Turbo Builders Bog Hardener is the red catalyst paste that turns Turbo Builders Bog and other polyester body fillers from a workable putty into a hard, sandable repair, supplied here in a 40g pack. You control how fast the filler sets by adjusting how much hardener you add, so you can slow things down for a big fill or speed them up on a cold day.About the formulaA red paste made from 50% benzoyl peroxide in an emulsion base, designed as the second component for Turbo Builders Bog and body fillers. Once it is mixed through the filler, it starts a chemical reaction that cures the repair from the inside out. Turbo also positions its red hardener for use with its Concrete Bog and Metal Bog, and for other polyester fillers.Where to use itIndoors: repairing timber architraves, door frames, skirtings, window sashes, benches and furniture with Turbo Builders Bog.Outdoors: rebuilding rotted window sills, door bases and weatherboards, and filling dents in vehicle panels with polyester body filler.Use it with Turbo Builders Bog, Turbo Concrete Bog, Turbo Metal Bog and other polyester body fillers. The hardener is not a stand-alone product, so it is always mixed into a compatible filler.How to use itPrepare the repair area first. For timber, it should be clean, dry, unpainted, roughened and free of rot. Scoop out the amount of filler you need onto a clean, flat, non-absorbent surface, add the hardener, and mix thoroughly until the colour is completely uniform with no white or red streaks. As a guide from Turbo's mixing directions for Builders Bog, about 2.5g of hardener to 100g of filler gives a gel time of roughly 7 minutes at 22°C. Use more hardener in cold weather or for a faster set, and less in hot weather or when you need more working time. Always stay within the mixing range printed on your filler's tin or pack. Apply the mix promptly with a flat spreader. Once it gels to a firm, cheese-like stage you can trim, grate or shape it. Allow it to cure fully, then sand and paint.Important notesMixing ratios and set times vary with temperature, the amount mixed and the thickness of the fill, so mix small test batches if you are unsure. Warmer conditions need less hardener for the same set time. Too little hardener can leave the filler soft or slow to cure, so do not go below the range on the filler's directions. Once hardener is mixed in, the filler cannot be re-softened, so only mix what you can apply in the working time.Specifications Brand Turbo Product Builders Bog Hardener (Red Hardener) Pack 40g Colour Red Base 50% benzoyl peroxide paste (emulsion) Application Mixed by hand into polyester filler Example gel time About 7 minutes at 22°C (2.5g per 100g Builders Bog) Compatible with Turbo Builders Bog, Concrete Bog, Metal Bog and other polyester fillers Use Interior and exterior repairs (via the filler) SafetyUse with normal care: work in a well-ventilated area, keep away from heat and open flame, and wear gloves and safety glasses to avoid contact with eyes and skin. Keep it out of reach of children, store it in a cool, dry place with the cap tightly closed, and keep it separate from other chemicals. Refer to the Safety Data Sheet (SDS) for full details.
$8.45
Davco Lanko 136 Rapid Patching Mortar is a fast-setting, cement-based repair mortar for patching concrete, brickwork and rendered surfaces, supplied here in a 5kg bag that suits small to medium repairs. It gains strength very quickly, so floor finishes, underlayments and coatings can go over the repair in a fraction of the time that a standard patching mix needs.About the formulaA one-part, pre-blended grey powder made from cement, selected aggregates and special additives. It is polymer modified, so you only add clean water. Davco describes it as shrinkage compensated to help resist cracking as it cures, with a fine, workable finish. It sets rapidly and develops very high early strength, and the manufacturer lists it as freeze/thaw resistant once cured. It is not a vapour barrier.Where to use itIndoors: patching holes, chips and defects in concrete floors before levelling compounds, underlayments, carpet, vinyl or ceramic tiles go down; forming small ramps or transitions before floor coverings; treating chamfers, coves and seams before waterproofing membranes or epoxy coatings.Outdoors: repairing concrete slabs, pillars and posts; patching brickwork and rendered walls before tiling, coating or painting.Suitable materials include concrete, brick, block, masonry and cement render. Always apply it to a sound, properly prepared surface.How to use itRemove dust, loose material, oil, grease and anything else that could stop a bond. Dense, power-floated concrete may need a bonding primer or moisture barrier first, so check the Davco data sheet for the recommended options. Mix with clean potable water only, at about 0.53 to 0.6 litres per 5kg bag. Add the powder to most of the water while mixing, then adjust to a workable consistency with a drill and paddle or by hand. Mix only what you can place within roughly 15 minutes. Press a first pass firmly into the surface with a steel trowel, build up to the required thickness, then finish with a wet steel trowel or foam float. Do not vibrate the mortar into place, and discard any mix that starts to stiffen.Important notesDo not apply in direct sun or strong winds, and keep the air and surface temperature at or above 7°C. Do not feather edge this mortar. It is a repair material and not a wearing surface, so cover it where it will be exposed to wear. The manufacturer's guide is that floor finishes and underlayments can go on after about 90 minutes. Foot traffic is possible in about 45 minutes at 23°C, and epoxy coatings can go on from about 4 hours (do an on-site test first). Deeper or heavy-load repairs need extra care and cure time, so follow the data sheet. Strength figures vary with the aggregates and site conditions.Specifications Brand Davco (Lanko range) Product Lanko 136 Rapid Patching Mortar Pack 5kg bag Colour Grey powder Base Cementitious, polymer modified Application Mixed with water, applied by steel trowel Mixing ratio About 0.53 to 0.6 L water per 5kg bag Yield About 2.5 L per 5kg bag Compressive strength About 13 MPa at 1 hour, about 80 MPa at 28 days (23°C) Ready for floor finishes From about 90 minutes Storage Sealed, dry, between 5°C and 35°C Use Interior and exterior SafetyAvoid breathing dust, and wear gloves, protective clothing and eye or face protection. Remove contaminated clothing and wash it before reuse. If it gets on skin, wash with plenty of water. Store the sealed bag dry and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$34.72
Dingo Fire Rated Mortar is a ready-to-mix, rapid setting cement mortar made for the high heat areas of pizza ovens, fireplaces and barbeques, supplied here as a 10kg bag. It suits both new builds and patch repairs, so you can use it to build a heat-exposed structure or to fix up an existing one.About the formulaA cement-based dry mix made from high temperature resistant alumina cement and graded aggregates. You only add clean water, and no other components are needed. The manufacturer rates it for heat resistance up to 800°C, referencing AS 1530.1:1994 (R2016). Once mixed, it sets quickly: the initial set takes about 2 hours and the final set about 3 hours.Where to use itIndoors: fireplaces and chimneys, including building them and patching existing masonry.Outdoors: pizza ovens and barbeques, both new construction and repairs to existing structures.It is intended for masonry heat-zone work such as pizza ovens, barbeques, fireplaces and chimneys. For any other material or use, check with the manufacturer first.How to use itLay out your project and have all your tools ready before you open the bag. Make sure surfaces are clean, sound and free from oil, grease and loose particles. Tip the amount you need into a clean bucket, then add clean water gradually. A 10kg bag needs roughly 1.6 to 1.7 litres of water. Mix mechanically for at least 3 minutes, using a low speed electric drill with a paddle mixer, until the mix is thorough and even. Use the contents as soon as you can after opening the pack. A 10kg bag makes roughly 6 to 6.5 litres of mortar.Important notesMix only what you can use within the setting window, as the mortar begins to set after about 2 hours. The bag holds 10kg net of dry product, so take care when lifting it. Poor manual handling can cause injury. Prolonged skin contact with the wet mix may cause irritation, dermatitis or alkaline burns.Specifications Brand Dingo Product Fire Rated Mortar Pack 10kg bag (dry powder) Colour Grey Base Cement based (alumina cement and graded aggregates) Application Mix with water and apply as mortar for new construction or patching Mixing water About 1.6 to 1.7L per 10kg bag Yield About 6 to 6.5L of mortar per 10kg Set time Initial set 2 hours, final set 3 hours Heat resistance Up to 800°C Standard referenced AS 1530.1:1994 (R2016) Use Pizza ovens, fireplaces, barbeques and chimneys SafetyThe wet mix can irritate the eyes and skin, and the manufacturer notes that prolonged exposure may cause dermatitis and alkaline burns. Avoid contact with eyes and skin, and take care when handling the 10kg bag. Refer to the Safety Data Sheet (SDS) for full details.
$44.31
Dingo Fast Set Mortar is a ready-blended, quick-setting mortar for small masonry repairs around the home and on the building site, supplied here in a handy 3kg bag. Just add water to turn the dry mix into a workable mortar for patching, repointing and other quick fix-up jobs, with a set time of around 15 minutes.About the formulaA dry, pre-mixed blend of cement, sand and additives, so there is no need to source and proportion separate materials for a small repair. Dingo describes it as a smooth, buttery mortar, and it cures to a grey finish. The 3kg pack suits small jobs where a full bag of general mortar would be wasted.Where to use itIndoors: small patches and repairs to masonry or brickwork where a quick turnaround matters.Outdoors: repairs to brick and render walls, repointing brickwork, grouting and patching around the home and on building sites.Suitable for brick, block and stone laying and for masonry and render repairs.How to use itLay out your project and have your tools ready before you start, because the mortar sets quickly. Tip the amount you need onto a clean surface or into a wheelbarrow or mixing tub, then add clean water gradually while mixing thoroughly to a stiff consistency. If you add too much water, leave the mix aside until it thickens back to a workable consistency. Trowel the mortar onto your bricks or blocks. Lightly soak clay bricks in water before laying, and lay concrete blocks dry. Mix only what you can use quickly, and use the contents soon after opening the bag.Important notesKeep the mortar damp for about a week after application to help it harden. Retaining walls should not be backfilled for at least two weeks. Keep the dry mix and any unused product dry before use. The amount of water needed is stated differently across published sources, so follow the directions printed on your bag and add water gradually.Specifications Brand Dingo Product Fast Set Mortar Pack 3kg bag Colour Grey Base Cement and sand pre-mix with additives Application Mix with water, apply by trowel Set time About 15 minutes Curing Keep damp for about one week Use Masonry, brick and render repairs, repointing, grouting and patching SafetyAs with all cement products, mixing it may irritate the eyes and skin. Cement dust can irritate the eyes, skin and respiratory system, and prolonged skin contact may lead to dermatitis or alkaline burns. Wear gloves, eye protection and suitable protective clothing, avoid breathing in dust (use a dust mask when needed) and wash skin thoroughly after handling. Store in a dry place. Refer to the Safety Data Sheet (SDS) for full details.
$6.57
Sika Sikasil Auto is a neutral-cure, one-component silicone adhesive sealant made for vehicle repair and trim work, supplied here in a handy 75g tube. It forms a permanent, flexible bond or seal on a wide range of automotive materials, and the cured rubber copes with sunlight, salt spray, temperature swings, vibration and regular car-wash products without hardening, shrinking or cracking.About the formulaA moisture-curing, one-component silicone with a neutral cure, so it does not give off the acidic smell of acetic silicones and is described by the manufacturer as non-corrosive. It cures by reacting with moisture in the air, starting at the surface and working into the core of the joint. Cure speed depends on humidity and temperature, and it cures more slowly in cold conditions. Once cured it is a soft, stretchy rubber with strong thermal, UV, weathering and vibration resistance, and it stays serviceable from -50°C up to 250°C.Where to use itIndoors: bonding small interior components and trim, sealing joints, and cutting down noise and vibration inside the vehicle.Outdoors: sealing and bonding small exterior parts and joints on cars and other vehicles where weather, UV and salt spray are a concern.Suitable materials include fibreglass, metals, most plastics, glass and painted surfaces. Always test on the actual substrates and under your real conditions first to confirm adhesion and material compatibility.How to use itApply at ambient temperatures between 5°C and 45°C onto clean, dry surfaces that are free of oil, grease and dust. Run the sealant into the joint or onto the part and assemble or tool it before it skins over. At 23°C and 50% relative humidity it skins in about 10 minutes and is tack free in about 20 minutes. Excess uncured sealant can be wiped off with Sika Remover-208 or a similar product. Cured sealant has to be trimmed or scraped away mechanically. If you get it on your skin, wash straight away with SikaCleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.Important notesSikasil Auto cannot be overpainted, so complete any painting before sealing or mask the area. It cures to a depth of about 3 mm in 24 hours, so deeper joints and thicker beads take longer. Check the manufacturer's data sheet for any surfaces or applications where the product is not recommended. This product is designed for vehicle applications. Test first on a small area before committing to the full job.Specifications Brand Sika Product Sikasil Auto Multipurpose Automotive Adhesive Sealant Pack 75g tube Colour Translucent Chemical base 1-component silicone, neutral cure, moisture-curing Application Tube, applied by hand Application temperature 5 to 45°C ambient Skin time About 10 minutes (23°C, 50% r.h.) Tack free time About 20 minutes (23°C, 50% r.h.) Cure speed About 24 hours to a 3 mm depth Density (uncured) 1.0 kg/L Shore A hardness 30 Tensile strength 1.0 N/mm² Elongation at break 600% Service temperature -50 to 250°C Shelf life 18 months when stored below 25°C Use Vehicle interior and exterior SafetyFollow normal good practice for silicone sealants: work in a well-ventilated area, wear gloves and eye protection, and keep out of reach of children. Wash skin promptly after contact using an industrial hand cleaner and water, and do not use solvents on skin. Store in the original sealed tube below 25°C. Refer to the Safety Data Sheet (SDS) for full details.
