Professional Use

Show previous products

• 

  View options

  Dunlop Dunlop Premixed Mastic Tile Adhesive 20kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Premixed Mastic Tile Adhesive is a high performance, ready-to-use wall tile adhesive from Dunlop Trade (ARDEX Australia). Supplied in a convenient 20kg pail, there is no mixing, no mess and no guesswork – just open the lid and start trowelling. Its superior non-slump formulation holds even large format wall tiles and dimensional stone such as marble and granite firmly in place while you work, and its high flexibility and tenacity make it a favourite with tilers who want dependable grab straight off the trowel.Where to use itDesigned for indoor walls only. It is ideal for bathrooms, kitchens, laundries and splashbacks, and its unique formulation allows use in wet areas. Fix ceramic wall tiles, granite and marble (excluding moisture sensitive stone) over cement render, plasterboard, fibre-cement sheet, suitably prepared painted surfaces and Dunlop Waterproofing Membrane (porous tiles only).How to useEnsure surfaces are clean, dry and sound. Spread the adhesive with a suitable notched trowel, working in manageable sections, then press tiles firmly into the ribs with a slight twisting action. Adjust tiles within about 45 minutes of laying (at 23°C and 50% humidity). The adhesive dries in approximately 24 hours depending on temperature, and the porosity of the surface and tiles, after which grouting can proceed.Important notesDo not use over waterproofing membranes with dense or glazed tiles – use porous tiles only, as the adhesive will not dry properly between two non-absorbent layers. Not suitable for floors or exterior applications.Specifications Size 20kg pail Colour White Coverage Approx. 8-10m² per 20kg Tile types Ceramic wall tiles, granite, marble (not moisture sensitive stone) Substrates Render, plasterboard, FC sheet, painted surfaces, Dunlop membrane (porous tiles) Classification D2TE dispersion adhesive SafetyUse in a well-ventilated area and wear protective gloves and eye protection. Avoid skin and eye contact, wash hands after use and keep out of reach of children. Refer to the safety data sheet before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $99.60

  View options

• 

  View options

  Dunlop Dunlop Express Wet Area Tape 80mm x 10m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Express Wet Area Tape is a self-adhesive waterproofing joint tape that seals the most leak-prone parts of a wet area, the joints where floor meets wall, and around shower grates and outlets. Simply peel and stick: no messy fillets, no waiting for a bond breaker to cure. Paired with Dunlop Express Wet Area Waterproofing membrane it forms a rapid, complete waterproofing system that lets tiling commence just four hours after the membrane goes on.Where to use itSuitable for indoor and outdoor wet areas including bathrooms, showers, laundries and balconies. It performs over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard.How to useMake sure surfaces are clean, dry and dust-free. Peel the backing and press the tape firmly along floor/wall junctions, corners and around penetrations such as shower grates and outlets. Where two lengths of tape meet, overlap them by a minimum of 15mm. Then apply Dunlop Express Wet Area Waterproofing membrane over the taped joints and the rest of the area as normal.Important notesA standard shower recess with 1.8m high walls needs roughly 7m of tape, so one 10m roll comfortably covers a typical shower. Used with the Express membrane, the system meets Australian Building standards for wet area waterproofing.Specifications Size 80mm x 10m roll Colour Grey Overlap Minimum 15mm at joins Substrates AAC, fibre-cement, concrete, renders, screeds, wet area plasterboard SafetyLow-hazard adhesive tape; use care with cutting tools and follow the safety directions of the waterproofing membrane applied over it.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $65.28

  View options

• 

  View options

  Dunlop Dunlop Pro Rapid Tape 75mm x 15m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Pro Rapid Tape is a self-adhesive sealing tape that delivers an instant waterproof seal across the joints where leaks start: the junction between floor and wall, and around shower grates and outlets in bathrooms, kitchens and laundries. It is the joint-sealing half of the Dunlop Pro Rapid system; team it with Dunlop Pro Rapid Waterproofing Membrane and tiling can commence just four hours after the membrane is applied, with the finished system meeting Australian Building standards for waterproofing.Where to use itDesigned for internal wet areas such as bathrooms, showers, kitchens and laundries. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheets, wet area grade plasterboard, plywood, internal AAC blocks and panels, concrete cured for a minimum of 28 days, and renders and screeds cured for a minimum of 7 days.How to useEnsure the surface is clean, dry and free of dust. Peel the release liner and press the tape firmly into floor/wall junctions, corners and around grates and outlets, smoothing out air bubbles as you go. Then apply Dunlop Pro Rapid Waterproofing Membrane over the tape and the remainder of the area to complete the system.Important notesSubstrate curing times matter: concrete needs at least 28 days and renders or screeds at least 7 days before taping and waterproofing. This tape is intended for internal applications and is designed to work as a system with the Pro Rapid membrane.Specifications Size 75mm x 15m roll System partner Dunlop Pro Rapid Waterproofing Membrane Tile after 4 hours (as part of Pro Rapid system) SafetyLow-hazard self-adhesive product; take care when cutting lengths and follow the safety directions on the membrane used over it.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $98.41

  View options

• 

  View options

  Dunlop Dunlop Express Wet Area Waterproofing 1kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Express Wet Area Waterproofing is a high performance, water-based acrylic polyurethane membrane built for speed. Its high-build consistency lets you brush on a thick, even film that reaches the required membrane thickness with ease, and when used with Dunlop Express Wet Area Tape you can start tiling just four hours later. This handy 1kg tub is ideal for small repairs, patching and touch-up work, and it is backed by a 10 year guarantee.Where to use itUse indoors or outdoors in wet areas: showers, bathrooms, laundries and balconies. It adheres to AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard on walls and floors.How to usePrime the clean, dry substrate, seal junctions and penetrations with Dunlop Express Wet Area Tape, then brush on the first coat of membrane. Once dry, apply a second coat at right angles to the first until the required thickness is achieved. Tiling can commence after 4 hours when the full Express system is used. Wash brushes in water immediately after use.Important notesWaterproofing has minimum application requirements under AS3740: after two coats the dry film must be 1mm thick on floors and 0.5mm on walls. Check local council specifications before you begin. The membrane is a Class III membrane to AS/NZS4858.Specifications Size 1kg tub Coverage Up to 0.84m² on walls or 0.42m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyVentilate the area, wear gloves and eye protection, and avoid skin contact. Keep away from children and consult the Safety Data Sheet before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $43.00

  View options

• 

  View options

  Dunlop Dunlop Express Wet Area Waterproofing 20kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Express Wet Area Waterproofing in the 20kg pail is the full-bathroom format of Dunlop's fast-track membrane. This high performance, water-based acrylic polyurethane formula offers superior workability and a high-build film that reaches the required thickness without endless coats. Combined with Dunlop Express Wet Area Tape, the system lets tiling commence in as little as four hours, and it carries a 10 year guarantee.Where to use itMade for indoor and outdoor wet areas: showers, bathrooms, laundries and balconies. Apply it over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard, on walls and floors.How to usePrime the substrate with the appropriate Dunlop primer, seal all floor/wall junctions, corners and penetrations with Dunlop Express Wet Area Tape, then brush the membrane on generously. When the first coat is dry, brush on a second coat at right angles to the first to build the required film thickness. Tiling can begin after 4 hours when the complete Express system is used. Tools clean up in water while wet.Important notesAS3740 requires a minimum dry film thickness after two coats of 1mm on floors and 0.5mm on walls; confirm requirements with your local council. Certified as a Class III membrane to AS/NZS4858 and conforming to AS3740-2010 Wet Area Membranes.Specifications Size 20kg pail Coverage Up to 17m² on walls or 8.5m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyWork with good ventilation, wear gloves and safety glasses, and avoid contact with skin and eyes. Store sealed, away from children, and read the Safety Data Sheet first.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $313.95

  View options

• 

  View options

  Dunlop Dunlop Waterproofing Reinforcing Mat 100mm x 50m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Waterproofing Reinforcing Mat is the quiet workhorse of a Dunlop waterproofing job. This 100mm wide fabric roll is embedded into the wet membrane at every corner, joint and crack, the places where movement and stress are most likely to open up a leak. By carrying the membrane across these weak points, it helps guarantee proper film thickness in the critical zones and lets you apply the second waterproofing coat immediately over the reinforced areas.Where to use itUse it indoors in wet areas as an integral part of the Dunlop waterproofing system, together with Dunlop Undertile Waterproofing. Reinforce wall/floor junctions, wall/wall corners, sheet joints, cracks, shower hobs and hob/floor joints, over metal or PVC angles, and along 90-degree external edges such as balcony perimeters.How to useApply the first coat of membrane to the junction, press a length of mat into the wet membrane so it sits flat without air pockets, then coat over the top so the fabric is fully saturated. The mat also acts as a carrier in awkward, hard-to-reach spots and smooths rough joints so the membrane covers evenly. Cut lengths with scissors or a utility knife as you go.Important notesThe junctions between wall and floor, hob and floor, and vertical corners where two walls meet should always be reinforced. The mat is a reinforcing component, not a standalone waterproofing product; it must be fully encapsulated in membrane.Specifications Size 100mm x 50m roll Use with Dunlop Undertile Waterproofing and Dunlop membranes Application areas Junctions, corners, joints, cracks, hobs, edges SafetyLow-hazard fabric product; take care when cutting and follow the safety directions of the membrane being used. A Safety Data Sheet is available from Dunlop Trade.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $67.73

  View options

• 

  View options

  Dunlop Dunlop Rapid Bond Coat 1L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $67.73

  View options

• 

  View options

  Dunlop Dunlop Undertile Waterproofing 12.5kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Undertile Waterproofing is a hard-wearing, highly flexible liquid membrane that forms a seamless waterproof barrier beneath tiles. Brushed on straight from the pail, its ready-mixed blue formula makes it easy to see your coverage as you build the film, and once cured it protects the structure beneath showers, laundries and balconies from moisture damage for the long haul.Where to use itDesigned for indoor wet areas such as showers, bathrooms and laundries, as well as balconies. It bonds to AAC blocks, bricks, concrete, renders, screeds, fibre-cement sheet, marine plywood and wet area grade plasterboard on both walls and floors.How to usePrime the prepared surface with the appropriate Dunlop primer, then brush on the first coat of membrane, embedding Dunlop Reinforcing Mat into wall/floor junctions, corners, hobs and joints while it is wet. Once the first coat has dried, apply a second coat at right angles to the first to reach the required film thickness, then tile over it with a compatible Dunlop tile adhesive.Important notesAustralian Standard AS3740 sets minimum membrane thicknesses: after two coats, the dry film must be at least 1mm on floors and 0.5mm on walls. Check your local council requirements before starting. The membrane is certified to AS4858 and AS4654.Specifications Size 12.5kg pail Coverage Approx. 10m² on walls or 4.5m² on floors per pail Substrates AAC, brick, concrete, renders, screeds, fibre-cement, marine plywood, wet area plasterboard Colour Blue SafetyEnsure good ventilation, wear gloves and safety glasses, and avoid skin and eye contact. Keep the pail sealed and stored away from children. Read the Safety Data Sheet before application.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $142.94

