The Big Cheese Sonic Pest Repeller is a small plug-in rodent deterrent that helps keep mice and rats out of living areas without baits, traps or chemicals. It runs around the clock and is compact enough to sit discreetly in a room, kitchen or garage while delivering the same output as the brand's larger units.About the productThe unit gives off ultrasonic sound waves that humans and non-rodent pets such as cats and dogs cannot hear, but that sit within the hearing range of mice and rats. This creates an unwelcome environment for rodents so they move on to look for somewhere else to live. It is a welfare-friendly, poison-free option that suits areas where baits are not appropriate, such as around food preparation spaces.Where to use itIndoors: living areas, kitchens, sheds and garages with a power point available.Outdoors: not suitable for outdoor use.How to use it Plug the unit straight into a power point and switch it on. No batteries are needed. Use one repeller per room for the best results. Leave it running while you deal with an infestation, then keep it going as a preventative measure to discourage rodents from returning. Position it where sound can travel freely, as ultrasonic waves are easily blocked by furniture, curtains and other solid objects. Important notesDo not use it around pet rodents such as guinea pigs, hamsters, gerbils or rabbits, as they can hear the sound. It is designed for indoor use only and should be kept dry. A repeller is a deterrent, so for an existing heavy infestation it is best used alongside other control methods.Specifications Brand The Big Cheese Product Sonic Pest Repeller Model number 71032 Pack Single unit Colour White Material Plastic Method Ultrasonic (sonic) Target pests Mice and rats Power Plug-in, mains powered Use Indoor only Care and storageUnplug the unit before moving or cleaning it, and wipe it with a dry or barely damp cloth. Keep it away from moisture, and do not use it outdoors. Keep out of reach of young children when not plugged in, and store it in a cool, dry place when not in use.
$23.30
The Adoored Fabric Draught Stopper is a simple, good-looking way to close the gap under an interior door, supplied as a single stopper in your choice of Charcoal, Grey or Brown. It sits along the base of the door to limit outside air coming in and conditioned air escaping, which can help your heating and cooling work less hard.About the productThis is a fabric-covered door draught stopper made for interior doors. The fabric is hard-wearing yet neat in appearance, so it blends in with most home and office decor. It is designed to move with the door when the door is pushed, so you are not tripping over it or dragging it out of position every time you pass through.Where to use itIndoors: along the bottom of interior doors in bedrooms, living areas, hallways, home offices and similar spaces where you want to cut down on draughts and help hold in warm or cool air.Outdoors: not intended for exterior use. It is made for interior doors only.How to use it Position the stopper along the base of the door so it covers the gap between the door and the floor. Check that the door still opens and closes freely over your flooring before relying on it. Choose the colour that best suits your door and floor: Charcoal, Grey or Brown. Sold individually, so order one for each door you want to seal. Important notesColour is selected at the time of ordering and each unit is sold on its own, not as a multipack. It is designed for interior doors, so it is not a substitute for a weather seal on exposed external doors. Very large or uneven gaps may not be fully covered, so measure your door width and the gap before buying.Specifications Brand Adoored Product Fabric Draught Stopper Model number T1011 Pack Single stopper Length Approx. 830 mm Material Fabric Colours Charcoal, Grey, Brown Door type Interior Use Interior only Care and storageKeep the stopper clean and dry, and brush or vacuum off dust and pet hair as needed. Spot clean marks gently and avoid soaking the fabric. Store flat and away from damp areas when not in use.
$11.48
Combat Ant-Rid Ant Baits are a tidy, ready-to-use indoor ant control option, supplied here as a six-pack of 1.5g bait stations for kitchens, bathrooms and other trouble spots. The baits are made to work on the nest, not just the ants you can see, so you can deal with a stubborn indoor ant problem without sprays or mess.About the formulaEach bait uses a delayed-action formula with the active ingredient fipronil. It combines a sweet food source with a protein food source to attract foraging worker ants. The delay gives workers time to carry the bait back to the nest and share it with other ants, including the queen, before the bait takes effect. The grey station design is meant to blend in with kitchen and bathroom surfaces.Where to use itIndoors: kitchen benches and cupboards, under sinks, behind appliances, bathrooms, laundries and other spots where ants are trailing.Outdoors: not intended for outdoor use.Designed for common household ants. Place the baits on dry, clean, flat surfaces close to ant trails.How to use itTake the baits out of the pack and place them right beside ant trails or where ants gather. The stations need no activation. For best results, put out several at once and keep the surrounding area clear of food crumbs and spills. Leave the baits and the ants alone so the workers can carry the bait back to the nest. Where the pack includes adhesive tabs, you can use them to fix stations to walls or under benches. Replace stations once they have been eaten, or as directed on the pack.Important notesAnt activity can rise at first as workers find the bait, then ease off as the bait is carried back to the nest. Do not spray other insecticides on or near the baits, as this can put ants off. Not suitable for outdoor use. Different ant species prefer different foods, so results can vary. Keep baits away from food preparation areas and where children or pets can reach them.Specifications Brand Combat Product Ant-Rid Ant Baits Pack 6 x 1.5g baits Colour Grey Active ingredient Fipronil Food sources Sweet and protein Target pest Ants Application Ready-to-use bait stations, no activation needed Use Indoor use only SafetyUse as directed on the pack. Keep out of reach of children and pets, and do not handle the baits more than necessary. Wash your hands after use and keep the baits away from food and drink. Store unused packs in a cool, dry place out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$11.30
Syneco Self-Adhesive Door and Window Weather Seal is a soft black EPDM rubber strip that helps cut down draughts, dust and noise around doors and windows. It comes as 5 metres in total, supplied as two 2.5 metre lengths, so it suits a few average-sized openings around the home.About the productThe strip is made from soft, flexible EPDM rubber and has a self-adhesive backing, so there is no separate glue to buy or mix. It is designed to sit in the corner between the door or window stop and the frame, where it compresses to form a seal. The profile is 9mm wide and 6mm high, and it is suited to gaps of about 3 to 6mm.Where to use itIndoors: around internal door and window frames where you want to reduce draughts, dust and noise.Outdoors: this product is described as being for interior use, so it is not recommended for exposed outdoor locations.How to use it Measure the gap you want to seal first. The strip suits gaps of roughly 3 to 6mm. Clean the frame surface so it is free of dust, grease and loose paint, and let it dry fully. Cut the strip to length with sharp scissors or a utility knife. Peel back the protective liner a little at a time and press the strip firmly into the corner between the stop and the frame. Close the door or window gently to check that the seal compresses evenly without making it hard to close. Important notesCheck that your gap sits within the 3 to 6mm range before you buy, as a seal that is too thick can make a door or window hard to close. Self-adhesive strips bond best to clean, dry, sound surfaces. Test a short length on your frame first if it has a textured or freshly painted finish.Specifications Brand Syneco Product Self-Adhesive Door and Window Weather Seal Model number SY-130605 Pack 2 x 2.5m lengths (5m total) Profile 9mm wide x 6mm high Colour Black Material EPDM rubber Suitable gap 3 to 6mm Fixing Self-adhesive backing Use Interior Care and storageKeep the strip in its packaging in a cool, dry place until you are ready to fit it, and keep the adhesive face covered so it stays clean. Wipe the installed seal with a damp cloth when needed. Avoid harsh solvents, which can affect the rubber and the adhesive.
$5.56
The Envirosafe Indoor Mosquito Trap is a compact, USB-powered trap that helps clear mosquitoes from living areas and bedrooms without sprays, coils or pesticides. It uses light and gentle suction to catch insects quietly, and it doubles as a soft night lamp when you want one.About the productThe trap has low-power UVA LEDs that give off a blue light mosquitoes are drawn to. A whisper-quiet fan then pulls them down into a storage tray inside the unit, where they can't escape. It is a chemical and pesticide free approach, so there is nothing to refill or replace. A built-in light sensor lets the trap switch itself on only at night if you prefer. A single soft-white LED lamp can be used as a night light.Where to use itIndoors: bedrooms, living areas, kitchens and near indoor plants, where mosquitoes tend to rest during the day. Running it in the bedroom for a few hours before bed helps reduce mosquitoes before you go to sleep.Outdoors: designed for indoor use only.How to use it Plug the supplied USB cable into any USB outlet, such as a power point adaptor, computer or power bank. Press the ON/OFF button to start the lights and fan. Leave the low-light sensor uncovered if you want the trap to run only in the dark, which saves power if night-biting mosquitoes are your main problem. Switch the trap off at the power before removing the storage tray, then empty out the trapped insects. The brand suggests checking the tray every few weeks to monthly. Wipe the outside with a damp cloth to remove dust when needed. Important notesThis trap is designed for indoor use only. It catches adult mosquitoes that come near the light and fan, so it works best alongside sensible measures such as keeping doors and screens closed. It may also catch small moths and flies. Read the user manual supplied with the trap before first use.Specifications Brand Envirosafe Product Indoor Mosquito Trap Pack 1 trap with USB cable Power USB Light source Low-power UVA LEDs plus a soft-white night lamp Controls ON/OFF button, low-light sensor for night-only operation Product size 125 x 125 x 215 mm (W x D x H) Use Indoor only Care and storageKeep the trap in a dry spot away from water and out of reach of young children. Turn it off at the power before emptying the tray, and wipe it over with a damp cloth to remove dust. Keep the user manual for full instructions and safety guidelines.
$57.11
FrogTape Delicate Surface Painter's Tape is a premium yellow washi paper masking tape for crisp paint lines on surfaces that can't cope with a stronger tape, supplied here as a single 24mm x 55m roll. Its lower adhesion level helps protect finishes such as freshly painted walls, coated wallpaper and decorative paint work, making it a sensible pick for stripes, feature walls and detailed edging.About the formulaThe tape has a thin washi paper backing and a synthetic rubber-based adhesive with low adhesion. The edges are treated with PaintBlock Technology, a super-absorbent polymer that reacts with the water in latex paint and gels into a micro-barrier along the tape edge. This seals the edge against paint bleed so the paint line stays sharp and the need for touch-ups is reduced. The manufacturer describes the adhesive system as solvent-free, and the tape is designed to come away cleanly from indoor surfaces for up to 60 days.Where to use itIndoors: masking trims, skirting, door and window frames, cabinets and feature walls, plus decorative work such as stripes, faux finishes and artwork.Outdoors: not recommended. This tape is intended for interior use only.Recommended surfaces include finished wood, fresh paint, coated wallpaper, veneer, laminate, vinyl and primed drywall. Always test a small hidden area first to confirm compatibility with your surface and coating.How to use itMake sure the surface is clean, dry and free of grease, oil and dust. Press the tape down firmly along the edge so it sits flat, then paint with a latex paint, which is what PaintBlock Technology is designed to work with. For the sharpest result, peel the tape away while the paint is still wet, pulling back at a low angle. Store the roll in a cool, dry place away from direct sunlight.Important notesAllow freshly painted surfaces to dry before taping. The manufacturer's guidance is a minimum of 24 hours, so check the paint label as well. Test before use with solvent-based coatings, and check that it suits your floor surface before masking floors. Unprimed drywall is not recommended. For the cleanest removal, take the tape off promptly after painting rather than leaving it in place for the full 60 days.Specifications Brand FrogTape Product Delicate Surface Painter's Tape (CF 160) Pack 1 roll, 24mm x 55m Colour Yellow Backing Washi paper Adhesive Synthetic rubber-based, low adhesion Thickness 0.08mm Maximum application temperature 93°C Clean removal Up to 60 days (indoor surfaces) Technology PaintBlock edge sealing for latex paint Use Interior only SafetyUse with normal care. Cut or tear the tape with suitable tools and keep blades away from children. Keep out of reach of children and store the roll in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$13.47
Velcro Brand Stick On Dots are a tidy, tool-free way to hang and hold lightweight items indoors, supplied here as a 40 pack of black 22mm adhesive-backed hook and loop dots. They give you a simple alternative to nails, screws, glue and tape for small jobs around the home, office, classroom or craft table.About the productEach dot is a preformed, round piece of nylon hook or loop with a peel-and-stick adhesive backing, so there is nothing to measure, cut or mix. The hook and loop halves grip together firmly and can be pulled apart again when you need to take the item down. The nylon construction is durable and made for everyday indoor use.Where to use itIndoors: hanging notices, message boards, signs, posters and lightweight artwork, parking remote controls and small tools, labelling and organising storage containers, and attaching items in craft, scrapbooking and school projects.Outdoors: not recommended, as prolonged exposure to direct sunlight and the elements can damage the fastener.Best on smooth, clean, dry indoor surfaces such as timber, metal, glass, tiles, cardboard, painted walls and many plastics (test plastics first, as the dots may not grip every plastic).How to use itMake sure the surface is smooth, clean and dry. Peel the backing from a loop dot, position it and press down firmly to activate the adhesive. Repeat with a hook dot on the item you are mounting, then press the two together. Leave about 15 minutes before putting the dots to work.Important notesThe adhesive reaches its maximum strength after about 24 hours. Application works best at room temperature, roughly 18 to 24°C. Test a small area first if you are unsure about the surface. Moving a dot after it has been stuck down weakens the adhesive and may mark the surface, so position carefully. Not recommended for fabrics, flexible vinyl, PVC, wallpaper, loose or flaking paint, porous surfaces, wet areas or underwater use. Intended for lightweight items only.Specifications Brand Velcro Brand Product Stick On Hook and Loop Dots (Sticky Back) Pack 40 dots Dot size 22mm Colour Black Material Nylon hook and loop Backing Self-adhesive, peel and stick Application By hand, no tools required Full adhesive strength About 24 hours Use Indoor only SafetyUse as directed on clean, dry surfaces and keep the dots away from small children, as they are small parts. Store in a cool, dry place in the original pack. Refer to the Safety Data Sheet (SDS) for full details.
