PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
$4.19
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
Overview Tired of unreliable glues that fall apart? Meet our game-changing Epoxy Adhesive, a powerhouse in bonding technology. In just a single 25mL package, this epoxy adhesive promises unparalleled durability and convenience. It dispenses effortlessly, ensuring a precise ratio for maximum strength. With a fast-acting formula that's perfect for bonding a variety of materials, your DIY or repair projects just became hassle-free! Features Automatic Self-Mixing Nozzle No more guesswork! Our self-mixing nozzle automatically dispenses epoxy and hardener in the exact ratio for optimal performance. Fast Setting & Long-Lasting Sets in just 5 minutes. Can be safely handled within 30 minutes. Attains full strength after 16 hours. Versatile Usage Ideal for bonding ceramics, glass, leather, wood, plastic, and metal. Your go-to solution for a myriad of projects. Superior Formulation 50% Epoxy Resin 50% Modified Amine Produces a high-strength bond resistant to temperature fluctuations between -40°C and 80°C. How to Use Preparation Safety First: Always wear protective gloves and safety glasses. Surface Preparation: Ensure the surface is clean, dry, and free from dust, oil, and grease. Application Air Removal: Hold the dispenser, nozzle end up, for 30 seconds to release entrapped air. Cut the tip carefully. Dispensing: Press the plunger slowly to dispense equal parts of resin and hardener. Mixing: Mix thoroughly before applying. Bonding: Apply adhesive to the surface and hold until set. Use tape or clamps if necessary. Post-Application Cleanup: Use acetone for cleaning. Storage: Store in a cool, dry place with the nozzle end up.
$9.95
High-Performance Multipurpose Wall & Floor Tile Adhesive This versatile adhesive is designed for fixing almost all tile types to a wide range of challenging surfaces, including water features and swimming pools. Key Features: Suitable for both walls and floors Can be applied over difficult surfaces, including water features Allows tiling over existing tiles Compatible with most types of ceramic and natural stone (excluding moisture-sensitive stone) Tile Types: Ceramic tiles Fully vitrified tiles Natural stone (excluding moisture-sensitive stone) Mosaics Porcelain Suitable Surfaces: Existing tiles Glazed ceramic tiles Metal Roughened fibreglass Timber (particleboard only) Application Areas: Walls and floors Indoor and outdoor Water features and swimming pools Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.4m²/kg 250 x 250mm and larger 10-12mm 0.25m²/kg
$49.42
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$48.79
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safetytips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
The Makita DHP484Z is a compact 18V brushless hammer driver drill built for trades and serious DIYers who want a hard-working, durable drill that can drill, drive and hammer through masonry, all in one tool. It is supplied as a skin (tool only), so it suits anyone who already owns Makita 18V LXT batteries and a charger.About the productThe drill is powered by a brushless motor, which is designed for efficient power delivery and long run times. A durable aluminium gear housing and all-metal gear construction add strength where the drill takes the most load. Makita's XPT protection is designed to guard against dust and moisture, which helps on busy sites and in workshops. A twin LED job light with an after-glow function lights up the work area, and the compact 182mm overall length lets you get into tighter spots.Where to use itIndoors: fitting cabinets and hardware, framing and carpentry, running electrical and plumbing fixings, and general drilling and fastening around the house or workshop.Outdoors: decking and fencing, drilling into masonry and concrete for anchors, and general site work.Suitable for drilling and driving into timber, steel and masonry or concrete (hammer mode), with Makita's rated maximum capacities listed in the specifications below.How to use it Mechanical 2-speed gearbox: use the low gear for driving screws and the high gear for faster drilling. Variable speed trigger with an electric brake for good control. 21 torque settings plus drill mode, so you can match the clutch to the fastener. Single sleeve keyless chuck for quick bit changes. Hammer mode for masonry and concrete, and standard drill mode for timber and steel. Belt clip and a double-ended bit are listed by Makita with this model. Fits Makita 18V LXT batteries (battery and charger sold separately). Important notesThis is a skin only unit, so it does not include a battery, charger or carry case. Capacities and torque figures are maximums under Makita's test conditions, so real-world results will vary with the material, bit and battery used. Always use sharp, correct-size bits and the right mode for the material.Specifications Brand Makita Product 18V Brushless Heavy Duty Compact Hammer Driver Drill Model DHP484Z (skin only) Voltage 18V (LXT) Motor Brushless Chuck Single sleeve keyless No-load speed High: 0 - 2,000rpm, Low: 0 - 500rpm Impact rate High: 0 - 30,000ipm, Low: 0 - 7,500ipm Max lock torque 60Nm Max tightening torque Hard: 54Nm, Soft: 30Nm Max drilling capacity Wood 38mm, Steel 13mm, Concrete 13mm Overall length 182mm Weight (skin) 1.2kg Weight (with BL1860B battery) 1.8kg Batteries and charger Not included Care and storageRemove the battery before changing bits or making adjustments, and wear safety glasses and hearing protection when drilling. Keep the vents and chuck clear of dust, and wipe the tool down after use. Store it in a dry place, out of reach of children. Refer to the manufacturer's instruction manual for full details.
$314.79
The Makita DHP482Z is a compact 18V hammer driver drill built for tradies and serious DIYers who want a short, easy-to-handle tool for everyday drilling and fastening. It is supplied as a skin only, so you can pair it with Makita 18V LXT batteries and a charger you already own.About the productThis model has a short overall body of 198 mm, which makes it easier to manoeuvre in tight spots and overhead. Inside, all-metal gears are used for a tougher transmission. XPT (eXtreme Protection Technology) helps protect the electronics from dust and moisture. A two-speed mechanical gearbox, an electric brake, variable speed trigger control and 21 clutch settings let you match the drill to the job. Two LED job lights with pre-glow and after-glow brighten the work area more widely than a single light would.Where to use itIndoors: fixing cabinets, fitting hardware, driving screws into framing and drilling holes in timber, metal and masonry in confined spaces.Outdoors: decking, fencing, framing and general site work, where the XPT protection helps against dust and splashes.Rated drilling capacity is 38 mm in wood, 13 mm in steel and 13 mm in masonry, and the tool can run in drill or hammer drill mode.How to use it Fit a charged Makita 18V LXT battery (sold separately). Use the speed selector switch on top of the tool to choose the low or high gear. Open and close the single-sleeve keyless chuck with one hand to change bits. Set the clutch collar for driving screws, or switch to the drill or hammer drill setting for drilling. Use the trigger to control speed and the reversing switch to back screws out. Important notesBattery and charger are not included. Use the hammer setting for masonry only, and use a drill mode for timber and metal. The soft grip handle is shaped to help you put weight behind the bit. Always use sharp, correctly rated bits.Specifications Brand Makita Product 18V Hammer Driver Drill Model DHP482Z Supplied as Skin only (no battery or charger) Voltage 18V Chuck Keyless, 1.5 to 13 mm Drilling capacity Wood 38 mm, steel 13 mm, masonry 13 mm No-load speed Low 0 to 600 rpm, high 0 to 1,900 rpm Impact rate Low 0 to 9,000 ipm, high 0 to 28,500 ipm Max fastening torque Hard 62 Nm, soft 36 Nm Clutch settings 21 Overall length 198 mm Weight About 1.2 kg skin only, 1.8 kg with battery Care and storageRemove the battery before changing bits or making adjustments. Keep the vents and chuck free of dust and debris, and wipe the tool clean with a dry or lightly damp cloth. Store the drill in a dry place out of reach of children. Read the instruction manual before use and wear eye protection when drilling.
$243.68
Irwin Strait-Line Permanent Marking Chalk in black is a staining chalk for snap lines and layout marks that need to stay put, supplied as a single 6oz squeeze bottle. It leaves dark, easy-to-see lines on common building surfaces, and the marks stay readable through weeks of weather and jobsite wear.About the productA powder marking chalk made for chalk line reels, sold in a squeeze bottle with a flip-top cap. The cap seals the chalk in an airtight chamber, which keeps moisture out and cuts down on clumping. A Hi-Flow nozzle cap makes refilling a reel quicker and cleaner. Because the chalk stains the surface, you usually don't need a spray sealant to lock the line in.Where to use itIndoors: framing, subfloor and wall layout on surfaces that will be covered, painted or trimmed over, where a permanent line is fine.Outdoors: site and slab layout, decking and fence setout, roofing and sheeting lines, and any marking job where rain, sun and foot traffic would wipe off a standard dust-off chalk.Suitable surfaces include timber, plasterboard, concrete, stone and metal.How to use it Open the flip-top cap and fit the nozzle into the fill opening of your chalk line reel. Squeeze the bottle gently to fill the reel, then close the cap firmly. Wind the line out, pull it taut and snap it to leave a bold black mark. Close the flip-top after every use so the chalk stays dry and free-flowing. Important notesThis is a permanent staining chalk, so the marks are designed to last and can be hard to remove. Do not use it on finished, visible surfaces you want to keep clean, and test an offcut first if you are unsure. Choose a dust-off chalk for temporary marks. Chalk line reel not included.Specifications Brand Irwin Product Strait-Line Permanent Staining Marking Chalk Model number 4935520 Size 6oz (about 170g) bottle Colour Black (Midnight Black) Type Permanent staining powder chalk Container Squeeze bottle with flip-top cap and Hi-Flow nozzle cap Suitable surfaces Timber, plasterboard, concrete, stone, metal Use Exterior and general jobsite marking Care and storageKeep the flip-top cap closed and store the bottle in a cool, dry place so the chalk stays free-flowing. Fill reels gently to avoid raising dust, and wash your hands after use. Wear safety glasses if you are working in windy or dusty conditions. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$6.97
Irwin Strait-Line Hi-Visibility Orange Marking Chalk is a bright, fine powder chalk made for filling reel-type chalk line boxes, giving you lines that stay easy to see on dark surfaces and in poor light. It comes in an 8oz squeeze bottle with a flip-top cap, so refilling your chalk reel is quick and tidy.About the productThis is a powdered marking chalk in a high-visibility orange. The bottle has a flip-top cap that keeps the chalk contained and cuts down on spills while you pour. The cap also seals the contents to help keep moisture out, which reduces clumping and keeps the chalk flowing evenly. Irwin fills its chalk bottles by weight rather than volume, and the bottle has built-in scribe notches. The bright orange is a good choice when white or blue lines would disappear into the background, and it is handy for showing layout changes and corrections over earlier marks.Where to use itIndoors: set-out and layout lines on timber, plasterboard, metal and concrete surfaces, including darker or dimly lit areas.Outdoors: marking lines on concrete, stone, timber and metal on site. Irwin specifies the chalk for exterior use.Suitable surfaces include wood, plasterboard, concrete, stone and metal.How to use it Open the flip-top cap and pour the chalk into your reel-type chalk line box. Fill only as much as the box needs, then close the cap firmly. Pull the line taut over the surface and snap it to leave a bright orange mark. Use orange to flag layout changes and corrections so they stand apart from your original lines. Important notesThis is a refill chalk for self-chalking line reels and is not a crayon or marker. Marking chalk can leave a visible line, so test on a small hidden area first if the finish matters. Keep the cap closed after each use so the chalk stays dry and free-flowing.Specifications Brand Irwin Strait-Line Product Hi-Visibility Marking Chalk Model number 64905ZR Size 8oz (227g) bottle Colour Orange Form Powdered chalk Container Squeeze bottle with flip-top cap Use with Reel-type chalk line boxes Bottle dimensions About 165 x 57 x 43 mm Surfaces Wood, plasterboard, concrete, stone, metal Use Interior and exterior Care and storageKeep the cap closed and store the bottle somewhere cool and dry so the chalk does not absorb moisture. Pour gently to avoid raising dust, and avoid breathing in chalk dust or getting it in your eyes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$9.32
Irwin Strait-Line Blue Marking Chalk is a fine blue chalk powder made for refilling self-chalking line reels, giving carpenters, builders and DIYers a clear, high-visibility guide line that can be removed later. It comes in an 8oz (about 227g) bottle with a flip-top cap, so you can top up your reel quickly and keep the rest of the chalk dry.About the formulaA blue pigmented chalk powder rated as temporary, so the lines show up well while you work and can be wiped, brushed or washed away once the job is done. It suits layout work where you do not want a lasting mark. For lines that must survive weather and months of site wear, choose a permanent chalk colour instead. The flip-top cap closes the bottle to keep moisture out, which helps reduce clumping and spills.Where to use itIndoors: marking layout lines on walls, plasterboard, timber framing and floors for cutting, fixing and setting out.Outdoors: snapping straight lines on concrete, stone, timber and metal for decking, paving, formwork and framing.Suitable surfaces include timber, plasterboard, concrete, stone and metal. Marks are temporary rather than waterproof, so rain or wet conditions will fade or wash them off.How to use itOpen the flip-top cap and pour the chalk into your self-chalking line reel, filling to the level recommended by the reel maker. Close the cap firmly after each use. Then pull the line taut between your two points and snap it against the surface to leave a straight blue line. To clear the mark, wipe or brush it off the surface.Important notesThis is a temporary marking chalk and is not waterproof. Lines on porous or rough surfaces can be harder to remove, so test a small hidden area first if the finish matters. Keep the bottle capped when not in use, because damp chalk clumps and can jam the reel. The chalk is sold on its own, and a chalk line reel is not included.Specifications Brand Irwin Product Strait-Line Standard Marking Chalk Model number 64901 Size 8oz (about 227g) bottle Colour Blue Form Powder Permanence Temporary Waterproof No Application Refill for self-chalking line reels Use Interior and exterior SafetyChalk dust can irritate the eyes and airways, so avoid creating clouds of dust and fill your reel in a well-ventilated spot. Wear gloves and safety glasses if you are filling in bulk or in windy conditions, and wash your hands after use. Keep out of reach of children and store in a cool, dry place with the cap closed. Refer to the Safety Data Sheet (SDS) for full details.