  View options

• 

  View options

  Dunlop Dunlop Multipurpose Primer 4L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Multipurpose Primer in the 4 litre pack is the job-sized version of Dunlop's water-based bonding primer, made for whole-room and whole-house preparation work. It improves the bond between the substrate and Dunlop floor levellers, renders, tile adhesives and waterproofing membranes, turning dusty, porous surfaces into a reliable base. It suits new and old concrete, particleboard and compressed fibre-cement sheets alike.Where to use itUse indoors or outdoors, on walls and floors. It is at home on fibre-cement sheeting, concrete slabs, masonry and lightweight concrete blocks, particleboard, renders and screeds, before levelling, rendering, tiling or waterproofing with Dunlop systems.How to usePrepare the surface so it is clean, dry and free of dust, grease and loose material. Pour out the primer and spread an even coat with a brush or roller, working it into the surface. Let it dry clear before applying the next product in your system. Wash tools in water immediately after use.Important notesOn very porous substrates a second coat is required to achieve a continuous primed film. The white-on, clear-dry formula shows exactly where you have coated. Actual coverage depends on substrate porosity and site conditions.Specifications Size 4 litres Coverage Approx. 6m² per litre (up to approx. 24m² per pack) Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyWear gloves and eye protection, keep the work area ventilated, and avoid prolonged skin contact. Keep away from children and refer to the Safety Data Sheet before starting.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $60.26

  View options

• 

  View options

  Dunlop Dunlop Multipurpose Primer 1L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Multipurpose Primer is a water-based primer engineered to strengthen the bond between a substrate and the Dunlop product applied over it. It is the go-to preparation step for flooring work, priming ahead of floor levellers, renders, tile adhesives and waterproofing membranes, and it performs equally well on new or old concrete, particleboard and compressed fibre-cement sheeting.Where to use itApproved for indoor and outdoor use on both walls and floors. Typical substrates include fibre-cement sheets, concrete, masonry and lightweight concrete blocks, particleboard, renders and screeds. Prime before levelling a slab, rendering a wall, waterproofing a bathroom or laying tiles.How to useSweep or vacuum the surface so it is clean, sound and free of dust, oil and curing compounds. Apply an even coat by brush or roller and allow it to dry clear before applying your leveller, render, adhesive or membrane. Because it is water-based, brushes and rollers wash out in water straight after use.Important notesVery porous substrates will drink in the first coat, so a second coat is required to build a proper film. The primer applies white and dries clear, making coverage easy to track. Coverage figures are a guide only and vary with surface condition.Specifications Size 1 litre Coverage Approx. 6m² per litre Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyKeep off skin and out of eyes, wear gloves, and ensure good ventilation while working. Store sealed and away from children. Consult the Safety Data Sheet for full handling guidance.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $34.59

  View options

• 

  View options

  Dunlop Dunlop Primer & Additive 1L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Primer & Additive is a ready-to-use liquid primer that boosts the grip between your substrate and the Dunlop products that go on top of it. Whether you are about to level a floor, lay tiles or roll out a waterproofing membrane, a quick coat of this milky-white liquid seals porous surfaces and gives adhesives, levellers and membranes a far stronger key to bond to. It doubles as a grout additive, improving flexibility, adhesion, colour depth and resistance to abrasion and staining.Where to use itSuitable for both indoor and outdoor projects, on walls and floors. Use it over concrete, cement sheet, fibre-cement, plasterboard, sheeting and timber before applying Dunlop tile adhesives, floor preparation products or waterproofing membranes.How to useMake sure the surface is clean, dry and free of dust or contaminants. Apply undiluted before waterproofing, tiling and timber floor preparation; dilute it for priming wall board. On large floor areas a household broom works well to spread the primer and push it into the surface. Allow it to dry clear before continuing with your adhesive, leveller or membrane. Tools rinse out in water while the product is still wet.Important notesCoverage varies with the porosity of the substrate. The primer goes on white and dries clear, so you can easily see where you have already coated. Highly porous surfaces may need extra material.Specifications Size 1 litre bottle Coverage Approx. 4m² per litre undiluted; approx. 8m² per litre diluted Substrates Concrete, cement sheet, fibre-cement, plasterboard, timber Colour Applies white, dries clear SafetyWork in a ventilated area, avoid contact with skin and eyes, and keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $29.50

  View options

• 

  View options

  Dunlop Dunlop Ardit Feather Finish 8kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications Size 8kg bag Coverage Approx. 27m² over concrete or 55m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $125.51

  View options

• 

  View options

  Dunlop Dunlop Ardit Floor Leveller 20kg

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Dunlop Ardit Floor Leveller is a premium cement-based levelling compound built on the renowned Ardit Technology from ARDEX. It offers superior flow and workability, spreading easily across uneven concrete to create a smooth, even surface before new floor coverings go down. Floors are walkable in around 3 hours and ready for ceramic tiles in the same timeframe, keeping renovation and re-flooring jobs moving quickly.Where to use itUse indoors and outdoors under covered areas over sound concrete floors, ahead of ceramic tiles, carpet or vinyl. It is designed for concrete substrates only and must be protected by a floor covering rather than left exposed to the weather or used as a finished wear surface.How to useEnsure the slab is clean, sound and primed as required. Mix each 20kg bag with approximately 4.5L of clean water using a low-speed paddle mixer until smooth and lump free. Pour and spread with a trowel, letting the compound flow out and level itself. Apply from a thin skim up to 25mm in one pass, adding 2-5mm aggregate for deeper fills.Important notesNot suitable for driveways or areas subject to vehicular traffic. Vinyl and carpet can be laid after about 24 hours, while tiles can go down after roughly 3 hours. Refer to the technical datasheet for priming guidance on porous slabs.Specifications Size 20kg bag Coverage Approx. 12m² at 1mm or 4m² at 3mm per bag Thickness 1-25mm per application Substrates Concrete Walk-on time 3 hours (tiles 3 hours; vinyl and carpet 24 hours) SafetyContains cement, which is alkaline when wet. Wear gloves, eye protection and a P2 dust mask while mixing, ensure good ventilation, avoid skin contact and rinse promptly if the mix touches skin or eyes. Store away from children.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $67.45

  View options

• 

  View options

  Loxeal Loxeal Metalox Metal Repair Epoxy Kit 10 x 25ml Bi-Syringes

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal Metalox Metal Repair Epoxy Kit 10 x 25ml Bi-Syringes Loxeal Metalox is a solvent-free, fast-curing, metal-filled two-part epoxy engineered for repairing and bonding metal components. This trade pack contains 10 x 25ml bi-syringes, each supplied with mixing nozzles, so every job starts with fresh, accurately proportioned adhesive. Its thixotropic (non-sag) paste works as an adhesive filler – rebuilding metal castings, pipework and flanges – and once cured it can be machined, sanded and painted, typically within a few hours of application. Why choose Loxeal Metalox? Trade pack of 10 x 25ml bi-syringes with mixers – fresh 1:1 dispensing on every repair Fast cure – handling strength in around 15 minutes, sandable in about 5 hours at room temperature Strong on steel – lap shear strength of 21 N/mm² on grit-blasted mild steel Machinable, sandable and paintable after polymerisation, even for outdoor repairs Non-sag thixotropic paste stays put on vertical and overhead surfaces Excellent resistance to water and many chemical agents Heat cure option: 1 hour at +60°C speeds cure and boosts final strength Typical applications Repairing metal castings, pipework and flanges Automotive body repair and panel filling Bonding metal substrates, plus concrete, wood and other rigid materials Maintenance and plant repairs where downtime must be kept short How to use Scratch or abrade the surface, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the bi-syringe and discard the first 3–5 cm of extruded product. Apply the mixed adhesive directly to the repair area; work at temperatures above +15°C. Assemble or shape immediately and leave undisturbed until cured. Once cured (sandable after about 5 hours at +25°C), machine, sand or paint as required. Cure times Pot life: approximately 5 minutes at +25°C Handling strength: approximately 15 minutes Sandable: about 5 hours at +25°C (90% of final hardness) Accelerated cure: 1 hour at +60°C for full resistance sooner Specifications Chemistry Two-part epoxy (resin / amine hardener), metal-filled Colour Part A metallic grey / Part B black Mixing ratio 1:1 by volume Pot life (+25°C) Approx. 5 minutes Handling strength Approx. 15 minutes Lap shear strength (ISO 4587) 21 N/mm² (grit-blasted mild steel); 18 N/mm² (stainless steel) Compression strength (ASTM D695) 60 N/mm² Hardness (ISO 868) Shore D 65 Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Shelf life 24 months unopened at +5°C to +25°C Important notes Apply at temperatures above +15°C; higher temperatures and large mixed quantities reduce pot life Avoid mixing excess product – the curing reaction generates heat Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Wear suitable gloves, avoid skin and eye contact, and work in a well-ventilated area. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $385.95