$17.37
Gyprock Pro-Repair 10 is a fast-setting, plaster-based jointing and patching compound, supplied here as an 8kg bag for small jointing jobs and everyday wall and ceiling repairs. It gives you roughly ten minutes of working time once mixed, so you can fill, tape and move on without waiting for a slow-drying compound to dry. It suits tradies, renovators and keen DIYers who want quick results.About the formulaPro-Repair 10 is a lightweight, low-VOC powder that you mix with water. It is a setting compound, so it hardens by chemical reaction rather than by evaporation. It is tinted so repairs are easy to spot on painted surfaces. It is designed to stick well to jointing tape, to shrink very little, and to sand easily as a topcoat. You can use it for every coat of a three-coat joint or as a base coat only. If you use it for all three coats with an open-weave fibreglass tape such as FibaFuse, you can sand the topcoat on the same day once it has dried enough. It is made in Australia by CSR Gyprock.Where to use itIndoors: patching holes, nicks, cracks and other defects in new and existing plasterboard walls and ceilings, and jointing smaller residential or commercial rooms.Fibre cement: suitable for repairs and jointing on Cemintel fibre cement sheet as well as Gyprock plasterboard.Suitable surfaces are Gyprock plasterboard and fibre cement. It is not recommended for wet areas.How to use itStart with a clean, dust-free surface. Tear the bag open at a top corner and mix with clean water as directed on the pack. Because the working time is short, mix only as much as you can use in one go. Apply by hand with a knife or similar tool. Embed the jointing tape in the base coat, then add further coats as needed. Let the compound dry fully, then sand the topcoat smooth before you prime and paint. Throw away any mixed compound you have not used. Keep unused powder in its original bag with the top rolled down, inside an airtight container.Important notesPro-Repair 10 is a setting compound, so you cannot rework it once it has started to set. Do not add water to extend the working time. It is not recommended for wet areas. Shelf life is one year from the date of manufacture, so store the bag somewhere dry and out of the weather and direct sun. Allow enough drying time before sanding, even when you are finishing the job on the same day.Specifications Brand Gyprock (CSR) Product Pro-Repair 10 Jointing and Patching Compound Pack 8kg bag Form Dry powder, mix with water (not pre-mixed) Base Lightweight plaster-based setting compound Application Hand applied Working time About 10 minutes after mixing Setting time About 30 minutes Coverage About 13kg per 100m² Suitable surfaces Plasterboard and fibre cement Shelf life 1 year from manufacture Standard Used in line with AS/NZS 2589 (Gypsum linings, application and finishing) Origin Australian made SafetyDust can irritate the eyes and may aggravate existing eye conditions, so avoid breathing dust and avoid eye contact and prolonged skin contact. Wear gloves, eye protection and a dust mask when mixing and sanding. In case of eye contact, flush thoroughly with running water for 15 minutes with the eyelids held open. Store in a cool, dry, well-ventilated place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$50.21
Turbo Metal Builders Bog is a two part, aluminium and glass fibre reinforced polyester filler for rusted metal, dents, cracks, holes and tears, supplied here as a 500ml can. It is aimed at panel beaters, builders and DIYers who want a hard, workable repair that can go over or under ordinary body filler for extra strength, and which also works on fibreglass, wood, stone, concrete and aluminium.About the formulaThe filler is a paste based on unsaturated polyester resin in styrene, loaded with aluminium so you can repair metal with a metal-filled compound, and with glass fibre strands that help bridge holes and gaps. Once catalysed with a separate peroxide-based hardener, the mix gels to a cheese-like consistency that can be cut, shaped or pared, then cures hard. Changing the amount of hardener lets you speed up or slow down the set to suit the job and the weather. Turbo describes it as having minimal shrinkage, good stress resistance and flexibility, water resistance and rust-inhibiting properties.Where to use itIndoors: repairing holes, cracks and damaged areas in fibreglass, wood, stone and concrete, and filling larger voids where a standard filler would sag or shrink.Outdoors: rusted-out panels, dents and holes in metal, vehicle bodywork and similar repairs, plus cracked or broken concrete, masonry and aluminium items exposed to weather.Suitable materials include steel and other metals, aluminium, fibreglass, wood, stone, concrete and masonry. It can be used instead of, or underneath, regular plastic body filler.How to use itStart with a clean, dry, sound surface, free of loose rust, paint, oil, grease and dust, and roughen smooth surfaces for a better key. Work out how much filler you need and mix it with the hardener following the directions on the can, stirring until the colour is completely uniform. Because cure speed depends on temperature and the amount of hardener, try a small batch first. Press the mix firmly into the repair, building up and shaping it while it is still soft. Once it has gelled you can trim it, then sand, file, drill, machine and paint it after it has cured hard.Important notesThis is a two part system and will not cure without the hardener, so check the hardener is on hand before you start. More hardener or warmer conditions will shorten the working time, and less hardener will lengthen it. Full cure is typically within about 30 to 60 minutes, and the repair can be painted within the hour, though times vary with temperature and mix. The cured filler is paintable but not stainable. For large structural repairs on metal, make sure the underlying area is sound.Specifications Brand Turbo Product Metal Builders Bog (metallised repairer) Size 500ml can Colour Grey Base Unsaturated polyester resin filler with aluminium and glass fibre Application Hand applied after mixing with hardener Set and cure Gels to a cheese-like consistency, full cure typically about 30 to 60 minutes (varies with hardener and temperature) Paintable Yes, within the hour Sandable Yes Stainable No Shrink resistant Yes UV resistant Yes Use Interior and exterior SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use outdoors or in a well-ventilated area, avoid breathing vapours, and avoid contact with eyes, skin and clothing. Wear suitable gloves and eye protection. Wash exposed skin thoroughly after handling and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details.
$32.41
Stanley Dual Temp Mini Glue Sticks are all-purpose hot melt glue sticks for 7mm mini glue guns, supplied here as a 24-pack of 100mm sticks for craft, hobby and household jobs. They are made for mini hot melt, low temperature and dual temperature guns, so you can bond delicate, heat-sensitive materials as well as everyday items.About the formulaA thermoplastic hot melt adhesive based on ethylene vinyl acetate (EVA) and petroleum resin, with no solvents to evaporate. Because it is a dual melt formula, it can be run on a low heat setting for materials that would be damaged by high heat, or on a high heat setting for harder, non-porous surfaces. The glue sets quickly as it cools, usually within about 15 to 30 seconds.Where to use itLow temperature setting: paper, ribbon, foam and other delicate or heat-sensitive materials in craft and hobby projects.High temperature setting: china and leather, and general household repairs and fastening jobs.Suitable materials include paper, cardboard, leather, china and other non-porous surfaces, and heat-sensitive craft materials such as polystyrene foam, ribbon and dried flowers. Test on a small, hidden area first if you are unsure how a material will react to heat.How to use it Check that your glue gun takes 7mm mini glue sticks. These sticks are not compatible with standard 11mm glue guns. Make sure surfaces are clean, dry and free of dust and grease. Load a stick into the gun and let it heat fully. Choose the low setting for delicate materials or the high setting for china, leather and other non-porous surfaces, if your gun has a temperature switch. Apply the glue to one surface, press the parts together straight away and hold them still until the glue sets. Unplug the gun and rest it safely when you finish. Important notesWork quickly, as hot melt glue starts to set within seconds of application. Molten glue and the gun nozzle can cause burns, so keep them away from skin and children. Hot melt adhesive is not designed for heavy structural loads or for surfaces that stay hot, because the bond can soften when reheated. Glue guns are sold separately.Specifications Brand Stanley Product Dual Temp Glue Sticks (Dual Melt Mini) Model number 1-GS10DT Pack 24 sticks Stick size 7mm diameter x 100mm length Colour White Base Thermoplastic hot melt (EVA and petroleum resin) Application Mini hot melt, low temperature and dual temperature glue guns Set time About 15 to 30 seconds Use Craft, hobby, household and general fastening SafetyThe main hazard is thermal burns from molten glue, which can cause intense pain and tissue damage. Avoid breathing fumes from heated glue and use the gun in a well-ventilated area. If it gets in the eyes, flush with water while holding the eyelids open and seek medical care straight away. Refer to the Safety Data Sheet (SDS) for full details.
$11.07
Craftright Hot Melt Glue Sticks are a clear, 20 pack of mini glue gun refills aimed at craft, hobby and light household projects. They suit any hot glue gun that takes a 7.2mm stick, so they are a handy way to keep a compact glue gun stocked for a long run of jobs.About the formulaThese are clear hot melt adhesive sticks. The stick melts inside the glue gun, comes out as a hot, tacky bead, then cools and sets quickly as it returns to room temperature. Craftright describes them as quicker setting than many other glue types, and as giving a secure bond on many different materials.Where to use itIndoors: craft and hobby projects, model making, decorating, small repairs and general fixing around the house.Outdoors: no outdoor or weather-resistance claims are confirmed for this product, so test a sample first if you plan to use it outside.Suitable for joining a range of common craft and household materials. Because the maker does not list specific surfaces, always test on a small hidden area first, particularly on foam, thin plastics and other heat-sensitive materials.How to use itMake sure the surfaces are clean, dry and free of dust, oil and grease. Load one stick into a hot glue gun that accepts 7.2mm sticks and let the gun heat fully, following the gun maker's instructions. Apply a bead to one surface, press the parts together promptly and hold them still until the glue has set and cooled.Important notesUse only in guns designed for 7.2mm sticks. Do not force a stick into a gun with a wider barrel. Work quickly, because hot melt adhesive starts to set soon after it leaves the nozzle. Open time, bond strength and temperature resistance are not confirmed by the manufacturer for this product, so do not rely on it for structural, load-bearing or high-heat situations.Specifications Brand Craftright Product Hot Melt Glue Sticks Pack 20 sticks Stick size 7.2mm x 100mm Colour Clear Base Hot melt adhesive Application Hot glue gun with 7.2mm stick capacity Use Craft and hobby SafetyMolten glue and the gun nozzle get hot enough to cause burns, so keep them away from skin, children and pets. Do not touch freshly applied glue. Use the gun on a stable, heat-safe surface and unplug it when you finish. If you get hot glue on your skin, cool the area under running water straight away and do not peel the glue off. Refer to the Safety Data Sheet (SDS) for full details.