$20.87
Velcro Brand Heavy Duty Hook and Loop Tape is a peel-and-stick fastening system for securing heavier items indoors without nails, screws or drilling, supplied here as a 2 pack of black 50 x 100mm pieces. It pairs a moulded plastic hook with a low profile loop to give a slim, strong closure that suits garage, workshop, office and storage organising.About the productThe hook is moulded and the loop is woven nylon, so the two faces interlock into a thin, firm closure. The low profile design is about 30% thinner than standard Extreme Duty fasteners. Each piece has a self-adhesive backing, and the hold is rated at up to 675g for every 25 x 25mm square of tape, so you can cut or size the fastening to suit the load.Where to use itIndoors: tools and equipment on shed or garage walls, organisers and storage items in workshops and offices, and other heavier lightweight-to-medium items on smooth, clean surfaces.Outdoors: not recommended. Prolonged exposure to direct sunlight and the elements can damage the fastener, and it is not intended for wet areas.Suitable surfaces include smooth, clean and dry painted wallboard, glass, metal and most plastics. Test plastics first, as the tape may not adhere to every plastic.How to use itMake sure the surface is smooth, clean and dry. Cut the tape to the length you need if required, peel off the backing and position it on the surface. Press down firmly to activate the adhesive, then leave it for 24 hours before loading it with weight. The best application temperature is roughly 18 to 24°C.Important notesThe adhesive reaches its maximum strength after about 24 hours. Moving the fastener after it has been stuck down weakens the adhesive and may damage the surface, so position it carefully the first time. Not recommended for laundered fabrics, PVC, wallpaper, loose paint, or porous or flaking surfaces. Not suitable for wet areas. Operating temperature range is -18°C to 49°C.Specifications Brand VELCRO® Brand Product Heavy Duty Hook and Loop Tape (Stick On) Model VL25554 Size 50 x 100mm Pack 2 pack Colour Black Material Nylon hook and loop Application Peel and stick, applied by hand Holding power Up to 675g per 25 x 25mm square Full adhesive strength About 24 hours Operating temperature -18°C to 49°C Use Indoor SafetyUse with normal care and keep the tape away from young children. Apply to clean, dry surfaces and avoid fixing items overhead or above people where a fall could cause injury. Store in a cool, dry place in the original pack. Refer to the Safety Data Sheet (SDS) for full details.
$11.54
Velcro Brand Stick On Hook and Loop Tape in black is a cut-to-length, peel-and-stick fastener that lets you hang, attach and organise lightweight items indoors without nails, screws or glue. It suits home, office and classroom jobs where you want a neat, tool-free fixing on a smooth surface.About the formulaA nylon hook and loop set with an adhesive backing on each side. You cut a length off the 25mm wide, 1m roll to match the job, peel away the backing and press it into place. The hook and loop faces press together to form a fastener you can open and close repeatedly. The black finish blends in on most surfaces.Where to use itIndoors: displaying posters, signs, prints and artwork, labelling storage containers, keeping frequently used items within reach, and light craft or display projects.Outdoors: not recommended. Prolonged exposure to direct sunlight and the elements will damage the fastener.Suited to smooth, clean, dry indoor surfaces such as wood, metal, glass, cardboard and plastic (test plastics first, as the adhesive may not grip every type).How to use itClean and dry the surface first so it is free of dust, grease and moisture. Cut the tape to the length you need, remove the backing from the hook and loop pieces, and press them firmly onto both surfaces. For best adhesion, apply at room temperature, ideally between 18 and 24°C. Test a small area first if you are unsure about the surface.Important notesThe adhesive reaches its maximum strength after about 24 hours, so allow time to set before putting weight on it. This general-purpose tape is intended for lightweight items. Not recommended for laundered fabrics, PVC, wallpaper, loose paint, or porous or flaking surfaces, and not suitable for wet areas. Moving the fastener after it has been stuck down will weaken the adhesive and may mark the surface. For heavier loads, rough surfaces or outdoor jobs, choose a heavy duty tape instead.Specifications Brand VELCRO® Brand Product Stick On Hook and Loop Tape Size 25mm wide x 1m long Colour Black Material Nylon hook and loop Backing Self-adhesive (peel and stick) Application Cut to length, applied by hand Full adhesive strength After about 24 hours Use Indoor only SafetyUse with normal care. Cut the tape with sharp scissors, keep small offcuts away from young children and pets, and store the roll in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$13.39
Permastik Indoor Mounting Tape is a double-sided foam tape for hanging lightweight items around the home without drills, nails or screws, supplied here as a 24mm x 5m roll. It suits everyday indoor jobs such as arts and crafts, signs and posters, and gives a neat, clean fix with no holes left in the wall.About the tapeA white, double-sided EVA foam mounting tape with a 24mm width and a thickness of about 1mm. Permastik rates it at 10kg per metre of tape, tested to Australian Standard AS 2313.0-2006. It is a medium-strength tape designed for indoor conditions only and works best at room temperature, within a range of +10°C to +40°C.Where to use itIndoors: posters, signs, craft projects, lightweight decorations and other light household items on interior walls and surfaces.Outdoors: not recommended. This tape is made for indoor use only, so choose an outdoor-rated mounting tape for exterior jobs.Suitable surfaces include painted walls, tiles, glass, metal, timber and many plastics (test plastics on a small area first).How to use itMake sure both surfaces are clean, dry and free of dust, grease and loose paint. Cut the tape to length, press it firmly onto the back of the item, peel off the liner and press the item into place on the wall for several seconds. Apply it within the recommended temperature range of +10°C to +40°C. Work out how many metres you need for the weight of the item, remembering the 10kg per metre rating.Important notesNot designed for outdoor use, damp conditions or heat-exposed locations. Use it only for light to medium items and stay well within the rated load. Results depend on the surface, so avoid dusty, crumbly, flaking or poorly bonded paint, and test on delicate or textured finishes first. Do not use it to hang items where a fall could cause injury or damage.Specifications Brand Permastik Product Indoor Mounting Tape Size 24mm x 5m roll Thickness 1mm Colour White Type Double-sided EVA foam tape Holding capacity 10kg per metre of tape (tested to AS 2313.0-2006) Temperature range +10°C to +40°C Use Indoor only Manufacturer model number 125 SafetyUse with normal care. Keep the roll out of reach of children and away from pets. Store it in a cool, dry place and keep the liner on any unused tape. Refer to the Safety Data Sheet (SDS) for full details.
$9.91
Selleys Liquid Nails VP30 Primer is a rapid-curing, water-based priming concentrate designed as a bridging primer in the Liquid Nails timber flooring system, supplied here in a 1L pack. It is used on concrete slabs and other porous or non-porous surfaces before levelling compounds or flooring adhesives go on, and it flashes off in about 30 minutes so the next stage of the job can start quickly.About the formulaA water-based hybrid polymer primer that is low in VOCs and low in odour. It changes colour as it dries, going on pink and turning red when dry, so you can see at a glance when a coat is ready. Once cured it will not re-emulsify in water, and tools and splatter can be cleaned up with water before the primer cures.Where to use itIndoors: as a bridging primer between Selleys VBS or VBS Rapid moisture barrier and self-levelling compound on concrete slabs, or to prime concrete before self-levelling compound is poured as part of a timber flooring installation.Outdoors: not intended for outdoor use. It is an interior product.Suitable for clean, sound concrete slabs and other porous or non-porous surfaces that will be topped with adhesives or floor skimming and levelling compounds. Check compatibility with your chosen flooring products before starting.How to use itStart with a clean, sound, dust-free surface and stir the primer well before use. Cut in the edges with a brush, then apply with a roller, brush or broom. Allow for roughly 6 to 10 m² per litre, depending on how porous the surface is. Leave a continuous film on the surface so the next layer bonds properly. Pour the primer out onto the floor rather than leaving it in the container, which keeps it cool and gives you more working time. Make sure the primer has dried clear and can be walked on without tackiness before pouring self-levelling compound. Good ventilation helps it cure faster. Clean up with water before the primer cures.Important notesCure time is about 30 minutes, depending on conditions. Very porous concrete or slabs with high moisture content may need a second coat. If the coating soaks away or you see dull patches or pinholes, apply another coat once the first has cured. If you are priming over a moisture barrier, make sure it is fully cured first. Do not apply over dusty or contaminated surfaces, and do not use on surfaces that are subject to standing water. Brushes and rollers are best discarded after use.Specifications Brand Selleys Product Liquid Nails VP30 Primer Size 1L Colour Pink when wet, red when dry Base Water-based Application Brush, roller or broom Cure time About 30 minutes Coverage About 6 to 10 m² per litre, depending on surface Clean up Water, before curing Use Interior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. If product gets on skin, wash with plenty of soap and water, and if it gets in eyes, rinse cautiously with water for several minutes. Keep out of reach of children and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$48.95
Selleys Liquid Nails VBS Rapid is a two-part, water-based epoxy vapour barrier kit that seals concrete slabs before timber flooring goes down, supplied here as a 1.5L resin and hardener kit. Rolled onto a dry, stable slab, it helps block moisture vapour rising from the concrete into the floor above, and its fast-curing formula suits jobs where the flooring needs to go in quickly.About the formulaA pigmented, water-based epoxy supplied as separate resin and hardener components that are mixed together just before use. The colour-coded parts blend to a uniform green, so it is easy to see when the mix is ready, and it is normally applied as a single coat. It has a low odour and can be cleaned up with water while still wet. It is designed to bond well with Selleys Liquid Nails timber flooring adhesives such as Timberflex.Where to use itIndoors: over structurally sound, dry concrete floor slabs, as a moisture vapour barrier under timber flooring that is fixed with a compatible Selleys flooring adhesive.Outdoors: not intended for outdoor use.Suitable surface: clean, dry and stable concrete slabs. Very porous concrete or slabs with high moisture content may need a second coat.How to use itComplete all your preparation and mark out the work area before you start mixing, because this product cures quickly. The slab must be clean, dry and sound, and free of curing compounds, oil, grease, wax, sealers, old coatings and adhesives. New concrete should have cured for at least 28 days or until its moisture content is below 5.5%. Mix the components thoroughly until the colour is even, with no streaks. Tip the mix onto the slab straight away rather than leaving it in the pail, then roll it on with a short-nap mohair roller and cut in the edges with a brush. If a second coat is needed, apply it after the first has cured and before 24 hours have passed. Clean tools with water before the product cures.Important notesDo not apply over damp or contaminated surfaces, or when the temperature is below 10°C or above 35°C. Cure time is rapid and the film is tack-free within hours, but allow for conditions on site such as temperature and slab porosity. Check coverage against your slab: Selleys states roughly 6 to 8 m² per litre per coat. This product is a vapour barrier system, not a flooring adhesive, so use a compatible flooring adhesive over the cured coating.Specifications Brand Selleys Product Liquid Nails VBS Rapid Vapour Barrier Pack 1.5L two-part kit (resin and hardener) Colour Green when mixed Base Two-part water-based epoxy Application Roller, with brush for edges Cure Rapid, tack-free within hours Coverage About 6 to 8 m² per litre per coat Application temperature 10°C to 35°C Clean up Water (before curing) Use Interior, over concrete slabs SafetyUse with normal care: work in a well-ventilated area, avoid contact with skin and eyes, and wear gloves and safety glasses. Keep out of reach of children and store the unused components sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$93.26
Selleys Liquid Nails Timberflex is a flexible, trowel-grade timber flooring adhesive for fixing solid, engineered strip and sheet timber floors to concrete and timber subfloors, supplied here as a single 600ml sausage pack. It is a good fit for smaller flooring jobs, patch work and trial areas where a full pail is more than you need.About the formulaTimberflex uses a silyl modified polymer (MS polymer) technology, which Selleys describes as isocyanate free and solvent free. It stays flexible once cured so the floor can move naturally. It forms clean, stable ridges under the trowel and gives good wet grab and initial hold. It spreads easily across a wide application range of 5°C to 40°C and is a low VOC product that meets Green Building Council requirements.Where to use itIndoors: engineered overlay flooring (prefinished and bamboo) and most types of solid timber, strip and sheet flooring, bonded to common subfloors such as plywood, particleboard, existing strip flooring, fibre cement sheet and concrete, including over acoustic matting.Outdoors: not recommended. This is an interior flooring adhesive and is not intended for wet areas.Suitable materials include plywood, particleboard, existing timber flooring, fibre cement sheet and steel-trowelled concrete.How to use itSurfaces must be clean, sound and level to within 3mm over 3m, because out-of-level floors increase the risk of hollow spots under strip timber. Grind concrete to remove high spots, contaminants and weak surface layers, and sand timber subfloors to remove old glue and other contaminants. Concrete should have a steel-trowel type finish. Over concrete, Selleys recommends a vapour barrier such as Liquid Nails VBS before laying to prevent moisture migration and swelling of the timber. Slab moisture content should be below 5.5% and moisture vapour transmission below 15g/m² per 24 hours. Apply the adhesive to the subfloor and spread it with a suitable Selleys Direct Stick trowel, then lay the boards into the wet adhesive. Wipe uncured adhesive from tools, hands and prefinished boards with a damp cloth before it cures.Important notesAlways follow Australian Standards, NCC requirements and best practice for timber floor installation. Allow about 24 hours for the adhesive to cure. The working time is about 45 minutes at 25°C and 50% relative humidity. Do not apply to dusty, greasy or damp surfaces. Cured adhesive is much harder to remove than wet adhesive, so clean up promptly.Specifications Brand Selleys Product Liquid Nails Timberflex Timber Flooring Adhesive Pack 1 x 600ml sausage Colour Oak Base Silyl modified polymer (MS polymer) Application Trowel applied Application temperature 5°C to 40°C Working time About 45 minutes (25°C, 50% RH) Cure time 24 hours VOC 32g/L Clean up Damp cloth before curing Use Interior timber flooring SafetyAvoid contact with eyes and prolonged or repeated skin contact, and wear gloves when working. Keep out of reach of children. Store in a cool, dry, well-ventilated place out of direct sunlight and away from foodstuffs. Refer to the Safety Data Sheet (SDS) for full details.