$8.14
30 Seconds Outdoor Cleaner Ready to Use is a fast-acting spray for tackling slimy green growth and slippery black patches on exterior surfaces, supplied here in a handy 1L bottle. There is no mixing or diluting, so it suits quick touch-ups on paths, pavers, decks and outdoor furniture as well as small to medium cleaning jobs around the home.About the formulaA ready-to-use liquid cleaner made to break down algae, moss, mould and mildew and the dirty staining they leave behind. It also helps kill mould and mildew spores on exterior surfaces, which slows the regrowth that brings the stains back. The manufacturer describes the formula as biodegradable and says it is safe to use around the garden.Where to use itIndoors: not intended for indoor use. This is an exterior cleaner.Outdoors: patios, paths, driveways, paving, brickwork, rendered or stucco walls, timber and composite decks, terracotta, and outdoor furniture.Suitable surfaces listed by the manufacturer include brick, ceramic, cobblestone, concrete, composite and timber decking, metals, paving, plastics, stucco, terracotta, concrete tiles and painted or unpainted wood. Use it on hard, colourfast, washable surfaces and test a small hidden spot first.How to use itSpray the product directly onto the affected surface and keep the area wet for at least 30 seconds. For heavier build-up, leave it to work for up to about 10 minutes. Scrub where needed, then rinse off thoroughly with a hose. The cleaner can also be used to prepare exterior surfaces before painting, staining or sealing.Important notesTest on a small, inconspicuous area first, especially on stained timber, fabric, coloured paving, high-gloss paintwork and untreated metals. Results and contact time depend on how heavy the growth is and how porous the surface is. Wear old clothes while spraying, as the product can affect colour in fabrics. Do not mix it with other cleaning products.Specifications Brand 30 Seconds Product Outdoor Cleaner Ready to Use Size 1L Colour Clear Form Ready-to-use liquid Application Spray bottle, then scrub if needed and rinse Contact time At least 30 seconds, up to about 10 minutes for heavy build-up Coverage Approx. 10 m² per 1L Use Exterior surfaces only SafetyUse outdoors or in a well-ventilated area and avoid breathing in the spray mist. Wear gloves and eye protection, and avoid contact with skin and eyes. Keep out of reach of children and pets, and store in a cool, dry place with the lid closed. Refer to the Safety Data Sheet (SDS) for full details.
$18.60
Miracle Brands Outdoor Cleaner is a bleach free, chlorine free concentrate that comes ready to use in a reusable hose end spray bottle, so you can clean large outdoor areas without a bucket or scrubbing for hours. It is made to brighten surfaces and lift the stains that build up on patios, decks, fences and cladding.About the formulaA high performance, water-soluble liquid concentrate that does not rely on bleach or chlorine. It is designed to tackle algae, mould, mildew, dirt, mud, clay, tree sap, pollen, grease, grime, ash and soot. The formula is made to be biodegradable, and the bottle is reusable once the contents are used up.Where to use itIndoors: not intended for indoor use.Outdoors: concrete, pavers, masonry, brick, weatherboards and rendered walls, timber and composite decks, doors, fences, shutters, guttering and trim, letterboxes, garden decor, planters, outdoor furniture and outdoor fabrics.Suitable surfaces include concrete, masonry, brick, rendered surfaces, timber, composite decking, painted and weatherboard cladding, and outdoor fabrics. Test a small, hidden area first on coloured, polished or delicate finishes.How to use itAttach the hose end spray bottle to your garden hose and spray the stained area so it is evenly wet. Let the cleaner work on the surface for the contact time shown on the label, and do not let it dry out on the surface. Scrub stubborn marks with a brush if needed, then rinse thoroughly with clean water. The spray bottle can reach up to 10 metres, which helps with fences, shutters and guttering. Always follow the directions printed on the pack.Important notesWork on one section at a time and rinse the whole area well when finished. Keep the product off surfaces you have not tested if you are unsure how they will react. Results vary with the type and age of the stain, so heavily soiled areas may need a second application.Specifications Brand Miracle Brands Product Outdoor Cleaner Hose End Spray Bottle Model MWOC64 Size 1.89L (single bottle) Form Liquid concentrate Formula Bleach free and chlorine free Application Hose end spray bottle, reach up to 10 metres Use Outdoor surfaces SafetyUse in a well-ventilated outdoor area and wear gloves and safety glasses to avoid contact with eyes and skin. Do not mix with other cleaning products. Keep out of reach of children and store the bottle in a cool, dry place with the cap secured. Refer to the Safety Data Sheet (SDS) for full details.
$40.74
CAgroup Byute Flash is a self-adhesive weatherproofing tape for sealing joints and seams, supplied here as a 100mm x 10m roll for temporary roof, gutter and flashing repairs. It pairs an aluminium foil face with a thick butyl rubber adhesive layer, so it sticks firmly to a wide range of clean, dry building surfaces and is easy to cut and shape on site.About the formulaThe tape has an aluminium foil backing coated with a thick, tacky butyl rubber adhesive. The manufacturer describes it as an all purpose weatherproof sealing tape that adheres permanently to clean, dry surfaces. It is intended as a temporary weather seal and repair solution. Please note that Byute Flash does not comply with AS/NZS 2904:1995 (damp-proof courses and flashings), so it should not be used where a compliant damp-proof course or flashing is required.Where to use itIndoors: sealing joints around doors and where building surfaces meet, and weather sealing seams in toolsheds and similar structures.Outdoors: repairs to roofing, guttering, downpipes and water tank tops, sealing joints around skylights, and weather sealing seams on caravans, trucks and sheds.Suitable surfaces include metals, PVC, brick, fibreglass, cement, glass and timber.How to use itClean the surface thoroughly and make sure it is completely dry before you start. Cut the tape to length with a knife or scissors, then press it firmly onto the surface, smoothing it down and moulding it into place around corners and laps. Where strips meet, overlap them by at least 25mm.Important notesDesigned for temporary weatherproofing and repairs, not as a replacement for a compliant damp-proof course or flashing. Bond strength depends on a clean, dry surface, so remove dust, grease and moisture first. Test on a small area if you are unsure about a particular surface.Specifications Brand CAgroup Building Solutions (Consolidated Alloys) Product Byute Flash Weatherproof Flashing Tape Size 100mm wide x 10m long roll Construction Aluminium foil coated with butyl rubber adhesive Application Hand applied, cut with a knife or scissors Minimum overlap 25mm Use Interior and exterior, residential and commercial Standards Does not comply with AS/NZS 2904:1995 SafetyUse with normal care. Handle the foil edges carefully when cutting and wear gloves if you prefer. Keep out of reach of children and store the roll in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$44.25
FrogTape Pro Grade Deck and Joist Flashing Tape is a linerless, black waterproofing tape made to shield the timber parts of a deck from moisture, supplied here as a 96mm wide x 15.2m roll. It suits deck joists, stair stringers, posts and ledger boards, adding a protective layer over the surfaces most exposed to water, and it is a practical choice for both builders and capable DIYers.About the formulaThe tape pairs a solventless acrylic adhesive (ShurGRIP) with a conformable black polyolefin film backing. The adhesive is made using a UV curing process, is free of volatile organic compounds (VOCs) and is designed not to react with common caulks and sealants. The film bends easily around edges, corners and other transitions, and the tape self-heals around nails, screws and other fasteners to keep a waterproof seal. It is self-wound, so there is no release liner to peel and dispose of, and no primer is needed.Where to use itOutdoors: the tops and sides of deck joists, stair stringers, posts and ledger boards in residential deck construction, where the tape helps keep water away from framing timber.Installation temperature: it can be applied in a wide range, from -18°C to 65°C, and once installed it is designed to keep performing from -40°C to 115°C. It is rated for all-weather performance, including cold and damp conditions, and has 12-month UV resistance while exposed.Suitable surfaces include pressure-treated timber, OSB, concrete and other common building materials. The adhesive is initially repositionable, so you can adjust placement before pressing it down firmly.How to use itMake sure the surface is clean, dry and free of grease, oil and other contaminants. Unroll the tape along the joist, stringer, post or ledger, position it, then press it down firmly so the adhesive makes full contact. Work the tape around edges and corners, and press it into the surface around fasteners. Wider widths wrap further down the sides of a joist, so choose the width that best matches your framing. The same tape is also made in 48mm, 152mm and 304mm widths.Important notesThe manufacturer states the tape meets the AAMA 711-22 flashing tape test protocol. The 12-month UV resistance applies to the tape while it is exposed, so cover it with your decking or cladding in good time. As with any building product, check that it suits your surface and method of application before starting a larger job.Specifications Brand FrogTape Product Pro Grade Deck and Joist Flashing Tape (FSW 058) Size 96mm x 15.2m roll (1 roll) Colour Black Thickness 0.33mm Backing Black polyolefin film Adhesive Solventless acrylic Liner None (self-wound) Application temperature -18°C to 65°C Service temperature after install -40°C to 115°C UV resistance 12 months Standard AAMA 711-22 Use Exterior, above ground deck framing SafetyUse with normal care and keep the roll away from heat and open flame. Wear gloves when handling the tape on site to protect your hands from sharp edges and fasteners. Keep out of reach of children and store the roll in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$75.76
Velcro Extreme Outdoor Hook & Loop Tape is a self-adhesive fastening roll built for outdoor mounting on rough, uneven surfaces, supplied here as a 3 metre roll that is 25mm wide. A heavy duty adhesive backing lets you fix items to brick and concrete without drilling, nails or screws, and the tape is made to cope with sun and weather.About the formulaThe tape pairs hook and loop fastening with a professional grade, heavy duty adhesive backing that is designed to grip rough surfaces. It is UV and weather resistant, so it is suited to exposed spots where ordinary sticky-back tape tends to give up. It holds up to 6.75kg and has an operating temperature range of -18°C to 60°C. Because it is supplied on a roll, you can cut it to whatever length the job needs.Where to use itIndoors: it can be used on rough surfaces inside the home where a strong, drill-free fix is wanted.Outdoors: patios, garden walls, brick and concrete surfaces, for mounting or securing lightweight outdoor items such as decor, signage and gear.Suitable surfaces include rough and uneven masonry such as concrete and brick. Brick varies a lot, so test a small area first.How to use itClean the surface so it is free of dust, dirt and grease, and let it dry. Cut the length of tape you need from the roll, peel off the backing liner, and press the tape firmly onto the surface. Follow the pack instructions for how long to let the adhesive settle before you rely on the hold.Important notesThis tape is not recommended for fabrics, dashboards, flexible vinyl or underwater use. Long, continuous exposure to full sunlight can damage the fastener over time. It is not intended for loads above the stated holding capacity, so spread heavier items across a longer length of tape and test before trusting it with anything valuable or breakable.Specifications Brand Velcro Product Extreme Outdoor Stick On Hook & Loop Tape Roll Size 25mm wide x 3m long (1 roll) Colour Grey Type Self-adhesive hook and loop tape Application Cut to length, peel and stick by hand Holding capacity Up to 6.75kg Operating temperature -18°C to 60°C Resistance Weather and UV resistant Use Outdoor, rough and uneven surfaces SafetyUse with normal care. Keep the tape and offcuts away from young children and pets, and store the roll in a cool, dry place out of direct sun. Refer to the Safety Data Sheet (SDS) for full details.