$5.81
The Gyprock Rapid Repair Kit is a complete, ready-to-go pack for patching damaged plasterboard walls and ceilings, from small nicks and cracks through to holes up to 150mm x 150mm. Everything needed for the job is supplied in one mixing bucket, so a first-time DIYer can go from damaged wall to a surface ready for paint without hunting down separate products or tools.About the formulaThe compound in the kit is Gyprock Rapid Patch, a fast-setting dry powder that you mix with clean water into a smooth paste. Gyprock lists a working life of around 20 minutes once mixed, with minimal shrinkage when filling small cracks and dents, and a surface that is ready to sand in around 40 minutes. Gyprock lists the powder at a specific gravity of 2.3 to 2.4 and a low VOC content, under 10 g/L per material. The kit is made in Australia by CSR Gyprock.What is in the kit 1kg bag of Gyprock Rapid Patch compound 2 x Gyprock plasterboard repair panels (150mm x 150mm) for larger holes Gyprock Easy Tape (20 metres) 100mm broadknife Sanding block Mixing bucket (also the kit's packaging) Step-by-step instructions Where to use itIndoors: patching dents, scratches, cracks and holes in plasterboard walls and ceilings, including door-handle dings and holes left by removed fixings or fittings.Other substrates: the Rapid Patch compound itself is also rated by Gyprock for repairs to fibre cement, timber and masonry, and it can be used as an all-purpose compound for setting plasterboard joints. Check the substrate and the finish before using it in damp areas.Suitable materials include plasterboard (the main use of the kit), fibre cement, timber and masonry (the compound only).How to use itRemove any loose paint or crumbling material around the damage and lightly sand the edges. Mix the powder with clean water to a creamy consistency. Gyprock's guide for small repairs is about 1 cup (260g) of powder to 150mL of water. Only mix as much as you can use in around 20 minutes. For small nicks and cracks, fill with the broadknife, let it set, then sand smooth. For larger holes, cut and fit a repair panel with backing blocks fixed using the compound, cover the joins with Easy Tape, and apply compound over the tape. Let each coat set fully before the next, then sand lightly and the wall is ready to paint.Important notesUse clean domestic water for mixing, and wash tools before the compound sets. The kit is aimed at repairs up to 150mm x 150mm, so larger damage will need a bigger repair. You may also need a hand saw, trimming knife, pencil, dust mask and eye protection depending on the job. Store unused compound dry, out of the weather and out of direct sunlight.Specifications Brand Gyprock (CSR) Product Rapid Repair Kit Pack Single kit, 1.5kg nominal (1kg Rapid Patch compound plus panels, tape and tools) Base Plaster-based dry powder, mixed with water Application Hand applied with the supplied broadknife Working time (Rapid Patch) About 20 minutes Ready to sand (Rapid Patch) About 40 minutes Repair size Up to 150mm x 150mm Specific gravity 2.3 to 2.4 VOC content Under 10 g/L per material Suitable surface Plasterboard walls and ceilings Origin Made in Australia SafetyCutting, sanding or grinding the set material makes dust that can irritate the eyes, nose and throat, so wear a dust mask and eye protection and avoid prolonged skin contact. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$49.75
Soudal Genius Gun Gap Filling Expanding Foam is a one-handed, ready-to-use polyurethane foam for filling gaps, holes and joints while adding thermal and acoustic insulation, supplied here as a single 500ml can. The applicator trigger is built into the can, so there is no need to buy a separate foam gun, and the can can be put away part-used and picked up again on the next job.About the formulaA one-component, moisture-curing polyurethane foam with a stable, thixotropic body that stays where you put it. A built-in trigger and straw let you control the amount you dispense, and the resealable applicator keeps the can usable for up to 6 weeks after first use. Once cured it is light, sound-reducing and chemically inert, with minimal shrinkage and very little post-expansion. Manufacturer data lists a free-foamed density of about 25 kg/m³, sound insulation of 58 dB and thermal conductivity of 0.037 W/m.K. One 500ml can yields roughly 19 litres of free foam, or about 17 metres of joint fill. The foam is champagne in colour and is not UV resistant, so exposed foam needs a protective finish.Where to use itIndoors: filling gaps around door and window frames, sealing pipe and cable penetrations, closing holes and cavities in walls and ceilings, cutting down draughts and thermal bridges, and adding a sound-deadening layer.Outdoors: sealing gaps and openings in roof constructions and around frames and penetrations. Cover the cured foam with paint, plaster or sealant to protect it from UV light.Suitable materials include brick, concrete, masonry, timber, metals and most plastics, as well as most other common building materials. It does not bond to polyethylene (PE), polypropylene (PP) or PTFE. Run a quick adhesion test on unusual substrates first.How to use it Make sure surfaces are clean, dry and free of dust and grease, then lightly mist them with water to help the foam cure. Shake the can hard for at least 20 seconds, then open the cover and fold the tube out horizontally. Turn the can over and squeeze the trigger to dispense. Fill holes and cavities only about one third full, as the foam expands a lot as it cures. Shake the can again every so often while you work. For deep voids, build up in layers and moisten between each layer. When you finish, detach the bung, plug the nozzle with it, close the cap and store the can upright. Once fully cured, trim the foam with a sharp knife, then sand, paint, plaster or cover with sealant as needed. Important notesWipe off uncured foam straight away with Soudal Gun and Foam Cleaner or acetone, and test the cleaner on plastics, lacquer and paint first as they can be affected. Cured foam can only be removed mechanically or with a PU foam remover, and it must never be burned off. Use the product between roughly +5°C and +30°C. Skin forms in about 7 minutes and the foam can be cut after about 25 minutes (manufacturer figures, measured under standard test conditions, so real-world times vary with temperature, humidity and bead size). Cured foam is not UV resistant. Do not use it near electrical boxes or light fittings without checking the clearance guidance. Unopened cans keep for at least 12 months when stored upright in a cool, dry place at +5°C to +25°C.Specifications Brand Soudal Product Genius Gun Gap Filling Expanding Foam Manufacturer code 132272 Pack 1 x 500ml aerosol can Colour Champagne Base One-component polyurethane, moisture curing Application Built-in Genius Gun trigger applicator, one-handed Reusable Up to 6 weeks after first use Skin formation About 7 minutes Cutting time About 25 minutes Yield (500ml) About 19 L of free foam, about 17 m of joint fill Shrinkage after curing Under 3% Expansion after curing Under 1% Temperature resistance (cured) -40°C to +90°C, up to 120°C for a maximum of 1 hour Can size 65 x 65 x 315mm Use Interior and exterior (protect from UV) SafetyThis is a pressurised aerosol with flammable propellant and contains isocyanates. Keep it away from heat, sparks, flames and other ignition sources, do not smoke while using it, and never pierce or burn the can, even when empty. Wear gloves, safety glasses and protective clothing, and use only in well-ventilated areas. People already sensitised to isocyanates, or with asthma, eczema or skin problems, should avoid contact with the product. Refer to the Safety Data Sheet (SDS) for full details.
$16.20
Turbo Concrete Bog is a fast-setting polyester repair filler for patching holes, chips and cracks in concrete, brick and masonry, supplied here in a 500ml container. It is often described as concrete in a can. It sets hard in minutes and dries to a dull grey that looks like real concrete, so small repairs can be finished on the same day.About the formulaThis is a two part system. The filler is a paste based on unsaturated polyester resin in styrene, and it is cured with a benzoyl peroxide hardener that is mixed in at the time of use. The paste has a no-slump body, so it stays put on vertical and overhead repairs without sagging. Turbo describes the cured repair as strong and water resistant, with no shrinkage. The cured filler can be painted with water based or oil based paints or epoxy floor coatings, usually within about an hour. It can also be left unpainted, or tinted with dry oxides to match coloured concrete.Where to use itIndoors: filling old dynabolt holes and repairing chips or cracks in garage and shed floors, steps and masonry walls.Outdoors: repairing driveways, paths, steps, brick and masonry walls.Suitable materials include concrete, brick and other masonry surfaces.How to use itClean the damaged area and about 5cm around it. The surface must be dry and free of dirt, dust, oil, wax, grease, paint and anything else that could stop the filler bonding. Mix the filler and hardener carefully in the proportions given on the pack. Weather and temperature affect how fast the mix cures, so work in manageable batches. Press the mixed filler firmly into the hole or crack and shape it before it hardens. Once cured it can be sanded, then painted or left as is.Important notesThe hardener is a separate component. Check what is in the pack when you receive it, because Turbo also sells its Red Hardener separately. Use the hardener amount recommended on the label, since changing it changes the set time. This is a repair filler, not an adhesive and not a concrete additive. It is not stainable. Always follow the mixing and application directions on the pack.Specifications Brand Turbo Product Concrete Bog Size 500ml Colour Light grey paste, dries to a dull grey Base Unsaturated polyester resin in styrene (two part, with benzoyl peroxide hardener) Application Hand applied with a putty knife or similar tool Dry to touch About 30 minutes Paintable Within about 1 hour Sandable Yes Stainable No Use Interior and exterior SafetyKeep it away from heat, sparks and flames. Work in a well-ventilated area and wear suitable gloves and eye protection. Store in a closed container in a dry, cool place below 30°C. Refer to the Safety Data Sheet (SDS) for full details.
$31.19
Icon Plastics PVC Solvent Welding Cement is a fast-setting white solvent cement made for joining PVC fittings and pipe, supplied here in a 180g size. It is designed to go with the Icon Plastics surface drainage and rainwater range, and the manufacturer also positions it for irrigation, plumbing, pool and spa work.About the formulaA solvent-based PVC cement. It works by softening the surfaces of the PVC so the two parts fuse into one joint as the solvent leaves, rather than sticking them together with a separate glue layer. The listed solvents are methyl ethyl ketone and tetrahydrofuran. It is approved to AS/NZS 4020 for use with potable water.Where to use itIndoors: PVC plumbing fittings and pipework, and PVC pool and spa plumbing connections.Outdoors: PVC irrigation lines, and Icon Plastics surface drainage and rainwater fittings.Suitable for PVC pipe and fittings. It is not intended as a general-purpose glue for other plastics, timber or metal.How to use itCut the pipe square and remove burrs. Make sure the pipe end and the fitting socket are clean, dry and free of dirt, oil and grease. Apply an even coat of cement to both surfaces, push the pipe fully into the fitting and hold it briefly so it does not push back out. Wipe away any excess. Close the container tightly straight after use so the solvent does not evaporate. Follow the directions on the pack for set and cure times before the joint is pressurised or put into service.Important notesMake sure the joint has fully set and cured before it is tested or put under water pressure. Work in a well-ventilated area and keep the product away from heat, sparks and flames. Check the pack for any limits on pipe sizes and pressure ratings. Pipe and fitting suitability should be confirmed against the relevant plumbing standard for your job.Specifications Brand Icon Plastics Product PVC Solvent Welding Cement Size 180g Colour White Base Solvent-based (methyl ethyl ketone, tetrahydrofuran) Set speed Fast setting Standard Approved to AS/NZS 4020 for potable water Use PVC plumbing, irrigation, pool and spa, Icon Plastics surface drainage SafetyThis product contains strong, volatile solvents. Treat it as flammable: keep it away from ignition sources, do not smoke while using it, and store it in a cool, well-ventilated place with the lid tightly closed. Avoid breathing the vapours and avoid skin and eye contact. Wear chemical-resistant gloves and eye protection, and keep it out of reach of children. Always read the manufacturer Safety Data Sheet and the pack label before use.