$19.06
The Timbermate Timber Touch Up Kit gives you a water-based wood filler and a set of wax touch-up crayons in four timber shades, so you can deal with dents, gaps and scratches around the house without sanding back a whole surface. It suits furniture, floors, door and window frames, architraves, staircases and picture frames, and it is simple enough for first-time repairers.About the formulaThe kit pairs two products. Timbermate is a water-based, interior grade wood filler made without acrylic or latex, which is why it resists shrinking, sinking, cracking and falling out of the repair. The pre-mixed colours can also be tinted with any stain or colourant to fine-tune a match. It has an indefinite shelf life, and if it dries out in the tub it can be reconstituted. Waxstix are synthetic wax crayons that contain no beeswax, so repairs accept coatings and avoid the pale ring that beeswax-based products can leave around the edges. Several sticks can be blended to match a colour or to imitate grain.Where to use itIndoors: touch-ups on timber furniture, floors, staircases, architraves, window and door frames and picture frames.Outdoors: not recommended, as this kit is intended for interior use only.Suitable for timber surfaces. The filler can be sanded, stained or painted once dry, and Waxstix repairs can be coated over.How to use itClean the damaged area and make sure it is free of dust and loose material. For gaps, holes and dents, press the woodfiller in with a scraper or putty knife, let it dry, then sand flush before staining, painting or coating. For most scratches, simply rub a Waxstix across the damage. For deeper marks, warm the stick with a flame and let the hot wax flow into the area. Scrape off any excess with a plastic scraper or a piece of cardboard. Blend more than one stick if you need a closer colour match.Important notesDrying time for the filler depends on how deep the fill is, so allow extra time for deeper repairs before sanding. Colour is easiest to judge by testing on an offcut or an out-of-sight spot first. Keep the lid on the tub when not in use to prevent it drying out. Not intended for exterior timber.Specifications Brand Timbermate Product Timber Touch Up Kit, Mixed Colours Kit contents 4 x Timbermate water-based woodfiller tubs and 4 x Waxstix touch-up crayons Colours Pine, Walnut, Hardwood (Tasmanian Oak), Mahogany Base Water-based wood filler (no acrylic or latex) and synthetic wax crayon (no beeswax) Application Filler by scraper or putty knife; Waxstix rubbed on or melted in Finishing Sandable, paintable and stainable Pack dimensions Approx. 165 x 117 x 35 mm Use Interior only SafetyUse with normal care. Work in a well-ventilated area and wear gloves if you prefer to keep your hands clean. If you heat a Waxstix, keep flammable materials away, take care with the hot wax and let it cool before handling. Keep out of reach of children and store the tubs sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$40.81
Parfix Gap Filler White is a flexible, paintable acrylic gap sealant for tidying up interior joints, supplied here as a six-pack of 450g tubes for bigger jobs or repeat use. It fills the small gaps and hairline cracks that open up around trims and frames, and it stays flexible enough to move with the surfaces either side of the joint.About the formulaA water-based acrylic paste in white. Because it remains flexible after drying, it copes with the minor movement between timber, plasterboard and other building materials better than a rigid filler. The dried finish can be painted over, so the repair blends into the surrounding wall or trim.Where to use itIndoors: gaps between skirting boards or architraves and the wall, around door and window frames, and along cracks or joints in walls and ceilings where a little movement is expected.Outdoors: not recommended. This product is sold for interior applications.Suitable for use on common interior building surfaces such as timber, plasterboard and painted walls. Check the pack label if you are unsure about a particular surface.How to use itMake sure the joint is clean, dry and free of dust, grease and loose material. Cut the nozzle to suit the width of the gap, load the tube into a caulking gun and run a steady bead into the joint. Smooth it off with a damp finger or tool for a neat finish, and wipe away excess before it dries. Once it is fully dry, the surface can be painted. Tools and uncured product clean up with water, and cured sealant needs to be cut or scraped away.Important notesDrying and curing times depend on joint depth, temperature and humidity, so allow plenty of time before painting and follow the directions on the pack. For interior use only. Replace the cap on a part-used tube so the remaining product does not dry out.Specifications Brand Parfix Product Gap Filler Pack 6 x 450g Colour White Base Water-based acrylic Finish Flexible, paintable Clean up Water (while uncured) Use Interior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses where sensible. Wash hands after use and keep out of reach of children. Store in a cool, dry place with the cap on. Refer to the Safety Data Sheet (SDS) for full details.
$24.25
Mont Marte Deco Pudge Gloss is a three-in-one craft product that works as a decoupage glue, an art sealer and a gloss varnish, supplied here in a 300ml bottle. One product lets you stick paper down, seal the surface and finish the piece with a clear, shiny coat, so you don't need to switch between products mid-project.About the formulaA non-toxic, water-based formula that dries to a clear gloss finish. It can be brushed over acrylic paint, stains, wood, fabric and decoupage work, and it can be sanded lightly between coats if you want a smoother, glossier result. Because it is water-based, brushes and hands wash up with soap and water while the product is still wet.Where to use itIndoors: decoupage on timber boxes, frames and furniture pieces, scrapbooking and paper collage, school and kids' craft projects, and sealing acrylic-painted or stained craft pieces.Outdoors: not recommended. This product is listed for indoor use only.Suitable surfaces include paper, wood and fabric, as well as acrylic-painted and stained craft surfaces. Test on an offcut or hidden area first if you are unsure about a particular material.How to use itStart with a clean, dry surface. For decoupage, brush a thin layer of Deco Pudge onto the surface under your paper, press the paper down and smooth out any air bubbles. Once the paper is in place, seal over the top with 2 to 3 thin coats, letting each coat dry before applying the next. For sealing or varnishing painted or stained work, brush on thin, even layers in the same way. A light sand between coats will give a smoother, glossier finish. Clean brushes and tools with soap and water while the product is still wet, and close the lid after use.Important notesThin coats work best. It is touch dry in about 30 minutes and fully dry in about 24 hours. For indoor craft use only. Store the bottle sealed in a cool place between 5 and 30 deg C, away from direct sunlight. This product is not intended for children to use unsupervised.Specifications Brand Mont Marte Product Deco Pudge Decoupage Glue and Sealer, Gloss Pack 1 x 300ml bottle Finish Clear gloss Base Water-based Application Brush, in thin coats Touch dry About 30 minutes Fully dry About 24 hours Recommended coats over paper 2 to 3 Clean up Soap and water while wet Storage temperature 5 to 30 deg C Bottle size 54 x 54 x 169 mm Use Indoor only SafetyKeep the lid closed when not in use, store it away from direct sunlight and out of reach of children, and wash off skin contact with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$17.46
Mont Marte Deco Pudge Matte is a 3-in-1 water-based decoupage glue, art sealer and matte varnish, supplied in a 300ml bottle for craft projects. You can stick your paper down, seal the surface and finish the piece with one product, so there is no need to swap between bottles mid-project.About the formulaA water-based, non-toxic formula with a milky appearance in the bottle. It dries clear to a soft matte finish that resists yellowing. The finish can be lightly sanded between coats for a smoother result, and brushes and tools wash out with soap and water while the product is still wet.Where to use itIndoors: decoupage, scrapbooking, school projects, paper crafts and sealing finished artwork or painted pieces.Outdoors: not recommended. This product is intended for indoor use only.Suitable for gluing paper to a surface and for sealing over acrylic paint, stains, wood, fabric and decoupage projects.How to use itBrush a thin layer of Deco Pudge onto the surface, lay your paper over it and smooth out any bubbles. Once the paper is down, brush 2 to 3 coats over the top as a sealer and varnish, letting each coat dry before applying the next. A light sand between coats leaves an extra-smooth surface. Wash tools with soap and water while the product is still wet. Reseal the bottle after use.Important notesThe product is touch dry in around 30 minutes and fully dry in about 24 hours. Store the bottle sealed in a cool place between 5 and 30 degrees C, away from direct sunlight. It is not intended for outdoor use. Always test on an offcut or a hidden spot first if you are working over a special finish.Specifications Brand Mont Marte Product Deco Pudge Decoupage Glue and Sealer, Matte Model number MMBB1210 Size 300ml bottle Appearance Milky liquid, dries clear Finish Soft matte Base Water-based Application Brush Touch dry Around 30 minutes Fully dry About 24 hours Clean up Soap and water while wet Storage temperature 5 to 30 degrees C Pack dimensions 54 x 54 x 169 mm Use Indoor only SafetyIt is a water-based craft product, but it is not designed to be eaten, so keep it away from food and drink and out of reach of young children. Children should be supervised when using it. Refer to the Safety Data Sheet (SDS) for full details.
$17.46
QEP Carpet Seaming Tape is a ready-to-use cold seaming tape for joining broadloom carpet, supplied here as a single 5 metre roll. It is made for DIY carpet installs and repairs where you want the join to stay concealed and the finished floor to look neat and professional.About the tapeThis is a step-on style tape. You don't need a heat-bond iron. You lay the tape under the seam and press the carpet edges onto it, and it holds them together. The roll is already cut to a handy length for typical DIY seams, so it is easy to handle and place.Where to use itIndoors: joining two lengths of broadloom carpet along a seam, and tidying up carpet joins during a repair or a small installation project.Outdoors: not intended for outdoor use.It is designed for carpet. Check that it suits your carpet backing before you start a larger job.How to use itMake sure the subfloor is clean, dry and free of dust and loose debris. Trim the carpet edges so they meet cleanly. Run the tape along the length of the seam and position it so the join sits centred over it. Press the carpet edges down onto the tape, then walk along the seam to firm up the contact so the edges are held together evenly. Follow any instructions printed on the pack for backing preparation and positioning.Important notesThis tape is for indoor use only. Press the carpet edges together carefully the first time, because tapes of this type grip on contact and are difficult to reposition. Keep the roll clean and stored in its packaging until you need it. Cure or set times, load ratings and traffic ratings have not been confirmed for this exact product, so check the packaging for any limits on use.Specifications Brand QEP Product Carpet Seaming Tape Pack 1 roll, 5 metres Type Cold seaming tape, applied by pressing down Application Applied by hand, no heat tools required Suitable for Broadloom carpet Use Indoor only SafetyAs a general precaution, keep the tape away from children, avoid ingesting it, store it in a cool, dry place and wash your hands after handling. Refer to the Safety Data Sheet (SDS) for full details.