  View options

• 

  View options

  Loxeal Loxeal 34-59T Structural Acrylic Adhesive Transparent Gel 150ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Important: this adhesive needs a companion to cure, and works best with: A Loxeal structural acrylic activator (Activator 20), applied to the mating surface. This is a no-mix, two-part system and will not cure without the activator. Not currently stocked online, please contact us to order it. Loxeal Cleaner 10 Degreaser: clean and degrease both surfaces first, as grease and water prevent adhesion. Loxeal 34-59T Structural Acrylic Adhesive Transparent Gel 150ml Loxeal 34-59T is the transparent gel version of Loxeal's 34-59 series – a fast-curing, chemically activated structural acrylic adhesive used together with a Loxeal Activator (such as Activator 20). No mixing is required: apply the adhesive to one surface and the activator to the other, press the parts together and the joint fixtures in as little as 20–40 seconds. The toughened, thixotropic gel is non-sag on vertical surfaces, bonds ferrites, metals and ceramics, and delivers a wide service temperature range up to +165°C. Supplied in a 150ml pack. Why choose Loxeal 34-59T? Transparent gel formulation for tidy, discreet bond lines No mixing required – cures on contact with the matching Loxeal Activator Very fast fixturing – typical handling time 20–40 seconds High strength – shear strength 20–30 N/mm² with strong impact resistance High temperature capability – service range -65°C to +165°C Non-sag gel suits vertical and overhead application Acid-free chemistry, ideal for high-speed assembly lines Typical applications Structural bonding of ferrites, metals and ceramics (e.g. magnet bonding in motors and speakers) High-speed production and assembly line joining Bonded joints exposed to elevated temperatures, impact and vibration How to use Clean both surfaces with Loxeal Cleaner 10 and allow to dry – water and grease prevent adhesion. Apply the Loxeal Activator to one surface and the adhesive gel to the other. Assemble and press the parts together until handling strength is achieved (20–40 seconds). For gaps larger than 0.5 mm, apply activator to both surfaces before applying the adhesive to one side. Remove excess uncured adhesive with an organic solvent and allow at least 24 hours for full cure before loading the joint. Cure times Handling time (with Activator 20): 20–40 seconds Functional cure: 10–20 minutes Full cure: 24 hours Specifications Chemistry Urethane methacrylate structural acrylic (chemically activated, no-mix) Form Transparent thixotropic gel Viscosity (+25°C) 15,000–25,000 mPa·s (thixotropic) Gap filling 0.05–0.20 mm (activator on both faces for larger gaps) Shear strength (ISO 4587) 20–30 N/mm² Tensile strength (ISO 6922) 20–25 N/mm² Impact strength (ASTM D950) 15–25 kJ/m² Service temperature -65°C to +165°C Pack size 150ml Shelf life 1 year unopened at +25°C Important notes Requires a Loxeal Activator (e.g. Activator 20), applied to the opposing surface – sold separately Not designed for polyolefins (PP/PE), PTFE or soft, flexible materials Store in a cool, dry place away from direct light, at no more than +25°C Specifications shown are for the Loxeal 34-59 series adhesive Safety Consult the Safety Data Sheet (SDS) before use. Avoid skin and eye contact and ensure good ventilation during application. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $139.00

  View options

• View options

  Loxeal Loxeal Superlox Polyolefin Bonder Kit 10 x 25ml Bi-Syringes

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: clean and degrease the plastics first for a stronger bond (no primer required). Loxeal Superlox Polyolefin Bonder Kit 10 x 25ml Bi-Syringes Loxeal Superlox is a two-part acrylic adhesive developed to bond polyolefins – polypropylene (PP), polyethylene (PE), HDPE and LDPE – and other notoriously difficult low-surface-energy plastics, without primers, flame treatment or other expensive surface pre-treatments. This trade pack contains 10 x 25ml bi-syringes, each with mixing nozzles, dispensing the two components at a simple 1:1 ratio. It joins polyolefins to each other and to other plastics such as ABS and PVC, and to metals, producing structural joints with high shear and peel strength. Why choose Loxeal Superlox? Bonds the "unbondable" – PP, PE, HDPE and LDPE plus other low-surface-energy plastics No primer or surface pre-treatment required – clean, apply, assemble Trade pack of 10 x 25ml bi-syringes with mixers – fresh adhesive for every job Simple 1:1 mixing ratio through the supplied static mixing nozzles Structural performance – high shear and peel strength on plastics and mixed-material joints Also bonds polyolefins to other plastics (ABS, PVC) and to metals Typical applications Repairing and fabricating PP and PE components: tanks, housings, containers, piping and trim Joining polyolefin parts to dissimilar plastics or metal brackets and fittings Manufacturing and maintenance work on low-surface-energy plastic assemblies How to use Clean the surfaces to remove dust, oil and grease (for example with Loxeal Cleaner 10) and allow to dry. Fit the static mixing nozzle to the bi-syringe and discard the first few centimetres of extruded adhesive. Apply the mixed adhesive to one surface. Assemble the parts promptly and hold or clamp them without movement while the adhesive sets. Leave the joint undisturbed until fully cured before applying load. Cure times Fast curing at room temperature – parts typically fixture within minutes of assembly Allow 24 hours for full strength before placing joints under working load Refer to the Technical Data Sheet for precise fixture and cure data for your conditions Specifications Chemistry Two-part structural acrylic, polyolefin bonder Mixing ratio 1:1 by volume via static mixing nozzle Key substrates PP, PE, HDPE, LDPE and other low-surface-energy plastics; also ABS, PVC and metals Surface preparation No primer or pre-treatment required – clean and dry surfaces only Strength profile High shear and peel strength Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Important notes Work at room temperature; low temperatures slow the cure Use each mixing nozzle for one continuous application – fit a fresh nozzle if work is interrupted Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and avoid skin and eye contact. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $495.95

  View options

• View options

  Loxeal Loxeal Cleaner 10 Degreaser 1L Tin

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  The recommended surface prep for Loxeal adhesives and sealants: Use before threadlockers, retaining compounds, gasketing, epoxies, structural acrylics and instant adhesives for maximum bond strength. Often paired with Activator 11 for anaerobics or Activator 9 for super glues. Loxeal Cleaner 10 Degreaser 1L Tin Loxeal Cleaner 10 is a non-CFC, solvent-based cleaner and degreaser formulated for preparing surfaces before bonding or sealing with adhesives and sealants. Great adhesion starts with a clean joint: Cleaner 10 lifts oil, grease and contamination, evaporates completely in around 60 seconds and is non-corrosive, leaving surfaces perfectly ready for adhesive. Importantly, it has no effect on the cure speed or final strength of Loxeal adhesives and sealants. This 1 litre tin is the economical choice for busy workshops and production benches. Why choose Loxeal Cleaner 10? Purpose-made for surface prep before threadlockers, retainers, epoxies, acrylics and instant adhesives Fast flash-off – dries in about 60 seconds at room temperature Non-corrosive and residue-free on metals Does not interfere with adhesive cure speed or bond strength Economical 1 litre tin for decanting or wipe application Non-CFC solvent formulation Typical applications Degreasing machined, treated or coated surfaces before bonding or sealing Cleaning oil- and grease-contaminated parts in maintenance and assembly work Preparing plastic substrates prior to adhesive application (check compatibility first) How to use Apply Cleaner 10 generously to the surfaces to be bonded. While the surface is still wet, wipe with a clean cloth to lift heavy contamination. Allow the solvent to evaporate until the surface is completely dry (about 60 seconds). Apply the adhesive or sealant immediately after drying and assemble the joint. Specifications Formulation Non-CFC solvent blend Appearance Colourless liquid Boiling range +92°C to +102°C Flash point (COC/DIN/ISO 2592) -1°C (highly flammable) Density (+25°C, DIN 51757) 0.70 g/ml Drying time (+25°C) Approx. 60 seconds Water solubility Not soluble Corrosivity None Pack size 1 litre tin Shelf life 12 months at +5°C to +25°C Important notes The solvent can affect certain plastics and coatings – check compatibility on a hidden area first Unclean or partially cleaned surfaces can significantly reduce adhesive performance Do not return used product to the original container Store between +5°C and +25°C in a cool, dry place Safety Consult the Safety Data Sheet (SDS) before use. Highly flammable: keep away from naked flames and non-flameproof electrical equipment, use only in well-ventilated areas, avoid prolonged or repeated skin contact and do not smoke near the product. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $79.95

  View options

• 

  View options

  Loxeal Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 100g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 100g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. This 100g workshop bottle is the economical choice for production lines, maintenance teams and busy workshops that go through super glue regularly. Why choose Loxeal Istant 23? Trade-size 100g bottle – keeps high-use workshops and production benches running Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Solvent-free, single part – clear cure with tensile strength of 12–25 N/mm² Typical applications Production assembly and repetitive bonding tasks O-rings, seals and neoprene/NBR rubber components Maintenance and repair across rubber, metal and plastic parts Workshops and trades that need a reliable everyday instant adhesive in volume How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 100g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $135.00

  View options

• 

  View options

  Loxeal Loxeal Istant 25 Super Glue Medium Viscosity Cyanoacrylate Adhesive 20g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 25 Super Glue Medium Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 25 is a medium-to-high viscosity super glue based on ethyl cyanoacrylate, designed for bonding plastic, rubber, metal and ceramic – including slightly irregular surfaces where a runny glue would simply drain away. At 350–450 mPa·s it stays where you put it, fills gaps up to 150 microns and fixtures in seconds, with a medium setting speed that gives you a moment to position parts. Supplied in a 20g bottle. Why choose Loxeal Istant 25? Medium viscosity – controllable application that stays put on the joint Handles imperfect surfaces – fills gaps of 10–150 microns Broad substrate range – plastic, rubber, metal and ceramic with one product Fast, strong fixture – tensile strength of 15–23 N/mm² when cured Solvent-free, single part – clean, clear bond line with no mixing Typical applications Repairs on ceramics, ornaments and household items Bonding rubber and plastic parts with less-than-perfect mating surfaces Metal-to-plastic and metal-to-rubber assemblies General workshop, trade and hobby bonding How to use Clean and degrease both surfaces and allow them to dry fully. Apply a modest bead or drops to one surface only. Assemble the parts promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; phenolic resin 5–20 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 350–450 mPa·s (medium) Gap fill 10–150 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 15–23 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $24.95