$20.79
![Roberts Quick-Repair Floor Putty 88ml [Tan] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-tan-2.png?v=1792410981&width=645)
Roberts Quick-Repair Floor Putty in Tan is a ready-to-use acrylic putty for hiding gaps, nicks, scratches and fixing holes in laminate, hybrid, vinyl and engineered timber floors, supplied in an 88ml squeeze tube. It works as a quick touch-up fix for existing floors and as a finishing step during installation, and the colour can be used straight from the tube or blended with other Roberts putty shades to match your floor.About the formulaAn acrylic-based putty that is ready to use with no mixing. It dries quickly without shrinking, so the repair stays level with the surrounding surface. Once dry it can be sanded smooth or painted over. It is a low VOC formula and has a two-year shelf life.Where to use itIndoors: filling nail and screw holes during floor installation, and repairing chips, nicks, scratches and small gaps on floors that are already laid, including around joins and transitions.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, hybrid and vinyl flooring (plank and tile) and engineered timber flooring.How to use it Make sure the area is clean and free of dust and debris. Choose the Tan shade on its own, or mix it with other Roberts putty colours to get the closest match to your floor. Knead the tube well for at least 20 seconds before use. Cut the tip to suit the size of bead you need and press the putty into the damaged area. Spread it into the gap, nick or scratch with a putty knife so it fills evenly. Wipe away excess straight away with a damp rag and do not let it dry on the surrounding floor. Allow about 30 minutes to dry. The dried repair can be lightly sanded or painted if needed. Important notesColour match depends on your floor, so test a small hidden spot first and blend shades if needed. Store at room temperature and do not let the tube freeze, as freezing can affect performance. This is not a structural or waterproof repair product. For large areas of damaged flooring, replace the affected boards or planks.Specifications Brand Roberts Product Quick-Repair Floor Putty (model PC7730) Size 88ml squeeze tube Colour Tan Base Acrylic Application Squeeze tube, spread with a putty knife Dry time About 30 minutes Finish Matte Shelf life 2 years Use Interior floors SafetyAvoid contact with eyes and skin. If it gets on skin, wash with soap and plenty of water. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Dark Brown] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-dark-brown-2.png?v=1792410954&width=645)
Roberts Quick-Repair Floor Putty in Dark Brown is a ready-to-use acrylic filler for hiding gaps, nicks and scratches in modern click-together and plank flooring, supplied in a handy 88ml squeeze tube. It suits quick touch-ups on existing floors as well as tidying up nail and screw holes during installation, and the dark brown shade can be used on its own or blended with other Roberts colours to get closer to your floor.About the formulaAn acrylic-based putty that is formulated to dry quickly without shrinking. Once dry it can be sanded or painted, so you can refine the repair after it sets. It is a low VOC formula, and it is supplied in a soft tube so you can apply it straight from the pack with no mixing. Roberts quotes a two-year shelf life.Where to use itIndoors: filling small scratches, chips, dents and open joints on laminate, hybrid, vinyl and engineered timber floors; concealing nail and screw holes while a floor is being installed; touching up localised damage on floors that are already in place.Outdoors: not intended for exterior use.Suitable surfaces include laminate, hybrid flooring, vinyl flooring and engineered timber flooring. Choose, or mix, a shade that matches the lightest base colour of the floor for the most natural result.How to use itMake sure the area is clean, dry and free of dust and loose debris. Knead the tube thoroughly for at least 20 seconds before use. Squeeze the putty into the gap, nick or hole and work it in with a putty knife or similar tool so it sits flush with the surface. Wipe excess off the surrounding floor with a damp rag before it dries, because dried residue on the floor surface is harder to remove. When the putty has dried it can be lightly sanded or painted if needed. Test the colour on an offcut or an inconspicuous spot first.Important notesThis is a cosmetic filler for small damage, not a structural repair product. Deep chips or large missing areas may need a different repair method. The putty is not rated as water resistant, so it is not recommended for wet areas or continual moisture. Store at room temperature and do not let the tube freeze, as freezing may affect performance. Reseal the tube after use. Colour on screen may vary slightly from the real product, so check the shade before committing to a full repair.Specifications Brand Roberts Product Quick-Repair Floor Putty Size 88ml tube Colour Dark Brown Base Acrylic Application Squeeze tube, applied by hand Finish options Can be sanded or painted once dry Suitable floors Laminate, hybrid, vinyl and engineered timber Shelf life 2 years VOC Low VOC Use Interior floors SafetyIt is marketed as low VOC and safe to use, but normal care still applies: avoid contact with eyes, keep out of reach of children, and wash hands after use. Do not swallow. Store the tube at room temperature and protect it from freezing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Greige] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-greige-2.png?v=1792410943&width=645)
Roberts Quick-Repair Floor Putty in Greige is a ready-to-use acrylic filler for patching gaps, nicks and scratches in laminate, hybrid, vinyl and engineered timber floors, supplied in a handy 88ml squeeze tube. It suits both flooring installers and home owners, and the neutral grey-beige shade can be used on its own or mixed with other Roberts putty colours to blend into your floor.About the formulaAn acrylic-based putty that is ready to use straight from the tube, with no mixing and no tools needed beyond a putty knife. It dries quickly, is formulated not to shrink, and can be sanded or painted once dry. It is low in VOCs, and the tube has a shelf life of two years.Where to use itIndoors: filling nail and screw holes left after laying a floor, closing small gaps at plank edges, and hiding chips, nicks and scratches on floors that are already installed.Outdoors: not intended for outdoor use.Suitable surfaces include laminate, hybrid flooring, vinyl (plank and tile) and engineered timber flooring.How to use itMake sure the area is clean and free of grease, dirt and loose debris. Choose the shade closest to your floor, ideally matching the lightest base colour of the surface, or blend two colours together to get a closer match. Knead the tube thoroughly for at least 20 seconds, cut the tip to suit the size of the repair, then press the putty into the damaged area with a putty knife until it is filled. Wipe away excess with a damp rag straight away and do not let it dry on the surrounding floor. Once dry, the repair can be lightly sanded or painted if needed.Important notesColour is best checked on a small hidden spot first, as the shade can look different once dry and on different floors. Store the tube at room temperature and do not let it freeze, as freezing may affect performance. Reseal the tube after use. This putty is made for floor repairs and is not designed to be a structural adhesive or a wet area sealant.Specifications Brand Roberts Product Quick-Repair Floor Putty Size 88ml squeeze tube (single) Colour Greige (grey-beige) Base Acrylic Application Squeeze tube, applied by hand with a putty knife Finish Can be sanded or painted when dry VOC Low VOC Shelf life 2 years Use Indoor floor repair: laminate, hybrid, vinyl and engineered timber SafetySwallowing large amounts may upset the stomach. Wear protective gloves and eye protection when using it. If breathed in, move to fresh air. If it gets on skin, wash off with soap and plenty of water and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
Ramset UltraFix Plus is a fast-setting, styrene-free polyester anchoring adhesive for fixing threaded studs and reinforcing bar into solid concrete and hollow masonry, supplied here as a single 300ml cartridge with two mixer nozzles. It is a medium duty chemical anchor that fits a standard caulking gun, so it suits small to mid-sized fixing jobs on site or around the home without specialist dispensing gear.About the formulaA two-part marine grade polyester resin. Part A is a polyester and filler paste and Part B is a peroxide catalyst, and the two are blended as the product passes through the mixer nozzle. The cartridge is styrene free for lower odour and is VOC compliant. The body is non-drip and resists slumping, which helps with horizontal and overhead holes. It is also designed to dispense easily in cool weather. The resin has been assessed for use in flooded holes under European Technical Assessment ETA 13/0681 (ETAG 001 Part 5, Option 7, in solid concrete).Where to use itIndoors: fixing brackets, hinges, plumbing and electrical fixtures and similar steel or timber fittings to solid concrete or hollow brick and block.Outdoors: setting gates, fence posts and fittings, signposts, guard rails and hand rails into concrete or masonry, including damp or wet holes.Suitable base materials include solid concrete, natural stone, hollow brick and hollow concrete block. It is intended for anchoring steel threaded rod, studs and reinforcing bar, and for fixing steel and timber fittings to those substrates. Hollow substrates are normally anchored with perforated sleeves (sold separately), so check Ramset installation data for your application.How to use itDrill the hole to the diameter and depth specified in Ramset installation data for your fixing, then clean it thoroughly with a brush and blow out the dust. Fit a mixer nozzle to the cartridge, load it into a standard caulking gun and dispense a little to waste until the mixed material is an even grey. Fill the hole from the bottom to avoid trapping air, then push the stud or bar in with a slight twist and leave it undisturbed. At 20°C the working time is about 6 minutes and the fixing can be loaded after about 50 minutes. Cure takes longer in cooler conditions. Always wear gloves and eye protection while mixing and installing.Important notesUse the supplied mixer nozzles only, as the adhesive relies on them to blend correctly. Do not use it in poorly ventilated or confined spaces. Cure and loading times depend on temperature, so allow longer when it is cold. For structural or load-critical fixings, follow Ramset technical data and engineering guidance for embedment, spacing and loading. Heavy duty or high-load applications may call for a higher-rated Ramset chemical anchor.Specifications Brand Ramset Product UltraFix Plus Chemical Anchoring Adhesive (model UFP300) Pack 1 x 300ml cartridge with 2 x mixer nozzles Colour Grey when mixed (Part A white, Part B black) Base Marine grade polyester, styrene free Application Cartridge, via standard caulking gun with mixer nozzle Working time About 6 minutes at 20°C Loading time About 50 minutes at 20°C Heat distortion temperature 80°C Approvals ETA 13/0681 (ETAG 001-5 Option 7, solid concrete, including flooded holes) Substrates Solid concrete, stone, hollow brick, hollow concrete block SafetyIt is not classified as a physical hazard and is non-flammable. Wear protective gloves, protective clothing and eye protection, avoid breathing vapours, wash thoroughly after handling and keep it out of drains and waterways. In case of eye contact, hold the eyes open and rinse with water for at least 15 minutes and seek medical help. For skin contact, remove contaminated clothing and wash the skin well, and seek advice if irritation or a rash develops. Refer to the Safety Data Sheet (SDS) for full details.
$41.97
Ramset ChemSet 101 Plus is a two-part, marine grade polyester anchoring adhesive for fixing threaded studs and starter bars into solid and hollow base materials, supplied here as a single 600ml cartridge with two mixing nozzles. It is made for trade and site work. Typical jobs include steel columns, machinery hold-downs, handrails and post-installed reinforcing bar.About the formulaThe resin is a marine grade polyester. Part A is a polyester polymer with inorganic filler, and Part B is a benzoyl peroxide catalyst. The two parts mix into a grey paste as they pass through the nozzle. The formula is styrene free, so it has a lower odour and low VOC once cured. It is non-drip and slump resistant, which suits overhead and vertical holes. It dispenses easily in cold weather. The resin is designed to reach full load capacity in dry, wet and flooded holes, as assessed to EAD 330499 Option 7. The cured adhesive is vibration resistant.Where to use itIndoors: machinery and equipment hold-downs, plate and frame fixings, handrails and balustrades, and starter bars or post-installed reinforcing bar.Outdoors: structural steel columns and beams, facade pins, gates, fencing posts and safety barriers, including in wet or flooded holes.Suitable base materials include solid concrete, brick and hollow concrete block, and it bonds steel threaded studs and reinforcing bar into them. Always check the Ramset load tables and the Specifiers Anchoring Resource Book for the design capacity of your application.How to use itFit the supplied mixing nozzle and load the cartridge into a compatible applicator, such as the Ramset ChemSet universal applicator. Dispense and discard the first portion until the colour is an even grey. Drill, clean and prepare the hole as set out in the Ramset installation instructions for your anchor type and size. Inject from the bottom of the hole, insert the stud or bar with a slight twist, and leave it undisturbed. Do not load the anchor until the cure time has passed. Fit a fresh nozzle if you stop work for longer than the working time.Important notesWorking time is about 6 minutes and loading time is about 50 minutes at 20°C. Cure times change with temperature, so check the Ramset data sheet for colder or warmer conditions. Installation is recommended with the base material and adhesive between 5°C and 40°C. The cartridge should not be below 5°C. The resin is not resistant to solvents such as acetone, benzene, xylene and styrene. Anchor design, hole preparation and loading should follow the manufacturer's technical documents, and critical structural fixings should be specified by a qualified engineer.Specifications Brand Ramset Product ChemSet 101 PLUS Polyester Anchoring Adhesive Model code C101S Pack 1 x 600ml cartridge with 2 x mixing nozzles Colour Part A white, Part B black, mixed grey Base Two-part polyester (styrene free) Application Cartridge, via a compatible applicator and mixing nozzle Working time About 6 minutes at 20°C Loading time About 50 minutes at 20°C Density 1.69 kg per litre at 20°C Heat distortion temperature 80°C (ISO 75) Service temperature -40°C to 80°C Installation temperature 5°C to 40°C (substrate and adhesive) Hardness Shore D 90 (ISO 7619) Compressive strength 70 MPa (ASTM 695) Tensile strength 12.2 MPa (ASTM D638) Flexural strength 28.3 MPa (ASTM D638) Assessment EAD 330499 Option 7 (flooded holes) Use Interior and exterior SafetyKeep it away from heat, sparks and open flames, and keep the container closed. Use it in a well-ventilated area and avoid breathing vapours. Wear protective gloves, protective clothing and eye or face protection. Wash thoroughly after handling and do not release it to the environment. Refer to the Safety Data Sheet (SDS) for full details.