$31.17
![Sika SikaBond T-55(J) Elastic Wood Flooring Adhesive 600ml Foil Pack [Ochre] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikabond-t-55-j-elastic-wood-flooring-adhesive-600ml-foil-pack-ochre-2.jpg?v=1792411222&width=645)
Sika SikaBond T-55(J) is a one-component, elastic polyurethane adhesive for fully bonding solid and engineered timber floors, supplied here as a single 600ml foil pack for smaller flooring jobs and repairs. It spreads easily, stays flexible once cured and helps take the stress out of the bond between the timber and the substrate, which suits floors that need to move a little with the seasons.About the formulaA moisture-curing polyurethane that cures by reacting with humidity in the air, so it needs reasonable ambient moisture to set properly. The cured adhesive is elastic and dampens footfall sound. It is sandable along with the floor, and Sika rates it as low in VOCs. It is approved for use over underfloor heating and can be applied directly onto old ceramic tiles, which can save you from ripping up an existing tiled floor first (do a preliminary adhesion test on glazed tiles).Where to use itIndoors: full-surface bonding of solid timber and engineered timber floors, parquetry and strip panels, mosaic and industrial parquet, and chipboard, over concrete, cement-based screeds, timber subfloors and old ceramic tiles. It can also be used as an underlay layer before timber flooring is laid.Outdoors: not intended for outdoor use, and it is not rated as UV or weather resistant.Suitable substrates include concrete, cement-based floors, chipboard, timber subfloors and ceramic tiles. Sika notes that ground-floor slabs and areas without a damp-proof membrane need moisture protection first (see important notes below).How to use itMake sure the substrate is clean, dry, sound and free of dust, contamination and old coatings or adhesives. Check the substrate moisture content before you start and prime or seal where required. Load the foil pack into a suitable application gun, snip the end and cut the nozzle tip to suit, then lay the adhesive over the floor and spread it evenly with a notched trowel. Sika's current data sheet lists coverage of roughly 600 to 1000 g per square metre depending on the trowel notch and the flooring type. Use a larger notch for long or wide boards and uneven substrates so you get a continuous bed with no hollow spots. Press the timber firmly into the adhesive while it is still wet and keep a 10 to 15mm expansion gap to the walls. Clean tools while the adhesive is uncured, using Sika Remover-208 or Sika Colma Cleaner. Cured adhesive can only be removed mechanically.Important notesSika's data sheet states this product is only suitable for use by professional wood floor applicators. Apply and lay within roughly 15 to 35 degrees ambient and substrate temperature (20 to 35 degrees with underfloor heating), with relative humidity of about 40 to 70 percent. Keep the adhesive at or above 15 degrees for good workability. The floor can be walked on after about 12 hours and sanded after about 24 hours, depending on conditions and adhesive thickness. Do not expose uncured adhesive to alcohol-containing products, as they interfere with curing. Where a ground-floor slab or other area has no damp-proof membrane, follow Sika's moisture-barrier recommendations (Sika Primer MB or MR Fast, or Sikafloor EpoCem) before laying timber. Follow the flooring manufacturer's own installation guidelines as well.Specifications Brand Sika Product SikaBond T-55(J) Elastic Wood Flooring Adhesive Pack 1 x 600ml foil pack Colour Ochre Base 1-component polyurethane, moisture curing Application Foil pack via application gun, spread with a notched trowel Skin / laying time About 60 minutes at 23 degrees and 50% RH Cure rate About 3mm per 24 hours at 23 degrees and 50% RH Walk on / sand After about 12 hours / 24 hours Coverage About 600 to 1000 g per m2, depending on trowel and flooring type Density About 1.35 kg/l Shore A hardness About 38 after 28 days Shelf life 12 months from production, unopened and stored correctly Storage Dry, out of direct sunlight, 5 to 25 degrees Use Interior only SafetyIt contains small amounts (under 1 percent) of isocyanates, so avoid skin contact and breathing vapour, and keep the product away from heat, sparks and open flames. Work in a well-ventilated area and wear gloves and eye protection. If it gets on skin, remove contaminated clothing and wash with soap and plenty of water. For eye contact, rinse with water with the eyes held open and seek advice if irritation persists. Refer to the Safety Data Sheet (SDS) for full details.
$19.37
Boyle Hot Melt Glue Sticks are a pack of eight clear 7mm sticks made for use in a high temperature glue gun, handy for home, office and school craft projects. They give a quick, strong hot glue bond on lots of everyday craft and household materials, and they suit most handicraft jobs.About the formulaThese are clear hot melt glue sticks. According to Boyle, they are non-toxic, odourless and acid free, and they dry clear so the glue line stays discreet on finished projects. Each stick is 200mm long and 7mm in diameter, so check that your glue gun takes 7mm sticks before you buy.Where to use itIndoors: craft and handicraft projects, school and homework projects, office jobs, jewellery making and quick household fixes.Outdoors: not recommended. The supplier lists this product for indoor use only.Suitable materials include cardboard, ceramics, fabric, glass, jewellery, paper, plastic, leather, metal and wood. It is a good idea to test on a small hidden spot first, especially on plastics and delicate or heat-sensitive items.How to use it Load a stick into a high temperature glue gun with a 7mm barrel and let the gun heat up fully. Make sure the surfaces are clean, dry and free of dust and grease. Squeeze the trigger to lay glue on one surface, then press the parts together straight away and hold them until the glue cools and sets. Work quickly, as hot melt glue cools fast and loses its tack. Important notesThe supplier does not list this product as child friendly, so children should only use it with close adult supervision. Molten glue and the gun nozzle get very hot and can cause burns. Do not touch hot glue with bare skin. Not recommended for outdoor use. Set and cure times and temperature resistance of the bond have not been published by the manufacturer, so test before relying on it for anything that will be heated or put under load. The sticks are sold on their own and do not include a glue gun.Specifications Brand Boyle Product Hot Melt Glue Sticks Pack 8 sticks Stick size 200mm long x 7mm diameter Colour Clear Application High temperature glue gun Use Indoor use only Features Non-toxic, odourless, acid free, dries clear SafetyMolten hot melt glue can cause serious burns, so avoid skin contact, use the glue gun on a stable heat-safe surface and unplug it when you have finished. Use in a well-ventilated area and keep out of reach of children. Store the sticks in a cool, dry place away from heat. If you get hot glue on your skin, cool the area under cold running water straight away and do not peel off the glue. Refer to the Safety Data Sheet (SDS) for full details.
$2.90
Kinetic Sink Sealing Tape is a flexible, self-adhesive foam tape for the join between a sink and the benchtop, supplied here as a handy 4 roll assorted pack. It is used underneath the sink rim to help protect the benchtop and stop leaks working their way under the bench.About the productThis is a black foam tape rather than a wet-applied sealant, so there is no cartridge, caulking gun or mess involved. The flexible foam is designed to sit in the gap under the rim of the sink. The pack includes two different profiles, so you can pick the one that suits the rim of your sink or basin: two rolls of 8mm x 8mm x 2m and two rolls of 10mm x 4mm x 2m.Where to use itIndoors: under the rim of kitchen sinks, laundry tubs and bathroom basins that sit on a benchtop, as a barrier between the sink and the bench surface.Outdoors: not intended for outdoor use. Use it for under-sink installations only.Suitable for fitting under drop-in style sink and basin rims. Check that the tape profile suits your sink rim before fitting.How to use itClean and dry the underside of the sink rim so it is free of dust, grease and old sealant. Cut the tape to length, then peel off the backing and press it firmly into place around the rim, keeping it continuous with no gaps at the corners or joins. Lower the sink into position and secure it as directed by the sink manufacturer. Always follow any instructions printed on the pack as well.Important notesChoose the profile that fits the rim of your sink best, and cut a little extra length so the run is fully covered, as small sinks can still need more than one roll. Keep the product away from heat and store it in a cool, dry place. Cure times, temperature limits and chemical resistance have not been confirmed by the manufacturer, so test in an inconspicuous spot if you have any doubts about compatibility with your sink or bench material.Specifications Brand Kinetic Product Sink Sealing Tape, assorted sizes Pack 4 rolls: 2 x (8mm x 8mm x 2m) and 2 x (10mm x 4mm x 2m) Colour Black Material Flexible adhesive foam Application Hand applied, peel and stick Use Under-sink and basin rim sealing (indoor) SafetyStore in a cool, dry place and keep out of reach of children. Wash hands after handling if the adhesive surface has been touched. Refer to the Safety Data Sheet (SDS) for full details.
$13.89
The Dulux Renovation Range Grout Pen is a ready-to-use 7ml pen that brings tired, stained grout lines back to a clean white without the mess and effort of re-grouting. It suits kitchens, bathrooms and laundries, and works well as the finishing touch after a tile makeover with the Dulux Renovation Range.About the formulaThe pen delivers a white coating that is painted directly over existing grout. It has a shaped, self-guiding tip designed to cover both narrow and wide grout lines. Dulux describes it as fast drying. The Safety Data Sheet shows a solvent-containing formula, so it needs more care than a water-based paint (see Safety below).Where to use itIndoors: grout lines on kitchen, bathroom and laundry tiles, including grout lines next to surfaces painted with Dulux Renovation Range paint.Outdoors: not intended for outdoor use.Designed for cementitious grout lines between tiles. Unpainted grout must be clean before you start: remove grease, dirt and other contamination first.How to use itMake sure the grout is clean and dry. Run the tip along the grout line with a steady hand and let the tip guide itself. If the flow of paint slows, wipe the tip with a soft cloth and press it a few times to get the paint flowing again. On vertical surfaces, work from the bottom upwards. Apply two coats, leaving at least one hour between them. Keep the pen capped and lying flat when not in use.Important notesDulux lists a touch-dry time of about 1 hour and a re-coat time of about 8 hours. The retailer specifications list a minimum application temperature of 10°C. The pen is not tintable. It is made for interior grout lines only and is not a replacement for regrouting where grout is crumbling or missing. Test on a small, inconspicuous section first if you are unsure how it will look.Specifications Brand Dulux Product Renovation Range Grout Pen Size 7ml single pen Colour White Base Solvent-containing coating (per SDS) Application Precision applicator pen Touch dry About 1 hour Re-coat time About 8 hours Tintable No Minimum application temperature 10°C Use Interior grout lines only SafetyIt is a Category 2 flammable liquid (highly flammable liquid and vapour, Hazchem code 3YE). Keep it away from heat and ignition sources, use it in a well-ventilated area, keep the pen capped when not in use, and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$28.57
Gyprock Masonry Adhesive is a dry powder adhesive made for fixing plasterboard directly to masonry and concrete walls, supplied here in a 20kg bag for full-room and trade-sized jobs. You mix it with water on site to a firm, creamy paste. It is also used to fix plaster cornice and decorative plaster castings to plasterboard walls and ceilings in residential and commercial buildings.About the formulaThis is a plaster-based, setting-type compound rather than a drying type. Once mixed, it has a working life of about 40 to 45 minutes before it starts to set. The manufacturer designs it for strong adhesion and good initial grab, and it is easy to spread by hand with a small broadknife. It is made in Australia by CSR Gyprock. The manufacturer lists a very low VOC content of 2g/L (as specified by GBCA) and notes the product is GECA accredited.Where to use itIndoors: direct-fixing plasterboard sheets to brick, block and concrete internal walls, and fixing plaster cornice and plaster castings to plasterboard walls and ceilings.Outdoors: not intended for external use. It is an internal wall lining adhesive.Suitable surfaces include brick, concrete and other masonry, plus plasterboard for cornice and casting work. Remove any paint from the areas where the adhesive will be applied.How to use itPour the powder slowly into clean domestic water and mix to a firm, creamy consistency. The manufacturer's guide is roughly 3kg of powder to 1.5 litres of water. Mix only what you can use within the working life, and never mix or re-work adhesive once it has begun to set or dry. For plasterboard, apply daubs of about 50mm diameter that stand out at least 15mm from the wall. Keep daubs no more than 450mm apart horizontally and vertically, and keep them about 50mm in from sheet ends and edges. You can apply daubs to either the wall or the back of the sheet. Position the board and hold it in place until the adhesive sets. Use levelling pads where wall irregularities exceed 15mm. Always follow the current Gyprock installation guides for full fixing details.Important notesNot suitable for use on wet area plasterboard in tiled areas. Use only clean domestic water for mixing. Keep fresh batches free from contamination and do not mix with set or drying material. The bag is non re-sealable, so plan the quantity you need. Shelf life is 12 months from the date of manufacture when the bags are stored dry, out of the weather and away from direct sunlight. Wall suitability, fixing limits and any decoration requirements should be checked against the Gyprock Red Book and technical data sheet for your job.Specifications Brand Gyprock (CSR) Product Masonry Adhesive Pack 1 x 20kg non re-sealable bag Form Dry powder (mix with water) Colour Off white Base Plaster-based setting compound Application By hand with a broadknife, applied as daubs Working life once mixed 40 to 45 minutes Coverage 20kg fixes approximately 30m2 of plasterboard Specific gravity 2.3 to 2.4 VOC content (GBCA) 2g/L Shelf life 12 months from manufacture Origin Made in Australia Use Interior SafetyAvoid eye contact and repeated or prolonged skin contact, and avoid breathing in the powder dust when opening, pouring and mixing. Wear gloves and eye protection, and use a dust mask or respirator in dusty conditions, especially when sanding or cutting set material. Wash well after handling. Store bags in a dry place, protected from weather and direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$71.12