$31.35
Selleys Liquid Nails VP30 Primer is a rapid-curing, water-based priming concentrate designed as a bridging primer in the Liquid Nails timber flooring system, supplied here in a 1L pack. It is used on concrete slabs and other porous or non-porous surfaces before levelling compounds or flooring adhesives go on, and it flashes off in about 30 minutes so the next stage of the job can start quickly.About the formulaA water-based hybrid polymer primer that is low in VOCs and low in odour. It changes colour as it dries, going on pink and turning red when dry, so you can see at a glance when a coat is ready. Once cured it will not re-emulsify in water, and tools and splatter can be cleaned up with water before the primer cures.Where to use itIndoors: as a bridging primer between Selleys VBS or VBS Rapid moisture barrier and self-levelling compound on concrete slabs, or to prime concrete before self-levelling compound is poured as part of a timber flooring installation.Outdoors: not intended for outdoor use. It is an interior product.Suitable for clean, sound concrete slabs and other porous or non-porous surfaces that will be topped with adhesives or floor skimming and levelling compounds. Check compatibility with your chosen flooring products before starting.How to use itStart with a clean, sound, dust-free surface and stir the primer well before use. Cut in the edges with a brush, then apply with a roller, brush or broom. Allow for roughly 6 to 10 m² per litre, depending on how porous the surface is. Leave a continuous film on the surface so the next layer bonds properly. Pour the primer out onto the floor rather than leaving it in the container, which keeps it cool and gives you more working time. Make sure the primer has dried clear and can be walked on without tackiness before pouring self-levelling compound. Good ventilation helps it cure faster. Clean up with water before the primer cures.Important notesCure time is about 30 minutes, depending on conditions. Very porous concrete or slabs with high moisture content may need a second coat. If the coating soaks away or you see dull patches or pinholes, apply another coat once the first has cured. If you are priming over a moisture barrier, make sure it is fully cured first. Do not apply over dusty or contaminated surfaces, and do not use on surfaces that are subject to standing water. Brushes and rollers are best discarded after use.Specifications Brand Selleys Product Liquid Nails VP30 Primer Size 1L Colour Pink when wet, red when dry Base Water-based Application Brush, roller or broom Cure time About 30 minutes Coverage About 6 to 10 m² per litre, depending on surface Clean up Water, before curing Use Interior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. If product gets on skin, wash with plenty of soap and water, and if it gets in eyes, rinse cautiously with water for several minutes. Keep out of reach of children and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$48.95
Selleys Liquid Nails VBS Rapid is a two-part, water-based epoxy vapour barrier kit that seals concrete slabs before timber flooring goes down, supplied here as a 1.5L resin and hardener kit. Rolled onto a dry, stable slab, it helps block moisture vapour rising from the concrete into the floor above, and its fast-curing formula suits jobs where the flooring needs to go in quickly.About the formulaA pigmented, water-based epoxy supplied as separate resin and hardener components that are mixed together just before use. The colour-coded parts blend to a uniform green, so it is easy to see when the mix is ready, and it is normally applied as a single coat. It has a low odour and can be cleaned up with water while still wet. It is designed to bond well with Selleys Liquid Nails timber flooring adhesives such as Timberflex.Where to use itIndoors: over structurally sound, dry concrete floor slabs, as a moisture vapour barrier under timber flooring that is fixed with a compatible Selleys flooring adhesive.Outdoors: not intended for outdoor use.Suitable surface: clean, dry and stable concrete slabs. Very porous concrete or slabs with high moisture content may need a second coat.How to use itComplete all your preparation and mark out the work area before you start mixing, because this product cures quickly. The slab must be clean, dry and sound, and free of curing compounds, oil, grease, wax, sealers, old coatings and adhesives. New concrete should have cured for at least 28 days or until its moisture content is below 5.5%. Mix the components thoroughly until the colour is even, with no streaks. Tip the mix onto the slab straight away rather than leaving it in the pail, then roll it on with a short-nap mohair roller and cut in the edges with a brush. If a second coat is needed, apply it after the first has cured and before 24 hours have passed. Clean tools with water before the product cures.Important notesDo not apply over damp or contaminated surfaces, or when the temperature is below 10°C or above 35°C. Cure time is rapid and the film is tack-free within hours, but allow for conditions on site such as temperature and slab porosity. Check coverage against your slab: Selleys states roughly 6 to 8 m² per litre per coat. This product is a vapour barrier system, not a flooring adhesive, so use a compatible flooring adhesive over the cured coating.Specifications Brand Selleys Product Liquid Nails VBS Rapid Vapour Barrier Pack 1.5L two-part kit (resin and hardener) Colour Green when mixed Base Two-part water-based epoxy Application Roller, with brush for edges Cure Rapid, tack-free within hours Coverage About 6 to 8 m² per litre per coat Application temperature 10°C to 35°C Clean up Water (before curing) Use Interior, over concrete slabs SafetyUse with normal care: work in a well-ventilated area, avoid contact with skin and eyes, and wear gloves and safety glasses. Keep out of reach of children and store the unused components sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$93.26
Selleys Liquid Nails Timberflex is a flexible, trowel-grade timber flooring adhesive for fixing solid, engineered strip and sheet timber floors to concrete and timber subfloors, supplied here as a single 600ml sausage pack. It is a good fit for smaller flooring jobs, patch work and trial areas where a full pail is more than you need.About the formulaTimberflex uses a silyl modified polymer (MS polymer) technology, which Selleys describes as isocyanate free and solvent free. It stays flexible once cured so the floor can move naturally. It forms clean, stable ridges under the trowel and gives good wet grab and initial hold. It spreads easily across a wide application range of 5°C to 40°C and is a low VOC product that meets Green Building Council requirements.Where to use itIndoors: engineered overlay flooring (prefinished and bamboo) and most types of solid timber, strip and sheet flooring, bonded to common subfloors such as plywood, particleboard, existing strip flooring, fibre cement sheet and concrete, including over acoustic matting.Outdoors: not recommended. This is an interior flooring adhesive and is not intended for wet areas.Suitable materials include plywood, particleboard, existing timber flooring, fibre cement sheet and steel-trowelled concrete.How to use itSurfaces must be clean, sound and level to within 3mm over 3m, because out-of-level floors increase the risk of hollow spots under strip timber. Grind concrete to remove high spots, contaminants and weak surface layers, and sand timber subfloors to remove old glue and other contaminants. Concrete should have a steel-trowel type finish. Over concrete, Selleys recommends a vapour barrier such as Liquid Nails VBS before laying to prevent moisture migration and swelling of the timber. Slab moisture content should be below 5.5% and moisture vapour transmission below 15g/m² per 24 hours. Apply the adhesive to the subfloor and spread it with a suitable Selleys Direct Stick trowel, then lay the boards into the wet adhesive. Wipe uncured adhesive from tools, hands and prefinished boards with a damp cloth before it cures.Important notesAlways follow Australian Standards, NCC requirements and best practice for timber floor installation. Allow about 24 hours for the adhesive to cure. The working time is about 45 minutes at 25°C and 50% relative humidity. Do not apply to dusty, greasy or damp surfaces. Cured adhesive is much harder to remove than wet adhesive, so clean up promptly.Specifications Brand Selleys Product Liquid Nails Timberflex Timber Flooring Adhesive Pack 1 x 600ml sausage Colour Oak Base Silyl modified polymer (MS polymer) Application Trowel applied Application temperature 5°C to 40°C Working time About 45 minutes (25°C, 50% RH) Cure time 24 hours VOC 32g/L Clean up Damp cloth before curing Use Interior timber flooring SafetyAvoid contact with eyes and prolonged or repeated skin contact, and wear gloves when working. Keep out of reach of children. Store in a cool, dry, well-ventilated place out of direct sunlight and away from foodstuffs. Refer to the Safety Data Sheet (SDS) for full details.
$19.06
Selleys Undo Glue Large Hook & Glue is a two-pack of large hooks supplied with a glue that you can undo, so you can hang things around the home without drilling or committing to a permanent fix. It is designed to hold firmly while you use it, then release cleanly when you are ready to move or remove it.About the formulaUndo Glue is Selleys' removable mounting system. Each hook is fixed in place with the supplied glue, and when it is time to take it down the hook is twisted to release it rather than pried or chiselled off. The aim is a strong hold with no damage to the surface when it comes off. The large hook is rated for loads of up to 5kg.Where to use itAround the home: hanging everyday items such as towels, tools, décor and lightweight organisers on walls and other smooth, solid surfaces without drilling.Rentals and tiled areas: handy where drilling is not an option or you want the freedom to rearrange later.Suitable surfaces include tiles, wood, metal, glass, ceramic, concrete, laminated timber, powder coated metal, most plastics and painted walls.How to use itStart with a clean, dry surface free of dust, grease and loose paint. Fix the hook in place using the supplied glue, following the instructions on the pack. Allow 24 hours before hanging anything on it. To remove the hook later, twist it to release the bond, as directed on the pack.Important notesAllow the full 24 hours before loading the hook. Keep loads within the 5kg rating. Test an inconspicuous spot first on delicate, flaking or freshly painted surfaces and on plastics, as results can vary with the surface. Check the pack for any surfaces it is not recommended for.Specifications Brand Selleys Product Undo Glue Large Hook & Glue Pack 2 pack, hardware included Load rating Up to 5kg Ready to hang After 24 hours Removal Twist to undo, no damage Application Glue-fixed hook (not a self-adhesive pad) Surfaces Tiles, wood, metal, glass, ceramic, concrete, laminated timber, powder coated metal, most plastics, painted walls SafetyUse with normal care: work in a well-ventilated area and avoid contact with eyes and skin. Keep out of reach of children and store in a cool, dry place with the cap closed. Refer to the Safety Data Sheet (SDS) for full details.
