed Metals Super Active Very Fast Cure Brass, Copper, Magnesium Active Fast Cure Iron, Steel, Nickel, Aluminium Inactive Slow Cure Stainless Steel, Titanium, Zinc Passive Primer Necessary Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes
$34.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$14.99
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$28.10
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$12.90
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$24.20
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White - Pack size: 225ml How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$6.50
Safer for the environment and still does the work. The EcoConcepts Graffiti Remover is a revolutionary development in the ongoing struggle to remove paint, ink, permanent marker and unwanted graffiti from a variety of surfaces. Unlike traditional graffiti removers, EcoConcepts is environmentally-friendly and much safer for the user. Suitable for removing paint, pen, sticky residues, grease, oil, crayon, lipstick and more. Made from renewable ingredients and readily biodegradable. Contains no carcinogens, phosphates, chlorine bleach or harsh solvents. EcoConcepts represents truly green cleaning. Diluted with water it can be used on plastic, laminate, metal, carpet, most painted surfaces and whiteboards. Undiluted it will penetrate and remove graffiti from porous surfaces such as brick, stone or concrete. I’m a concentrate and nearly ready for use. Use undiluted for the toughest jobs on porous and durable surfaces. Dilute for use on less stubborn stains and less durable surfaces. Always test on an inconspicuous area first. UNDILUTED For ultimate paint and stain removal, especially on unpainted surfaces such as concrete. HIGH DILUTION Generally safe on less durable and painted surfaces – 1 part product to 5 parts water, e.g. 167mL of product makes 1L of high-dilution solution. LOW DILUTION For tougher jobs on relatively durable surfaces – 1 part product to 3 parts water, e.g. 250mL of product makes 1L of low-dilution solution.
$42.54
An effective and easy-to-use neutral cleaner designed to remove general household dirt, grime, and oils from tiles and grout. Ideal for daily use, this cleaner is powerful enough to tackle grease in kitchens and bathrooms while being gentle enough for regular application. Key Benefits: Powerful cleaner for tiles and grout Effectively removes grease in kitchens and bathrooms Regular use reduces mould and mildew growth Suitable for general-purpose surface cleaning Cost-effective when diluted and applied by spray Easy to use for everyday cleaning Use On: Tiles, grout, and general household surfaces Surface Type: Walls and floors Location: Indoor and outdoor use Colour & Sizes: Size: 1L Item Code: 22504 Coverage: Wipe On: Dilute 10ml per 1L of water Spray On: Dilute 6ml per 1L of water Directions for Use: Test First: Before the first application of Dunlop Tile & Grout Cleaner, test a small amount of product in an inconspicuous area to ensure the desired result. Dilution: Mix 10mL of Dunlop Tile & Grout Cleaner per 1L of water. For best results, use hot water. Application: For general cleaning, apply the cleaner using a mop. For stubborn dirt, use an appropriate scourer or scrubbing pad that won't scratch the tile surface. Keep your tiles and grout clean and fresh with this powerful, easy-to-use cleaner, perfect for daily household maintenance.
$25.02
A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml
$20.03
Davco® Tile & Grout Cleaner is specially formulated to tackle tough dirt and stains from tiles and grout. It’s also effective in removing minor efflorescence, making it a versatile cleaner for common tiled surfaces. Key Benefits: Specially formulated ingredients Effectively cleans tiles and grout Removes minor efflorescence from grout Helps remove mould and mildew from grout surfaces Usage: Davco® Tile & Grout Cleaner is suitable for a wide range of tiled surfaces, including: Ceramic Porcelain Mosaic Quarry Slate tiles It’s ideal for removing tough dirt and stains from tiles, as well as refreshing aged grout. Packaging: Size: 1 Litre Jerry Can Colour: Clear liquid Application Steps: Mixing: Dilute Davco® Tile & Grout Cleaner with water in a clean plastic bucket at a ratio of 10 parts water to 1 part cleaner (e.g., 5L of water to 500ml of cleaner). Application: Prepare the Surface: Always wet the surface with clean water using a mop or sponge before applying the product. For Normal Cleaning: Dampen a mop or sponge with the diluted solution and wipe over the surface, then immediately rinse with clean warm water. For Heavily Soiled Areas: Apply a larger quantity of the solution and allow it to soak for up to 10 minutes. Scrub the affected area with a stiff nylon brush, then rinse thoroughly with clean warm water. Keep your tiles and grout clean, refreshed, and free from tough stains and minor efflorescence with Davco® Tile & Grout Cleaner.