Gyprock DIY Cornice Cement is a powder-based, mix-with-water adhesive made for fixing cornice at the wall and ceiling junction, supplied here in a handy 2.5kg bag for small rooms, repairs and touch-ups. It is a setting-type compound rather than a drying type, so it grabs well at the start and builds a high bond strength once set. It is made in Australia by CSR Gyprock.About the formulaA dry plaster-based powder that you mix with clean water into a workable paste. Once mixed, you get a working life of roughly 50 to 60 minutes, which is enough to fix several lengths of cornice and tidy the joints without rushing. Because it sets by reaction rather than by drying out, it hardens in a predictable timeframe. Gyprock describes it as a low VOC product.Where to use itIndoors: fixing Gyprock cornice at wall and ceiling junctions where the lining is plasterboard or fibre cement, finishing cornice joints and mitres, filling small gaps along the cornice line and carrying out small cornice repairs.Outdoors: not intended for exterior use. It is designed for interior cornice work.Suitable surfaces are plasterboard and fibre cement wall and ceiling linings, bonded to Gyprock cornice.How to use itCut cornice sections to length using a saw and mitre box or a mitre guide. Add 2kg of powder to 1.1 litres of clean water and mix to a creamy consistency. Only mix as much as you can use within the 50 to 60 minute working life. Apply the cement with a broadknife as a bead along both back edges of the cornice and onto the mitres. Butter and fix each length separately, starting with the shorter lengths. Hold each piece in place with temporary nails or screws, then remove the surplus cement and clean off with a brush or sponge. Smooth the mitres and fill any gaps with more cement. Leave it to set for at least 2 hours before removing the temporary fixings and sanding the joints.Important notesThe bag is not re-sealable, so plan your batches and keep the bag closed and dry between uses. Shelf life is 12 months from the date of manufacture. Do not mix more than you can use in the working time, and do not re-use material that has started to stiffen. Gyprock lists this product for residential cornice fixing and repairs on plasterboard and fibre cement. Clean tools with water before the cement sets.Specifications Brand Gyprock (CSR Gyprock) Product DIY Cornice Cement 60 Pack 2.5kg bag Colour Off white Base Plaster-based powder, setting type Application Mixed with water, applied with a broadknife Mix ratio 2kg powder to 1.1 litres of water Working time 50 to 60 minutes after mixing Set before sanding At least 2 hours Specific gravity 2.3 to 2.4 VOC content 2g/L Shelf life 12 months from manufacture Origin Made in Australia Use Interior SafetyDust created when sanding or cutting the set material is a nuisance dust, so keep dust low, work in a ventilated space and wear gloves, eye protection and a suitable dust mask when sanding. If it gets in your eyes, flush with plenty of running water, holding the eyelids open, for about 15 minutes. Store the bag in a dry place and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Gyprock Pre-Mixed Cornice Cement is a ready-to-use adhesive for fixing cornice to plasterboard or fibre cement at wall and ceiling junctions, supplied here as a 6kg re-sealable pail for home renovators. There is no mixing from powder. You stir it, apply it and fix the cornice. It also suits repairing existing cornice and cornice joints.About the formulaA water-based, drying-type compound that grips well on first contact and builds a high bond strength as it dries. It is made in Australia by CSR Gyprock as part of the Gyprock DIY range. Because it is pre-mixed, it stays workable in the pail between jobs as long as the lid is put back on. The pail is re-sealable.Where to use itIndoors: fixing cornice at wall and ceiling junctions, buttering mitres and finishing cornice joints in residential rooms, and repairing existing cornice joints.Outdoors: not intended for exterior use.Suitable substrates are plasterboard and fibre cement. It is intended for use with Gyprock cornice.How to use it1. Remove the lid and stir the compound to a smooth consistency, using clean containers and tools.2. Measure and cut the cornice lengths to size using a saw and mitre box or a mitre guide.3. Apply generous beads (about 10mm) to the back of the cornice along the top and bottom edges, and to the mitres. A stud adhesive applicator or a small broadknife works well.4. Press each section into place, then finish the joints and mitres.5. Put the lid back on straight away when you are not using it. Clean tools with water while the product is still wet.Important notesRemix before each use. Discard any product that has started to dry. Store the pail in a dry place out of direct sunlight with the lid sealed. Shelf life is 12 months from the date of manufacture. The retailer data lists this product as not easy to sand, so use it as a fixing cement rather than a sanding finish coat. Always check the cornice and substrate suit the job before starting.Specifications Brand Gyprock (CSR) Product DIY Pre-mixed Cornice Cement Pack 6kg re-sealable pail Colour Off white Base Water-based, ready-mixed drying compound Application Stud adhesive applicator or small broadknife Specific gravity 1.6 to 2.0 (water = 1) Substrates Plasterboard and fibre cement Shelf life 12 months from manufacture Origin Made in Australia Use Interior residential cornice fixing and repair SafetyFollow normal good practice for wet plaster products: avoid contact with eyes, wash skin after use and keep the pail out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$55.03
Feast Watson Glass Finish is a two-part, high-build clear epoxy that gives interior timber a thick, glossy, glass-like coating in a single pour, supplied here as the 0.5m² kit. It is designed for tabletops, benchtops, furniture and craft pieces, and it can also be used as an embedding or casting medium. Feast Watson says one application is equal to up to 40 coats of traditional varnish.About the formulaA two-part epoxy made up of a resin (Part A) and a hardener (Part B), mixed at a 5:3 ratio. It is a pour-on, self-levelling coating that is hard-wearing and scratch-resistant. The data sheet lists it as 100% solids by volume. It builds a film about 1.2mm thick and has a high gloss level. It has excellent water resistance but is for interior use only. The cured film softens and whitens above 100°C, so keep hot pots and pans off it. The kit includes the resin, the hardener, a stirrer and the Glass Finish Usage Guide.Where to use itIndoors: interior timber furniture and accessories, benchtops and tabletops, small craft and decoupage projects, and embedding or casting work.Outdoors: not suitable for exterior timber.It is made for timber, and the data sheet says it can also be used on many other interior surfaces. It can go over Feast Watson Prooftint stain. You can also tint the mix with up to 2% Prooftint for colour. Test on an offcut first, particularly on non-timber surfaces.How to use itWork in a clean, dust and lint-free room that is warm (above 20°C) and not humid (under 60%). Make sure the surface is level, dry, and free of dust, grease, wax and oil. For best results, seal the timber first with two coats of a suitable sealer such as Feast Watson Proofseal. Do not sand between coats or after sealing. Fill any knots or cracks, mask areas you do not want coated, and raise the piece off the work area so the coating can drip freely off the edges. Protect the floor underneath.Combine the resin and hardener as directed in the pack and stir thoroughly with the supplied stirrer. Do not thin the product. Pour it over the surface straight away, because mixed product left in the container heats up and sets quickly. Spread it with a brush or spreader. Do not roll or spray it. You have about 25 minutes of working time. Carbon dioxide, not heat, is what breaks up surface bubbles, so do not use a heater or hair dryer. Do not try to remove bubbles after about 30 minutes. Tidy the edges with a small brush, then leave the piece in a dust-free area to cure.Clean tools with epoxy thinners, and use it for clean-up only.Important notesNot suitable for exterior timber, vertical surfaces or flooring. Follow the mixing directions exactly. Wrong proportions, or adding extra hardener, will leave the film soft or sticky. Touch dry is 24 hours, tape can come off after 6 hours, light use is after 36 hours, and full cure takes 7 days. For large projects, consider a professional applicator and always practise on a spare board first. For deep scratches in the cured film, lightly sand and apply one more coat. For routine care, wipe with a soft damp cloth.Specifications Brand Feast Watson Product Glass Finish Epoxy Resin Kit Pack 0.5m² kit (Part A resin, Part B hardener, stirrer, usage guide) Colour Clear Sheen Gloss Base Two-part epoxy resin Mixing ratio 5:3 (resin to hardener) Application Pour and spread with brush or spreader Coats 1 Film thickness About 1.2mm Working time About 25 minutes Touch dry 24 hours Light use 36 hours Full cure 7 days Coverage About 1200ml of mixed product per 1m² (0.5m² per kit) Clean up Epoxy thinners Use Interior only SafetyUse in a well-ventilated area and keep containers closed when not in use. Wear overalls, safety glasses or chemical goggles and impervious gloves, and avoid skin and eye contact. Keep out of reach of children. Store in a cool place, and do not let the product enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$69.13
Bondall BondCrete is an Australian made bonding and sealing agent that has been a building and renovating staple since 1951, supplied here in a 1L pack. One product covers several jobs: a woodworking and craft adhesive straight from the container, a primer and sealer when diluted, and a bonding additive for cement, sand and render mixes.About the formulaA concentrated, high solids, water-based polymer product that contains a resin additive for strong bonding. It is white in the container and dries clear with no gloss. Because it is so concentrated, it can be diluted with water for most jobs, which stretches a single litre a long way. Bondall says there is seldom any need to hack, chip or acid etch most surfaces before bonding.Where to use itIndoors: tile bedding and fixing, bonding render or toppings to prepared surfaces, sealing and dustproofing concrete floors in covered areas, priming porous walls before water-based paint, and woodworking and general craft projects.Outdoors: Bondall directs that exterior sealing needs its separate paving and concrete sealer, and BondCrete is not intended to be exposed to water, moisture or dampness. Treat this product as an interior or covered-area product.Suitable materials include concrete, brick and other masonry, plaster, stone, tiles and timber, along with other porous surfaces.How to use itStart with a surface free of dirt, dust, oil, grease and loose or flaking material. Stir well before use. Dilution ratios from the manufacturer (BondCrete to water): Sealer coat: 1 part BondCrete to 4 parts water Bondcoat for bedding, render or topping: 1 part to 1 part water. Apply the bedding while the coat is still wet or tacky. Admix for cement, sand and render: 1 part BondCrete to 10 parts water, used in place of mixing water. As a guide, 1L makes enough admix for about 20kg of cement. Woodworking adhesive: use neat, applied to one surface only. Press the pieces together and clamp lightly. Allow a sealer coat to dry for about 24 hours before painting with a water-based or acrylic paint.Important notesUsed neat, it sets in about 30 minutes and reaches maximum strength after 24 hours. Cement mixes made with BondCrete still follow normal curing, with full cure at around 4 weeks. It is not suitable for bonding plastic, rubber, glass or other non-porous materials. It is not suitable for permanently wet areas. Do not seal a floor with it if you plan to use an oil-based paving paint or similar floor coating. Drying times vary with the application and temperature, so allow at least 24 hours between coats. Protect it from freezing and from extremes of temperature and direct sunlight.Specifications Brand Bondall Product BondCrete Bonding & Sealing Agent (Cement Additive) Pack 1L Colour White in the container, dries clear Base Water-based vinyl acetate polymer mix Application Neat from the container, diluted as a sealer or bondcoat, or mixed into cement as an admix Set time (neat) About 30 minutes Maximum strength (neat) About 24 hours Coverage (older manufacturer datasheet) About 3.5 m² per litre undiluted, up to about 35 m² per litre at 1:4 dilution Use Interior and covered areas Origin Made in Australia SafetySwallowing it may irritate the stomach and cause nausea and vomiting. Vapours or mists may irritate the nose, throat and airways. Skin contact may cause redness or itching. Use with good ventilation, and wear gloves and eye protection as a sensible precaution. Refer to the Safety Data Sheet (SDS) for full details.