$66.31
Boyle Clear Spray Adhesive is a handy aerosol glue for bonding and mounting lightweight materials around the home, office and craft table, supplied here as a single 350g can. It goes on as an even spray and dries clear, so it suits neat jobs where you don't want visible glue lines.About the formulaA solvent-based spray adhesive. The supplied product data lists a light aliphatic petroleum solvent, dichloromethane and a hydrocarbon propellant. The nozzle spray gives broad, even coverage, and the adhesive is quick drying. Once cured it is clear, moisture resistant, UV/sunlight resistant and drillable. It is not solvent resistant and cannot be sanded.Where to use itIndoors: mounting prints, photos and artwork, laminating paper and card, and general craft, scrapbooking and office projects.Around the workshop: light bonding and mounting jobs on timber, metal, glass and fabric where a clear, even bond is wanted.Suitable materials include cardboard, cork, wood, paper, fabric, glass, prints and photographs, and metal. Plastics and foams are not listed by the manufacturer, so test a small hidden area first.How to use itShake the can well before use. Hold it roughly 20 to 25cm from the surface and spray an even coat. For a temporary bond, spray one surface only, let it dry, then press the surfaces together. For a permanent bond, spray both surfaces, wait until they turn tacky, then press them together firmly. Always test on an offcut or sample before coating the full surface. Work in a well-ventilated area and keep the nozzle clear of ignition sources.Important notesThis adhesive is designed for lightweight materials, not heavy or structural loads. It is not solvent resistant and not sandable. Solvent-based sprays can mark or soften some foams and plastics, so a test patch is a must. Full cure times are not published by the manufacturer, so allow plenty of time before putting the bond under stress.Specifications Brand Boyle Product Clear Spray Adhesive Size 350g aerosol can (single) Colour Clear Base Solvent-based (petroleum solvent, dichloromethane, hydrocarbon propellant) Application Aerosol nozzle spray Recommended use Bonding and mounting Dries clear Yes Moisture resistant Yes UV/sunlight resistant Yes Drillable Yes Solvent resistant No Sandable No SafetyUse only outdoors or in a well-ventilated area, and do not breathe the spray or mist. Wear protective gloves and eye protection, and wash hands and exposed skin after handling. Keep away from heat, sparks, open flames and hot surfaces, and don't spray near an ignition source. Do not pierce or burn the can, even when empty. Refer to the Safety Data Sheet (SDS) for full details.
$22.22
Selleys Plastic Wood is a fast-setting, solvent-based wood filling cement for repairing holes, dents and chips in interior timber, supplied here in a 230g maple-coloured tin. It is a simple fix for furniture, skirting, architraves and other indoor joinery, and once set it can be worked much like the timber around it.About the formulaA solvent-based paste containing natural wood fibres, finished in a maple (tan) colour. It dries quickly to a hard finish that holds up to sanding, nailing and planing. Once dry it can be stained, varnished, painted or lacquered, so the repair can be finished in the same way as the surrounding wood. It is a rigid filler, so it is not designed for joints that move.Where to use itIndoors: filling nail holes, dents, chips and small cracks in furniture, doors, window frames, skirting boards, architraves and other interior woodwork.Outdoors: not recommended. The manufacturer rates this product for interior use only.Suitable materials include natural timber and wood veneer.How to use itStir the product thoroughly before use. Make sure the surface is clean, dry and free of loose material. Press the filler in with a putty knife and slightly overfill deeper holes so there is room to sand back flush. Do not fill deeper than 6mm in a single application. Let it dry fully before sanding, staining, painting or lacquering. Wipe the putty knife clean with methylated spirits. Press the lid on firmly after use and store the tin somewhere cool.Important notesNot suitable for exterior use. Not recommended where structural movement may occur, so use a flexible product for joints and gaps between surfaces. Work in a well-ventilated area. Colour is maple only, so test a small area first if you need to match a different timber tone, or plan to stain or paint over the repair.Specifications Brand Selleys Product Plastic Wood Filler Cement Size 230g tin Colour Maple Base Solvent-based, with natural wood fibres Application Putty knife Maximum fill depth 6mm per application Set speed Fast setting Clean up Methylated spirits Use Interior only SafetyThis is a highly flammable solvent-based product. Keep it away from heat, sparks, flames and other ignition sources, and avoid static discharge. It can irritate skin and eyes, and the vapours may cause drowsiness or dizziness. Use only in a well-ventilated area and avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.
$38.42
Elmer's Glue-All Multi-Purpose Extra Strong Liquid Glue is a general-purpose white PVA glue for craft tables, classrooms and light household repairs, supplied in a 473ml bottle. It joins porous and semi-porous materials such as paper, fabric, wood, leather and ceramics, and its easy, ready-to-use formula suits beginners and families.About the formulaA water-based, white PVA (polyvinyl acetate) liquid glue with a mild vinegar-like odour. The manufacturer describes it as non-toxic, with a strong bond and a quick-drying, clear-drying finish. It needs no mixing, and it can also be used to make homemade glue slime.Where to use itIndoors: school and craft projects, paper and cardboard work, fabric and leather crafts, small timber and ceramic repairs, and odd jobs around the kitchen, workshop, den or garage.Outdoors: not recommended. The product is intended for indoor use only.Suitable materials include paper, cardboard, fabric, wood, leather and ceramics.How to use itMake sure the surfaces are clean, dry and free of dust, oil and grease. Apply a thin, even layer of glue to one or both surfaces, press the parts together and hold or clamp them until the glue grips. Wipe away any excess straight away with a damp cloth, as wet glue washes up with soap and water. Leave the bond to fully dry before putting it under load. Close the cap firmly after use.Important notesDo not use on photos, bare metal, or surfaces that will be submerged or heated. Keep the product from freezing, because freezing can damage the glue. This is not a structural adhesive, so choose a purpose-made product for load-bearing or outdoor jobs. Always test a small hidden area first on delicate or finished surfaces.Specifications Brand Elmer's Product Glue-All Multi-Purpose Extra Strong Liquid Glue Size 473ml bottle Colour White liquid Base PVA (polyvinyl acetate), water-based Application Bottle, applied by hand Clean up Soap and water while wet Use Indoor use SafetyNormal use does not call for special protective equipment, but wash your hands after use and keep the bottle out of reach of young children. In case of eye contact, rinse well with water. Store in the original container with the cap closed, away from freezing conditions. Refer to the Safety Data Sheet (SDS) for full details.
$12.07
Gorilla Super Glue 20g is a fast-setting, clear-drying instant adhesive for quick household repairs, supplied here as a single 20g bottle. It is a rubber-reinforced cyanoacrylate that grips within seconds and is designed to cope with everyday knocks and drops better than a standard instant glue.About the formulaA liquid ethyl cyanoacrylate adhesive that cures when it meets the trace moisture on the surfaces being joined, so no clamping or mixing is needed. Gorilla markets the rubber-toughened formula as Impact-Tough, meaning the cured bond is better able to absorb bumps and wear. The bottle has an anti-clog cap with a metal pin inside that seals out air, which helps stop the glue drying out in the nozzle and lets you come back to the same bottle for repeat jobs. Once cured, the glue dries clear for a neat finish.Where to use itIndoors: small household repairs such as ceramics and crockery that will not be used for food, trinkets, toys, craft pieces, leather goods, paper items and loose trim or fittings.Outdoors: the manufacturer recommends Gorilla Super Glue primarily for indoor use, so choose a more weather-resistant adhesive for outdoor repairs that face constant moisture or sun.Suitable materials include metal, wood, ceramic, stone, rubber, leather, paper and most plastics. It is not recommended for polyethylene, polypropylene or similar plastics, and it is best to test an inconspicuous spot on any plastic first.How to use itProtect your work area from spills, and make sure the surfaces are clean and dry. Open the cap and apply a small amount to one surface, as a thin layer gives the best result. Press the parts together and hold them still until the glue grips, which takes seconds, so no clamp is needed. Wipe the nozzle clean and refit the cap firmly after each use so the metal pin can seal the bottle.Important notesCyanoacrylates need a little surface moisture to cure, so extremely dry surfaces can bond more slowly. Excess glue can bond skin in moments, so work carefully and keep fingers clear of the joint. Do not use as a load-bearing safety device. Not recommended for polyethylene or polypropylene plastics. Once cured, the manufacturer states the bond can hold from about -53°C to 104°C. Gorilla suggests unopened shelf life of roughly 18 to 24 months from manufacture, and up to about 6 months once opened is a good guide.Specifications Brand Gorilla Glue Product Gorilla Super Glue Pack 20g bottle (single) Colour Clear when dry Base Ethyl cyanoacrylate, rubber-toughened Application Squeeze bottle with anti-clog metal pin cap Set time About 10 to 45 seconds, no clamping required Cured temperature range -53°C to 104°C Use Primarily indoor SafetyUse only outdoors or in a well-ventilated area, avoid breathing vapours, and wear protective gloves and eye protection. Keep away from heat, sparks and open flames, keep the container tightly closed and keep out of reach of children. Wash hands thoroughly after handling. If skin is bonded, do not pull apart; soak in warm soapy water and ease the skin gently apart. Refer to the Safety Data Sheet (SDS) for full details.
$17.47
Gorilla Super Glue Gel is a thick, no-run cyanoacrylate adhesive for quick household repairs, supplied here as a 20g bottle. The gel body gives you much more control than a thin liquid super glue, so it suits vertical surfaces, uneven parts and small jobs where you do not want drips. It sets fast with no clamping and dries clear.About the formulaAn ethyl cyanoacrylate gel that sets in about 10 to 45 seconds depending on the amount of glue and the surface. It is formulated to cope with knocks, drops and shocks, so repaired items stand up to everyday handling better than with a brittle super glue. The bottle has an anti-clog cap with a metal pin that helps keep air out, so the glue stays usable between jobs. The gel can separate over time, so shake the capped bottle before use.Where to use itIndoors: household and craft repairs on ceramics, trims, handles, toys, shoes and leather goods, small furniture fixes, and other jobs where a quick, clear bond is wanted.Outdoors: the manufacturer recommends Gorilla Super Glue primarily for indoor use, so treat this product as an indoor repair glue.Suitable materials include most plastics, metal, wood, ceramic, stone, rubber, leather, paper and fabric. Not recommended for polyethylene, polypropylene or similar low-energy plastics. Test a small hidden area first on delicate or finished surfaces.How to use itProtect your work area from spills. Make sure the surfaces are clean and dry. With the cap on, shake the bottle, then turn it upside down and tap it on a hard surface to move the gel into the nozzle. Remove the cap and apply a small amount to one surface only. Use about one drop per 6.5 cm2, because too much glue can delay the bond or cause it to fail. Press the parts together for about 10 to 45 seconds. Gaps and uneven surfaces can slow the bond. Allow 24 hours for a full cure. After use, wipe the nozzle with a dry cloth, refit the cap and keep the bottle in a cool, dry place away from moisture.Important notesNot for use on polyethylene or polypropylene plastics. Cyanoacrylate bonds skin in seconds, so never pull bonded skin apart. Soak the area in warm soapy water and gently work it free, or use acetone according to the solvent maker's directions. Acetone can mar surfaces and discolour fabric. The glue reacts with water and alkaline materials, generating heat, so keep it away from moisture. It is not intended for food contact and should not be stored in the fridge.Specifications Brand Gorilla Glue Product Super Glue Gel Size 20g bottle Colour Clear Chemistry Ethyl cyanoacrylate gel Application Squeeze bottle with anti-clog cap, hand applied Set time About 10 to 45 seconds Full cure 24 hours Service temperature (cured) About -53°C to 104°C Use Primarily indoor SafetyHazard classification: combustible liquid, causes skin irritation, causes serious eye irritation, may cause respiratory irritation. Bonds skin and eyes in seconds. Keep out of reach of children. Use in a well-ventilated area, avoid breathing vapours, and keep away from heat, sparks and open flames. Refer to the Safety Data Sheet (SDS) for full details.