  View options

• 

  View options

  Loxeal Loxeal Istant 43 Speciale Super Glue Cyanoacrylate Adhesive 50g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 43 Speciale Super Glue Cyanoacrylate Adhesive 50g Loxeal Istant 43 Speciale (43S) is a surface-insensitive, general purpose super glue based on modified ethyl cyanoacrylate. Unfazed by acidic and porous surfaces, it excels at bonding leather, wood, fabric, ceramic and metals where ordinary super glues struggle. It offers proven heat resistance to +120°C (short peaks to +150°C) and is NSF registered for use in and around food processing areas, making it a favourite for demanding trade and industrial work. Supplied in a 50g bottle. Why choose Loxeal Istant 43 Speciale? Surface insensitive – cures reliably on acidic and porous substrates like leather, wood and paper Heat resistant – holds strength up to +120°C, with short-term peaks to +150°C NSF registered – acceptable for use as an instant adhesive in and around food processing areas Very fast on hard-to-glue materials – fabric in 2–20 seconds, leather in 5–15 seconds Strong all-rounder – medium viscosity with tensile strength of 15–25 N/mm² Typical applications Leather goods, footwear and upholstery repairs Woodworking, trim and joinery fixes across many timber species Equipment maintenance around commercial kitchens and food processing plants Fabric, ceramic, metal and rubber bonding in workshops and on site How to use Clean and degrease all surfaces and allow them to dry before applying the adhesive. For low-energy plastics such as PE, PP or PTFE, apply Loxeal Primer 7 first and let it dry. Apply the adhesive sparingly to one surface, then bring the parts together quickly and correctly aligned – the fast cure leaves little room for repositioning. Press firmly for a few seconds until fixed, and keep parts clamped until fully set. Wait 24–72 hours for full cure before applying any mechanical stress. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: paper 1–5 seconds; fabric 2–20 seconds; PVC, ABS and phenolic resin 2–10 seconds; aluminium 2–10 seconds; steel 5–20 seconds; leather 5–15 seconds; ceramic 5–30 seconds; softwoods 5–20 seconds; oak 90–180 seconds. Loxeal Activator 9 can be used to accelerate slow joints. Full cure in 24–72 hours. Specifications Chemistry Modified ethyl cyanoacrylate Colour Clear Viscosity (+25°C) 80–150 mPa·s (medium) Gap fill 10–150 microns Fixture time 1–180 seconds, substrate dependent Full cure 24–72 hours Tensile strength 15–25 N/mm² (ISO 6922) Service temperature -50°C to +120°C (peaks to +150°C) Approvals NSF registered for food processing areas Shelf life 12 months in original unopened packaging Pack size 50g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Not approved for use with pure or gaseous oxygen. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $57.95

  View options

• 

  View options

  Loxeal Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 20g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 20g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. Supplied in a 20g bottle that suits both the workbench and the kitchen drawer. Why choose Loxeal Istant 23? Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Clear, strong bond line – colourless cure with tensile strength of 12–25 N/mm² Solvent-free, single part – no mixing, no clamping hardware, straight from the bottle Typical applications Everyday repairs across rubber, metal and plastic parts O-rings, seals and neoprene/NBR rubber components Small component assembly in production and maintenance work Household and hobby fixes where a fast, tidy bond is needed How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $24.95

  View options

• 

  View options

  Loxeal Loxeal Istant 27 Super Glue High Viscosity Cyanoacrylate Adhesive 20g

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 27 Super Glue High Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 27 is a high viscosity, gap-filling super glue based on ethyl cyanoacrylate, made for irregular surfaces on plastic, rubber, metal and ceramic. Its thick 1,200–1,800 mPa·s consistency bridges gaps up to 200 microns without running, and its deliberately slower fixture time lets you adjust and align parts during assembly before the bond locks in. Supplied in a 20g bottle. Why choose Loxeal Istant 27? High viscosity, gap-filling formula – fills gaps of 10–200 microns on uneven surfaces Stays where applied – thick consistency will not run out of the joint or drip Repositioning window – slower fixture allows parts to be adjusted during assembly Strong final bond – tensile strength of 18–25 N/mm² when cured Solvent-free, single part – clear cure straight from the bottle Typical applications Bonding rough, porous or poorly matched surfaces Plastic and rubber parts with irregular mating faces Ceramic repairs where a runnier glue would soak away or drip Assemblies that need a few extra seconds of alignment time How to use Clean and degrease both surfaces and allow them to dry fully. Apply a bead of adhesive to one surface only. Assemble the parts, adjust alignment while the slower fixture time allows, then hold with light pressure. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; phenolic resin 10–40 seconds; aluminium 10–30 seconds; ABS 15–40 seconds; PVC 20–50 seconds; steel 20–50 seconds; zinc 40–100 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 1,200–1,800 mPa·s (high) Gap fill 10–200 microns Fixture time 5–100 seconds, substrate dependent Tensile strength 18–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $28.95

  View options

• 

  View options

  Loxeal Loxeal Activator 9 Cyanoacrylate Accelerator Spray 200ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Designed to be used with Loxeal super glues: Speeds the cure of Istant 23 Fluid, Istant 25 Medium, Istant 27 High Viscosity and Istant 43 Speciale. Loxeal Activator 9 Cyanoacrylate Accelerator Spray 200ml Loxeal Activator 9 is an accelerator spray for cyanoacrylate super glues that cleans and degreases parts while slashing setting times. Sprayed onto one surface before assembly, it triggers cure in just 1–4 seconds – even on slow, dry or hard-to-activate substrates – and a treated surface stays active for up to 8 hours. It can also be misted over squeezed-out adhesive after assembly to fix the excess instantly. Supplied as a 200ml aerosol for fast, even coverage. Why choose Loxeal Activator 9? Cure in 1–4 seconds – turns slow joints into instant ones Cleans as it works – degreases parts in the same step 8-hour activation window – pre-treat parts ahead of assembly Fixes surplus glue – instantly sets excess adhesive outside the joint Convenient aerosol – quick, even application on parts of any shape Typical applications Speeding up cyanoacrylate cure on wood, porous and acidic surfaces Production assembly where consistent, rapid fixture times matter Cold or low-humidity conditions where super glue sets slowly Instantly curing glue fillets and squeeze-out for a tidy finish How to use Spray a light coat of Activator 9 onto one of the surfaces to be bonded. Allow it to dry for 20–30 seconds. Apply cyanoacrylate adhesive to the other surface and assemble the parts – cure takes effect in 1–4 seconds. To set surplus adhesive after assembly, mist it lightly with Activator 9. Usage notes Exact curing effect depends on the adhesive type, gap between parts and surface composition. Treated surfaces remain active for around 8 hours, so parts can be prepared in advance. Note that heavy over-application of activator can reduce ultimate bond strength on some joints. Specifications Chemistry Organic chemicals in solvent composition Appearance Colourless Viscosity (+25°C) 1–2 mPa·s Drying time (+25°C) 20–30 seconds Cure effect 1–4 seconds, adhesive and gap dependent Activation life on surface 8 hours Shelf life 12 months in original unopened packaging Pack size 200ml aerosol spray Important notes Solvent based aerosol – use in a well-ventilated area away from heat and ignition sources. Store in a cool, dry place below +20°C and do not refill containers with used product. Pair with Loxeal Istant cyanoacrylate adhesives for best results. Safety Consult the Safety Data Sheet (SDS) before use. Pressurised container – protect from sunlight and do not expose to temperatures exceeding +50°C. This information is provided as a general guide only. Always test on your specific materials and refer to the manufacturer's technical documentation before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $69.95

  View options

• 

  View options

  Loxeal Loxeal 58-31 Gasketing Elastic Anaerobic Adhesive 75ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-31 Gasketing Elastic Anaerobic Adhesive 75ml Loxeal 58-31 is a high-performance anaerobic gasketing adhesive that cures to an elastic, flexible film, replacing solid pre-formed gaskets on flange joints. It seals against gases, water, LPG, fuels, oils and a wide range of chemicals, resists shocks and vibration, and keeps sealing from -55°C right up to +180°C. The thixotropic consistency stops the sealant migrating before or during cure, and the red adhesive fluoresces under blue light for easy inspection on the production line. Why choose Loxeal 58-31? Elastic cured film accommodates joint movement while maintaining the seal Higher strength and faster fixture than general-purpose flange sealants Extended service temperature to +180°C Thixotropic — no running or migration on vertical flanges Fluorescent under blue light for quality-control checks Dismantles with standard tools when service is required Typical applications Sealing flange joints on pumps, gearboxes and differential housings where an elastic, vibration-resistant gasket and elevated temperature capability are needed — demanding automotive, transport and industrial maintenance work. How to use Clean and degrease the flange faces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Assemble the parts and hold them in place while curing. Use Loxeal Activator 11 for faster cure on passive metals or at low temperatures. To dismantle, use normal tools (heat to +150°C/+250°C if necessary), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 10–20 minutes, functional strength in 1–3 hours and full cure in 6–12 hours. Cure speed varies with gap, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 70–600 Pa·s Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Breakaway torque (ISO 10964) 15–25 N·m Prevailing torque (ISO 10964) 18–28 N·m Shear strength (ISO 4587) 8–13 N/mm² Tensile strength (ISO 6922) 7–10 N/mm² Impact strength (ASTM D-950) 4–7 kJ/m² Service temperature -55°C to +180°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Fully cured Loxeal 58-31 offers excellent resistance to motor oil and gearbox oil at +125°C through 1,000 hours, excellent-to-good resistance to hot 50% water/glycol mixtures, and moderate resistance to gasoline on prolonged exposure. Important notes Recommended for metal surfaces — seek technical advice before applying to non-metal parts. Uncured adhesive can damage coatings, some plastics and elastomers, and may cause delayed stress-cracking in certain thermoplastics. Store cool and dry at no more than +25°C; do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $85.95

  View options

• 

  View options

  Loxeal Loxeal 58-14 Gasketing Anaerobic Adhesive 75ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-14 Gasketing Anaerobic Adhesive 75ml Loxeal 58-14 is a medium-strength anaerobic gasketing adhesive that forms a flexible in-place gasket between flange faces, doing away with pre-cut solid gaskets. The highly thixotropic formula stays exactly where it is applied without migrating before or during cure, and the cured film seals dependably against gases, water, LPG, fuels, oils and many other chemicals across a service range of -55°C to +150°C. Why choose Loxeal 58-14? One liquid gasket replaces an inventory of pre-formed paper, cork and plastic gaskets Flexible cured film shrugs off shocks and vibration Thixotropic — stays put on vertical and horizontal flanges Fills gaps up to 0.50 mm and compensates for minor surface imperfections Assemblies can be dismantled later with standard workshop tools Typical applications Gasketing and sealing of flange joints on pumps, gearboxes, differential housings and similar close-fitting metal assemblies in automotive workshops, plant maintenance and general engineering. How to use Clean and degrease both flange faces (Loxeal Cleaner 10 recommended). Apply a continuous bead so the joint gap is completely filled. Assemble the parts and hold them in position while the adhesive cures. On passive metals or in cold conditions, accelerate the cure with Loxeal Activator 11. To dismantle, use normal tools (heating the parts to +150°C/+250°C helps if needed), remove cured residue mechanically and clean up with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in around 24 hours. Cure speed varies with gap size, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Orange Viscosity (+25°C) 28,000–100,000 mPa·s, highly thixotropic Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 5–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +150°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Once fully cured, Loxeal 58-14 shows excellent resistance to motor oil and gearbox oil at +125°C out to 1,000 hours, and good long-term resistance to gasoline and to 50% water/glycol mixtures at +87°C. Important notes Formulated for metal surfaces — contact a technical adviser before use on non-metal parts. The liquid adhesive can attack coatings, some plastics and elastomers, and may induce delayed stress-cracking in certain thermoplastics. Store in a cool, dry place at no more than +25°C and never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use and follow standard workshop hygiene practices. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $67.95