$31.98
![Roberts Quick-Repair Floor Putty 88ml [Brown] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-brown-2.png?v=1792410967&width=645)
Roberts Quick-Repair Floor Putty in Brown is a ready-to-use acrylic filler for hiding gaps, nicks, scratches and fastener holes in laminate, hybrid, vinyl and engineered timber floors. It comes in an 88ml squeeze tube, so it suits small touch-ups during an install or repairs to a floor that is already down. The brown shade can be used on its own or mixed with other Roberts Palette putty colours to match your floor.About the formulaThis is a water-based acrylic putty with a thick paste consistency. It is ready to use straight from the tube and is made to dry quickly without shrinking back out of the repair. Once dry it can be sanded or painted. The manufacturer also describes it as low VOC and gives it a two-year shelf life.Where to use itIndoors: filling nail and screw holes during floor installation, patching chips and scratches on existing laminate, vinyl or engineered timber floors, and closing small gaps at board edges.Outdoors: not intended for outdoor use. It is listed for interior flooring repairs only.Suitable materials include laminate, hybrid and vinyl flooring (including LVP and LVT), engineered timber and wood flooring. Test the colour in a small, hidden spot first, because the shade shifts a little as the putty dries.How to use itClean the damaged spot and make sure it is dry and free of dust. Knead the tube for at least 20 seconds to mix the putty. Squeeze a little onto the damage and work it into the nick, scratch or hole with a putty knife. Wipe the excess off the surrounding floor with a damp rag before it dries. If the colour is not quite right, blend two shades together before applying. Once dry, sand lightly if needed. The putty can be painted over for further colour options. Wash tools and hands with soap and water.Important notesAlways use the lightest base colour of your floor as the starting point for colour matching, and let a test patch dry completely before judging the match. The manufacturer lists a dry time of about 30 minutes, but this depends on temperature, humidity and how thick the fill is. For best results, store the tube at room temperature and do not let it freeze, as freezing may affect performance. This putty is made for flooring repairs and is not a structural filler or an adhesive.Specifications Brand Roberts Product Quick-Repair Floor Putty (Palette range) Model number PC7725 Size 88ml tube Colour Brown Base Acrylic Application Squeeze tube, applied by hand or with a putty knife Dry time About 30 minutes (manufacturer listing) Finish Matte once cured; can be sanded, painted or stained Clean up Soap and water Shelf life 2 years Use Interior flooring SafetyWear gloves and eye protection when working, and make sure the area is ventilated. If it gets on skin, wash straight away with soap and plenty of water. Keep out of reach of children and keep the lid closed when not in use. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
![Roberts Quick-Repair Floor Putty 88ml [Dark Brown] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-floor-putty-88ml-dark-brown-2.png?v=1792410954&width=645)
Roberts Quick-Repair Floor Putty in Dark Brown is a ready-to-use acrylic filler for hiding gaps, nicks and scratches in modern click-together and plank flooring, supplied in a handy 88ml squeeze tube. It suits quick touch-ups on existing floors as well as tidying up nail and screw holes during installation, and the dark brown shade can be used on its own or blended with other Roberts colours to get closer to your floor.About the formulaAn acrylic-based putty that is formulated to dry quickly without shrinking. Once dry it can be sanded or painted, so you can refine the repair after it sets. It is a low VOC formula, and it is supplied in a soft tube so you can apply it straight from the pack with no mixing. Roberts quotes a two-year shelf life.Where to use itIndoors: filling small scratches, chips, dents and open joints on laminate, hybrid, vinyl and engineered timber floors; concealing nail and screw holes while a floor is being installed; touching up localised damage on floors that are already in place.Outdoors: not intended for exterior use.Suitable surfaces include laminate, hybrid flooring, vinyl flooring and engineered timber flooring. Choose, or mix, a shade that matches the lightest base colour of the floor for the most natural result.How to use itMake sure the area is clean, dry and free of dust and loose debris. Knead the tube thoroughly for at least 20 seconds before use. Squeeze the putty into the gap, nick or hole and work it in with a putty knife or similar tool so it sits flush with the surface. Wipe excess off the surrounding floor with a damp rag before it dries, because dried residue on the floor surface is harder to remove. When the putty has dried it can be lightly sanded or painted if needed. Test the colour on an offcut or an inconspicuous spot first.Important notesThis is a cosmetic filler for small damage, not a structural repair product. Deep chips or large missing areas may need a different repair method. The putty is not rated as water resistant, so it is not recommended for wet areas or continual moisture. Store at room temperature and do not let the tube freeze, as freezing may affect performance. Reseal the tube after use. Colour on screen may vary slightly from the real product, so check the shade before committing to a full repair.Specifications Brand Roberts Product Quick-Repair Floor Putty Size 88ml tube Colour Dark Brown Base Acrylic Application Squeeze tube, applied by hand Finish options Can be sanded or painted once dry Suitable floors Laminate, hybrid, vinyl and engineered timber Shelf life 2 years VOC Low VOC Use Interior floors SafetyIt is marketed as low VOC and safe to use, but normal care still applies: avoid contact with eyes, keep out of reach of children, and wash hands after use. Do not swallow. Store the tube at room temperature and protect it from freezing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
Plaid Mod Podge Gloss is a classic all-in-one craft product that works as a glue, a sealer and a finish, supplied here in a 236ml (8 fl oz) bottle. It is a water-based formula that dries clear to a smooth, glossy surface, making it a go-to for decoupage, scrapbooking, kids' crafts and general paper, wood and fabric projects.About the formulaA non-toxic, water-based acrylic sealer, glue and finish that is certified AP non-toxic and cleans up with soap and water while still wet. It dries quickly, so you can build up several thin coats for a deeper gloss, and it can be lightly sanded between coats for a smooth, glassy result.Where to use itIndoors: decoupage with paper or tissue, scrapbooking and card making, sealing painted or printed craft pieces, finishing wooden craft items, and bonding or topcoating fabric in craft projects.Outdoors: this standard gloss formula is aimed at indoor craft use. The Mod Podge range has a separate outdoor formula for items that will be exposed to weather.Suitable materials include paper, cardboard-style craft papers, wood, canvas and fabric, and it works best on porous surfaces. Plastic can be used but may need light sanding or preparation first for good adhesion, so test a small area before starting.How to use itMake sure the surface is clean, dry and free of dust and grease. Apply a thin, even coat with a brush or sponge applicator, press down your paper or fabric and smooth out any bubbles or wrinkles. Once it is dry, brush a thin coat over the top as a sealer. Allow each coat to dry completely before adding the next, and lightly sand between coats with fine sandpaper if you want an extra-smooth finish. Clean tools and skin with soap and water while the product is still wet. Close the bottle firmly after use.Important notesSeveral thin coats give better results than one thick coat. Dried Mod Podge is not water-resistant, so it is not the right choice for items that will be left outdoors or regularly soaked. If you need a finish that stands up to dishwashing or the weather, choose the matching Mod Podge dishwasher-safe or outdoor formula instead. Always test on an offcut or hidden area first, especially on plastics, delicate papers and printed images.Specifications Brand Plaid (Mod Podge) Product Mod Podge Gloss Sealer, Glue and Finish Size 236ml (8 fl oz) bottle Finish Gloss, dries clear Base Water-based acrylic Application Brush or sponge applicator Sandable Yes Clean up Soap and water while wet Use Interior craft use SafetyIt is not intended to be eaten. Keep out of reach of young children, wash hands after use, and rinse eyes with plenty of water if they are splashed. Store the closed bottle at room temperature. Refer to the Safety Data Sheet (SDS) for full details.
$22.03
![Roberts Quick-Repair Putty 88ml [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/roberts-quick-repair-putty-88ml-grey-2.png?v=1792410905&width=645)
Roberts Quick-Repair Putty in Grey is a ready-to-use floor repair filler for hiding gaps, nicks, scratches and fastener holes in laminate, vinyl, hybrid and engineered or timber floors, supplied in a handy 88ml squeeze tube. It suits both fresh installations and repairs to floors that are already down, and it can be used straight from the tube or blended with other Roberts shades to match your flooring.About the formulaAn acrylic-based putty that dries quickly and is made not to shrink back as it dries. It sands smoothly and can be painted over, so you can fine-tune the colour or finish once it has set. It is a low VOC product with a two-year shelf life, and the soft tube lets you squeeze out a controlled bead for neat, quick application.Where to use itIndoors: filling nail and screw holes during floor installation, closing small gaps between boards or planks, and touching up chips, dents and scratches on existing laminate, vinyl, hybrid and timber floors.Outdoors: not intended for outdoor use.Suitable surfaces include laminate flooring, vinyl flooring, hybrid flooring, engineered timber and solid timber floors. Grey is a mixable base shade, so test your colour match on an offcut or a hidden spot before committing to a visible repair.How to use itClean the area first so it is free of dirt, dust and grease. Knead the tube well for about 20 seconds, then snip the tip to suit the size of bead you need. Press the putty firmly into the gap or hole and smooth it level with the floor. Wipe any excess off the surrounding floor with a damp rag before it dries, because dried-on filler is much harder to remove. If you need a closer colour match, mix shades before applying. Once the putty has fully cured it can be sanded flush or painted if required.Important notesAlways choose or blend a shade that matches the lightest base colour of your floor. Store at room temperature and do not let the tube freeze, as freezing can affect performance. Cure and recoat times vary with bead depth, temperature and humidity, so allow the repair to cure fully before sanding, painting or walking on it heavily. Reseal the tube after use to keep the remaining putty usable.Specifications Brand Roberts Product Quick-Repair Putty (Model PC7728) Size 88ml tube (3 oz) Colour Grey Base Acrylic Application Squeeze tube, hand applied Finish Sandable and paintable VOC Low VOC Shelf life 2 years Use Interior flooring repairs SafetyIf it gets in your eyes, rinse with plenty of water. Keep out of reach of children and store the tube sealed at room temperature, away from freezing. Refer to the Safety Data Sheet (SDS) for full details.
$17.29
Permastik Mirror Mounting Tape is a double-sided foam tape made for hanging mirrors and other lightweight flat objects indoors without drills, nails, screws or messy glue, supplied here as a single 32mm x 5m roll. It suits renovators and DIYers who want a clean, quick fix that leaves no visible fixings, and it is a popular choice for frameless bathroom, bedroom and hallway mirrors.About the tapeThis is a heavy duty, double-sided foam mounting tape in white, with a pressure-sensitive adhesive on both faces. There is nothing to mix, no cure time to wait out and no tools needed. Permastik rates its mounting tapes by the load each metre of tape can carry, and tests them to Australian Standard AS 2313.0-2006. The tape is designed for use across a wide temperature range, from -20°C up to +60°C. Check the pack for the exact load rating of this roll before you plan your job.Where to use itIndoors: mounting mirrors, wall-mounted panels, signs, plaques and other flat, lightweight household items to clean, dry, smooth surfaces.Outdoors: not recommended. This is an indoor tape. For outdoor jobs choose a purpose-made outdoor mounting tape.Suitable surfaces include painted walls, glass, tiles, metal and timber, provided they are clean, dry, smooth and flat. Porous or uneven surfaces such as plaster, raw concrete, bare wood and fabrics need to be primed, filled or sealed first. Bare metal should be primed or abraded, and low-energy surfaces such as non-stick paints and some polypropylene plastics need treatment before they will hold. Test a small area first if you are unsure.How to use it Clean the wall and the back of the item so they are free of dust, grease and loose paint, then let them dry completely. Apply the tape vertically. Do not apply it horizontally. Cut lengths to suit the job and stick them to the back of the object, keeping them evenly spaced. Check your position carefully, because the bond grabs quickly and repositioning is difficult. A removable pencil line or a helper makes alignment easier. Press the object onto the surface with firm, even pressure for 30 seconds. Support the object until the bond has fully developed. In cold conditions (below 10°C), warm the surface gently with a hair dryer and apply the tape while the surface is still above 10°C. Important notesMounting tape is intended to be a permanent fixing, and removing it may damage the surface. If you do need to take the item down, the manufacturer suggests running dental floss behind it to cut through the foam. Do not use on uneven surfaces, and keep the mounted object to no more than 30mm thick. Do not exceed the load rating on the pack. Heavy or valuable items should be fixed mechanically or with a structural adhesive instead.Specifications Brand Permastik Product Mirror Mounting Tape Pack 1 roll, 32mm x 5m Thickness 3mm Colour White Type Double-sided foam mounting tape Application Hand applied, no tools required Service temperature -20°C to +60°C Testing standard AS 2313.0-2006 Use Indoor SafetyIt is a solid tape with no solvents to handle, but keep it out of reach of children. Cut with scissors or a sharp blade and take care with the cutting edge. Store the roll in a cool, dry place with the liner in place so the adhesive stays clean. Refer to the Safety Data Sheet (SDS) for full details.
$17.96
3M Heavy Duty Black Duct Tape is a dependable all-rounder for the toolbox, supplied here as a single 48mm x 41.1m roll for sealing, holding, bundling and quick repairs around the home, workshop or jobsite. It combines a grabby rubber adhesive with a tough, water-resistant cloth-reinforced backing, so it sticks quickly, tears cleanly by hand and leaves a neat black finish.About the formulaThis is a cloth-reinforced duct tape with a polyethylene backing over a woven scrim and a natural rubber adhesive system. 3M describes the adhesive as an improved, industrial strength formulation that bonds on contact, so you can seal, hold or reinforce straight away without waiting. The backing is flexible and conformable, applies smoothly and resists moisture for longer-lasting repairs. The tape is a medium-strength, temporary solution, not a structural bond.Where to use itIndoors: sealing and holding boxes and packages, bundling cables and hoses, re-gripping tool handles, patching and reinforcing items, labelling and colour-coding, and general fix-it jobs around the house, office or workshop.Outdoors: this tape is intended for indoor use only, so choose a purpose-made weatherproof or UV-stable tape for exposed outdoor repairs.Suitable surfaces include metal, glass, plastic, cardboard and corrugate, and laminate. Test on a small, hidden area first if you are unsure, particularly on painted, delicate or textured surfaces.How to use itClean the surface so it is dry and free of dust, oil, grease and loose material. Pull off the length you need and tear it by hand, either lengthwise or crosswise, with no scissors required. Press the tape down firmly along its whole length, smoothing out wrinkles and air bubbles so the adhesive makes full contact. Overlap adjacent strips slightly when you are sealing or reinforcing a larger area.Important notesThis is a temporary, medium-strength solution and is not designed for load-bearing or structural fixing. It is intended for indoor use only. Adhesion will be reduced on dusty, wet, oily or very rough surfaces. Rubber-based tapes can leave residue on some surfaces, so test before applying to finished or delicate materials, and remove the tape sooner rather than later where a clean removal matters.Specifications Brand 3M Product Heavy Duty Black Duct Tape Model 2145-BK Size 48mm x 41.1m Pack 1 roll Colour Black Adhesive Natural rubber Backing Polyethylene over cloth scrim Tear By hand, lengthwise or crosswise Use Indoor SafetyKeep away from heat and open flame, as the backing and adhesive are combustible. Handle with care when tearing and avoid contact with eyes. Store rolls in a cool, dry place out of direct sunlight and away from extreme heat to protect the adhesive. Always follow the manufacturer's instructions and refer to any manufacturer safety information supplied with the product. Refer to the Safety Data Sheet (SDS) for full details.