$17.47
Turbo Builder's Bog is a trade quality, two part polyester filler for repairing damaged and rotted timber, supplied here in a 500ml can for builders, painters and capable DIYers. It sets to a hard, wood-like finish that you can sand, drill and paint, so it suits window sills, door frames and other jobs where replacing the timber is not practical.About the formulaA polyester-based filler paste that cures by a chemical reaction when mixed with the red hardener paste, rather than by drying out. Because of this, it shows no obvious shrinkage. You choose the working time by adjusting how much hardener you add within the range printed on the can, and the mix also sets faster in warm weather. As it sets it passes through a soft, cheese-like stage where it can be trimmed with a blade or a surform file. Shaping at this point saves a lot of sanding. It spreads smoothly, holds its shape on large fills without slumping, and bonds firmly to timber.Where to use itIndoors: filling holes, gaps and dents in architraves, skirtings, door frames and other timber trims before painting.Outdoors: repairing window sills, sashes, fascias, decks and door frames, including areas where the timber is partly rotten, once the soft material has been cleared back to sound wood.Suitable material is timber. It is designed as a timber repair filler and can be painted over once cured. Test first before using on other surfaces.How to use itMake sure the timber is clean, dry, unpainted, roughened and free of rot. Remove any soft or crumbling material first. Place the amount of filler you need on a clean, flat, non-absorbent surface, such as the plastic over-cap. Add the red hardener in the proportion given on the can, then mix thoroughly until the colour is completely even with no red or white streaks. As a guide from the manufacturer's mixing chart, 100g of filler with 2.5g of hardener gels in about 7 minutes at 22°C. Use less hardener if you need longer working time, particularly in warm weather. Press the mix into the repair with a putty knife or spatula, overfilling slightly. When it reaches the cheese-like stage, trim it to shape with a blade or surform. Allow about 30 to 60 minutes for a full cure, then sand and paint. Mix a small test batch first, because temperature and thickness change the set time.Important notesAlways follow the mix ratio on the can, because too little or too much hardener can affect the cure. Thick fills set faster than thin ones. Timber will still expand and contract with moisture changes, so good woodworking practice should still be followed around the repair. Mixed material generates heat as it cures. Do not leave mixed product in a pile or sealed container. Close the can tightly after use. Check the can and the supplied instructions for full details.Specifications Brand Turbo Product Builder's Bog timber repair filler Size 500ml can Colour Beige / buff paste Base Two part unsaturated polyester filler (cured with red hardener paste) Application Hand applied with a putty knife or spatula Gel time Adjustable by hardener amount; about 7 minutes in the 100g to 2.5g example at 22°C Full cure About 30 to 60 minutes Finishing Sandable, drillable and paintable Use Interior and exterior Country of manufacture New Zealand SafetyIt has a characteristic styrene odour. Use outdoors or in a well-ventilated area, avoid breathing vapours, and keep away from heat, sparks, open flames and other ignition sources. Keep the container tightly closed, out of reach of children, and stored in a dry place. Refer to the Safety Data Sheet (SDS) for full details.
$27.63
![Selleys Flexiseal FC Polyurethane Sealant & Adhesive 600ml Sausage [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-flexiseal-fc-polyurethane-sealant-adhesive-600ml-sausage-white-2.png?v=1792410682&width=645)
Selleys Flexiseal FC is a fast-curing polyurethane sealant and adhesive in white, supplied here as a 600ml sausage for sealing and bonding jobs around the building site or the house. It does two jobs in one product: it seals joints between common building materials and bonds them, and it stays flexible enough to cope with the movement those joints see through the seasons.About the formulaA single-component polyurethane with a non-slumping body, so it stays put in vertical joints instead of sagging. It is designed to grip common building surfaces without a primer, cures to a waterproof, flexible seal and can be painted once cured. Selleys rates it for joint movement of around plus or minus 25%.Where to use itIndoors: joints between wall and ceiling elements, around door and window frames, and acoustic rated walls, plus general bonding of building materials.Outdoors: weatherproofing joints between brickwork, masonry, concrete, timber or metal frames, sealing around roofing, retaining walls, external wall and cladding joints, and expansion joints.Suitable materials include concrete, brick, masonry, ceramic tile, metals, softwood and hardwood, plus some plastics (test other plastics and rubber first).How to use itMake sure the joint is clean, dry and free of dust, oil and other contaminants, and use a backing rod in deeper joints. Cut the end of the sausage, load it into a sausage-style applicator gun and extrude the sealant so it makes full contact with both sides of the joint, avoiding trapped air. Tool the surface smooth with a spatula before a skin forms. Once cured, it can be painted. For outdoor work, a suitable exterior paint will help the finish last longer.Important notesWill not adhere to polyethylene (PE), polypropylene (PP) or PTFE. Do not apply when the air or surface temperature is below 5°C. Not suitable for permanent water immersion or below water line use. Not intended for structural applications or general glazing. Avoid alcohol and solvent cleaners on the sealant while it cures, as they can interfere with the cure. Very damp substrates can cause bubbling in the sealant. It may affect the drying of oil or alkyd based paints, so test paint compatibility first. White sealant can yellow slightly with age and sun exposure. Store unopened sausages below 30°C in a cool, dry place out of direct sunlight, where they keep for around 12 months from manufacture. Opened sausages may skin over near the opening, so discard any lump or skin before using the rest.Specifications Brand Selleys Product Flexiseal FC Polyurethane Sealant & Adhesive Size 600ml sausage Colour White Base Polyurethane (single component) Application Sausage, via sausage gun Joint movement capability Plus or minus 25% Minimum application temperature 5°C Shelf life (unopened) About 12 months below 30°C Use Interior and exterior SafetyPolyurethane products can still irritate the skin, eyes and airways, so wear gloves and safety glasses, work with good ventilation and avoid prolonged skin contact. Store in a cool, dry, well-ventilated place away from heat, ignition sources and food, upright and tightly closed. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$32.06
SikaBond-142 Instant Nails is a high strength, multipurpose construction adhesive for panels, timber, metal and masonry, supplied here as a convenient 3 pack of 300g cartridges. It has a thick, non-slump body that stays put on vertical surfaces, and it can be used as a one-way liquid adhesive or as a two-way contact adhesive depending on the job.About the formulaA one-component, ready-to-use adhesive based on synthetic rubber, supplied in a solvent-based form and finished in a beige colour. It dries fast, grips firmly and can be painted over once cured. Sika's data sheet lists a tensile strength above 1 MPa on a dry substrate (tested to AS 2329) and a peel adhesion above 40 N. Once set, it is rated for service temperatures from 0°C to +40°C.Where to use itIndoors: floor and wall panels, skirting and other trim, and timber or board products bonded to timber, metal or masonry backgrounds.Outdoors: Sika's data sheet does not confirm exterior use or weather exposure, so check the data sheet and test a small area first if the bond will be exposed to the elements.Suitable materials include timber, particleboard, MDF and plywood, aluminium, iron and steel, concrete, cement sheeting, fibreglass and masonry. It is also commonly used on plasterboard. Always test a small area first on any surface you are unsure about.How to use it Make sure surfaces are clean, dry and free of dust, grease and loose material. Cut the cartridge nozzle and load it into a caulking gun. For a one-way bond, apply the adhesive to one surface and press the parts together firmly. For a two-way contact bond, apply to both surfaces and join them as directed on the pack. The adhesive begins to skin over in roughly 1 to 5 minutes, so have your parts ready and work promptly. Apply it between +5°C and +40°C substrate temperature. One cartridge covers roughly 15 linear metres with a continuous 5mm bead. Important notesFull cure takes approximately 7 days, depending on weather conditions. It is not suitable for immersed applications. Keep unopened cartridges in their original sealed packaging in dry conditions between +5°C and +25°C. Shelf life is 18 months from the date of production.Specifications Brand Sika Product SikaBond-142 Instant Nails Construction Adhesive Pack 3 x 300g cartridges Colour Beige Base One-component synthetic rubber, solvent-based Application Cartridge, via caulking gun Skinning time 1 to 5 minutes Full cure About 7 days Coverage About 15 linear metres per cartridge (5mm bead) Density About 1.1 kg/L Tensile strength Over 1 MPa on a dry substrate (AS 2329) Service temperature 0°C to +40°C Shelf life 18 months from production SafetyIt is also hazardous to aquatic life, so keep it out of drains and waterways. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Use it only outdoors or in a well-ventilated area. Wear protective gloves, clothing and eye protection. Refer to the Safety Data Sheet (SDS) for full details.
$16.04
Bondall Betta Tilecare Wet Area Waterproofer is a fast-curing, water-based liquid rubber membrane for sealing wet areas beneath tiles and renders, supplied here in a 10L pail for bigger bathroom, laundry and balcony jobs. It dries to a flexible, elastic film that acts as a water and vapour barrier, and it is designed to cope with permanently wet conditions, including ponding water once cured.About the formulaA water-based, one-part elastomeric membrane that is described by the manufacturer as non-toxic and non-flammable. It is classed as a Class III membrane under AS/NZS 4858 and, when used with the Betta detailing range, is designed to meet the Australian wet area requirements including AS 3740. The fast-curing formulation lets you tile or render over it quickly, and it is compatible with a range of tile adhesives, renders and toppings. No primer is needed on plasterboard or sound, dry concrete.Where to use itIndoors: bathroom and laundry floors and walls, shower recesses and other tiled wet areas, plus under screeds and toppings.Outdoors: balconies, decks, podiums and terrace floors, planters and retaining walls, and roofs that will be covered with screeds or toppings.Suitable substrates include concrete, screeds, renders, brick, plasterboard, fibre cement sheet and marine plywood. It sits under ceramic, porcelain, granite, marble and other stone tile finishes. Other surfaces, such as smooth, dense or damp ones, may need a Betta primer first, so check the technical data sheet for your substrate.How to use itMake sure the surface is sound, stable, clean and free of dust, oil, grease and loose material. Install the bond breaker and elastic joint band detailing first, as this is part of meeting AS 3740. Apply by brush, roller or spray unit in a minimum of two coats, changing direction between coats, to a total minimum coverage of 1.5 litres per square metre. This builds a dried film of roughly 1.2mm. Vertical or pitched areas can be done at around 1 litre per square metre. Take the membrane up walls at least 150mm in general wet areas and to 1.8m in shower recesses, finishing with a continuous, seamless film. Clean tools with water straight after use.Important notesTypical drying times at normal conditions (about 20°C, 50% humidity): tack free in about 45 minutes, recoat in about 1 hour, and ready to tile or topping over in about 4 hours. Retailer information quotes 6 hours before tiling, so allow the longer time in cool or humid weather and always follow the pack. Allow ample cure time before flood testing, as Bondall publishes more than one figure for this. Finish toppings must be water-based and solvent-free. Areas with rising damp or negative pressure should first be treated with Betta Damp Stop. Use on concrete slabs with hydrostatic or vapour pressure from below is outside the scope of the independent appraisal. Do not apply when rain is imminent. Always check the technical data sheet for your project.Specifications Brand Bondall (Betta Tilecare) Product Wet Area Waterproofer Pack 10L pail Base Water-based liquid rubber (elastomeric) Application Brush, roller or spray unit Coverage Minimum 1.5L per m2 over two coats (about 6.6 m2 per 10L pail) Dried film thickness Approx. 1.2mm Tack free About 45 minutes Recoat About 1 hour Tile or topping over About 4 to 6 hours (see notes) Standard AS/NZS 4858 Class III membrane Clean up Water Use Residential and commercial wet areas, interior and covered exterior SafetyEven so, wear gloves and eye protection, ensure good ventilation, and avoid contact with skin and eyes. Keep out of reach of children. Store in a sealed container in a cool place and protect from frost. Refer to the Safety Data Sheet (SDS) for full details.
$212.26
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
Selleys FlexiSeal (ProSeries) is a high-strength, fast-curing polyurethane sealant and adhesive built for tough construction jobs. It seals and bonds expansion and construction joints in both vertical and horizontal applications, staying highly flexible once cured so it can absorb the natural movement of a building without cracking or pulling away. This 600ml grey sausage pack suits a standard sausage gun and is ideal for larger trade and DIY jobs. Key features High-strength, flexible grey polyurethane adhesive and sealant Handles up to ±25% joint movement Non-slumping, low-modulus formula Fast curing and weatherproof for indoor and outdoor use Paintable after cure with no primer needed on most surfaces Excellent adhesion to most common building materials Where to use it Bonds and seals most building materials including concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics. Suitable for indoor and outdoor sealing of expansion and construction joints, around window and door frames, and general weatherproofing. How to use Prepare joints so they are clean, dry and free from oil, dust and curing agents. Use a backing rod for deeper joints. Cut the nozzle, load the sausage into a suitable gun and extrude the sealant, ensuring full contact with both joint sides and avoiding air entrapment. Tool and smooth off with a spatula. Once fully cured, paint if required using water-based paint. For solvent-based paints, undercoat with a water-based primer first. Important notes Applies and cures best at moderate temperatures (around 20°C), especially in cold weather. Will not adhere to PE, PP or PTFE; test other plastics and rubber before use. Not recommended for continuous submersion or below-water-line use. Not ideal over old or incompatible sealants, which may affect cure. Specifications Brand Selleys Product FlexiSeal (ProSeries) Multipurpose Sealant & Adhesive Technology Polyurethane joint sealant Colour Grey Size 600ml sausage Joint movement Up to ±25% Finish Paintable after cure Use Indoor and outdoor Safety Use in a well-ventilated area and avoid prolonged skin contact; wear suitable gloves and eye protection. Uncured polyurethane sealant may cause skin and eye irritation and can sensitise some users, so wash off any residue promptly. Keep out of reach of children. Always read the label and refer to the manufacturer’s Safety Data Sheet before use.