  View options

• 

  View options

  Loxeal Loxeal 59-10 Gasketing High Temperature Anaerobic Adhesive 75ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 59-10 Gasketing High Temperature Anaerobic Adhesive 75ml Loxeal 59-10 is a single-component, medium-strength anaerobic flange sealant with outstanding heat resistance up to +200°C. It cures at room temperature when confined without air between close-fitting metal surfaces, forming a durable in-place gasket that replaces pre-formed gaskets, allows wider machining tolerances and still permits dismantling with normal tools. The cured seal is highly resistant to vibration, heat, water, gases, LPG, oils, fuels and many chemicals. Why choose Loxeal 59-10? Service temperature from -55°C to +200°C — ideal for hot-running assemblies Replaces pre-formed gaskets and assures true metal-to-metal contact Fills gaps up to 0.50 mm, accommodating greater machining tolerances Highly resistant to vibration, oils, hydrocarbons and coolants Parts remain serviceable — dismantle with everyday workshop tools Typical applications Sealing flat, rigid flange joints on pumps, gearboxes, camshaft blocks and motor flanges — anywhere a heat-tolerant, vibration-proof formed-in-place gasket is required. How to use Clean and degrease the mating surfaces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Bring the parts together and leave undisturbed until cured. On passivated surfaces or at low temperature, use Loxeal Activator 11 to speed the cure. For disassembly, use normal tools (heat to +150°C/+250°C if needed), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in 6–12 hours. Cure speed depends on substrate, gap and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red Viscosity (+25°C) 50–300 Pa·s Specific gravity (+25°C) Approx. 1.05 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 6–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +200°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance After full cure, Loxeal 59-10 maintains excellent resistance to motor oil and gearbox oil at +125°C and to 50% water/glycol coolant at +87°C through 1,000 hours; resistance to gasoline is excellent initially, reducing with prolonged immersion. Important notes Recommended for metal surfaces — seek technical advice before use on non-metal parts. Liquid product may damage coated parts and elastomers, and contact with some thermoplastics can induce stress-cracking that is not immediately visible. Store in a cool, dry place at +25°C or below; never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $66.95

  View options

• 

  View options

  Loxeal Loxeal 30-20 UV-Curable Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Loxeal 30-20 UV-Curable Adhesive 50ml Loxeal 30-20 is a fast-curing, high-strength UV adhesive purpose-made for glass and crystal bonding. Under a suitable UV lamp it sets in as little as 6–10 seconds, and its water-clear finish with over 98% light transmittance makes joints all but invisible — the go-to choice for decorative tableware, household and furnishing accessories, giftware and fine crystal work. Why choose Loxeal 30-20? Cures in seconds under UV light (365 nm) — parts are handled almost immediately Exceptional optical clarity: clear, colourless, non-yellowing joints High bond strength on glass-to-glass and glass-to-metal assemblies Bridges bond lines from 0.03 mm up to 1.5 mm Convenient one-part product — no mixing, cures only where the light reaches Typical applications Bonding glass and crystal in decorative tableware, homewares, furnishing accessories, bonbonnières and gift articles; ideal for precious crystal pieces where the joint must stay invisible. How to use Ensure both parts are clean and completely dry. Apply a small amount of adhesive to one surface and bring the parts together. At least one part must be UV-transparent — align the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Allow slightly longer exposure for larger gaps or tinted substrates. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Actual cure time depends on lamp intensity, distance from the light source, bond-line gap and how much UV passes through the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 2,200–2,900 mPa·s Specific gravity 1.1 g/ml Gap fill 0.03–1.5 mm Tensile strength (ASTM D-2095-69) 10–14 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Cured Loxeal 30-20 shows excellent long-term resistance to alcohol and refrigerant gases and good resistance to gasoline. Sustained exposure to high humidity (90% RH at +40°C) reduces bond performance, so it is best suited to dry indoor service. Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering glass — extend exposure accordingly. Not recommended for permanently damp or wet environments. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $115.95

  View options

• 

  View options

  Loxeal Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $55.95

  View options

• 

  View options

  Loxeal Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $60.95

  View options

• 

  View options

  Loxeal Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $57.95

  View options

• 

  View options

  Loxeal Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Medium Strength Anaerobic Threadlocker Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts and bolts of all types that may need to be dismantled later. It tolerates minor oil contamination on parts, so it performs even on as-received fasteners, and it holds its locking and sealing properties from -55°C to +200°C (up to +250°C for short periods). The direct alternative to Loctite 243. Why choose Loxeal 55-03 Oil tolerant: cures reliably on lightly oiled threads without extensive cleaning. High temperature: proven unscrewing resistance at +200°C. Serviceable strength: locks firmly against vibration yet can be dismantled with hand tools. Wide chemical compatibility: resists water, gas, oils, gasoline, brake fluid, ethanol, biodiesel and many chemicals. Blue colour, fluorescent under blue light for easy inspection. Certified and approved Gas: approved as gas-tight sealant for threaded fittings to EN 751-1 (DVGW and Gaz de France). Potable water: WRAS approved and compliant with the German UBA declaration for drinking water use. Food areas: NSF registered category S4 for use as an adhesive in and around food processing areas. Typical applications Locking machine bolts, pump housings, gearbox fasteners and automotive nuts and bolts subject to vibration. Threaded fittings in gas and potable water systems where certified products are required. Maintenance work on equipment where fasteners arrive lightly oiled. How to use Clean and degrease parts where practical (Loxeal Cleaner 10 recommended); minor oil films are tolerated. Apply enough product to completely fill the engaged threads. Assemble the parts and hold for the curing time. On passive surfaces or in cold conditions, Loxeal Activator 11 speeds curing (may slightly reduce final strength). Cure times at +25°C Handling: 10 to 20 minutes Functional: 1 to 3 hours Full cure: 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Strength grade Medium (dismantlable) Viscosity at +25°C 1,700 to 9,000 mPa·s, thixotropic Specific gravity Approx. 1.07 g/ml Friction coefficient Approx. 0.10 Max thread / gap filling M36 / 0.25 mm Shear strength 9 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 23 N·m (ISO 10964) Prevailing torque 9 to 16 N·m (ISO 10964) Service temperature -55°C to +200°C (+250°C short term) Approvals EN 751-1 (DVGW, Gaz de France), WRAS, UBA, NSF S4 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel at room temperature; excellent to good resistance to gasoline, brake fluid and 50 percent water glycol. Important notes For metal fasteners. Liquid product can damage coatings, some plastics and elastomers; stress cracking may develop with some thermoplastics. Not approved for pure oxygen or oxygen-rich systems, and not suitable as a sealant for chlorine or other strong oxidising agents. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. For professional and industrial use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $62.95

  View options

• 

  View options

  Loxeal Loxeal 24-18 Threadlocker Low Strength Anaerobic Adhesive 50ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 24-18 Low Strength Anaerobic Threadlocker Loxeal 24-18 is a low strength anaerobic threadlocker for nuts, bolts and screws of all types that need to be easily dismantled later with ordinary hand tools. It locks fasteners against loosening from vibration and thermal cycling while staying serviceable, making it the go-to grade for small screws, adjustment fasteners and parts that see regular maintenance. Why choose Loxeal 24-18 Easy disassembly: low breakaway torque means fasteners come apart with standard tools, no heat needed in most cases. Anti-vibration: prevents self-loosening caused by vibration, shock and temperature changes. Wide chemical compatibility: resists water, gases, oils, gasoline, diesel and many chemicals. Gas approved: DVGW approved as a gas-tight sealant for threaded fittings to European norm EN 751-1. Service temperature from -55°C to +150°C. Purple colour, fluorescent under blue light for easy inspection. Typical applications Locking small screws, grub screws, calibration and adjustment fasteners that require frequent servicing. General automotive, machinery and DIY threadlocking where easy removal matters. Thread sealing of metal fittings where a low strength, dismantlable seal is acceptable. How to use Clean and degrease threads (Loxeal Cleaner 10 recommended). Apply enough product to fill the engaged threads. Assemble the parts and tighten as normal. Allow to cure before putting into service. On passivated surfaces or in cold conditions, use Loxeal Activator 11 to speed curing. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Full cure: up to 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate Colour Purple (fluorescent under blue light) Strength grade Low (easy to dismantle) Viscosity at +25°C 800 to 1,400 mPa·s Specific gravity Approx. 1.05 g/ml Max thread / gap filling M24 / 0.20 mm Shear strength 3 to 5 N/mm² (ISO 10123) Breakaway torque 5 to 8 N·m (ISO 10964) Prevailing torque 2 to 5 N·m (ISO 10964) Service temperature -55°C to +150°C Approvals DVGW gas-tight sealant, EN 751-1 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent resistance to gasoline and brake fluid at room temperature; excellent to good resistance to motor oil, gearbox oil and diesel at +125°C, and to 50 percent water glycol at +87°C. Important notes For metal fasteners. Liquid product can attack some coatings, plastics and elastomers; contact with some thermoplastics may cause stress cracking. Pre-test if unsure. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $63.95

  View options

• Last stock!

  View options

  Prep Productions Prep Plastermate Stud Adhesive For Plasterboard To Timber And Steel Studs 5.2kg (Acrylic)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 5.2kg pail is the trade size for lining whole rooms.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the pail, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the pail label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the pail label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 5.2kg pail Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyThe paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $33.20

  View options

• Last stock!