$11.65
Crommelin Silicone WP Plus is a neutral cure silicone sealant made for wet areas, and it doubles as a bond breaker in Crommelin liquid applied waterproofing systems. This white 300g cartridge suits kitchens, bathrooms, laundries and similar jobs. It stays permanently flexible once cured and contains a mould and mildew inhibitor, so it holds up well in damp, steamy spaces.About the formulaA one-part, neutral cure silicone, so there is no mixing. The neutral cure chemistry will not corrode concrete or zinc coated and galvanised steel. It has a sag resistant body that can be used in vertical and overhead joints. Once cured it resists weathering, UV and vibration, and it is suitable for contact with aluminium shower screens. It can be used as a bond breaking sealant at joints, junctions and corners under waterproofing membranes, or as a durable finishing sealant.Where to use itIndoors: around showers, bath tubs, sinks, laundry fixtures, sanitary ware and spas, plus bond breaking joints in wet area waterproofing.Outdoors: exterior finishing joints and roof and gutter sealing, where the sealant is exposed to weather.Suitable materials include glass, glazed tiles and ceramics, steel and aluminium (suitably prepared), concrete, render, brickwork and blockwork, natural stone, fibre cement sheet and plasterboard. Use it only on clean, sound surfaces.How to use itMake sure the joint is clean, dry and free of dust, grease, soap residue and loose material. Cut the nozzle to suit the joint size, load the cartridge into a caulking gun and apply a continuous bead, then tool it smooth. Where it is used as a bond breaker in a waterproofing system, apply it at all joints, junctions, angles and internal corners before the membrane goes on. Refer to the Crommelin technical data sheet for full application guidance.Important notesThe cured silicone is not paintable, and it should not be used on freshly painted surfaces. Do not use it where it will contact food or potable water. Avoid materials that bleed oils, plasticisers or solvents, because they can affect adhesion. Keep it away from the silver backing of mirrors, such as at mirror edges. It is not a fire rated sealant. Silicone needs moisture in the air to cure, so it will not cure in a sealed, moisture-free environment.Specifications Brand Crommelin Product Silicone WP Plus (Silicone & Bond Breaker) Pack 1 x 300g cartridge (300ml) Colour White Base Neutral cure silicone, one part Application Cartridge, via caulking gun Features Mould and mildew resistant, permanently flexible, UV and weather resistant, sag resistant Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses where sensible. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$16.71
UCCC Builders Filler is a polyester resin based filler for filling, building up and smoothing surfaces, supplied here in a 750ml pack. It is made for everyday handy people as well as tradies, and it mixes, applies and sands easily. It suits a wide range of materials, including automotive repair work.About the formulaThis is a thermosetting two-pack polyester filler, so you mix it with its hardener before use. It sets to a hard, sandable finish that holds its shape without shrinking. The paste is off-white or beige-brown. It can be applied to horizontal or vertical surfaces. Once cured, it can be painted or stained.Where to use itIndoors: filling and levelling timber, repairing dents and gaps in metal, and general building and renovation repairs.Outdoors: repairs on exterior timber, concrete, metal and fibreglass. The cured filler is UV resistant.Automotive: suitable for body repair work.Suitable materials include metals (including galvanised steel), concrete, fibreglass and timber, plus many other substrates. As with any filler, test a small area first if you are unsure about a particular surface.How to use itMake sure the surface is clean, dry and free of grease, dust, loose paint and rust. Sand or key smooth surfaces for a better grip. Mix only as much filler as you can use in one go, blending in the hardener thoroughly as directed on the pack. Press the mixed filler firmly into the repair, working it in to avoid air pockets. Build it slightly proud of the surface, then let it harden fully. Sand it flush and smooth, then prime and paint or stain as needed.Important notesAlways follow the mixing directions on the pack, because the amount of hardener affects how quickly the filler sets and how well it cures. Warm conditions speed up setting and cool conditions slow it down. The filler is dry to touch in about 20 minutes, and you should sand it only once it has hardened properly. Close the tin tightly after use. Hardened filler cannot be reused.Specifications Brand UCCC Product Builders Filler Size 750ml Colour Off-white or beige-brown Base Polyester resin, two-pack (mixed with hardener) Application Hand applied with a spreader or putty knife Dry to touch About 20 minutes Finish Sandable, paintable and stainable Properties Shrink resistant, UV resistant Use Interior and exterior SafetyUse with normal care. Work in a well-ventilated area, keep away from heat and open flame, and avoid contact with eyes and skin. Wear gloves and safety glasses, and use a dust mask when sanding. Keep out of reach of children and store in a cool, dry place with the lid tightly closed. Refer to the Safety Data Sheet (SDS) for full details.
$26.23
Selleys Tradie's Bog is a fast-setting, two part polyester building filler for repairing timber and most common building materials, supplied here in a 550g pack. It is built for quick, hard-wearing repairs where a lightweight filler would not hold up, and it can be sawn, drilled, sanded and painted once set. About the formulaA cream polyester resin paste that you mix with the supplied hardener to start the cure. It grips well to a wide range of building surfaces and sets hard in around 20 minutes, with minimal shrinkage, so you can shape it, sand it and move on to painting quickly. The cream base can be tinted with cement oxides or paint tinters if you add the colour before the hardener. Where to use itIndoors: repairing window and door frames, architraves, skirting boards and sashes, and filling holes, cracks and damaged edges in timber and plasterboard.Outdoors: patching external timber joinery, masonry, concrete and metal, then finishing with a suitable paint system. Suitable materials include timber, plasterboard, concrete, brick, fibreglass, metal, alloy, tiles and ceramics. How to use itMake sure the area to be repaired is clean, dry, unpainted and free of oil and grease. Stir the bog before use, then work out a short ribbon of hardener (about 2.5cm for every heaped tablespoon, or roughly 20g, of bog) and mix thoroughly on a clean surface until the colour is even. Press the mix into the repair with a spatula and overfill slightly. For dents in steel or aluminium that will see heavy vibration, punching or drilling the metal first gives the filler a better key. Shape off the excess with a Surform or rasp before it goes rock hard, then use ordinary files or sandpaper once fully set. Clean tools with mineral turpentine before the product cures. Important notesWorking time is about 5 minutes at 23°C, so mix only what you can apply straight away. The filler is rigid, so it is not suited to joints or areas where movement is expected, nor to areas under constant water immersion. It will not bond to polyethylene, polypropylene or PTFE (Teflon). Colour must be added before the hardener. The filler can be painted once cured. Specifications Brand Selleys Product Tradie's Bog Two Part Polyester Building Filler Pack 550g (filler with hardener) Colour Cream Base Two part polyester Application Mixed by hand and applied with a spatula Work time About 5 minutes at 23°C Cure time About 20 minutes Finishing Can be sawn, drilled, tapped, sanded and painted Clean up Mineral turpentine (before cure) Use Interior and exterior SafetyUse in a well-ventilated area, away from heat and open flame, and wear gloves and safety glasses when mixing and sanding. Avoid contact with skin and eyes. Keep out of reach of children and store the pack tightly closed in a cool, dry place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$32.71
Selleys Flexiseal Clear is a premium, crystal-clear multipurpose elastic joint sealant for DIYers and tradies who want a flexible, weather-tough seal that stays discreet. Supplied in a 290ml cartridge, it handles everyday sealing jobs indoors and out, and it can be applied to damp or wet surfaces without a primer.About the formulaBuilt on Selleys hybrid technology (a moisture-curing silyl-modified polymer), this sealant has a low modulus, non-slumping body that stays put in joints up to 20mm wide. It cures to a strong, elastic, waterproof seal that resists UV and weathering and keeps its clear finish. It is free from solvents and isocyanates, has a low odour, and meets Green Building Council of Australia low VOC limits for general purpose and architectural sealants. Once cured it can be painted with water-based paints.Where to use itIndoors: gaps and joints around windows, doors, skirtings, trims and fittings where a clear, flexible seal is wanted.Outdoors: vertical and horizontal joints in exterior cladding, around frames and between common building materials exposed to sun and rain.Suitable materials include concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles and glass, along with most other common building surfaces. Test first on painted surfaces and any unusual materials.How to use itClean the joint and remove dust, grease and other contaminants, and degrease metal surfaces. Cut the nozzle at an angle, slightly wider than the joint, and load the cartridge into a caulking gun. Use a suitable backing rod to control depth where needed. Gun the sealant into the joint and tool it off promptly so it makes good contact with both sides. Remove excess uncured sealant with a damp cloth. Paint with water-based paints once the surface has skinned or cured.Important notesNot suitable for polyethylene, polypropylene or Teflon (PTFE). Not intended for permanent water immersion. Application is best between 5°C and 35°C. Cure time depends on temperature, humidity and joint depth, so allow enough time before putting the joint under stress or exposing it to water.Specifications Brand Selleys Product Flexiseal Clear Multipurpose Sealant Pack 290ml cartridge Colour Clear Base Moisture-curing silyl-modified polymer (hybrid technology) Application Cartridge, via caulking gun Skin time About 45 minutes (23°C, 50% RH) Non-slump Joints up to 20mm wide Density Approx. 1.05 g/mL Application temperature 5°C to 35°C Service temperature -20°C to 70°C Paintable Yes, with water-based paints Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. Keep out of reach of children and store in a cool, dry place with the cartridge sealed. Refer to the Safety Data Sheet (SDS) for full details.
$23.03
Sika SikaBond 142 Instant Nails is a high-strength, multipurpose construction adhesive for fixing panels, timber and sheeting, supplied here as a trade pack of twelve 300g cartridges for busy sites and larger renovation jobs. It is a ready-to-use, single-component adhesive with a thick body that stays put on vertical surfaces, so it suits fixing work where you would otherwise reach for extra nails or screws.About the formulaA one-component synthetic rubber adhesive in a beige, non-slump paste. It can be used as a one-way adhesive (apply to one surface and join straight away) or as a two-way contact adhesive (apply, press together, separate, let it skin, then rejoin). It has a short skinning time of about 1 to 5 minutes, and a bond that develops quickly. The cured adhesive can be painted over.Where to use itIndoors: floor and wall panels, timber, particleboard, MDF and plywood fixed to frames, plus plasterboard and similar sheet linings.Outdoors: cement sheeting, fibreglass, concrete and masonry fixing jobs that are not constantly wet or immersed.Suitable materials include floor and wall panels, timber, particleboard, MDF, plywood, plasterboard, aluminium, iron and steel, concrete, cement sheeting, fibreglass and masonry. Test an offcut first if you are working with a material that is not on this list.How to use itMake sure surfaces are sound, clean, dry and free of dust, oil, grease and loose material. Cut the nozzle and apply the adhesive in a bead with a standard caulking gun. For the one-way method, bring the surfaces together straight away and press firmly. For the two-way method, press the surfaces together to transfer the adhesive, pull them apart, wait for it to skin over, then rejoin them with firm pressure. Tapping the work with a hammer and a padded block helps ensure full contact. Heavy panels may need temporary mechanical fixing until the bond has developed. Clean tools straight away with Sika Colma Cleaner or mineral turpentine. Once cured, the adhesive can only be removed mechanically.Important notesMaximum bond strength is reached in about 12 to 72 hours, and full cure takes about 7 days depending on weather conditions. Do not use it for immersed applications, do not apply it when the temperature is below 5°C, and avoid damp, unseasoned or treated timber. Store unopened cartridges in a dry place between 5°C and 25°C. Shelf life is 18 months from the production date.Specifications Brand Sika Product SikaBond-142 Instant Nails Construction Adhesive Pack 12 x 300g cartridges Colour Beige Base One-component synthetic rubber, solvent-based Application Cartridge, via caulking gun Skinning time 1 to 5 minutes Maximum bond strength 12 to 72 hours Full cure About 7 days Yield About 15 linear metres per cartridge (continuous 5mm bead) Service temperature 0°C to 40°C Application temperature 5°C to 40°C (substrate) Shelf life 18 months SafetyUse with normal care: work in a well-ventilated area, keep away from heat, sparks and open flame, and avoid contact with skin and eyes by wearing gloves and safety glasses. Keep out of reach of children and store the cartridges in a cool, dry place with the nozzle capped. Refer to the Safety Data Sheet (SDS) for full details.
$60.05
SikaBond-142 Instant Nails is a high strength, multipurpose construction adhesive that holds its place on vertical surfaces, supplied here as a trade pack of six 300g cartridges. It works as a one-way liquid adhesive or as a two-way contact adhesive, so it suits quick panel fixing as well as bonding jobs where you want an immediate grab.About the formulaA one-component, ready-to-use synthetic rubber dispersion in a beige, non-slump paste. The bead stays put on walls and ceilings instead of sagging, skins over within about 1 to 5 minutes and dries quickly. The Sika data sheet reports tensile strength above 1 MPa on a dry substrate (tested to AS 2329) and peel adhesion above 40 N. Once cured, it can be painted over.Where to use itIndoors: floor and wall panels, skirting and trim, and panelling fixed to timber or metal backing.Outdoors: Sika does not list exterior use on its data sheet, so check suitability for your application before using it outside. It is not suitable for permanently immersed applications.Suitable materials include timber, particleboard, MDF, plywood and plasterboard, aluminium, iron and steel, and concrete, cement sheeting, fibreglass and masonry.How to use itSurfaces should be clean, sound and dry, with oil, grease, dust and loose flaking material removed. Light abrasion helps adhesion. Load a cartridge into a standard caulking gun and apply a bead. For one-way use, press the panel into place. For two-way contact bonding, coat both surfaces, allow the adhesive to skin over, then press together firmly. Apply only when the surface temperature is between 5°C and 40°C.Important notesFull cure takes about 7 days, depending on weather conditions. Do not apply below 5°C, and do not use on damp, unseasoned or treated timber. Service temperature range is 0°C to 40°C. Not suitable for immersed applications. Test on an offcut first if you are unsure about a surface.Specifications Brand Sika Product SikaBond-142 Instant Nails Construction Adhesive Pack 6 x 300g cartridges Colour Beige Base 1-component synthetic rubber dispersion Application Cartridge, via caulking gun Skinning time 1 to 5 minutes Full cure About 7 days Yield About 15 linear metres per cartridge (continuous 5mm bead) Application temperature Substrate 5°C to 40°C Service temperature 0°C to 40°C Shelf life 18 months from production, stored unopened Standard Tensile strength tested to AS 2329 SafetyUse with normal care: work in a well-ventilated area, keep away from heat and open flame, and avoid contact with skin and eyes by wearing gloves and safety glasses. Keep out of reach of children and store unopened cartridges in a dry place between 5°C and 25°C. Refer to the Safety Data Sheet (SDS) for full details.