$27.25
Dunlop Tiler's Rubber Modified is a flexible, rubber modified tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). The rubber modified formulation gives the cured bond extra flexibility to absorb normal substrate movement, while its generous coverage and 6-hour grout time keep jobs moving. Classified C2S1, it is a dependable workhorse for tilers who need strength, flexibility and speed in one bag.Where to use itSuitable for indoor and outdoor walls and floors. It fixes ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, ceramic tile underlay, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can even be used over Dunlop Waterproofing and green concrete, making it handy on fast-track projects.How to useMix with clean water to a smooth, creamy consistency and allow to slake before remixing. Apply to a clean, sound, dust-free substrate using a 6 x 6 x 6mm notched trowel on walls or a 10 x 10 x 10mm notched trowel on floors. Press tiles in firmly with a twisting action and check adhesive transfer on the tile back. Grouting can begin in as little as 6 hours.Important notesNot suitable for moisture sensitive natural stone. Do not add extra water once the mix begins to stiffen, and avoid application in extreme temperatures.Specifications Size 20kg bag Colour Grey Coverage 14m² with 6mm notched trowel; 8m² with 10mm notched trowel Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, CTU, waterproofing, plasterboard, render Classification C2S1 tile adhesive; grout in 6 hours SafetyContains cement. Avoid generating and breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated space. Refer to the safety data sheet before use.
$47.18
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Express Wet Area Tape is a self-adhesive waterproofing joint tape that seals the most leak-prone parts of a wet area, the joints where floor meets wall, and around shower grates and outlets. Simply peel and stick: no messy fillets, no waiting for a bond breaker to cure. Paired with Dunlop Express Wet Area Waterproofing membrane it forms a rapid, complete waterproofing system that lets tiling commence just four hours after the membrane goes on.Where to use itSuitable for indoor and outdoor wet areas including bathrooms, showers, laundries and balconies. It performs over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard.How to useMake sure surfaces are clean, dry and dust-free. Peel the backing and press the tape firmly along floor/wall junctions, corners and around penetrations such as shower grates and outlets. Where two lengths of tape meet, overlap them by a minimum of 15mm. Then apply Dunlop Express Wet Area Waterproofing membrane over the taped joints and the rest of the area as normal.Important notesA standard shower recess with 1.8m high walls needs roughly 7m of tape, so one 10m roll comfortably covers a typical shower. Used with the Express membrane, the system meets Australian Building standards for wet area waterproofing.Specifications Size 80mm x 10m roll Colour Grey Overlap Minimum 15mm at joins Substrates AAC, fibre-cement, concrete, renders, screeds, wet area plasterboard SafetyLow-hazard adhesive tape; use care with cutting tools and follow the safety directions of the waterproofing membrane applied over it.
$65.28
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that delivers an instant waterproof seal across the joints where leaks start: the junction between floor and wall, and around shower grates and outlets in bathrooms, kitchens and laundries. It is the joint-sealing half of the Dunlop Pro Rapid system; team it with Dunlop Pro Rapid Waterproofing Membrane and tiling can commence just four hours after the membrane is applied, with the finished system meeting Australian Building standards for waterproofing.Where to use itDesigned for internal wet areas such as bathrooms, showers, kitchens and laundries. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheets, wet area grade plasterboard, plywood, internal AAC blocks and panels, concrete cured for a minimum of 28 days, and renders and screeds cured for a minimum of 7 days.How to useEnsure the surface is clean, dry and free of dust. Peel the release liner and press the tape firmly into floor/wall junctions, corners and around grates and outlets, smoothing out air bubbles as you go. Then apply Dunlop Pro Rapid Waterproofing Membrane over the tape and the remainder of the area to complete the system.Important notesSubstrate curing times matter: concrete needs at least 28 days and renders or screeds at least 7 days before taping and waterproofing. This tape is intended for internal applications and is designed to work as a system with the Pro Rapid membrane.Specifications Size 75mm x 15m roll System partner Dunlop Pro Rapid Waterproofing Membrane Tile after 4 hours (as part of Pro Rapid system) SafetyLow-hazard self-adhesive product; take care when cutting lengths and follow the safety directions on the membrane used over it.
$98.41
Dunlop Express Wet Area Waterproofing is a high performance, water-based acrylic polyurethane membrane built for speed. Its high-build consistency lets you brush on a thick, even film that reaches the required membrane thickness with ease, and when used with Dunlop Express Wet Area Tape you can start tiling just four hours later. This handy 1kg tub is ideal for small repairs, patching and touch-up work, and it is backed by a 10 year guarantee.Where to use itUse indoors or outdoors in wet areas: showers, bathrooms, laundries and balconies. It adheres to AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard on walls and floors.How to usePrime the clean, dry substrate, seal junctions and penetrations with Dunlop Express Wet Area Tape, then brush on the first coat of membrane. Once dry, apply a second coat at right angles to the first until the required thickness is achieved. Tiling can commence after 4 hours when the full Express system is used. Wash brushes in water immediately after use.Important notesWaterproofing has minimum application requirements under AS3740: after two coats the dry film must be 1mm thick on floors and 0.5mm on walls. Check local council specifications before you begin. The membrane is a Class III membrane to AS/NZS4858.Specifications Size 1kg tub Coverage Up to 0.84m² on walls or 0.42m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyVentilate the area, wear gloves and eye protection, and avoid skin contact. Keep away from children and consult the Safety Data Sheet before use.
$43.00
Dunlop Express Wet Area Waterproofing in the 20kg pail is the full-bathroom format of Dunlop's fast-track membrane. This high performance, water-based acrylic polyurethane formula offers superior workability and a high-build film that reaches the required thickness without endless coats. Combined with Dunlop Express Wet Area Tape, the system lets tiling commence in as little as four hours, and it carries a 10 year guarantee.Where to use itMade for indoor and outdoor wet areas: showers, bathrooms, laundries and balconies. Apply it over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard, on walls and floors.How to usePrime the substrate with the appropriate Dunlop primer, seal all floor/wall junctions, corners and penetrations with Dunlop Express Wet Area Tape, then brush the membrane on generously. When the first coat is dry, brush on a second coat at right angles to the first to build the required film thickness. Tiling can begin after 4 hours when the complete Express system is used. Tools clean up in water while wet.Important notesAS3740 requires a minimum dry film thickness after two coats of 1mm on floors and 0.5mm on walls; confirm requirements with your local council. Certified as a Class III membrane to AS/NZS4858 and conforming to AS3740-2010 Wet Area Membranes.Specifications Size 20kg pail Coverage Up to 17m² on walls or 8.5m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyWork with good ventilation, wear gloves and safety glasses, and avoid contact with skin and eyes. Store sealed, away from children, and read the Safety Data Sheet first.
$313.95
Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.
$67.73
Dunlop Ardit Crack Filler is a high strength, two-part hybrid polyurethane that repairs cracks and spalls in concrete almost instantly. With a viscosity similar to water, it flows deep into cracks that pastes and mortars can't reach, then cures harder than the surrounding concrete within an hour. Driveable repairs are possible in as little as 20 minutes, making it a genuine problem-solver for busy floors and driveways.Where to use itSuitable for indoor and outdoor concrete - garage floors, driveways, paths, warehouse slabs and patios. Because the two parts mix automatically through the nozzle, it is equally at home in a professional toolkit or a weekend repair kit.How to useClean the crack thoroughly, removing dust, loose material and any moisture. Load the 254ml dual cartridge into a suitable applicator gun, attach the self-mixing nozzle and dispense directly into the crack until full. For wider spalls and larger repairs, blend in clean, dry bagged aggregate to bulk the fill. The repair sets stronger than concrete in about 1 hour and takes vehicle traffic after roughly 20 minutes.Important notesNew concrete must be fully cured - at least 28 days old - before application. The water-thin consistency is designed for penetrating cracks, so dam or tape the ends of through-cracks where needed. Used nozzles cannot be reused once the product sets.Specifications Size 254ml dual cartridge Coverage Depends on crack width and depth Thickness Flows to full crack depth; add aggregate for large voids Substrates Concrete Set time Drive on after 20 minutes; full strength in 1 hour SafetyReactive polyurethane resins can irritate skin and airways before curing. Wear nitrile gloves and safety glasses, work in a well-ventilated area, avoid skin contact with uncured product and keep it away from children. Dispose of cartridges according to local regulations.
$67.48
Dunlop Builder's Bond is a high strength, multipurpose, rapid-cure epoxy bonding and repair system that joins almost any building material to almost any other. Dispensed through a self-mixing nozzle from a convenient 254ml dual cartridge, its non-sag formula holds firm on walls and even overhead, and cures stronger than concrete in about 2 hours.Where to use itSuitable for indoor and outdoor use across floor, wall and overhead repairs. Typical jobs include bonding concrete, masonry, stone, metal and timber components, rebuilding broken edges and corners, anchoring fixtures, and general structural gap filling where a fast, very strong bond is required.How to useEnsure both surfaces are clean, dry and free of dust, grease and loose material. Load the cartridge into an applicator gun, fit the self-mixing nozzle and dispense the evenly mixed epoxy directly onto the repair or bond line. Shape and tool it before it stiffens. Once cured, Builder's Bond can be shaped, sanded, drilled and painted, so repairs can be blended invisibly into the surrounding surface.Important notesNew concrete must be fully cured - a minimum of 28 days old - before bonding. The non-sag consistency suits vertical and overhead work but is not a pourable grout. Start a fresh nozzle for each session, as mixed product hardens inside the nozzle.Specifications Size 254ml dual cartridge Coverage Depends on bead size and gap width Substrates Concrete, masonry, stone, metal, timber and most building materials Set time Stronger than concrete in 2 hours Finish Sandable, drillable and paintable once cured SafetyUncured epoxy resins and hardeners can cause skin irritation and sensitisation. Wear nitrile gloves and eye protection, ventilate the work area, avoid skin contact and wash immediately if contact occurs. Keep cartridges sealed and out of reach of children.
$61.79
Dunlop Ardit Feather Finish is a cement-based smoothing compound that skims internal floors to a super-smooth, permanent finish before floor coverings are installed. Powered by ARDEX Ardit technology, it trowels out to a true feather edge and sets so fast that coverings can be applied from just 15 minutes after placement - and it needs no primer on most surfaces, saving a whole step.Where to use itFor indoor use over concrete, existing tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. It is ideal for filling grout joints when covering old tiles with vinyl, smoothing trowel marks in levellers, and taking out minor imperfections before vinyl, carpet or ceramic tiles.How to useEnsure the floor is clean, sound and free of dust, grease and loose material. Mix the powder with clean water to a smooth, creamy paste and apply with a flat steel trowel, working from a feather edge up to 3mm thick. Tight second coats can be applied as the first firms. Any ridges can be shaved or lightly sanded once set for a flawless surface.Important notesIndoor use only and must be covered by a floor covering. Mix small batches to suit the rapid set. No primer is required over common substrates - check the datasheet for unusual surfaces.Specifications Size 3.5kg bag Coverage Approx. 12m² over concrete or 24.5m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyCement powders can irritate eyes, skin and lungs. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated, avoid prolonged contact with the wet compound and wash hands after use. Store out of reach of children.
$82.46
Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications Size 8kg bag Coverage Approx. 27m² over concrete or 55m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.