  View options

  Prep Productions Prep Plastermate Stud Adhesive For Plasterboard To Timber And Steel Studs 1kg (Acrylic)

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Plastermate Stud Adhesive is a pre-mixed, trade-quality wallboard adhesive for fixing plasterboard sheets to wall and ceiling framing. Part of the Plastermate plastering range that Prep Productions has manufactured in Sydney for over 25 years, it is used by professional plasterers and DIY renovators alike. The smooth, non-slump paste holds its dab shape, which matters most when you are working overhead on ceilings, and it grabs strongly to both timber and steel studs. It complies with Australian Standard AS 2753, the standard for wallboard adhesives. The 1kg tub suits patch jobs and small lining work.Formula overviewA thick, water-based acrylic paste: an acrylic copolymer binder loaded with fine mineral filler gives it very high viscosity, so dabs stay exactly where you put them without slumping or stringing. It is light blue in colour, ready to use straight from the tub, and non-flammable.Where to use itIndoor: bonding plasterboard to timber studs and metal or steel studs for wall and ceiling linings.Outdoor: not intended for exterior use or wet areas unless the board manufacturer's system specifies otherwise. Check the tub label before using on substrates other than timber or steel framing.How to use Make sure framing is clean, dry and free of dust or oil. Apply walnut-sized dabs of adhesive to the stud face, spaced per the plasterboard manufacturer's specification for the sheet and frame type. Press the sheet into position and fix with screws or nails as the lining system requires. Refer to the tub label for open time and cure guidance. Wash tools and hands in warm soapy water before the adhesive dries. Important notes Dab size and spacing should follow the plasterboard system you are installing; the adhesive complements, not replaces, mechanical fixings. Store in a cool place out of direct sunlight with the lid sealed. Dried residue is combustible even though the wet paste is not; let spills harden and dispose of them per local regulations. Specifications Size 1kg tub Type Water-based acrylic stud adhesive Colour Light blue Consistency Thick non-slump paste Substrates Plasterboard to timber and steel studs Standard AS 2753 Clean up Warm soapy water Made in Australia SafetyThe paste is non-flammable. It may mildly irritate eyes, and repeated or prolonged skin contact can cause irritation, so wear safety glasses (especially when fixing ceilings) and rubber gloves, and work with adequate ventilation. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $17.90

  View options

• Last stock!

  View options

  Prep Productions Prep Organoil Woodguard Penetrating New Timber Seasoner And Sealer 4L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Organoil Woodguard is a deeply penetrating oil treatment made to look after brand-new exterior timber in the period between installation and final finishing. Fresh hardwood often carries high moisture and, left bare, can cup, split, crack or bleed tannins as it dries out. Woodguard soaks into the boards and stabilises them while they acclimatise, so the timber arrives at oiling day in sound, even condition. It is made in Australia by Prep Productions and formulated for harsh Australian and New Zealand exposure.Formula overviewA natural-oil blend built around tung oil and beeswax, carried by dipentene, a citrus-derived solvent. Rather than forming a film on top of the wood, the blend penetrates the timber surface, which is why it is applied as a single coat and later over-coated with a finishing oil.Where to use itOutdoor: new, raw timber decking, joists, bearers, cladding, posts, rails and exterior joinery. Particularly recommended for dense or high-moisture hardwoods such as spotted gum and plantation species before they are oiled.Indoor: not intended for interior finishing. Woodguard is an exterior pre-treatment, not a furniture or floor finish.How to use Stir well before use, as natural oils can settle. New raw timber can be treated directly. Timber that has already weathered in the elements should first be cleaned with a timber wash such as Organoil Wash-A-Way. Apply one coat only, using a brush or lambswool applicator. Coverage is up to 12 square metres per coat depending on timber density and porosity. Allow the treatment to dry fully before applying your finishing oil. Follow the can label for drying guidance. Important notes Woodguard is an interim protectant, not a final finish. Plan to apply a decking or exterior timber oil afterwards. Designed as a one-coat application. Do not over-apply. For new or raw untreated timber only. Previously coated timber should be stripped and washed first. Specifications Size 4 litres Base Solvent-borne natural oils (tung oil, beeswax, citrus-derived dipentene) Coats 1 Coverage Up to 12 m² per coat Finish Matt, natural Application Brush or lambswool applicator Made in Australia SafetyCombustible liquid (flash point around 61°C). Keep away from heat, sparks and open flames, and store below 30°C in a tightly closed container in a well-ventilated area. Rags and applicators soaked in this product can self-heat and spontaneously combust: lay used rags flat to dry outdoors or soak them in water before disposal. May irritate skin and eyes and can cause an allergic skin reaction in sensitised people, so wear gloves and eye protection. Refer to the Safety Data Sheet (SDS) for full details.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $84.56

  View options

• Sale -21%

  View options

  Glitz Glitz Spray On Wipe Off Multi Surface Cleaner 5L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml Glitz Spray On Wipe Off is your quick daily cleaner for busy kitchens, bathrooms, and high touch areas. Just spray, wipe, and you are done. It cuts through everyday grease, food splatter, soap scum, and dust to leave surfaces fresh and streak free. Why you will love it Fast spray and wipe action for daily clean ups Lifts light grease, grime, and sticky residues Streak free finish on most hard household surfaces Fresh clean scent that does not linger Ready to use 750ml trigger bottle for easy coverage Ideal for Benchtops and splashbacks Stainless steel appliances and rangehood exteriors Cooktops when cool, microwaves, fridges, and pantry shelves Bathroom vanities, taps, tiles, and shower glass Tables, desks, cabinet doors, light switches, and door handles Not recommended for Unsealed or waxed surfaces Natural stone such as marble, limestone, or travertine Untreated wood, leather, or fabrics Plasma or non glass coated display screens How to use Turn nozzle to the ON position. Spray directly onto the surface from about 20 cm away. Wipe with a clean damp cloth or paper towel. For stuck on grime, leave for 30 to 60 seconds before wiping. Buff with a dry cloth for a clear finish. Return nozzle to OFF after use. Pro tips Always test on an inconspicuous spot first. For food preparation areas, wipe with a clean damp cloth after cleaning. Use a microfiber cloth for best streak control on glass and stainless steel. Product details Brand Glitz Product type Everyday spray cleaner Format Ready to use Fragrance Fresh clean Bottle size 750 ml Surface compatibility Most sealed hard surfaces including laminate, ceramic, porcelain, stainless steel, glass, and finished wood What is in the box 1 x Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml with trigger Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other chemicals. FAQs Can I use it on stone benchtops Use only on sealed engineered stone. For natural stone like marble or limestone, use a stone specific cleaner. Does it leave residue It is designed to wipe clean. For food areas, finish with a damp cloth to remove any remaining cleaner. Is it suitable for glass Yes for quick touch ups. For crystal clear windows, follow with a dry microfiber buff. Good to know Great for daily resets after cooking and bath time Trigger head lets you choose between stream and spray patterns Pairs well with microfiber cloths and paper towels

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $33.11 $26.17

  View options

• Sale -6%

  View options

  Glitz Glitz Sugar Soap for Floors Heavy Duty Cleaner 750ml

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Glitz Sugar Soap for Floors Heavy Duty Cleaner Power through ground-in dirt, grease, and everyday grime with Glitz Sugar Soap for Floors. This heavy duty formula lifts stubborn residues and leaves floors fresh, streak free, and ready for living. Ideal for high traffic areas in homes, workshops, and commercial spaces. Why you will love it Heavy duty clean that cuts through grease, scuff marks, and sticky spills Low foam for a streak free finish on most sealed floors Fast acting formula reduces scrubbing time Residue free so finishes and sealers look their best Fresh, low odour for comfortable indoor use Best for these surfaces Use on most sealed and washable floors, including: Ceramic and porcelain tiles Vinyl and hybrid floors Laminate and sealed timber Sealed concrete and epoxy coated floors Do not use on unsealed timber, unsealed cork, natural stone that is unsealed, or waxed finishes. Always test in a small inconspicuous area first. How to use Sweep or vacuum to remove dust and grit. Dilute in warm water: General cleaning: 1 capful per 5 L bucket Heavy duty cleaning: 2 to 3 capfuls per 5 L bucket Apply with a mop or sponge. Work in sections. For stubborn spots, apply a little solution directly, wait 2 to 3 minutes, then gently agitate. Rinse mop frequently in clean water. Allow floor to dry before walking. Pro tips Change the bucket water when it turns cloudy to avoid streaks. Use heavy duty dilution before repainting or resealing floors to remove grease and prep the surface. For gloss finishes, wring the mop well to prevent pooling. Product details Brand Glitz Product type Sugar soap floor cleaner Format Liquid concentrate Appearance Clear to light solution, low foam Suitable surfaces Most sealed hard floors Clean up Rinse tools and mops in clean water Storage Keep tightly closed in a cool, dry place Safety Wear gloves if you have sensitive skin. Avoid contact with eyes. If splashed, rinse with water. Keep out of reach of children and pets. FAQs Do I need to rinse after cleaning Rinsing is generally not required on sealed floors when diluted as directed. If using heavy duty strength, a light rinse with clean water can help achieve a streak free finish. Can I use it in a spray mop Yes. Pre dilute following the general cleaning ratio and avoid over wetting the floor. Good to know Compatible with most microfiber and cotton mops Great prep step before resealing or repainting floors Helps remove oily residues that make floors feel slippery

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $5.27 $4.94

  View options

• Sale -7%

  View options

  Glitz Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25L is your everyday helper for a fast, streak free clean. Spray, wipe, and enjoy a bright finish on benches, tables, appliances, and other sealed surfaces around the home. Why you will love it Cuts through daily grime and light grease with ease Leaves a streak free shine on most sealed surfaces Fresh, clean household scent that does not linger No rinsing required on lightly soiled areas Ready to use for quick jobs or dilute for larger areas to save cost Best for Kitchen benches, tables, cupboards, splashbacks Bathroom vanities, tiles, taps, glass shower screens outside surface only Door handles, light switches, appliances exterior, bins Floors when diluted in a bucket for general freshen ups Do not use on Unsealed or waxed timber Natural stone that is unsealed or acid sensitive such as marble and limestone Screen displays or electronics Delicate finishes. Always spot test in a hidden area first How to use Light cleaning. Spray directly onto the surface and wipe with a clean cloth Heavier soil. Let sit for 30 to 60 seconds then wipe. Repeat if required Floors. Add 60 to 100 ml per 5 L of warm water, mop, then allow to dry Glass and glossy areas. Use a lint free cloth and buff dry for best results Quick tips Use separate cloths for kitchen and bathroom to avoid cross contamination For stainless steel, always wipe with the grain and finish with a dry cloth On painted surfaces, apply to cloth first, not directly to the wall Specifications Brand Glitz Product Domestic Cleaner Multi Purpose Surface Shine Format Ready to use liquid. Dilutable for floors Pack size 1.25 L bottle Fragrance Fresh household scent Surface compatibility Most sealed hard surfaces including laminates, sealed stone, ceramic tile, porcelain, stainless steel, enamel, and sealed timber Country of use Suitable for Australian homes and water conditions What is in the box 1 x Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25 L Storage and safety Store upright in a cool, dry place away from direct sunlight Keep out of reach of children and pets Avoid contact with eyes. If in eyes rinse with water Do not ingest. If swallowed seek medical advice Frequently asked questions Can I use it on food contact areas Yes. Clean the surface, then wipe with a damp cloth and allow to dry before food preparation Will it leave residue No when used as directed. Buff with a dry cloth on glass or glossy areas for a crystal finish Is rinsing required Not for light soil. For heavy soil or floors, rinse the mop head regularly for best results Good to know Ideal for quick daily resets in kitchens and bathrooms Economical size that suits family households and shared spaces