$31.19
Selleys Liquid Nails Original is the go-to multipurpose construction adhesive for builders and DIYers, supplied here as a bulk 20 pack of 320g cartridges for busy sites, workshops and anyone who wants to stock the ute. It forms a strong, long-lasting bond across most common building materials and stays flexible enough to cope with the shrinkage and thermal movement that can weaken rigid bonds over time.About the formulaA solvent-based adhesive with a firm body that is designed not to drip, sag or string, so jobs stay tidier. It bonds to both wet and dry timber, bridges gaps on rough or ill-fitting materials, extrudes easily in cooler conditions and can be painted once dry. It is water and weather resistant and meets Australian Standard AS 2329 (1999).Where to use itIndoors: panelling, wallboard and plasterboard to timber or metal frames, skirtings, architraves, timber battens, MDF and particleboard fixing.Outdoors: timber to timber, timber or sheeting to masonry, concrete and brick surfaces, and general weather-exposed building and repair jobs.Suitable materials include timber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, rubber and glass. Most plastics can be bonded, but test a small area first to check compatibility.How to use itMake sure surfaces are free of oil, grease and dust, and wipe any pooled water off wet timber. Cut the cartridge tip, fit the nozzle and cut it to a opening of about 5mm. Apply a bead along the length of the joist, stud or batten, or run beads about every 40cm on broad flat surfaces. Press the pieces firmly together and fix with enough nails, screws or clamping to carry the load and keep contact across the whole bond area. The adhesive stays repositionable for up to about 20 minutes after fitting. For a faster initial grab, apply to one surface only, let it dry briefly, then press together. Leave to set for at least 24 hours before removing temporary fasteners or clamps. Clean uncured adhesive with mineral turpentine; cured adhesive must be scraped or sanded off.Important notesA strong bond usually develops within 24 hours and keeps building over 2 to 3 days, with full cure in about 7 days. Allow longer for thick applications, less porous surfaces and cold weather. For high-stress applications, use with mechanical fasteners. Not suitable for polyethylene, polypropylene, Teflon, silicone or polystyrene foam, and not for permanent water immersion. Not intended for mirrors; use a dedicated mirror adhesive for those jobs.Specifications Brand Selleys Product Liquid Nails Original Construction Adhesive Pack 20 x 320g cartridges Colour Brown / beige Base Solvent-based Application Cartridge, via caulking gun Coverage Approx. 3m per cartridge (5mm bead) Repositionable Up to about 20 minutes Strong bond Usually within 24 hours Full cure About 7 days Standard AS 2329 (1999) Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, keep away from heat and open flame, avoid contact with eyes and skin, and wear gloves and safety glasses. Keep out of reach of children and store in a cool, dry place with the nozzle capped. Refer to the Safety Data Sheet (SDS) for full details.
$131.75
Selleys Liquid Nails Original in the 680g sausage pack is a multipurpose construction adhesive for builders and DIYers who get through a lot of adhesive, with more product per pack than a standard cartridge and fewer changeovers on big jobs. It gives a strong, lasting bond on most common building materials and stays flexible enough to cope with the shrinkage and thermal movement that can weaken rigid bonds over time.About the formulaA solvent-based adhesive that holds its shape without dripping, sagging or stringing, so application is tidy. It bonds well to both wet and dry timber, so there is no need to wait for timber to dry out, and it extrudes easily in cooler weather. It also bridges gaps on rough or ill-fitting building materials, resists water and weather once cured, and can be painted over for a neat finish. It meets Australian Standard AS 2329.Where to use itIndoors: sheet flooring to joists, wallboard or panelling to timber or metal frames, cork tiles to timber, fibro or plaster, metal or aluminium door strips to floors or walls, and squeaky tongue and groove boards.Outdoors: timber or fibre cement sheeting to brick or cement block walls, and masonite to timber.Suitable materials include timber, plasterboard, MDF, particleboard, fibre cement sheeting, brick, masonry, concrete, render, tiles and ceramics, metals, rubber and glass. Test plastics for compatibility before committing to a full job.How to use itMake sure surfaces are free of oil, grease and dust, and wipe off any pooled water from wet timber. Fit the sausage pack into a suitable sausage-style applicator gun and run a bead along the joist, stud or batten. On broad, flat surfaces, apply beads about 40cm apart. Press the pieces firmly together and fix with enough nails, screws or clamping to hold the load and keep full contact across the bond area. You can reposition the work for up to about 20 minutes after fitting. Leave the adhesive to set for at least 24 hours before removing any temporary fasteners or clamps. Clean uncured adhesive with mineral turpentine; cured adhesive needs to be scraped or sanded off.Important notesA strong bond is usually reached within 24 hours and keeps building over the next few days, with full cure in about 7 days. Allow longer for thick applications, less porous surfaces and cold weather. Not suitable for styrene foam, for permanent water immersion, or as the only bonding method in structural applications.Specifications Brand Selleys Product Liquid Nails Original Construction Adhesive Pack 1 x 680g sausage Colour Brown Base Solvent-based Application Sausage pack, via sausage-style applicator gun Repositionable Up to about 20 minutes Initial set About 24 hours Full cure About 7 days Standard AS 2329 Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, keep away from heat and open flame, avoid contact with eyes and skin, and wear gloves and safety glasses. Keep out of reach of children and store in a cool, dry place with the pack sealed. Refer to the Safety Data Sheet (SDS) for full details.
$14.05
Selleys Undo Glue Small Hook & Glue is a commitment-free way to hang lightweight items, supplied here as a pack of four small hooks with glue. It is designed to give a firm hold during use, then release cleanly with a simple twist, so you can hang, mount and rearrange things around the home without drilling or leaving permanent marks.About the systemEach pack combines small hooks with Selleys Undo Glue, a bonding system made for temporary fixing. The hold is rated by the manufacturer for loads up to 2kg, and the hooks are made to come away without damaging the surface when you are ready to move or remove them. The glue is not self-adhesive, so it is applied as part of the hook installation rather than coming pre-applied on a tape.Where to use itIndoors: hanging lightweight items on tiled walls, painted walls, timber and other smooth household surfaces where drilling is not wanted.Around the home: kitchens, bathrooms, laundries, hallways and rental-friendly spots where you want to avoid permanent fixings (check the pack for any exterior or wet-area limits).Suitable surfaces include tiles, wood, metal, glass, ceramic, concrete, laminated timber, powder coated metal, most plastics and painted walls.How to use itMake sure the surface and the hook base are clean, dry and free of dust, oil and grease. Apply the glue and fix the hook as shown in the instructions on the pack, then leave it undisturbed so the bond can develop. When you want to remove a hook, use the twisting action described on the pack rather than pulling it straight off. Always follow the printed directions for your pack, as they take priority over this summary.Important notesAllow 24 hours before hanging anything on the hook. Do not exceed the stated 2kg limit. Test on an inconspicuous spot first if you are using it on delicate, freshly painted or unusual finishes, and test plastics before committing to a final position. Because the system is designed to release cleanly, it is intended for lightweight hanging rather than permanent or load-bearing fixing.Specifications Brand Selleys Product Undo Glue Small Hook & Glue Pack 4 hooks with glue Hardware included Yes Self-adhesive No (glue applied during installation) Maximum hold Up to 2kg Ready to hang After 24 hours Removal Twist to release Pack size (approx.) 220 x 135 x 35 mm SafetyKeep out of reach of children. Avoid contact with eyes and skin, and wash your hands after use. Do not swallow the glue. Store in a cool, dry place with the lid or cap closed. Refer to the Safety Data Sheet (SDS) for full details.
$8.15
Selleys Undo Glue is a removable mounting glue for hanging and fixing items around the home without making a permanent commitment, supplied here in a 10g pack. It is designed to hold firmly, then come away cleanly later without damaging the surface, so you can hang, mount and rearrange things without drilling.About the formulaA ready-to-use, pre-mixed adhesive, so there is nothing to blend or activate. It is made to give a strong hold while still allowing clean removal when you want to move or take down the item. It is made to be used with Selleys Undo Glue Hooks, and can also be used to mount lightweight items such as posters, photos and decorations. Once applied it is not drillable or sandable.Where to use itIndoors: hanging hooks, posters, photos and decorations on painted walls, tiles and other smooth household surfaces, in places where drilling or a permanent fix is not wanted.Around the home: kitchens, bathrooms, laundries, hallways, rental properties and kids' rooms where a removable fix is handy.Suitable surfaces include tiles, wood, metal, glass, ceramic, concrete, laminated timber, powder coated metal, most plastics and painted walls. Test on a small, hidden area first, especially on plastics and delicate paint finishes.How to use itMake sure the surface and the item you are mounting are clean, dry and free of dust, grease and loose material. Apply the glue as directed on the pack, press the item into position and hold it as the label advises. Allow the full cure time before putting any weight on it. Follow the directions printed on the pack for the item you are mounting and for removal.Important notesAllow around 24 hours for the glue to cure fully before loading the item. Not intended for permanent structural fixing. Check the label for weight limits and unsuitable surfaces, and do not exceed the stated load. Surface condition, paint quality and the type of material can all affect hold and clean removal, so a test patch is recommended.Specifications Brand Selleys Product Undo Glue Pack 10g Type Removable mounting adhesive, pre-mixed Cure time 24 hours Drillable No Sandable No Compatible with Selleys Undo Glue Hooks Use Household mounting and hanging SafetyAvoid contact with eyes and skin, keep out of reach of children, and wash hands after use. Store in a cool, dry place with the cap or lid closed. Refer to the Safety Data Sheet (SDS) for full details.