$33.54
Davco® Sanitized Glue Grout A Pre-mixed, Ready-to-Use Wall Tile Adhesive and Grout Davco® Sanitized Glue Grout is a flexible, white, pre-mixed adhesive and grout for internal wall tile applications. Ideal for thin bed fixing of porous-backed ceramic tiles, it’s suitable for domestic areas like bathrooms, kitchens, and laundries. Key Features: White appearance Pre-mixed and ready for immediate use Dual-purpose: serves as both adhesive and grout Ideal for fixing lifted or popped tiles No wastage Usage: Surfaces: Cement renders Rendered brickwork and blockwork Plasterboard Fibre-cement wall sheets Tiles: Suitable for thin-bed fixing of most porous-backed ceramic tiles Areas: Interior applications, including domestic walls, bathrooms, kitchens, and laundries Advantages: Ready to use, no mixing required Suitable for adhesive and grout in one product Convenient for quick repairs or installations No product wastage Packaging & Colour: Packaging: 500g pail Colour: White paste Application Information: Adjustability Time: 20-30 minutes (depending on climate and substrate porosity) Ready for Use: 24 hours Note: Drying time may vary based on climate, substrate, and tile porosity. Coverage: A 500ml tub of Davco® Sanitized Glue Grout covers approximately 0.5m² when applied with a 6mm notched trowel as an adhesive. Application Steps: Surface Preparation: Ensure all surfaces are structurally sound, dry, clean, and free of contaminants like oil, grease, or loose material. Deeply contaminated surfaces should be abraded to expose at least 80% of the original substrate. Follow these preparation guidelines: Substrate Specific Requirement Primer Rendered brick/blockwork Cured minimum 7 days, sound Davco PrimeX or Ultraprime Fibre-cement sheet/plasterboard Correctly and firmly fixed Davco PrimeX or Ultraprime Previously painted surfaces Sand back to expose 80% of surface Davco PrimeX or Ultraprime Mixing: No mixing required. Davco® Sanitized Glue Grout is ready to use straight from the pail.
$24.79
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Orange]](http://gluesaustralia.com.au/cdn/shop/files/9314235_fada9554-ceb7-411e-9690-c908a0973b94.jpg?v=1754715678&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Orange]](http://gluesaustralia.com.au/cdn/shop/files/9314235_b6829499-6c70-4712-bf76-ae02aa34ac1d.jpg?v=1754715678&width=645)
$9.49
Apply to your arts, crafts, slime and school projects for a luminous glow. Expose to bright light for minimum 2 minutes. Switch off the lights and watch it glow. When glow fades, expose to light again.
$9.49
Non-Toxic Washable Extra Strength Safe for children Boyle PVA Glue is ideal to bond paper, wood, cork, ceramic, porcelain, fabrics, leather and much more.
$3.38
Quick Drying Ideal for most handicrafts Airtight Cap Boyle craft glue is ideal to use on paper, cardboard, wood, plastic, glass, ceramics, metal, fabrics, felt, yarns, beads, sequins, leather and much more.
$9.49
Quick Drying Ideal for most handicrafts Airtight Cap Boyle craft glue is ideal to use on paper, cardboard, wood, plastic, glass, ceramics, metal, fabrics, felt, yarns, beads, sequins, leather and much more.
$3.08
Non-toxic PVA glue that is non-staining and dries clear. Ideal for models, masks and other craftwork. Non-staining and specially developed to easily wash off clothes, hands and upholstery, even when dry! Made in Australia
$9.95
$22.78
$38.96
Betta TileCare Tile & Grout Sealer with Wheel Applicator is a premium, water-based penetrating sealer that forms an invisible moisture-repellent barrier. Ideal for use in bathrooms, kitchens, laundries, and other wet areas, it helps prevent water damage, stains, and mould growth on porous tiles and grout. The included wheel applicator makes sealing fast and easy, delivering smooth and precise coverage with minimal mess. Once cured, it dries clear without leaving a slippery or glossy finish, maintaining the natural look of your surfaces. Surface Preparation Ensure surfaces are clean, dry, and free of mould, soap scum, and any existing sealers or coatings. Remove silicone sealants prior to application. For best results, allow grout and tiles to dry for at least 24 hours before sealing. Heavily porous surfaces may require 3–4 days of drying time. Application Instructions Shake well before use. Starting from the top of the area, apply sealer evenly using the wheel applicator. Ensure all tile and grout lines are thoroughly coated. Allow to absorb for 15 minutes. Reapply a second coat if needed. Wipe away any excess product from tiles with a clean, dry cloth. Avoid heavy foot traffic or moisture exposure for at least 24 hours after final coat. Coverage Approx. 5–10m² per litre depending on tile and grout porosity. Drying Time Touch dry in 15 minutes Fully cured in 24 hours Clean-Up Clean tools and applicator with water immediately after use. Technical Data Appearance: Milky white (dries clear) Base: Water-based penetrating sealer Finish: Invisible, non-slip Application method: Wheel applicator Suitable for: Porous tiles and grout (indoor use)
$21.32
Betta TileCare Tile & Grout Cleaner is a powerful, ready-to-use solution designed to effectively remove ingrained dirt, grease, grime, and oil deposits from tiled surfaces without causing damage. Its fast-acting, biodegradable, and non-caustic formula makes it both user-friendly and environmentally responsible. Surface Preparation: Ensure the surface is free from dust and loose materials before cleaning. Application Instructions: Spray Betta TileCare Tile & Grout Cleaner directly onto the affected area. Vigorously scrub the area with a stiff brush to lift dirt and grime. For heavily soiled surfaces, repeat the application as necessary until the stain is removed. Coverage: Approximately 3 to 4 square meters per liter. Drying Time: Allow the cleaned area to dry completely before use. Cleanup: After scrubbing, leave the solution on the surface for 5 to 10 minutes, then rinse thoroughly with water. Do not allow the cleaner to fully dry before rinsing. Technical Data: Appearance: Clear liquid pH Level: Neutral Solubility: Fully water-soluble
$29.75
You have seen 142 out of 142 products
Bottled adhesives with precision tips for controlled dots and lines on crafts, woodworking and assembly. Match open time and clamp needs to your project; store upright to avoid leaks. Use filters to refine by chemistry, cure speed and temperature rating. Always review the product page and TDS/SDS.