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $6.51 $6.04

  View options

• Sale -24%

  View options

  Glitz Glitz Pine Disinfectant Commercial Grade Sanitiser 5L

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Glitz Pine Disinfectant Commercial Grade Sanitiser 5L Refresh and sanitise high traffic areas with the classic clean of pine. Glitz Pine Disinfectant is a commercial grade cleaner that cuts through everyday grime, removes unpleasant odours, and leaves a crisp pine aroma. Ideal for homes, workplaces, schools, gyms, and hospitality areas where a fast, reliable clean is needed. Why you will love it Commercial grade performance for large and small areas Deodorises while it cleans with a fresh pine scent Versatile on sealed floors, benches, walls, bathrooms, and bins Low effort mop and wipe application Economical 5L size suited to frequent use and refill stations Where it works Sealed hard floors including tiles, vinyl, sealed concrete, and sealed timber Bathrooms, toilets, showers, and change rooms Kitchen and lunchroom benches, splashbacks, and cupboards Door handles, railings, desks, and other high touch points Bins and pet areas surfaces only, avoid direct contact with food How to use Always test on a small inconspicuous area first. Do not use on unsealed or porous stone. Avoid prolonged contact with natural marble and other acid sensitive surfaces. Application Dilution guide Directions General mopping and daily clean 1:80 to 1:100 (50 to 100 mL per 8 L bucket) Add to warm water, mop the surface, then allow to air dry. No rinse required on lightly soiled, non food contact areas. Bathrooms and heavy soil 1:10 to 1:20 Apply with sponge or cloth, scrub if needed, allow contact for 5 minutes, then rinse with clean water. Spray and wipe 1:20 in a trigger bottle Spray onto surface, wipe with a clean microfibre cloth, and let dry. Rinse food contact surfaces with potable water. Deodorising bins and drains Neat or 1:5 Rinse the area first, apply, allow contact time, then rinse away. Pro tips Use separate colour coded cloths and mops for bathrooms and kitchens to reduce cross contamination. For streak free floors, wring the mop well and change the solution when it becomes visibly dirty. Store the concentrate upright with the cap sealed to preserve freshness. Product details Brand Glitz Product type Pine disinfectant and sanitising cleaner Fragrance Pine Form Liquid concentrate Container size 5 litres Suitable surfaces Sealed hard floors, tiles, vinyl, sealed concrete, bathrooms, benches, walls Do not use on Unsealed stone, natural marble, unfinished timber, fabrics, or screens Safety and handling Read label before use. Keep out of reach of children. Use in well ventilated areas. Avoid breathing spray. Refer to the Safety Data Sheet (SDS) for full details. Frequently asked questions Can I use this on food contact surfaces Yes, but after cleaning you must rinse those surfaces with potable water. Will it leave a sticky residue When used at the recommended dilutions and allowed to dry, it leaves a fresh, clean finish without tackiness. Is it pet friendly Allow surfaces to dry completely before pets return. Do not allow pets to ingest the solution. Good to pair with Microfibre cloths for streak free wipe downs Colour coded mop heads and buckets for hygiene zones Trigger spray bottles for quick touch up cleans

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $27.62 $20.89

  View options

• Sale -15%

  View options

  Wagner Wagner Mask-It Masking Tape for Clean Paint Edges

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Get crisp, professional paint lines with Wagner Mask-It. This painter’s masking tape is designed to seal neatly along the edge, reduce paint bleed, and remove cleanly when the job is done. Ideal for walls, trim, skirting boards, window frames, and any detail work where a sharp finish matters. Key Benefits Clean paint edges that help minimise bleed on most interior surfaces. Easy application with a smooth unwind and hand tearable backing. Clean removal when used as directed on properly prepared surfaces. Works with brushes, rollers, and spray for DIY and trade jobs. Perfect For Cutting in around ceilings, cornices, and trims Protecting hardware, switches, and fittings Two tone feature walls and accent colours Masking glass, tiles, and metal fixtures during repainting Surface Compatibility Use on properly prepared, fully cured interior paint, primed timber, metal, glass, and most smooth surfaces. Always test in an inconspicuous area first. How To Use Prep the surface: Ensure it is dry, dust free, and fully cured. Apply the tape: Press down firmly along the edge with a putty knife or fingernail to seal. Paint: Roll or brush away from the tape edge for best results. Remove: Peel back slowly at a 45 degree angle while paint is still slightly tacky, unless your coating specifies otherwise. Pro Tips Burnish the tape edge lightly to improve the seal on textured areas. Apply light coats near the edge. Heavy wet coats can overwhelm any mask. For long runs, overlap tape pieces by a few millimetres and press the overlap firmly. Good To Know Suitable for indoor projects and general decorating. Store in a cool, dry place away from direct sunlight to maintain performance. Available in popular widths to suit trim work and broad masking. Frequently Asked Questions Will it pull off fresh paint?Only apply to fully cured paint. Cure times vary by product and conditions. When in doubt, allow extra time and test first. Does it work on lightly textured walls?Yes, on many light textures, but press down firmly along the edge and use lighter coats near the tape line. Can I use it with spray equipment?Yes. Apply, seal the edge, and use controlled passes. Avoid flooding the tape line.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $14.80 $12.65

  View options

• Sale -27%

  View options

  Bear Bear Black PVC Duct Tape for Fast Sealing and Repairs 48mm x 30m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Bear PVC Duct Tape is a tough, reliable, all purpose tape that delivers a strong hold and a clean finish for quick fixes. Ideal for sealing, bundling, patching, and general repairs at home, on site, and in the workshop. Its PVC backing resists moisture and abrasion, while the high tack adhesive bonds to a wide range of surfaces for dependable results. Why you will love it Fast grab for instant hold on contact Durable PVC backing resists scuffs, tears, and everyday wear Moisture resistant for confident indoor and short term outdoor use Conformable backing wraps neatly around pipes, ducts, and irregular shapes Easy to tear by hand for quick application without tools Low residue when removed from most clean surfaces Great for Sealing HVAC duct joins and flexible ducting Temporary patching of plastic sheeting, tarps, and covers Bundling cables, mats, and lightweight components Edge protection on cartons and packing jobs Quick fixes on site and around the home Works on Metal, plastic, vinyl, painted surfaces, cardboard, glass, masonry, timber, and more. For best results, surfaces should be clean, dry, and free of dust or oils. How to use Prepare the surface by cleaning off dust, grease, and moisture. Measure and tear the required length. Scissors are optional. Apply the tape with firm pressure, smoothing from the center outward to remove air pockets. Reinforce high stress areas with overlapping strips as needed. Pro tips Apply at room temperature for the best initial tack. On porous or rough surfaces, use extra pressure or a primer for maximum bond. For long term outdoor exposure, consider overcoating edges to limit water ingress. Typical specifications Backing PVC Adhesive Rubber based Total thickness Approx. 0.16 to 0.20 mm Temperature range Approx. −10 °C to +60 °C Finish Matte PVC Common sizes 48 mm width, 30 m length and other widths as available Colour Silver or Black depending on variant Values above are typical for PVC duct tapes and may vary by batch and width. FAQs Can I use it outdoorsYes for short term jobs. For permanent outdoor sealing, select a tape rated for UV and long term weather exposure. Will it remove cleanlyOn smooth, sealed surfaces it often removes with minimal residue. Always test on an inconspicuous area first. Is it suitable for high heatPVC duct tape is best within the stated temperature range. For sustained high temperature applications, choose a foil or specialty HVAC tape. Why buy from Glues Australia Trusted Australian supplier with fast dispatch Helpful support if you need sizing or product advice

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $12.68 $9.27

  View options

• Sale -19%

  View options

  Uni-Pro UNi-PRO Pre Taped Masking Film for Quick Painting Prep 550mm x 25m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Speed up your painting prep with UNi-PRO Pre Taped Masking Film. This convenient roll combines quality painter’s tape with a static-cling masking film that drapes cleanly and stays put, helping you protect trims, skirting, windows, and furniture while you cut in and roll. Perfect for quick room refreshes, touch ups, and full repaints. Why you'll love it Two in one tape and film for fast, tidy masking Static cling helps the film hug surfaces and reduce paint bleed Clean removal on most surfaces when applied to sound, cured paint 550 mm drop ideal for architraves, skirting boards, window frames, and small appliances 25 m length gives generous coverage for multiple areas Suitable for brushes and rollers with water based and most solvent based paints Best for Trims, doors, window frames, skirting boards Protecting benchtops, splashbacks, and appliances during repainting Quick masking on rentals and maintenance jobs How to use Ensure the surface is dry, dust free, and fully cured. Apply the taped edge along the line you want to protect, pressing down firmly. Unfold the film so it drapes over the area. Static cling will help it stay in place. Paint as normal. Allow paint to become touch dry. Peel tape back slowly at a 45 degree angle to remove. Size and coverage Width: 550 mm drop Length: 25 m roll Approximate coverage: up to 13.75 m² of drape (when fully unfolded) Specifications Brand UNi-PRO Product type Pre taped masking film Film material High density polyethylene with static cling Tape type Painter’s masking tape Paint compatibility Water based and most solvent based paints Surface compatibility Painted timber, plasterboard, metal, glass, tiles, laminates Dimensions 550 mm x 25 m Pack contents 1 roll  