$24.89
Bostik Ultraset SF Pro is a ready-to-use, solvent-free polyurethane adhesive for fixing timber flooring, supplied here as a single 600ml sausage pack. It is an elastomeric, one-part formula made for fitting parquet, solid strip, engineered, bamboo and sheet timber flooring to flat concrete or timber subfloors, or over an existing floor.About the formulaA one-part, moisture-curing polyurethane with no solvent and a zero VOC rating. There is no mixing, and it spreads easily. It stays flexible after full cure, so the bond can move with the timber, and it is suitable over radiant heating. Bostik also lists good acoustic properties, and the product is made in Australia. The technical data sheet notes testing to ASTM C794 for peel adhesion on a range of Australian hardwoods. It also notes that the product meets EN 14293:2006 for adhesives bonding parquet to a subfloor. Bostik quotes a Shore A hardness of about 52 and a timber-to-timber shear strength of 1.4 N/mm2 (2mm bond line, BS EN 14293).Where to use itIndoors: direct-stick installation of timber floors over flat concrete or timber subfloors, or over existing floors, in residential and commercial settings. It can also fix recommended acoustic underlays as an intermediate layer between the subfloor and the flooring.Outdoors: not intended for exterior use.Suitable flooring types include parquet, solid strip, engineered, bamboo and sheet timber systems.How to use itSurfaces must be clean, dry, sound and free of voids, curing compounds, loose material, oil and grease. The subfloor should be flat to within 3mm over a 3m straightedge. If it is out of tolerance, prime and level it first using Bostik's recommended primer and levelling compound, and follow their data sheets. Spread the adhesive evenly so the film is not patchy and has no pinholes. The data sheet calls for a wet film thickness above 300 microns. Lay the flooring in line with the timber manufacturer's installation instructions. Where a vapour barrier is needed over a new or green slab, Bostik's Ultraseal Vapour Barrier is the recommended option.Important notesThe adhesive needs atmospheric moisture to cure. In low humidity (below 40%), check with Bostik technical services before you start. Do not use it as a waterproofing membrane. Do not install it over wet, contaminated or friable surfaces, and keep it away from water exposure. Allow timber to acclimatise and leave expansion gaps as the timber manufacturer or installation standard requires. Dense, burnished concrete may need abrading first. Cure and walk-on times depend on temperature, humidity and film thickness, so check the current data sheet for your job. A sausage gun is needed to dispense the 600ml foil pack, and it is not included.Specifications Brand Bostik Product Ultraset SF Pro Solvent Free Polyurethane Timber Flooring Adhesive Pack 1 x 600ml sausage Base One-part, solvent-free, moisture-curing polyurethane (elastomeric) VOC Zero VOC Application Sausage gun, spread with a notched trowel Shore A hardness Approx. 52 Shear strength (timber to timber, 2mm) 1.4 N/mm2 (BS EN 14293) Standards Tested to ASTM C794; meets EN 14293:2006 Use Interior timber flooring, including over radiant heating Origin Made in Australia SafetyBostik describes it as solvent-free and non-flammable. Wear chemical-resistant gloves and eye protection, work with good ventilation, and avoid skin contact and breathing vapour. Store in the original sealed container, under cover, dry and within the manufacturer's temperature range. Refer to the Safety Data Sheet (SDS) for full details.
$15.67
![Selleys No More Gaps Timber Floors Gap Filler 380g [Baltic] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-no-more-gaps-timber-floors-gap-filler-380g-baltic-2.jpg?v=1792410739&width=645)
Selleys No More Gaps Timber Floors in Baltic is a flexible, wood-fibre gap filler made for sealing the gaps between tongue and groove floorboards, supplied as a single 380g cartridge. The Baltic tint is made to sit in lighter timber floors, so the repair blends in once it has been sanded and finished.About the formulaA water-based acrylic filler loaded with real wood fibre. The fibre helps the cured filler take stain better than a standard gap filler, and it sands back to a smooth, clean surface. It stays flexible to cope with the seasonal movement of floorboards and forms an airtight seal that helps keep out draughts, dust and pests. Baltic is tinted to suit pine, myrtle and alpine ash. Hardwood, Jarrah and Walnut tints are available separately for other timbers.Where to use itIndoors: gaps around and between tongue and groove timber flooring, and between timber panels and fittings such as skirting boards, architraves and benchtops.Outdoors: not suitable. This is an interior-only product.Suitable materials include timber flooring, timber panels and fittings, and engineered timber floors. The Baltic tint is the best match for pine, myrtle and alpine ash.How to use itMake sure the gap is clean, dry and free of dust. Cut the cartridge seal and nozzle to suit the width of the gap, fit the nozzle and load the cartridge into a caulking gun. Force the filler well into the gap, then press it in and smooth it off with a spatula, taking care not to drag filler back out of the joint. Scrape surplus filler off the timber surface with the spatula to cut down on sanding later, and wipe up any smears straight away with a damp cloth. Allow the filler to cure fully before sanding, staining, varnishing or painting. Wear a P1 dust mask when sanding.Important notesNot for exterior use. Not for gaps wider than 3mm in trafficable joints. Allow at least 24 hours to cure, and longer in cold or damp conditions. Uncured filler cleans up with water, while cured filler needs to be sanded or scraped off. Keep the cartridge stored above 5°C. Test stains and finishes on a small area first, as the final colour depends on the timber and the finish used.Specifications Brand Selleys Product No More Gaps Timber Floors Gap Filler Pack 1 x 380g cartridge Colour Baltic (suits pine, myrtle, alpine ash) Base Water-based acrylic with real wood fibre Application Cartridge, via caulking gun Full cure 24 hours Coverage About 18 m of 3mm bead per cartridge Sandable Yes Stainable Yes Paintable Yes Clean up Water (while uncured) Use Interior only SafetyAvoid prolonged skin contact and keep the product out of the eyes, and wash your hands after use. Wear a P1 dust mask when sanding the cured filler. Keep out of reach of children and avoid letting the product enter waterways. Store above 5°C. Refer to the Safety Data Sheet (SDS) for full details.
$21.33
Selleys Plastic Wood is a fast-setting, solvent-based wood filling cement for repairing holes, dents and chips in interior timber, supplied here in a 230g maple-coloured tin. It is a simple fix for furniture, skirting, architraves and other indoor joinery, and once set it can be worked much like the timber around it.About the formulaA solvent-based paste containing natural wood fibres, finished in a maple (tan) colour. It dries quickly to a hard finish that holds up to sanding, nailing and planing. Once dry it can be stained, varnished, painted or lacquered, so the repair can be finished in the same way as the surrounding wood. It is a rigid filler, so it is not designed for joints that move.Where to use itIndoors: filling nail holes, dents, chips and small cracks in furniture, doors, window frames, skirting boards, architraves and other interior woodwork.Outdoors: not recommended. The manufacturer rates this product for interior use only.Suitable materials include natural timber and wood veneer.How to use itStir the product thoroughly before use. Make sure the surface is clean, dry and free of loose material. Press the filler in with a putty knife and slightly overfill deeper holes so there is room to sand back flush. Do not fill deeper than 6mm in a single application. Let it dry fully before sanding, staining, painting or lacquering. Wipe the putty knife clean with methylated spirits. Press the lid on firmly after use and store the tin somewhere cool.Important notesNot suitable for exterior use. Not recommended where structural movement may occur, so use a flexible product for joints and gaps between surfaces. Work in a well-ventilated area. Colour is maple only, so test a small area first if you need to match a different timber tone, or plan to stain or paint over the repair.Specifications Brand Selleys Product Plastic Wood Filler Cement Size 230g tin Colour Maple Base Solvent-based, with natural wood fibres Application Putty knife Maximum fill depth 6mm per application Set speed Fast setting Clean up Methylated spirits Use Interior only SafetyThis is a highly flammable solvent-based product. Keep it away from heat, sparks, flames and other ignition sources, and avoid static discharge. It can irritate skin and eyes, and the vapours may cause drowsiness or dizziness. Use only in a well-ventilated area and avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.
$38.42
Elmer's Glue-All Multi-Purpose Extra Strong Liquid Glue is a general-purpose white PVA glue for craft tables, classrooms and light household repairs, supplied in a 473ml bottle. It joins porous and semi-porous materials such as paper, fabric, wood, leather and ceramics, and its easy, ready-to-use formula suits beginners and families.About the formulaA water-based, white PVA (polyvinyl acetate) liquid glue with a mild vinegar-like odour. The manufacturer describes it as non-toxic, with a strong bond and a quick-drying, clear-drying finish. It needs no mixing, and it can also be used to make homemade glue slime.Where to use itIndoors: school and craft projects, paper and cardboard work, fabric and leather crafts, small timber and ceramic repairs, and odd jobs around the kitchen, workshop, den or garage.Outdoors: not recommended. The product is intended for indoor use only.Suitable materials include paper, cardboard, fabric, wood, leather and ceramics.How to use itMake sure the surfaces are clean, dry and free of dust, oil and grease. Apply a thin, even layer of glue to one or both surfaces, press the parts together and hold or clamp them until the glue grips. Wipe away any excess straight away with a damp cloth, as wet glue washes up with soap and water. Leave the bond to fully dry before putting it under load. Close the cap firmly after use.Important notesDo not use on photos, bare metal, or surfaces that will be submerged or heated. Keep the product from freezing, because freezing can damage the glue. This is not a structural adhesive, so choose a purpose-made product for load-bearing or outdoor jobs. Always test a small hidden area first on delicate or finished surfaces.Specifications Brand Elmer's Product Glue-All Multi-Purpose Extra Strong Liquid Glue Size 473ml bottle Colour White liquid Base PVA (polyvinyl acetate), water-based Application Bottle, applied by hand Clean up Soap and water while wet Use Indoor use SafetyNormal use does not call for special protective equipment, but wash your hands after use and keep the bottle out of reach of young children. In case of eye contact, rinse well with water. Store in the original container with the cap closed, away from freezing conditions. Refer to the Safety Data Sheet (SDS) for full details.
$12.07
Gorilla Super Glue Gel is a thick, no-run cyanoacrylate adhesive for quick household repairs, supplied here as a 20g bottle. The gel body gives you much more control than a thin liquid super glue, so it suits vertical surfaces, uneven parts and small jobs where you do not want drips. It sets fast with no clamping and dries clear.About the formulaAn ethyl cyanoacrylate gel that sets in about 10 to 45 seconds depending on the amount of glue and the surface. It is formulated to cope with knocks, drops and shocks, so repaired items stand up to everyday handling better than with a brittle super glue. The bottle has an anti-clog cap with a metal pin that helps keep air out, so the glue stays usable between jobs. The gel can separate over time, so shake the capped bottle before use.Where to use itIndoors: household and craft repairs on ceramics, trims, handles, toys, shoes and leather goods, small furniture fixes, and other jobs where a quick, clear bond is wanted.Outdoors: the manufacturer recommends Gorilla Super Glue primarily for indoor use, so treat this product as an indoor repair glue.Suitable materials include most plastics, metal, wood, ceramic, stone, rubber, leather, paper and fabric. Not recommended for polyethylene, polypropylene or similar low-energy plastics. Test a small hidden area first on delicate or finished surfaces.How to use itProtect your work area from spills. Make sure the surfaces are clean and dry. With the cap on, shake the bottle, then turn it upside down and tap it on a hard surface to move the gel into the nozzle. Remove the cap and apply a small amount to one surface only. Use about one drop per 6.5 cm2, because too much glue can delay the bond or cause it to fail. Press the parts together for about 10 to 45 seconds. Gaps and uneven surfaces can slow the bond. Allow 24 hours for a full cure. After use, wipe the nozzle with a dry cloth, refit the cap and keep the bottle in a cool, dry place away from moisture.Important notesNot for use on polyethylene or polypropylene plastics. Cyanoacrylate bonds skin in seconds, so never pull bonded skin apart. Soak the area in warm soapy water and gently work it free, or use acetone according to the solvent maker's directions. Acetone can mar surfaces and discolour fabric. The glue reacts with water and alkaline materials, generating heat, so keep it away from moisture. It is not intended for food contact and should not be stored in the fridge.Specifications Brand Gorilla Glue Product Super Glue Gel Size 20g bottle Colour Clear Chemistry Ethyl cyanoacrylate gel Application Squeeze bottle with anti-clog cap, hand applied Set time About 10 to 45 seconds Full cure 24 hours Service temperature (cured) About -53°C to 104°C Use Primarily indoor SafetyHazard classification: combustible liquid, causes skin irritation, causes serious eye irritation, may cause respiratory irritation. Bonds skin and eyes in seconds. Keep out of reach of children. Use in a well-ventilated area, avoid breathing vapours, and keep away from heat, sparks and open flames. Refer to the Safety Data Sheet (SDS) for full details.