$11.65
Davco Lanko 136 Rapid Patching Mortar is a fast-setting, cement-based repair mortar for patching concrete, brickwork and rendered surfaces, supplied here in a 5kg bag that suits small to medium repairs. It gains strength very quickly, so floor finishes, underlayments and coatings can go over the repair in a fraction of the time that a standard patching mix needs.About the formulaA one-part, pre-blended grey powder made from cement, selected aggregates and special additives. It is polymer modified, so you only add clean water. Davco describes it as shrinkage compensated to help resist cracking as it cures, with a fine, workable finish. It sets rapidly and develops very high early strength, and the manufacturer lists it as freeze/thaw resistant once cured. It is not a vapour barrier.Where to use itIndoors: patching holes, chips and defects in concrete floors before levelling compounds, underlayments, carpet, vinyl or ceramic tiles go down; forming small ramps or transitions before floor coverings; treating chamfers, coves and seams before waterproofing membranes or epoxy coatings.Outdoors: repairing concrete slabs, pillars and posts; patching brickwork and rendered walls before tiling, coating or painting.Suitable materials include concrete, brick, block, masonry and cement render. Always apply it to a sound, properly prepared surface.How to use itRemove dust, loose material, oil, grease and anything else that could stop a bond. Dense, power-floated concrete may need a bonding primer or moisture barrier first, so check the Davco data sheet for the recommended options. Mix with clean potable water only, at about 0.53 to 0.6 litres per 5kg bag. Add the powder to most of the water while mixing, then adjust to a workable consistency with a drill and paddle or by hand. Mix only what you can place within roughly 15 minutes. Press a first pass firmly into the surface with a steel trowel, build up to the required thickness, then finish with a wet steel trowel or foam float. Do not vibrate the mortar into place, and discard any mix that starts to stiffen.Important notesDo not apply in direct sun or strong winds, and keep the air and surface temperature at or above 7°C. Do not feather edge this mortar. It is a repair material and not a wearing surface, so cover it where it will be exposed to wear. The manufacturer's guide is that floor finishes and underlayments can go on after about 90 minutes. Foot traffic is possible in about 45 minutes at 23°C, and epoxy coatings can go on from about 4 hours (do an on-site test first). Deeper or heavy-load repairs need extra care and cure time, so follow the data sheet. Strength figures vary with the aggregates and site conditions.Specifications Brand Davco (Lanko range) Product Lanko 136 Rapid Patching Mortar Pack 5kg bag Colour Grey powder Base Cementitious, polymer modified Application Mixed with water, applied by steel trowel Mixing ratio About 0.53 to 0.6 L water per 5kg bag Yield About 2.5 L per 5kg bag Compressive strength About 13 MPa at 1 hour, about 80 MPa at 28 days (23°C) Ready for floor finishes From about 90 minutes Storage Sealed, dry, between 5°C and 35°C Use Interior and exterior SafetyAvoid breathing dust, and wear gloves, protective clothing and eye or face protection. Remove contaminated clothing and wash it before reuse. If it gets on skin, wash with plenty of water. Store the sealed bag dry and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$34.72
Sika Abelrod is a lightweight closed cell polyethylene foam rod used to fill and set the depth of expansion joints and gaps before sealant goes in, supplied here as a 10mm x 50m roll. It acts as a bond breaker and depth control behind the sealant, so the finished joint can flex properly, and it recovers well after being compressed so it keeps a tight barrier against dirt and water.About the materialAbelrod is a closed cell polyethylene foam with a white finish. Sika describes it as strong for its weight, highly resistant to weathering and most common chemicals, and a suitable filler to install ahead of most sealants. Its recovery properties let it cope with years of joint compression and expansion. It meets the requirements of Australian Standard AS2170 for plastic materials in food contact use. Sika lists the density at 30 kg/m3.Where to use itIndoors: joints in interior walls, around skylights and as a filler behind sealant in internal gaps, plus draft proofing and dust sealing.Outdoors: vertical and horizontal joints in concrete and masonry, joints between precast concrete panels, shop fronts and curtain wall construction, and swimming pool areas.Suitable for joints in concrete and masonry substrates. It also suits general gap filling, sealing electrical control boxes, truck and trailer construction and use as piping around chairs.How to use itMake sure the joint surfaces are dry, clean and free of dust, dirt, grease, oil and wax. Press the rod into the joint so it sits at the right depth for your sealant, and compress it by about 30% once in position so it holds firmly and forms a good seal. Apply your chosen sealant over the top once the rod is seated.Important notesCheck the sealant manufacturer's recommendations for joint width, depth and compatibility before you start. Store the rod in a cool, dry area out of direct sunlight. Sika states that the product has an unlimited shelf life when stored dry.Specifications Brand Sika Product Abelrod Gap Filler (Abelflex Rod filler) Size 10mm diameter x 50m roll Colour White Material Closed cell polyethylene foam Density 30 kg/m3 Compression when installed About 30% Standard Meets AS2170 (plastic materials for food contact use) Storage Cool, dry area away from direct sunlight Use Interior and exterior SafetyKeep it away from open flame and heat sources, as foam products can burn and give off irritating fumes when heated or burned. Handle with normal care and dispose of offcuts in line with local waste rules. Refer to the Safety Data Sheet (SDS) for full details.
$44.94
One On One Heavy Duty Double Sided Sealing Tape from CAgroup (Consolidated Alloys) is a butyl rubber tape that sticks and seals in a single step, supplied here as a 48mm x 5m roll. It is aimed at builders, roofers and DIYers who need a tacky, water-resistant seal between building materials, membranes and sheeting without mixing, gunning or waiting for anything to cure.About the formulaThe tape is a highly water-resistant butyl rubber sealant supplied on a siliconised kraft paper release liner, which peels away cleanly so the tape is easy to handle and position. The soft butyl adhesive conforms to rough and textured surfaces, so it can follow uneven substrates and fill small surface irregularities as it is pressed into place. It is described by the manufacturer as suitable for joining, sealing, waterproofing and absorbing vibration.Where to use itIndoors: joining and sealing builders film, polythene sheeting and sisalation foil, and damping vibration or noise on audio parts and similar fittings.Outdoors: sealing joints for waterproofing in construction and joining and sealing membranes on building sites.Suitable materials include glass, metal, wood, rendered concrete and plastics, including both high and low energy surfaces. Always test a small area first on unfamiliar plastics or coated surfaces.How to use itMake sure the surfaces are clean, dry and free of dust, oil, grease and loose material. Measure and cut the tape to length, peel back the kraft liner as you go, and position the tape without stretching it. Press the tape down firmly along its full length, then bring the second surface or membrane into place and apply even pressure so the butyl makes full contact. If the substrate is very rough, press harder or work the tape in so it can conform to the texture.Important notesButyl tape is a soft, pressure-sensitive sealant, not a structural adhesive, so do not rely on it alone to carry heavy loads. Butyl rubber can be softened by some solvents, so keep it away from solvent-based products unless you have checked compatibility. The manufacturer has not supplied application temperature limits, service temperature range, thickness or standards compliance figures for this size, so none are stated here. If you need compliance with a specific standard or approval (for example for damp-proof courses), confirm it with CAgroup before use.Specifications Brand CAgroup (Consolidated Alloys) Product One On One Heavy Duty Double Sided Sealing Tape Size 48mm wide x 5m long roll Pack Single roll Base Butyl rubber Format Double sided tape with siliconised kraft paper release liner Application Hand applied, press into place Use Joining, sealing, waterproofing and vibration absorption SafetyAs general good practice, keep the tape away from heat and open flame, avoid prolonged skin contact with the adhesive, wash your hands after handling, and store the roll in a cool, dry place out of direct sunlight and away from children. Refer to the Safety Data Sheet (SDS) for full details.
$11.10
![Davco K10 Plus Waterproofing Membrane 20L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/davco-k10-plus-waterproofing-membrane-20l-grey-2.jpg?v=1792411411&width=645)
Davco K10 Plus is a premixed, ready-to-use, water-based polyurethane waterproofing membrane for tradies and builders, supplied here as a 20L pail in grey. It is a Class III membrane designed to sit under tile, stone and other resilient finishes on both walls and floors, in domestic and commercial jobs.About the formulaA one-part, water-based polyurethane that goes on straight from the pail with no mixing. It is rated Class III under AS/NZS 4858 and is highly flexible, with elongation above 500%. The manufacturer also lists it as non-toxic, UV stable and suitable as an anti-fracture membrane. Because it is water-based and solvent-free, it suits confined areas. Published technical figures include a Shore A hardness of 72 and a tensile strength of 2.1MPa.Where to use itIndoors: walls and floors in showers, bathrooms and other wet areas, ahead of tiling.Outdoors: terraces, balconies, roofs and walkways that will be covered with a hard finish such as tile.Suitable substrates include concrete, cement render and screeds, lightweight blocks, building boards approved for wet areas (such as compressed fibre cement sheet) and prepared metal surfaces. Metal needs an etching primer. All substrates should be primed with a suitable Sika primer before the membrane goes on.How to use itPrepare the substrate so it is sound, clean and primed. New render or screed needs a wood float finish and should cure before you start. Where falls are not already in place, form them with a sand and cement screed first. Apply the membrane by brush or roller in a minimum of two coats to reach a 1mm dry film. Each coat should go on at a wet film thickness of at least 0.75mm. Let the first coat dry for about 1 to 2 hours, then apply the second coat at 90 degrees to the first. Add further coats if needed to reach the minimum dry film thickness. Tools can be cleaned with water while the product is still wet. Tile over the cured membrane using a Sika polymer-modified cement-based tile adhesive.Important notesAllow about 6 to 8 hours before tiling or applying other finishes. Allow 3 days before flood testing and 5 days before the area returns to service. Drying times vary with temperature, humidity and film thickness. The membrane is not designed to be left exposed, so it must be covered with a finish. Follow the current Sika data sheet for primer selection, bond breakers, corners and joints, and for any movement joints. Wet area waterproofing must be done to the relevant Australian Standards and building code requirements, so use a licensed applicator where required. Shelf life is 12 months from manufacture. Store in a cool, dry place out of direct sunlight and do not let it freeze.Specifications Brand Davco (Sika) Product K10 Plus Waterproofing Membrane Pack 20L pail Colour Grey Base Water-based polyurethane, one part, premixed Classification Class III (AS/NZS 4858) Application Brush or roller Elongation Greater than 500% Coverage Approx. 13.3m² per 20L pail at two coats (1mm dry film) Recoat time 1 to 2 hours Ready for tiling 6 to 8 hours Flood test After 3 days Return to service 5 days VOC content 62g/L Shelf life 12 months from manufacture Use Interior and exterior, under tile, stone and other resilient finishes SafetyEven so, wear gloves and eye protection during application and keep the area ventilated, especially in enclosed spaces. Keep out of reach of children, avoid contact with eyes and skin, and do not let uncured product enter drains or waterways. Store the pail sealed, cool and out of frost. Refer to the Safety Data Sheet (SDS) for full details.