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $14.43 $11.68

  View options

• Sale -29%

  View options

  Builders Edge Builders Edge Fibreglass Joint Tape for Plaster Reinforcement 50mm x 20m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Strengthen joints, seams, and repairs with this tough fibreglass mesh tape. It helps prevent hairline cracks, improves bond strength, and delivers a smooth base for top coats on plasterboard and cement sheet surfaces. Why you will like it Reinforces joints to reduce cracking around seams and patches Open mesh allows compound to key through for a strong bond Clean edges for easy alignment along butt and tapered joins 50mm width suits standard plasterboard seams and corner work 20m roll is great for rooms, small renos, and ongoing touch ups Great for Plasterboard joins and butt joints Repairs around door and window openings Ceiling crack reinforcement Patching holes and dents before finishing Use with base coat and top coat compounds How to use Ensure the surface is clean, dry, and free of dust. Lay the tape centered over the joint or crack, pressing to seat it flat. Apply a generous first coat of compound through the mesh and let it dry. Feather additional coats wider than the last until flush with the surface. Sand lightly once dry, then prime and paint. Specifications Brand: Builders Edge Type: Fibreglass joint reinforcement tape Width: 50 mm Length: 20 m Material: Fibreglass mesh Colour: White Tips For best results, keep the tape flat with no bubbles before coating. Use a wider knife on each subsequent coat to blend the repair. Allow full dry time between coats to avoid shrinkage lines. Glues Australia helps Australians fix, build, and finish with confidence.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $13.21 $9.32

  View options

• Sale -30%

  View options

  Gorilla Gorilla Black Patch and Seal Tape Stops Leaks Fast 3m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $57.40 $40.04

  View options

• Sale -25%

  View options

  T-Rex T-Rex Clear Double Sided Tape for Invisible Mounting 19mm x 4.5m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Get a clean, hardware free look with T-Rex Clear Double Sided Tape. This high performance clear mounting tape creates a strong, permanent bond for photos, hooks, cable clips, house numbers, trims, and light decor. It is ideal when you want the hold without the hardware and a finish that stays virtually invisible on glass, tiles, metal, and painted walls. Why you will love it Crystal clear finish that helps hide the fix for a neat result Strong permanent bond for everyday mounting and craft projects Moisture and UV resistant construction for long lasting performance Instant stick with pressure activation, no curing time required No tools needed, peel and stick application Great for Mounting signage, house numbers, and name plates Securing cable clips and small hooks Fixing splashback trim and edging Crafts, scrapbooking, and photo boards Temporary holding during light assembly Works on Glass and mirrors Glazed tiles and ceramics Metal, aluminium, and stainless steel Finished timber and laminate Painted walls that are sound, clean, and fully cured Most rigid plastics except low surface energy plastics Note: Not recommended for wallpaper, delicate or dusty surfaces, or low surface energy plastics such as PE, PP, and PTFE. Always test on a small area first. How to use Prepare the surface. Clean with isopropyl alcohol and let dry. Remove dust, grease, and loose paint. Apply tape. Cut to length. Apply tape to the lightest item first. Press firmly along the whole strip. Peel liner. Remove the protective liner without touching the adhesive. Mount. Position carefully. Press firmly for 30 to 60 seconds to activate the bond. Maximum strength develops with time under steady pressure. Removal tips Warm gently and peel back slowly at a low angle Use adhesive remover to clean any residue on robust surfaces Avoid pulling straight out from the wall to reduce risk of paint lift Specifications Brand T-Rex Product type Clear double sided mounting tape Width 19 mm Length 4.5 m Colour Clear Adhesive Acrylic based Indoor or outdoor Indoor and protected outdoor applications Liner Peel off release film Good to know For best results on painted walls, ensure paint is fully cured Heavier items may need additional strips to spread the load Use continuous strips near the edges of flat panels to reduce shear What is in the pack 1 x roll T-Rex Clear Double Sided Tape 19 mm x 4.5 m FAQs Can I use it in wet areasYes for sealed, smooth surfaces such as glazed tiles and glass. Avoid constant immersion. Will it damage paintIt can if paint is weak or not fully cured. Test first and remove slowly with heat to soften the adhesive. Can it hold shelvesThis tape is ideal for light mounting and trim. Use mechanical fixings for shelves and heavy items.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.74 $17.05

  View options

• Sale -14%

  View options

  T-Rex T-Rex White Duct Tape for Indoor and Outdoor Repairs 48mm x 9.1m

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Fast, tough and tidy. This bright white duct tape delivers a strong hold for patching, bundling, sealing and quick fixes indoors and outdoors. It tears by hand for easy application and leaves a clean look on light surfaces. Strong hold for everyday repairs and jobsite tasks Weather resistant backing that helps shed moisture UV resistant colour that stays bright in the sun Hand tear across or along the roll for fast use Conforms to rough, uneven and curved surfaces Clean white finish blends with trim, appliances and walls Great for Sealing and patching around the home, site and shed Temporary cable bundling and gear organisation Quick fixes on tools, hoses, tarps and camping gear Labelling and marking on light coloured surfaces Craft, props and event setups where a white finish is preferred Surface Compatibility Adheres to most clean, dry surfaces including metal, plastic, painted timber, vinyl, glass, masonry, cardboard and fabric. Not recommended on freshly painted walls, delicate finishes, porous stone or where residue free removal is essential. How to Use Clean and dry the surface. Remove dust, oil and loose flakes. Unroll and press the tape down firmly as you go to avoid air pockets. For heavy duty holds, wrap or overlap the tape to increase grip. To remove, lift a corner and peel back slowly at a low angle. Pro Tips At cooler temperatures, warm the tape and surface for best tack. For long term outdoor use, apply to smooth, sealed surfaces. Test first on sensitive areas to check finish and removal. Specifications Brand T-Rex Product type Duct tape Colour White Width 48 mm Length 9.1 m Use Indoor and outdoor Finish Matte white What is in the Box 1 x Roll of T-Rex White Duct Tape 48 mm x 9.1 m Frequently Asked Questions Will it hold in the rain?The backing helps resist moisture and the adhesive bonds well to dry, prepared surfaces. Apply to a clean, dry surface for best results. Is it paintable?Many users paint over duct tape for temporary cosmetics. For the best finish, use a suitable primer and test first. Will it leave residue?Like most strong duct tapes, residue can occur, especially after long exposure to heat and sun. Test on sensitive finishes and remove slowly.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $17.05 $14.74

  View options

• Sale -23%

  View options

  Ramboard Ramboard Joining Tape for Surface Protection Sheets 72mm

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Ramboard Joining Tape is the professional solution for connecting and securing surface protection sheets during construction, renovation, and painting projects. Designed for durability and clean removal, this high-performance tape ensures that your floor and surface coverings stay firmly in place without causing damage or leaving residue. Key Features Strong adhesive for secure bonding between Ramboard sheets Leaves no residue on most surfaces when removed properly Durable and tear-resistant for high-traffic job sites Easy to apply and unwind for fast installation 72mm width for reliable coverage and sealing Ideal For Construction and renovation projects Protecting floors, tiles, and finished surfaces Commercial and residential applications Why Choose Ramboard Tape? This joining tape is engineered to complement Ramboard surface protection products, delivering a tight seal that keeps dust, debris, and spills away from protected surfaces. It is designed to perform under tough site conditions while being easy to remove once the job is done. Specifications Width: 72mm Length: Varies by roll Colour: Brown Adhesive Type: Pressure-sensitive Residue-Free Removal: Yes Pro Tip For best results, apply Ramboard Joining Tape only to Ramboard and not directly to finished floors. Always ensure surfaces are dry and free of dust before application.

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $30.65 $23.62

  View options

• Sale -28%

  View options

  Gyprock Gyprock CSR FibaFuse Joint Tape for Strong Plasterboard Joints

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Achieve smooth, long lasting plasterboard joints with Gyprock CSR FibaFuse Joint Tape. This premium paperless tape bonds beautifully with both setting and drying compounds to reinforce seams, reduce the risk of cracks, and deliver a professional finish on walls and ceilings. Why choose FibaFuse Stronger joints thanks to an open fiber structure that integrates with joint compound for excellent reinforcement. Smooth finishing with feathered edges that sand and paint cleanly. No bubbling when properly embedded in compound for a flat, reliable seam. Works with most compounds including setting type and ready mixed formulas. Ideal for pros and DIY on new installs, repairs, and patchwork. Best for Joining plasterboard sheets on walls and ceilings Butt and tapered edge joints Repairs to cracked or previously patched seams High traffic areas that need extra durability How to use Prep Ensure surfaces are clean, dry, and free of dust. Lightly bevel cut edges if required. Bed coat Apply an even layer of joint compound over the seam at least the width of the tape. Embed Place the FibaFuse tape into the wet compound and press firmly with a taping knife to remove air pockets. Cover Apply a thin coat over the tape to fully conceal the mesh. Allow to dry or set as per the compound directions. Build Apply one or two wider coats, feathering the edges for a flat transition. Let each coat dry before the next. Finish Lightly sand, prime, and paint. Pro tips Keep knife pressure firm during embedding to avoid bubbles. Use a wider knife for second and third coats to reduce sanding. Prime before painting for a consistent sheen across joints and boards. Product details Brand Gyprock CSR Type Paperless joint tape for plasterboard seams Compatibility Setting and ready mixed joint compounds Applications Walls, ceilings, butt joints, tapered edges, repairs Frequently asked questions Do I need to pre soak the tapeNo. Embed the tape directly into wet compound. Can I use it with ready mixed compoundYes. It works with ready mixed and with setting type compounds. Follow the compound instructions for drying or set times. Will it show through paintNot when properly covered with compound, sanded smooth, and primed before painting. Good to know Store flat and dry to maintain tape integrity. Always wear appropriate PPE when sanding joint compound. Glues Australia helps you get a strong, professional finish without the fuss. Why buy new when you can fix

  Read more less

  In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $21.78 $15.70

  View options

Show more products

Trade-grade adhesives, sealants and repair systems designed for durability, productivity and compliance on site. Expect higher strength, specific temperature/chemical resistance and precise application methods (e.g., static-mix nozzles, trowel spreads). Verify standards/approvals where required and follow measured mix ratios, bead sizes and cure schedules. Use filters to refine by chemistry, pot life and service rating. Always consult the product page and TDS/SDS, and observe PPE/safety practices.