$17.47
Bostik Glu Stik is the classic clear-drying glue stick that generations of Australian classrooms, craft rooms and home offices have run on. This listing is a bulk pack of ten 35g sticks, which is the economical way to buy for a school term, a busy studio, an office stationery cupboard or a community group that goes through glue faster than anyone expects.The formula is a solid, solvent free adhesive that glides on smoothly and dries clear, so finished work looks clean rather than patchy. It is acid free, which matters when you are mounting photographs or building a scrapbook that needs to survive a few decades without yellowing or corroding the materials underneath. The non-wrinkle characteristic means lightweight paper stays flat instead of buckling as the glue dries. The twist-up applicator keeps hands clean and lets you control how much stick is exposed at a time.Where to use itIndoors Scrapbooking, journaling and album building Cut and paste activities, school projects and classroom worksheets Paper craft, card making, collage and invitations Dry mounting photographs and artwork General office and stationery work on paper and light card OutdoorsNot recommended. This is a water soluble stationery adhesive with no weather or moisture resistance, so anything destined for outdoor exposure needs a different product.What it bondsPorous materials, including paper, cardboard, photographs, cellophane, crepe and tissue paper, foil and fabric. Surfaces need to be clean and dry for a reliable bond.How to use Check that both surfaces are clean and dry. Remove the cap and turn the base clockwise until a small amount of glue protrudes. Expose only what you need. Apply with firm, even strokes to one surface. Press the two surfaces together. Initial grab is roughly 20 to 40 seconds. Turn the base anti-clockwise to retract the glue and recap straight away so the stick does not dry out. Tip: if a stick has been left uncapped and has dried out, sitting it in warm water for a few minutes will usually bring it back rather than sending it to the bin.Important notes Designed for lightweight bonding. It is not suitable for heavy duty repairs or structural work. Not suitable for non-porous surfaces such as metal, glass or most plastics. No water resistance. Bonded work should be kept dry. Always recap after use. An uncapped stick will dry out. Store between 5°C and 30°C, out of direct sunlight. The formula contains corn starch. It is free from wheat, gluten, flour, egg and nut ingredients, though repeated or prolonged contact may cause an allergic reaction in susceptible people. Specifications Brand Bostik Product Glu Stik Pack 10 x 35g sticks Type Solid stick stationery adhesive Colour White stick, dries clear Solvent content Solvent free Acid free Yes Initial grab Approximately 20 to 40 seconds Clean up Warm soapy water Suitable surfaces Paper, cardboard, photographs, fabric Storage 5°C to 30°C, away from direct sunlight Compliance Tested to AS/NZS ISO 8124.3 (Safety of Toys, migration of certain elements) SafetyIt is non-toxic and solvent free, which is why it is cleared for classroom use, but it is still an adhesive and not a toy. Keep it out of reach of very young children, avoid eye contact, and do not eat it. Wash residue off skin and surfaces with warm soapy water. Refer to the Safety Data Sheet (SDS) for full details.
$43.00
The Hotwire Floor Heating Mat delivers all the comfort of Hotwire under tile heating with the heating cable already pre-spaced on a self-adhesive fibreglass mesh. Instead of fixing a loose cable, you simply roll the mat out across the floor — installation is fast, spacing is guaranteed even, and the finished system is invisible, silent, dust-free and energy efficient. At just 3.6 mm thick, the mat adds almost no height to the floor build-up, and the single cold tail keeps wiring simple. Every mat is supplied as a complete system with a fully programmable touch screen thermostat, floor temperature probe, installation alarm, tape and manual; WiFi and dual thermostats are available as upgrades.Where to use itPerfect for bathrooms, ensuites, laundries, kitchens and living areas under tile or stone. The ultra-thin profile makes it equally suited to new builds and retrofits in existing homes where floor height is limited, and the gentle radiant heat also dries wet-area floors, helping keep mould at bay.How to useMeasure the free floor area, roll the mat out and press the adhesive mesh onto a clean, primed subfloor, cutting the mesh (never the cable) to turn at walls. Fit the floor probe, then tile directly over the mat. All wiring, thermostat connection and testing must be completed by a licensed electrician, with resistance readings recorded before, during and after tiling.Important notesSize the mat to the open floor area only, excluding vanities, baths and fixed cabinetry. The heating cable must not be cut or shortened. Register your warranty after installation; the heating element is covered by a lifetime warranty (conditions apply).Specifications Wattage Coverage 300 W 2 m² 450 W 3 m² 600 W 4 m² 900 W 6 m² 1200 W 8 m² 1500 W 10 m² SafetyIndoor use only. This mat connects to 230–240 V mains and must be installed and wired by a licensed electrician to AS/NZS wiring rules on an RCD-protected circuit. Hotwire systems are independently tested to AS/NZS standards.
$873.06 - $1,723.38
The Hotwire Under Tile Heating Kit is a complete electric floor heating system built for Australian homes. A slim 4 mm heating cable is laid directly over the subfloor before tiling, so the warmth sits just below the floor surface and the room heats up in around 30–60 minutes. Each kit ships with everything needed for a professional result: the heating element, a fully programmable touch screen thermostat with floor temperature probe, installation alarm, fixing tape and manual. Running costs can be as low as a couple of cents per square metre per hour, and a WiFi thermostat upgrade is available.Where to use itIdeal for bathrooms, ensuites, laundries, kitchens and living areas — anywhere tiled floors feel cold underfoot. Because the heating warms and dries wet-area floors, it also helps reduce mould and cleaning. It suits renovations particularly well, since only the floor covering needs to be replaced to install it, and systems scale from a compact 1 m² zone up to large open-plan spaces.How to usePlan the heated area, fix the cable evenly across the subfloor at the spacing shown in the manual, position the floor probe, then tile or screed over the element. All electrical connections and the final wiring of the thermostat must be carried out by a licensed electrician, and continuity/resistance tests should be logged before, during and after installation.Important notesChoose the kit wattage to match the free floor area, excluding fixtures such as vanities, baths and cabinetry. Do not shorten or cut the heating cable. Register the warranty after installation; the heating element carries a lifetime warranty (conditions apply).Specifications Wattage Coverage (approx.) 300 W 1.4–2 m² 600 W 3.4–4 m² 1000 W 6.1–7 m² 1500 W 9–10.7 m² 3000 W 17.9–21.4 m² 6000 W up to approx. 42 m² SafetyIndoor use only. This is a 230–240 V fixed-wiring appliance: installation and connection must be performed by a licensed electrician in accordance with AS/NZS wiring rules, with the circuit protected by an RCD. Independently tested to AS/NZS standards.
$0.00 - $2,756.05
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Premixed Mastic Tile Adhesive is a high performance, ready-to-use wall tile adhesive from Dunlop Trade (ARDEX Australia). Supplied in a convenient 20kg pail, there is no mixing, no mess and no guesswork – just open the lid and start trowelling. Its superior non-slump formulation holds even large format wall tiles and dimensional stone such as marble and granite firmly in place while you work, and its high flexibility and tenacity make it a favourite with tilers who want dependable grab straight off the trowel.Where to use itDesigned for indoor walls only. It is ideal for bathrooms, kitchens, laundries and splashbacks, and its unique formulation allows use in wet areas. Fix ceramic wall tiles, granite and marble (excluding moisture sensitive stone) over cement render, plasterboard, fibre-cement sheet, suitably prepared painted surfaces and Dunlop Waterproofing Membrane (porous tiles only).How to useEnsure surfaces are clean, dry and sound. Spread the adhesive with a suitable notched trowel, working in manageable sections, then press tiles firmly into the ribs with a slight twisting action. Adjust tiles within about 45 minutes of laying (at 23°C and 50% humidity). The adhesive dries in approximately 24 hours depending on temperature, and the porosity of the surface and tiles, after which grouting can proceed.Important notesDo not use over waterproofing membranes with dense or glazed tiles – use porous tiles only, as the adhesive will not dry properly between two non-absorbent layers. Not suitable for floors or exterior applications.Specifications Size 20kg pail Colour White Coverage Approx. 8-10m² per 20kg Tile types Ceramic wall tiles, granite, marble (not moisture sensitive stone) Substrates Render, plasterboard, FC sheet, painted surfaces, Dunlop membrane (porous tiles) Classification D2TE dispersion adhesive SafetyUse in a well-ventilated area and wear protective gloves and eye protection. Avoid skin and eye contact, wash hands after use and keep out of reach of children. Refer to the safety data sheet before use.
$99.60
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that delivers an instant waterproof seal across the joints where leaks start: the junction between floor and wall, and around shower grates and outlets in bathrooms, kitchens and laundries. It is the joint-sealing half of the Dunlop Pro Rapid system; team it with Dunlop Pro Rapid Waterproofing Membrane and tiling can commence just four hours after the membrane is applied, with the finished system meeting Australian Building standards for waterproofing.Where to use itDesigned for internal wet areas such as bathrooms, showers, kitchens and laundries. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheets, wet area grade plasterboard, plywood, internal AAC blocks and panels, concrete cured for a minimum of 28 days, and renders and screeds cured for a minimum of 7 days.How to useEnsure the surface is clean, dry and free of dust. Peel the release liner and press the tape firmly into floor/wall junctions, corners and around grates and outlets, smoothing out air bubbles as you go. Then apply Dunlop Pro Rapid Waterproofing Membrane over the tape and the remainder of the area to complete the system.Important notesSubstrate curing times matter: concrete needs at least 28 days and renders or screeds at least 7 days before taping and waterproofing. This tape is intended for internal applications and is designed to work as a system with the Pro Rapid membrane.Specifications Size 75mm x 15m roll System partner Dunlop Pro Rapid Waterproofing Membrane Tile after 4 hours (as part of Pro Rapid system) SafetyLow-hazard self-adhesive product; take care when cutting lengths and follow the safety directions on the membrane used over it.
$98.41
Dunlop Ardit Feather Finish is a cement-based smoothing compound that skims internal floors to a super-smooth, permanent finish before floor coverings are installed. Powered by ARDEX Ardit technology, it trowels out to a true feather edge and sets so fast that coverings can be applied from just 15 minutes after placement - and it needs no primer on most surfaces, saving a whole step.Where to use itFor indoor use over concrete, existing tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. It is ideal for filling grout joints when covering old tiles with vinyl, smoothing trowel marks in levellers, and taking out minor imperfections before vinyl, carpet or ceramic tiles.How to useEnsure the floor is clean, sound and free of dust, grease and loose material. Mix the powder with clean water to a smooth, creamy paste and apply with a flat steel trowel, working from a feather edge up to 3mm thick. Tight second coats can be applied as the first firms. Any ridges can be shaved or lightly sanded once set for a flawless surface.Important notesIndoor use only and must be covered by a floor covering. Mix small batches to suit the rapid set. No primer is required over common substrates - check the datasheet for unusual surfaces.Specifications Size 3.5kg bag Coverage Approx. 12m² over concrete or 24.5m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyCement powders can irritate eyes, skin and lungs. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated, avoid prolonged contact with the wet compound and wash hands after use. Store out of reach of children.
$82.46
Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications Size 8kg bag Coverage Approx. 27m² over concrete or 55m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.
$125.51
Dunlop Level-Flex Timber Floor Leveller is a high performance, partially self-smoothing latex levelling screed developed specifically for timber floors. Supplied as a complete two-part kit in a handy pail, it combines a cement-based powder with a flexible latex liquid to deliver the adhesion, flexibility and water resistance needed when levelling over floors that move more than concrete does.Where to use itDesigned for indoor use over timber and concrete subfloors, it creates a smooth, flat surface ready for ceramic tiles, carpet or vinyl. It is a popular choice for renovating older homes with uneven timber floorboards or sheet flooring before new coverings are installed.How to useSand and prime timber floors first, and prime porous concrete with a plush broom application. Blend the latex liquid with the powder using a low-speed paddle mixer until smooth, then pour and spread with a trowel, allowing the screed to flow out and self-smooth. The floor is walkable in about 3 hours; lay ceramic tiles after roughly 12 hours (3mm screed), carpet after 24 hours and vinyl after 48 hours.Important notesIndoor use only, and the leveller must be covered by a finished floor covering. Timber must be sound, rigid and well fixed before levelling. Low odour formula makes it comfortable to use in occupied homes.Specifications Size 15.9kg kit (powder plus latex liquid) Coverage Approx. 7m² at 1mm or 2.3m² at 3mm per kit Thickness Feather edge to approx. 12mm (thicker with aggregate) Substrates Timber and concrete Walk-on time 3 hours SafetyWear gloves, safety glasses and a P2 dust mask when handling the cement powder, and keep the room ventilated while mixing. Avoid skin and eye contact with the wet mix, wash after use and store the kit away from children.
$108.45
You have seen 336 out of 763 products
Solutions intended for interior conditions—ideal where low odour, low VOC and clean finishes matter. Great for craft, cabinetry, skirting and general household repairs. Not rated for long-term exterior UV or weather exposure unless explicitly stated. Use filters to refine by chemistry, cure speed and finish (e.g., dries clear, paint-matchable). Always confirm limitations and instructions on the product page and TDS/SDS.