$266.99
Bastion Bond Breaker Waterproofing Joint Band is a 100mm wide, 10m long rubber reinforcing band for the most critical parts of a wet area waterproofing system, such as wall to floor junctions. It acts as the bond breaker in a liquid membrane system, so the membrane can cope with movement between two different surfaces instead of tearing at the join.About the bandThe band is made from a specialised grade of rubber that gives a rupture resistant seal and allows for the movement expected between abutting surfaces. It wets easily into the coats of a liquid membrane, which helps reinforce the finished membrane by improving puncture resistance and tensile strength. Because the band itself does the bond breaking, it removes the need for a separate bond breaker sealant at the joint, and installation is quick and straightforward. When used as part of a bond breaker system, it supports the requirements of AS 3740 (Waterproofing of domestic wet areas).Where to use itIndoors: wall to floor junctions in bathrooms, showers and laundries, and other critical joints in a wet area waterproofing system.Outdoors: Bastion's technical documentation lists the band as a bond breaker option within its membrane systems, but check the band's technical data sheet and your membrane's requirements before using it on external areas.It is designed to be embedded into Bastion liquid waterproofing membranes. Check your membrane's data sheet to confirm compatibility with other brands.How to use itMeasure and cut the band to suit each wall to floor junction. Apply a first coat of membrane, extending about 150mm up the wall and onto the floor, then embed the band into the wet membrane. Make sure the edges of the band are fully wetted out and there are no air bubbles behind it. Where lengths of band meet, overlap them by at least 50mm. If prefabricated corners are not being used, cut and fold the bottom leg of the band at corners and make sure it is fully bonded with the membrane. Then complete the membrane coats as set out in the membrane's data sheet.Important notesAlways follow the technical data sheet for the specific Bastion membrane you are using, including coat numbers and drying times. Surfaces should be properly prepared before the first coat goes on. Waterproofing in wet areas should be installed to the relevant Australian Standards and local requirements. If you are unsure, use a licensed waterproofer.Specifications Brand Bastion Product Bond Breaker Waterproofing Joint Band Size 100mm wide x 10m roll Pack 1 roll Material Rubber band Application Embedded by hand into wet liquid waterproofing membrane Minimum overlap at joins 50mm Standard Used as a bond breaker system to meet AS 3740 Use Wall/floor junctions and other movement areas in wet area waterproofing SafetyAlways read it and follow the instructions for the membrane you use with the band. Wear suitable protection when handling and installing it with liquid membranes, and store the roll clean and dry. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Gripset Betta Damp Stop is a one-part waterproofing primer and protective coating that helps hold back rising damp and moisture vapour moving through concrete, masonry and other porous mineral surfaces, supplied here in a 1L size. It suits renovators, tradies and confident DIYers who need a straightforward damp barrier under floor finishes, membranes and adhesives without mixing two parts together.About the formulaDamp Stop is a single-component, moisture-curing liquid in a light yellow colour. Because there is nothing to mix, you avoid the wasted product and short pot life that come with two-part epoxy primers. It is solvent free and odourless, so it can be used in confined areas. Once it has dried, it can be overcoated with other paints, coatings and adhesives. It also works as a dust-binding treatment for aged cement floors and dusty screeds.Where to use itIndoors: sealing the inside faces of cellar and basement walls against moisture vapour and dampness, priming floors ahead of membranes or finishes, protecting timber flooring, carpet and vinyl from rising damp, and stabilising dusty or aged screeds before floor finishes go down.Outdoors: priming external floors before a membrane is applied, and sealing the inner face of underground walls against residual moisture. The manufacturer lists it as suitable for internal, external, underground and immersed applications, and for resisting negative hydrostatic pressure.Suitable surfaces include concrete, cement mortar, renders and screeds, concrete and clay bricks, dense concrete, self-levelling compounds, compressed fibre cement sheet, fibre reinforced concrete, timber floorboards and sanded timber, and Hebel or other aerated concrete. For very porous, absorbent surfaces, or for metal and other smooth, shiny surfaces, the manufacturer points to other products in its range.How to use itStart with a clean surface, free of dirt, residues and old coatings. The surface can be damp but must have no surface water. Stir the product lightly, then apply with a short nap roller or short bristle brush. Leave 3 to 6 hours between coats and put the second coat on in the opposite direction to the first. Wait at least 24 hours, and make sure the primer is completely dry, before applying finishing membranes, coatings or adhesives.For high-build repairs, the manufacturer says to mix dry fine sand with the resin at about 3 parts sand to 1 part resin. Use a spatula for areas deeper than 1mm and keep the build to no more than 3mm.While still wet, tools can be cleaned with ethanol, methylated spirits or alcohol-based cleaners. Once dry, it has to be removed mechanically.Important notesDo not use over wet surfaces. Do not leave Damp Stop exposed as a finished membrane or sealer, as it is a primer. Do not apply when the surface temperature is below 10°C or above 35°C. Because it cures with moisture, cool or dry conditions can slow drying. The quoted drying times are tack free in 2 to 4 hours and dry film (ready to overcoat) in 24 hours, based on 20°C and relative humidity above 60%.Specifications Brand Gripset Betta Product Damp Stop Waterproofing Primer Size 1L Colour Light yellow Type One-component, moisture-curing liquid primer Solvent content Solvent free, odourless Application Short nap roller or short bristle brush Coverage (vapour barrier primer) About 6 to 8 m² per litre Coverage (negative pressure / moisture) About 3 to 4 m² per litre Coverage (dusty screeds, aged concrete) About 6 m² per litre Recoat time 3 to 6 hours between coats Tack free 2 to 4 hours Dry film (ready to overcoat) 24 hours Application temperature 10°C to 35°C surface Use Interior, exterior, underground and immersed SafetyEven so, avoid contact with eyes and skin, wear gloves and eye protection while applying, and keep it out of reach of children. Store the container sealed, away from direct heat and frost. Dispose of leftover product and empty containers in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$75.79
SikaGrout Deep Pour is a flowable, precision cementitious grout built for large sections and deep pours of up to 500mm, supplied here as a single 20kg bag. It suits machine bedplates, anchor bolts and other heavy grouting jobs where you need a high-strength, shrinkage-compensated fill that sets quickly and keeps developing strength.About the formulaA ready-mixed grout made from Portland cement, graded aggregates and Sika admixtures. It expands in two stages (Class A and C) to offset the shrinkage normally seen with Portland cement grouts. Sika lists shrinkage compensation, high early and 28-day strengths, good flow, adjustable consistency, good impact and thermal resistance, and no corrosion risk to steel or iron. It is lab tested to AS 1478.2. You mix it with water on site, and the consistency can be adjusted to suit the job.Where to use itIndoors: grouting machine bedplates, anchor bolts and crane rail soleplates in plant rooms, workshops and industrial buildings.Outdoors: mass grouting and concreting, bridge bearing pads and pre-cast concrete sections, with the curing precautions below.Designed for use with concrete and masonry structures, steel baseplates and anchor bolts.How to use itPrepare the substrate and formwork first, and check that the area is within the application temperature range. Mix the 20kg bag with clean water to the ratio on the Sika Product Data Sheet (about 2.5 to 2.8 litres per bag), then adjust within that range to reach the flow you need. Pour from one side of the void so air is pushed out rather than trapped. Place it in layers from 20mm up to 500mm in one pour. For depths over 500mm, Sika recommends adding clean, well-graded aggregate to reduce exothermic heat. Start curing straight away with plastic sheet, wet hessian or a liquid curing membrane to shield the grout from sun and wind. Clean tools and equipment with water while the grout is still wet. Hardened grout can only be removed mechanically.Important notesPot life is about 30 minutes at 20°C, so only mix what you can place in that time. Apply with air and substrate temperatures between 5°C and 35°C. Good curing is vital for final strength and for tight contact with the baseplate. Shelf life is 9 months in undamaged, sealed packaging stored dry and cool. Always follow the current Sika Product Data Sheet for mixing ratios and placement limits.Specifications Brand Sika Product SikaGrout Deep Pour Pack 20kg bag Colour Grey powder Base Portland cement with graded aggregates and admixtures Application Mixed with water and poured Layer thickness 20mm to 500mm per pour Mixing water About 2.5 to 2.8 litres per 20kg bag Yield About 9.8 litres of grout per 20kg bag Pot life About 30 minutes at 20°C Compressive strength About 12 MPa at 1 day and about 70 MPa at 28 days (AS 1478.2, 50mm cubes) Application temperature 5°C to 35°C (air and substrate) Standard Lab tested to AS 1478.2 Shelf life 9 months SafetyIt lists the product as causing skin irritation, causing serious eye damage, possibly causing an allergic skin reaction and possibly causing respiratory irritation. Avoid breathing dust, use in a well-ventilated area and wash skin thoroughly after handling. Wear gloves, eye protection and a suitable dust mask, and keep contaminated work clothing at work. If dust is inhaled, move to fresh air. Refer to the Safety Data Sheet (SDS) for full details.
$71.01
Sikalastic-1K (also labelled Sikalastic-1 Komponent) is a one-component, cement-based waterproofing membrane for wet areas, balconies, tanks and below-ground walls, supplied here in a 10kg pail that suits small to medium jobs. You only add water, then apply it by brush or trowel to form a flexible, crack-bridging, fibre-reinforced coating that protects concrete and prepares surfaces for tiling.About the formulaA fibre-reinforced mortar based on cement modified with alkali-resistant polymers, plus selected aggregates, fine fillers and additives. The consistency can be adjusted with the amount of water, so it can be made thinner for brushing or stiffer for troweling. It has good sag resistance on vertical surfaces, bonds well to concrete, cement mortars, stone and masonry, and can be applied on damp substrates. Sika lists it as meeting AS/NZS 4020 for products in contact with drinking water.Where to use itIndoors: bathrooms, showers and laundries before tiling with a cement-based tile adhesive; flexible protection of concrete tanks, basins and pipes; waterproofing walls and floors in basements against negative water pressure.Outdoors: terraces and balconies before tiling; swimming pools before tiling; external wall surfaces that will be backfilled in ground; protective coating for reinforced concrete exposed to freeze-thaw and carbon dioxide attack.Suitable substrates include concrete, cement mortars, stone and masonry. Substrates must be structurally sound and clean, and all joints and gaps must be sealed before coating.How to use itPrepare the substrate so it is sound and free of dust, oil and loose material, and seal any joints or gaps. Add water to the powder and mix with a low-speed mixer until smooth. For a 10kg pail, Sika's current data sheet gives about 3.0 litres of water for brush application and about 2.2 litres for trowel application. Apply in at least two layers: no more than about 1mm per layer by brush or 2mm per layer by trowel. Sika specifies a total dry film thickness of about 2mm for standard applications and 3 to 4mm for negative-pressure or immersed applications. When brushing, work in two directions, crosswise. Mixed material has a pot life of about 30 minutes at 20°C. Clean tools with water before the material sets; hardened mortar can only be removed mechanically.Important notesApply only when air and substrate temperatures are between 5°C and 35°C. The membrane must be completely hardened before tiling, overcoating or water contact. At 20°C, Sika's guide is about 2 days before tiling, painting with a water-based coating or immersion in water, and longer in cooler conditions (about 3 to 7 days at 10°C depending on the use). Allow about 15 days before contact with drinking water. Tile over it with a polymer-modified, cement-based tile adhesive from the Sika range. Times vary with temperature and humidity. Consumption depends on substrate roughness; as a guide, about 1.2kg per m² per mm of thickness. Store in the original sealed pail in cool, dry conditions and protect from water. Check the production date, as the current Sika data sheet gives a shelf life of 6 months. Always follow the current Sika product data sheet for your application.Specifications Brand Sika Product Sikalastic-1K (Sikalastic-1 Komponent) one-component cementitious waterproofing mortar Pack 10kg pail Colour Light grey Base Cement modified with alkali-resistant polymers, with fibres Application Brush or trowel (mix with water) Pot life About 30 minutes at 20°C Application temperature 5°C to 35°C (air and substrate) Fresh mortar density About 1.5 kg/L Consumption About 1.2 kg/m² per mm (guide) Water contact About 2 days at 20°C before immersion; about 15 days before drinking water contact Approvals AS/NZS 4020 (contact with drinking water) Use Interior and exterior SafetyWet and dry cement products can cause serious eye damage, so wear safety glasses or a face shield, protective gloves and long sleeves, and avoid breathing dust when handling and mixing. For skin contact, remove contaminated clothing and wash with soap and water. Keep out of reach of children, and do not eat, drink or smoke while using it. Refer to the Safety Data Sheet (SDS) for full details.
$137.46
Sika MonoTop-352 NFG is a lightweight, high-build structural repair mortar for damaged and spalled concrete, supplied here as a 20kg bag in grey powder form. It is a one-component, polymer-modified, fibre-reinforced mix with a built-in corrosion inhibitor, and it meets Class R3 of EN 1504-3. It suits both hand application and wet-spray machine application.About the formulaThe mortar is based on sulphate resistant cement, selected lightweight aggregates, a corrosion inhibitor and polymer modification. Sika describes it as low shrinkage, low permeability and sulphate resistant. The low density makes it easier to build up thickness while still being suitable for structural repair. On a well prepared, roughened substrate a bonding primer is generally not needed, even when applying by hand. It can also be used as a repair mortar before Sikagard 62 and 63N coatings, and it is compatible with the Sika FerroGard sacrificial anode system.Where to use itIndoors: repairing spalled or damaged concrete in buildings, including structural elements and superstructure works.Outdoors: repairing concrete in bridges and other infrastructure, and restoring cover over reinforcement where concrete has been contaminated or carbonated.Suitable for concrete repair, including restoration work and structural strengthening as set out in EN 1504-9. Layers can be built from 4mm up to 75mm in a single application.How to use it Prepare the area first. Remove loose, contaminated and deteriorated material and clean any exposed reinforcement of rust, scale and dust. Roughen the substrate using abrasive blasting or high pressure water-blasting. Pre-wet the prepared substrate about 2 hours before application and keep it in a saturated surface dry (SSD) condition. Pour 2.8 to 3.3 litres of clean water into a suitable container for each 20kg of powder. Add the powder while stirring slowly. Mix thoroughly for at least 3 minutes, using a low speed drill mixer (under 500 rpm) or a forced-action mixer for machine application. Small amounts can be mixed by hand. Apply by trowel, pressing the mortar firmly onto the substrate, or by wet-spray equipment. Finish once the mortar begins to stiffen. Protect the fresh mortar straight away from premature drying using a suitable curing method, such as a curing compound, damp geotextile or polythene sheet. Important notesApply only to sound, properly prepared substrate. Do not exceed the recommended water dosage, and do not add extra water while finishing, as this can cause discolouration and cracking. Avoid application in direct sun or strong wind, and protect freshly applied material from freezing. The recommended ambient and substrate temperature range for application is +5 °C to +30 °C. Final set is about 6 hours. For critical or structural repairs, follow the current Sika Product Data Sheet and the Sika method statement for concrete repair.Specifications Brand Sika Product MonoTop-352 NFG Structural Repair Mortar Pack 20kg bag Colour Grey powder Base Sulphate resistant cement, corrosion inhibitor, lightweight aggregates, polymer modified Application Hand (trowel) or wet-spray machine Layer thickness 4mm minimum, 75mm maximum per layer Mixing water 2.8 to 3.3 litres per 20kg Yield About 12.8 litres of mortar per 20kg Consumption About 15.6kg of powder per cm thickness per m² Fresh mortar density About 1.8 kg/l Maximum grain size 2mm Final set About 6 hours Standard Class R3 of EN 1504-3 Shelf life 12 months in unopened, undamaged packaging, stored dry and cool Use Interior and exterior concrete repair SafetyThis is a cement-based powder. Hazards include skin irritation, possible allergic skin reaction, serious eye damage and respiratory irritation. Avoid breathing dust, use in a well-ventilated area, and wear protective gloves and eye or face protection. Wash skin thoroughly after handling and do not wear contaminated work clothing out of the workplace. Refer to the Safety Data Sheet (SDS) for full details.