$125.51
Dunlop Ardit Rapidset Repair Mortar in the 10kg bag gives tradies and serious renovators a bigger supply of this extremely fast-hardening construction mortar. Built on ARDEX Ardit technology, it patches cracks, holes and broken edges and is trafficable after only 45 minutes, with floor coverings able to go down just 1 hour after placement - ideal when repairs can't shut an area down for long.Where to use itUse indoors and outdoors on concrete, render, screeds, masonry, plasterboard, timber and fibre-cement sheet. Typical jobs include patching worn slabs before flooring, building small ramps and transitions, and making good around doors, windows and plumbing work internally.How to usePrepare a clean, sound, dust-free repair area. Mix approximately 3L of clean water with the 10kg of powder to a smooth mortar, then trowel firmly into the repair, compacting well and finishing flush. Apply from a feather edge up to 20mm per pass, building deeper repairs in stages. Working time is about 15 minutes, so mix in manageable batches.Important notesDo not re-temper the mix with extra water once it begins to stiffen. Suited to patch repairs rather than full-floor levelling - pair it with a Dunlop floor leveller for whole-room work. Covered by a 10 year guarantee when used as directed.Specifications Size 10kg bag Coverage Varies with patch depth; feather edge to any thickness Thickness Feather edge up to 20mm per application Substrates Concrete, render, screeds, masonry, plasterboard, timber, fibre-cement Walk-on time 45 minutes (floor coverings after 1 hour) SafetyContains cement - alkaline when wet. Wear gloves, eye protection and a P2 dust mask during mixing, work in a ventilated space, avoid skin contact and rinse any splashes promptly. Keep out of reach of children.
$60.93
Dunlop Ardit Floor Leveller is a premium cement-based levelling compound built on the renowned Ardit Technology from ARDEX. It offers superior flow and workability, spreading easily across uneven concrete to create a smooth, even surface before new floor coverings go down. Floors are walkable in around 3 hours and ready for ceramic tiles in the same timeframe, keeping renovation and re-flooring jobs moving quickly.Where to use itUse indoors and outdoors under covered areas over sound concrete floors, ahead of ceramic tiles, carpet or vinyl. It is designed for concrete substrates only and must be protected by a floor covering rather than left exposed to the weather or used as a finished wear surface.How to useEnsure the slab is clean, sound and primed as required. Mix each 20kg bag with approximately 4.5L of clean water using a low-speed paddle mixer until smooth and lump free. Pour and spread with a trowel, letting the compound flow out and level itself. Apply from a thin skim up to 25mm in one pass, adding 2-5mm aggregate for deeper fills.Important notesNot suitable for driveways or areas subject to vehicular traffic. Vinyl and carpet can be laid after about 24 hours, while tiles can go down after roughly 3 hours. Refer to the technical datasheet for priming guidance on porous slabs.Specifications Size 20kg bag Coverage Approx. 12m² at 1mm or 4m² at 3mm per bag Thickness 1-25mm per application Substrates Concrete Walk-on time 3 hours (tiles 3 hours; vinyl and carpet 24 hours) SafetyContains cement, which is alkaline when wet. Wear gloves, eye protection and a P2 dust mask while mixing, ensure good ventilation, avoid skin contact and rinse promptly if the mix touches skin or eyes. Store away from children.
$67.45
Dunlop Multipurpose Floor Leveller is a cement-based levelling compound from Dunlop Trade (ARDEX Australia) that mixes with water into a smooth, free-flowing material for evening out rough or uneven concrete floors. It flows into low spots and finds its own level, leaving a flat base that is ready for foot traffic in around 2 hours and ready for tiles in about 4 hours, making it a dependable first step before laying new floor coverings such as carpet, vinyl or ceramic tiles.Where to use itSuitable for indoor and outdoor use over sound concrete floors, including living areas, kitchens, laundries and covered patios. It can also be used to form ramps or for bulk filling. It is designed for concrete substrates only and must always be covered by a finished floor covering.How to usePrepare the slab so it is clean, sound and free of dust or contaminants, and prime porous surfaces. Slowly add the powder to clean water while mixing with a low-speed paddle mixer for 2-3 minutes until lump free. Pour onto the floor, spread with a trowel and allow it to self-smooth. Apply up to 25mm in one application, adding 2-5mm aggregate for beds thicker than about 10mm.Important notesNot suitable for driveways or areas with vehicle traffic, and it cannot be left exposed as a wear surface. Sand can be added to create a trowelable screed for ramping. Always follow the technical datasheet for priming and mixing details.Specifications Size 15kg bag Coverage Approx. 1.6kg/m² per mm (about 9m² at 1mm per bag) Thickness Up to 25mm per application Substrates Concrete Walk-on time 2 hours (tiles after 4 hours) SafetyCement-based powders are alkaline and can irritate skin, eyes and airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in a ventilated area, wash skin after use and keep out of reach of children.
$69.96
For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: abrade and degrease the surfaces first for a stronger, more durable bond. Loxeal 31-42 Clear 5-Minute Epoxy Adhesive 50ml Dual Cartridge Loxeal 31-42 is a two-part, fast-setting structural epoxy that cures colourless and transparent, making it ideal for repairs where the glue line needs to stay invisible. Supplied in a convenient 50ml dual cartridge (1:1 ratio) with a mixing nozzle, it dispenses perfectly proportioned adhesive with no weighing or hand mixing. With a working time of around 5 minutes and handling strength in 20–30 minutes, it bonds metals, ferrite, ceramic, marble, glass, concrete, wood and some rigid plastics. Why choose Loxeal 31-42? Dries clear – colourless, transparent bond line suits glass, ceramics and visible repairs Fast 5-minute set – 3–8 minute working time, functional strength in 20–30 minutes No-mess 1:1 dual cartridge with mixing nozzle for accurate, on-part dispensing Gap filling from 0.1 to 2.0 mm for less-than-perfect joints Durable bonds with excellent resistance to water, gasoline, motor oil and cooling gas Easy enough for DIY, strong enough for the workshop Typical applications Structural bonding of metals, ferrite, ceramic, marble, glass, concrete and wood Bonding some rigid plastics such as polyester, ABS and rigid PVC Joining dissimilar materials in one fast operation Household, automotive, hobby and workshop repairs needing a clear, rigid bond How to use Lightly abrade the surfaces, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the cartridge and discard the first 3–5 cm of extruded adhesive. Apply the mixed adhesive directly to one surface. Assemble the parts immediately and hold them together, without mechanical stress, until handling strength is reached. Remove uncured excess with acetone or a compatible solvent-based cleaner; cured adhesive can only be removed mechanically. Cure times Pot life (working time): 3–8 minutes at +25°C Functional cure: 20–30 minutes at +25°C Strength continues to develop over the following hours; gentle heat accelerates cure Specifications Chemistry Two-part epoxy (resin / amine hardener) Colour (mixed) Colourless / transparent Mixing ratio 1:1 by volume Pot life (+25°C) 3–8 minutes Functional cure 20–30 minutes Shear strength (steel, ISO 4587) 12–14 N/mm² Peel strength (ISO 4578) 4–20 N/25mm Hardness Shore D 65–75 Gap fill 0.1–2.0 mm Service temperature -40°C to +80°C Pack size 50ml dual cartridge (DCT) with mixing nozzle Shelf life 1 year unopened at +5°C to +25°C Important notes Not suitable for rubber, soft materials, polyethylene (PE), polypropylene (PP) or PTFE Apply at temperatures above +15°C; higher temperatures shorten pot life Avoid mixing large volumes at once – the chemical reaction generates heat Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Work in a well-ventilated area, avoid skin and eye contact, and keep out of reach of children. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.
$73.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 100g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. This 100g workshop bottle is the economical choice for production lines, maintenance teams and busy workshops that go through super glue regularly. Why choose Loxeal Istant 23? Trade-size 100g bottle – keeps high-use workshops and production benches running Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Solvent-free, single part – clear cure with tensile strength of 12–25 N/mm² Typical applications Production assembly and repetitive bonding tasks O-rings, seals and neoprene/NBR rubber components Maintenance and repair across rubber, metal and plastic parts Workshops and trades that need a reliable everyday instant adhesive in volume How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 100g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$135.00
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 25 Super Glue Medium Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 25 is a medium-to-high viscosity super glue based on ethyl cyanoacrylate, designed for bonding plastic, rubber, metal and ceramic – including slightly irregular surfaces where a runny glue would simply drain away. At 350–450 mPa·s it stays where you put it, fills gaps up to 150 microns and fixtures in seconds, with a medium setting speed that gives you a moment to position parts. Supplied in a 20g bottle. Why choose Loxeal Istant 25? Medium viscosity – controllable application that stays put on the joint Handles imperfect surfaces – fills gaps of 10–150 microns Broad substrate range – plastic, rubber, metal and ceramic with one product Fast, strong fixture – tensile strength of 15–23 N/mm² when cured Solvent-free, single part – clean, clear bond line with no mixing Typical applications Repairs on ceramics, ornaments and household items Bonding rubber and plastic parts with less-than-perfect mating surfaces Metal-to-plastic and metal-to-rubber assemblies General workshop, trade and hobby bonding How to use Clean and degrease both surfaces and allow them to dry fully. Apply a modest bead or drops to one surface only. Assemble the parts promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; phenolic resin 5–20 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 350–450 mPa·s (medium) Gap fill 10–150 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 15–23 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$24.95
For best performance, pair with these Loxeal products: Loxeal Activator 9: accelerates cure to just 1 to 4 seconds on slow, dry or porous surfaces, and sets excess adhesive instantly. Loxeal Primer 7: needed to bond polyolefins such as polypropylene (PP), polyethylene (PE), PTFE, silicone and EPDM. Loxeal Istant 43 Speciale Super Glue Cyanoacrylate Adhesive 50g Loxeal Istant 43 Speciale (43S) is a surface-insensitive, general purpose super glue based on modified ethyl cyanoacrylate. Unfazed by acidic and porous surfaces, it excels at bonding leather, wood, fabric, ceramic and metals where ordinary super glues struggle. It offers proven heat resistance to +120°C (short peaks to +150°C) and is NSF registered for use in and around food processing areas, making it a favourite for demanding trade and industrial work. Supplied in a 50g bottle. Why choose Loxeal Istant 43 Speciale? Surface insensitive – cures reliably on acidic and porous substrates like leather, wood and paper Heat resistant – holds strength up to +120°C, with short-term peaks to +150°C NSF registered – acceptable for use as an instant adhesive in and around food processing areas Very fast on hard-to-glue materials – fabric in 2–20 seconds, leather in 5–15 seconds Strong all-rounder – medium viscosity with tensile strength of 15–25 N/mm² Typical applications Leather goods, footwear and upholstery repairs Woodworking, trim and joinery fixes across many timber species Equipment maintenance around commercial kitchens and food processing plants Fabric, ceramic, metal and rubber bonding in workshops and on site How to use Clean and degrease all surfaces and allow them to dry before applying the adhesive. For low-energy plastics such as PE, PP or PTFE, apply Loxeal Primer 7 first and let it dry. Apply the adhesive sparingly to one surface, then bring the parts together quickly and correctly aligned – the fast cure leaves little room for repositioning. Press firmly for a few seconds until fixed, and keep parts clamped until fully set. Wait 24–72 hours for full cure before applying any mechanical stress. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: paper 1–5 seconds; fabric 2–20 seconds; PVC, ABS and phenolic resin 2–10 seconds; aluminium 2–10 seconds; steel 5–20 seconds; leather 5–15 seconds; ceramic 5–30 seconds; softwoods 5–20 seconds; oak 90–180 seconds. Loxeal Activator 9 can be used to accelerate slow joints. Full cure in 24–72 hours. Specifications Chemistry Modified ethyl cyanoacrylate Colour Clear Viscosity (+25°C) 80–150 mPa·s (medium) Gap fill 10–150 microns Fixture time 1–180 seconds, substrate dependent Full cure 24–72 hours Tensile strength 15–25 N/mm² (ISO 6922) Service temperature -50°C to +120°C (peaks to +150°C) Approvals NSF registered for food processing areas Shelf life 12 months in original unopened packaging Pack size 50g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Not approved for use with pure or gaseous oxygen. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.
$57.95
You have seen 144 out of 288 products
Reduced set times to speed assembly without sacrificing strength. Great when you need parts handled or clamped for only minutes. Match working time and viscosity to your joint design (thin vs gap-fill). Use filters to refine by chemistry, pot life and temperature rating. Always review the product page and TDS/SDS before use.