$100.25
Dingo Structural Mortar Repair is a polymer-modified, fibre-reinforced repair mortar for restoring damaged concrete and masonry, supplied here as a single 10kg bag of dry powder. It is a ready-to-mix, one-component product that you simply combine with clean water, and it is built for structural-grade repairs on both horizontal and vertical surfaces, above or below ground.About the formulaThis is a lightweight, low-shrinkage, cement-based mortar that is modified with polymers and reinforced with fibres to help limit micro cracking. According to the manufacturer it meets the requirements of class R3 under EN 1504-3. The powder is based on sulphate resistant cement, selected lightweight aggregates and additives, and it gives repairs better resistance to oils, sewage and chemicals. It can be built up in layers of up to 75mm thick.Where to use itIndoors: patching cavities, voids and honeycombed areas in concrete or mortar, and repairing brickwork.Outdoors: repairing spalled concrete caused by corroding reinforcement, and fast repairs to horizontal or vertical concrete and mortar surfaces above and below ground level. The manufacturer also lists building, bridge and infrastructure repair work and structural strengthening among its uses.Suitable substrates include concrete, mortar, brick and block masonry that is clean, sound and free of oil, grease and loose material.How to use itLay out your tools before you start. Pour the amount of powder you need into a clean bucket and add clean water gradually. A full 10kg bag needs roughly 1.6 to 1.7 litres of water. Mix mechanically for at least 3 minutes using a low-speed drill and paddle mixer until the mix is consistent. Use the mixed material as soon as possible after opening the bag. Apply it to the prepared surface by hand or by mechanical methods.Important notesMix only what you can use promptly, and only with clean water. One 10kg bag yields roughly 6.5 litres of mortar. How much you need depends on how rough the surface is and how thick the layer is. Keep unopened bags in a cool, dry, sheltered place out of harsh weather. For large, load-bearing or engineered structural repairs, check the manufacturer's Product Data Sheet and get advice from the manufacturer or a qualified engineer.Specifications Brand Dingo Product Structural Mortar Repair Pack 1 x 10kg bag Form / colour Powder, grey Base Polymer-modified, fibre-reinforced cementitious mortar (sulphate resistant cement) Application Mix with water; apply by hand or mechanically Mix water About 1.6 to 1.7L per 10kg bag Yield About 6.5L of mortar per 10kg Maximum layer thickness 75mm Standard Class R3 of EN 1504-3 Use Interior and exterior SafetyThis is a cement-based powder. Mixing it may irritate the eyes and skin, and prolonged contact can cause dermatitis and alkaline burns. The dust irritates the eyes, skin and respiratory system. Avoid contact with the eyes and skin, wear protective clothing, gloves and eye protection, and wear a suitable dust mask when handling the dry powder. Refer to the Safety Data Sheet (SDS) for full details.
$33.82
Davco Lanko 752 Bondit is a white PVA emulsion that does three jobs on site: it works as a mortar additive, a primer and a sealer, and it can also bond timber to timber. This 5L pack suits renderers, tilers, concrete patchers and joiners who want one economical product for strengthening cement-based work. Mixed into sand and cement mixes, it lifts adhesion, flexibility, tensile strength and impact resistance. It also improves the flexural and compressive strength of the mortar.About the formulaBondit is a PVA-based emulsion supplied ready to use, and you add it to your mix or dilute it with water depending on the job. Beyond strengthening mortars, it can be thinned and applied to concrete to prime, dustproof and seal the surface. Used neat, it can also be applied to timber joints as a PVA wood bond.Where to use itMortar additive: sand and cement mixes for concrete patching and for rendering, and mortars for tiling over concrete, render, blockwork and rendered brickwork.Bonding slurry: mixed into neat cement to bond new sand and cement toppings onto concrete.Primer and sealer: diluted with water and brushed or rolled onto concrete to prime, dustproof and seal.Joinery: applied neat to bond timber to timber.Suitable surfaces include concrete, render, blockwork, rendered brickwork and timber. Very porous surfaces should be primed with Bondit first. Always test for suitability on a small area before starting the full job.How to use itSurfaces should be dry, structurally sound and clean, and free of dust, dirt, wax, oil, grease, paint, adhesives and other contaminants. New concrete needs to cure for six weeks and have a wood float finish. Steel-trowelled concrete should be acid etched or wire brushed before tiling. New render should cure for at least 7 days.As a mortar additive, the manufacturer's guide is approximately 750 mL to 1 L of Bondit, plus the required water, for each 20 kg of sand and cement mix.As a primer, dilute with water and apply by brush or roller. Expect roughly 6 to 8 m² per litre when diluted.For joinery, apply neat by brush or roller. Expect roughly 3.5 m² per litre, depending on surface porosity and site conditions.Important notesDo not use Bondit in temperatures above 40°C or below 5°C.It is not suitable for permanently wet or damp areas such as swimming pools and spas. For those installations, the manufacturer recommends Davco Lanko 751 Lankolatex instead.Coverage figures are approximate and vary with surface porosity and site conditions.Store in the original, unopened and undamaged packaging in dry conditions between 4°C and 35°C. Shelf life is 12 months.Specifications Brand Davco (Lanko range) Product Lanko 752 Bondit PVA Additive Pack 5L Colour White Base PVA (polyvinyl acetate) emulsion Application Mixed into mortar, or applied by brush or roller Coverage (neat, joinery) Approximately 3.5 m² per litre Coverage (diluted, priming) Approximately 6 to 8 m² per litre Mortar dosage Approximately 750 mL to 1 L per 20 kg sand and cement mix Application temperature 5°C to 40°C Shelf life 12 months, unopened Storage Dry, 4°C to 35°C, original sealed packaging SafetyUse with adequate ventilation, and wear chemical-resistant gloves when handling. Do not eat, drink or smoke while using it, and follow standard hygiene practice. Keep the container tightly closed in a dry, well-ventilated place. Refer to the Safety Data Sheet (SDS) for full details.
$78.10
Davco Ultraflex is a premium grade, cement-based tile adhesive for walls and floors, supplied here as a 20kg bag for full tiling jobs. It is rubber modified, so it suits both rigid and flexible substrates, and it is rated for commercial work as well as home renovations.About the formulaA powder adhesive that you mix with clean water and apply with a notched trowel. The rubber modification gives it extra flexibility over framed and sheet substrates. It is suitable for use over early age screed (cured for 24 hours) and over under-tile heating. It is classified C1S1E under AS ISO 13007 and has a low VOC content of 5 g/L (SCAQMD method 304-91).Where to use itIndoors: living and dining areas, walkways and office spaces, on both walls and floors.Outdoors: external verandahs and decks, on both walls and floors.Suitable tiles include porcelain, ceramic, mosaic, terracotta, slate, quarry, granite and marble. Suitable substrates include cement render, blockwork and rendered brickwork, plasterboard, fibre cement sheet, compatible waterproofing membranes, timber floors (with fibre cement tile underlay installed), new concrete (cured for 7 days) and new screed (cured for 24 hours). The adhesive is not suitable for translucent tiles or for moisture sensitive stone such as green marble.How to use itMake sure the substrate is sound, firmly fixed, clean and free of dust, oil and loose material. Prime the surface where the data sheet calls for it (for example plasterboard, fibre cement sheet, screed and timber floors with tile underlay), using the Davco primer the manufacturer recommends for that substrate. Mix the powder with clean potable water to a smooth, lump-free consistency, about 7 litres of water per 20kg bag. Spread the adhesive with a notched trowel suited to your tile size and press the tiles firmly into place. A 20kg bag covers about 12m2 when applied with a 6mm notch trowel, and less with larger trowels. Clean tools with water while the adhesive is still fresh, and wipe wet adhesive off tile faces with a damp cloth. Cured adhesive is much harder to remove.Important notesAllow 6 to 8 hours before grouting. Check the manufacturer's data sheet for substrate preparation, primers and movement joint requirements before you start. Store unopened bags off the ground in cool, dry conditions. Shelf life is up to 12 months when stored this way. If you plan to use it on a surface or in an application not covered by the data sheet, contact the manufacturer first.Specifications Brand Davco Product Ultraflex Premium Grade Cement-Based Tile Adhesive Pack 20kg bag Base Cement-based, rubber modified powder Application Mixed with water, applied by notched trowel Coverage About 12m2 per 20kg bag (6mm notch trowel) Time before grouting 6 to 8 hours Classification C1S1E (AS ISO 13007) VOC content 5 g/L (low VOC) Use Interior and exterior, walls and floors, commercial and domestic SafetyThis product contains cement, which is alkaline and can cause dermatitis. Wear PVC or similar gloves and safety goggles when mixing and applying. Avoid breathing in the dust when opening bags and mixing, and use suitable dust protection where needed. Wash skin with water after contact. Refer to the Safety Data Sheet (SDS) for full details.
$40.69
Bastion Mastic Tile Adhesive is a white, cement-based powder adhesive for fixing wall and floor tiles, supplied here in a 20kg bag for larger tiling jobs. It is a non-slump mix, so tiles stay where you put them on vertical surfaces. It suits both interior and exterior tiling.About the formulaA cement-based powder that you mix with clean water to a thick, creamy, lump-free mortar. The non-slump body helps tiles hold their position on walls. The manufacturer data sheet lists an open time of 15 minutes and an adjustment time of 20 minutes. Site conditions affect these times, so only spread as much adhesive as you can tile before it skins over.Where to use itIndoors: wall and floor tiling over concrete, renders and screeds.Outdoors: external wall and floor tiling on the same types of substrate.Suitable tile types listed by the manufacturer are ceramic tiles, porcelain, glass mosaics and natural stone (excluding moisture-sensitive stone). Suitable substrates are concrete, renders and screeds.How to use itAdd the powder to clean water in a large, clean container while stirring vigorously with a paddle mixer. A 20kg bag needs about 6 litres of water. Mix for several minutes, leave it to stand for five minutes, then remix. As a general guide, use a notched trowel of at least 6 x 6 x 6mm on walls and at least 10 x 10 x 10mm on floors. The adhesive can be applied at a bed thickness of more than 3mm and less than 10mm. Check that there are no voids under the tile and do not spot fix.Important notesNot suitable for moisture-sensitive or dimensionally unstable natural stone. Coverage varies with substrate condition, tile type and technique. As a guide, a 20kg bag covers about 10m2 on walls with a 6mm notched trowel, or about 7m2 on floors with a 10mm notched trowel. Always check the current data sheet and SDS for shelf life, curing and grouting times, and any limits for your tile and substrate.Specifications Brand Bastion Product Mastic Tile Adhesive Powder Pack 20kg bag Colour White / off white Base Cement-based powder, non-slump Mixing ratio About 6 litres of water per 20kg bag Application Notched trowel Open time 15 minutes Adjustment time 20 minutes Bed thickness More than 3mm and less than 10mm Coverage (20kg) About 10m2 on walls (6mm trowel), about 7m2 on floors (10mm trowel) Use Interior and exterior, walls and floors SafetyThe manufacturer notes that this product may cause skin irritation and an allergic skin reaction. It may also cause serious eye injury and irritation of the respiratory system. Wear protective gloves and eye protection, and avoid breathing the dust when handling the dry powder. Refer to the Safety Data Sheet (SDS) for full details.
$28.62
You have seen 192 out of 458 products
Find products tagged for use on concrete. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on concrete surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
